Crushing Chamber Application Guide C5-1086:01ENG

Page 1

CRUSHING CHAMBER APPLICATION GUIDE SANDVIK CJ JAWS, SANDVIK CS CONES AND SANDVIK CH CONES


2

Crushing Chamber Application Guide


EHS

PUTTING YOUR SAFETY FIRST The mining and aggregate industries continue to demand even higher levels of safety and productivity. To meet these requirements, we work continuously to develop even safer products, and produce comprehensive manuals enabling safer and more effective use of our products. IT’S ALL ABOUT EVERYONE’S HEALTH Approximately 80–85 percent of crushing equipment accidents leading to Lost Time Injuries (LTIs) occur during maintenance of the equipment. Helping you ensure a safer workplace and healthier workforce is of the utmost importance to us. The well-being of any person coming into contact with our equipment is paramount. Therefore, we strive to identify and assess potential risk factors that could threaten the health of you and your employees. All of the products in this guide are designed to meet safety requirements.

DRESS RIGHT FROM HEAD TO TOE You must wear appropriate personal protective equipment (PPE) at all times. This is what we strongly recommend to help avoid injury: –– Safety helmet –– Hearing protection –– Safety glasses –– Protective high-visibility clothing –– Respiratory protection –– Safety boots –– Any site-specific PPE as required

BE AWARE OF ALL SAFETY PROCEDURES We ask that you start by obeying all instructions given. Safe work procedures should incorporate inspection before the machine operates, and also through regular monitoring based upon local conditions, as well as safety and hazard management systems. Workers should be provided with safety information, instruction and training on transportation, installation, operational care and disposal of the crusher wear parts.

DO A RISK ANALYSIS BEFORE YOU START Pay attention to safety when planning all of your work. Before you start, always take your time to go through all operations. Identify any potential risks and take appropriate measures to avoid them. If necessary, seek expert advice on how to help minimize risks. Finally, make sure that you have the right resources to perform all tasks in the safest manner possible.

For full list of safety procedures, always refer to the crusher’s Operator and Maintenance manuals. PERSONAL PROTECTION Sandvik strongly recommends that personal protective equipment is always worn when working in the vicinity of the equipment. Sandvik strongly recommends using a safety harness when working above, inside or under the equipment.

“TAKE FIVE” TO IDENTIFY HAZARDS A great safety tool to use before you start working is our app: “Sandvik Mining Take Five”. The app consists of a simple, step-bystep checklist with five questions that you should ask yourself to identify potential hazards. The app is free to download for smartphones and tablets, both on the App Store and Google Play.

Crushing Chamber Application Guide

33


HOW TO WORK WITH SAFETY IN MIND PERSONNEL All work on the equipment must be carried out by trained personnel. “Trained� means that the person in question has been given practical instruction by an authorized person on how the various tasks are to be carried out. PREPARATIONS Falling stones Clear the feed arrangement from process material before any maintenance work is carried out inside or below the crusher to prevent stones from falling down. Power off Always switch off power and lock out the equipment (so that it cannot inadvertently be switched on) before any maintenance work is started. Also ensure that it is not possible for anyone else to switch the power on while maintenance work is being carried out. Avoid staying on the equipment, unless necessary for maintenance work. Machine access Every machine requires access for personnel who carry out inspections and/or maintenance work. Suitable

4

Crushing Chamber Application Guide

access platforms and guard rails shall be installed. Walkways, stairs and ladders must be designed in accordance with applicable regulations. OPERATION MAINTENANCE Hanging load Only personnel with adequate lifting training are permitted to perform lifting operations. Check all the lifting equipment for wear and damage. Ensure that the lifted parts cannot be inadvertently moved or lowered. Never work or stand underneath a crane that is lifting material. Keep a safe distance from hanging load. Grinding/Welding Some maintenance procedures such as grinding and welding will produce hazardous substances and particles. These can be inhaled or swallowed, or come into contact with the skin or eyes. Wear protective gloves, protective clothing and eye protection. Always use a respirator when welding or torch cutting manganese steel. Welding on the crusher is only permitted when and as described in the manual. For all other welding operations


on the crusher, local service personnel must be consulted. If welding an item to the crusher, the grounding cable must be attached to the item itself. If a crusher component is to be welded, the grounding cable should be attached as close to the welding area as possible. Noise During crusher maintenance, significant noise is generated (e.g. hammering = metal-to-metal contact, grinding). Suitable hearing protection is recommended. Skin irritation After setting, epoxy plastic is physiologically harmless. Before setting, however, epoxy resin and hardener can cause skin irritation and allergic-contact eczema. Dust Crushing rock or ore generates dust. Some dust is hazardous if inhaled. Use of a suitable PPE is always recommended. Tool Inspection Inspect tools before use and at regular intervals. If they are loose, dull, bent, cracked, burred or otherwise unsuitable, DO NOT USE THEM. Replace them. Lifting Use safe lifting practices while working with heavy items. Consider your body position, the awkwardness of the item and its weight. Are two people required for the job or is a lifting device necessary? Are you using the correct Sandlock lifting tool?

SANDLOCK™ LIFTING TOOLS A wide series of safety lifting tools for our CH cone crusher models has been specifically designed for Sandvik mantles and concaves. The Sandlock lifting tools are CE marked and are designed to simplify maintenance routines and improve Environment, Health and Safety (EHS) aspects when changing mantles and concaves.

Crushing Chamber Application Guide

5


EHS

AT YOUR SERVICE, AROUND THE WORLD THE SANDVIK GROUP Every crushing and screening product is preceded by extensive research and development, and backed with application expertise, a worldwide service network, offering on-site service, training and round-the-clock support. We have a tradition of localization and a conviction that there can be no substitute for direct service and direct contact with you. Our service-oriented, global organization is well developed and contains more than 3,500 service technicians located strategically around the world. Sandvik was established in 1862; today, it is a global industrial group with advanced products and world-leading positions in selected areas. In 2017, we had approximately 43,000 employees and sales of SEK 91 billion in more than 150 countries within continuing operations. Our operations are based on unique expertise in materials technology, and significant insight into your processes.

We are a leading global supplier of equipment, tools, service and technical solutions for the mining and construction industries. Application areas include rock drilling, rock cutting, crushing and screening, loading and hauling, tunneling, quarrying, and breaking and demolition.

6

Crushing Chamber Application Guide

Our goal is to actively contribute to improving your productivity and consequently your profitability. Our products and services provide maximum value to you in terms of performance, quality, speed, safety, flexibility and not least total economy. Successful development is a result of our goal-oriented investment in research, development and quality assurance. We invest over SEK 3 billion annually and have more than 2,700 employees working in these areas. Many of them are specialists with advanced educational backgrounds and skills.

SANDVIK MINING AND ROCK TECHNOLOGY Sandvik Mining and Rock Technology is a business area within the Sandvik Group. We are a leading global supplier of equipment, tools, service and technical solutions for the mining and construction industries. Application areas include rock drilling, rock cutting, crushing and screening, loading and hauling, tunneling, quarrying, and breaking and demolition. In 2017, sales were approximately SEK 37 billion with about 15,000 employees in continuing operations. WHICH INVENTION CAN SOLVE YOUR NEEDS? Through close customer collaboration, we develop products that are genuinely needed and we have some 8,000 active patents. We also study trends to ascertain what customer needs will be in the future. We are continuously working on unique solutions that help our customers improve their productivity and safety. The spirit of innovation and involvement runs through every product.


Our worldwide business activities are conducted via representation in more than 150 countries.

Crushing Chamber Application Guide

77


8

Crushing Chamber Application Guide


TABLE OF CONTENTS EHS 3 PUTTING SAFETY FIRST 3 HOW TO WORK WITH SAFETY IN MIND 4 AT YOUR SERVICE, AROUND THE WORLD

6

APPLICATION SEGMENTS

10

SERVICE AGREEMENTS FOUR REASONS WHY

12 13

CRUSHING CHAMBER SOLUTIONS 14 PREMIUM CRUSHING CHAMBER SOLUTIONS 16 ALLOYS 18 CUSTOMIZED CRUSHING CHAMBERS 22 SANDLOCK TM LIFTING TOOLS 23 JAW GUIDE 25 BASIC CRUSHING PRINCIPLES 26 BASIC PRINCIPLES OF THE SANDVIK CJ JAW CRUSHER 28 SELECTION OF JAW PLATES 30 JAW PLATE SELECTION BASED ON ROCK AND FEED CHARACTERISTICS 30 JAW PLATE PATTERNS - FIXED PLATE 31 ONE, TWO, THREE OR SIX-PIECE JAW PLATES 32 WEAR IN PRACTICE 33 CJ211 (J11) 34 CJ409 (JM907) 35 CJ411 (JM1108) 36 CJ412 (JM1208) 37 CJ612 (JM1211) 38 CJ613 (JM1312) 39 CJ615 (JM1511) 40 CJ815 (JM1513) 41 CS (S-TYPE) CONE GUIDE 43 BASIC CRUSHING PRINCIPLES 44 BASIC PRINCIPLES OF THE SANDVIK CS CONE CRUSHER 45 GETTING THE RIGHT FIT 46 SANDVIK CS CRUSHER DESIGN FEATURES 47 CRUSHING CHAMBER - CS CONE RANGE 48 CS420 (S2800) 51 CS430 (S3800) 52 CS440 (S4800) 54 CS550 56 CS660 (S6800) 57

CH (H-TYPE) CONE GUIDE 61 BASIC CRUSHING PRINCIPLES 62 BASIC PRINCIPLES OF THE SANDVIK CH CONE CRUSHER 63 GETTING THE RIGHT FIT 65 SANDVIK CH CRUSHER DESIGN FEATURES 66 STANDARD CRUSHING CHAMBERS - CH CONE RANGE 68 PREMIUM CRUSHING CHAMBER SOLUTIONS 74 CH420 (H2000) 76 CH430 (H3800) 80 CH440 (H4800, H4000) 86 CH540 92 CH550 96 CH660 (H6800) 100 CH860i (CH860) 108 CH865i (CH865) 112 CH870i (CH870, H7800) 116 CH890i (CH890, CH880, H8800) 124 CH895i (CH895, CH880, H8800) 130 APPLICATION AND TROUBLESHOOTING IMPORTANCE OF CRUSHING CHAMBER SELECTION - CONE CRUSHERS COMMON FEED ARRANGEMENT PROBLEMS OPTIMAL FEED ARRANGEMENT WHEN TO CHANGE LINERS - CONE CRUSHERS UNWANTED WEAR PATTERNS - CONE CRUSHERS UNWANTED WEAR PATTERNS - JAW CRUSHERS

137 138 140 142 144 147 150

SAMPLING METHODOLOGY 153 SAMPLING IN COMMINUTION PLANT PRACTICES 154 TAKING A BELT-CUT: A FIVE-STEP PROCESS 155 SAMPLING PROTOCOL 159 CONVERSION TABLES

160

NOTES 161

Crushing Chamber Application Guide

9


APPLICATION SEGMENTS

APPLICATION SEGMENTS QUARRYING Aggregates are produced for a few different purposes, mainly as crushed rock, concrete, and asphalt. Demands on size, shape, and strength are placed on the produced material, depending on the application. The size of premium product in a crushing and screening plant normally ranges from 2-63 mm. Quarrying is different than mining in that the material produced from the crushing and screening plant requires no further size reduction. MINING THREE-STAGE CRUSHING & SCREENING Conventional crushing and screening circuits provide crushed products for further processing, such as grinding or heap leaching, for either milling or other beneficiation. Traditionally, rod milling and ball milling are the next step after staged crushing, but are no longer used in plant practices due to their higher operational cost and lower energy efficiency. The technology is only used in older existing installations and would not be chosen for a new greenfield project. More efficient crushers, such as staged crushing and ball milling, are now available and commonly used. The feed size to ball mill normally ranges from 6-12 mm; however, in some practices, coarser particles up to 18 mm are fed to the ball mills. PEBBLE CRUSHING IN SEMI-AUTOGENOUS (SAG) AND AUTOGENOUS (AG) MILLING CIRCUITS Autogenous Grinding (AG) is the process of milling primary crushed ore, approximately minus 300 mm in size, stone against stone in a big AG mill. The AG process only works with ores that have suitable mechanical properties. Bigger stones must be able to break smaller stones; therefore, special size distribution of the feed is needed. In plant practices, ores that are too soft (low competent) or too hard (high competent) are not suitable for the AG process. Semi-Autogenous Grinding (SAG) was introduced to accommodate those ores by adding grinding media (big steel balls, normally 125 mm in diameter) to the AG mill, converting it to a SAG mill. Often the SAG and AG processes face difficulties in maintaining the intended production rate and energy consumption. Some of the stronger stones, mainly medium-sized stones and pebbles ranging in size from 20-70 mm, build up, affecting the performance of a SAG or AG mill. To improve the SAG/AG milling performance and reach requirements for downstream fine grinding processes, a pebble crusher is added to the circuit to crush down the 20-70 mm pebbles. A grate in the SAG controls the upper size; the pebble screen controls the smaller. Crushed material can be sent back to the SAG or directly to the ball mill. If sent to the ball mill, the pebble crusher needs to work in closed circuit with a screen to achieve the necessary small feed size. HEAP LEACHING Heap leaching is a chemical or biological metal extraction method. The size of material sent to the heaps depends on the ore and targeted recovery rate. Lower grade ore might not economically merit more than primary crushing — or, in some cases, may merit no crushing at all. Usually, material is crushed to -6 mm, -25 mm or even -50 mm. Therefore, the crushing circuits can be quite different from case to case. Sometimes, the ore creates a lot of fines when crushed down. In these situations, there can be problems with the liquid penetration in the heaps. To reduce the amount of fines, agglomeration is added to the process. LUMP ORE Lump ore is used in the blast furnace process to achieve a good gas flow. To get a maximum amount of the desired lump ore fraction, crushers are set for a low reduction ratio. Usually, three crushing stages are used to produce highgrade iron ores. First, the fines (normally -8 mm) are screened away. Then a fraction of lump ore between 8 mm and 30 mm or 5 mm and 16 mm is produced. (CNS image of a guy holding a stone in his hands)

10

Crushing Chamber Application Guide


Crushing Chamber Application Guide

11


SERVICE AGREEMENTS

SERVICE AGREEMENTS THE SERVICES AND PARTS YOU NEED – WHEN YOU NEED THEM Our five proactive service agreements cover the entire lifecycle of your crushing and screening plant – from precommissioning and ramp-up to full operation. Through our highly-trained expert engineers, our service agreements are designed to provide you with safer operations, low operating costs and long service life, unlocking the full potential of your crushing plant 365 days a year. CONDITION INSPECTIONS Comprehensive inspections from a certified Sandvik service engineer covering the most critical points. You get continuous status reports on your equipment health, improving reliability and saving costs by avoiding expensive failures. EXTENDED WARRANTY Get the extra protection you need for your equipment. Built on the Condition Inspection offer, this program goes beyond maintenance recommendations; it gives you 85% coverage on the list price of major components*. Designed to keep your equipment running smoothly for longer, a Sandvik Extended Warranty program gives you peace of mind. ADVISORY SERVICES Minimize networking capital and ensure you have the right inventory with regular parts planning. Built on Condition Inspection, our Advisory Services program combines regular inspections with comprehensive parts and maintenance planning, giving you up to 15% more machine availability. PRODUCTIVITY SERVICES Extract the most out of your equipment and enjoy an up to 10% increase in productivity. Our most comprehensive service package gives you increased uptime, profit and complete peace of mind in a risk-controlled operation. Ensure consistent, high-volume performance and get more of the product you want with the optimization of all crushing equipment parameters. RAMP-UP SERVICES Quicker ramp-up means quicker profits. Our Ramp-Up Services program helps you get your production up and running as fast as possible, adding 2-5 weeks of additional production time as compared to a “do it alone” approach. Extract the most out of your new equipment and get process verification to optimize your productivity.

PERFORMANCE RELIABILITY CONDITION INSPECTIONS

√ √ √ √

Periodic inspections Trend analysis Clear documentation On-site troubleshooting

PROTECTION EXTENDED WARRANTY

√ √ √ √ √ √

Component coverage OEM parts Periodic inspections Trend analysis Clear documentation On-site troubleshooting

AVAILABILITY ADVISORY SERVICES

√ Annual audit √ Training sessions √ Parts planning √ Maintenance planning √ Periodic inspections √ Trend analysis √ Clear documentation √ On-site troubleshooting

PERIODIC INSPECTIONS

* Terms and conditions apply

12

Crushing Chamber Application Guide

PRODUCTIVITY SERVICES √ Process verification √ Crushing circuit optimization √ Crushing chamber optimization √ Component coverage √ OEM parts √ Annual audit √ Training sessions √ Parts planning √ Maintenance planning √ Periodic inspections √ Trend analysis √ Clear documentation √ On-site troubleshooting

FASTER START-UP RAMP-UP SERVICES √ Process verification √ Crushing circuit optimization √ Crushing chamber optimization √ OEM parts √ Annual audit √ Training sessions* √ Parts planning* √ Maintenance planning* √ Periodic inspections √ Trend analysis √ Clear documentation √ On-site troubleshooting * pre-commissioning & year 1


FOUR REASONS WHY • • • •

Experts offer dedicated knowledge and experience in OEM equipment and the applications surrounding it Proven and globally established optimization procedures use thousands of applications as a benchmark to find you the most efficient solutions Customized training sessions and frequent on-site support foster the transfer of knowledge to staff and develop skills Clear guidance leads you toward higher reliability, availability and productivity, ensuring lower operating costs

CRUSHING CHAMBER OPTIMIZATION Crushing Chamber Optimization is a tailored service for customers looking for ways to change, optimize or enhance the performance of their crushing process. It is a continuous improvement program since the characteristics of the feed material or the process itself may vary. Depending on your needs, we can help set goals like longer wear life, higher throughput capacity, finer material or better particle shape. And if you have a Ramp-Up or Productivity Service agreement, this service is included. The first step of the process is identifying your needs with the help of a local Sandvik specialist. Then a global expert – with the help of the local specialist – will collect the necessary data for analysis. This could include parameters like feed gradation, material samples, power draw, wear patterns and crusher settings. Then we analyze your data using our global Sandvik benchmark experience and optimization software to help determine your optimal crusher configuration and settings, all of which are tailored to your application and targets. We ensure that you not only have the most efficient crushing chamber, throw and crusher settings, but that you have the right feed solutions to minimize segregation and achieve optimal feed levels. This is how we help you reach your targets and maximize productivity.

Contact your local Sandvik rep to learn more about our Service Agreements and how they can benefit you.

Crushing Chamber Application Guide

13


CRUSHING CHAMBER SOLUTIONS

CRUSHING CHAMBER SOLUTIONS

PRODUCTIVITY SOLUTIONS YOU CAN COUNT ON Sandvik offers a wide range of standard, premium and customized crushing chamber solutions that are created based on your needs, and deliver consistently high availability and reliability. These solutions offer significant productivity gains and safety improvements in your crushing operations, and improve your bottom line.

Our innovative Optiagg solution is our latest premium offering, delivering predictable and measurable improvements per your desired output (whether it is a P80 or a target fraction) using our applied simulation tool. This gives you the choice to reduce fines production or increase the reduction ratio; whichever makes your operations more profitable.

Sandvik works closely with you to find the best solution for your needs – in terms of performance and safety, as well as application and material feed properties. Using our application expertise, we work with you to find your perfect fit.

No matter the Sandvik crusher model you have, we have quality OEM parts that are designed to fit your machine perfectly. Tested to the extremes, they will give you more working time and greater efficiency than non-original parts.

We offer standard crushing chambers – which are a combination of mantles and concaves – and jaw plates based on our M1 alloy. Over the years, we have engineered newer alloy mixes like M2, M7, M8 and M9 with a higher resistance to abrasive rock, but a lower resistance to shock and impact. Our premium M9 mix offers up to 20% longer lifetime compared to M1, resulting in more uptime and lower operating costs. We have also added new, patented design patterns that are unique to Sandvik. The Flexifeed mantle increases uptime with up to 20% longer lifetime, while our High Reduction concave has been proven to offer up to 10% more final product, when they are compared to a correctly configured standard chamber. We have also developed Oversize Breakers for our CH range of crushers that increase the allowable top size in finer chambers. 14

Crushing Chamber Application Guide

Sandvik has the application expertise to increase the product quality in your crushing and screening operations, as well as optimize your profits and productivity 365 days a year. TOTAL COST OF OWNERSHIP When Total Cost of Ownership (TCO) is taken into account, our Sandvik wear parts can generate significant savings and increase your profits. The longer lifetime of our Sandvik wear liners means that fewer sets need to be purchased, machine uptime is higher, and fewer liner changes are needed during maintenance. And when Sandlock lifting tools are in place, you can save up to one hour per liner change.


WHAT IS A CRUSHING CHAMBER? The crushing chamber is the geometric profile between two wear liners. One liner is static while the other is moving. In a cone crusher, the moving part is the mantle – which sits on the main shaft – and the fixed liner is the concave inside the top shell. In a jaw crusher, both liners are called jaw plates with one fixed plate and one moving plate. WEAR IS UNAVOIDABLE Wear is the removal of particles from the surface and is an inevitable occurrence in crushing chambers. The crushing force and the rock characteristics will wear down all liners over time, but we have engineered ours to offer a longer lifetime and a higher wear resistance.

ABRASION INDEX (AI)

DESCRIPTION OF THE WEAR

ROCK EXAMPLES

< 0.1

Very low wear

Limestone, Dolomite

0.1-0.2

Low wear

Hard Limestone

0.2-0.4

Intermediate wear

Basalt, Diabase, Gabbro

0.4-0.6

Normal-medium wear

Granite, Gneiss

0.6-0.8

High wear

Porphyry, Quartzite

> 0.8

Extremely high wear

Sandstone, Iron Ore

High

Abrasion is the main cause of liner wear. Friction is created between moving particles or rocks that causes mechanical scratching, grinding and gouging. The Abrasion Index (AI) measures the abrasive characteristics for different types of rock, and we can personally assess the abrasiveness of different feed materials at our Rock Processing Test and Research Center in Svedala, Sweden.

Wear loss

Based on our testing methodology, the following chart indicates the abrasiveness of different rock types and the wear on manganese steel liners in jaw and cone crushers.

Abrasion index

Low

High

Crushing Chamber Application Guide

15


CRUSHING CHAMBER SOLUTIONS

PREMIUM CRUSHING CHAMBER SOLUTIONS PREMIUM CHAMBER DESIGNS Sandvik offers an innovative range of premium chamber solutions that are created based on your needs, and deliver consistently high availability and reliability. These innovative and patented solutions offer significant productivity gains and safety improvements in your crushing operations, and improve your bottom line. FLEXIFEED MANTLE Our Flexifeed (FF) mantle – or moving liner – is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. Created for crusher models CH420 to CH890i, it has a varying feed opening that is ideal if the crusher feed is not calibrated.

OVERSIZE BREAKER MANTLE Our Oversize Breaker (OB) mantle is engineered for tertiary crushing applications. Created for crusher models CH865i, CH870i and CH895i, it has a varying feed opening that is ideal if the crusher feed is not calibrated. It also increases the allowable top size in finer chambers and helps to prevent bridging from oversized rock. It is based on our EF-mantle profile design and you can use it with the following concaves: F, EFX, EF, EEF.

You can use it with the following concaves: EC, C and MC.

FLEXIFEED

16

Crushing Chamber Application Guide

OVERSIZE BREAKER


OPTIAGG MANTLES – PART OF OUR OPTIAGG SOLUTION* Optiagg is a high-efficiency mantle delevoped for specific customer values, like reduced fines production or increased size reduction. Three to six wedges have been specially designed on the mantle to alter the crushing chamber design to reduce interparticle breakage or to change how crushing forces are generated within the crushing chamber. Depending on your application, you can either reduce fines production or increase the reduction ratio. The choice is yours and the real difference is the applied computer modeling and analysis, which is necessary to find the optimal premium crushing chamber solution for your needs. Designed for tertiary or final crushing stages, our Optiagg solution for crusher models CH430, CH440 and CH660 delivers predictable, measurable improvements per your desired output (whether it is a P80 or a target fraction) using our applied simulation tool. This gives you the decision power to reduce fines production or increase the reduction ratio.

OPTIAGG S

Optiagg L mantle, with its 3-wedge design, can be used with concaves MC, M and MF. Optiagg S mantle, with a 6-wedge design, can be used with concaves M, MF and F. * The Sandvik computer modeling and analysis tool must be used to determine the correct crushing chamber setup. HIGH REDUCTION CONCAVE Our High Reduction concave – or fixed liner – has a unique shelf design that increases the crushing chamber pressure in crusher models CH660, CH865i, CH870i and CH895i. This patented design feature has proven to offer up to 10% more final product in tertiary applications compared to conventional designs, and offers up to 19% less recirculating load. Our A, B and HC mantles can be used with the High Reduction concave.

HIGH REDUCTION

Crushing Chamber Application Guide

17


Manufacturing manganese steel is like baking bread. Even if you have the right ingredients, the bread doesn’t turn out well if you don’t fully understand and control the baking process.

ALLOYS IN-DEPTH PROCESS UNDERSTANDING We offer a range of standard and premium alloys to choose from that meet your specific needs – whether it is increased impact and shock resistance or higher resistance to abrasive rocks. These alloys form the base for our wear liners, and all are made from manganese steel – a mixture of manganese, carbon and chromium. SANDVIK ALLOY MIXES – RANGE OF KEY INGREDIENTS Manganese (Mn)

13 - 18%

Carbon (C)

1.2 – 1.5%

Chromium (Cr)

0.5 – 2%

Each ingredient brings a different characteristic to our wear liners. Manganese, for example, dissolves carbon to prevent carbide formation, while carbon and chromium increase hardness. Chromium has a further benefit of preventing so-called “metal growth”. The ratio of manganese to carbon, as well as the amount of chromium, is directly related to wear resistance during crushing, and the entire casting process needs to be well optimized to produce high-quality liners. We bring our deep manufacturing process knowledge to create the highest quality wear liners. The casting process begins with careful raw material selection for melting in order to reduce impurities. Temperatures are carefully controlled during the melting and pouring phase to get a fine-grain structure for the castings. We then pour the melted metal into carefully designed sand molds for it to solidify and create a solid casting. The castings are then heat treated to dissolve carbides precipitated during solidification and quenched to keep the austenitic microstructure at room temperature, then machined to ensure a perfect fit in your crusher. We use austenitic manganese steel, and the major advantage of this wear material is the work hardening for crushing applications. The high impact in the crushing chamber causes the formation of a surface layer that is two to three times harder than the physical composition of the alloy mix in the wear part. It results in a very tough and durable material that offers superior wear resistance in the surface zone compared to other materials. Through this work-hardening process, the hardness of manganese steel can increase from 210-240 HB to 340-470 HB. 18

Crushing Chamber Application Guide


KEY ASPECTS OF ALLOY MIXES – FROM MANUFACTURING TO WORK HARDENING HIGH Mn/C-ratio

The work-hardening process created by impact offers greater surface hardness and thus increased wear resistance.

Impact resistance

LOW Hardness Casting process – pouring, solidification and heat treatment including quenching

Cr-content %

Crushing Chamber Application Guide

HIGH

19


CRUSHING CHAMBER SOLUTIONS

HIGH

Impact resistance

M1 Alloy

M9 Alloy

M2 Alloy M8 Alloy M7 Alloy

LOW

Wear resistance

HIGH

Standard Alloy Solutions Sandvik offers a range of standard cone crusher liners (mantles and concaves), as well as jaw plates, that are based on our M1, M2, M7 and M8 alloy mixes. The M1 alloy mix has a high resistance to impact and shock, and does not crack easily. Our M2, M7 and M8 alloy mixes offer higher resistance to abrasive rock compared to the M1, but have a lower resistance to shock and impact. Our standard alloys are tough and long lasting, made with Sandvik’s extensive knowledge in the alloy process. You experience all of this in the final quality of our liners. Premium Alloy Solutions We have a newer premium alloy mix - M9 - that offers our highest resistance to abrasive rock, but has a slightly lower resistance to shock and impact compared to the M1. The M9 mix is used for our premium CS and CH crushing chamber solutions. You’ll get up to 20% longer lifetime, resulting in more uptime and lower operating costs with our premium solutions.

20

Crushing Chamber Application Guide


Crushing Chamber Application Guide

21


CUSTOMIZED CRUSHING CHAMBERS Sandvik routinely partners with our customers to find new solutions that will improve your crushing operations. We have combined this knowledge with our application expertise and in-depth knowledge of materials technology to design an optimized crushing chamber. The CX concave for our Sandvik CH660 is a recent customer partnership example. We’ve also developed our EC Top Grip concave, our High Reduction concave, and our S-mantle based on customer collaborations. Within Sandvik’s own foundry, we have full control of the manufacturing process. This ensures consistent quality, predictable service life, a perfect fit and high availability.

22

Crushing Chamber Application Guide


SANDLOCK™ LIFTING TOOLS Sandvik offers a series of safety lifting tools for our CH models of cone crushers. These tools are CE-marked, and specifically designed for Sandvik mantles and concaves. Instead of having to weld on attachment points when replacing parts or undertaking maintenance work, you use these self-locking jaws. They are easy to attach and release, and strong enough to handle the weight of your mantle or concave. The result is faster, safer and easier maintenance. FOUR REASONS WHY 1. Improved on-site and worker safety 2. No welding of attachment points prior to lifting the mantle and/or concave leading to faster turnaround time 3. Designed to fit both new and worn Sandvik mantles and concaves 4. Self-locking clamps are easy to attach/detach from the wear parts CRUSHER MODEL

MANTLE LIFTING TOOL ARTICLE NO.

CONCAVE LIFTING TOOL ARTICLE NO.

CH420

BG00332725

BG00387271

CH430

BG00332725

BG00387271

CH440

BG00227706

BG00387271

CH540

BG00332725

BG00387271

CH550

BG00227706

BG00387271

CH660

BG00328140

BG00387271

CH860i/CH865i

BG00328140

n/a

CH870i

BG00417264

n/a

CH890i/CH895i (CH880)

BG00417260

n/a

Crushing Chamber Application Guide

23


24

Crushing Chamber Application Guide


JAW GUIDE Sandvik’s top-of-the-line CJ-type jaw crushers are specifically built for your primary applications where resizing is the key objective. They allow the material to be processed within your crushing plant. To ensure optimum performance, the jaw crusher needs to have a good feed level and a homogeneous feed.

BASIC CRUSHING PRINCIPLES

26

BASIC PRINCIPLES OF THE SANDVIK CJ JAW CRUSHER

28

SELECTION OF JAW PLATES

30

ONE, TWO, THREE OR SIX-PIECE JAW PLATES

32

WEAR IN PRACTICE

33

CJ211 (J11)

34

CJ409 (JM907)

35

CJ411 (JM1108)

36

CJ412 (JM1208)

37

CJ612 (JM1211)

38

CJ613 (JM1312)

39

CJ615 (JM1511)

40

CJ815 (JM1513)

41

CrushingChamber ChamberApplication ApplicationGuide Guide Crushing

25 25


JAW GUIDE

BASIC CRUSHING PRINCIPLES FEED OPENING The size distribution of the raw material is called the particle size distribution, or PSD for short. It is commonly referred to as the gradation. The PSD of the feed can be expressed as F90 (90% passing square hole size) or F100 (100% passing square hole size), for example. The feed opening determines the maximum feed size for your crushing chamber.

CLOSED SIDE SETTING The closed side setting (CSS) is the last crushing zone and this setting defines your reduction ratio, with a significant effect on the product curve (P80) – your resulting product. The CSS is the minimum discharge opening with moving jaw plates, and the minimum is decided primarily by the power draw (kW), which varies depending on the application.

In a jaw crusher, the feed opening is equal to the feed gap – or the distance from the fixed to the moving jaw plate. The recommended maximum size of the material is approximately 90% of the feed opening and you do not want to bridge the feed opening with slappy or large rocks.

OPEN SIDE SETTING The open side setting (OSS) is the largest distance between the two jaw plates at the bottom of the crusher, and the maximum discharge opening. The space created here allows the product to fall through the crusher to the next crushing stage. The OSS is also the opening of the crusher at rest.

FEED OPENING

CSS 26

Crushing Chamber Application Guide

OSS


Reduction ratio = F80/P80 = 600/200 = 3 PRODUCT

100

FEED

90

Amount passing through (%)

80 70 60 50 40 30 20 10 0 1

10

100

1000

Square hole (%)

REDUCTION RATIO The reduction ratio is the particle size reduction you get from your crusher. It is defined as the ratio between the feed size and the size of the outgoing product, usually measured at the 80% passing point. The feed to the crusher (F80) is divided by product size (P80) giving you the reduction ratio.

NIP ANGLE The nip angle is the angle between the fixed and moving jaw plates. Our Sandvik CJ crushers have an optimum nip angle in the 16-23 degree range. When the OSS is reached, the nip angle is almost at its smallest. The inward motion of the moving jaw plate changes the nip angle, making it larger.

Jaw crushers are normally capable of a reduction ratio of 1:2 or 1:3 in primary applications where resizing is the key objective. This ratio is affected by the feed material’s bulk density, crushability, size distribution and moisture content – among other factors – and will affect the crushing chamber performance.

At small CSS settings, the nip angle increases. A shim plate should be used to improve the crushing chamber’s nip angle, preventing the feed material from moving upward and decreasing your crusher’s performance. The shim plate – which is installed behind the fixed jaw plate – should also be used with slippery rock feeds (a mix of sand and clay, for example). Using a shim plate will decrease the intake opening slightly.

NIP ANGLE

NIP ANGLE

Nip angle is largest when the CSS is reached.

Nip angle is smallest when the OSS is reached. Crushing Chamber Application Guide

27


JAW GUIDE

BASIC WORKING PRINCIPLES OF THE SANDVIK CJ JAW CRUSHER Our Sandvik jaw crushers are of the single-toggle type and feature a deep, symmetrical crushing chamber, a large feed opening for its size, and an ideal nip angle that offers smooth material flow and high reduction efficiency. Jaw crushers are excellent in primary stages where the capacity need is below 800 t/h. The feed material is crushed between two rigid surfaces – one fixed and the other moving. The motion of the moving surface is independent of the load on the jaw crusher, and the crushing action is achieved by the movement of the jaw, which together with the frame and the cheek plates, form the crushing chamber.

The power from the motor is transferred through V-belts to one of the flywheels mounted on the eccentric shaft. The rotation of the eccentric shaft and the movement of the toggle plate cause an elliptical motion of the jaw. When the distance between the jaw and the frame decreases, the incoming process material will be subjected to a compressive stress and thereby be crushed. When the jaw moves away from the frame, the process material can flow down through the chamber.

UPPER CHEEK PLATE

DEFLECTOR PLATE

FIXED PLATE

MOVING PLATE

LOWER CHEEK PLATE

The moving jaw plate is mounted on a “jaw”, which is given a reciprocating motion by an eccentric. The rock is subjected to repeated compressions as it passes downward and and is successively reduced in size until it is small enough to pass out of the crushing chamber.

28

Crushing Chamber Application Guide


Crushing Chamber Application Guide

29


JAW GUIDE

SELECTION OF JAW PLATES There are four desired characteristics to remember when it comes to jaw plate patterns. The “grip effect” means that sharp profiles grip the rocks to improve crushing and reduce wear; the “wear surface” means there is a sharp profile that is worn down quickly; “fines passage” means that there are grooves that help pass fines; and “prevent packing” means that there are grooves and ridges to prevent compaction. Sandvik offers seven teeth patterns and up to three alloy selections (M1, M2, M8) to suit the different types of quarrying and mining applications. Our patterns include Wide Teeth (WT), Wide Wave (WW), Corrugated (C),

Coarse Corrugated (CC), Sharp Teeth (ST), Heavy Duty (HD), Heavy Duty Ultra-Thick (UT). M1 is the standard alloy, offering high resistance to shock and impact. It also work hardens well with hard rock. Our M2 and M8 alloys offer high resistance to abrasive rock, but have lower resistance to shock and impact. The optimal jaw plate selection can be determined based on the rock/ore type characteristics (WI, AI) and the feed characteristics (friction, gradation).

JAW PLATE SELECTION BASED ON ROCK AND FEED CHARACTERISTICS High

ROCK/ORE TYPE CHARACTERISTICS; INTEGRITY AND ABRASIVENESS (WI, AI)

HEAVY DUTY

CORRUGATED

SHARP TEETH

Low Wet, round rock with clay or high fines content

Dry, angular rock, low fines content

FEED CHARACTERISTICS; FRICTION AND GRADATION

The application area determines the most suitable jaw plates - and ultimately the right crushing chamber. We offer seven pattern designs and up to three different alloy selections.

30

Crushing Chamber Application Guide


JAW PLATE PATTERNS - FIXED PLATE WIDE TEETH (WT)

WIDE WAVE (WW)

SHARP TEETH (ST)

Good wear resistance. For feed with a lot of fines. Can be used on both fixed and moving sides.

For slabby and less abrasive feed material. Feed is relatively easy to crush. Good top-size control.

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

CORRUGATED (C)

COARSE CORRUGATED (CC)

HEAVY DUTY (HD)

Suitable for less abrasive material. Good for small CSS settings. Good top-size control.

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

For very abrasive material. Less top-size control. Can be combined with a CC moving plate.

HD ULTRA-THICK (UT)

For very abrasive material. Less top-size control. Fixed plate based on our HD pattern with an extra 30 mm thickness for longer wear life. To be used with the CC moving plate.

Contact your local Sandvik rep to help you select the right plate combination for your application. Crushing Chamber Application Guide

31


JAW GUIDE

ONE, TWO, THREE OR SIX-PIECE JAW PLATES Sandvik offers a range of jaw plate configurations – from one-piece for our smaller models all the way up to six-piece ones for our largest crusher. One-piece jaw plates offer safer, easier and faster exchanges and require the use of a two jaw die-lifting tool due to the component weight. The plates should be rotated more than three times during their life length to maintain the nip angle and to utilize the manganese steel maximally. A delayed flip of the plate often results in a poor nip angle, which often leads to a higher wear rate leading to premature replacement. The end result is a higher cost per ton for the wear liners alone. Our two-piece plate configuration creates one large piece when fastened on the crusher. You can then flip this “one-piece” – as described above – to maintain the nip angle and ensure even wear. Our three-piece jaws are lighter and offer a longer lifetime, lower wear rate, lower cost per ton, and require lower wear part inventory. However, installation of these jaws takes more time and must be done carefully to lock both two-pieces to the middle wear plate fastener (the third piece). Don’t forget to rotate the top and lower plates to maintain the nip angle. Our six-piece jaws are designed for our largest jaw crushers. They are like our three-piece design however each piece is half the size after considering safety, weight and manufacturing aspects. Four single-component wear plates are fastened to two middle wear-plate fasteners, creating one robust jaw plate. You get the same benefits as with our three-piece plate configuration.

1-PIECE PLATE

32

Crushing Chamber Application Guide

2-PIECE PLATE

3-PIECE PLATE

6-PIECE PLATE


WEAR IN PRACTICE JAW PLATES The feed material is crushed between two rigid surfaces – one stationary and the other moving. Moving jaw plates last 50 to 100 percent longer than fixed jaw plates. This is because the crushing movement has a direction that is more favorable for the moving jaw than for the stationary jaw in terms of wear. The rock does not slip against the moving plate, rather there is more sliding on the fixed side where the feeder sits.

This type of sliding increases the wear rate without much crushing effect. In order to increase the lifetime of your liners and make wear more even, you should: 1. Turn jaw plates frequently 2. Choose the right jaw pattern 3. Use the right nip angle, CSS and shim plates 4. Use the right feed arrangement/procedure 5. Choose the right alloy Capacity

• Worn jaw plates reduce capacity • Turn jaw plates to get even wear • Don’t wear down jaw plates until they break Jaw plate change Worn out

Wear

Jaw plates should be changed when one or more of the following happens: • When capacity drops off • When the teeth are gone • When a hole appears on the jaw plate surface • When plates are worn down to 15 mm above the clamping bars CHEEK PLATES Cheek plates do not wear as fast as the jaw plates themselves. The lower cheek plate lasts roughly twice as long compared to the fixed jaw plate. And the upper cheek plate lasts twice as long compared to the lower cheek plate. DEFLECTOR PLATE The feed arrangement has a direct impact on the lifetime of the deflector plates, which are designed to protect the crusher. The life span can be one to two years if the feed material makes regular contact with the deflector plate. If very little contact is made, then it can last the lifetime of the crusher itself.

Crushing Chamber Application Guide

33


JAW GUIDE

CJ211 (J11) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

C

ST

HD/CC

M1

Fixed

400.2207-001

400.0739-001

400.2870-001

Moving

400.1101-001

400.0738-001

400.2869-001

M2

Fixed

400.2207-002

400.0739-002

400.2870-002

Moving

400.1101-002

400.0738-002

400.2869-001

All jaw plates are one piece unless otherwise stated. CHEEK PLATES Upper plate

400.0639-001

DEFLECTOR PLATE

400.3136-001

Lower plate

-

CRUSHING CHAMBERS CORRUGATED (C)

Suitable for less abrasive material. For feed with a lot of fines. Good for small CSS settings. Good top-size control.

34

Crushing Chamber Application Guide

SHARP TEETH (ST)

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

HEAVY DUTY/COARSE CORRUGATED (HD/CC)

For very abrasive material. Used for large CSS settings. Good top-size control


CJ409 (JM907) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

WT

C

M1

Fixed

400.0483-001

400.0418-001

Moving

400.0483-001

400.0417-001

M2

Fixed

400.0483-002

400.0418-002

Moving

400.0483-002

400.0417-002

All jaw plates are one piece unless otherwise stated. CHEEK PLATES Upper plate

10-314-386-000

Lower plate

10-314-404-000

DEFLECTOR PLATE 10-314-479-000

CRUSHING CHAMBERS WIDE TEETH (WT)

CORRUGATED (C)

Good wear resistance. For feed with a lot of fines. Can be used on both fixed and moving sides.

Suitable for less abrasive material. For feed with a lot of fines. Good for small CSS settings. Good top-size control.

Crushing Chamber Application Guide

35


JAW GUIDE

CJ411 (JM1108) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

WT

C

CC

M1

Fixed

400.0436-001

400.0409-001

400.0437-001

Moving

400.0436-001

400.0410-001

400.0433-001

M2

Fixed

400.0436-002

400.0409-002

400.0437-002

Moving

400.0436-002

400.0410-002

400.0433-002

All jaw plates are one piece unless otherwise stated. CHEEK PLATES Upper plate

10-314-262-000

Lower plate

10-314-263-000

DEFLECTOR PLATE 10-214-384-000

CRUSHING CHAMBERS

36

WIDE TEETH (WT)

CORRUGATED (C)

COARSE CORRUGATED (CC)

Good wear resistance. For feed with a lot of fines. Can be used on both fixed and moving sides.

Suitable for less abrasive material. For feed with a lot of fines. Good for small CSS settings. Good top-size control.

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

Crushing Chamber Application Guide


CJ412 (JM1208) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

WT

C

CC

ST

HD

HD/CC

M1

Fixed

400.0411-001

400.0407-001

400.0425-001

402.4744-01

400.0413-001

400.0413-001

Moving

400.0411-001

400.0408-001

400.0420-001

402.4745-01

400.0412-001

400.0420-001

M2

Fixed

400.0411-002

400.0407-002

400.0425-002

402.4744-02

400.0413-002

400.0413-002

Moving

400.0411-002

400.0408-002

400.0420-002

402.4745-02

400.0412-002

400.0420-002

All jaw plates are one piece unless otherwise stated. CHEEK PLATES Upper plate

DEFLECTOR PLATE

10-314-262-000

Lower plate

10-314-263-000

BG00541518

CRUSHING CHAMBERS WIDE TEETH (WT)

CORRUGATED (C)

COARSE CORRUGATED (CC)

Good wear resistance. For feed with a lot of fines. Can be used on both fixed and moving sides.

Suitable for less abrasive material. For feed with a lot of fines. Good for small CSS settings. Good top-size control.

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

SHARP TEETH (ST)

HEAVY DUTY (HD)

HEAVY DUTY/COARSE CORRUGATED (HD/CC)

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

For very abrasive material. Less top-size control. Can be combined with a CC moving plate.

For very abrasive material. Used for large CSS settings. Good top-size control.

Crushing Chamber Application Guide

37


JAW GUIDE

CJ612 (JM1211) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

CC

ST

WW

HD

HD/CC

M1

Fixed

400.2266-001

402.4747-01

400.0440-001*

400.0426-001*

400.0426-001*

-

-

400.0442-001

400.0427-001

400.0427-001

400.0443-001

402.4748-01

400.0438-001*

400.0423-001*

400.0443 -001

Fixed middle Moving Moving middle M2

Fixed

-

-

400.0439-001

400.0424-001

-

400.2266-002

402.4747-02

400.0440-002*

400.0426-002*

400.0426-002*

-

400.0442-002

400.0427-002

400.0427-002

400.0443-002

402.4748-02

400.04383-002*

400.0423-002*

400.0443 -002

-

-

400.0439-002

400.0424-002

-

Fixed middle Moving Moving middle

All jaw plates are one piece unless otherwise stated. *Two pieces CHEEK PLATES Upper plate

402.4239-01

DEFLECTOR PLATE

402.4250-00

Lower plate

402.4635-01

CRUSHING CHAMBERS

38

COARSE CORRUGATED (CC)

SHARP TEETH (ST)

WIDE WAVE (WW)

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

For slabby and less abrasive feed material. Feed is relatively easy to crush. Good top-size control.

HEAVY DUTY (HD)

HEAVY DUTY/COARSE CORRUGATED (HD/CC)

For very abrasive material. Less top-size control. Can be combined with a CC moving plate.

For very abrasive material. Used for large CSS settings. Good top-size control.

Crushing Chamber Application Guide


CJ613 (JM1312) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

C

CC

ST

UT/CC

M1

Fixed

400.0447-001

400.0422-001

400.0963-001

BG00372142-01

Moving

400.0446-001

400.0421-001

400.0964-001

400.0421-001

M2

Fixed

400.0447-002

400.0422-002

-

BG00372142-02

Moving

400.0446-002

400.0421-002

-

400.0421-002

M8

Fixed

-

-

400.0963-004

-

Moving

-

-

400.0964-004

-

All jaw plates are one piece unless otherwise stated. CHEEK PLATES Upper plate

10-214-351-000

Lower plate

10-214-352-000

Upper plate (HX900)

BG00395192

Lower plate (HX900)

BG00395193

DEFLECTOR PLATE

BG00643389

CRUSHING CHAMBERS CORRUGATED (C)

COARSE CORRUGATED (CC)

SHARP TEETH (ST)

Suitable for less abrasive material. For feed with a lot of fines. Good for small CSS settings. Good top-size control.

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

ULTRA THICK/COARSE CORRUGATED (UT/CC)

For very abrasive material. Used for large CSS settings. Less top-size control. UT fixed plate offers longer wear life.

Crushing Chamber Application Guide

39


JAW GUIDE

CJ615 (JM1511) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

CC

ST

HD

HD/CC

M1

Fixed

400.0485-001

400.0490-001

400.0434-001*

400.0434-001*

Fixed middle Moving Moving middle M2

-

400.0435-001

400.0435-001

400.0491-001

400.0434-001*

400.0488-001

-

-

400.0435-001

-

400.0485-002

-

400.0434-002*

-

Fixed middle

-

-

400.0435-002

-

Moving

-

-

400.0434-002*

-

Moving middle

-

-

400.0435-002

-

400.0485-004

400.0490-004

400.0434-004*

400.0434-004*

Fixed

M8

400.0488-001

Fixed Fixed middle Moving Moving middle

-

-

400.0435-004

400.0435-004

400.0488-004

400.0491-004

400.0434-004

400.0488-004

-

-

400.0435-004

-

All jaw plates are one piece unless otherwise stated. *Two pieces CHEEK PLATES Upper plate

402.4521-01

DEFLECTOR PLATE

402.4500-00

Lower plate

402.4522-01

CRUSHING CHAMBERS COARSE CORRUGATED (CC)

SHARP TEETH (ST)

HEAVY DUTY (HD)

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

For very abrasive material. Less top-size control. Can be combined with a CC moving plate.

HEAVY DUTY/COARSE CORRUGATED (HD/CC)

For very abrasive material. Used for large CSS settings. Good top-size control. 40

Crushing Chamber Application Guide


CJ815 (JM1513) JAW CRUSHING SOLUTIONS JAW PLATES ALLOY MIX

PLATE

CC

ST

HD

HD/CC

M1

Fixed

400.0473-001*

400.0780-001

400.0463-001**

400.0463-001**

Fixed middle

-

-

400.0462-001*

400.0462-001*

400.0472-001*

400.0779-001

400.0460-001**

400.0472-001*

Moving middle

-

-

400.0461-001*

-

Fixed

-

-

400.0463-002**

-

Fixed middle

-

-

400.0462-002*

-

Moving

-

-

400.0460-002**

-

Moving middle

-

-

400.0461-002*

-

400.0473-004*

400.0780-004

400.0463-004**

400.0463-004**

Moving M2

M8

Fixed Fixed middle Moving Moving middle

-

-

400.0463-004*

400.0462-004*

400.0472-004*

400.0779-004

400.0460-004**

400.0472-004*

-

-

400.0461-004*

-

All jaw plates are one piece unless otherwise stated. *Two pieces **Four pieces CHEEK PLATES Upper plate

402.4361-01

DEFLECTOR PLATE

402.4337-00

Lower plate

402.4622-01

CRUSHING CHAMBERS COARSE CORRUGATED (CC)

For abrasive material. For feed with a lot of fines. Used for large CSS settings. Good top-size control.

SHARP TEETH (ST)

HEAVY DUTY (HD)

For flaky feed material with a lot of fines. Good gripping ability. Very good top-size control. Highly recommended if the AI is not too high.

For very abrasive material. Less top-size control. Can be combined with a CC moving plate.

HEAVY DUTY/COARSE CORRUGATED (HD/CC)

For very abrasive material. Used for large CSS settings. Good top-size control.

Crushing Chamber Application Guide

41


42

Crushing Chamber Application Guide


CS (S-TYPE) CONE GUIDE Sandvik’s top-of-the-line CS cone crushers are specifically built for your secondary applications where resizing is the key objective. Our high-capacity CS crushers have a large intake opening and a tall crushing chamber, ideal for crushing large feed sizes and processing high tonnage. They allow the material to be processed within your crushing plant and the quality of the product isn’t usually measured in this stage, unless railway ballast is produced. Our CS crushers come equipped with the hydraulic Hydroset system, which provides safety and setting-adjustment functions. And each crusher has a robust design with an adjustable eccentric throw and a constant intake opening.

BASIC CRUSHING PRINCIPLES

44

BASIC PRINCIPLES OF THE SANDVIK CS CONE CRUSHER

45

GETTING THE RIGHT FIT

46

SANDVIK CS CRUSHER DESIGN FEATURES

47

CRUSHING CHAMBER – CS CONE RANGE

48

CS420 (S2800)

51

CS430 (S3800)

52

CS440 (S4800)

54

CS550 56 CS660 (S6800)

57

Crushing Chamber Application Guide

43


CS (S-TYPE) CONE GUIDE

BASIC CRUSHING PRINCIPLES FEED OPENING The size distribution of the raw material is called the particle size distribution, or PSD for short. It is commonly referred to as the gradation. The PSD of the feed can be expressed as F90 (90% passing square hole size) or F100 (100% passing square hole size), for example. The feed opening determines the maximum feed size for your crushing chamber. In a CS cone crusher, the feed opening is equal to the distance from the mantle to the concave at the top of the crusher on its open side. As wear occurs in the crushing chamber, the upward movement of the main shaft (and the mantle) maintains the feed opening and performance during the entire service life of the liners. FEED OPENING

CLOSED SIDE SETTING The closed side setting (CSS) is the smallest distance between the concave and the mantle. It is the last crushing zone and this setting defines your reduction ratio, with a significant effect on the product curve (P80) – your resulting product – crusher capacity, and power draw. OPEN SIDE SETTING The open side setting (OSS) is the largest distance between the concave and the mantle. The space created here allows the product to fall through the crusher to the next processing stage. The OSS is determined by adding the CSS to the eccentric throw. REDUCTION RATIO The reduction ratio is the particle size reduction you get from your crusher. It is defined as the ratio between the feed size and the size of the outgoing product, usually measured at the 80% passing point. The feed to the crusher (F80) is divided by product size (P80) giving you the reduction ratio.

CONCAVE MANTLE CSS

OSS

A typical reduction ratio in a secondary application is in the 1:4 - 1:6 range. This ratio is affected by the feed material’s bulk density, crushability, size distribution and moisture content – among other factors – and will affect the crushing chamber performance.

Reduction ratio = F80/P80 = 200/40 = 5

PRODUCT

FEED

100 90

Amount passing through (%)

80 70 60 50 40 30 20 10 0 0.1 44

Crushing Chamber Application Guide

1

10 Square hole (mm)

100

1000


BASIC PRINCIPLES OF THE SANDVIK CS CONE CRUSHER In our Sandvik CS cone crushers, crushing occurs between a fixed concave and a gyrating mantle that is mounted on the main shaft assembly. The acceleration of the mantle is high as it makes between four and six revolutions per second depending on the size of the crusher. There is also interparticle crushing which happens when the stone grinds against stone inside the crushing chamber. The main shaft is supported at both ends – a so-called “spider design” – allowing the top of the main shaft to rotate and creating a pivot point. This support at both ends generates an extremely powerful crushing force. The crusher’s drive motor rotates the eccentric assembly at a constant speed through a gear transmission. This causes the main shaft to move like a conical pendulum, crushing material by compressing it multiple times against the concave on the sides. The eccentric mechanism that moves the mantle – coupled with the Hydroset pressure that pushes the mantle upwards – is what generates the force with which the material is crushed. This gyration of the main shaft moves the CSS/OSS around the inner circumference of the concave at any given point. When the distance decreases, the material is crushed through multiple compressions. Then when the mantle moves away from the concave, particles move and shift down through the chamber – or crushing zones – before being crushed again. The combination of mantle and concave needs to have the right geometric match in order to reduce unnecessary wear, and result in maximum output. IMPORTANCE OF THE ECCENTRIC ASSEMBLY The eccentric assembly is the part of the crusher that determines the eccentric motion, which in turn creates the conical pendulum movement. The assembly is made up of the eccentric bushing, which allows you to choose the eccentric throw setting, and the eccentric, which secures the bushing in place. To increase capacity in your CS crusher, use the eccentric throw settings, not the concave, to adjust capacity. By turning the “keys” on the bushing, you can easily change the eccentric throw to one that suits your operation better.

With frequent manual or automatic calibrations, the A-dimension gives you an indication of the status of your liners. A large A-dimension indicates that the liners are new and/or the crusher is running with a large CSS. A small A-dimension indicates that the crusher is operating at a small CSS and/or the liners are worn. This means it’s time for a liner change. It also indicates that there is a volume of oil below the piston. This determines how much the main shaft can be lowered to open up the crushing chamber if tramp metal enters. When the minimum A-dimension is reached, it’s time for a liner change. However, the chamber could be worn out before the minimum A-dimension is reached depending on your CSS and eccentric throw settings. A visual inspection of the crushing chamber is the recommended way to decide when the liners need to be changed. You should not exceed the minimum A-dimension even if there appears to be more wear life in your chamber. Raising the main shaft beyond the minimum A-dimension can cause damage to the spider hub and head nut.

A-DIMENSION

IMPORTANCE OF THE A-DIMENSION The A-dimension is the distance between the underside of the spider hub and the top of the head nut. The CSS setting is determined based on the A-dimension value – or the vertical position of the main shaft.

Crushing Chamber Application Guide

45


CS (S-TYPE) CONE GUIDE

GETTING THE RIGHT FIT SELECTING THE RIGHT MANTLE AND CONCAVE When selecting your mantle and concave, you’ll get the most out of your crushing chamber when you can achieve the right fit between three important factors: the feed, the eccentric throw, and the closed side setting (CSS). Balancing these three elements in the right way will give you the output you want, and will maximize the wear life of your crusher. FEED Knowing your feed size and feed-size opening is the most important of the three factors. It will help you select the right mantle and concave combination – and allow you to properly adjust the eccentric throw and CSS settings to ensure the right output. Determining the feed size is done by checking one of several parameters. For instance, the CSS setting of the jaw crusher; the maximum grizzly gap (GG) in the grizzly feeder; or the maximum square hole (SH) size on the screen deck. Note that separations above about 150 mm are too large to be realistic on a normal screen with square holes, but the SH value can still be used for comparison purposes. To best maintain your crusher and get the fit right, do not select a coarser chamber (i.e. concave) then necessary.

CSS Once you know your feed size and eccentric throw, you can determine the right CSS in order to achieve the final product you want. In some cases, the CSS and eccentric throw will have to be balanced with each other simultaneously in order to achieve the right output. IMPACT OF MANTLE SELECTION ON CSS – “UPPER AND LOWER” EFFECTS The CSS setting is determined based on the A-dimension value – or the vertical position of the main shaft. Some mantles (e.g. A-mantle) have the wear zone higher up in the crushing chamber, meaning that the main shaft does not need to be pushed up significantly to reach a small CSS setting. The resulting larger A-dimension allows for more utilization (wear life) of your crushing chamber, as there is more distance to push the main shaft upwards. Some mantles (e.g. B-mantle) have the wear zone lower in the crushing chamber, which allows the crusher to be run with a large CSS setting. With this mantle selection, the Hydroset piston has sufficient oil underneath it to allow the main shaft to drop, protecting the crusher against tramp iron. This is especially important with new liners.

ECCENTRIC THROW The eccentric throw is one of the parameters that gives your crusher its capacity, and the pendulum movement (or eccentric throw) affects the fit between your mantle and concave. The eccentric throw together with the CSS will determine which mantle is best to use for your application. The mantle and concave have the right match when they are perfectly lined up at the bottom. And the right match between the mantle and the eccentric throw ensures optimal output and an even wear pattern. In the closed position (CSS), the bottom of the mantle should be aligned with the bottom of the concave. If, for example, the mantle is hanging below the concave in the closed position, you will get a bulge with uneven liner wear and your crusher won’t perform optimally. OIL UNDER HYDROSET PISTON

46

Crushing Chamber Application Guide


SANDVIK CS CRUSHER DESIGN FEATURES There are several important design features on all Sandvik CS cone crushers that ensure you maximize your productivity and performance – and get the lowest cost per ton. THE HYDROSET SYSTEM The Hydroset System is a safety and setting-adjustment system that allows you to change key settings – like the CSS, power and pressure – in order to give you maximum productivity and to compensate for liner wear. The system consists of a robust hydraulic piston, which supports the main shaft at the bottom and adjusts its position. By moving the Hydroset piston up and down, the CSS and indirectly the OSS – as well as power and pressure settings – can be changed, thereby changing the size of the crushed material. These settings can be adjusted at any time and even when a full load of material is in the crusher.

ASRI (AUTOMATION) COUPLED WITH HYDROSET The ASRi – or Automatic Setting Regulation Intelligent – system optimizes the performance of the crusher without overloading it, allowing you to get the most out of your crusher. The ASRi constantly monitors the Hydroset pressure, motor power draw and the position of the main shaft, and adapts the crusher’s settings in real time to match feed curve variations and variations in the hardness of the process material. The design allows you to adjust the CSS within a wide range to promote capacity, product size – or both. The ASRi system keeps track of the A-dimension, letting you know when the minimum level is approaching and allowing you to plan for a scheduled mantle change. The system also allows for easier manual crushing chamber calibration and CSS setting adjustment to compensate for crushing chamber wear – ensuring consistent product size.

HYDROSET SYSTEM

Crushing Chamber Application Guide

47


CS (S-TYPE) CONE GUIDE

CRUSHING CHAMBER – CS CONE RANGE IMPORTANCE OF CONCAVE SELECTION The crushing chamber is mostly determined by the concave (or outer liner) selection, consisting of a one-piece lower concave and the upper concave – either one piece or made up of individual segments. There are two to three different standard concave choices for each crusher model (see chart), and each has a specific application area. Use the top size of the feed to determine the right concave to use, and do not select a coarser concave than necessary as this will lead to uneven liner wear. Also remember to use the eccentric throw settings, not the concave, to adjust capacity. STANDARD CS CONCAVES EC

C

MC

CRUSHER MODEL CS420

CS430

CS440

CS550

CS660

EC

EC

EC

EC

EC

C

C

C

C

C

-

MC

MC

-

MC

Concaves are specified as extra course (EC), coarse (C) and medium coarse (MC).

48

Crushing Chamber Application Guide


LOWER CONCAVE COMPATIBILITY WITH A WORN UPPER CONCAVE Faster wear in the lower concave section is quite common since the CS crusher is not always choke fed. An upper concave usually lasts as long as two lower concave sets. The lower concave needs to be replaced more frequently to maintain capacity, and maximize upper concave and mantle wear life. Sandvik offers a second lower concave ring designed to match a half-worn upper concave on our CS430, CS440 and CS660 models (left image). The crushing chamber nip angle is maintained because the second lower concave has an adjusted profile (which takes into account the half-worn upper concave) and is cast and therefore does not alter the geometry of the crushing chamber.

If installing a new lower concave against a half-worn upper concave, an unwanted edge is formed between the new lower concave and the used upper concave (right image). This edge affects the geometry of the crushing chamber and if no remedial actions are taken, causes a temporary but significant drop in performance. This capacity drop can be as much 25% for 15% of the lifetime of the crushing chamber. A standard remedial action is a blow-torched chamfer, but this can affect the crushing chamber’s nip angle, impacting the performance and creating worker safety issues. IMPORTANCE OF MANTLE SELECTION We offer three different standard mantles: A, S and B – and the key differences are the positions of the crushing surface in relation to the contact surface of the head center. Each mantle has a specific application area, so not all mantles are available for all crusher models. You can determine which mantle to use by looking at the combination of eccentric throw, CSS and top feed size. Sandvik’s PlantDesigner software or our Rock Processing Guide can help you select the right mantle profile for your application. Contact your local Sandvik rep for more information. IMPACT OF MANTLE SELECTION ON THE HYDROSET SYSTEM Regardless of the mantle selected, there will be oil underneath the Hydroset piston to allow the main shaft to drop, protecting the crusher against tramp iron. However, with the correct mantle selected based the CSS setting, there will more oil underneath the Hydroset piston thereby allowing the main shaft to be lowered even more. This is especially important with new liners.

Crushing Chamber Application Guide

49


CS (S-TYPE) CONE GUIDE

A-, B- AND S-MANTLES Both the A- and B-mantles have the same profile, so there is no difference in the crushing chamber. The position of the crushing surface in relation to the contact surface of the head center is where they differ. On A-mantles, the wear zone is higher up in the crushing chamber, meaning that the main shaft does not need to be pushed up significantly to reach a small CSS setting. The resulting larger A-dimension allows for more utilization (wear life) of your crushing chamber as there is more distance to push the main shaft upwards. An A-mantle should be used to optimize wear characteristics when using a small CSS and eccentric throw. If an A-mantle is used with large CSS settings, the main shaft needs to be lowered, possibly to the point where the crusher operates with little or no oil below the Hydroset piston. This can lead to mechanical failure if metal objects enter. On B-mantles, the wear zone is lower in the crushing chamber, which allows you to run the crusher with large CSS and/or large eccentric throw settings. With this mantle selection, the Hydroset piston has sufficient oil underneath it to allow the main shaft to drop, protecting the crusher against tramp iron. This is especially important with new liners. On the S-mantle, the position of the crushing surface in relation to the contact surface of the head center is in between the A- and B-mantles. Sandvik’s PlantDesigner software or our Rock Processing Guide can help you select the right mantle profile for your application. Contact your local Sandvik rep for more information.

The position of the crushing surface in relation to the contact surface of the head center is where the A- and B-mantles differ. With an A-mantle (orange), the wear zone is higher up, and with a B-mantle (blue) the wear zone is lower down.

WANT AN EVEN BIGGER CSS? Select our customized liner sets EC/BC, ECC/B and ECC/BC The maximum eccentric throw setting is the limiting factor if your desired end product is large-size material, such as ballast. In order to increase the CSS opening right from the start, we offer the EC/BC, ECC/B and ECC/BC crushing chamber solutions, which increase the CSS range by 18 mm, 21 mm and 41 mm respectively (compared to our standard EC/B chamber). These specialized liner sets allow you to start producing your end product right from the beginning with your CH440, making your operations more profitable. The increased CSS does come at a cost of lower crushing chamber lifetime.

50

Crushing Chamber Application Guide


CS420 (S2800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

57

60

64

16 177

267

20 25

CONCAVE

ALLOY MIX M1

M2

EC upper

442.8550-00

442.8550-90

-

EC lower

442.8464-00

442.8464-90

-

CONCAVE C

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

M7

MANTLE C.S.S. (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

54

16 148

223

20 25

CONCAVE

ALLOY MIX M1

M2

EC upper

442.7379-00

442.7379-90

M7 -

EC lower

442.8522-00

442.8522-90

442.8522-91

ALLOY MIX

MANTLE M1

M2

A

442.9288-01

442.9288-02

M7 -

B

442.6789-01

442.6789-02

442.6789-03

MANTLE TYPE =A

=B

Crushing Chamber Application Guide

51


CS (S-TYPE) CONE GUIDE

CS430 (S3800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

16 266

400

20 25 30

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS430:04)

M1

M2

M7

EC upper

442.8484-00

442.8484-90

442.8484-91

EC lower

452.7001-901

452.7001-902

452.7001-903

EC2 second lower

BG00174250

BG00174251

BG00174252

NON-METALLIC BACKING (CS430:01, S3800) EC upper

442.8484-00

442.8484-90

442.8484-91

EC lower

442.8477-00

442.8477-90

442.8477-91

EC2 second lower

452.1952-901

452.1952-902

452.1952-903

CONCAVE C

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

54

57

60

16 222

334

20 25 30

CONCAVE SEMI-METALLIC BACKING (CS430:04)

M1

M2

M7

C upper

442.8485-00

442.8485-90

442.8485-91

C lower

452.7002-901

452.7002-902

452.7002-903

C2 second lower

BG00174521

BG00174693

BG00174694

NON-METALLIC BACKING (CS430:01, S3800) C upper

52

ALLOY MIX

M1

M2

M7

442.8485-00

442.8485-90

442.8485-91

C lower

442.8478-00

442.8478-90

442.8478-91

C2 second lower

452.1954-901

452.1954-902

452.1954-903

Crushing Chamber Application Guide

64


CONCAVE MC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

16 174

263

20 25 30

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS430:04)

M1

M2

M7

MC upper

452.1465-901

452.1465-902

452.1465-903

MC lower

452.7003-901

452.7003-902

452.7003-903

MC2 second lower

BG00174595

BG00174596

BG00174597

M1

M2

M7

NON-METALLIC BACKING (CS430:01, S3800) MC upper

452.1465-901

452.1465-902

452.1465-903

MC lower

452.1464-901

452.1464-902

452.1464-903

MC2 second lower

452.1973-901

452.1973-902

452.1793-903

MANTLE

ALLOYS M1

M2

M7

A

442.8470-01

442.8470-02

442.8470-03

B

442.8471-01

442.8471-02

442.8471-03

MANTLE TYPE =A

=B

Crushing Chamber Application Guide

53


CS (S-TYPE) CONE GUIDE

CS440 (S4800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

83

20 332

500

25 30 36

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS440:04)

M1

M2

M7

EC upper

442.8115-00

442.8115-90

442.8115-91

EC lower

452.6264-901

452.6264-902

452.6264-903

NON-METALLIC BACKING (CS440:01, S4800) EC upper

M1

M2

M7

442.8115-00

442.8115-90

442.8115-91

EC lower

442.8114-00

442.8114-90

442.8114-91

EC2 second lower

452.1955-901

452.1955-902

452.1955-903

CONCAVE C

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE C.S.S. (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

20 295

445

25 30 36

CONCAVE SEMI-METALLIC BACKING (CS440:04)

M1

M2

M7

C upper

442.8099-00

442.8099-90

442.8099-91

C lower

452.3821-901

452.3821-902

452.3821-903

NON-METALLIC BACKING (CS440:01, S4800) C upper

54

ALLOY MIX

M1

M2

M7

442.8099-00

442.8099-90

442.8099-91

C lower

442.8098-00

442.8098-90

442.8098-91

C2 second lower

452.0945-901

452.0945-902

452.0945-903

Crushing Chamber Application Guide

83


CONCAVE MC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

83

20 222

335

25 30 36

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS440:04)

M1

M2

M7

MC upper

452.0474-901

452.0474-902

452.0474-903

MC lower

452.6265-901

452.6265-902

452.6265-903

NON-METALLIC BACKING (CS440:01, S4800) MC upper

M1

M2

M7

452.0474-901

452.0474-902

452.0474-903

MC lower ring

452.0273-901

452.0273-902

452.0273-903

MC2 second lower

452.1972-901

452.1972-902

452.1972-903

MANTLE

ALLOY MIX M1

M2

M7

A

442.8089-01

442.8089-02

442.8089-03

S

452.0943-001

452.0943-002

452.0943-003

B

442.8070-01

442.8070-02

442.8070-03

MANTLE TYPE =A

=S

=B

CUSTOMIZED LINERS CONCAVE NON-METALLIC BACKING (CS440:01, S4800)

ALLOY MIX M1

M2

M7

EC/ECC upper

442.8115-00

442.8115-90

442.8115-91

EC lower

442.8114-00

442.8114-90

442.8114-91

ECC lower

452.1544-001

452.1544-002

452.1544-003

MANTLE

ALLOY MIX M1

M2

M7

B

442.8070-01

442.8070-02

442.8070-03

BC

452.1545-001

452.1545-002

452.1545-003

Our customized liner sets - EC/BC, ECC/B and ECC/BC – have been designed to directly produce large-size product, such as ballast, when newly installed.

Crushing Chamber Application Guide

55


CS (S-TYPE) CONE GUIDE

CS550 STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

83

24 28 32 286

431

36 40 44 48

CONCAVE

ALLOY MIX M1

M2

M7

M9*

EC upper

670.4004-001

670.4004-002

670.4004-003

670.4004-005

EC lower

670.4003-001

670.4003-002

670.4003-003

670.4003-005

CONCAVE C

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

83

24 28 32 229

345

36 40 44 48

CONCAVE

ALLOY MIX M1

M2

M7

M9*

C upper

670.4007-001

670.4007-002

670.4007-003

670.4007-005

C lower

670.4006-001

670.4006-002

670.4006-003

670.4006-005

M1

M2

M7

M9*

A

452.9000-001

452.9000-002

452.9000-003

452.9000-005

S

452.9002-001

452.9002-002

452.9002-003

452.9002-005

B

452.9001-001

452.9001-002

452.9001-003

452.9001-005

MANTLES

ALLOY MIX

MANTLE TYPE =A

56

* M9 is a premium product.

=S

Crushing Chamber Application Guide

=B


CS660 (S6800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

83

76

83

20 25 413

622

30 35 40

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CSCS660:03)

M1

M2

M7

EC upper

442.8981-00

442.8981-90

442.8981-91

EC lower

452.5920-901

452.5920-902

452.5920-903

NON-METALLIC BACKING (CS430:01, S3800) EC upper

442.8981-00

442.8981-90

EC lower

442.8979-00

442.8979-90

CONCAVE C

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

20 25 369

556

30 35 40

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS660:03)

M1

M2

C upper

442.9072-00

442.9072-00

C lower

452.3822-901

452.3822-902

NON-METALLIC BACKING (CS660:01, S6800) C upper C lower C2 second lower

M1

M2

442.9072-00

442.9072-90

442.9071-00

442.9071-90

BG01221422-01

BG01221422-02

MANTLES

ALLOY MIX M1

M2

A

442.8982-01

442.8982-02

B

442.8983-01

442.8983-02

MANTLE TYPE =A

=B

Crushing Chamber Application Guide

57


CONCAVE MC

MAX. FEED SIZE ECC. THROW (mm) (mm) F90

F100

MANTLE CSS (mm) 19

22

25

29

32

35

38

41

44

48

51

54

57

60

64

70

76

20 25 310

468

30 35 40

CONCAVE

ALLOY MIX

SEMI-METALLIC BACKING (CS660:03)

M1

M2

MC upper

452.9040-901

452.9040-902

MC lower

452.9041-901

452.9041-902

MANTLES

ALLOY MIX M1

M2

A

442.8982-01

442.8982-02

B

442.8983-01

442.8983-02

MANTLE TYPE =A

=B

CUSTOMIZED LINERS CUSTOMIZED A-MANTLE (BG01238109) This mantle has a specific application area as the wear zone is in between that of an A- and B-mantle. Available as BG01238109-01 (M1), BG01238109-02 (M2) and BG01238109-03 (M7).

58

Crushing Chamber Application Guide

83


Crushing Chamber Application Guide

59


60

Crushing Chamber Application Guide


CH (H-TYPE) CONE GUIDE Sandvik’s top-of-the-line CH cone crushers are specifically built for your high-capacity secondary applications, high-reduction tertiary and quaternary applications, and pebble-crushing applications. They come equipped with the hydraulic Hydroset System, which provides safety and setting-adjustment functions. And each crusher has a robust design with an adjustable eccentric throw and a constant intake opening. Choose from extra-coarse crushing chambers with the largest intake to extremely fine crushing chambers – all engineered to be the perfect fit for your application.

BASIC CRUSHING PRINCIPLES

62

BASIC PRINCIPLES OF THE SANDVIK CH CONE CRUSHER

63

GETTING THE RIGHT FIT

65

SANDVIK CH CRUSHER DESIGN FEATURES

66

CRUSHING CHAMBER – CH CONE RANGE

68

PREMIUM CRUSHING CHAMBER SOLUTIONS

74

CH420 (H2000)

76

CH430 (H3800)

80

CH440 (H4800, H4000)

86

CH540 92 CH550 96 CH660 (H6800)

100

CH860i (CH860)

108

CH865i (CH865)

112

CH870i (CH870, H7800)

116

CH890i (CH890, CH880, H8800)

124

CH895i (CH895, CH880, H8800)

130

Crushing CrushingChamber ChamberApplication ApplicationGuide Guide

61 61


CH (H-TYPE) CONE GUIDE

BASIC CRUSHING PRINCIPLES FEED OPENING The size distribution of the raw material is called the particle size distribution, or PSD for short. It is commonly referred to as the gradation. The PSD of the feed can be expressed as F90 (90% passing square hole size) or F100 (100% passing square hole size), for example. The feed opening determines the maximum feed size for your crushing chamber. In a CH cone crusher, the feed opening is equal to the distance from the mantle to the concave at the top of the crusher on its open side. As wear occurs in the crushing chamber, the upward movement of the main shaft (and the mantle) maintains the feed opening and performance during the entire service life of the liners. FEED OPENING

CONCAVE

CLOSED SIDE SETTING The closed side setting (CSS) is the smallest distance between the concave and the mantle. It is the last crushing zone and this setting defines your reduction ratio, with a significant effect on the product curve (P80) – your resulting product – crusher capacity, and power draw. OPEN SIDE SETTING The open-side setting (OSS) is the largest distance between the concave and the mantle. The space created here allows the product to fall through the crusher to the next processing stage. The OSS is determined by adding the CSS to the eccentric throw. REDUCTION RATIO The reduction ratio is the particle size reduction you get from your crusher. It is defined as the ratio between the feed size and the size of the outgoing product, usually measured at the 80% passing point. The feed to the crusher (F80) is divided by product size (P80) giving you the reduction ratio.

MANTLE OSS

CSS

A typical reduction ratio in a secondary application is in the 1:4 - 1:6 range, while in a tertiary/finer application it’s in the 1:2 - 1:4 range. This ratio is affected by the feed material’s bulk density, crushability, size distribution and moisture content – among other factors – and will affect the crushing chamber performance.

Reduction ratio = F80/P80 = 32/8 = 4 PRODUCT

FEED

100 90

Amount passing through (%)

80 70 60 50 40 30 20 10 0 0.01 62

Crushing Chamber Application Guide

0.1

1 Square hole (mm)

10

100


BASIC PRINCIPLES OF THE SANDVIK CH CONE CRUSHER In our Sandvik CH cone crushers, crushing occurs between a fixed concave ring and a gyrating mantle that is mounted on the main shaft assembly. The acceleration of the mantle is high as it makes between four and seven revolutions per second depending on the size of the crusher. Between each compression, the particles change position before getting crushed again. And in fine crushing applications, much of the crushing is done as stone grinds against stone – also known as interparticle crushing.

PIVOT POINT

CONCAVE MANTLE

The main shaft is supported at both ends – a so-called “spider design” – allowing the top of the main shaft to rotate and creating a pivot point. This support at both ends generates an extremely powerful crushing force. The crusher’s drive motor rotates the eccentric assembly at a constant speed through a gear transmission. This causes the main shaft to move like a conical pendulum, crushing material by compressing it multiple times against the concave on the sides. The eccentric mechanism that moves the mantle – coupled with the Hydroset pressure that pushes the mantle upwards – is what generates the force with which the material is crushed. This gyration of the main shaft moves the CSS/OSS around the inner circumference of the concave at any given point. When the distance decreases, the material is crushed through multiple compressions. Then when the mantle moves away from the concave, particles move and shift down through the chamber – or crushing zones – before being crushed again. The combination of mantle and concave needs to have the right geometric match in order to reduce unnecessary wear, and result in maximum output. CRUSHING FORCE The crushing force is the result when power and pressure are applied in the chamber. Power is the force created by the conical movement of the main shaft, while pressure is how much force is pushing upward – or the Hydroset pressure. This Hydrocone® design allows for continuous monitoring of the pressure – and the known crushing force inside the chamber.

ECCENTRIC ASSEMBLY

HYDROSET SYSTEM α The concave, mantle, eccentric assembly and the location of the pivot point determine the chamber geometry of the Sandvik cone crusher.

CRUSHING FORCE, F

REACTION FORCE, F1

F1 + F2

α

F3

REACTION FORCE, F2

REACTION FORCE, F3 The Hydroset pressure is proportional to the crushing force (F).

Crushing Chamber Application Guide

63


CH (H-TYPE) CONE GUIDE RELATION BETWEEN POWER AND PRESSURE The power and pressure variables together exert the crushing force – and they have to be balanced. Power is important during coarse crushing, while pressure is the important factor in fine crushing. For example, too much power in fine crushing applications can result in damage to the crusher. But in Sandvik CH crushers, the Automatic Setting Regulation Intelligent system (ASRi) balances the two factors based on your feed characteristics. The crushing force is maximized under controlled conditions to protect the crusher and achieve the right balance for your operation. During continuous and stable crushing operations with a constant feed, the power draw is linear to the crushing force (and the Hydroset pressure). With coarse crushing, the pressure is lower compared to fine crushing but the power consumption is higher. It is usually the crushing force (or hydraulic pressure) that limits the maximum crusher load during fine crushing, while the power limits it in coarse crushing.

Hydraulic pressure

Maximum permitted

Packing

IMPORTANCE OF THE A-DIMENSION The A-dimension is the distance between the underside of the spider hub and the top of the head nut. The CSS setting is determined based on the A-dimension value – or the vertical position of the main shaft. With frequent manual or automatic calibrations, the A-dimension gives you an indication of the status of your liners. A large A-dimension indicates that the liners are new and/or the crusher is running with a large CSS.

Fine crushing

Coarse crushing

Power draw

IMPORTANCE OF THE ECCENTRIC ASSEMBLY The eccentric assembly is the part of the crusher that determines the eccentric motion, which in turn creates the conical pendulum movement. The assembly is made up of the eccentric bushing, which allows you to choose the eccentric throw setting, and the eccentric, which secures the bushing in place. By turning the “keys” on the bushing, you can easily change the eccentric throw to one that suits your operation better.

Maximum permitted

CRUSHING ZONES IN A CHAMBER As particles move through the crushing chamber, they pass through different crushing zones. The zones change size because of the geometry of the crushing chamber. The zones become narrower as particles move down the chamber, increasing the degree of particle reduction in steps as it moves down. The height of each zone is the distance a particle travels during one eccentric revolution. In mining, the aim is to obtain the highest possible degree of reduction, and the smallest gap between crushing surfaces in the last crushing zone. In aggregate production, however, it’s about getting the proper product shape and a product curve with the target fractions.

A small A-dimension indicates that the crusher is operating at a small CSS and/or the liners are worn. This means it’s time for a liner change. It also indicates that there is a volume of oil below the piston. This determines how much the main shaft can be lowered to open up the crushing chamber if tramp metal enters. When the minimum A-dimension is reached, it’s time for a liner change. However, the chamber could be worn out before the minimum A-dimension is reached depending on your CSS and eccentric throw settings. A visual inspection of the crushing chamber is the recommended way to decide when the liners need to be changed. You should not exceed the minimum A-dimension even if there appears to be more wear life in your crushing chamber. Raising the main shaft beyond the minimum A-dimension can cause damage to the spider hub and head nut.

A-DIMENSION

64

Crushing Chamber Application Guide


GETTING THE RIGHT FIT SELECTING THE RIGHT MANTLE AND CONCAVE When selecting your mantle and concave, you’ll get the most out of your crushing chamber when you can achieve the right fit between three important factors: the feed, the eccentric throw, and the closed side setting (CSS). Balancing these three elements in the right way will give you the output you want, and will maximize the wear life of your crushing chamber.

As an example, an eccentric throw of 18 mm will give you 28 crushing zones, while an eccentric throw of 32 mm will give you 20 crushing zones. The fewer zones you have, the more tonnage you’ll get because the rock will go through the crusher much faster. However, a higher throw always gives a coarser product. It is about achieving a balance between desired product size (whether it is a P80 or a target fraction) and tonnage.

FEED Knowing your feed size and feed-size opening is the most important of the three factors. It will help you select the right mantle and concave combination – and allow you to properly adjust the eccentric throw and CSS settings to ensure the right output.

ECC 18 mm 28 zones

ECCENTRIC THROW The eccentric throw is one of the parameters that gives your crusher its capacity, and the pendulum movement (or eccentric throw) affects the fit between your mantle and concave. The eccentric throw together with the CSS will determine which mantle is best to use for your application. The mantle and concave have the right match when they are perfectly lined up at the bottom. And the right match between the mantle and the eccentric throw ensures optimal output and an even wear pattern. In the closed position (CSS), the bottom of the mantle should be aligned with the bottom of the concave. If, for example, the mantle is hanging below the concave in the closed position, you will get a bulge with uneven liner wear and your crusher won’t perform optimally. CSS Once you know your feed size and eccentric throw, you can determine the right CSS in order to achieve the final product you want. In some cases, the CSS and eccentric throw will have to be balanced with each other simultaneously in order to achieve the right output. IMPACT OF ECCENTRIC THROW ON CRUSHING ZONES The height of each crushing zone is the distance a particle travels during one eccentric revolution. With larger throws, the particles have more room to drop, offering fewer crushing zones compared to a smaller throw.

189 mtph

ECC 32 mm 20 zones

328 mtph

IMPACT OF MANTLE SELECTION ON CSS – HYDROSET EFFECTS The CSS setting is determined based on the A-dimension value – or the vertical position of the main shaft. Mantles (e.g. A-mantle) have the wear zone higher up in the crushing chamber, meaning that the main shaft does not need to be pushed up significantly to reach a small CSS setting. The resulting larger A-dimension allows for more utilization (wear life) of your crushing chamber, as there is more distance to push the main shaft upwards. Some mantles (e.g. B-mantle) have the wear zone lower in the crushing chamber, which allows the crusher to be run with a large CSS setting. With this mantle selection, the Hydroset piston has sufficient oil underneath it to allow the main shaft to drop, protecting the crusher against tramp iron. This is especially important with new liners.

OIL UNDER HYDROSET PISTON

Crushing Chamber Application Guide

65


CH (H-TYPE) CONE GUIDE

SANDVIK CH CRUSHER DESIGN FEATURES There are several important design features on all Sandvik CH cone crushers that ensure you maximize your productivity and performance – and get the lowest cost per ton. THE HYDROSET SYSTEM The Hydroset System is a safety and setting-adjustment system that allows you to change key settings – like the CSS, power and pressure – in order to give you maximum productivity and to compensate for liner wear. The system consists of a robust hydraulic piston, which supports the main shaft at the bottom and adjusts its position. By moving the Hydroset piston up and down, the CSS and indirectly OSS – as well as power and pressure settings – can be changed, thereby changing the size of the crushed material. These settings can be adjusted at any time and even when a full load of material is in the chamber.

ASRI (AUTOMATION) COUPLED WITH HYDROSET The ASRi – or Automatic Setting Regulation Intelligent – system optimizes the performance of the crusher without overloading it, allowing you to get the most out of your crusher. The ASRi constantly monitors the Hydroset pressure, motor power draw and the position of the main shaft, and adapts the crusher’s settings in real time to match feed curve variations and variations in the hardness of the process material. The design allows you to adjust the CSS within a wide range to promote capacity, product size – or both. The ASRi system also offers a simple push-button, metal-to-metal calibration, which can be done within seconds, even from the control room. Instead of having to do it manually, the system will automatically adjust your crusher settings to compensate for crushing chamber wear – ensuring consistent product size. Frequent calibration is required for the system to keep good track of the A-dimension. This is particularly important when you are operating the crusher in an auto-CSS mode.

HYDROSET SYSTEM

66

Crushing Chamber Application Guide


CONSTANT LINER PROFILE Sandvik crushing chambers are designed to maintain an even shape of the liners to extend your operational life and increase your output. As wear occurs, the upward movement of the mantle maintains both the shape and volume of the chamber, and the size of the feed opening during the entire service life of the liners. This means that wear is evenly distributed over the surface of each liner, so the production rate of the crusher is never reduced as the liners wear.

A-DIMENSION

A-DIMENSION

Constant Liner Profile - As wear occurs, the upward movement of the mantle maintains the shape and volume of the chamber and the size of the feed opening during the entire service life of the liners.

WIDE RANGE OF CRUSHING CHAMBER SOLUTIONS To get the most out of your crusher, choosing the right chamber based on its application is vital. Our offering covers extra-coarse crushing chambers with the largest intake for high-capacity crushing all the way to extremely fine crushing chambers for high reduction or extremely tough pebble crushing. All chambers are engineered to be the perfect fit for your application.

Crushing Chamber Application Guide

67


CH (H-TYPE) CONE GUIDE

STANDARD CRUSHING CHAMBERS – CH CONE RANGE IMPORTANCE OF CONCAVE SELECTION The crushing chamber is mostly determined by the concave (or outer liner) selection. We offer between four and seven different standard concaves per crusher model, each of which has a specific application area. They range from extra course all the way to fine. Your top feed size will dictate the correct concave to use, and you can determine this feed size by matching it up with the square hole size or the CSS of the crusher beforehand. With the right concave, material starts to be crushed at the very top of the chamber, rather than material dropping to the middle or bottom – which can result in uneven wear. Concaves are specified as extra course (EC), course extra (CX), coarse (C), medium coarse (MC), medium (M), medium fine (MF), fine (F), extra-fine extra (EFX), extra fine (EF) and extra-extra fine (EEF).

STANDARD CONCAVES – SEVEN SOLUTIONS EC

CX

MF

F

C

MC

M

EF

EEF

FOR FINER APPLICATIONS – FIVE “SHORT” CHAMBER SOLUTIONS MF

68

Crushing Chamber Application Guide

F

EFX


We have developed a range of standard “short” chambers to increase the crushing forces within the chamber. To achieve a higher size reduction with smaller feed sizes, our standard EF mantle (see page 73) is used. We offer one to three different concaves per model.

CRUSHER MODEL CH420

CH430

CH440

CH540

CH550

CH660

CH860i/865i* CH870i

CH890i/895i*

EC

EC

EC Top Grip

EC Top Grip

EC Top Grip

EC

EC Top Grip

EC

EC Top Grip

-

-

-

-

-

CX

-

-

-

C

C

C

C

C

C

C

C

C

-

MC

MC

-

MC

MC

MC

MC

MC

M

M

M

M

M

M

M

M

M

MF

MF

MF

-

MF

MF

-

MF

MF

F

F

F

F

F

F

F*

F

F

-

-

-

-

-

-

-

-

EFX*

EF

EF

EF

EF

-

EF

EF*

EF

EF*

-

-

-

-

-

-

-

-

EEF*

“Short” chambers in blue.

Crushing Chamber Application Guide

69


CH (H-TYPE) CONE GUIDE

SELECTING THE WRONG CONCAVE If you use a crushing chamber that’s too big (the feed material is too small), the material is crushed in the lower part of the chamber. This leads to a limited amount of wear at the top of the chamber, and accelerated wear at the bottom. This uneven wear profile shortens the lifespan of your crushing chamber.

LIMITED AMOUNT OF WEAR

ACCELERATED WEAR

CHANGING YOUR CONCAVE When changing your crushing chamber (or concave), you will often move toward a finer chamber – meaning lower capacity at the same throw and CSS. However, you should avoid selecting a coarser chamber to increase capacity. Sandvik’s PlantDesigner software or our Rock Processing Guide can help you estimate new operating conditions and select the right crushing chamber profile. Contact your local Sandvik rep for more information. IMPORTANCE OF MANTLE SELECTION There are five different standard Sandvik mantles – A, S/D, B, HC and EF. Each mantle has a specific application area, so not all mantles are available for all crusher models. You can determine the mantle to use by looking at the combination of eccentric throw, CSS and top feed size. Sandvik’s PlantDesigner software or our Rock Processing Guide can help you select the right mantle profile for your application. Contact your local Sandvik rep for more information.

70

Crushing Chamber Application Guide


STANDARD CH MANTLES

A

B

EF

HC

IMPACT OF MANTLE SELECTION ON THE HYDROSET SYSTEM Regardless of the mantle selected, there will be oil underneath the Hydroset piston to allow the main shaft to drop, protecting the crusher against tramp iron. However, when the correct mantle is selected based on the CSS setting there will be more oil underneath the Hydroset piston, thereby allowing the main shaft to be lowered even more. This is especially important with new liners.

Crushing Chamber Application Guide

71


CH (H-TYPE) CONE GUIDE

A-, B- AND S-MANTLES Both the A- and B-mantles have the same profile, so there is no difference in the crushing chamber. The position of the crushing surface in relation to the contact surface of the head center is where they differ. On A-mantles, the wear zone is higher up in the crushing chamber, meaning that the main shaft does not need to be pushed up significantly to reach a small CSS setting. The resulting larger A-dimension allows for more utilization (wear life) of your crushing chamber as there is more distance to push the main shaft upward. An A-mantle should be used to optimize wear characteristics when using a small CSS and eccentric throw. On B-mantles, the wear zone is lower in the crushing chamber, which allows you to run the crusher with a large CSS and/or large eccentric throw settings. With this mantle selection, the Hydroset piston has sufficient oil underneath it to allow the main shaft to drop, protecting the crusher against tramp iron. This is especially important with new liners. On the S-mantle, the position of the crushing surface in relation to the contact surface of the head center is in between the A- and B-mantles. Sandvik’s PlantDesigner software or our Rock Processing Guide can help you select the right mantle profile for your application. Contact your local Sandvik rep for more information.

The position of the crushing surface in relation to the contact surface of the head center is where the A- and B-mantles differ. With an A-mantle (orange), the wear zone is higher up, and with a B-mantle (blue) the wear zone is lower down.

SELECTING AN A- OR B-MANTLE The A-mantle should be used with small eccentric throws and small CSS settings. As the throw and CSS get bigger, you’ll need a mantle where the wear zone is lower in the crushing chamber (a B-mantle), thus keeping the oil volume under the Hydroset piston at a secure level. If you have a lot of tramp events, then the B-mantle may also be preferable since it allows for a bigger CSS opening that can let tramp material out of the crushing chamber when the dump valve system is triggered. This is when the main shaft is lowered, opening up the chamber.

72

Crushing Chamber Application Guide


USING THE WRONG MANTLE: AN A-MANTLE IN A B-MANTLE APPLICATION If an A-mantle is used with large CSS settings, the main shaft needs to be lowered, possibly to the point where the crusher operates with little or no oil below the Hydroset piston. This can lead to mechanical failure if metal objects enter the crushing chamber. It also leads to nose formation of the mantle (see chapter 9), which restricts the outflow of material and provides the wrong readings for the ASRi metal-to-metal calibration. HC TO B-MANTLE COMPARISON The HC or heavy-choke mantle is designed to improve your reduction ratio. It has a strangulated intake that reduces material volume in the chamber, and permits crushing at smaller settings. This means you get larger reduction, less recirculating load and better shape in fine fractions (5-8 mm). While it provides a larger feed opening, it also reduces capacity – particularly with new liners.

EF MANTLE In order to increase the crushing forces within the chamber, the EF mantle has a step design creating a “short” crushing chamber after the final step. Used in finer applications, combining our EF mantle with a suitable concave (MF, F, EFX, EF, EEF) will give you higher reduction and less circulating load (whether it is a P80 or a target fraction) compared to an F concave with a suitable mantle.

Crushing Chamber Application Guide

73


CH (H-TYPE) CONE GUIDE

PREMIUM CRUSHING CHAMBER SOLUTIONS Sandvik offers an innovative range of premium chamber solutions that are created based on your needs, and deliver consistently high availability and reliability. These patented solutions offer significant productivity gains and safety improvements in your crushing operations, and improve your bottom line. FLEXIFEED MANTLE Our Flexifeed (FF) mantle – or moving liner – is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

Product name

FLEXIFEED mantle

Application

Secondary crushing applications. It has a varying feed opening, ideal if the crusher feed is not calibrated.

Crusher compatibility

SANDVIK CH420, CH430, CH440, CH540, CH550, CH660, CH860i, CH870i, CH890i.

Concave match

EC, CX (CH660), C, MC

OVERSIZE BREAKER MANTLE Our Oversize Breaker (OB) mantle is part of our “short” chamber solutions for tertiary or final crushing applications. It is based on our EF-mantle profile design and it has a varying feed opening that is ideal if the crusher feed has a larger proportion of oversized process material than anticipated.

Product name

Oversize Breaker (OB) mantle

Application

Finer applications: tertiary or final crushing stages. It has a varying feed opening, ideal if the crusher feed is not calibrated. It increases the allowable top size in short crushing chambers and helps to prevent bridging from oversized rock/ore.

Crusher compatibility and concave match

74

Crushing Chamber Application Guide

CH865i: F, EF CH870i: MF, F, EF CH890i (CH880): F CH895i (CH880): EF, EFX, EEF


OPTIAGG MANTLE – PART OF OUR OPTIAGG SOLUTION* Our innovative Optiagg solution, designed for the tertiary or final crushing stages, is our latest premium offering which offers up to 30% more desired product (whether it is a P80 or a target fraction). Three to six wedges have been specially designed on the high-efficiency mantle to alter the crushing chamber geometry, reduce interparticle breakage and change how crushing forces are generated within the crushing chamber. The real difference is the applied computer modeling and analysis, which is necessary to find the optimal premium crushing chamber solution for your needs. This gives you the power to reduce fines production or increase the reduction ratio; whichever makes your operations more profitable. * The Sandvik computer modeling and analysis tool must be used to determine the correct crushing chamber setup.

Product name

OPTIAGG solution

Application

Tertiary or final crushing stages. For increased final product (P80) – either reduced fines or increased size reduction.

Crusher compatibility and concave match

Optiagg L (3-wedge design) CH430: MC, M CH440: MC, M, MF CH660: MC, M, MF Optiagg S (6-wedge design) CH430: MC, M, MF CH440: MC, M, MF, F CH660: MC, M, MF, F

HIGH REDUCTION CONCAVE Our High Reduction (HR) concave – or fixed mantle – is part of our “short” chamber solutions. It has a unique shelf design that increases the crushing chamber pressure in finer applications. This unique concave with its patented step feature has proven to offer up to 10% more final product compared to conventional designs, and offers up to 19% less recirculating load, creating a more efficient crushing circuit.

Product name

High Reduction (HR) concave

Application

Finer applications: tertiary or final crushing stages. It has a unique shelf design that increases the pressure in the crushing chamber giving more reduction.

Crusher compatibility and mantle match

CH660: A, D, B, HC CH865i: A, B CH870i: A, B CH895i (CH880): A, B, HC

M9 ALLOY MIX We have a newer premium alloy mix - M9 - that offers our highest resistance to abrasive rock, but has a slightly lower resistance to shock and impact compared to the M1. The M9 mix is used for our CS and CH crushing chamber solutions. You’ll get up to 20% longer lifetime, resulting in more uptime and lower operating costs with our premium alloy solutions.

Crushing Chamber Application Guide

75


CH (H-TYPE) CONE GUIDE

CH420 (H2000) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 106

18

155

20 22 25

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC

FILLER RING*

A

B

EF

HC

442.9569-01

M1

442.9698-01

442.6197-01

n/c

n/c

-

442.9569-02

M2

442.9698-02

442.6197-02

n/c

n/c

-

442.9569-03

M7

442.9698-03

442.6197-04

n/c

n/c

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 71

18

103

20 22 25

CONCAVE

ALLOY MIX

STANDARD MANTLE

C

FILLER RING*

A

B

EF

HC

442.9587-01

M1

442.9698-01

442.6197-01

n/c

n/c

442.9596-01

442.9587-02

M2

442.9698-02

442.6197-02

n/c

n/c

442.9596-01

442.9587-03

M7

442.9698-03

442.6197-04

n/c

n/c

442.9596-01

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 61 70 (HC)

76 88 (HC)

18 20 22 25 28

CONCAVE

ALLOY MIX

M

76

STANDARD MANTLE

FILLER RING*

A

B

EF

HC

442.9586-01

M1

n/c

442.6197-01

n/c

442.9761-01

442.9596-01

442.9586-02

M2

n/c

442.6197-02

n/c

442.9761-02

442.9596-01

442.9586-03

M7

n/c

442.6197-04

n/c

442.9761-03

442.9596-01

Crushing Chamber Application Guide


CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 47 58 (HC)

18

58 72 (HC)

20 22 25 28

CONCAVE

ALLOY MIX

STANDARD MANTLE

MF

FILLER RING*

A

B

EF

HC

442.9585-01

M1

n/c

442.6197-01

n/c

442.9761-01

442.9596-01

442.9585-02

M2

n/c

442.6197-02

n/c

442.9761-02

442.9596-01

442.9585-03

M7

n/c

442.6197-04

n/c

442.9761-03

442.9596-01

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 34 45 (HC)

18

42 56 (HC)

20 22 25 28

CONCAVE

ALLOY MIX

STANDARD MANTLE

F

FILLER RING*

A

B

EF

HC

442.9584-01

M1

442.9698-01

442.6197-01

n/c

442.9761-01

442.9596-01

442.9584-02

M2

442.9698-02

442.6197-02

n/c

442.9761-02

442.9596-01

442.9584-03

M7

442.9698-03

442.6197-04

n/c

442.9761-03

442.9596-01

CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 18 25

31

20 22 25 28

CONCAVE

ALLOY MIX

EF

STANDARD MANTLE

FILLER RING*

A

B

EF

HC

442.9583-01

M1

n/c

n/c

442.7000-01

n/c

442.9596-01

442.9583-02

M2

n/c

n/c

442.7000-02

n/c

442.9596-01

442.9583-03

M7

n/c

n/c

442.7000-03

n/c

442.9596-01

MANTLE TYPE =A

= Heavy Choke (HC)

= B or HC

=B

= A or HC

= EF

* Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

77


CH (H-TYPE) CONE GUIDE

H2000 Concaves and mantles for Sandvik cone crushers with the C2 top shell (H2000:05) produced before February 1997.

CONCAVE

ALLOY MIX

C

FILLER RING

B

442.6221-01

M1

442.6197-01

-

442.6221-02

M2

442.6197-02

-

442.6221-03

M7

442.6197-04

-

CONCAVE

ALLOY MIX

MC

STANDARD MANTLE

FILLER RING

B

452.3044-001

M1

442.6197-01

-

452.3044-002

M2

442.6197-02

-

452.3044-003

M7

442.6197-04

-

CONCAVE

ALLOY MIX

M

STANDARD MANTLE

FILLER RING

B

442.6428-01

M1

442.6197-01

-

442.6428-02

M2

442.6197-02

-

442.6428-04

M7

442.6197-04

-

CONCAVE

ALLOY MIX

F

78

STANDARD MANTLE

STANDARD MANTLE

FILLER RING

B

442.6580-01

M1

442.6197-01

-

442.6580-02

M2

442.6197-02

-

Crushing Chamber Application Guide


CH420 (H2000) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

FLEXIFEED MANTLE C.S.S. (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

13 16 EC

18

87

20 22 25 13 16

C

18

58

20 22 25

MANTLE

ALLOY MIX

CONCAVE

FF

FILLER RING

EC

C

BG00143591-01

M1

442.9569-01

442.9587-01*

442.9569-01

BG00143591-02

M2

442.9569-02

442.9587-02*

442.9569-01

BG00143591-03

M7

442.9569-04

442.9587-03*

442.9569-01

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

Crushing Chamber Application Guide

79


CH (H-TYPE) CONE GUIDE

CH430 (H3800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 147

214

25 29 32 34

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC

FILLER RING**

A

S

B

EF

HC

442.8249-01

M1

442.7988-01

452.1171-001

442.7989-01

n/c

n/c

-

442.8249-02

M2

442.7988-02

452.1171-002

442.7989-02

n/c

n/c

-

442.8249-03

M7

442.7988-03

452.1171-003

442.7989-03

n/c

n/c

-

442.8249-05

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

n/c

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 116

168

25 29 32 34

CONCAVE

ALLOY MIX

C

80

STANDARD MANTLE A

S

B

FILLER RING** EF

HC

442.8248-01

M1

442.7988-01

452.1171-001

442.7989-01

n/c

n/c

442.8245-01

442.8248-02

M2

442.7988-02

452.1171-002

442.7989-02

n/c

n/c

442.8245-01

442.8248-03

M7

442.7988-03

452.1171-003

442.7989-03

n/c

n/c

442.8245-01

442.8248-05

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

n/c

442.8245-01

Crushing Chamber Application Guide


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 103 116 (HC)

25

129 145 (HC)

29 32 34 36

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC 442.8247-01

M1

FILLER RING**

A

S

B

EF

HC

442.7988-01

452.1171-001

442.7989-01

n/c

n/c

442.8245-01

442.8247-02

M2

442.7988-02

452.1171-002

442.7989-02

n/c

n/c

442.8245-01

442.8247-03

M7

442.7988-03

452.1171-003

442.7989-03

n/c

n/c

442.8245-01

442.8247-05

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

n/c

442.8245-01

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 81 94 (HC)

101 118 (HC)

25 29 32 34 36

CONCAVE

ALLOY MIX

M

STANDARD MANTLE A

S

B

FILLER RING** EF

HC

442.8246-01

M1

442.7988-01

452.1171-001

442.7989-01

n/c

442.9759-01

442.8008-01

442.8246-02

M2

442.7988-02

452.1171-002

442.7989-02

n/c

442.9759-02

442.8008-01

442.8246-03

M7

442.7988-03

452.1171-003

442.7989-03

n/c

442.9759-03

442.8008-01

442.8246-05

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

442.9759-05

442.8008-01

MANTLE TYPE =A

=B

= A or HC

=S

= Heavy Choke (HC)

= S or HC

= B or HC

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

81


CH (H-TYPE) CONE GUIDE

CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 69 82 (HC)

25

86 103 (HC)

29 32 34 36

CONCAVE

ALLOY MIX

STANDARD MANTLE

MF 452.1216-001

M1

FILLER RING**

A

S

B

EF

HC

442.7988-01

452.1171-001

442.7989-01

n/c

442.9759-01

442.8008-01

452.1216-002

M2

442.7988-02

452.1171-002

442.7989-02

n/c

442.9759-02

442.8008-01

452.1216-003

M7

442.7988-03

452.1171-003

442.7989-03

n/c

442.9759-03

442.8008-01

452.1216-005

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

442.9759-05

442.8008-01

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 49 56 (HC)

62 70 (HC)

25 29 32 34 36

CONCAVE

ALLOY MIX

F

82

STANDARD MANTLE A

S

B

FILLER RING** EF

HC

442.8251-01

M1

442.7988-01

452.1171-001

442.7989-01

n/c

442.9759-01

442.8008-01

442.8251-02

M2

442.7988-02

452.1171-002

442.7989-02

n/c

442.9759-02

442.8008-01

442.8251-03

M7

442.7988-03

452.1171-003

442.7989-03

n/c

442.9759-03

442.8008-01

442.8251-05

M9*

442.7988-05

452.1171-005

442.7989-05

n/c

442.9759-05

442.8008-01

Crushing Chamber Application Guide


CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

16 19 22 33

25

42

29 32 34 36

CONCAVE

ALLOY MIX

STANDARD MANTLE

EF

FILLER RING**

A

S

B

EF

HC

442.8630-01

M1

n/c

n/c

n/c

452.1502-001

n/c

442.8245-01

442.8630-02

M2

n/c

n/c

n/c

452.1502-002

n/c

442.8245-01

442.8630-03

M7

n/c

n/c

n/c

452.1502-003

n/c

442.8245-01

442.8630-05

M9*

n/c

n/c

n/c

452.1502-005

n/c

442.8245-01

MANTLE TYPE =A

=B

= A or HC

= B or HC

=S

= Heavy Choke (HC)

= S or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

83


CH (H-TYPE) CONE GUIDE

CH430 (H3800) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

FLEXIFEED MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

16 19 22 EC

121

25 29 32 34 16 19 22

C

95

25 29 32 34 16 19 22

MC

25

66

29 32 34 36

MANTLE

ALLOY MIX

CONCAVE

FF

EC

C

MC

FILLER RING

452.6115-001

M1

442.8249-01

442.8248-01*

442.8247-01*

442.8245-01

452.6115-002

M2

442.8249-02

442.8248-02*

442.8247-02*

442.8245-01

452.6115-003

M7

442.8249-03

442.8248-03*

442.8247-03*

442.8245-01

452.6115-005

M9

442.8249-05

442.8248-05*

442.8247-05*

442.8245-01

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

84

Crushing Chamber Application Guide

41


OPTIAGG SOLUTION* Our innovative Optiagg solution is our latest premium offering, giving you up to 30% more desired product (whether it is a P80 or a target fraction). The real difference is the applied computer modeling and analysis, which is necessary to find the optimal crushing chamber solution for your needs. This gives you the option to reduce fines production or increase the reduction ratio; whichever makes your operation more profitable. Our Optiagg kits come with all necessary parts needed to get a premium crushing chamber upgrade, such as the Optiagg mantle, concave, burning ring, backing compound, scrapers and more.

OPTIAGG L KIT

M1

M2

MC

BG00391494

BG00391497

OPTIAGG S KIT

M

BG00391499

BG00391502

M

BG00391498

BG00391501

MF

-

-

MF

BG00391504

BG00391506

MC

M1

M2

BG00391493

BG00391496

OPTIAGG S: 6-WEDGE DESIGN OPTIAGG L: 3-WEDGE DESIGN

* The Sandvik computer modeling and analysis tool must be used to determine the correct crushing chamber setup.

CUSTOMIZED LINERS CUSTOMIZED EF CONCAVE (442.9349) In applications with little to no wear in the top section of the crushing chamber, the feed opening can decrease when the chamber is wearing out. This special EF-concave has a more vertical upper section, maintaining the feed opening given these feed conditions. Available as 442.9349-01 (M1), 442.9349-02 (M2) and 442.9349-03 (M7). CUSTOMIZED B-MANTLE (442.9627) When running with large throws and settings, this special B-mantle can offer a more optimized crushing point for these applications. It helps reduce unwanted mantle wear patterns like skip slope formation. Available as 442.9627-01 (M1).

Crushing Chamber Application Guide

85


CH (H-TYPE) CONE GUIDE

CH440 (H4800, H4000) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC Top Grip

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 171

28

250

32 36 40 44 CONCAVE

ALLOY MIX

STANDARD MANTLE

EC Top Grip

FILLER RING**

A

B

EF

HC

452.3027-001

M1

442.7225-01

442.7230-01

n/c

n/c

-

452.3027-002

M2

442.7225-02

442.7230-02

n/c

n/c

-

452.3027-003

M7

442.7225-03

442.7230-03

n/c

n/c

-

452.3027-005

M9*

442.7225-05

442.7230-05

n/c

n/c

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 140

204

28 32 36 40 44

CONCAVE

ALLOY MIX

C

86

STANDARD MANTLE

FILLER RING**

A

B

EF

HC

442.8421-01

M1

442.7225-01

442.7230-01

n/c

n/c

-

442.8421-02

M2

442.7225-02

442.7230-02

n/c

n/c

-

442.8421-03

M7

442.7225-03

442.7230-03

n/c

n/c

-

442.8421-05

M9*

442.7225-05

442.7230-05

n/c

n/c

-

Crushing Chamber Application Guide


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 126 148 (HC)

157 185 (HC)

28 32 36 40 44

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC

FILLER RING**

A

B

EF

HC

442.8420-01

M1

442.7225-01

442.7230-01

n/c

442.9073-01

442.7485-01

442.8420-02

M2

442.7225-02

442.7230-02

n/c

442.9073-02

442.7485-01

442.8420-03

M7

442.7225-03

442.7230-03

n/c

442.9073-03

442.7485-01

442.8420-05

M9*

442.7225-05

442.7230-05

n/c

442.9073-05

442.7485-01

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 99 117 (HC)

124 146 (HC)

28 32 36 40 44

CONCAVE

ALLOY MIX

M

STANDARD MANTLE

FILLER RING**

A

B

EF

HC

442.8419-01

M1

442.7225-01

442.7230-01

n/c

442.9073-01

442.7485-01

442.8419-02

M2

442.7225-02

442.7230-02

n/c

442.9073-02

442.7485-01

442.8419-03

M7

442.7225-03

442.7230-03

n/c

442.9073-03

442.7485-01

442.8419-05

M9*

442.7225-05

442.7230-05

n/c

442.9073-05

442.7485-01

MANTLE TYPE =A

=B

= Heavy Choke (HC)

= A or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

87


CH (H-TYPE) CONE GUIDE

CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 78 96 (HC)

98 120 (HC)

28 32 36 40 44

CONCAVE

ALLOY MIX

STANDARD MANTLE

MF

FILLER RING**

A

B

EF

HC

442.8418-01

M1

442.7225-01

442.7230-01

n/c

442.9073-01

442.7484-01

442.8418-02

M2

442.7225-02

442.7230-02

n/c

442.9073-02

442.7484-01

442.8418-03

M7

442.7225-03

442.7230-03

n/c

442.9073-03

442.7484-01

442.8418-05

M9*

442.7225-05

442.7230-05

n/c

442.9073-05

442.7484-01

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 66 79 (HC)

83 99 (HC)

28 32 36 40 44

CONCAVE

ALLOY MIX

F

88

STANDARD MANTLE

FILLER RING**

A

B

EF

HC

442.8417-01

M1

442.7225-01

442.7230-01

n/c

442.9073-01

442.7484-01

442.8417-02

M2

442.7225-02

442.7230-02

n/c

442.9073-02

442.7484-01

442.8417-03

M7

442.7225-03

442.7230-03

n/c

442.9073-03

442.7484-01

442.8417-05

M9*

442.7225-05

442.7230-05

n/c

442.9073-05

442.7484-01

Crushing Chamber Application Guide


CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 37

28

47

32 36 40 44

CONCAVE

ALLOY MIX

STANDARD MANTLE

EF

FILLER RING**

A

B

EF

HC

442.8416-01

M1

n/c

n/c

442.8039-01

n/c

442.7485-01

442.8416-02

M2

n/c

n/c

442.8039-02

n/c

442.7485-01

442.8416-03

M7

n/c

n/c

442.8039-03

n/c

442.7485-01

442.8416-05

M9*

n/c

n/c

442.8039-05

n/c

442.7485-01

MANTLE TYPE =A

=B

= Heavy Choke (HC)

= A or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

89


CH (H-TYPE) CONE GUIDE

CH440 (H4800, H4000) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

FLEXIFEED MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

16 20 24 EC Top Grip

28

141

32 36 40 44 16 20 24 C

28

115

32 36 40 44 16 20 24 MC

28

80

32 36 40 44

MANTLE

ALLOY MIX

FF (A)

CONCAVE EC Top Grip

C

MC

FILLER RING

452.5271-001

M1

452.3027-001

442.8421-01

442.8420-01*

442.7485-01

452.5271-002

M2

452.3027-002

442.8421-02

442.8420-02*

442.7485-01

452.5271-003

M7

452.3027-003

442.8421-03

442.8420-03*

442.7485-01

452.5271-005

M9

452.3027-005

442.8421-05

442.8420-05*

442.7485-01

MANTLE

ALLOY MIX

FF (B)

CONCAVE EC Top Grip

C

MC

FILLER RING

452.6063-001

M1

452.3027-001

442.8421-01

442.8420-01*

442.7485-01

452.6063-002

M2

452.3027-002

442.8421-02

442.8420-02*

442.7485-01

452.6063-003

M7

452.3027-003

442.8421-03

442.8420-03*

442.7485-01

452.6063-005

M9

452.3027-005

442.8421-05

442.8420-05*

442.7485-01

MANTLE TYPE = FF (A)

90

= FF (B)

Crushing Chamber Application Guide

* Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle


OPTIAGG SOLUTION* Our innovative Optiagg solution is our latest premium offering, giving you up to 30% more desired product (whether it is a P80 or a target fraction). The real difference is the applied computer modeling and analysis, which is necessary to find the optimal crushing chamber solution for your needs. This gives you the option to reduce fines production or increase the reduction ratio; whichever makes your operations more profitable. Our Optiagg kits come with all necessary parts needed to get a premium crushing chamber upgrade, such as the Optiagg mantle, concave, burning ring, backing compound, scrapers, and more.

OPTIAGG L KIT

M1

M2

MC

BG00391543

BG00391545

OPTIAGG S KIT

M

BG00391547

BG00391549

M

BG00391546

BG00391548

MF

BG00391551

BG00391553

MF

BG00391550

BG00391552

F

BG00391555

BG00391557

F

BG00391554

BG00391556

MC

M1

M2

BG00391542

BG00391544

OPTIAGG S: 6-WEDGE DESIGN OPTIAGG L: 3-WEDGE DESIGN

* The Sandvik computer modeling and analysis tool must be used to determine the correct crushing chamber setup.

CUSTOMIZED LINERS CUSTOMIZED “SHORT” CONCAVES – M (BG01223669) AND MF (452.4883) These special “short” concaves have been developed to increase the crushing forces within the chamber to achieve a higher size reduction with smaller feed sizes. The M-concave is available as BG01223669-01 (M1), BG01223669-02 (M2), BG01223669-03 (M7) and BG01223669-05 (M9). The MF-concave is available as 452.4883-001 (M1), 452.4883-002 (M2), 452.4883-003 (M7) and 452.4883-005 (M9). The concaves are combined with our standard mantles: A, B and HC. CUSTOMIZED F CONCAVE (452.2388) In applications with little to no wear in the top section of the crushing chamber, the feed opening can decrease when the chamber is wearing out. This special F-concave has a more vertical upper section and maintains the feed opening given these feed conditions. Available as 452.2388-001 (M1) and 452.2388-002 (M2). CUSTOMIZED EF-MANTLE (452.9209) To increase the life length of the last step, this shelf is machined off and the surface is hard welded. This new opening allows for a better flow of material into the chamber. Available as 442.9209-01 (M1) and 442.9209-02 (M2). CUSTOMIZED EF-MANTLE (452.3103) The last step on this special EF-mantle has been machined to allow for up to 25% larger feed sizes. Available as 452.3103-001 (M1), 452.3103-002 (M2) and 452.3103-003 (M7). CUSTOMIZED HC-MANTLE (442.9601) This special HC-mantle is used in applications that require a larger feed opening compared to an A-mantle. The lower step is removed, offering higher capacity with a new liner set. Available as 442.9601-01 (M1) and 442.9601-02 (M2). Crushing Chamber Application Guide

91


CH (H-TYPE) CONE GUIDE

CH540 STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC Top Grip

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

24 28 32 145

36

211

40 44 48 52 CONCAVE

ALLOY MIX

STANDARD MANTLE

EC Top Grip

FILLER RING**

A

B

EF

-

452.8358-001

M1

452.8432-001

452.8338-001

n/c

-

452.8358-002

M2

452.8432-002

452.8338-002

n/c

-

452.8358-003

M7

452.8432-003

452.8338-003

n/c

-

452.8358-005

M9

452.8432-005

452.8338-005

n/c

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

24 28 32 105

153

36 40 44 48 52

CONCAVE

ALLOY MIX

C

92

STANDARD MANTLE

FILLER RING**

A

B

EF

452.8512-001

M1

452.8432-001

452.8338-001

n/c

BG00247880

452.8512-002

M2

452.8432-002

452.8338-002

n/c

BG00247880

452.8512-003

M7

452.8432-003

452.8338-003

n/c

BG00247880

452.8512-005

M9

452.8432-005

452.8338-005

n/c

BG00247880

Crushing Chamber Application Guide

41


CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

24 28 32 74

36

93

40 44 48 52 CONCAVE

ALLOY MIX

STANDARD MANTLE

M

FILLER RING**

A

B

EF

452.8513-001

M1

452.8432-001

452.8338-001

n/c

BG00248423

452.8513-002

M2

452.8432-002

452.8338-002

n/c

BG00248423

452.8513-003

M7

452.8432-003

452.8338-003

n/c

BG00248423

452.8513-005

M9

452.8432-005

452.8338-005

n/c

BG00248423

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE C.S.S. (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

24 28 32 49

36

61

40 44 48 52 CONCAVE

ALLOY MIX

F

STANDARD MANTLE

FILLER RING**

A

B

EF

452.8339-001

M1

452.8432-001

452.8338-001

n/c

BG00248423

452.8339-002

M2

452.8432-002

452.8338-002

n/c

BG00248423

452.8339-003

M7

452.8432-003

452.8338-003

n/c

BG00248423

452.8339-005

M9

452.8432-005

452.8338-003

n/c

BG00248423

MANTLE TYPE =A

=B

= EF

** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

93


CH (H-TYPE) CONE GUIDE

CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

24 28 32 38

36

48

40 44 48 52

CONCAVE

ALLOY MIX

EF

STANDARD MANTLE B

EF

452.8511-001

M1

n/c

n/c

452.8510-001

BG00248423

452.8511-002

M2

n/c

n/c

452.8510-002

BG00248423

452.8511-003

M7

n/c

n/c

452.8510-003

BG00248423

452.8511-005

M9

n/c

n/c

452.8510-005

BG00248423

MANTLE TYPE =A

=B

= EF

** Filler ring is used between the concave and the top shell n/c = not compatible

94

FILLER RING**

A

Crushing Chamber Application Guide

41


CH540 PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

FLEXIFEED MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

24 28 32 EC

36

119

40 44 48 52 24 28 32

C

36

87

40 44 48 52

MANTLE

ALLOY MIX

FF

CONCAVE

FILLER RING

EC Top Grip

C

452.9030-001

M1

452.8358-001

452.8512-001*

BG00247880

452.9030-002

M2

452.8358-002

452.8512-002*

BG00247880

452.9030-003

M7

452.8358-003

452.8512-003*

BG00247880

452.9030-005

M9

452.8358-005

452.8512-005*

BG00247880

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

CUSTOMIZED LINERS CUSTOMIZED F CONCAVE (BG01222181) This special “F-short” concave has been developed to increase the crushing forces within the chamber to achieve a higher size reduction with smaller feed sizes. This concave is available as BG01222181-01 (M1), BG01222181-02 (M2) and BG01222181-03 (M7).

Crushing Chamber Application Guide

95


CH (H-TYPE) CONE GUIDE

CH550 STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC Top Grip

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

44

48

28 32 36 172

250

40 44 48 52

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC Top Grip

FILLER RING*

A

B

452.7843-001

M1

452.7626-001

452.8602-001

-

452.7843-002

M2

452.7626-002

452.8602-002

-

452.7843-003

M7

452.7626-003

452.8602-003

-

452.7843-005

M9

452.7626-005

452.8602-005

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

28 32 36 141

205

40 44 48 52

CONCAVE

ALLOY MIX

C

96

STANDARD MANTLE A

FILLER RING* B

452.8500-001

M1

452.7626-001

452.8602-001

452.7388-001

452.8500-002

M2

452.7626-002

452.8602-002

452.7388-001

452.8500-003

M7

452.7626-003

452.8602-003

452.7388-001

452.8500-005

M9

452.7626-005

452.8602-005

452.7388-001

Crushing Chamber Application Guide


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS. (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

44

48

28 32 127

36

159

40 44 48 52

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC

FILLER RING*

A

B

452.8496-001

M1

452.7626-001

452.8602-001

452.7388-001

452.8496-002

M2

452.7626-002

452.8602-002

452.7388-001

452.8496-003

M7

452.7626-003

452.8602-003

452.7388-001

452.8496-005

M9

452.7626-005

452.8602-005

452.7388-001

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

28 32 97

36

121

40 44 48 52

CONCAVE

ALLOY MIX

M

STANDARD MANTLE

FILLER RING*

A

B

452.8601-001

M1

452.7626-001

452.8602-001

452.7386-001

452.8601-002

M2

452.7626-002

452.8602-002

452.7386-001

452.8601-003

M7

452.7626-003

452.8602-003

452.7388-001

452.8601-005

M9

452.7626-005

452.8602-005

452.7386-001

MANTLE TYPE =A

=B

* Filler ring is used between the concave and the top shell

Crushing Chamber Application Guide

97


CH (H-TYPE) CONE GUIDE

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

28 32 36 73

40

92

44 48 52 CONCAVE

ALLOY MIX

F

STANDARD MANTLE A

452.8600-001

M1

452.7626-001

452.8602-001

452.7386-001

452.8600-002

M2

452.7626-002

452.8602-002

452.7386-001

452.8600-003

M7

452.7626-003

452.8602-003

452.7388-001

452.8600-005

M9

452.7626-005

452.8602-005

452.7386-001

MANTLE TYPE =A

=B

* Filler ring is used between the concave and the top shell

98

FILLER RING* B

Crushing Chamber Application Guide

44

48


CH550 PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

FLEXIFEED MANTLE CSS (mm) 4

5

6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

28 32 36 EC Top Grip

141

40 44 48 52 28 32 36

C

116

40 44 48 52 28 32 36

MC

81

40 44 48 52

MANTLE

ALLOY MIX

FF

CONCAVE

FILLER RING

EC Top Grip

C

MC

BG00133846-01

M1

452.7843-001

452.8500-001*

452.8496-001*

452.7388-001

BG00133846-02

M2

452.7843-002

452.8500-002*

452.8496-002*

452.7388-001

BG00133846-03

M7

452.7843-003

452.8500-003*

452.8496-003*

452.7388-001

BG00133846-05

M9

452.7843-005

452.8500-005*

452.8496-005*

452.7388-001

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

Crushing Chamber Application Guide

99


CH (H-TYPE) CONE GUIDE

CH660 (H6800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 220

321

32 36 40 44 48

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC

FILLER RING**

A

D

B

EF

HC

442.8813-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

n/c

-

442.8813-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

n/c

-

442.8813-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

n/c

-

442.8813-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

n/c

-

ECi - our EC concave with integrated, cast-fastening ears: BG00420396 (M1); BG00420397 (M2).

CONCAVE CX

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 189

275

32 36 40 44 48

CONCAVE

ALLOY MIX

CX

STANDARD MANTLE

FILLER RING**

A

D

B

EF

HC

442.9230-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

n/c

-

442.9230-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

n/c

-

442.9230-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

n/c

-

442.9230-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

n/c

-

CXi - our CX concave with integrated, cast-fastening ears: BG00420434 (M1); BG00420435 (M2).

100

Crushing Chamber Application Guide


CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 174

253

32 36 40 44 48

CONCAVE

ALLOY MIX

C

STANDARD MANTLE

FILLER RING**

A

D

B

EF

HC

442.8814-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

n/c

-

442.8814-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

n/c

-

442.8814-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

n/c

-

442.8814-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

n/c

-

CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 159 167 (HC)

198 209 (HC)

28 32 36 40 44 48

CONCAVE

ALLOY MIX

MC

STANDARD MANTLE

FILLER RING**

A

D

B

EF

HC

442.8815-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

442.9760-01

442.8823-01

442.8815-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

442.9760-02

442.8823-01

442.8815-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

442.9760-03

442.8823-01

442.8815-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

442.9760-05

442.8823-01

MANTLE TYPE =A

=B

= A or HC

=D

= Heavy Choke (HC)

= D or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

101


CH (H-TYPE) CONE GUIDE

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 124 133 (HC)

32

155 166 (HC)

36 40 44 48 50

CONCAVE

ALLOY MIX

STANDARD MANTLE

M

FILLER RING**

A

D

B

EF

HC

442.8816-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

442.9760-01

442.8823-01

442.8816-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

442.9760-02

442.8823-01

442.8816-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

442.9760-03

442.8823-01

442.8816-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

442.9760-05

442.8823-01

CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 106 111 (HC)

133 139 (HC)

32 36 40 44 48 50

CONCAVE

ALLOY MIX

MF

102

STANDARD MANTLE A

D

B

FILLER RING** EF

HC

442.8817-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

442.9760-01

442.8863-01

442.8817-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

442.9760-02

442.8863-01

442.8817-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

442.9760-03

442.8863-01

442.8817-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

442.9760-05

442.8863-01

Crushing Chamber Application Guide


CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 77 86 (HC)

96 107 (HC)

32 36 40 44 48 50

CONCAVE

ALLOY MIX

F

STANDARD MANTLE

FILLER RING**

A

D

B

EF

HC

442.8818-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

442.9760-01

442.8863-01

442.8818-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

442.9760-02

442.8863-01

442.8818-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

442.9760-03

442.8863-01

442.8818-05

M9*

442.8819-05

442.8821-05

442.8820-05

n/c

442.9760-05

442.8863-01

CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 50

32

62

36 40 44 48 50

CONCAVE

ALLOY MIX

EF

STANDARD MANTLE

FILLER RING**

A

D

B

EF

HC

452.0832-001

M1

n/c

n/c

n/c

452.0820-001

n/c

-

452.0832-002

M2

n/c

n/c

n/c

452.0820-002

n/c

-

452.0832-003

M7

n/c

n/c

n/c

452.0820-003

n/c

-

452.0832-005

M9*

n/c

n/c

n/c

452.0820-005

n/c

-

MANTLE TYPE =A

=B

= A or HC

=D

= Heavy Choke (HC)

= D or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

103


CH (H-TYPE) CONE GUIDE

CH660 (H6800) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

10 18 20 24 28

EC/ECi

181

32 36 40 44 48 18 20 24 28

CX/CXi

155

32 36 40 44 48 18 20 24 28

C

143

32 36 40 44 48 18 20 24 28

MC

101

32 36 40 44 48

104

Crushing Chamber Application Guide

FLEXIFEED MANTLE CSS (mm) 13

16

19

22

25

29

32

35

38

41

44

48

51


MANTLE

ALLOY MIX

FF

CONCAVE EC

FILLER RING

ECi

CX

CXi

C

MC

452.6027-001

M1

442.8813-01 BG00420396 442.9230-01 BG00420434 442.8814-01 442.8247-01* 442.8823-01

452.6027-002

M2

442.8813-02 BG00420397 442.9230-02 BG00420435 442.8814-02 442.8247-02* 442.8823-01

452.6027-003

M7

442.8813-03

-

442.9230-03

-

442.8814-03 442.8247-03* 442.8823-01

452.6027-005

M9

442.8813-05

-

442.9230-05

-

442.8814-05 442.8247-05* 442.8823-01

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

HIGH REDUCTION - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our High Reduction concave has a unique shelf design that increases the crushing chamber pressure in finer applications. This patented design feature has proven to offer up to 10% more final product compared to conventional designs, and offers up to 19% less recirculating load, creating a more efficient crushing circuit.

CONCAVE HR

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

51

18 20 24 28 67 53 (HC)

32

83 67 (HC)

36 40 44 48 50

CONCAVE

ALLOY MIX

HR

STANDARD MANTLE

FILLER RING

A

D

B

EF

HC

BG00417468-01

M1

442.8819-01

442.8821-01

442.8820-01

n/c

442.9760-01

-

BG00417468-02

M2

442.8819-02

442.8821-02

442.8820-02

n/c

442.9760-02

-

BG00417468-03

M7

442.8819-03

442.8821-03

442.8820-03

n/c

442.9760-03

-

BG00417468-05

M9

442.8819-05

442.8821-05

442.8820-05

n/c

442.9760-05

-

MANTLE TYPE =A

=B

= A or HC

=D

= Heavy Choke (HC)

= D or HC

n/c = not compatible

Crushing Chamber Application Guide

105


CH (H-TYPE) CONE GUIDE

OPTIAGG SOLUTION* Our innovative Optiagg solution is our latest premium offering, giving you up to 30% more desired product (whether it is a P80 or a target fraction). The real difference is the applied computer modeling and analysis, which is necessary to find the optimal crushing chamber solution for your needs. This gives you the option to reduce fines production or increase the reduction ratio; whichever makes your operations more profitable. Our Optiagg kits come with all necessary parts needed to get a premium crushing chamber upgrade, such as the Optiagg mantle, concave, burning ring, backing compound, scrapers and more.

OPTIAGG L KIT MC

M1

M2

M1

M2

BG00391965

BG00391973

OPTIAGG S KIT MC

BG00391958

BG00391971

M

BG00391976

BG00391978

M

BG00391975

BG00391977

MF

BG00391980

BG00391983

MF

BG00391979

BG00391981

F

BG00391984

BG00391987

OPTIAGG S: 6-WEDGE DESIGN OPTIAGG L: 3-WEDGE DESIGN

* The Sandvik computer modeling and analysis tool must be used to determine the correct crushing chamber setup.

106

Crushing Chamber Application Guide


CUSTOMIZED LINERS CUSTOMIZED D-MANTLE (452.1543) When producing railway ballast, wear on the support ring can appear due to the large throws and settings. To reduce this unwanted wear, this special D-mantle creates more distance between the support ring and the bottom end of the mantle. The wear profile of the crushing chamber will change slightly with this customized solution. Available as 452.1543-001 (M1), 452.1543-002 (M2), 452.1543-003 (M7) and 452.1543-005 (M9). CUSTOMIZED B-MANTLE (452.1542) When producing railway ballast, wear on the support ring can appear due to the large throws and settings. To reduce this unwanted wear, this special B-mantle creates more distance between the support ring and the bottom end of the mantle. The wear profile of the crushing chamber will change slightly with this customized solution. Available as 442.1542-001 (M1) and 442.1542-002 (M2). CUSTOMIZED EF-MANTLE (452.0455) In some applications, there is a very high wear rate in the steps of the EF-mantle. To increase life length, we customized this EF-mantle with gussets to prevent wear in the top section of the mantle. Available as 452.0455-001 (M1). CUSTOMIZED EF-MANTLE (BG01236659) The last step on this special EF-mantle has been machined to allow for up to 10 mm larger feed sizes compared to the standard EF mantle (452.0820). Available as BG01236659-01 (M1), BG01236659-02 (M2), BG01236659-03 (M7) and BG01236659-05 (M9). CUSTOMIZED EF-MANTLE (BG01237520) This EF mantle has been machined to allow for up to 10% longer flakes sizes. Available as BG01237520-01 (M1), BG01237520-02 (M2), BG01237520-03 (M7) and BG01237520-05 (M9). CUSTOMIZED EF-CONCAVE (BG01225329) In applications with little to no wear in the top section of the crushing chamber, the feed opening can decrease when the chamber is wearing out. This special EF-concave has a more vertical upper section and maintains the feed opening given these feed conditions. Available as BG01225329-01 (M1), BG01225329-02 (M2), BG01225329-03 (M7) and BG01225329-05 (M9). CUSTOMIZED HC-MANTLE (442.9990) This special HC-mantle is used in applications that require a larger feed opening compared to an A-mantle. The lower step is removed and gives higher capacity with a new liner set. Available as 442.9990-01 (M1) and 442.9990-02 (M2).

Crushing Chamber Application Guide

107


CH (H-TYPE) CONE GUIDE

CH860i (CH860) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC Top Grip

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

48

51

30 34 38 42 46 216

315

50 54 58 62 66 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC Top Grip

FILLER RING**

A

B

452.8231-001

M1

452.8232-001

452.8233-001

-

452.8231-002

M2

452.8232-002

452.8233-002

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

30 34 38 42 46 181

263

50 54 58 62 66 70

CONCAVE

ALLOY MIX

C

108

STANDARD MANTLE

FILLER RING**

A

B

452.8238-001

M1

452.8232-001

452.8233-001

-

452.8238-002

M2

452.8232-002

452.8233-002

-

Crushing Chamber Application Guide


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

30 34 38 42 46 157

196

50 54 58 62 66 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC

FILLER RING**

A

B

452.8239-001

M1

452.8232-001

452.8233-001

452.7883-001

452.8239-002

M2

452.8232-002

452.8233-002

452.7883-001

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

30 34 38 42 46 122

152

50 54 58 62 66 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

M

FILLER RING**

A

B

452.8240-001

M1

452.8232-001

452.8233-001

452.8281-001

452.8240-002

M2

452.8232-002

452.8233-002

452.8281-001

MANTLE TYPE =A

=B

** Filler ring is used between the concave and the top shell

Crushing Chamber Application Guide

109


CH (H-TYPE) CONE GUIDE

CH860i (CH860) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

10 30 34 38 42 46

EC Top Grip

178

50 54 58 62 66 70 30 34 38 42 46

C

149

50 54 58 62 66 70 30 34 38 42 46

MC

100

50 54 58 62 66 70

110

Crushing Chamber Application Guide

FLEXIFEED MANTLE CSS (mm) 13

16

19

22

25

29

32

35

38

41

44

48

51


MANTLE

ALLOY MIX

FF

CONCAVE

FILLER RING

EC

C

MC

452.8243-001

M1

452.8231-001

452.8238-001

452.8239-001*

452.7883-001

452.8243-002

M2

452.8231-002

452.8238-002

452.8239-002*

452.7883-001

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

Crushing Chamber Application Guide

111


CH (H-TYPE) CONE GUIDE

CH865i (CH865) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

51

30 34 38 42 46 85

97

50 54 58 62 66 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

F

FILLER RING

A

B

EF

452.8242-001

M1

n/c

n/c

452.8236-001

-

452.8242-002

M2

n/c

n/c

452.8236-002

-

CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

48

30 34 38 42 46 63

72

50 54 58 62 66 70

CONCAVE

ALLOY MIX

EF

FILLER RING

B

EF

452.8235-001

M1

n/c

n/c

452.8236-001

-

452.8235-002

M2

n/c

n/c

452.8236-002

-

MANTLE TYPE = EF n/c = not compatible

112

STANDARD MANTLE A

Crushing Chamber Application Guide

51


Crushing Chamber Application Guide

113


CH (H-TYPE) CONE GUIDE

CH865i (CH865) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

OVERSIZE BREAKER - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Oversize Breaker (OB) mantle is engineered for tertiary or final crushing applications. It has a varying feed opening that increases the allowable top size in finer crushing chambers, and helps to prevent bridging from oversized process material.

CONCAVES

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

FLEXIFEED MANTLE CSS (mm) 10

13

16

19

22

25

29

32

35

38

41

44

30 34 38 42 46 F

68

97

50 54 58 62 66 70 30 34 38 42 46

EF

51

72

50 54 58 62 66 70

MANTLE

ALLOY MIX

OB

FILLER RING EF

452.8244-001

M1

452.8242-001

452.8235-001

-

452.8244-002

M2

452.8242-002

452.8235-002

-

MANTLE TYPE = OB

114

CONCAVE F

Crushing Chamber Application Guide

48

51


HIGH REDUCTION - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our High Reduction concave has a unique shelf design that increases the crushing chamber pressure in finer applications. This patented design feature has proven to offer up to 10% more final product compared to conventional designs, and offers up to 19% less recirculating load, creating a more efficient crushing circuit.

CONCAVE HR

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 6

8

10

13

16

19

22

25

29

32

35

38

41

44

48

51

30 34 38 42 46 75

94

50 54 58 62 66 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

HR

FILLER RING

A

B

EF

OB

452.8446-001

M1

452.8232-001

452.8233-001

n/c

n/c

-

452.8446-002

M2

452.8232-002

452.8233-002

n/c

n/c

-

MANTLE TYPE =A

=B

n/c = not compatible

Crushing Chamber Application Guide

115


CH (H-TYPE) CONE GUIDE

CH870i (CH870, H7800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC Top Grip

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 240

47

350

52 57 62 68

CONCAVE

ALLOY MIX

STANDARD MANTLE

EC Top Grip

FILLER RING**

A

B

EF

BG00239713-01

M1

452.0837-001

452.0872-001

n/c

452.0891-901

BG00239713-02

M2

452.0837-002

452.0872-002

n/c

452.0891-901

BG00239713-05

M9*

452.0837-005

452.0872-005

n/c

452.0891-901

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

32 37 42 197

287

47 52 57 62 68

CONCAVE

ALLOY MIX

C

FILLER RING**

B

EF

M1

452.0837-001

452.0872-001

n/c

452.2269-901

452.2255-002

M2

452.0837-002

452.0872-002

n/c

452.2269-901

452.2255-005

M9*

452.0837-005

452.0872-005

n/c

452.2269-901

452.2255-001

116

STANDARD MANTLE A

Crushing Chamber Application Guide

70


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 162

47

236

52 57 62 68

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC

FILLER RING**

A

B

EF

452.2253-001

M1

452.0837-001

452.0872-001

n/c

452.2269-901

452.2253-002

M2

452.0837-002

452.0872-002

n/c

452.2269-901

452.2253-005

M9*

452.0837-005

452.0872-005

n/c

452.2269-901

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 147

47

184

52 57 62 68

CONCAVE

ALLOY MIX

STANDARD MANTLE

M

FILLER RING**

A

B

EF

452.1754-001

M1

452.0837-001

452.0872-001

n/c

452.0898-901

452.1754-002

M2

452.0837-002

452.0872-002

n/c

452.0898-901

452.1754-005

M9*

452.0837-005

452.0872-005

n/c

452.0898-901

MANTLE TYPE =A

=B

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

117


CH (H-TYPE) CONE GUIDE

CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 47 86

52

108

57 62 68 74 80

CONCAVE

ALLOY MIX

STANDARD MANTLE

MF

FILLER RING**

A

B

EF

452.0842-001

M1

n/c

n/c

452.0844-001

452.0898-901

452.0842-002

M2

n/c

n/c

452.0844-002

452.0898-901

452.0842-005

M9*

n/c

n/c

452.0844-005

452.0898-901

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

32 37 42 47 79

99

52 57 62 68 74 80

CONCAVE

ALLOY MIX

F

118

STANDARD MANTLE

FILLER RING**

A

B

EF

452.0841-001

M1

n/c

n/c

452.0844-001

452.0898-901

452.0841-002

M2

n/c

n/c

452.0844-002

452.0898-901

452.0841-005

M9*

n/c

n/c

452.0844-005

452.0898-901

Crushing Chamber Application Guide

70


CONCAVE EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 47 70

52

88

57 62 68 74 80

CONCAVE

ALLOY MIX

STANDARD MANTLE

EF

FILLER RING**

A

B

EF

452.0840-001

M1

n/c

n/c

452.0844-001

452.0898-901

452.0840-002

M2

n/c

n/c

452.0844-002

452.0898-901

452.0840-005

M9*

n/c

n/c

452.0844-005

452.0898-901

MANTLE TYPE =A

=B

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

We offer another EF mantle solution (452.0845) which is compatible with our MF, F and EF concaves. A minor step after the last big step has been machined to allow for up to 15 mm larger feed sizes compared to the standard EF mantle (452.0844). Available as 452.0845-001 (M1), 452.0845-002 (M2) and 452.0845-005 (M9).

Crushing Chamber Application Guide

119


CH (H-TYPE) CONE GUIDE

CH870i (CH870, H7800) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85***

FLEXIFEED MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 41 EC Top Grip

47

198

52 57 62 68 32 37 41

C

47

162

52 57 62 68 32 37 41

MC

47

134

52 57 62 68

MANTLE

ALLOY MIX

FF

CONCAVE EC TOP GRIP

FILLER RING

C

EC TOP GRIP

C/MC

BG00239981-01

M1

BG00239713-01*

452.2255-001**

452.2253-001**

452.0891-901

452.2269-901

BG00239981-02

M2

BG00239713-02*

452.2255-002**

452.2253-002**

452.0891-901

452.2269-901

BG00239981-05

M9

BG00239713-05*

452.2255-005**

452.2253-005**

452.0891-901

452.2269-901

MANTLE TYPE = FF * Filler ring 452.0891-901 is needed between the concave and the top shell ** Filler ring 452.2269-901 is needed between the concave and the top shell *** F85 only applies when using Flexifeed (FF) mantle

120

MC

Crushing Chamber Application Guide


OVERSIZE BREAKER - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Oversize Breaker (OB) mantle is engineered for tertiary or final crushing applications. It has a varying feed opening that increases the allowable top size in finer crushing chambers, and helps to prevent bridging from oversized process material.

CONCAVES

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

FLEXIFEED MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 41 47 MF

86

122

52 57 62 68 74 80 32 37 41 47

F

79

1 112 12

52 57 62 68 74 80 32 37 41 47

EF

70

100

52 57 62 68 74 80

MANTLE

ALLOY MIX

OB

CONCAVE

FILLER RING

MF

F

EF

452.4900-001

M1

452.0842-001*

452.0841-001*

452.0840-001*

452.0898-901

452.4900-005

M9

452.0842-002*

452.0841-002*

452.0840-002*

452.0898-901

MANTLE TYPE = OB * Filler ring is needed between the concave and the top shell

Crushing Chamber Application Guide

121


CH (H-TYPE) CONE GUIDE

HIGH REDUCTION - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our High Reduction concave has a unique shelf design that increases the crushing chamber pressure in finer applications. This patented feature has proven to offer up to 10% more final product compared to conventional designs, and offers up to 19% less recirculating load, creating a more efficient crushing circuit.

CONCAVE HR

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 8

10

13

16

19

22

25

29

32

38

44

51

57

64

70

32 37 42 47 75

94

52 57 62 68 74 80

CONCAVE

ALLOY MIX

HR

STANDARD MANTLE B*

EF

OB

BG00401157-01

M1

452.0837-001

BG00692006-01

n/c

n/c

452.0898-901

BG00401157-02

M2

452.0837-002

BG00692006-02

n/c

n/c

452.0898-901

BG00401157-05

M9

452.0837-005

BG00692006-05

n/c

n/c

452.0898-901

MANTLE TYPE =A

=B

* This version of our B-mantle has a shorter metallic contact and is to be used with our HR-concave. ** Filler ring is needed between the concave and the top shell n/c = not compatible

122

FILLER RING**

A

Crushing Chamber Application Guide


Crushing Chamber Application Guide

123


CH (H-TYPE) CONE GUIDE

CH890i (CH890, CH880, H8800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS

CONCAVE EC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 294

428

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

EC

STANDARD MANTLE A

FILLER RING**

B

EF

HC

442.9336-01

M1

442.9314-01

442.9339-01

n/c

n/c

-

442.9336-005

M9*

442.9314-005

442.9339-005

n/c

n/c

-

CONCAVE C

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 262

382

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

C

124

STANDARD MANTLE

FILLER RING**

A

B

EF

HC

442.9398-01

M1

442.9314-01

442.9339-01

n/c

n/c

-

442.9398-005

M9*

442.9314-005

442.9339-005

n/c

n/c

-

Crushing Chamber Application Guide


CONCAVE MC

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 208 239 (HC)

44

302 348 (HC)

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

MC

A

B

EF

FILLER RING** HC

442.9471-01

M1

442.9314-01

442.9339-01

n/c

442.9758-01

442.9520-00

442.9471-005

M9*

442.9314-005

442.9339-005

n/c

442.9758-005

442.9520-00

CONCAVE M

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 175 206 (HC)

44

219 257 (HC)

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

M

A

B

EF

FILLER RING** HC

442.9337-01

M1

442.9314-01

442.9339-01

n/c

442.9758-01

442.9338-00

442.9337-005

M9*

442.9314-005

442.9339-005

n/c

442.9758-005

442.9338-00

MANTLE TYPE =A

= Heavy Choke (HC)

= B or HC

=B

= A or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

Crushing Chamber Application Guide

125


CH (H-TYPE) CONE GUIDE

CONCAVE MF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 119 145 (HC)

44

149 182 (HC)

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

MF

A

B

EF

FILLER RING** HC

442.9312-01

M1

442.9314-01

442.9339-01

n/c

442.9758-01

442.9332-00

442.9312-005

M9*

442.9314-005

442.9339-005

n/c

442.9758-005

442.9332-00

CONCAVE F

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 111

139

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

F

STANDARD MANTLE B

EF

HC

442.9471-01

M1

n/c

n/c

452.0264-001

n/c

442.9520-00

442.9471-005

M9*

n/c

n/c

452.0264-005

n/c

442.9520-00

MANTLE TYPE =A

= Heavy Choke (HC)

= B or HC

=B

= A or HC

= EF

* Premium product ** Filler ring is used between the concave and the top shell n/c = not compatible

126

FILLER RING**

A

Crushing Chamber Application Guide


CH890i (CH890, CH880, H8800) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

FLEXIFEED - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Flexifeed (FF) mantle is engineered for your secondary crushing applications, and offers up to a 20% longer lifetime compared to a correctly configured standard chamber. It has a varying feed opening that is ideal if the crusher feed is not calibrated.

CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

F85**

MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 EC

242

48 52 56 60 64 68 70 24 28 32 36 40 44

C

216

48 52 56 60 64 68 70

MANTLE

ALLOY MIX

FF

CONCAVE EC

C

FILLER RING MC

BG00282784-01

M1

442.9336-01

442.9398-01

442.9471-01*

442.9520-00

BG00282784-05

M9

442.9336-005

442.9398-005

442.9471-005*

442.9520-00

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

Crushing Chamber Application Guide

127


CONCAVES

MAX. FEED SIZE (mm)

ECC. THROW (mm)

MANTLE CSS (mm)

F85**

13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 MC

171

48 52 56 60 64 68 70

MANTLE

ALLOY MIX

FF

CONCAVE EC

FILLER RING

C

MC

BG00282784-01

M1

442.9336-01

442.9398-01

442.9471-01*

442.9520-00

BG00282784-05

M9

442.9336-005

442.9398-005

442.9471-005*

442.9520-00

MANTLE TYPE = FF * Filler ring is needed between the concave and the top shell ** F85 only applies when using Flexifeed (FF) mantle

OVERSIZE BREAKER - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Oversize Breaker (OB) mantle is engineered for tertiary or final crushing applications. It has a varying feed opening that increases the allowable top size in finer crushing chambers, and helps to prevent bridging from oversized process material.

CONCAVE

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

13

16

19

22

25

29

32

38

44

51

24 28 32 36 40 44 F

111

158

48 52 56 60 64 68 70

MANTLE

ALLOY MIX

CONCAVE

452.4051-001

M1

442.9471-01*

442.9520-00

452.4051-005

M9

442.9471-005*

442.9520-00

OB

F

MANTLE TYPE = OB * Filler ring is needed between the concave and the top shell

128

FILLER RING

Crushing Chamber Application Guide

57

64

70


Crushing Chamber Application Guide

129


CH (H-TYPE) CONE GUIDE

CH895i (CH895, CH880, H8800) STANDARD CRUSHING CHAMBER SOLUTIONS CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS CONCAVE EFX

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

57

64

70

24 28 32 36 40 44 89

112

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

452.1067-001

M1

452.0264-001

-

452.1067-005

M9*

452.0264-005

-

EFX

CONCAVE EF

FILLER RING**

EF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

24 28 32 36 40 44 77

97

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

EF

130

STANDARD MANTLE

FILLER RING**

EF

452.0263-001

M1

452.0264-001

-

452.0263-005

M9*

452.0264-005

-

Crushing Chamber Application Guide


CONCAVE EEF

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

MANTLE CSS (mm)

F100

10

13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 68

86

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

EEF

FILLER RING**

EF

452.0579-001

M1

452.0264-001

-

452.0579-005

M9*

452.0264-005

-

MANTLE TYPE = EF * Premium product ** Filler ring is used between the concave and the top shell

Crushing Chamber Application Guide

131


CH (H-TYPE) CONE GUIDE

CH895i (CH895, CH880, H8800) PREMIUM CRUSHING CHAMBER SOLUTIONS Our unique profiles and wear-resistant alloys help to achieve optimal crushing performance, ensuring more uptime and lower operating costs.

OVERSIZE BREAKER - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our Oversize Breaker (OB) mantle is engineered for tertiary or final crushing applications. It has a varying feed opening that increases the allowable top size in finer crushing chambers, and helps to prevent bridging from oversized process material.

CONCAVES

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

10 24 28 32 36 40 44

EFX

89

127

48 52 56 60 64 68 70 24 28 32 36 40 44

EF

77

110

48 52 56 60 64 68 70

132

Crushing Chamber Application Guide

FLEXIFEED MANTLE CSS (mm) 13

16

19

22

25

29

32

38

44

51

57

64

70


CONCAVES

MAX. FEED SIZE (mm) F90

ECC. THROW (mm)

F100

FLEXIFEED MANTLE CSS (mm) 10

13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44 48 EEF

68

97

52 56 60 64 68 70 74 80

MANTLE

ALLOY MIX

OB

CONCAVE

FILLER RING

EFX

EF

EEF

452.4051-001

M1

452.1067-001

452.0263-001

452.0579-001

-

452.4051-005

M9

452.1067-005

452.0263-005

452.0579-005

-

MANTLE TYPE = OB

Crushing Chamber Application Guide

133


HIGH REDUCTION - CONCAVE, ECCENTRIC THROW AND MANTLE COMBINATIONS Our High Reduction concave has a unique shelf design that increases the crushing chamber pressure in finer applications. This patented feature has proven to offer up to 10% more final product compared to conventional designs, and offers up to 19% less recirculating load, creating a more efficient crushing circuit.

CONCAVE MAX. FEED SIZE ECC. THROW HR (mm) (mm) F90

F100

MANTLE CSS (mm) 6

8

10

13

16

19

22

25

29

32

38

44

51

57

64

70

24 28 32 36 40 44

85 106 71 (HC) 89 (HC)

48 52 56 60 64 68 70

CONCAVE

ALLOY MIX

STANDARD MANTLE

HR

A

B

EF

OB

BG00284338-01

M1

442.9314-01

442.9758-01

442.9758-01

n/c

n/c

-

BG00284338-05

M9

442.9314-005

442.9758-005

442.9758-005

n/c

n/c

-

MANTLE TYPE

134

FILLER RING

HC

=A

= Heavy Choke (HC)

=B

= A or HC

Crushing Chamber Application Guide

= B or HC


Crushing Chamber Application Guide

135


136

Crushing Chamber Application Guide


APPLICATION AND TROUBLESHOOTING

IMPORTANCE OF CRUSHING CHAMBER SELECTION – CONE CRUSHER

138

COMMON FEED ARRANGEMENT PROBLEMS

140

OPTIMAL FEED ARRANGEMENT

142

WHEN TO CHANGE LINERS – CONE CRUSHERS

144

UNWANTED WEAR PATTERNS – CONE CRUSHERS

147

UNWANTED WEAR PATTERNS – JAW CRUSHERS

150

Crushing Crushing Chamber Chamber Application Application Guide Guide

137 137


APPLICATION AND TROUBLESHOOTING

IMPORTANCE OF CRUSHING CHAMBER SELECTION – CONE CRUSHERS WHAT AFFECTS CRUSHER PERFORMANCE? In terms of your desired product (whether it is a P80 or a target fraction), crushing chamber performance is primarily affected by your crushing chamber selection – or the fit between the concave and mantle, coupled with the eccentric throw setting. The wrong fit and settings can mean up to a 40% loss in your reduction ratio. Poor feeding conditions can also lead to a loss of around 30%, since the Hydroset pressure cannot be maintained within its optimal setting. As a result, fluctuations in pressure peaks lead to a coarser product. In finer crushing applications, packing caused by poor feeding conditions also affects the reduction ratio negatively as the pressure sectors – or the amplitude between the average peak and average pressure – are high in one area of the chamber. This leads to a lowering of the main shaft (and hence Hydroset pressure), giving a coarser product. Finally, the wrong mantle selection can lead to about a 20% loss in your reduction ratio. In some limited application areas, a poor chamber profile or design leads to a 20% loss as well. Surprisingly, the wrong alloy selection has no effect when it comes to reduction ratio.

COMMON PROBLEMS AFFECTING PRODUCTIVITY 100 90

Lost reduction rate (%)

80 70 60 50 40 30 20 10 0 Wrong crushing chamber

138

Crushing Chamber Application Guide

Poor feeding conditions

Wrong mantle

Correct chamber but poor profile

Wrong alloy


WHAT AFFECTS LINER LIFE? When it comes to liner life, cone crushing chamber performance can be impacted by a number of factors – the most common of which is poor feeding conditions. A poor feed can reduce the lifetime of your liners by up to 70% when compared with a properly fed crusher. Another major factor is crushing chamber selection – again the fit between the concave and mantle, coupled with the eccentric throw setting. Liner life can be decreased by as much as 50% when the fit or settings aren’t right. Additionally, the wrong mantle selection can mean a decrease of up to 40% in liner life, and an incorrect alloy selection can decrease it by about 20%. COMMON PROBLEMS AFFECTING LINER LIFE 100 90

Effect on chamber lifetime (%)

80 70 60 50 40 30 20 10 0 Poor feeding conditions

Wrong crushing chamber

Wrong mantle

Wrong alloy

Correct chamber but poor profile

Feed arrangements usually account for 7 out of 10 liner wear issues. Checking the feed to the crusher is always a good starting point. % figures are not mutually exclusive.

Incorrect feeding arrangement are a common problem in crushing applications, and when fixed have huge potential to improve the operation of your crusher. In fact, all other crushing chamber optimization efforts will be sub-optimal – and may not even work – if feeding is poor. Infrastructure – like height restrictions – can be a limiting factor when trying to correct feed arrangement problems. Issues with the feed arrangements can be broken down into five common groupings: • Segregation is when coarse and fine particles of the crusher feed enter different parts of the chamber • Misalignment is when material is fed to one part of the chamber • Trickle feeding is when the amount of material entering the chamber is not sufficient to fill it • Bridging is when the feed material gets stuck above the chamber opening and does not allow material to enter the crushing chamber • Spider cap buildup leads to an unevenly filled crushing chamber as one side is not choke fed

Crushing Chamber Application Guide

139


APPLICATION AND TROUBLESHOOTING

COMMON FEED ARRANGEMENT PROBLEMS SEGREGATION Segregation is when coarse and fine particles of the crusher feed enter different parts of the chamber. Typically, coarse material goes to the top and the fines accumulate in the bottom of the feed material. There are several common causes of segregation. Material can segregate as soon as it hits a horizontal surface; vibrations can increase segregation further; and two conveyors can feed into the crusher at the same time. Segregation can be fixed when the correct feeding device is used. This can include a feed distributor, splitter, hit plate, tube chute, centering chute or a feeder box. A Sandvik Rotating Feed Distributor (RFD) can also be installed above the hopper to evenly distribute the feed material, ensuring optimal crushing chamber performance. Horizontal segregation is harder to correct with simple measures. Fixes can include making corrections earlier in the transportation system or installing a Sandvik RFD. MISALIGNMENT Misalignment is when the material is fed to one part of the crushing chamber inlet. This can be caused by feeding with the belt conveyor or because of the poor alignment of the vibrating feeder. Misalignment can be fixed by correcting the feeding arrangement using a splitter, feed box or hit plate. A splitter – which spreads the material in the feed hopper – should only be used for coarse- and fine-crushing applications. A Sandvik RFD can also be installed above the hopper. TRICKLE FEEDING (A “STARVED” CRUSHER) Trickle feeding is when the amount of material entering the chamber is not sufficient to fill it. It can be caused by problems with the control system, faulty equipment (like feeders and sensors), an incorrectly placed level monitor or simply lack of know-how. In order to fix trickle feeding, the sources of this faulty feed arrangement need to be fully understood, and whatever is not working properly or designed correctly needs to be fixed – such as increasing the feed amount or installing a bin ahead of the crusher. BRIDGING Bridging is when the feed material gets stuck in the hopper and does not enter the crushing chamber. It can be caused by a coarse feed with a single size, flaky or elongated material, and mechanical obstructions in the feed hopper and crusher. Fixing a bridging issue starts with changing the feed by adjusting the previous crusher’s CSS setting, the feeding arrangement or removing the edges that stop the material from moving through the chamber. Another solution could be to change to one of our “multifeed” mantles. In secondary applications, we offer the Flexifeed mantle, while our Oversize Breaker is intended for fine-crushing applications. Both mantles increase the allowable top size and help prevent bridging from oversized feed material. SPIDER CAP BUILDUP Spider cap buildup is caused when feed material with a high amount of fines and moisture content leads to a conical form shape on the top of the spider cap. A misaligned feed chute contributes to the buildup which leads to an unevenly filled crushing chamber as one side is not choke fed. Using only one level sensor may give a “false” reading depending on which side of the chamber it is measuring. Spider cap buildup can be detected by using two level sensors, leading to a more correct feeding level of the entire chamber. Once detected, the spider cap needs to be dislodged manually. A visual check from the hopper inspection hatch should be performed daily if two level sensors are not installed and if the site has a history of buildup problems. 140

Crushing Chamber Application Guide


SEGREGATION ON BELT

SEGREGATION INSIDE HOPPER

MISALIGNMENT

TRICKLE FEEDING

BRIDGING

SPIDER CAP BUILDUP

Crushing Chamber Application Guide

141


APPLICATION AND TROUBLESHOOTING

OPTIMAL FEED ARRANGEMENT CHOKE FEEDING The optimal feed arrangement for a Sandvik cone crusher is to choke feed the crusher with a non-segregated feed. Choke feeding and good feed distribution lead to optimal crushing chamber performance, helping the crusher run more smoothly by lowering both power and pressure peaks. In choke feeding, you regulate the feed so there is a buildup of evenly distributed material in the feed hopper. The recommended level will depend on the crushing stage, crusher model (CS or CH), crushing chamber (coarse vs. fine), as well as the risk of bridging. At a minimum, the head nut should always be covered by the feed material, ensuring the crushing chamber is choke fed.

We recommend electrically connecting and interlocking the feed arrangement, so it cannot be started before the crusher and the discharge system are running. Sandvik offers a feed-level sensor that can monitor the level of material in the feed hopper, ensuring the correct level. It too should be interlocked with the feed arrangement to prevent overfilling. The use of a feeder with a variable speed drive – coupled with the feed-level sensor – will help you maintain a constant material level in the hopper. A pre-crusher surge bin with a low-level monitor connected to the control system can also ensure proper feeding.

LEVEL WITH SPIDER CAP

FINE CRUSHING JUST BELOW SPIDER ARMS COARSE CRUSHING

JUST ABOVE THE HEAD NUT

Adhering to the recommended levels in the feed hopper when choke feeding help ensure optimal performance, even liner wear and lowering both power and pressure peaks.

142

Crushing Chamber Application Guide


SPIDER ARM PLACEMENT In order to ensure optimal crushing chamber performance – including maximum liner life – the feed material should not be segregated before it is fed into the crushing chamber. This can be accomplished with the use of a feed distribution device, such as a static three-way distributor, a splitter or a rotating feed distributor. In the absence of a distributor device, a feed box can be used to try to optimize the feed arrangement as much as possible. If a splitter or three-way distributor device is installed above the cone crusher, the spider arms will sit at right angles (90º) to the feeder or conveyor (image on left). If a splitter is not used, the spider arms must be aligned with the feeder or conveyor (image on right). In the end, solving a bad feed arrangement usually comes down to installing a feed alignment device – like a Sandvik Rotating Feed Distributor (RFD). Height restrictions can be an issue but if they’re not, the rotating feed distributor is an investment that repays itself quickly as it avoids the premature exchange of your liner set. It might also be cost-effective in the long run to adjust your infrastructure in order to correct your feed arrangement problems.

Crusher with a distribution device (e.g. splitter)

Crusher without a feed distribution device

Crushing Chamber Application Guide

143


APPLICATION AND TROUBLESHOOTING

WHEN TO CHANGE LINERS – CONE CRUSHERS A visual inspection of the crushing chamber is the recommended way to decide when the liners need to be changed. As part of your routine inspection protocol, the crushing chamber should be checked daily to reveal possible cracks in the concave or mantle, as well as abnormal wear patterns. Looking into the crushing chamber through the inspection hatches on the feed hopper is a simple way to check the upper part of the chamber. This inspection can reveal possible chamber blocking and bridging issues, not to mention non-crushable items that might have entered the feed hopper. Any such items should be removed before operation, as they will affect the crusher’s performance. It is advisable to spend a few minutes examining the concave and mantle through the bottom shell inspection hatches. This will reveal possible wear abnormalities that might affect your crushing chamber’s performance or lead to crusher downtime. If any of the liners are cracked or show abnormal wear patterns, they should be changed immediately. An investigation into the root cause should be done to take proper corrective measures. THE A-DIMENSION The crushing chamber is usually worn out when the minimum allowable A-dimension is reached (as per the table below). However, the chamber could be worn out before the minimum A-dimension is reached depending on your CSS and eccentric throw settings. A visual inspection is always needed to confirm when the liners need to be changed, as the A-dimension cannot detect cracks or uneven wear patterns that can affect productivity.

MIN. A-DIMENSION

CH MODELS

MINIMUM ALLOWABLE A-DIMENSION (MM)

CH420, CH430, CH440, CH540, CH550, CH660, CH870i

15

CH880 (discontinued model)

25

CH895i

35

CH860i, CH865i, CH890i

40

CS MODELS

144

CS420, CS430, CS440

15

CS550

17

CS660

20

Crushing Chamber Application Guide


The ASRi system is a great tool to track the A-dimension. It will show how worn your liners might be, and it will give you a warning when the A-dimension becomes too small. If your crusher is not equipped with the ASRi, then the A-dimension needs to be measured manually. When the minimum A-dimension is reached, it’s time for a liner change. However, the chamber could be worn out before the minimum A-dimension is reached depending on your CSS and eccentric throw settings. A visual inspection of the crushing chamber is the recommended way to decide when your liners need to be changed. You should never exceed the minimum A-dimension even if there appears to be more wear life in your crushing chamber. Raising the main shaft beyond the minimum A-dimension could cause damage to the spider hub and the head nut.

GOOD WEAR Sandvik crushing chambers are designed to maintain an even shape of the liners to extend your operational life and increase your output. As wear occurs, the upward movement of the mantle maintains both the shape and volume of the chamber, and the size of the feed opening during the entire service life of the liners. This means that wear is evenly distributed over the surface of each liner, so the production rate of the crusher is never reduced as the liners wear.

New liners

Worn liners

You can get a good confirmation on your feed arrangement setup and your crushing chamber selection by examining a worn mantle and concave. A properly worn mantle and concave indicate that you don’t have any feed issues and your crushing chamber selection is correct. Both the mantle and concave should be changed at the same time to ensure optimal crushing chamber performance. However, with our CS model, you may need to change the mantle and/or the lower concave ring due to localized wear. A visual inspection of the crushing chamber is the only way to decide whether to change the mantle, the lower concave or both – and when to change the complete liner set. Crushing Chamber Application Guide

145


146

Crushing Chamber Application Guide


UNWANTED WEAR PATTERNS – CONE CRUSHERS Uneven crushing chamber wear is a big waste of money. It can lead to higher OPEX and cost per ton, and it affects the technical performance of your crushing chamber by reducing the amount of final product. Segregation inside the crusher in particular is also much more difficult to observe, causing premature and unwanted chamber wear. Uneven wear patterns can have two underlying causes – bad feed arrangements or an incorrect crushing chamber selection. INCORRECT FEEDING Incorrect feeding is caused by bad feed arrangements. A circulating load from a closed circuit also contributes to incorrect feeding since the fresh and recirculated material are seldom mixed properly before entering the crusher. Uneven wear around the concave circumference is a typical sign of incorrect feeding caused by a misaligned feed or feed segregation. As a result, the ASRi metal-to-metal calibration is incorrect, your product becomes coarser, and you get uneven operation with power and pressure peaks – all of which lead to poor crushing chamber utilization and a shorter lifetime. To fix this issue, you should adjust the feeder and install a feed distributor, like the Sandvik RFD.

BAD FEED

GOOD FEED

The Hydroset pressure sectors – or the amplitude between the average peak and average pressure – are tracked and recorded within our automation system. Large variations are a sign of feed problems. In a crusher that is choke fed with a non-segregated feed, these variations are much narrower leading to better crushing chamber utilization and longer service life of the liners.

Crushing Chamber Application Guide

147


APPLICATION AND TROUBLESHOOTING

INCORRECT CRUSHING CHAMBER SELECTION This is generally caused by incorrect selection of the concave, mantle and eccentric throw, leading to uneven wear and a lower lifetime for your liners. Determining or estimating your particle size distribution (maximum feed size) will help to fix the issue. You should also reevaluate your concave, mantle and throw combination. Just keep in mind that when you change the concave, your crusher’s capacity will also change.

There are four symptoms that indicate incorrect crushing chamber selection:

NOSE FORMATION The profile of the mantle looks like a nose. This happens when an A-mantle (high wear zone) is paired with the wrong eccentric throw and CSS. This will drastically reduce your capacity and cause high-pressure peaks. It can be corrected by changing to a B-mantle, which should be used with a large CSS and large eccentric throw. You can also decrease the CSS.

CUPPING This happens when a B-mantle (low wear zone) is paired with a small CSS or when too fine an end product is being produced in a coarse chamber in a closed circuit. This can reduce wear life by up to 20% and increase the end product size by 20%, even if the CSS appears to be small. Changing to an A-mantle, increasing the CSS or trying a finer liner can fix the issue.

148

Crushing Chamber Application Guide


LOCALIZED WEAR IN THE MIDDLE OR LOWER PART OF THE CHAMBER (CH MODEL) This is caused by a feed fraction that’s too short in the middle of the chamber, or too many fines in the feed at the bottom of the chamber. It can also happen if the chamber is trickle fed. This issue reduces wear life and your capacity, but it can be fixed by choke feeding the crusher, installing a minimum-level sensor in the surge bin, trying a smaller eccentric throw, selecting a finer chamber if the feed size allows, or using a Sandvik Flexifeed mantle. LOCALIZED WEAR IN THE UPPER PART OF THE CHAMBER (CH MODEL) This is caused by a coarse or short feed. It leads to premature liner changes, heavy wear at the top, a poor nip angle that decreases capacity, or a nip angle that increases the slippage and generates even more wear. It can be fixed by choosing a coarser chamber or feed mix. LOCALIZED WEAR IN THE MIDDLE OR LOWER PART OF THE CHAMBER (CS MODEL) When there is a high percentage of fines in the feed of an S-type crusher, crushing is uneven, leading to less wear in the top part of the mantle. This can cause premature liner changes, such as cracking, as well as decreased flow, leading to lower capacity. To avoid cracking and poor capacity, try using a finer chamber or remove fines by scalping.

CRACKING This is caused by either an incorrect alloy selection or poor liner seat. Either problem leads to a shorter lifetime of the crushing chamber. In very limited cases, the casting itself is the source of the defect. We recommend using our Sandvik M1 alloy when you’re crushing a material that’s too hard compared to the alloy’s impact resistance or if there is a high frequency of tramp objects entering the crushing chamber. With its high resistance to impact, it will increase shock resistance and does not crack easily. You can also install our electric dump valve system to protect your crusher against tramp objects, and reduce unwanted pressure peaks by up to 90%. When there is a fitting gap between the metallic contact surface and the liner, the material can move and usually cracks as a result. To correct this issue, the metallic surface must be restored by grinding and polishing. Crushing Chamber Application Guide

149


APPLICATION AND TROUBLESHOOTING

UNWANTED WEAR PATTERNS – JAW CRUSHERS Uneven crushing chamber wear is a big waste of money. It can lead to higher OPEX and cost per ton, and it affects the technical performance of your crusher by reducing the amount of final product. Uneven wear patterns can have several underlying causes – bad feed arrangements, turning plates too late, incorrect jaw plate selection or incorrect crusher setup. You’ll know if you have wear problems if you see manganese growth, localized wear, a ski slope shape, cupping, nose formation or “jumping” rocks. MANGANESE GROWTH As manganese spreads on the jaw plates, the jaw plates grow. This produces an increased force on the fastening details. So to minimize wear, the jaw plates should be turned more often. If the jaw plate is flexing – and most of the crushing is done in the same crushing zone – then it’s best to change the teeth pattern and use shim plates. Sandvik machines the back of the jaw plates to offer better support on the protection shim plate and prevent flexing. WORN OUT AT ONE END This happens when the jaw plates are not turned, resulting in worn teeth and a loss of grooves for the fines to pass through. This results in more slippage, less crushing, more compaction and reduced capacity. It also means using a higher CSS to avoid overload. The solution is to turn the jaw plates more frequently. SKI SLOPE WEAR This happens when the jaw plates are worn far down in the crushing zones, and when they are turned after the teeth are already gone. Overall it results in a good wear pattern, but one in which there is more material to utilize in the center than on the ends. In order to remedy this, you should install a shim plate to spread out crushing more evenly in the chamber. NOSE FORMATION This happens when the setting is too small (under limit) or there is a poor nip angle. It means that crushing is only done at the bottom of the chamber, resulting in reduced wear life (nose formation), reduced capacity and high mechanical stress on the crusher. To fix it, you should open up the setting and decrease the nip angle. You can also use a shim plate to move the crushing zone up. CUPPING This happens when the feed is too fine and the feed level is too low, resulting in short liner life and reduced capacity. In order to fix the issue, you shouldn’t trickle feed the crusher. Instead, use a feed hopper and run it in on/off mode, and use a backing plate to move the crushing zone up. “JUMPING” ROCKS This means the rock is not getting pinched, but is “jumping” in the crusher without getting crushed. This happens when there is a poor nip angle, grip pattern or no intermediate rock – and results in reduced capacity and excess wear in the middle of the jaw plate. To fix the issue, you should mix the feed, change to a coarse corrugated pattern, install a shim plate or increase the CSS.

150

Crushing Chamber Application Guide


EXAMPLE OF MANGANESE GROWTH

EXAMPLE OF NOSE FORMATION

EXAMPLE OF “JUMPING” ROCKS

Crushing Chamber Application Guide

151


152

Crushing Chamber Application Guide


SAMPLING METHODOLOGY

SAMPLING IN COMMINUTION PLANT PRACTICES

154

TAKING A BELT-CUT: A FIVE-STEP PROCESS

155

SAMPLING PROTOCOL

159

Crushing Crushing Chamber Chamber Application Application Guide Guide

153 153


SAMPLING METHODOLOGY

SAMPLING IN COMMINUTION PLANT PRACTICES Sampling is critical to your plant’s quality control – a practice that is just as important as testing. The first step is taking a sample that can provide a complete picture of your product’s properties and quality, such as gradation, size, shape, density and more. PRODUCT

FEED

100 90

Amount passing through (%)

80 70 60 50 40 30 20 10 0 0.01

0.1

1 Square hole (mm)

10

100

The size distribution of the raw material is called the particle size distribution, or PSD for short. It is commonly referred to as the gradation. F80 is the size for 80% of the feed material passing. P80 is the size for 80% of the product material passing.

Remove a conveniently sized sample for testing that is representative of the much larger whole. Unfortunately, sampling is often done incorrectly because the sample is not representative. In practice, the dimensions of the largest pieces in the feed determine the sample amount needed. In crushing plants, stockpile and conveyor-belt cuts are the conventional sampling methods. Conveyor-belt cuts accurately determine gradation in aggregate materials. The traditional way of obtaining a belt-cut sample requires that you stop production. In this process, a sampling frame that matches the curvature of the conveyor belt manually cuts and separates a cross-section of the material. Three to five cuts are then taken, and the material is brushed into a bucket for testing. For each cut, up to five meters of the conveyor belt is typically sampled. However, this sampling method relies on the employee taking a complete sample, including fines. This can affect your production rates, and create safety concerns. Another method is cross-belt sampling, which uses the automated cross-belt sampler on the conveyor. With cross-belt samplers, there is no downtime and it eliminates safety concerns.

154

Crushing Chamber Application Guide


TAKING A BELT-CUT: A FIVE-STEP PROCESS In order to evaluate your crusher’s performance, field samples are needed. Sampling is not only critical to your plant’s quality control; it is also used to calibrate the Sandvik simulation software model. The results adapt the model to local operating conditions and rock material, which is essential for achieving prediction accuracy in your operations.

Crushing Chamber Application Guide

155


SAMPLING METHODOLOGY

STEP 1: PLANNING You can start by understanding the objective of the sampling. Perhaps you have a new crushing chamber, a changed throw, performance changes due to wear, a performance guarantee or you want to optimize your process. Then consider the repeatability of the test. Do you have raw material changes, crushing chamber wear, process changes or a change in the position of your crusher? Then evaluate your crusher according to your feed and final product, and evaluate all sampling points of interest in your plant. Finally, evaluate your plant capacity. With all of this information, you can then go through the flow sheet and layout to find a sampling location, and identify potential sampling problems – for example, if the crusher discharge belt is shared with other equipment. DETERMINE THE SAMPLE SIZE One of the most vital steps is determining the size of your sample. It is important to use common sense when taking samples. For example, a 100 kg sample might not be feasible to analyze if it is a fine product, just as a 20 kg sample might not be representative for a coarse product. There are different country/regional norms describing minimum required sample sizes. If you’re using the European norm EN932-1, you would calculate the minimum required sample size this way:

M=6x

D x ρb

M = D = ρb =

IS THE MASS OF THE SAMPLE IN KILOGRAMS IS THE MAXIMUM GRAIN SIZE IN MILLIMETERS IS THE LOOSE BULK DENSITY IN MEGAGRAMS PER CUBIC METER, AS SPECIFIED IN PREN 1097-3

You can then use the following equation to calculate the length of belt to sample:

L=

3.6 x V x Ms C

V = CONVEYOR SPEED (M/S) MS = SAMPLE SIZE (KG) C = CRUSHER CAPACITY (MTPH)

In most cases, a 1m belt cut will give you a large enough sample. Of course, at a minimum there has to be enough material there to sample. Image analysis is a process that can be used when the particle size is too large for a normal sieve analysis.

STEP 2: INSPECTION Plant inspection starts with a walk-through of the process. It helps you become familiar with the process control system, and make sure the process is in accordance with the flow sheet when it comes to material flow, crusher settings (CSS, throw, crushing chamber), feed bins and intermediate storage, and screen separations. Then find a location where the belt-cut sample can be collected. It should be far enough away from the crusher so the material on the belt is representative of the choke-fed crusher. Walkways, encapsulations and the angle of the conveyor can cause restrictions at sampling points. Have a detailed look at the crusher, and check for these characteristics: • Choke feeding, but segregation and large lump size • Under-feeding • Start/stop operation • Large pressure variations • Wear history • Uneven crushing chamber wear • Unwanted material in the hopper like wood, plastic, etc. • Welded steel plate in the hopper Finally, the crusher’s CSS needs to be calibrated to ensure you know what you are measuring. If possible, calibrate your crusher with lead at four points – or do it automatically with ASRi. 156

Crushing Chamber Application Guide


STEP 3: COLLECTION Sandvik’s objective is always zero harm to people, the environment we work in, our customers and our suppliers. It is important before beginning to ensure that all relevant safety measures are in place, and that all necessary preparations have been made so the sampling process is carried out safely. GET CRUSHER RUNNING AT A STEADY STATE First, ensure that you have stable operating conditions. ASRi is a great tool for monitoring this, and there are several methods you can use to increase operating stability. These include adjusting the CSS until stability is reached, reviewing your feeding conditions, and reviewing the process once more. If you don’t have ASRi, ensure the crusher is calibrated. Then operate your crusher at a steady state for at least a few minutes. Before stopping the belt, make sure that no material other than the crusher discharge is on the belt, the crusher is choke fed, and the power and pressure are constant. A steady state is very important with closed circuits. You need to know how long it takes for the return material to mix with the fresh feed. For example, capacity with a coarse, fresh feed could be 130 mtph, but it reaches 210 mtph when the material is returned and a steady state is reached. Premature sampling based on a 130 mtph production will not give you a representative field sample. TAKING THE BELT-CUT SAMPLE It is important to collect enough material so the sample is statistically significant. Measure a given distance on the conveyor belt and then collect all of the material within this determined length. After stopping the belt, collect a belt cut that is as accurate as possible. Try to prevent the material from migrating in or out of the sample on inclined belts or when the material bed is thick. A sampling frame can help keep belt-cut lengths constant when comparing results. Metal sheets or something similar can help keep the material in place. Remember that the accuracy of capacity measurement is proportional to the length of the belt cut. On a 1 m belt cut, +/-5 cm corresponds to +/- 5% capacity error. But on a 0.5 m belt cut, 5cm corresponds to +/- 10% capacity error. Then store the sample in a plastic bag or bucket, and ensure it is protected from rain and wind. Label the sample with the relevant information. For example: Product crusher No. 2, CSS 22 mm, 3 bags. Then you can send the sample to a lab for analysis.

Crushing Chamber Application Guide

157


STEP 4: ANALYSIS Your sample is often split down to a smaller size to fit a lab sieve; a riffle box can be used to reduce the sample size. This minimum test portion is needed because it reduces the risk of overloading the lab sieves that could bias the result. Just beware of the slot opening as oversized particles are sometimes thrown away. If the Bond crushability Work Index is unknown a sample can be sent to Sandvik´s laboratory in Svedala, Sweden for testing. To determine the correct stone size for the Work Index Test, pick 25-30 stones in a size that will pass through a 75x75 mm opening and be retained by a 55x55 mm opening. The rocks should be fairly cubical with a length-to-thickness ratio of less than three. To evaluate the sample process and the performance of a cone crusher, the following information is needed: FEED

CRUSHER

PRODUCT

Specific gravity

Crusher type

Capacity

Work index

Crushing chamber

Size distribution

Moisture content

CSS

(Shape)

Size distribution

Throw Power Pressure A-dimension

STEP 5: EVALUATION The size distribution curve can be used to evaluate the result and indicate a correct sample. Typically 70-95% of a correct sample will be smaller than the CSS. Indicators of an incorrect sample are dents in the size distribution curve, no fines or fewer fines than in the feed, and a top size that is much larger than the CSS.

SAMPLING PROTOCOL The sampling protocol should be used when cone crusher performance is tested. If the protocol is followed and filled in completely, you will have all of the information necessary to evaluate the test results. The protocol also helps ensure the operating conditions are representative when the sample is taken – and that the right conclusions can be drawn from the test. 158

Crushing Chamber Application Guide


SAMPLING PROTOCOL CONE CRUSHER PLANT:______________________________________________________________________________ DATE:___________________________ SAMPLED BY:_______________________________________ CRUSHER CALIBRATED

OTHER INFORMATION:

NO BRIDGING IN HOPPER NO BLINDING OF SCREENS CHOKE FEEDING OF CRUSHER OPERATION IN STEADY STATE

CRUSHER INFO

SAMPLE NAME CRUSHER ID ON SITE CRUSHER MODEL MANTLE TYPE AND ALLOY CONCAVE TYPE AND ALLOY LINER HOURS UNDER LOAD ECCENTRIC THROW, mm ASRI PROGRAM MODE

TIME OF TEST

TEST DATA

CSS, mm POWER, kW AVG. PEAK PRESSURE, MPa AVG. PRESSURE, MPa A-DIM, mm SAVE DATA REPORT

SAMPLE DATA

No. OF SAMPLE BAGS BELT-CUT LENGTH, m BELT SPEED, m/min SAMPLE WEIGHT, kg CAPACITY, mtph FEED SAMPLE, Yes/No No. OF FEED BAGS

DOWNLOAD ASRI REPORT

TO BE ANALYZED IN LAB:

SAMPLE-ID IN BAGS

SAMPLE-ID IN BAGS

OVERVIEW PHOTOS

OVERVIEW PHOTOS

WORK INDEX STONES

WORK INDEX STONES

TRANSPORT TO LAB

OTHER:_________________________________________

Crushing Chamber Application Guide

159


CONVERSION TABLES LENGTH

UNITS

X

=

PRESSURE

kilometer

km

1,000

m

bar

ft

0.305

m

atm

mi

1,609

inch foot

yard mile

WEIGHT gram

tonne (metric ton) ton (short) ton (short) grains

ounce

troy ounce pound

AREA

yd

25.4

mm

0.914

m m

X

=

0.2777

907.2

kg

3.6

m/s

st

meters per second

km/h

km/hour

g

miles per hour miles per hour

mph

0.45

m/s

feet per hour

ft/h

0.305

mt t

1,000

2,000

gr

0.0646

t oz

31.1

oz lb

28.35

0.4536

kg lb g g

kg

0.8361

ft²

2

0.0929

UNITS

X

=

l

0.001

m3

cubic decimeter

dm3

1

cubic millimeter

mm3

0.0001

ft3

28.316

US gallon

FLOW RATE mass flow rate

volume flow rate

bar

UNITS

yd

Imperial gallon

0.06895

kilometers/hour

square yard

cubic yard

psi

bar

kPa

VELOCITY

=

cubic foot

6.895

=

mm²

cubic inch

pounds/in2 (psi)

bar

kg

X

cubic centimeter

1.01

X

645

milliliter

0.98

0.001

in²

liter

= kPa

g

UNITS

VOLUME

kp/cm2

X 100

UNITS

square inch square foot

160

in

UNITS

ml

cm3 in3

0.001

l l

l

4.544

X 1.1

0.028

l

UNITS kHz

rpm

1.61

km/hour m/hour

X

=

0.017

Hz

0.01667

r/sec

1,000

Hz

UNITS

X

=

kN

1,000

N

pound-force

lbf

4.45

N

kilopond

lbf ft

l

mph

kilo Newton

ml

3.785

Crushing Chamber Application Guide

FORCE

16.39

US gal

scfm

rev. per minute

TORQUE

ml

m3

mtph

kiloHertz

ml

0.7646

UNITS

blows/minute

1

yd3

Imp gal

FREQUENCY

m/s

kilopond meter

kp

9.81

N

UNITS

X

=

kpm

9.81

Nm

lbf ft

1.36

Nm

POWER

UNITS

X

=

kilowatt

kW

1,000

W

horsepower

hp

0.746

kW

degrees Fahrenheit

(°Cx9/5)+32

°F

degrees Celsius

(°F-32)x5/9

°C

= stph

m3/min

TEMPERATURE

UNITS

=


NOTES

Crushing Chamber Application Guide

161


162

Crushing Chamber Application Guide


Crushing Chamber Application Guide

163


Test results and calculations are to be considered as results reached under certain and controlled conditions. These test results and calculations should not be treated as specifications and Sandvik does not guarantee, warrant or represent the outcome of test results or calculations in any or all circumstances. Sandvik Mining and Rock Technology reserves the right to make changes to the information on this Application Guide without prior notification to users. Please contact a Sandvik representative for clarification on specifications and options. SANDVIK, SANDLOCK, FLEXIFEED, OPTIAGG, ASRI, PLANTDESIGNER and HYDROCONE are trademarks owned by the Sandvik Group of companies. The omission of a trademark from this list does not constitute a waiver of any rights of the Sandvik Group of companies relating to such trademark.

C5-1086:01ENG Š SANDVIK AB 2019 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without permission in writing from the Sandvik Group of companies.

Printed by Elanders Sverige AB, 2019

ROCKTECHNOLOGY.SANDVIK


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.