© Silke Steuernagel 2016 banner: designed by Freepic
FREEBIE
FREEBIE E-Book/Tutorial
Bracelet
Lunaxia A Design with CoCo-Beads by G&B-Beads.cz (www.gbbeads.cz)
page 1 , © Silke Steuernagel 2016
material 10 Swarovski-Crystal Pearls #5810 8 mm crystal bright gold pearl, CP 11 GB-Beads Coco-Beads #111-77786 horizontal/2-hole beads color: 0300/23601; CC 40 Swarovski- round faceted beads #5000 4 mm smoked topaz; RF 1 g Toho Seed Beads 11/0 marbled opaque avocado/pink #1209; SB11 1 g Toho Seed Beads 15/0 permanent finish galvanized starlight #PF557; SB15 1 Toggle Clasp 1,3/1,8 mm gold 4 Jump Rings 3,8 mm 20 gauge gold Thread Toho OneG white 1 Beading Needle #12 Scissors, 2 flat Pliers
Key
LEVEL X
# Beads which are added in a step are outlined in red.
Size
# Beads which are being passed in a step are outlined in blue.
Beginner
7.68“ long 0.51“ wide
Tutorial 1
3
Cut off an arm´s span of thread and thread into needle. About 6‘‘ before end of thread add a stop bead: Pass that bead twice.
Pick up 2 SB11 and again pass through the 1st hole of the CC and the 2 SB11 of step 2. Change direction and again pass through the 2nd hole of the CC of step 2.
2
4
Pick up 1 CC, pass 1st hole, pick up 2 SB11 and pass back through the 2nd hole of the CC.
Pick up 1 RF, 1 SB11, 1 CP, 1 SB11 and 1 RF. Circle through the 2nd hole of the CC of step 2 once again. Pass forward through the RF, SB11 and CP of this step.
page 2 , Š Silke Steuernagel 2016
5 Pick up 1 SB11, 1 RF, 1 CC (1st hole), 1 RF and 1 SB11. Circle through the CP of last step and pass forward through the SB11, RF and CC of this step.
6
Pick up 2 SB11 and circle through the 2nd hole of the CC of step 5. Pick up 2 SB11 and once again pass through the 1st hole of the CC of the last step. Pass forward through the 2 SB11 of this step and the again through the 2nd hole of the CC.
7 Repeat step 4.
8 Repeat step 5.
9 Repeat step 6.
10 11
Continue and repeat steps 3-9 until all CP and CC are used up.
Exit the last CC and pick up 4 SB11, 1 jump ring and 4 SB11. Circle through the same hole of the last CC once again. Pass all SB11 and the jump ring of this step and pass forward through the 1st SB11 above the CC.
page 3, © Silke Steuernagel 2016
12
13
Pick up 1 SB15 and pass forward along the edge through 1 Roc11, 1 RF and 1 SB11. Repeat this step to the end of the bracelet. You will pass only 1 SB11 at the last repetition.
Pick up 4 SB11, 1 jump ring and 4 SB11. Pass the outer hole of the last CC and again pass all SB11 and the jump ring of this step. Pass through the 1st SB11 below the last CC.
14
Repeat step 12 along the lower edge.
15
Once again pass the top edge of the bracelet. Pass forward to the thread of the beginning and remove the stop bead. Knot threads, sew up ends and cut off.
16
Using the 2 pliers open 1st jump ring, add the ring of the clasp and close the jump ring. At the opposite side open the jump ring, successively attach 2 more jump rings and the ring of the toggle. Close all jump rings.
TIP
...to adjust the length of the bracelet: 1 added repetition (consisting of 1 CC and 1 CP according to instruction) results roughly in about 8 mm/0.31‘‘ of extra length.
silke@starperlen.de www.starperlen.de starperlenschmuck.blogspot.com
© StarPerlen, Silke Steuernagel, all rights reserved Author, Concept, Design, Graphics, Composition and Photos: Silke Steuernagel, 2016 Material information, steps and description were checked carefully by the author. The author assumes no liability for possible damage and mistakes and is not held responsible. Commercial use (even in workshops) is allowed but the sale of this instruction is not allowed. The instruction (even in workshops) must be given/passed on free of charge. The instruction can be offered free of charge on all private and commercial websites. Grafics main page: designed by Freepik