Manual de servicio motos italika dinamo y chinas

Page 1

SERVICE MANUAL 150cc Engine

TABLE OF CONTENTS CHASSIS NUTS AND BOLTS

1

ENGINE

3

LUBRICATION SYSTEM

18

FUEL SUPPLY SYSTEM

22

TRANSMISSION COMPONENTS

27

ELECTRICAL STARTING SYSTEM

30

BELT DRIVE CVT MECHANISM

36

CLUTCH

40

REAR TRANSMISSION SYSTEM

45

ELECTRICAL SYSTEM

50

IGNITION SYSTEM

56

CHASSIS NUTS AND BOLTS Note: ,QVSHFW WKH ¿UVW ZHHN DQG WKHQ HYHU\ PRQWK WKHUHDIWHU. Always pay attention to the unit s nuts and bolts. Some loosening after use is normal. Check to ensure that all nuts and bolts are tight.

Torque Tightening Chart Bolt Diameter 4 5 6 8 10 12 14 16 18

Conventional Marked Bolt N.m Kg.m Ib-ft 1~2 0.1 ~ 0.2 0.7 ~ 1.5 1~4 0.2 ~ 0.4 1.5 ~ 3.0 4~7 0.4 ~ 0.7 3.0 ~ 5.0 10 ~ 16 1.0 ~ 1.6 7.0 ~ 11.5 22 ~ 35 2.2 ~ 3.5 16.0 ~ 25.5 35 ~ 50 3.5 ~ 5.5 25.5 ~ 40 50 ~ 80 5.0 ~ 8.0 36.5 ~ 58 80 ~ 130 8.0 ~ 13.0 58 ~ 94 130 ~ 190 13.0 ~19.0 94 ~ 137.5

N.m 1.5 ~ 3 3~6 8 ~ 12 18 ~ 28 40 ~ 60 70 ~ 100 110 ~ 160 170 ~ 250 200 ~ 280

8.8 Marked Bolt Kg.m Ib-ft 0.15 ~ 0.3 1.0 ~ 2.0 0.3 ~ 0.6 2.0 ~ 4.5 0.8 ~ 1.2 6.0 ~ 8.5 1.8 ~ 2.8 13.0 ~ 20.0 4.0 ~ 6.0 29.0 ~ 43.5 7.0 ~ 10.0 50.5 ~ 72.5 11.0 ~ 16.0 79.5 ~ 115.5 17.0 ~ 25. 123.0 ~ 181.0 20 ~ 28.0 144.5 ~ 202.5

FUEL SWITCH (PETCOCK) • Periodically clean the petcock externally with grease remover and water. • Check for any leaks or seeping fuel. • Replace the petcock if there are any leaks found. This vehicle has a manually operated fuel valve. There are three positions.

“ON” position The normal operating position for the fuel valve lever is the “ON” position. In this position, fuel will ÀRZ WR WKH FDUEXUHWRr.

“RES” position If the fuel level in the fuel tank becomes too low for the engine to operate with the fuel valve lever in the “ON” position, turn the lever to the “RES” position to use the reserve fuel supply, and refuel as soon as possible.

“OFF” position The closing position for the fuel valve is the “OFF” position. When the vehicle is not in use, always make sure the petcock is in the “OFF” position.

),1$/ *($5 2,/ 1RWH ,QVSHFW PRQWKO\ DQG FKDQJH TXDUWHUO\ 1RWH ZHLJKW JHDU RLO LV UHFRPPHQGHG LQ WKH ¿QDO GULYH FDVH +RZHYHU LQ H[WUHPH FROG ZHDWKHU FRQGLWLRQV \RX PD\ QRWLFH WKDW WKH unit LV KDUG WR SXVK ,I WKDW LV WKH FDVH XVH OLJKWHU YLVFRVLW\ RLO VXFK DV ZHLJKW RU HTXLYDOHQW PRWRU F\FOH WUDQVPLVVLRQ ÀXLG ‡ 7R FKHFN OHYHO UHPRYH OHYHO VFUHZ RQ WKH OHIW UHDU HQJLQH FDVH ‡ 7R GUDLQ RLO UHPRYH WKH GUDLQ SOXJ DW WKH UHDU ERWWRP RI WKH HQJLQH FDVH ,W LV UHFRPPHQGHG WR ZDUP WKH HQJLQH IRU PLQXWHV RU PRUH before GUDLQLQJ ¿QDO gear RLO

)LQDO GULYH FDSDFLW\ PO ZHLJKW

(1*,1( 2,/ 1RWH ,QVSHFW EHIRUH HDFK XVH &KDQJH PRQWKO\ ‡ 5HPRYH WKH GUDLQ SOXJ IURP WKH OHIW VLGH ERWWRP RI WKH HQJLQH 'UDLQ LQWR RLO SDQ IRU GLVSRVDO ‡ 5HPRYH WKH ODUJH FDS RQ WKH ULJKW ERWWRP RI WKH HQJLQH DQG UH PRYH WKH VFUHHQ ‡ :DVK WKH VFUHHQ ZLWK FOHDQLQJ VROYHQW DQG UH¿W PDNLQJ VXUH WKH 2 ULQJ LV VWLOO LQ JRRG FRQGLWLRQ ‡ 5H¿OO WKH HQJLQH ZLWK : HQJLQH RLO DQG UXQ IRU PLQXWHV ‡ &KHFN RLO OHYHO RQ WKH ¿OOHU FDS VWLFN WR DVVXUH SURSHU OHYHO ‡ 7KH FDS QHHGV WR EH VFUHZHG LQ IRU D SURSHU UHDGLQJ

&+$66,6 *UHDVH FKDVVLV EXVKLQJV DQG EHDULQJV ZLWK JUHDVH TXDUWHUO\ WR DVVXUH VPRRWK RSHUDWLRQ DQG H[WHQGHG OLIW RI WKH EXVKLQJV DQG WKH FRPSRQHQWV ,I XVHG LQ H[WUHPH ZHW DQG PXGG\ FRQGLWLRQV RU GXVW\ FRQGLWLRQV JUHDVLQJ LV UHFRPPHQGHG PRUH RIWHQ

&$5%85(725 5HIHU WR &DUEXUHWRU VHFWLRQ

9$/9( &/($5$1&( 5HIHU WR (QJLQH VHFWLRQ 2

ENGINE ENGINE COMPONENTS INSPECTION AND SERVICING ENGINE COMPONENTS AND CRANK CONNECTING ROD MECHANISM INSPECTION AND SERVICING

ENGINE COMPONENTS: CYLINDER CYLINDER REMOVAL The removal can be done on the vehicle body. • Remove cylinder head. • Remove cylinder. • Remove cylinder gasket, bolts • Clean cylinder gasket and remove any debris. Caution! Do not damage the cylinder area. Make sure not to drop anything, including cylinder gasket material, into the crankcase.

CYLINDER INNER WALL WEAR INSPECTION Use a bore diameter dial gauge to measure the degree of wear. The measure point is divided into three sectional planes in the axial direction: upper, middle and lower; measure every plane each time on the mutually perpendicular directions (X, Y), the measured least dimension is the cylinder bore; at the most upper position measured is the largest diameter, and the lowest position measured is the smallest diameter, their difference is the cylindricity of the cylinder. At the same cross section, measure the difference of diameter between two points mutually perpendicular; which is the circularity of the cylinder. In order to make the measuring point perpendicular with the bore axis of the cylinder, and to ensure the precision of the measurement, the bar of the gauge can be slightly swung in the direction of the gauge bar, and take the smallest reading number as the result. In the situation without a dial gauge, a feeler gauge can be used to make relativity measurement. put a new piston into the cylinder, and use the feeler gauge to measure the gap between the piston skirt and the cylinder wall. T hen ¿gure out the abrasion loss of the cylinder. If the circularity of the cylinder exceeds the limit, then a cylinder reboring machine should be used to rebore the cylinder, and enlarge its diameter by 0.5mm or 1.00mm, then ¿t the piston and piston ring which size are also enlarged. If the wear is too severe and cannot be reworked, then a new cylinder should be installed. Cylinder bore Cylindricity Circularity

57.4mm 0.05mm 0.05mm

3

&5$1. &211(&7,1* 52' 0(&+$1,60 3,6721 6(7 3,6721 3,1 ,163(&7,21 $1' 6(59,&,1* ‡ ,QVHUW WKH SLVWRQ SLQ KRUL]RQWDOO\ LQWR WKH SLVWRQ SLQ KROH DQG LQVSHFW WKH FOHDUDQFH EHWZHHQ SLV WRQ DQG SLVWRQ SLQ 6HUYLFH /LPLW

PP

,I WKH IUHH SOD\ LV WRR PXFK WKH ZRUQ FRQGLWLRQ RI SLVWRQ SLQ DQG SLVWRQ SLQ KROH PXVW EH LQVSHFWHG UHVSHFWLYHO\

‡ 0HDVXUH WKH H[WHUQDO GLDPHWHU RI SLVWRQ SLQ 6HUYLFH /LPLW

PP

,I WKH UHVXOW LV OHVV WKDQ WKH 6HUYLFH OLPLW LW VKRXOG EH UHSODFHG $IWHU UHSODFHPHQW FKHFN WKH FOHDUDQFH EHWZHHQ SLVWRQ SLQ DQG SLVWRQ SLQ KROH DQG PDNH VXUH LW FRPSOLHV ZLWK WKH UHTXLUHG PHDVXUHPHQW

‡ 0HDVXUH WKH LQQHU GLDPHWHU RI SLVWRQ SLQ 6HUYLFH /LPLW

PP

,I WKH UHVXOW LV PRUH WKDQ WKH VHUYLFH OLPLW LW VKRXOG EH UHSODFHG $IWHU UHSODFHPHQW FKHFN WKH FOHDUDQFH EHWZHHQ WKH KROHV RI WKH SLVWRQ SLQ DQG PDNH VXUH LW FRP SOLHV ZLWK WKH UHTXLUHG PHDVXUHPHQW

3,6721 5,1*6 ,163(&7,21 $1' 6(59,&,1* ‡ ,QVSHFW WKH SLVWRQ ULQJ IRU ÀDZV VHULRXV ZHDU RU VHULRXV FRQJOXWLQDWLRQ HWF ,I WKHUH LV LW VKRXOG EH UHSODFHG ‡ ,I WKH SLVWRQ ULQJ¶V ODWHUDO FOHDUDQFH DQG QRWFK FOHDUDQFH DUH WRR ODUJH RU WRR VPDOO LW ZLOO FDXVH PDOIXQFWLRQV VR LW PXVW EH PHDVXUHG ‡ 0HDVXUH WKH FOHDUDQFH RI WKH SLVWRQ ULQJ LQ WKH SLVWRQ ULQJ JURRYH 7KLV FOHDUDQFH LV WKH SLVWRQ ULQJ¶V ODWHUDO FOHDUDQFH )LUVW 5LQJ 6HFRQG 5LQJ

PP PP

&211(&7,1* 52' (1' ,163(&7,21 ‡ 3XW WKH SLVWRQ SLQ DQG EHDULQJ LQWR WKH FRQQHFWLQJ URG HQG LQVSHFW WKH GHJUHH RI WLJKWQHVV RI WKH SLVWRQ SLQ LQ FRQQHFWLQJ URG HQG ‡ 0HDVXUH WKH LQQHU GLDPHWHU RI WKH FRQQHFWLQJ URG HQG 6HUYLFH /LPLW

PP

:KHQ WKH DEUDVLRQ RI WKH ERUH H[FHHGV WKH OLPLWDWLRQ LW VKRXOG EH UHSODFHG 4

3,6721 5,1*6 6(7 83 %HIRUH VHWWLQJ XS DSSO\ RLO RQ HDFK SLVWRQ ULQJ WKHQ HQODUJH SLVWRQ ULQJV DW WKH VDPH WLPH SXW WKHP RQ WKH SLVWRQ DQG PRYH GRZQZDUGV JUDGXDOO\ XQWLO SLVWRQ ULQJV IDOO LQWR WKH ULQJ JURRYH

3,6721 6(7 ,167$//$7,21 ‡ 5HPRYH WKH JDVNHW DWWDFKHG WR WKH FUDQNFDVH ‡ 0RXQW SLVWRQ RQWR WKH VPDOO HQG RI WKH FRQQHFWLQJ URG 7KH WRS RI WKH SLVWRQ PDUNHG ZLWK ³,1´ VKRXOG EH PRXQWHG WRZDUGV WKH GLUHFWLRQ RI WKH LQOHW SRUW LI WKH PDUN LV ³(;´ WKHQ LW VKRXOG EH PRXQWHG WRZDUGV WKH GLUHFWLRQ RI WKH H[KDXVW SRUW ‡ 0RXQW SLVWRQ SLQ DQG SLVWRQ SLQ FOLS ‡ $SSO\ RLO RQ WKH SLVWRQ SLQ WR OXEULFDWH LW &RYHU WKH FUDQNFDVH SRUW ZLWK D SLHFH RI FORWK WR NHHS WKH SLVWRQ FOLS IURP GURSSLQJ LQWR WKH FUDQNFDVH

&5$1. &211(&7,1* 52' 6(7 7KH FRQQHFWLQJ URG LV WKH FRPSRQHQW WKDW OLQNV WKH SLVWRQ DQG FUDQN 7KH SLFWXUH VKRZV WKH VWUXFWXUH DQG DVVHPEOLQJ UHODWLRQV RI WKH FUDQN FRQQHFWLQJ URG FRPSRQHQW

&5$1.&$6( $1' &5$1.6+$)7 5(029$/ %HIRUH UHPRYLQJ WKH FUDQNFDVH DQG FUDQNVKDIW IROORZ WKHVH SURFHGXUHV ‡ 5HPRYH WKH HQJLQH ‡ 5HPRYH WKH F\OLQGHU FRYHU ‡ 5HPRYH WKH F\OLQGHU ‡ 5HPRYH WKH SLVWRQ

‡ 5HPRYH WKH GULYH SODWH DQG WKH GULYHQ SODWH ‡ 5HPRYH WKH $& JHQHUDWRU ‡ 5HPRYH WKH VWDUWLQJ PRWRU ‡ 5HPRYH WKH RLO SXPS ‡ 7KHQ UHPRYH WKH FDP FKDLQ WHQVLRQHU EROW 5HPRYH WKH FDP FKDLQ WHQVLRQHU ‡ 8VH VSHFLDO WRROV WR UHPRYH WKH VWDUWLQJ GULYHQ JHDU 5

‡ 5HPRYH WKH FUDQNFDVH SRVLWLRQLQJ EROWV ‡ 6HSDUDWH WKH ULJKW FUDQNFDVH DQG WKH OHIW FUDQNFDVH

%H FDUHIXO QRW WR GDPDJH WKH MRLQW IDFH

‡ 5HPRYH WKH JDVNHW DQG WKH GRZHO SLQV

‡ 5HPRYH WKH FUDQNVKDIW IURP WKH FUDQNFDVH ‡ 7DNH RXW WKH FDP FKDLQ

‡ 5HPRYH WKH JDVNHW RQ WKH FUDQNFDVH MRLQW IDFH EH FDUHIXO WR QRW GDPDJH WKH MRLQW IDFH

‡ 5HPRYH WKH RLO VHDO IURP WKH OHIW FUDQNFDVH

‡ 5HPRYH WKH RLO VHDO IURP WKH ULJKW FUDQNFDVH

6

CRANKSHAFT AND CRANKCASE INSPECTION • Replace the whole set of the crankshaft if serious wear is found while inspecting. Measure the axial trend clearance of the big end of the connecting rod. • When measuring, put the large end of the connecting rod close to the crank, and insert the feeler gauge between the other side and the crank, for the correct end play. Service Limit

0.55mm

• Measure the radial trend (X,Y) clearance of the big end of the connecting rod. Service Limit

0.05mm

• Measure the main shaft journal jump of the crankshaft. If this measurement is too great, it will cause the engine to shake abnormally, shortening the life of the engine It must be examined carefully when inspecting. Service Limit

0.10mm(A=90) 0.10mm(B=105)

• Examine if there is any loose, or unusual sound when the crank journal bearing turns. If there is, the whole set should be changed. • After cleaning the crankcase, inspect if there is any damage. • Inspect whether the joint face of the crankcase is smooth and clean. While reassembling, notice if it will affect the sealing performance between the left and right crankcase. ‡ $IWHU WKH DERYH LQVSHFWLRQ LI WKH FUDQNFDVH KDV VRPH VXUIDFH GDPDJH XVH RLOVWRQH WR refinish it. If damage is too severe, replace the cover. Because the right and left crankcase axle hole must be concentric, they should be replaced at the same time.

CRANKSHAFT AND CRANKCASE INSTALLATION • Mount the crankcase oil seal. • Put the cam chain into the left crankcase. • Put the crankshaft into the left crankcase.

Pay attention to avoid damaging the oil seal with the cam chain.

7

‡ 0RXQW WKH QHZ GRZHO SLQV DQG JDVNHW RQ WKH OHIW FUDQNFDVH 7KHQ MRLQ WKH ULJKW FUDQNFDVH DQG OHIW FUDQNFDVH WRJHWKHU ‡ 7LJKWHQ WKH FUDQNFDVH SRVLWLRQLQJ EROWV 7LJKWHQLQJ 7RUTXH

OEV P

‡ 0RXQW WKH VWDUWLQJ GULYHQ JHDU. ‡ 0RXQW WKH FDP FKDLQ WHQVLRQHU. ‡ 0RXQW WKH QHZ 2 ULQJ RQ WKH FDP FKDLQ WHQVLRQHU EROW ‡ $SSO\ VRPH RLO RQ WKH 2 ULQJ ‡ 7LJKWHQ WKH FDP FKDLQ WHQVLRQHU EROW

7KH 2 ULQJ PXVW EH PRXQWHG LQ WKH JURRYH

9$/9( 0(&+$1,60 ,163(&7,21 $1' 6(59,&,1* 7KH SLFWXUH VKRZV WKH FRPPRQ YDOYH WUDLQ RI D IRXU VWURNH HQJLQH 7KLV LV D NLQG RI RYHUKHDG YDOYH WUDLQ LWV LQWDNH SRUW H[KDXVW SRUW FDP VKDIW DUH DOO ORFDWHG LQ WKH F\OLQGHU KHDG WKH YDOYHV ERWWRP XS RYHU WKH FRPEXVWLRQ FKDPEHU

*(1(5$/ ,1752'8&7,21 7KH IRXU VWURNH HQJLQH FRPSOHWHV LWV IRXU VWURNH ZLWK RQH SLVWRQ VWURNH ‡ ,QWDNH VWURNH ‡ &RPSUHVVLRQ VWURNH ‡ ([SDQVLRQ VWURNH ‡ ([KDXVW VWURNH

8

9$/9( &/($5$1&( $'-8670(17 9DOYH FOHDUDQFH LV DQ LPSRUWDQW WHFKQLFDO SDUDPHWHU LQ WKH YDOYH WUDLQ ,Q RUGHU WR enable the engine to run properly, HVSHFLDOO\ ZKHQ WKH HQJLQH LV RYHUKHDWHG RU LQ FROG FRQGLWLRQV D FHUWDLQ FOHDUDQFH PXVW EH NHSW 7KLV FOHDUDQFH LV FDOOHG YDOYH FOHDUDQFH :KHQ WKH HQJLQH LV UXQQLQJ WKH YDOYH FOHDUDQFH PXVW QRW EH WRR ELJ RU WRR VPDOO

• 5HPRYH WKH F\OLQGHU KHDG FRYHU

,QVSHFWLRQ DQG DGMXVWPHQW VKRXOG EH GRQH LQ FRRO FRQGLWLRQV EHORZ R&

• 7XUQ WKH FRROLQJ IDQ FORFNZLVH XQWLO WKH PDUN RI WKH WLPLQJ GULYH VSURFNHW RQ WKH FDPVKDIW LV DW WKH WRS GHDG FHQWHU DQG WKH ³7´ V\PERO RU RWKHU PDUN RI WKH PDJQHWR À\ZKHHO DOLJQV WR WKH FUDQN FDVH PDUN 7KH FUDQNVKDIW VKRXOG URWDWH RU WKH H[KDXVW SRUW PD\ QRW EH DGMXVWHG • :KHQ DGMXVWLQJ ORRVHQ WKH ORFN QXWV DGMXVW WKH EROWV ZLWK D YDOYH DGMXVWLQJ ZUHQFK. WKHQ WXUQHG FORFNZLVH WKH YDOYH FOHDUDQFH GHFUHDVHV WKHQ WXUQHG FRXQWHUFORFNZLVH WKH YDOYH FOHDUDQFH LQFUHDVHV 3XW D IHHOHU JDXJH ZLWK VSH FL¿F VL]HV EHWZHHQ WKH YDOYH DQG URFNHW WR FKHFN IRU FRUUHFW FOHDUDQFH • 7DNH RXW WKH IHHOHU JDXJH WLJKWHQ WKH ORFN QXWV DQG WKHQ LQVSHFW WKH YDOYH FOHDUDQFH DJDLQ 6RPHWLPHV ZKHQ WLJKWHQLQJ WKH ORFN QXWV WKH FOHDUDQFH ZLOO FKDQJH VR LW PXVW EH UHFKHFNHG IRU WKH SURSHU FOHDUDQFH

9DOYH &OHDUDQFH

a PP

9

&$06+$)7 7KH FDPVKDIW LV the PDLQ GULYLQJ XQLW RI WKH YDOYH WUDLQ 7KH DLU LQOHW FDP WKH H[KDXVW FDP DQG WKH FDP MRXUQDO DUH RQ WKH VKDIW ,W causes WKH LQWDNH DQG H[KDXVW YDOYH WR RSHQ DQG FORVH DW WKH FRUUHFW WLPH :HDU WR WKH FDPVKDIW ZLOO DIIHFW HQJLQH SHUIRUPDQFH DQG FDXVH H[FHVVLYH QRLVH

&$06+$)7 5(029$/ ‡ /RRVHQ YDOYH FRYHU EROWV DQG UHPRYH FRYHU ‡ 5HPRYH WKH FDP FKDLQ WHQVLRQDO EROW FDS DQG UHPRYH WKH 2 ULQJ ‡ 7LJKWHQ WKH FDP FKDLQ WHQVLRQHU E\ DGMXVWLQJ EROW FORFNZLVH

‡ 7XUQ WKH À\ZKHHO FRXQWHUFORFNZLVH WR PDNH WKH ³ 7´ PDUN RQ WKH À\ZKHHO DOLJQ ZLWK WKH PDUN RQ WKH FUDQNFDVH :KHQ WKH KROH RQ WKH FDP FKDLQ WLPLQJ GULYH FKDLQ ZKHHO LV XS LW VKRXOG EH DW WKH WRS GHDG FHQWHU

‡ 5HPRYH WKH F\OLQGHU KHDG SRVLWLRQLQJ EROW ‡ 5HPRYH WKH FDPVKDIW KROGHU EROW FDS DQG ZDVKHU ‡ 5HPRYH WKH FDPVKDIW KROGHU DQG GRZHO SLQ

‡ 5HPRYH WKH FDP FKDLQ ZKHHO IURP WKH FDP FKDLQ DQG UHPRYH WKH FDPVKDIW

&$06+$)7 ,163(&7,21 ‡ ,QVSHFW WKH FDPVKDIW EHDULQJV IRU SOD\. II WKHUH LV too much play, UHSODFH WKH ZKROH VHW ‡ ,QVSHFW FDP VXUIDFH IRU GDPDJH ‡ 0HDVXUH WKH KHLJKW RI WKH FDP ,QOHW &DP ([KDXVW &DP

PP PP

0

CAMSHAFT INSTALLATION ‡ 5RWDWH WKH À\ZKHHO WR DOLJQ WKH ³7´ PDUN RQ WKH À\ZKHHO ZLWK WKH FDPVKDIW PDUN 7KH URXQG KROH RQ WKH FDP FKDLQ ZKHHO VKRXOG EH XS DQG WKH OHIW DQG ULJKW VLW SDUDOOHO ZLWK WKH F\OLQGHU KHDG WKH OREHV RI WKH FDPVKDIW DUH GRZQ 7KHQ LQVWDOO WKH FDPVKDIW RQ WKH F\OLQGHU KHDG ‡ 0RXQW WKH FDP FKDLQ RQ WKH FKDLQ ZKHHO ‡ ,QVWDOO WKH GRZHO SLQV ‡ 0RXQW WKH FDPVKDIW KROGHU ZDVKHU DQG EROW FDS RQ WKH F\OLQGHU KHDG • 7LJKWHQ WKH F\OLQGHU KHDG EROW DQG QXW :KLOH LQVWDOOLQJ DSSO\ VRPH RLO RQ WKH WKUHDG RI WKH FDPVKDIW KROGHU EROW 7KH FDPVKDIW QXWV VKRXOG EH WLJKWHQHG GLDJRQDOO\ LQ D VWHS SURFHVV $IWHU LQVWDOOLQJ DGMXVW WKH YDOYH FOHDUDQFH • 7XUQ WKH FDP FKDLQ WHQVLRQHU DGMXVWLQJ EROW FRXQWHU FORFNZLVH DQG UHOHDVH WKH ORFN • $SSO\ RLO RQ WKH QHZ 2 ULQJ ‡ 0RXQW DQG WLJKWHQ WKH FDP FKDLQ WHQVLRQHU FRYHU EROW 7KH 2 ULQJ PXVW EH PRXQWHG SURSHUO\ LQ WKH JURRYH ‡ 5HSODFH WKH YDOYH FRYHU JDVNHW DQG PRXQW WKH FRYHU 7KH YDOYH FRYHU JDVNHW PXVW EH SURSHUO\ PRXQWHG LQ WKH JURRYH • 7LJKWHQ WKH YDOYH FRYHU SRVLWLRQLQJ EROW

ROCKER ARM AND ROCKSHAFT ROCKER ARM AND ROCKSHAFT REMOVAL ‡ 5HPRYH WKH FDPVKDIW KROGHU • 7DNH RXW WKH URFNVKDIW E\ UHPRYLQJ WKH EROW ‡ 5HPRYH WKH URFNHU DUP

ROCKER ARM AND ROCKSHAFT INSPECTION ,QVSHFW LI WKHUH LV DQ\ DEUDVLRQ RU GDPDJH RQ WKH URFNHU DUP DQG URFNVKDIW RU LI WKH RLO KROH LV FORJJHG ,I WKHUH LV DEUDVLRQ RQ WKH VXUIDFH RI WKH URFNHU DUP WKH FDPVKDIW VKRXOG DOVR EH LQVSHFWHG

11

• Measure the inner diameter of the rocker arm. Service Limit

10.04mm

• Measure the outer diameter of the rockshaft. Service Limit

9.96mm

ROCKER ARM AND ROCKSHAFT INSTALLATION 噝 R ead the “ EX” mark on the camshaft holder, then mount the exhaust port rocker arm to the rockshaft. • M ount the inlet port rocker arm to the rockshaft. Apply some oil to the rockshaft before mounting.

CAM CHAIN TENSIONER The chain tensioner must be in good working condition for proper chain tension. 1. Cam chain 2. Cam chain tensioner 3. Cam chain tensioner lifter. 4. Gasket 5. Cam chain tensioner pivot 6. Cam chain guide 7. Bolt 8. Nut 9. O-ring 10. O-ring

The operational principle of the tensioner is as shown in the picture.

As for the adjustment of the cam chain tensioner, clockwise tightens, and counterclockwise loosens.

12

VALVE AND VALVE SPRING VALVE AND VALVE SPRING REMOVAL • Remove cylinder head. • Remove valve cotter pin and compressor. • Remove upper spring race. • Remove valve spring. • Remove lower spring race. • Remove valve stem oil seal. • Remove valve. The removed parts should be placed in order to avoid confusion. It’s better to place the intake valve parts and exhaust valve parts separately.

VALVE AND VALVE SPRING INSPECTION • Inspect the valve for bending or burning. • Inspect for smooth action between the valve and the valve guide. • Measure the outer diameter of the valve stem. Service Limit

4.94mm

• Measure the free length of the inner and outer valve spring. Valve Inner spring Outer spring

Inlet valve 31.2mm 34.1mm

Exhaust valve 31.2mm 34.1mm

VALVE AND VALVE SPRING INSTALLATION • Mount the spring retainer, valve guide oil seal. It is recommended to replace the valve guide oil seal with a new one. • After applying oil on the valve stem, mount it into the valve guide. • Mount the inner and outer valve springs. • Mount the valve locker with a spring compressor. When mounting, the twisting direction of the inner and outer springs must be opposite. • Tap on the valve gently two or three times with a rubber hammer to make the valve and the valve lock connect well. Do not damage the valve.

13

VALVE GUIDE Carbon accumulation on the valve guide will make the valve move roughly, causing the valve to not open or close properly. Valve guide abrasion is one of the causes of white smoke from the exhaust pipe.

TO CLEAN CARBON ACCUMULATION OFF THE VALVE GUIDE • Remove the valve and springs etc. • Clean the carbon accumulation with a valve guide reamer. Generally, only turn right when using the reamer, and do not push in or out directly with the reamer.

VALVE GUIDE INNER DIAMETER MEASUREMENT Service Limit

5.03mm

Calculate the clearance between the valve stem and the valve guide (the inner diameter of the guide subtracted by the outer diameter of the valve stem).

Valve Service Limit

Inlet valve 0.08mm

Exhaust valve 0.10mm

When the abrasion of the valve guide exceeds the service limit, it should be replaced; after replacing a new valve guide, the valve retainer must be adjusted.

VALVE GUIDE REPLACEMENT • Heat the cylinder head to 212 ~ 302°F (100 ~ 150°C) The cylinder head must be wholly and quickly heated WR WKH VSHFLÂżF GHJUHH DQG FDQQRW EH KHDWHG SDUWOy, or it will cause the cylinder head to distort. The temperature is very high, two technicians are recommended. • Tap the valve guide out with a valve guide remover or similar tool. Do not damage the cylinder joint face

14

• After tapping the valve guide, you need to trim it with a reamer. When using the reamer, cutting oil must be used. The reamer can only be turned right; do not push in or out directly. • Clean the cylinder head, and remove the scraps generated while ramming.

VALVE SEAT The relative position between the valve seat and the working surface of the valve is very important for the valve to seal properly.

VALVE SEAT WIDTH MEASUREMENT • Clean the carbon accumulation in the combustion chamber. • Measure the width of the valve seat with a vernier caliper. Standard Service Limit

0.6-1.2mm 1.8mm

When abrasion causes the valve seat width to be uneven, too wide or too narrow, it will result in poor contact between the valve and the valve seat, and not seal tight. At this time it must be reamed with a customized valve seat milling cutter. The valve seat milling cutter is the customized trimming tool for the valve seat, and it has three cutting angles: 32, 45, and 60. While trimming, press the valve seat milling cutter to make rotary motion with 40 ~ 50 N force. Some oil must be applied on the valve seat milling cutter, to eliminate scraping when trimming.

VALVE SEAT FINISHING • Ream out the defects on the working surface with a 45° coarse tooth milling cutter. Do not ream too much.

15

‡ 5HDP WKH XSSHU DQJOHV RI WKH YDOYH VHDW ZRUNLQJ VXUIDFH ZLWK D ƒ PLOOLQJ FXWWHU

‡ 5HDP WKH ORZHU DQJOHV RI WKH YDOYH VHDW ZRUNLQJ VXUIDFH ZLWK D ƒ PLOOLQJ FXWWHU

‡ )LQDOO\ UHDP WKH YDOYH VHDW WR WKH VSHFL¿F VHDW ZLGWK ZLWK D ƒ PLOOLQJ FXWWHU

9$/9( 6($7 728&+,1* 326,7,21 ,163(&7,21 $SSO\ D WKLQ OD\HU RI ÀXLG RQ WKH YDOYH VHDW. Place WKH YDOYH RQ WKH VHDW DQG URWDWH MRLQWO\; WKHQ WDNH RXW WKH YDOYH DQG REVHUYH WKH FRQWDFW VXUIDFH RQ WKH YDOYH IDFH ,I WKH FRQWDFW SRVLWLRQ LV WRR KLJK FXW RXW VRPH RI WKH XSSHU SDUW RI WKH YDOYH VHDW ZLWK D ƒ PLOOLQJ FXWWHU WR UHGXFH WKH ZRUNLQJ IDFH RI WKH YDOYH VHDW ‡ ,I WKH FRQWDFW SRVLWLRQ LV WRR ORZ WKHQ FXW RXW VRPH RI WKH ORZHU SDUW RI WKH YDOYH VHDW ZLWK D ƒ PLOOLQJ FXWWHU WR UDLVH WKH ZRUNLQJ IDFH RI WKH YDOYH VHDW ‡ )LQDOO\ PLOO WKH ZRUNLQJ IDFH RI WKH YDOYH VHDW WR WKH VSHFL¿F ZLGWK ZLWK D ƒ PLOOLQJ FXWWHU ‡ ,I WKH YDOYH VHDW VWLOO FDQQRW FRQWDFW HYHQO\ ZLWK WKH YDOYH DIWHU WULPPLQJ WKH YDOYH VKRXOG EH UHYLVHG RU UHSODFHG

16

9$/9( $1' 9$/9( 6($7 /$33,1* $IWHU ¿QLVKLQJ WKH YDOYH DQG VHDW VKRXOG EH ODSSHG LQ RUGHU WR PDNH WKHP VHDO SURSHUO\ 6SUHDG D WKLQ OD\HU RI VLOLFRQ FDUELGH RQ WKH ZRUNLQJ EHYHO RI WKH YDOve. UVing D YDOYH VXFWLRQ FXS WRRO, UHSHDWHGO\ URWDWH WKH YDOYH VXFWLRQ FXS WR ODS WKH YDOYH DQG YDOYH VHDW HYHQO\ XQWLO WKH\ PDWFK WLJKWO\

‡ %HIRUH ODSSLQJ FOHDQ WKH YDOYH YDOYH VHDW DQG YDOYH JXLGH ‡ :KHQ ODSSLQJ GR QRW XVH WRR PXFK IRUFH ‡ 'XULQJ ODSSLQJ GR QRW GURS DQ\ VLOLFRQ FDUELGH LQWR WKH area EHWZHHQ WKH YDOYH OHYHU DQG WKH YDOYH JXLGH

9$/9( $1' 9$/9( 6($7 $,5 ,03(50($%,/,7< ,163(&7,21 $IWHU ODSSLQJ WKH YDOYH DQG YDOYH VHDW WKH DLU LPSHUPHDELOLW\ RI WKH MRLQW VXUIDFH VKRXOG EH LQ VSHFWHG 0HWKRG 2QH Follow the same method as for ³YDOYH VHDW FRQWDFW SRVLWLRQ LQVSHFWLRQ´ 0HWKRG 7ZR HYHQO\ GUDZ VHYHUDO OLQHV RQ WKH ZRUNLQJ VXUIDFH RI WKH YDOYH ZLWK D SHQFLO 3lace WKH YDOYH LQWR WKH YDOYH VHDW. Turn a ULQJ. If the lines are all broken, the level of air LPSHUPHDELOLW\ LV satisfactory 0HWKRG 7KUHH MRXQW WKH YDOYH RQ WKH F\OLQGHU KHDG DQG ¿OO WKH LQOHW DQG H[KDXVW YHQW ZLWK QRQ ÀDPPDEOH VROYHQW DQG SUHVHUYH IRU PLQXWHV LI WKHUH LV QR OHDNDJH WKH YDOYH LV VHDWHG FRUUHFWO\

17

LUBRICATION SYSTEM INSPECTION AND SERVICING GENERAL INTRODUCTION The picture shows the functional diagram of the lubrication system. After the lubrication oil crosses WKH ¿OWHU VFUHHQ, it is pumped by the rotator oil pump. Some of the oil goes into the big end of the connecting rod and splashes on the cylinder wall and the small end of the connecting rod; the rest goes through some oil passages, such as the shaft neck of the camshaft, and splashes on the cam rockshaft and cam chain. The lubrication oil that falls back into the oil groove can be recirculated.

18

2,/ 6<67(0 ,163(&7,21 $1' 5(3/$&(0(17 2,/ 5(3/$&(0(17 7LJKWHQ WKH GLSVWLFN. 5HPRYH WKH RLO ¿OWHU VFUHHQ FDS DQG WKH VFUHHQ WR allow WKH RLO ÀRZ RXW

,QVSHFW WKH VFUHHQ DQG 2 ULQJ. Replace if damaged. 0RXQW and tighten WKH RLO ¿OWHU VFUHHQ DQG WKH VFUHHQ FRYHUV. 6XSSO\ WKH DSSOLFDWLRQ VSHFL¿F RLO WR WKH appropriate OHYHO

2LO /HYHO

'LVDVVHPEOLQJ O

5HSODFLQJ O

6WDUW WKH HQJLQH DQG UXQ IRU VHYHUDO PLQXWHV LQ WKH LGOH SRVLWLRQ WR PDNH VXUH WKHUH LV QR RLO OHDkage. Stop the engine and inspect for proper oil level.

527$5< 2,/ 3803

7KH RLO SXPS LV WKH FULWLFDO FRPSRQHQW RI WKH OXEULFDWLRQ V\VWHP. Inspect and maintain it SHULRGLFDOO\. If GDPDJHG VHULRXVO\, replace it as a unit.

2,/ 3803 5(029$/ 5HPRYH WKH À\ZKHHO RI WKH PDJQHWR 5HPRYH WKH VWDWRU FRLO DQG WULJJHU ZLQGLQJ

5HPRYH WKH ULJKW FUDQNFDVH FRYHU EROWV, followed by removing WKH ULJKW FUDQNFDVH FRYHU 5HPRYH WKH JDVNHW DQG GRZHO SLQV

19

‡ 5HPRYH WKH VWDUWLQJ UHGXFWLRQ JHDU DQG VWDUWLQJ FOXWFK ‡ 5HPRYH WKH RLO SXPS SDUWLWLRQ SODWH SRVLWLRQLQJ EROWV followed by removing WKH RLO SXPS SDUWLWLRQ SODWH ‡ 5HPRYH WKH RLO SXPS GULYLQJ JHDU QXWV followed by UHPRYing WKe GULYLQJ JHDU DQG FKDLQ ‡ After removing WKH RLO SXPS SRVLWLRQLQJ EROWV UHPRYH WKH RLO SXPS DVVHPEO\

‡ 5HPRYH WKH VFUHZV DQG GLVDVVHPEOH WKH RLO SXPS

2,/ 3803 ,163(&7,21 ‡ ,QVSHFW WKH FOHDUDQFH EHWZHHQ WKH RLO SXPS ERG\ DQG WKH RXWHU URWDWRU 6HUYLFH /LPLW

PP

‡ ,QVSHFW WKH FOHDUDQFH EHWZHHQ WKH LQQHU URWDWRU DQG WKH RXWHU URWDWRU 6HUYLFH /LPLW

PP

‡ ,QVSHFW WKH FOHDUDQFH EHWZHHQ WKH URWDWRU SODQH DQG WKH RLO SXPS 6HUYLFH /LPLW

PP

,I WKH LQVSHFWLRQ UHVXOW H[FHHGV WKH DERYH VWDWHG VHU YLFH OLPLW WKH ZKROH VHW VKRXOG EH UHSODFHG

0

2,/ 3803 $66(0%/,1* ‡ $VVHPEOH WKH LQQHU DQG RXWHU URWDWRUV RI WKH SXPS DQG PRXQW WKH RLO SXPS VKDIW :KHQ DVVHPEOLQJ DOLJQ WKH XQ¿OOHG FRUQHU RI WKH RLO SXPS VKDIW ZLWK WKH FRUQHU RI WKH LQQHU URWDWRU DQG WKHQ PRXQW

‡ 0RXQW WKH GRZHO SLQ \RX FDQ LQVWDOO LW DIWHU DOLJQLQJ WKH RLO SXPS SODWH ZLWK WKH GRZHO SLQ ‡ 7LJKWHQ WKH RLO SXPS SODWH EROWV ‡ $IWHU DVVHPEOLQJ JHQWO\ WXUQ WKH RLO SXPS VKDIW DQG PDNH VXUH WKH RLO SXPS FDQ WXUQ VPRRWKO\

2,/ 3803 ,167$//$7,21 ‡ ,QVWDOO WKH RLO SXPS RQ WKH FUDQNFDVH %HIRUH LQVWDOOLQJ ¿OO WKH RLO SXPS ZLWK RLO :KHQ LQVWDOOLQJ WKH DUURZ RI WKH RLO SXPS ERG\ PXVW EH SRLQWLQJ XSZDUGV

‡ 7LJKWHQ WKH RLO SXPS SRVLWLRQLQJ EROWV ‡ $OLJQ WKH RLO SXPS GULYLQJ JHDU ZLWK WKH RLO SXPS VKDIWV XQ¿OOHG FRUQHU WKHQ PRXQW WKH GULYLQJ JHDU DQG FKDLQ ‡ 0RXQW WKH GULYLQJ JHDU SRVLWLRQLQJ QXW DQG WLJKWHQ LW

‡ ,QVWDOO WKH SDUWLWLRQ ERDUG DQG WLJKWHQ EROWV

‡ ,QVWDOO WKH VWDUWLQJ UHGXFWLRQ JHDU DQG VWDUWLQJ FOXWFK ‡ 0RXQW WKH JDVNHW DQG GRZHO SLQV

1

• Mount the right crankcase cover positioning bolt. • Mount the trigger winding and the stator coil. • Tighten the right crankcase cover positioning bolt. The bolt should be gradually diagonally tightened in two to three steps. $IWHU ¿QLVKLQJ WKH LQVWDOODWLRQ LQspect for any oil leaks.

FUEL SUPPLY SYSTEM INSPECTION AND SERVICING CV CARBURETOR The CV carburetor is a constant vacuum carburetor. The picture shows the structure of the CV carburetor. 1. Gasket set 2. Float valve set 3. Needle jet set 4. Float set 5. Float chamber set 6. Screw set A 7. Screw set B 8. Valve plate set 9. Starter valve set 10. Air cut valve set 11. Compression coil spring 12. Screw 13. Carburetor assy. 14. Top comp. 15. Vacuum piston comp.

16. Needle jet holder 17. Plate clip 18. Holder cap 19. Tube A 20. Tube B 21. Screw 22. Screw 23. Washer screw 24. Washer screw 25. Washer screw 26. Clip 27. Clip 28. Tube 29. Main jet 30. Slow jet

4

1 6

22

CARBURETOR IDLING ADJUSTMENT AIR ADJUSTING SCREW ADJUSTMENT Step one: T urn on the air adjusting screw in the turn out by the prescribed number of turns. Turn out number of turns

2 3/4 – 2 1/4

Step two: Adjust the throttle by adjusting the screw to the prescribed idle rpm. Step three: Left and right, adjust the air adjusting screw slightly to ¿nd the highest position of the rpm. Increase throttle quickly and gently (the rpm is from low to high), and return throttle immediately, then observe 10 to 15 minutes, to observe if the idle remains the same.

VACUUM CHAMBER The picture shows the structure of the vacuum chamber of the CV carburetor.

VACUUM CHAMBER REMOVAL • Remove the body cover. Remove the automatic choke lead wire. • Loosen the fuel drain bolt, and drain the fuel in the Àoat chamber. Remove the fuel line and the vacuum pipe. • Loosen the throttle cable adjusting nut and positioning nut; remove the throttle cable. • Loosen the carburetor air inlet vent clip and the inlet manifold clip; remove the carburetor.

• Remove the vacuum cover bolt, and remove the vacuum cover. Notice: move slowly to prevent the spring from ejecting.

• Take out the spring, the vacuum membrane and the plunger.

• Press down the holding clamp of the needle valve top, and turn left to take out the clamp. • Take out the spring and needle valve. Do not damage the vacuum membrane. • Inspect the needle valve for wear. • Inspect the vacuum membrane for damage. • Inspect the plunger for damage. 23

9$&880 &+$0%(5 ,167$//$7,21 ‡ 0RXQW WKH SOXQJHU DQG WKH YDFXXP PHPEUDQH LQWR WKH FDUEXUHWRU ERG\ ‡ 3XVK WKH SOXQJHU XSZDUGV LQ WKH GLUHFWLRQ RI WKH YDFXXP FKDPEHU FRYHU WR RSHQ WKH FDUEXUHWRU MHW WXEH Insert the spring ‡ $OLJQ WKH EXOJH SDUW RI WKH YDFXXP PHPEUDQH ZLWK WKH ¿OOLVWHU RI WKH FDUEXUHWRU ERG\; PRXQW WKH vacuum FKDPEHU FRYHU ‡ 7LJKWHQ WKH EROW

$8720$7,& 6,'( 67$57(5 &+2.(

$8720$7,& 6,'( 67$57(5 ,163(&7,21 ‡ 5HPRYH WKH IXHO KRVH IURP WKH FDUEXUHWRU ‡ 7XUQ RXW WKH FDUEXUHWRU ÀRDW FKDPEHU GUDLQ VFUHZ DQG GUDLQ WKH IXHO LQ WKH FDUEXUHWRU ‡ 5HPRYH WKH DXWRPDWLF VLGH VWDUWHU OHDG ZLUH DQG UHPRYH WKH FOLS ‡ 5HPRYH WKH FDUEXUHWRU FODPS DQG UHPRYH WKH FDUEXUHWRU ‡ &KHFN WKH FRQGLWLRQ RI WKH FRQQHFWLRQ EHWZHHQ WKH WZR OHDG ZLUHV 7KH FKRNH YDOXH VKRXOG EH EHORZ 9 ,I LW H[FHHGV WKH VSHFL¿F YDOuH LW VKRXOG EH UHSODFHG :KHQ WKH HQJLQH LV FROG OLQN D KRVH RQ WKH UHVHUYH VXSSO\ IXHO OLQH DQG EORZ YHU\ JHQWO\ ,I LW LV RE VWUXFWHG RU WKH DXWR VLGH VWDUWHU LV QRW JRRG LW VKRXOG EH UHSODFHG ‡ 5HPRYH WKH DXWR VLGH VWDUWHU FRYHU ‡ 5HPRYH LWV SRVLWLRQLQJ EROWV DQG SLHFHV ‡ 5HPRYH WKH DXWR VLGH VWDUWHU ‡ ,QVSHFW WKH DXWR VLGH VWDUWLQJ YDOYH DQG IXHO LQMHFWLRQ QHHGOH IRU ZHDU ‡ ,QVSHFW WKH 2 ULQJ for ZHDU

)/2$7 &+$0%(5 )/2$7 &+$0%(5 5(029$/ ‡ 5HPRYH WKH FDUEXUHWRU ‡ 5HPRYH WKH FODPS DQG UHPRYH WKH ÀRDW FKDPEHU ‡ 5HPRYH WKH 2 ULQJ; WXUQ RXW WKH ÀRDW FKDPEHU VFUHZ; UHPRYH WKH ÀRDW SLQ; DQG UHPRYH WKH ÀRDW DQG ÀRDW YDOYH ‡ 5HPRYH WKH FKRNH DGMXVWLQJ VFUHZ DQG DLU DGMXVWLQJ VFUHZ 24

Before removing ¿rst tighten the two screws gently, counting the number of turns Remove screws. Do not use excessive force to avoid damaging the air adjusting screw head surface. • Remove the main fuel injection nozzle and fuel injection needle seat.

FLOAT CHAMBER INSTALLATION ,QVSHFW WKH ÀRDW IRU DQ\ GDPDJH DQG IRU IXHO LQ WKH ÀRDW ,QVSHFW WKH ÀRDW YDOYH DQG Àoat valve seat for wear. If there is wear, it should be replaced. Clear every fuel line and air line on the carburetor body with compressed air.

FLOAT CHAMBER INSTALLATION • Install the main fuel injection nozzle and fuel injection needle seat. • Install the air adjusting screw and choke adjusting screw, and turn them to the proper position according to the noted number of turns while removing. ‡ 0RXQW WKH ÀRDW YDOYH WKH ÀRDW DQG WKH ÀRDW SLQ • TLJKWHQ WKH ÀRDW SLQ SRVLWLRQLQJ VFUHw.

FUEL LEVEL INSPECTION • Measure the fuel level height. Fuel level height

18.5mm

‡ ,QVSHFW WKH ÀRDW IRU DQ\ GDPDJH DQG LQVSHFW WKH Àoat valve for excess wear. ‡ &RQ¿UP WKDW WKH XS DQG GRZQ PRYHPHQW RI WKH Àoat is normal.

CARBURETOR INSTALLATION ‡ ,QVSHFW WKH ÀRDW IRU DQ\ GDPDJH DQG LQVSHFW WKH Àoat valve for excess wear. ‡ &RQ¿UP WKDW WKH XS DQG GRZQ PRYHPHQW RI WKH Àoat is normal.

CARBURETOR INSTALLATION • Reverse the removal procedure for installation. • After installing, confirm that all carburetor linkage and cables are in correct position. Verify that carburetor is in idle position.

25

AIR CUT VALVE (ACV) The air cut valve can avoid some abnormalities when the throttle closes too quickly. The structure of the air cut valve is shown in the picture.

AIR CUT VALVE REMOVAL • Remove the air inlet manifold of the cut valve. • Remove the bolt. R emove the vacuum membrane cover, the spring, and the vacuum membrane.

AIR CUT VALVE INSTALLATION • Mount the vacuum membrane on the carburetor. • Mount the spring, the vacuum membrane cover, and the lock bolt.

The bottom side of the vacuum membrane should be aligned with the carburetor. The top side should be aligned with the vacuum membrane.

AIR CHECK VALVE The air check valve starts working under 31mph (50 km/h), and opens the second air inlet to reduce CO2 displacement.

AIR CHECK VALVE INSTALLATION Reverse the procedure for removal When installing, make sure all the connecting pipes are connected properly, and that they are not squeezed, bent, or clogged up.

26

TRANSMISSION COMPONENTS STARTING MECHANISM INSPECTION AND SERVICING The starting mechanism can be divided into two types: kick starting and electric starting.

KICK RETURN STARTING MECHANISM SPIRAL SPLINE TRANSFERRING STYLE STARTING MECHANISM The picture shows the structure of the spiral spline transferring style starting mechanism. 14

20

10 17

8

9

7

23

1 22

6

11 12

25

7 7 5

3

13

16

2

19

15

25

24 21

4

18

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.

Kick starter spring stopping plate Drive face Drive face boss Movable drive face comp. Weight roller set Ramp plate Slide piece Starting driver pulley Starter gear friction spring Starter idle gear comp. Starter idle shaft Starter idle spring Kick starter spindle comp.

14. Bush 15. Spindle bush 16. Kick starter spring 17. Special pin 18. Washer 19. Washer 20. Washer 21. Nut 22. Bolt 23. Roller 24. Face drive collar 25. Clip

SPIRAL SPLINE TRANSFERRING STYLE STARTING MECHANISM REMOVAL • Remove the left crankcase cover. • Remove the crankcase gasket and dowel pins. • Remove the movable driving plate (the whole set). • Remove the starting spindle washer.

27

‡ 5HPRYH WKH UHWXUQ VSULQJ VWRSSLQJ SODWH DQG UHPRYH WKH UHWXUQ VSULQJ ‡ 5HPRYH WKH ZKROH VWDUWLQJ OHYHU set ‡ 5HPRYH WKH VWDUWLQJ LGOH VKDIW

‡ 'LVDVVHPEOH WKH VWDUWLQJ VSLQGOH

‡ 'LVDVVHPEOH WKH VWDUWLQJ LGOH VKDIW

63,5$/ 63/,1( 75$16)(55,1* 67</( 67$57,1* 0(&+$1,60 ,163(&7,21 ‡ ,QVSHFW WKH starting spindle for abrasion or other damage. ‡ ,QVSHFW WKH VWDUWLQJ idle shaft for abrasion or other damage. ‡ ,QVSHFW WKH VWDUWLQJ spindle bushing and the starting idle shaft hole for abrasion or other damage

28

SPIRAL SPLINE

TRANSFERRING STYLE STARTING MECHANISM INSTALLATION Install according to the pictures .

• Assemble the starting idle shaft set. Before assembling, apply a little grease on the bore of the idle shaft.

• Assemble the starting spindle, the return spring and the spring holding pin. A little grease should be applied on the starting spindle where it is under stress .

• Align the idle shaft holding pin with the groove of the crankcase then insert. Before installing, apply a little grease on the groove of the rotary retaining spring on the idle shaft. The rotary retaining spring should be aligned with WKH VSHFL¿F JURRYH RI WKH FUDQNFDVH WR LQVWDOO • Align the scribing mark of the starting spindle with the punching mark of the idle shaft then mount the starting spindle. • Hook on the two ends of the return spring. • Install the return spring stopping plate.

• Install the crankcase dowel pin and gasket. • Install the driven belt and the driving plate. • Install the left crankcase cover and lock tightly. • Install the starting pedal. 29

ELECTRICAL STARTING SYSTEM STARTER MOTOR The starter motor is actually a direct current (DC) motor, and its structure is shown in the picture.

1. 2. 3. 4. 5. 6.

Outer Cover, Motor Rotor, Motor Base, Carbon Brush Plate, Positive Electrode Carbon Brush, Positive Electrode Carbon Brush, Negative Electrode

7. O-ring 8. O-ring 9. Bolt 10. Spring Washer 11. Washer 12. O-ring

13. Screw

STARTER MOTOR REMOVAL %HIRUH UHPRYDO ¿UVW VKXW Rff the main switch, and disconnect the battery connecting wire. Then press the starting button; at this time the starter motor should not run. Do this to insure safety. • Remove the starter motor lead wire clamp. • Remove the starter motor holding bolt, and remove the starter motor.

• Roll up the rubber wate-resistance cover, and remove the starter motor joint. • Remove the motor case bolt, the carbon brush seat, and the motor case, etc.

30

$50$785( ,163(&7,21 ‡ ,QVSHFW WKH DUPDWXUH VXUIDFH IRU XQHYHQ ZHDU GDPDJH RU EXUQV FKDQJLQJ FRORU ‡ :KHQ WKHUH DUH PHWDO ¿QHV DWWDFKHG WR WKH JDS RI WKH DUPDWXUH VXUIDFH XVH D FOHDQLQJ FORWK WR UHPRYH WKHP Do QRW XVH VDQGSDSHU WR JULQG the armature surface, nor ZDVK LW LQ DQ\ VROYHQW ZKLFK FDQ GLVVROYH RU GDPDJH LWV LQVXODWLRQ ‡ 0HDVXUH WKH FRQGXFWLQJ FRQGLWLRQ RI WKH DUPDWXUH FRLO DFFRUGLQJ WR WKH SLFWXUH on the immediate right ,W VKRXOG EH FRQGXFWLYH ‡ 0HDVXUH WKH FRQGXFWLQJ FRQGLWLRQ EHWZHHQ WKH DUPDWXUH FRLO DQG WKH DUPDWXUH DFFRUGLQJ WR WKH far-ULJKW SLFWXUH ,W VKRXOG EH QRQ FRQ GXFWLYH ,I LW¶V QRW LW VKRXOG EH UHSODFHG

&$5%21 %586+ ,163(&7,21 ‡ ,QVSHFW WKH LQVXODWLQJ FRQGLWLRQ EHWZHHQ WKH FRQQHFWLQJ ZLUH WHUPLQDO DQG WKH VWDUWHU PRWRU FDVH. IW VKRXOG EH QRQFRQGXF WLYH

‡ ,QVSHFW WKH FRQGXFWLQJ FRQGLWLRQ EHWZHHQ WKH FRQQHFWLQJ ZLUH WHUPLQDO DQG WKH FDUERQ EUXVK. IW VKRXOG EH FRQGXFWLYH 0HDVXUH WKH OHQJWK RI WKH FDUERQ EUXVK 5HSODFH LW LI LW H[FHHGV VHUYLFH OLPLW

‡ 0HDVXUH WKH LQVXODWLQJ FRQGLWLRQ RI WKH FDUERQ EUXVK EUDFNHt. IW VKRXOG EH QRQ FRQGXFWLYH; LI QRW LW VKRXOG EH UHSODFHG

‡ ,QVSHFW WKH QHHGOH EHDULQJ LQ WKH FDUERQ EUXVK EDVH; LW VKRXOG EH DEOH WR PRYH VPRRWKO\ ZLWK QR SOD\ ‡ ,QVSHFW WKH GXVW VHDO IRU ZHDU RU GDPDJH ‡ ,I GDPDJHG LW VKRXOG EH UHSODFHG 1

STARTER MOTOR INSTALLATION • Apply some oil on the dust seal. • Install the carbon brush on the carbon brush base. • Apply a little oil on the moving part of the armature ends. • Put the carbon brush into the bracket, and then install the carbon brush base.

Do not damage the contact area of the carbon brush and the armature. When installing, do not damage the lip of the dust seal. • Mount the new O-ring on the carbon brush base. • Install armature into starter motor case, making sure not to damage the carbon brushes. • Tighten motor case bolts. Make sure the starter motor case is free of metal particles because it is magnetic. %HIRUH LQVWDOOLQJ WKH VWDUWHU PRWRU RQ WKH YHKLFOH DIWHU DVVHPEOLQJ LW ¿rst connect the lead wires and check that the motor is running normally.

• Apply oil on the O-ring, and install the starter motor. • Tighten holding bolts.

32

REDUCTION MECHANISM The picture shows the structure of the reduction mechanism.

1. Starter reduction gear 2. Starter reduction gear shaft 3. Starting clutch gear comp. 4. Starting clutch outer comp. 5. Flange starting clutch 6. Starting clutch roller spring 7. Spring holder 8. Starter motor 9. Starter motor lead wire 10. Clamp 11. Clamp

12. Bolt 13. Nut 14. Washer 15. Dowel pin 16. Key woodruff 17. Roller 18. Needle bearing 19. O-ring 20. Screw 21. Bolt

REDUCTION GEAR INSPECTION • Remove the starting clutch. • Remove the reduction gear to inspect its wearing degree. • Measure the inner diameter of the reduction gear shaft. It should be replaced when the diameter is more than 10.05mm. • Measure the outer diameter of the reduction gear shaft. It should be replaced when the diameter is less than 9.94mm.

33

ENGAGING MECHANISM

STARTING CLUTCH REMOVAL • Remove the right crankcase cover. • Remove the left crankcase cover. • Hold the drive face with the universal set wrench. • Remove the starting clutch ¿xing nut. 1RWLFH WKDW WKH WKUHDG RI WKH ¿[LQJ QXW VKRXOG EH OHIW handed rotation. • Remove the starting clutch (the whole set).

STARTING CLUTCH INSPECTION ‡ ,QVSHFW WKH PRYHPHQW EHWZHHQ WKH FOXWFK DQG WKH GULYLQJ JHDU. The driving gear should smoothly turn clockwise, and should not move counterclockwise.

‡ ,QVSHFW WKH FRQWDFW VXUIDFH EHWZHHQ WKH GULYLQJ JHDU DQG WKH QHHGOH EHDULQJ for abrasion or other damage ,W VKRXOG EH replaced if the surface is damaged. • Measure the inner diameter of the driving gear ,W VKRXOG EH UH placed when the diameter is more than 32.06mm. ‡ ,QVSHFW WKH FRQGLWLRQ RI WKH QHHGOH EHDULQJ ,W VKRXOG EH UHSODFHG LI there is any damage. ‡ ,QVSHFW WKH FRQWDFW VXUIDFH between the outer clutch component DQG WKH UROOHr for abrasion or other damage. • Inspect the roller for injury. • Inspect the spring for distortion. ‡ ,I WKH GDPDJH LV VHULRXV LW VKRXOG EH UHSODFHG

• Measure the inner diameter of the ÀDQJH FOXWFK ,W VKRXOG EH replaced when the diameter is more than 27.94mm.

34

67$57,1* &/87&+ ,167$//$7,21 ‡ ,QVWDOO WKH VSULQJ WKH UROOHU DQG WKH WRS SLQ RQ WKH ERG\ RI WKH FOXWFK ‡ $OLJQ WKH GRZHO SLQ RQ WKH ÀDQJH FOXWFK ZLWK WKH KROH RQ WKH FOXWFK ERG\; WKHQ LQVWDOO ‡ $SSO\ VRPH WKUHDG ORFN RQ WKH RXWHU FOXWFK FRPSRQHQW EROW DQG WLJKWHQ ‡ $SSO\ VRPH RLO RQ WKH QHHGOH EHDULQJ DQG WKH GULYLQJ JHDU; WKHQ SXW WKH RXWHU FOXWFK FRPSRQHQW RQ ‡ $OLJQ WKH JURRYH RI WKH ZRRGUXII NH\ RQ WKH FUDQN DQG LQVWDOO WKH VWDUtLQJ FOXWFK ‡ $SSO\ VRPH RLO RQ WKH UHGXFWLRQ JHDU DQG WKH UHGXFWLRQ JHDU VKDIW; WKHQ LQVWDOO ‡ While hROGing WKH GULYH IDFH ZLWK WKH XQLYHUVDO ZUHQFK IDVWHQ WKH FOXWFK QXW 1RWLFH WKDW WKH WKUHDG RI WKH QXW VKRXOG EH OHIW KDQGHG URWDWLRQ ‡ ,QVWDOO WKH ULJKW FUDQNFDVH FRYHU ‡ ,QVWDOO WKH OHIW FUDQNFDVH FRYHU

&21752//,1* 0(&+$1,60 67$57(5 5(/$< ,163(&7,21 ‡ 7XUQ WKH PDLQ VZLWFK WR WKH ³21´ SRVLWLRQ. PUHVV GRZQ WKH VWDUWLQJ PRWRU EXWWRQ DQG OLVWHQ IRU D ³FOLFN´ VRXQG If clicking sound is not heard, IROORZ WKH EHORZ SURFHGXUHV WR LQVSHFW ‡ ,QVSHFW WR VHH LI WKH EUDNH VZLWFK for conductivity $W WKLV WLPH WXUQ WKH PDLQ VZLWFK RQ DQG KROG WKH EUDNH OHYHU 7KH EDWWHU\ YROWDJH VKRXOG EH DW YROWV ‡ 0HDVXUH WKH YROWDJH EHWZHHQ WKH LQOHW OLQH WKH JUHHQ \HOORZ OLQH VWDUWLQJ UHOD\ DQG WKH JURXQG ZLUH RI WKH ERG\ 7KH YROWPHWHU UHDGLQJ VKRXOG EH FORVH WR WKH PDJQLWXGH RI YROWDJH EHWZHHQ WKH WZR HQGV RI WKH EDWWHU\ ,I QRW WKHQ WKH EUDNH VZLWFK LWV ZLUH RU WKH ZLUH FRQQHFWRU LV GDPDJHG ‡ &KHFN the conductivity of the start button $W WKLV WLPH UHPRYH WKH VWDUWLQJ UHOD\ LQOHW OLQH WKH JUHHQ \HOORZ OLQH ‡ &RQQHFW WKH \HOORZ UHG OLQH ZLWK WKH JURXQG ZLUH DQG SUHVV WKH VWDUW EXWWRQ ,W VKRXOG EH FRQGXFWLYH EHWZHHQ WKH \HOORZ UHG OLQH DQG WKH JURXQG ZLUH ,I it is QRW FRQGXFWLYH, then WKH VWDUW EXWWRQ LWV ZLUH RU WKH ZLUH FRQQHFWRU LV GDPDJHG

35

‡ &KHFN WKH ZRUNLQJ FRQGLWLRQ RI WKH VWDUWLQJ UHOD\ $W WKLV WLPH UHPRYH WKH VWDUWLQJ UHOD\ ‡ &RQQHFW WKH & HQG and WKH ' HQG RI WKH VWDUWLQJ UHOD\ ZLWK WKH EDWWHU\ DQG WKH $ DQG % HQGs ZLWK WKH PXOWLPHWHU 7KH EDWWHU\ YROWDJH VKRXOG EH DW YROWV $W WKLV WLPH WKH PXOWLPHWHU VKRXOG LQGLFDWH D FRQGXFWLYH FRQGLWLRQ RU WKH VWDUWLQJ UHOD\ LV QRW JRRG

%(/7 '5,9(1 &97 0(&+$1,60 ,163(&7,21 $1' 6(59,&,1* *(1(5$/ ,1752'8&7,21 7KH EHOW GULYHQ &97 PHFKDQLVP LV PDGH XS RI WZR EHOW SXOOH\V WKH GULYH EHOW SXOOH\ DQG WKH GULYHQ EHOW SXOOH\ ZKRVH GLDPHWHU FDQ EH FKDQJHG DQG D QRWFKHG GULYHQ EHOW 7KH GULYLQJ EHOW SXOOH\ LV PRXQWHG RQ WKH HQJLQH FUDQNVKDIW DQG WKH GULYHQ EHOW SXOOH\ FRQQHFWV ZLWK WKH UHDU GULYHQ PHFKD QLVP

,WV EDVLF RSHUDWLRQDO SULQFLSOH LV WR UHDOL]H DXWRPDWLF &97 E\ WKH GL DPHWHU FKDQJHV WKH WUDQVPLVVLRQ UDWLR FKDQJHV RI WKH GULYLQJ DQG GULYHQ EHOW SXOOH\ :KHQ WKH GLDPHWHU RI WKH GULYLQJ EHOW SXOOH\ FKDQJHV IURP VPDOO WR ELJ SURSRUWLRQDOO\ WKH GLDPHWHU RI WKH GULYHQ EHOW SXOOH\ FKDQJHV IURP ELJ WR VPDOO EHFDXVH WKH SHULPHWHU RI WKH GULYHQ EHOW LV FRQ VWDQW . AW WKLV WLPH WKH VSHHG LQFUHDVHV Conversely, the speed decreases when the diameter of the driving belt pulley changes from big to small, and the diameter of the driven belt pulley changes proportionally from small to big.

36

7KH VWUXFWXUH RI WKH GULYLQJ EHOW SXOOH\ LV VKRZQ LQ WKH SLFWXUH

7KH SLFWXUH VKRZV WKH ZRUNLQJ WKHRU\ RI WKH GULYLQJ EHOW SXOOH\

7KH SLFWXUH VKRZV WKH VWUXFWXUH RI WKH GULYHQ EHOW SXOOH\ 7KH FOXWFK VKRZHG LQ WKLV SLFWXUH LV WKH DXWRPDWLF GU\ FHQWULIXJDO ZHLJKW FOXWFK

37

'5,9( %(/7 38//(< '5,9( %(/7 38//(< 5(029$/ ‡ 5HPRYH WKH OHIW FUDQNFDVH DLU SLSH ORFN EROW ‡ 5HPRYH WKH NLFN VWDUWHU DQG UHPRYH WKH OHIW FUDQNFDVH ¿[LQJ EROW 5HPRYH WKH OHIW FUDQNFDVH FRYHU 5HPRYH WKH JDVNHW DQG WKH GRZHO SLQ ‡ While holding WKH GULYH SODWH ZLWK D XQLYHUVDO ZUHQFK remove the QXWV DQG JDVNHW RQ WKH GULYH SODWH VKDIW 5HPRYH WKH GULYH SODWH ‡ 5HPRYH WKH GULYHQ EHOW IURP WKH GULYH SODWH

‡ 5HPRYH WKH PRYDEOH GULYH SODWH WKH ZKROH VHW

‡ 5HPRYH WKH UDPS SODWH

‡ 5HPRYH WKH FHQWULIXJDO UROOHUV

'5,9( %(/7 38//(< ,163(&7,21 ‡ ,QVSHFW for DEUDVLRQ RU GDPDJH WR WKH FHQWULIXJDO UROOHU ‡ 0HDVXUH WKH RXWHU GLDPHWHU RI WKH FHQWULIXJDO UROOHU 6HUYLFH /LPLW

PP

38

0HDVXUH WKH LQQHU GLDPHWHU RI WKH PRYDEOH GULYH SODWH 6HUYLFH /LPLW

PP

,QVSHFW LI WKHUH LV DQ\ DEUDVLRQ RU GDPDJH RI WKH GULYH SODWH KXE 0HDVXUH WKH RXWHU GLDPHWHU RI WKH GULYH SODWH KXE'V PRYDEOH surIDFH 6HUYLFH /LPLW

PP

'5,9( %(/7 38//(< ,167$//$7,21 $SSO\ VRPH JUHDVH HYHQO\ LQ WKH PRYDEOH GULYH SODWH 3XW WKH FHQWULIXJDO UROOHUV LQWR WKH PRYDEOH GULYH SODWH

,QVWDOO WKH UDPS SODWH

3XW WKH GULYH SODWH KXE LQWR WKH GULYH SODWH

,QVWDOO WKH PRYDEOH GULYH SODWH RQ WKH FUDQNVKDIW

39

‡ (QODUJH WKH GULYHQ SODWH EHOW JURRYH DQG PRXQW RQ WKH GULYHQ EHOW 0RXQW WKH RWKHU HQG RI WKH GULYHQ EHOW RQ WKH GULYH SODWH KXE ‡ 0RXQW WKH GULYH SODWH WKH GULYH SODWH ZDVKHU DQG QXW

‡ +ROG WKH GULYH SODWH ZLWK D PXOWLXVH KROGHU WR PDNH LW XQPRYDEOH ‡ $W WKH VDPH WLPH IDVWHQ WKH QXW RQ WKH VKDIW 'R QRW DOORZ DQ\ JUHDVH RU RLO WR JHW RQ WKH VXUIDFH RI WKH PRYDEOH GULYH SODWH DQG WKH GULYHQ EHOW

&/87&+ &/87&+ 5(029$/ ‡ 5HPRYH WKH OHIW FUDQNFDVH FRYHU ‡ 5HPRYH WKH GULYH SODWH DQG WKH GULYHQ EHOW ‡ +ROG WKH FOXWFK IULFWLRQ SODWH ZLWK D PXOWLXVH KROGHU DQG UHPRYH WKH QXW ‡ 5HPRYH WKH FOXWFK IULFWLRQ SODWH

&/87&+ ,163(&7,21 ‡ ,QVSHFW for DQ\ DEUDVLRQ RU GDPDJH RQ WKH FOXWFK IULFWLRQ SODWH ‡ 0HDVXUH WKH LQQHU GLDPHWHU RI WKH FOXWFK IULFWLRQ SODWH 6HUYLFH /LPLW

PP

‡ ,QVSHFW for DQ\ DEUDVLRQ RU GDPDJH RI WKH FOXWFK FHQWULIXJDO ZHLJK IULFWLRQ SLHFH ‡ 0HDVXUH WKH WKLFNQHVV RI WKH FOXWFK FHQWULIXJDO ZHLJKW IULFWLRQ SLHFH 6HUYLFH /LPLW

PP

&/87&+ ',6$66(0%/,1* ‡ ,I WKH FHQWULIXJDO ZHLJKW VHW QHHGV WR EH UHSODFHG \RX PXVW GLVDVVHPEOH WKH FOXWFK :KHQ WKH IULFWLRQ SLHFH LV ZRUQ replace it and the FHQWULIXJDO ZHLJKW VHW

0

• Remove the clutch friction plate. • Remove the whole clutch/driven plate set. • While compressing the driven pulley spring with the clutch spring compressor, remove the nut on the shaft. • Disassemble the clutch with the driven pulley. • Remove the circlip, and remove the connecting piece. • Remove the clutch centrifugal weight set and the spring.

CLUTCH INSTALLATION • Mount the clutch damper rubber onto the drive plate pin. • Mount the new clutch weight set and spring on the drive plate. • Install the connecting piece, the circlip, and the bottom plate. • Finally reverse the removal procedure for installation. To avoid damaging the spring when assembling the clutch and the driven plate, you must use a clutch spring compressor. The driven pulley must be free of grease.

41

'5,9(1 %(/7 38//(< '5,9(1 %(/7 38//(< 5(029$/ ‡ $IWHU UHPRYLQJ WKH FOXWFK IULFWLRQ SODWH UHPRYH WKH JXLGH SLQ WKH UROOHU DQG WKH PRYDEOH GULYHQ SODWH

‡ 5HPRYH WKH RLO VHDO RQ WKH PRYDEOH GULYHQ SODWH

'5,9(1 %(/7 38//(< ,163(&7,21 ‡ 0HDVXUH WKH IUHH OHQJWK RI WKH GULYHQ EHOW SXOOH\ VSULQJ 6HUYLFH /LPLW

PP

‡ ,QVSHFW for DQ\ DEUDVLRQ RU GDPDJH RQ WKH GULYHQ SODWH

‡ 0HDVXUH WKH RXWHU GLDPHWHU RI WKH GULYHQ SODWH SXOOH\ KXE 6HUYLFH /LPLW

PP

‡ ,QVSHFW for DQ\ DEUDVLRQ RU GDPDJH RI WKH PRYDEOH GULYHQ SODWH 6HUYLFH /LPLW

PP

‡ ,QVSHFW WKH JURRYH RI WKH JXLGH SLQ for wear

2

'5,9(1 3/$7( %($5,1* 5(3/$&(0(17 ,I WKH GULYHQ SODWH QHHGOH EHDULQJ RU WKH EDOO EHDULQJ DUH ORRVH GDPDJHG RU PDNH XQXVXDO VRXQGV WKH\ VKRXOG EH UHSODFHG ‡ 5HPRYH WKH QHHGOH EHDULQJ IURP WKH GULYHQ SODWH 7KH UHPRYHG EHDULQJ FDQQRW EH UHXVHG

‡ 5HPRYH WKH FLUFOLS IURP WKH GULYHQ SODWH ‡ 'ULYH WKH EDOO EHDULQJ RXW

7KH UHPRYHG EHDULQJ FDQQRW EH UHXVHG

‡ $SSO\ VRPH JUHDVH RQ WKH QHZ EDOO EHDULQJ ‡ 'ULYH WKH EDOO EHDULQJ LQWR WKH GULYHQ SODWH ZLWK LWV IURQW IDFH XSZDUGV ‡ 0RXQW WKH FLUFOLS ‡ $SSO\ JUHDVH HYHQO\ RQ WKH LQQHU ZDOO RI WKH GULYHQ SODWH 8VH WKH SUHVFULEHG JUHDVH ‡ 'ULYH LQ WKH QHZ QHHGOH EHDULQJ ZLWK LWV PDUN XSZDUGV 8VH WKH VSHFL¿F WRRO ‡ $SSO\ JUHDVH DURXQG WKH EHDULQJ

3

'5,9(1 %(/7 38//(< ,167$//$7,21 ‡ 5HPRYH WKH JUHDVH RQ WKH GULYHQ SODWH ‡ 0RXQW WKH RLO VHDO ‡ $SSO\ D OLWWOH JUHDVH RQ WKH 2 ULQJ ‡ 0RXQW WKH PRYDEOH GULYHQ SODWH LQWR WKH GULYHQ SODWH ‡ $IWHU DSSO\LQJ VRPH JUHDVH RQ WKH UROOHU and WKH JXLGH SLQ PRXQW WKHP LQWR WKH GULYHQ SODWH KROH ‡ ,QVWDOO WKH RLO VHDO FROODU ‡ 5HPRYH WKH H[FHVVLYH JUHDVH 'R QRW JHW JUHDVH RQ WKH PRYDEOH IDFHV RI WKH GULYHQ SODWH ‡ $VVHPEOH ZLWK WKH FOXWFK DQG LQVWDOO RQ WKH OHIW FUDQNFDVH

75$160,66,21 %(/7 75$160,66,21 %(/7 ,163(&7,21 ‡ 5HPRYH WKH OHIW FUDQNFDVH FRYHU ‡ ,QVSHFW WKH WUDQVPLVVLRQ EHOW for cracking and wear ‡ 0HDVXUH WKH ZLGWK RI WKH EHOW 6HUYLFH /LPLW

PP

‡ 5HSODFH WKH EHOW LI LWV ZLGWK LV OHVV WKDQ WKH DERYH OLPLW :KHQ UHSODFLQJ \RX PXVW XVH WKH 2(0 SDUW IRU FRUUHFW ¿W 6HH WKH GULYH SXOOH\ UHPRYDO DQG LQVWDOODWLRQ SURFHGXUH IRU WKH UHSODFHPHQW

44

5($5 75$160,66,21 0(&+$1,60 ,163(&7,21 $1' 6(59,&,1* 7KH VWUXFWXUH RI WKH UHDU WUDQVPLVVLRQ PHFKDQLVP LV VKRZQ LQ WKH IROORZLQJ SLFWXUH

75$160,66,21 &$6( 2,/ 5(3/$&(0(17 75$160,66,21 &$6( 2,/ ,163(&7,21 :KHQ LQVSHFWLQJ WKH RLO OHYHO RI WKH WUDQVPLVVLRQ FDVH XVH D ÀDW VXUIDFH DQG NHHS WKH ERG\ OHYHO ‡ &KHFN for oil leakage DURXQG WKH WUDQVPLVVLRQ FDVH ‡ $IWHU WKH HQJLQH VWRSV UHPRYH WKH WUDQVPLVVLRQ FDVH RLO OHYHO EROW ‡ 2EVHUYH WKH RLO OHYHO. TKH RLO OHYHO VKRXOG EH SDUDOOHO ZLWK WKH REVHUYLQJ KROH ‡ :KHQ WKH RLO OHYHO LV WRR ORZ DGG XQWLO WKH RLO ÀRZV IURP WKH OHYHO VFUHZ refill with the specified oil Always ‡ 0RXQW WKH WUDQVPLVVLRQ FDVH RLO OHYHO EROW DQG WKH ZDVKHU ,QVSHFW WKH EROW RLO VHDO WR VHH LI LW LV GDPDJHG

75$160,66,21 &$6( 2,/ 5(3/$&(0(17 ‡ 5HPRYH WKH WUDQVPLVVLRQ FDVH RLO OHYHO EROW ‡ 5HPRYH WKH RLO GUDLQ EROW WR GUDLQ WKH RLO ‡ 0RXQW WKH GUDLQ EROW DQG LWV RLO VHDO DQG IDVWHQ

45

• Supply the oil with the prescribed speci¿cation and oil level. • Mount the level bolt. • After replacing the oil, inspect for any oil leaks.

TRANSMISSION CASE TRANSMISSION CASE REMOVAL • Remove the driven belt pulley. • Drain out the oil in the transmission case. • Remove the drive sprocket. • Remove the bolt, and remove the transmission case cover. • Remove the gasket and the dowel pin. ‡ 5HPRYH WKH ¿QDO JHDr WKH ¿QDO JHDU VKDIW DQG UHPRYH WKH sub shaft/sub shaft gear.

TRANSMISSION CASE GEAR INSPECTION • Check the sub shaft/sub shaft gear for wear and other damage.

‡ &KHFN LI WKH ¿QDO JHDU and the ¿nal gear shaft for wear and other damage.

46

%($5,1* 21 7+( 75$160,66,21 &$6( &29(5 5(3/$&(0(17 :KHQ UHPRYLQJ RU LQVWDOOLQJ WKH EHDULQJ RQ WKH WUDQVPLVVLRQ FDVH FRYHU \RX PXVW XVH WKH VSHFL¿F WRRO VKRZQ LQ WKH SLFWXUH

‡ 3UHVV WKH GULYHQ EHOW SXOOH\ VKDIW RXW RI WKH WUDQVPLVVLRQ FRYHU

‡ 5HPRYH WKH RLO VHDO DQG GULYH RXW WKH EHDULQJ

‡ 5HPRYH WKH ¿QDO JHDU VKDIW EHDULQJ

‡ 5HPRYH WKH VXE VKDIW EHDULQJ

‡ 'ULYH LQ WKH QHZ ¿QDO JHDU VKDIW DQG EHDULQJ :KHQ GULYLQJ LQ WKH ¿QDO JHDU VKDIW EHDULQJ NHHS WKH EHDULQJ SDUDOOHO 7KH VDPH LV UHTXLUHG ZKHQ LQVWDOOLQJ WKH VXE VKDIW EHDULQJ DQG WKH GULYHQ SXOOH\ VKDIW EHDULQJ

‡ 'ULYH LQ WKH QHZ VXE VKDIW EHDULQJ

‡ 'ULYH LQ WKH GULYHQ SXOOH\ VKDIW EHDULQJ

47

%($5,1* 21 7+( /()7 &5$1.&$6( %2'< 5(3/$&(0(17 :KHQ UHPRYLQJ RU LQVWDOOLQJ WKH EHDULQJ RQ WKH OHIW FUDQNFDVH ERG\ \RX PXVW XVH WKH VSHFL¿F WRRO ‡ ,QVSHFW WKH EHDULQJ DQG RLO VHDO RQ WKH OHIW FUDQNFDVH IRU ZHDU RU GDPDJH ,I LW LV GDPDJHG LW PXVW WKHQ EH UHSODFHG ‡ 5HPRYH WKH RLO VHDO ‡ 'ULYH RXW WKH ¿QDO JHDU VKDIW EHDULQJ

‡ 5HPRYH WKH VXE VKDIW EHDULQJ

‡ 5HPRYH WKH GULYHQ EHOW SXOOH\ VKDIW EHDULQJ

‡ 'ULYH LQ WKH QHZ GULYHQ EHOW SXOOH\ VKDIW EHDULQJ

‡ 'ULYH LQ WKH QHZ VXE VKDIW EHDULQJ

‡ 'ULYH LQ WKH QHZ ¿QDO JHDU VKDIW EHDULQJ

48

‡ ,QVWDOO WKH GULYHQ EHOW SXOOH\ VKDIW RQ WKH WUDQVPLVVLRQ FDVH FRYHU

‡ 'ULYH LQ WKH WUDQVPLVVLRQ FDVH FRYHU RLO VHDO

‡ 0RXQW WKH VXE VKDIW VXE VKDIW JHDU DQG WKH ¿QDO JHDU VKDIW LQWR WKH OHIW FUDQNFDVH

‡ 0RXQW WKH ¿QDO JHDU RQ WKH ¿QDO JHDU VKDIW

‡ ,QVWDOO WKH QHZ GRZHO SLQ DQG JDVNHW ‡ ,QVWDOO WKH WUDQVPLVVLRQ FDVH FRYHU DQG EROW

‡ 0RXQW WKH GULYHQ SXOOH\ and WKH FOXWFK VHW

‡ 0RXQW WKH GULYH SXOOH\ WKH WUDQVPLVVLRQ EHOW DQG WKH OHIW FUDQNFDVH FRYHU ‡ )LOO WKH WUDQVPLVVLRQ FDVH ZLWK RLO

49

Electrical System CHARGING SYSTEM INSPECTION AND SERVICING ELECTRIC LEAKAGE TESTING • Turn the main switch to the “OFF” position. • Disconnect the negative ground wire from the battery. • Connect the positive end of the ammeter with the negative end of the battery. • Connect the negative end of the ammeter with the ground wire. • Test the electric leakage. In general, the number should be less than 1 m A; if it is unusual, check for is a short circuit of the main switch and the main wiring.

CHARGING STATUS INSPECTION • Install the fully charged battery. • Connect the voltmeter between the binding posts of the battery. • Remove the fuse, and connect the ammeter with two ends of the fuse. • Connect the tachometer to the engine (it’s not needed when there is rpm indicator on the vehicle). • Start the engine, and accelerate slowly 0 easure the charging voltage and current. Charging voltage (V) Charging current (A)

13.5 ~ 15.5 0.5

*Measuring condition: 5000 r/min If the voltage is not in the range of the above-speci¿ed value, please inspect the voltage regulator.

50

BATTERY The battery is an important component of the electric system. The battery used on the vehicle is a maintenance-free battery. For long periods of storage, the battery will discharge. It should be charged every 3 months. After 2 ~3 years of regular usage, the capacity of the battery will lessen and will need changing. Replace with the same type of battery.

BATTERY REMOVAL Shut down the main switch to make sure no electric current goes through the vehicle. • Disconnect the negative battery lead wire ¿rst. • Disconnect the positive battery. The disconnecting order cannot be reversed. When disconnecting the positive cable, do not touch the body of the vehicle with the removal tool, or it will short circuit and ignite gas that will damage the battery.

BATTERY INSTALLATION Connect the positive cable ¿rst, then connect the negative cable.

BATTERY OPEN-CIRCUIT VOLTAGE INSPECTION Disconnect the cable on the battery terminals. Disconnect the negative pole ¿rst, then the positive pole. Measure the voltage between the two poles of the battery. Full charging Under charging

51

13.1V 12.3V

BATTERY CHARGING • Lift the battery out of the vehicle. • Connect the positive pole of the charger with the positive pole of the battery. • Connect the negative pole of the charger with the negative pole of the battery. • Charge the battery for the charging time marked on the battery. Unless it is urgent, do not use fast charging. There should be no smoking or open ¿re near the battery when charging. At the beginning or the end of charging, turn off the FKDUJHU ¿UVW LQ RUGHU WR DYRLG WKH FRQQHFWLQJ SDUW DUFLQJ Measure the voltage 30 minutes after charging is ¿nished. It should reach the speci¿ed value, or recharging is needed.

Charging Current Charging Time

Normal Fast Normal Fast

0.7 A 3.0 A 5-10 hours 30 minutes 2SHQ FLUFXLW YROWDJH • 9

Charging Result

PRIMARY COIL The picture shows the structure of a common generator.

1. 3. 4. 5.

Cooling Fan Generator assembly Flywheel comp. Stator comp. Washer

6. Bolt 7. Nut 8. Bolt 9. Bolt

52

35,0$5< &2,/ ,163(&7,21 :KHQ WKH LQVSHFWLRQ ZRUN LV GRQH RQ WKH HQJLQH WKHUH LV QR QHHG WR UHPRYH WKH JHQHUDWRU ‡ 5HPRYH WKH FRUH FRQQHFWRU RI WKH JHQHUDWRU ‡ 0HDVXUH WKH UHVLVWDQFH YDOXH EHWZHHQ WKH ZKLWH ZLUHV RI WKH JHQHUDWRU DQG FRQQHFWLQJ ZLUH RI WKH YHKLFOH ERG\

6WDQGDUG YDOXH

a Â&#x; ƒ&

:KHQ WKH DFWXDO YDOXH LV PRUH WKDQ WKH VWDQGDUG YDOXH WKH FRLO VKRXOG EH UHSODFHG

*(1(5$725 5(029$/ $1' ,163(&7,21 *(1(5$725 5(029$/ ‡ 5HPRYH WKH FRROLQJ IDQ FRYHU EROW DQG VFUHZ ‡ 5HPRYH WKH FRROLQJ IDQ FRYHU ‡ 5HPRYH WKH FRROLQJ IDQ EROW DQG UHPRYH WKH FRROLQJ IDQ ‡ While hROGing WKH À\ZKHHO ZLWK D XQLYHUVDO KROGLQJ ZUHQFK UHPRYH WKH À\ZKHHO QXW

‡ 5HPRYH WKH À\ZKHHO ZLWK D À\ZKHHO SXOOHU DQG UHPRYH WKH VROLG NH\

3

‡ 5HPRYH WKH JHQHUDWRU ZLUH FRQQHFWRU ‡ 5HPRYH WKH JHQHUDWRU ZLUH KROGHU ‡ 5HPRYH WKH JHQHUDWRU FRLO EROW ‡ 5HPRYH WKH JHQHUDWRU ZLUH UXEEHU EXVKLQJ IURP WKH ULJKW FUDQNFDVH ‡ 5HPRYH WKH FRLO VHW 'R QRW GDPDJH WKH FRLO ZKHQ UHPRYLQJ

*(1(5$725 ,167$//$7,21 5HYHUVH WKH UHPRYDO SURFHGXUH IRU LQVWDOODWLRQ

:KHQ LQVWDOOLQJ WKH À\ZKHHO PDNH VXUH WKHUH DUH QR PHWDO SLHFHV VXFK DV EROWV RU QXWV DWWDFKed WR WKH LQQHU ZDOO RI WKH À\ZKHHO $IWHU WKH LQVWDOODWLRQ LV ¿QLVKHG VWDUW WKH HQJLQH WR LQVSHFW DQG DGMXVW WKH LJQLWLRQ WLPLQJ

5(*8/$7( 5(&7,),(5 0$,1 :,5,1* ± 68% (/(&75,& &,5&8,7 &21',7,21 ,163(&7,21 Perform WKH YROWDJH UHJXODWH UHFWL¿HU LQVSHFWLRQ SURFHGXUH LQ WZR VWHSV )LUVW LQVSHFW WKH PDLQ ZLULQJ ± VXE HOHFWULF FRQGLWLRQ DQG WKHQ LQVSHFW WKH YROWDJH UHJXODWRU 6HFRQG LQVSHFW RQO\ ZKHQ HQJLQH LV FROG ‡ 5HPRYH WKH FRUH FRQQHFWRU RI WKH UHJXODWH UHFWL¿HU ‡ 0HDVXUH WKH FRQGXFWLQJ VWDWXV EHWZHHQ WKH PDLQ ZLULQJ WHUPLQDOV DFFRUGLQJ WR WKH SUHYLRXV ZLU LQJ GLDJUDP

54

&RQQHFWLQJ W\SH

1RUPDO FRQGLWLRQ

%DWWHU\ WKH UHG ZLUH ± 9HKLFOH ERG\ &RQQHFWLQJ ZLUH WKH JUHHQ ZLUH ± 9HKLFOH ERG\ /LJKWLQJ ZLUH WKH \HOORZ ZLUH ± 9HKLFOH ERG\ UH PRYH WKH UHVLVWRU VLGH DXWR VWDUWHU SOXJ DQG WXUQ WKH OLJKWLQJ VZLWFK WR 2))

&KDUJLQJ ZLUH WKH ZKLWH ZLUH 9HKLFOH ERG\

%DWWHU\ YROWDJH YDOXH &RQGXFWLYH *HQHUDOO\ LV a Â&#x;

: :KLWH

: :KLWH

< <HOORZ

5 5HG

* *UHHQ

Â’ Â’ Â’

*HQHUDOO\ LV a Â&#x;

< <HOORZ

Â’ Â’ a .Â&#x;

5 5HG

a .Â&#x; Â’

* *UHHQ

Â’ a .Â&#x; Â’

Â’

5(*8/$7( 5(&7,),(5 ,163(&7,21 :KHQ WKH PDLQ ZLULQJ ± VXE HOHFWULF FLUFXLW FRQGLWLRQ LV QRUPDO LQVSHFW WKH UHJXODWH UHFWL¿HU ‡ &KHFN WKDW WKH UHJXODWH UHFWL¿HU SOXJ FRQWDFWV ZHOO ‡ 0HDVXUH WKH UHVLVWDQFH YDOXH EHWZHHQ HYHU\ UHJXODWH UHFWL¿HU WHUPLQDO ‡ ,I WKH UHVLVWDQFH YDOXH EHWZHHQ WKH WHUPLQDOV LV XQXVXDO UHSODFH WKH UHJXODWH UHFWL¿HU

5(6,6725 5(6,6725 5(6,67$1&( 9$/8( 0($685(0(17 0HDVXUH WKH UHVLVWDQFH YDOXH EHWZHHQ WKH UHVLVWRU ZLUH DQG WKH YHKLFOH ERG\ ,W LV QRUPDO ZKHQ WKH DFWXDO YDOXH LV LQ WKH UDQJH RI “ Â&#x; YDOXH PDUNHG RQ WKH GLDJUDP RU WKH UHVLVWRU. If QRW LW VKRXOG EH UHSODFHG

55

,*1,7,21 6<67(0 ,163(&7,21 $1' 6(59,&,1* 7KH FLUFXLW ZRUNLQJ SULQFLSOH LV VKRZQ LQ WKH SLFWXUH

,*1,7,21 7,0( ,163(&7,21 7KH &', LJQLWLRQ V\VWHP KDV DOUHDG\ EHHQ DGMXVWHG LQ WKH IDFWRU\ VR WKHUH LV QR QHHG WR UHDGMXVW LW ,I LQVSHFWLQJ LJQLWLRQ IXQFWLRQ LV QHFHVVDU\ XVH WKH IROORZLQJ VWHSV WR LQVSHFW LJQLWLRQ WLPLQJ ‡ 5HPRYH WKH LJQLWLRQ WLPLQJ KROH FRYHU RU UHPRYH WKH IDQ FRYHU ‡ 5RWDWH WKH JHQHUDWRU URWRU DQG DOLJQ WKH ³)´ PDUN RQ WKH URWRU ZLWK WKH FUDQNFDVH WLPLQJ LJQLWLRQ PDUN ‡ &OLS WKH LJQLWLRQ WLPLQJ LQGLFDWRU OLJKW ZLUH FOLS RQ WKH KLJK YROWDJH HQG RI WKH LJQLWLRQ FRLO ‡ 6WDUW WKH HQJLQH DQG OHW LW LGOH $W WKLV WLPH REVHUYH LI WKH PDUN RQ WKH FUDQNFDVH DOLJQV ZLWK WKH ³)´ PDUN RQ WKH URWRU A GLIIHUHQFH EHWZHHQ “ ƒ LQGLFDWHV FRUUHFW LJQLWLRQ WLPLQJ RQ WKH FRQWUDU\ LI LW LV more than “ ƒ the timing should be adjusted. ‡ 6ORZO\ LQFUHDVH WKH HQJLQH USP ZKHQ WKH PRGHO LQFUHDVHV WR U PLQ DW WKLV WLPH LI WKH PDUN RQ WKH FUDQNFDVH DOLJQV ZLWK WKH URWRU LJQLWLRQ DGYDQFH DQJOH PDUN WKH DGYDQFH DQJOH GHYLFH LV JRRG LI QRW LW VKRXOG EH DGMXVWHG RU UHSODFHG ‡ :KHQ DGMXVWLQJ WKH WULJJHU ZLQGLQJ FDQ EH ORRVHQHG WR DGMXVW WKH DQJOH EHWZHHQ LW DQG WKH LJQL WLRQ FKDUJLQJ FRLO WR DGMXVW WKH LJQLWLRQ WLPH

,*1,7,21 6<67(0 ,163(&7,21 ‡ :KHQ WKH VSDUN SOXJ GRHV QRW VSDUN ¿UVW LQVSHFW WKH ZLUHV. If WKH FRQQHFWLQJ SDUW LV ORRVH RU the contacts are bad, etc., IROORZ WKH HOHFWULF FLUFXLW DQG XVH WKH PHWKRG RI PHDVXULQJ WKH YROWDJH RI HYHU\ SRLQW WR determine WKH WURXEOH 3OHDVH UHIHU WR WKH SUHYLRXV SLFWXUH IRU WKH IROORZLQJ LQVSHFWLRQ ‡ 5HPRYH WKH ROG VSDUN SOXJ. IQVWDOO D QHZ RQH LI SOXJ LV EDG

56

,W LV LPSRUWDQW WKDW HYHU\ HOHFWULF FLUFXLW ZLUH FRQQHFWV FRUUHFWO\ ,W LV LPSRUWDQW WKDW WKH F\OLQGHU FRPSUHVVLRQ SUHVVXUH LV QRUPDO ‡ &RQQHFW WKH QHJDWLYH HQG RI WKH PXOWLPHWHU ZLWK WKH SRVLWLYH FRQQHFWLQJ LURQ RI WKH SULPDU\ LJQL WLRQ FRLO EODFN \HOORZ ZLUH ‡ 3UHVV WKH VWDUWLQJ EXWWRQ RU XVH WKH NLFN VWDUWHU DQG UHDG WKH YROWDJH YDOXH RQ WKH PXOWLPHWHU. TKH highest YROWDJH YDOXH VKRXOG EH DERYH 9 :KHQ PHDVXULQJ WKH YROWDJH GR QRW WRXFK WKH PHWDO SDUW RI WKH PXOWLPHWHU ZLWK ¿QJHU RU DQ HOHFWULF VKRFN FDQ RFFXU ‡ 5HPRYH WKH FRUH DQG FRUH FRQQHFWRUs RI WKH &', FRPSRQHQW ‡ &RQQHFW WKH SRVLWLYH HQG RI WKH PXOWLPHWHU ZLWK WKH LJQLWLRQ FKDUJLQJ FRLO EODFN UHG ZLUH HQG RI WKH FRUH FRQQHFWRU DQG WKH QHJDWLYH HQG ZLWK WKH JURXQG ZLUH HQG JUHHQ HQG RI WKH FRUH FRQQHFWRU ‡ 3UHVV WKH VWDUWLQJ EXWWRQ RU XVH WKH NLFN VWDUWHU DQG PHDVXUH WKH KLJKHVW YROWDJH RI WKH LJQLWLRQ FKDUJLQJ FRLO. IW VKRXOG EH PRUH WKDQ 9 ‡ :KHQ WKH KLJKHVW PHDVXUHG YROWDJH RI WKH LJQLWLRQ FKDUJLQJ FRLO LV QRW QRUPDO WKHQ GLVFRQQHFW WKH JHQHUDWRU FRQQHFWRU WR WDNH IXUWKHU PHDVXUHPHQWV ‡ ,I LW LV PHDVXUHG WKDW WKH &', FRPSRQHQW HQG LV DEQRUPDO and KRZHYHU WKH WHUPLQDO YROWDJH RI WKH JHQHUDWRU LV QRUPDO WKHQ WKHUH LV D EDG ZLUH RU EDG FRQQHFWLRQ ‡ :KHQ ERWK DUH QRW QRUPDO WKHQ the problem LV D EDG LJQLWLRQ FKDUJLQJ FRLO ‡ 5HPRYH WKH FRUH DQG FRUH RI WKH &', FRPSRQHQW ‡ &RQQHFW WKH SRVLWLYH HQG RI WKH PXOWLPHWHU ZLWK WKH WULJJHU ZLQGLQJ JUHHQ UHG ZLUH WHUPLQDO RQ WKH FRUH FRQQHFWRU DQG WKH QHJDWLYH HQG ZLWK WKH JUHHQ ZLUH WHUPLQDO RQ WKH FRUH FRQQHFWRU ‡ 3UHVV WKH VWDUWLQJ EXWWRQ RU NLFNVWDUWHU DQG PHDVXUH WKH KLJKHVW YROWDJH RI WKH WULJJHU ZLQGLQJ ZKLFK VKRXOG EH PRUH WKDQ 9 ‡ :KHQ WKH KLJKHVW PHDVXUHG YROWDJH RI WKH WULJJHU ZLQGLQJ LV QRW QRUPDO WKHQ UHPRYH WKH JHQ HUDWRU FRQQHFWRU DQG WDNH IXUWKHU PHDVXUHPHQWV ‡ ,I WKH PHDVXUHG WHUPLQDO YROWDJH RI WKH &', FRPSRQHQW LV QRW QRUPDO and WKH JHQHUDWRU WHUPLQDO YROW DJH LV QRUPDO WKHQ WKHUH LV D EDG ZLUH RU EDG FRQQHFWLRQ ‡ ,I ERWK DUH QRW QRUPDO WKHQ the problem LV D EDG WULJJHU ZLQGLQJ

,*1,7,21 &+$5*,1* &2,/ ‡ 5HPRYH WKH FRQQHFWRU RI WKH LJQLWLRQ FKDUJLQJ FRLO ZLUH ‡ 0HDVXUH WKH UHVLVWDQFH YDOXH EHWZHHQ WKH LJQLWLRQ FKDUJLQJ FRLO EODFN UHG ZLUH DQG WKH ERG\ JURXQG ZLUH 6WDQGDUG 9DOXH

a Â&#x; ƒ&

:KHQ WKH DFWXDO YDOXH LV PRUH WKDQ WKH VWDQGDUG YDOXH LW VKRXOG EH UHSODFHG

57

TRIGGER WINDING • Remove the connector of the trigger winding wire. • Measure the resistance value between the trigger winding (green/red wire) and the body ground wire. a Â&#x; ƒ&

Standard Value

When the actual value is more than the standard value, it should be replaced.

CDI COMPONENT 7KH &', FRPSRQHQW LQVSHFWLRQ LV VLPLODU WR WKH UHJXODU LQVSHFWLRQ 7KH &', component inspection is also divided into two steps: First inspect every wiring, winding or FRLO FRQQHFWHG ZLWK &', WKHQ LQVSHFW WKH &', FRPSRQHQW

REMOVE THE CDI COMPONENT. ‡ &KHFN WKH FRQQHFWRU IRU ORRVHQHVV RU HURVLRQ ‡ ,QVSHFW WKH FRQGXFWLRQ DQG WKH UHVLVWDQFH YDOXH RI WKH PDLQ VZLWFK WKH LJQLWLRQ FKDUJLQJ FRLO the trigger winding, and the ignition coil. When the main switch is in “OFF� position, it should be conducted. The resistance value of every coil should be the standard value. ‡ ,QVSHFW WKH UHVLVWDQFH YDOXH EHWZHHQ HYHU\ &', FRPSRQHQW WHUPLQDO ,I WKH DFWXDO YDOXH LV QRW LQ WKH UDQJH RI WKH YDOXH LQ WKH FKDUW WKHQ WKH &', FRPSRQHQW LV IDXOW\.

CDI COMPONENT SW (B/W) SW (B/W) EXT (B/R) 3& * 5

( * RU * : C ,*1 % <

0.5 ~ 50 10 ~ 1000 0.5 ~ 50 Â’

EXT (B/R) a Â’ 10 ~ 1000 0.5 ~ 50 Â’

3& * 5

a Â’ a Â’ 1 ~ 10 Â’

( * RU * :

a Â’ Â’ 1 ~ 100

,*1 % <

Â’ Â’ Â’ Â’

Â’

% %ODFN W :KLWH 5 5HG * *UHHQ <- <ellow 7KH &', FRPSRQHQW FDQ DOVR EH LQVSHFWHG DQG PHDVXUHG ZLWK WKH &', WHVWLQJ LQVWUXPHQW Please carefully read the instrument speci¿FDWLRQ WR NQRZ KRZ WR SURSHUO\ RSHUDWH ‡ &RQQHFW &', FRPSRQHQW ZLWK WKH VSHFLDO ZLUH RI WKH WHVWLQJ LQVWUXPHQW ‡ 2EVHUYH WKH VSDUN FRQGLWLRQ RQ WKH LQVWUXPHQW ZKHQ WKH VZLWFK LV WXUQHG RQ GLIferent positions (OFF, P, EXT 21 21

58

IGNITION COIL

IGNITION COIL REMOVAL

• Remove the spark plug cap. • Remove the primary ignition coil wire. • Remove the ignition coil-positioning bolt, and remove the ignition coil.

IGNITION COIL INSTALLATION • Reverse the removal procedure for installation. When installing, connect the black/yellow wire of the primary ignition coil with the black/yellow connector of CDI, and the green wire with the green connector of the CDI.

PRIMARY IGNITION COIL INSPECTION Standard Value

a .Â&#x; ƒ&

,I WKH UHVLVWDQFH YDOXH LV Â’ LW LQGLFDWHV WKH FRLO LV EDG DQG VKRXOG EH UHSODFHG

SECONDARY IGNITION COIL INSPECTION Install the spark plug cap, and measure the resistance value of the secondary ignition coil. Standard Value

a .Â&#x; ƒ&

If the resistance value is in the standard range, it is good; however Â’ LQGLFDWHV WKH FRLO LV EDG

Remove the spark plug cap, and measure the resistance value of the secondary ignition coil. Standard Value

a .Â&#x; ƒ&

If the resistance value is in the standard range, indicates it is good; however Â’ LQGLFDWHV WKH FRLO LV bad. The ignition coil also can be inspected and measured with the ignition testing instrument. Please operate properly according to the instructions. 6HW WKH PHDVXULQJ VZLWFK RI WKH LJQLWLRQ FRLO RQ WKH 9 SRVLWLRQ DQG FRQQHFW WKH LJQLWLRQ FRLO Turn the switch of the testing instrument to the “ONâ€? position. Observe the spark and inspect the spark situation of the ignition coil. If it is a normal consistent spark, it is good; if WKH VSDUN GRHV QRW Ă€DVK FRQVLVWHQWOy, it is not good.

SPARK PLUG • Clean the carbon around the spark plug to prevent it from dropping into the cylinder. Remove the spark plug. 59

When installing, connect the black/yellow wire of the primary ignition coil with the black/yellow connector of CDI, and the green wire with the green connector of CDI. &OHDQ WKH ¿Oth and carbon accumulation on the spark plug with a steel brush or a blade. • Inspect the spark plug gap in general it should be about 0.6 ~ 0.7mm. • When the carbon accumulation and wear of the spark plug are too severe, replace the spark plug. Replace with the spark plug of the same speci¿cation.

60

INDEX AIR ADJUSTING SCREW ADJUSTMENT AIR CHECK VALVE AIR CHECK VALVE INSTALLATION AIR CUT VALVE (ACV) AIR CUT VALVE INSTALLATION AIR CUT VALVE REMOVAL ARMATURE INSPECTION AUTOMATIC SIDE STARTER INSPECTION BATTERY BATTERY CHARGING BATTERY INSTALLATION BATTERY OPEN-CIRCUIT VOLTAGE INSPECTION BATTERY REMOVAL BEARING ON THE LEFT CRANKCASE BODY REPLACEMENT BEARING ON THE TRANSMISSION CASE COVER REPLACEMENT BELT DRIVEN CVT MECHANISM INSPECTION AND SERVICING

23 26 26 26 26 26 31 24 51 52 51 51 51 48 47 36

CAM CHAIN TENSIONER CAMSHAFT CAMSHAFT INSPECTION CAMSHAFT INSTALLATIION CAMSHAFT REMOVAL CAPACITIES CARBURETOR CARBURETOR IDLING ADJUSTMENT CARBURETOR INSTALLATION CDI COMPONENT CDI COMPONENT CHAIN ADJUSTRMENT CHARGING STATUS INSPECTION CHARGING SYSTEM INSPECTION CHARGING SYSTEM INSPECTION AND SERVICING

12 10 10 11 10 31 2 23 25 58 58 65 50 50 50

CHASSIS CHASSIS NUTS AND BOLTS CLUTCH

2 1 46

61

CLUTCH DISASSEMBLING CLUTCH INSPECTION CLUTCH INSTALLATION CLUTCH REMOVAL CONNECTING ROD END INSPECTION CONTROLING MECHANISM CRANK CONNECTING ROD MECHANISM CRANK CONNECTING ROD SET CRANKCASE AND CRANKSHAFT REMOVAL CRANKSHAFT AND CRANKCASE INSPECTION CRANKSHAFT AND CRANKCASE INSTALLATIION CV CARBURETOR CYLINDER CYLINDER INNER WAL WEAR INSPECTION CYLINDER REMOVAL DRIVE BELT PULLEY DRIVE BELT PULLEY INSPECTION DRIVE BELT PULLEY INSTALLATION DRIVE BELT PULLEY REMOVAL DRIVEN BELT PULLEY DRIVEN BELT PULLEY INSPECTION DRIVEN BELT PULLEY INSTALLATION DRIVEN BELT PULLEY REMOVAL DRIVEN PLATE BEARING REPLACEMENT ELECTRIC LEAKGAE TESTING ELECTRIC SYSTEM ELECTRICAL STARTING MECHANISM ENGAGING MECHANISM

40 40 41 40 4 36 4 5 6 7 7 22 3 3 3 38 38 39 38 42 42 44 42 43 50 50 30 33

ENGINE ENGINE COMPONENTS ENGINE COMPONENTS AND CRANK CONNECTING ROD ENGINE COMPONENTS INSPECTION AND SERVICING

6 6 6 6

ENGINE OIL FINAL GEAR OIL FLOAT CHAMBER FLOAT CHAMBER INSPECTION FLOAT CHAMBER INSTALLATION FLOAT CHAMBER REMOVAL FOAM FILTER MAINTENANCE

2 2 24 25 25 24 1

62

FUEL LEVEL INSPECTION FUEL SUPPLY SYSTEM INSPECTION AND SERVICING FUEL SWITCH (PETCOCK) GENERAL INTRODUCTION GENERAL INTRODUCTION GENERATOR INSTALLATION GENERATOR REMOVAL GENERATOR REMOVAL AND INSPECTION

25 22 1 18 36 54 53 53

IGNITION CHARGING COIL IGNITION COIL IGNITION COIL INSTALLATION IGNITION COIL REMOVAL IGNITION SYSTEM INSPECTION IGNITION SYSTEM INSPECTION AND SERVICING IGNITION TIME INSPECTION KICK RETURN STARTING MECHANISM LUBRICATION SYSTEM INSPECTION AND SERVICING MAIN WIRING – SUB ELECTRIC CIRCUIT CONDITION INSPECTION

57 59 59 59 56 56 56 27 18 54

MECHANISM INSPECTION MECHANISM INSPECTION AND SERVICING OIL PUMP ASSEMBLING OIL PUMP INSPECTION OIL PUMP INSTALLATION OIL PUMP REMOVAL OIL REPLACEMENT OIL SYSTEM INSPECTION AND REPLACEMENT OIL SYSTEM INSPECTION AND SERVICEING

28 3 21 20 21 19 19 19 50

PISTON PIN INSPECTION AND SERVICING PISTON RINGS INSPECTION AND SERVICING PISTON RINGS SET UP

4 4 5

63

PISTON SET PISTON SET INSTALLATION PRIMARY COIL PRIMARY COIL INSPECTION PRIMARY IGNITION COIL INSPECTION REAR TRANSMISSION MECHANISM INSPECTION AND SERVICING REDUCTION GEAR INSPECTION REDUCTION MECHANISM REGULATE RECTIFIER REGULATE RECTIFIER INSPECTION REMOVE THE CDI COMPONENT. RESISTOR RESISTOR RESISTANCE VALUE MEASUREMENT ROCKER ARM AND ROCKSHAFT ROCKER ARM AND ROCKSHAFT INSPECTION ROCKER ARM AND ROCKSHAFT INSTALLATION ROCKER ARM AND ROCKSHAFT REMOVAL ROTARY OIL PUMP

4 5 52 53 59 45 33 33 54 55 58 55 55 11 11 11 11 19

SECONDARY IGNITION COIL INSPECTION SPARK PLUG SPIRAL SPINE TRANSFERRING STYLE STARING MEACHANISM REMOVAL SPIRAL SPLINE TRANSFERRING STYLE STARTING MECHANISM SPRIAL SPLINE TRANSFERRING STYLE STARTING STARING CLUTCH INSTALLATION STARTER MOTOR STARTER MOTOR INSTALLATION STARTER MOTOR REMOVAL STARTER REPLAY INSPECTION STARTING CLUTCH INSPECTION STARTING CLUTCH REMOVAL STARTING MECHANISM INSPECTION AND SERVIVING

59 59 28 28 28 35 30 32 30 35 34 34 27

64

TIGHTENING TORQUE CHART TRANSFERRING STYLE STARTING MECHANISM INSTALLATION TRANSMISSION BELT TRANSMISSION BELT INSPECTION TRANSMISSION CASE TRANSMISSION CASE GEAR INSPECTION TRANSMISSION CASE OIL INSPECTION TRANSMISSION CASE OIL REPLACEMENT TRANSMISSION CASE OIL REPLACEMENT TRANSMISSION CASE REMOVAL TRANSMISSION COMPONENTS INSPECTION AND SERVICING TRIGGER WINDING VACUUM CHAMBER INSTALLATION VACUUM CHAMBER REMOVAL VALVE AND VALVE SEAT AIR IMPERMEABILITY INSPECTION VALVE AND VALVE SEAT LAPPING VALVE AND VALVE SPRING VALVE AND VALVE SPRING INSPECTION VALVE AND VALVE SPRING REMOVAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT VALVE GUIDE VALVE GUIDE INNER DIAMETER MEASUREMENT VALVE GUIDE REPLACEMENT VALVE MECHANISM INSPECTION AND SERVICING VALVE SEAT VALVE SEAT FINISHING VALVE SEAT TOUCHING POSITION INSPECTION VALVE SEAT WIDTH MEASUREMENT

65

1 28 44 44 26 26 45 45 55 57 27 58 24 23 17 17 13 13 13 2 9 14 14 14 8 15 15 16 15

Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.