TYRE SHEILD TYRE SHIELD ® is a puncture preventative that seals holes in both tube type and tubeless tyres caused by puncturing objects up to 6mm in diameter which appear in the tread area of the tyre and 3mm in tube type tyres as the vehicle is being driven. It is an inert substance consisting of an innovative, concentrated liquid polymer compound which is installed by being pumped through the valve stem of tyres (after the valve core has been removed), which are then rotated to evenly distribute and create a thin film on the inside of the treated tyre or tube. The treated tyre is consequently sealed against porous and rim leaks. TYRE SHIELD ® also prevents rust and helps to extend tyre life by the combination of maintaining the correct balance and the prevention of heat build up whilst not effecting the material of the steel or aluminium wheels Pack Size TSP125
TYRE SHIELD 125ml
12
TSP250
TYRE SHIELD 250ml
8
TSP500
TYRE SHIELD 500ml
5
TSP1000
TYRE SHIELD 1 LT
4
TSP20L
TYRE SHIELD 20LT
1
RECOMMENDED MINIMUM AMOUNTS (Per Tyre) Push bike – Road Bike 50ml, MTB 50-75ml Ride-on mower – 60-120ml Motorcycle – 75ml front tyre / 125 ml back tyre Standard car type – 100-150ml (depending on tread width) ATV, UTV and 4WD – 200ml Average Truck tyres – 500ml
Offroad tyres which will be used in High-Risk areas (3-4 punctures a day) can safely install twice the amount - DO NOT exceed on high speed road vehicles.
POINTS TO REMEMBER Sealing will only occur on the tread of the tyre, i.e., from shoulder to shoulder in the tread area. Sealing will not occur on tyre side wall as centrifugal force does not operate on this portion of the tyre, and there is too much flexing in the side wall. PNEUMATIC TYRES TYRE SHIELD ® is only applied into pneumatic tyres, i.e., all tyres which are inflated with air. Caution should be taken that there is no water in tyres before applying the product. Ensure that compressors contain water traps which prevent water from collecting in air lines, as all compressors generate water. UNDER INFLATION PROBLEM: Under inflated tyres can be dangerous. Under inflation is a frequent cause of tyre damage. Excessive flexing, which build up internal heat eventually weakens the side of the tyre. Under inflation will also cause rapid tread wear. SOLUTION: TYRE SHIELD ® seals all porous leaks, thus maintaining correctly inflated tyre pressure in tubeless tyres. PROBLEM: Under inflation leads to poor steering response, reduces cornering ability and can cause loss of control in emergencies.
PROBLEM: Under inflation increases rolling resistance in the tyre. This acts like a dragging brake and can significantly increase fuel consumption. SOLUTION: TYRE SHIELD ® seals all porous leaks in tubeless tyres and rims, thus maintaining correctly inflated tyre pressure. PROBLEM: Under inflation can make the sidewalls of the tyre vulnerable to damage from curbs, potholes and sharp objects on the road. SOLUTION: TYRE SHIELD ® seals all porous leaks in tyre rims and seals punctures in the tread area of tubeless tyres caused by puncturing objects no larger than 6mm as the vehicle is being driven. PROBLEM: Under inflation is dangerous in wet weather, which allows the tread grooves to close up so that water cannot drain away. This causes aquaplaning and can result in total loss of steering control, especially during cornering or braking. SOLUTION: TYRE SHIELD ® seals all porous leaks in tubeless tyre rims, thus maintaining correctly inflated tyres.
SOLUTION: TYRE SHIELD ® seals tyres and rims of porous leaks and will seal most punctures in the tread area of tubeless tyres caused by puncturing objects up to 6mm in diameter as the vehicle is being driven. Ron Angel Wholesale - www.ronangel.com.au - sales@ronangel.com.au - VIC/SA/QLD/NT/WA 03 9464 3366 - NSW 02 9729 7700 - TAS 03 6326 9199