RAMCRETE FOR RUBBING, SMOOTHING, RESTORATION, RESURFACING, REPAIRING • • • •
Dual Bonding Action Easy to Use Extra rich for smooth, easy troweling Holds moisture while spreading or rubbing
RAM-ROCK ANCHORING CEMENT • NON SHRINK GROUT • Over 5,000 PSI in 1 hour • Over 10,000 PSI in a day • Over 35,000 PSI pullout strength
RAMPATCH / RAMPATCH ACRYLIC
TWO COMPONENT • ACRYLIC POLYMER MODIFIED TOPPING AND UNDERLAYMENT • OVERHEAD AND WALL REPAIRS • Bonds to Virtually Any Concrete Surface • Light Gray to Blend with Existing Concrete • Improved Bond and Compressive Strength
RAMSTRUCTURAL SINGLE COMPONENT • STRUCTURAL REPAIR MATERIAL •Use down to 32°F • Rapid Setting Topping • 8900 PSI Compressive Strength • Ready for Service in 8 Hours
RAM-PRIMER
PRIMER AND SURFACE BONDING • BONDING ADMIXTURE • VOC COMPLIANT • Bond New Concrete to Old • Reemulsifiable, One Time Only • Primer for RAMPATCH and RAM STRUCTURAL
ANCHORING CEMENT • NON SHRINK GROUT
RAM-ROCK Over 5,000 PSI in 1 hour Over 10,000 PSI in a day Over 35,000 PSI pullout strength PRODUCT DESCRIPTION
PRODUCT FEATURES
RAM-ROCK is a scientifically formulated nonmetallic pourable anchoring cement and grout. It is rapid setting and expansive. RAM-ROCK is a non-shrink hydraulic cement with controlled expansion. It will self-level when mixed with water to a pourable consistency. RAM-ROCK is non-rusting and contains no ferrous metals. Its controlled expansion grips the material to be anchored, locking it into place.
$ Fast Setting $ Non-Shrink $ Non-Metallic $ Self-Leveling when Mixing to Pourable Consistency $ Controlled Expansion $ High Compressive Strength $ High Pullout Strength $ Anchors by Expansion $ Meets ASTM 1107 Grade C $ Meets CRD 621
PRODUCT APPLICATION RAM-ROCK may be used to anchor bolts, equipment, machinery, railing, reinforcing rod, signs, posts, etc. It may be used to grout columns, machinery, bearing plates and precast members. RAM-ROCK meets ASTM C-1107 Grade C.
PACKAGING RAM-ROCK is packaged in 50 lb. reusable pails (36 per pallet), 10 lb. reusable pails, and 5 lb. boxes (12 per carton).
PRODUCT SPECIFICATIONS Initial Set: 17 minutes at 75 degrees Final Set: 45 minutes at 75 degrees Expansion: 0.3% Compressive Strength (ASTM C-109, Air Cured): 1 Day 7 Days 10,920 psi 11,060 psi Pullout Strength: (1” diameter bolt anchored in 1-1/2” diameter Hole) 3 days 35,650 psi
RAM-ROCK SURFACE PREPARATION
APPLICATION
All surfaces to be anchored or grouted should be clean and free of any loose particles or debris. The surface to be grouted or anchored should be dampened with clean water, but no standing water should remain.
The hole must be free of loose particles. The hole should be filled with water and scrubbed with a stiff bottle brush. All excess water is to be removed. The hole should be clean and damp. Place anchor bolt with washer in the hole and pour in RAM-ROCK. The washer should be just smaller than the hole. For grouting or anchoring in a vertical wall, force the RAM-ROCK into the hole. Then tamp the bolt or rod into place and finish flush with the wall. Use warm water if a faster set is needed.
MIXING INSTRUCTIONS RAM-ROCK may be mixed to a putty consistency, depending on application. Always mix in a clean container. Excess water will reduce strength and will increase setting time. Pourable Consistency - Step One - Mix 1 pint of water per 5 lb. box, 1 quart of water per 10 lb. pail or 5 quarts of water per 50 lb. pail of RAM-ROCK. Step Two - Mix to a thick paste and allow mixture to stand for about one minute, then stir thoroughly. Putty Consistency - Step One - Mix 7/8 pint of water per 5 lb. box, 1-3/4 pints per 10 lb. pail or 4-1/4 quarts of water per 50 lb. pail of RAM-ROCK. Step Two - Mix for 1 to 2 minutes to a putty consistency.
YIELD 100 lbs. of RAM-ROCK gives 1 cu. ft. of material.
HOLE DIAMETER AND DEPTH Bolt Hole Hole Diameter Diameter Depth 1/4” 3/4” 3” 3/8” 1 4” 1/2” 1-1/2” 4” 5/8” 1-3/4” 6” 3/4” 1-3/4” 6” 1” 2” 8” NOTE: All bolts must have washer just small enough to fit hole.
PRECAUTIONS
RAM-ROCK may erode, if exposed continuously to water. Seal with water base acrylic sealer after curing for 7 days where there is heavy exposure to water. Cup RAM-ROCK over anchor hole to prevent standing water. Contact with RAM-ROCK may cause skin irritation. Use rubber gloves.
LIMITED WARRANTY
Lyons Manufacturing, Inc. warrants the high quality of its products. However, because of many factors beyond our control in its use, such as job conditions, workmanship, etc., the liability of all parties making and selling this product is expressly limited to the refund of the purchase price or replacement of this material used. Lyons Manufacturing, Inc. will replace any product proven to have a manufacturing defect, FOB Factory, provided Lyons Manufacturing, Inc. is notified of such defect within six (6) months from the date of shipment from the factory. This warranty is in lieu of all other warranties, expressed or implied. Lyons Manufacturing, Inc. makes no warranty of suitability of its products for any particular application and sells its proucts upon the condition that customer shall conduct their own test to determine the suitability of the product for their purposes. Under no circumstances will Lyons Manufacturing, Inc. be liable for economic, special, incidental or consequential damages or losses of any kind.
LYONS MANUFACTURING, INC.
8900 Forney Road w Dallas, TX 75227 w 214-381-8100 www.lyonsmanufacturing.com
05 17
TWO COMPONENT • ACRYLIC POLYMER MODIFIED TOPPING AND UNDERLAYMENT • OVERHEAD AND WALL REPAIRS
RAMPATCH *Bonds to Virtually Any Concrete Surface *Light Gray to Blend with Existing Concrete *Improved Bond and Compressive Strength PRODUCT DESCRIPTION
PRODUCT FEATURES
RAMPATCH is a two component polymer modified concrete repair, topping, and underlayment material. The RAMPATCH liquid is a high solids content Acrylic Polymer. The RAMPATCH Powder #RM1005 is a portland cement based mix with graded silica and special chemical additives. Polymer modified concrete gives improved bonding, improved chemical resistance, improved water resistance and improved tensile, compressive and flexural strengths.
This high strength portland cement/acrylic polymer combination provides a smooth durable semi-resilient surface which can be used as a finished floor in most applications. RAMPATCH is easy to mix and apply, requiring no special tools. It is suitable for use as a screedable topping and underlayment, or as a floor, wall or overhead repair material when mixed to a stiffer trowelable consistency. RAMPATCH has been approved by the USDA for use in most processing plants and may be used where there is exposure to potable water. Use of RAMPATCH can help your project earn LEED Credits. Contact factory for details.
PRODUCT APPLICATIONS RAMPATCH is designed to be used both as a topping or underlayment and as a wall, floor, and overhead patching and repair material when mixed to a stiffer consistency. For use as an underlayment, mix to the consistency of a thick pancake batter. Use RAMPATCH to level and smooth rough or rained on concrete. RAMPATCH may be used to level low areas inside or outside. It will bond to and may be used to level virtually any concrete surface. Mixed as a repair material, RAMPATCH may be used to repair walls, floors, tilt panels, driveways, sidewalks, precast members, etc. RAMPATCH may be applied from featheredge to 2-1/2 inches. Suitable for interior or exterior applications. Suitable for application where there is rubber tired forklift and vehicle traffic.
Outstanding Bonding Improved Water Resistance Interior or Exterior Use From Featheredge to 2-1/2 inches May Be Used as Screedable Underlayment May Be Used as a Trowelable Repair Material Improved Compressive Strength No Moist Curing Required High Solids Acrylic Polymer May Be Stained or Used With Integral Color May Be Used for Stenciled and Decorative Concrete LEED Credits Applicable
PRODUCT TEST RESULTS WORKING TIME: Approximately 25 minutes COLOR: Light Gray, also available in White INITIAL SET: 4 Hours SCREEDABLE CONSISTENCY: (1 bag to 1 gallon) Compressive Strength (ASTM C-109, Air Cured) 7 Days - 4120 PSI 28 Days - 5500 PSI
Flexural Strength (ASTM C-348, Air Cured) 7 Days - 1260 PSI 28 Days - 1535 PSI
Slant Shear Bond (ASTM C-1042, Air Cured) 28 Days - 1250 PSI TROWELABLE CONSISTENCY: (1 bag to .8 gallon) Compressive Strength (ASTM C-109, Air Cured) 7 Days - 4550 PSI 28 Days - 6000 PSI
Flexural Strength (ASTM C-348, Air Cured) 7 Days - 1360 PSI 28 Days - 1720 PSI
Slant Shear Bond (ASTM C-1042, Air Cured) 28 Days - 1550 PSI
SURFACE PREPARATION - All surfaces must be clean and structurally sound; free of dust, grease, oil, paint, sealers, etc. Pores of the concrete surface must be open to permit proper bonding, especialy on fresh “green” concrete. Any necessary surface preparation may be done by shotblasting, scarifying, sandblasting or acid etching. If acid etch is used, be sure to neutralize surface, clean and brush thoroughly. For heavy traffic applications, mechanical abrasion of the surface is recommended. Concrete surfaces should be surface saturated but dry to touch (SSD). Do not bridge cracks with RAMPATCH. They will “telegraph” through. Fill cracks prior to placement of RAMPATCH. Expansion joints should be extended through the RAMPATCH. For surfaces with low porosity, an EPOXY PRIMER can be used per installation instructions on the literature. MIXING - RAMPATCH may be mixed in a mortar mixer, with a heavy duty low-to-medium speed drill or by hand. Always use a clean mixing container. Place RAMPATCH Acrylic #RM1003 in container and add RAMPATCH Powder #RM1005, mixing while adding powder. DO NOT ADD WATER. Added water will reduce strength and bonding. Mix for 2 to 3 minutes until a smooth, lumpfree mixture is obtained. Mixing time should not exceed 3 minutes. DO NOT OVERMIX and DO NOT entrap air while mixing. USE OF AGGREGATE - For areas with a thickness over 1/2”, aggregate should be added to RAMPATCH. Add 1 part by volume of 3/8” pea gravel to 2 parts by volume of RAMPATCH. DO NOT ADD WATER. USE AS UNDERLAYMENT OR TOPPING - For use as an underlayment, mix to desired screedable consistency, no more liquid than 1 bag to 1 gallon of polymer. As an underlayment, apply from featheredge to 2-1/2”. Material may be screeded for low places or spread into place with a squeegee. When using as a wearing surface topping, install at least 3/8” thick. DO NOT FEATHEREDGE as a wearing surface topping. For areas over 1/2” in depth aggregate is required. USE AS A TROWELABLE NON-SAG REPAIR MATERIAL- For floor, wall and overhead repairs, mix about 3/4 to 7/8 of liquid polymer to a bag of powder to get a stiffer, trowelable non-sag consistency. Make a trial batch to get desired consistency. Lubricate trowel with polymer to prevent dragging. For wall applications such as coating or filling concrete block, RAMPATCH may be applied with a hopper gun and then floated smooth. INSTALLATION - To insure proper bonding, use RAM-PRIMER or apply a bond slurry coat scrubbed into the surface. The RAMPRIMER will give more reliable and consistent results. Allow the RAM-PRIMER to dry (30-45 minutes) and install RAMPATCH material. Material may be applied up to 24 hours after the RAM-PRIMER. The RAM-PRIMER will re-emulsify one time and may be used for inside and outside applications.
The bond slurry coat is a syrup-like consistency mix of RAMPATCH Powder and RAMPATCH Acrylic. Scrub the slurry coat into the SSD surface. Place RAMPATCH and smooth and spread while slurry coat is still damp. DO NOT LET SLURRY COAT DRY. Screed off to get a smooth flat surface. Use a trowel for touch-up and featheredging. DO NOT OVERTROWEL. Lubricate trowel with polymer to prevent dragging. The #RM1003 RAMPATCH Acrylic makes the materials darker. Less polymer will give a lighter finished surface. For best results, smooth and spread into place and touch-up as needed. A latex film will form when RAMPATCH begins to set. This is normal and will disappear. Normally floor coverings may be applied the next day. With thick applications or cold or damp weather, another day may be required. No heavy traffic should be permitted for 4 to 5 days. When used as an underlayment, always follow the directions of floor covering manufacturers concerning maximum moisture content and perform required tests. Over interior plywood floors, use two coats of RAM-PRIMER applied at right angles. Allow RAM-PRIMER to dry between coats. Floor must be rigid and sound. Anchor metal lathe into wood. This will help hold the RAMPATCH in place. RAMPATCH is more resistant to moisture penetration than regular concrete. Breathable water based sealers may be applied over RAMPATCH as soon as 24 hours. Paints and coatings may be applied over RAMPATCH as you would over concrete. For solvent based sealers and coatings, wait 3-4 days for the RAMPATCH to harden. For non-breathable coatings, ensure moisture has left RAMPATCH. A simple poly test can be performed over the deepest areas. Always follow manufacturer recommendations and testing for applying over fresh concrete. PRECAUTIONS - Do not use below 40oF. The best temperature to use is 60o-90oF. DO NOT LET RAMPATCH ACRYLIC #RM1003 FREEZE. Always make a trial installation first under actual job conditions to be sure you get the desired results before using on larger areas. CONTAINS SILICA SAND AND FREE SILICA. Do not breathe dust. Avoid inhalation by wearing respirator. Continuous exposure and inhalation may cause silicosis and crystalline silica is classified as a known human carcinogen. CURING - In general, RAMPATCH will air cure without any need for curing products. However, care should be taken in areas where RAMPATCH is exposed to wind or direct sunlight, sometimes these can cause cracking as the top dries before the bottom has cured. For these fast drying situations, the RAMPATCH should be covered with damp burlap or plastic for 48 hours. COVERAGE - RAMPATCH Powder #RM1005 is packaged in 45 lb. moisture resistant bags. RAMPATCH Acrylic #RM1003 is packaged in 1 gallon jugs, 4 to a carton. One 45 lb. bag of RAMPATCH Powder #RM1005 and one gallon of RAMPATCH Acrylic #RM1003 will cover 45 sq. ft. at 1/8” thickness.
CONTAINS PORTLAND CEMENT. Avoid eye contact or prolonged contact with skin. Wash thoroughly after handling. In case of eye contact, flush with plenty of water for at least 15 minutes. Consult a physician immediately. Keep out of the reach of children.
LIMITED WARRANTY
Lyons Manufacturing, Inc. warrants the high quality of its products. However, because of many factors beyond our control in their use, such as job conditions, workmanship, etc., the liability of all parties making and selling this product is expressly limited to the refund of the purchase price or replacement of the Lyons material used. Lyons Manufacturing, Inc. will replace any product proven to have a manufacturing defect, FOB Factory, provided Lyons Manufacturing, Inc. is notified of such defect within one (1) year from the date of shipment from the factory. This warranty is in lieu of all other warranties, express or implied. Lyons Manufacturing, Inc. makes no warranty of suitability of its products for any particular application and sells its products upon the condition that customer shall conduct their own test to determine the suitability of the products for their purposes. Under no circumstances will Lyons Manufacturing, Inc. be liable for economic, special, incidental or consequential damages or losses of any kind.
LYONS MANUFACTURING, INC. 8900 Forney Road Dallas, TX 75227-4505 214/381-8100 www.lyonsmanufacturing.com 05 17
SINGLE COMPONENT • STRUCTURAL REPAIR MATERIAL • USE DOWN TO 32OF
RAM STRUCTURAL RAPID SETTING TOPPING • 8900 PSI COMPRESSIVE STRENGTH READY FOR SERVICE IN 8 HOURS PRODUCT DESCRIPTION
PRODUCT FEATURES
RAM STRUCTURAL is one component structural concrete repair material suitable for a wide range of applications. It is portland cement based with select graded silica and proprietary modifiers to enhance strength and durability. This unique combination of materials gives a repair which is dimensionally stable, extremely strong, has an outstanding bond to a concrete surface and provides structural integrity. RAM-PRIMER is used with RAM STRUCTURAL to insure a consistent and reliable bond For surfaces with a low porosity, RAM STRUCTURAL can be installed with an EPOXY PRIMER. RAM STRUCTURAL has an outstanding bond compressive strength, flexural strength, wear resistance and high early strength.
$ $ $ $ $ $ $ $ $
WORKING TIME:
20 Minutes
PRODUCT APPLICATIONS
COLOR:
Light Gray
RAM STRUCTURAL is a fast-setting trowel grade repair material for horizontal application. It may be used to repair parking decks, bridge structures, pier and deck supports, water and sewage treatment plants, factory and warehouse floors, manholes, for concrete topping and other similar applications. Use RAM STRUCTURAL when the repair must be ready for service in 8 hours. Use in cold weather, down to 32OF. It may be used for interior or exterior repairs, above or below grade. RAM STRUCTURAL may be used from 1/2” to 6”. Suitable for applications with vehicle and forklift traffic.
High Early Strength Ready for Service in 8 Hours Apply from 1/2” to 6” Use Down to 32OF High Compressive and Flexural Strength Outstanding Bonding Wearing Surface Interior or Exterior Use, Above or Below Grade Can be Mixed with Integral Color
PRODUCT TEST RESULTS (Typical)
COMPRESSIVE STRENGTH (ASTM C-109, Air Cured) 1 Day 3 Days 7 Days 28 Days 4265 6925 7775 8900 FLEXURAL STRENGTH (ASTM C-348, Air Cured) 3 Days 7 Days 28 Days 879 1227 1790 BOND STRENGTH (ASTM C-1042, Air Cured) 28 Days (P-100 PRIMER) 1490 SHRINKAGE (ASTM C-596) 7 Days 28 Days 0.01% 0.01%
SURFACE PREPARATION - All concrete surfaces must be clean and structurally sound; free of oil, grease, dust, sealers, coatings, release agents, curing compounds, etc. Remove all contaminates mechanically by chipping, shotblasting, grinding or bushhammering. Remove dust by vacuum or blowing with compressed air. All bonding surfaces must be clean and sound, mechanically abraded to 1/8” profile and in a saturated, surface dry condition for application of RAM STRUCTURAL. For surfaces with low porosity, mechanical abrasion can be avoided by utilizing an EPOXY PRIMER per installation instructions on the EPOXY PRIMER literature.
be opened for use in 8 hours; more time is required in cold weather.
MIXING - RAM STRUCTURAL may be mixed with a heavy duty high speed drill and paddle mixer or in a paddle type mortar mixer for higher volume. Place water in mixing container and add power slowly while mixing. Mix thoroughly for 3 minutes. Use 3 quarts of water per 50 lb. bag. DO NOT MIX more material than can be placed in 15 minutes. Use ice water to extend working time, if needed. Integral colors can be added.
CURING - After finishing, follow proper concrete curing procedures. In adverse weather conditions, follow ACI recommended procedures for hot/cold weather. Wet cure after material is hard for 24 hours or apply a high solids water base curing compound. Weathering and surface oxidation may cause a bonding problem with exterior applications.
APPLICATION - Use RAM-PRIMER to insure a good bond. Apply a smooth, even coat of RAM-PRIMER and let it dry before placing RAM STRUCTURAL. RAMPRIMER dries in about a 1/2 hour at 70oF, slower in colder temperatures. See PRECAUTIONS for limits on temperature at installation. For surfaces with low porosity, utilize an EPOXY PRIMER following installation instructions on the EPOXY PRIMER literature. RAM-PRIMER will reemulsify when wet RAM STRUCTURAL comes in contact with it, if applied within 24 hours of RAM-PRIMER drying. Placement should be full depth and continuous to avoid cold joints. RAM STRUCTURAL can be pumped. Do not featheredge RAM STRUCTURAL. Saw cut to obtain straight edge with minimum 1/2” thickness. Finish RAM STRUCTURAL to designed surface finish. Repaired area may
Normally, any required coatings may be applied after 24 hours. Check moisture content before applying nonbreathable coatings, such as epoxy. Paints and coatings may be applied over RAM STRUCTURAL as you would over concrete. Lubricate trowel with water to prevent dragging. RAM STRUCTURAL will not take acid stains, but concrete water based stains and dye and seal products may be used.
USE OF AGGREGATE - Addition of pea gravel is not recommended or required for product performance. PRECAUTIONS - Do not featheredge RAM STRUCTURAL. Do not use below 32oF. Do not install RAM-PRIMER and RAMSTRUCTURAL at surface temperatures below 41oF. Air temperature should not drop below 32oF for the first 2 days of cure. Always make a trial installation under actual job conditions to be sure you get the desired results before using on larger areas. Do not allow material to freeze for 12 hours after application. COVERAGE - One 50 lb. bag of RAM STRUCTURAL yields .41 cu. ft. and will cover 45 sq. ft. at 1/8” thickness. PACKAGING - RAM STRUCTURAL is packaged in 50 lb. bags with moisture resistant lining.
CONTAINS PORTLAND CEMENT. Avoid eye contact or prolonged contact with skin. Wash thoroughly after handling. In case of eye contact, flush with plenty of water for at least 15 minutes. Consult a physician immediately. Keep out of the reach of children. CONTAINS SILICA SAND AND FREE SILICA. Do not breathe dust. Avoid inhalation by wearing respirator. Continuous exposure and inhalation may cause silicosis and crystalline silica is classifed as a known human carcinogen.
LIMITED WARRANTY
Lyons Manufacturing, Inc. warrants the high quality of its products. However, because of many factors beyond our control in their use, such as job conditions, workmanship, etc., the liability of all parties making and selling this product is expressly limited to the refund of the purchase price or replacement of the Lyons material used. Lyons Manufacturing, Inc. will replace any product proven to have a manufacturing defect, FOB Factory, provided Lyons Manufacturing, Inc. is notified of such defect within one (1) year from the date of shipment from the factory. This warranty is in lieu of all other warranties, express or implied. Lyons Manufacturing, Inc. makes no warranty of suitability of its products for any particular application and sells its products upon the condition that customer shall conduct their own test to determine the suitability of the products for their purposes. Under no circumstances will Lyons Manuracturing, Inc. be liable for economic, special, incidental or consequential damages or losses of any kind.
LYONS MANUFACTURING, INC. 8900 Forney Road Dallas, TX 75227 214/381-8100 www.lyonsmanufacturing.com
05 17
RAM-PRIMER
OTHERS
MasterProtect P110 Tammsweld** Level Primer J42 (Thorobond**) MasterTop P200 (MB Primer II**)
ReCrete 20 Fast Patch 928 Perma Patch FP Special Patch Pave Patch
111 Recrete 20 121 Perma Patch VO 122 123
Larsen Weldcrete
Five Star Structural Concrete CTS Cement All Power-Crete
*Also waterproofs
** Moisture Exposure Limited
JRC Rev. May 30, 2017
NOTE: C ross referencing of products above is not intended to suggest same or similar formulations or identical specifications, only that the LYONS MANUFACTURING, INC. products shown will perform satisfactorily on most (probably not all) applications for the referenced products and usually on additional applications. This cross reference also does not imply that another product can be used as an equivalent to a specified Lyons product.
RAM-PRIMER
SikaTop SikaTop SikaTop SikaTop
MasterEmaco T415 Eucocrete Sikarepair 222 (Emaco T415) Eucospeed Sikarepair 223 MasterEmaco T430 Tamms Form and Pour SikaTop 111 RAMSTRUCTURAL (T430) Speedcrete
Concrete Coat Concrete Top Supreme Tamms Thin Patch Tammspatch II Thin-Top Supreme Verticoat Verticoat Supreme
SpecChem Duo Patch Sheppatch Patch Crete
DAYTON SUPERIOR
Emaco 100 MasterEmaco T302 (SD2 Repair Mortar) RAMPATCH
SIKA
Por-Rock Sheprock Flow-rock
ARDEX
MasterFlow 110AN Euco Rock Anchor All (Sonopost) RAM-ROCK
EUCLID/TAMMS
CTS Wunderfixx JetSet Smooth JetSet Wilson Latex Shepcrete Pavecrete
BASF
MasterSeal Tamms Cement Wash Tilt Wall Patch Architectural Finish 581 (Thoroseal*) Tammscrete Verticoat Verticoat Supreme RAMCRETE
PRODUCT
PRODUCT CROSS REFERENCE LIST
From Day One Until Day Done, One Call Gets It All www.ram-tool.com 1-888-RAM-TOOL ALABAMA Birmingham, AL Huntsville, AL Mobile, AL Montgomery, AL FLORIDA Fort Lauderdale, FL Jacksonville, FL Orlando, FL Pensacola, FL Tampa, FL GEORGIA Atlanta, GA Savannah, GA KENTUCKY Louisville, KY LOUISIANA Baton Rouge, LA New Orleans, LA
MISSISSIPPI Gulfport, MS NORTH CAROLINA Charlotte, NC Greensboro, NC Raleigh, NC
TEXAS Austin, TX Corpus Christi, TX Dallas, TX Fort Worth, TX Houston, TX San Antonio, TX
OKLAHOMA Oklahoma City, OK
DISTRICT OF COLUMBIA Washington, DC
SOUTH CAROLINA Charleston, SC Columbia, SC Greenville, SC
VIRGINIA Chesapeake, VA Richmond, VA Roanoke, VA
TENNESSEE Chattanooga, TN Knoxville, TN Memphis, TN Nashville, TN
WEST VIRGINIA Charleston, WV