Козырьки by mavo

ACCESSORIES FOR OUTDOORS

glass system technology

BALUSTRADES

C ONCEPT

DESIGN BY:

ARCH. GIUSEPPE INZITARI

DESIGN REGISTERED IN THE

EUROPEAN UNION -

BALUSTRADES

ACCESSORIES FOR OUTDOORS CANOPIES

ACCESSORIES FOR OUTDOORS

GLASS CANOPY Page 60

CANOPY LIGHT Page 72

CANOPY LIGHT WITH STRUT Page 77

FACADES

ROTULES Page 85

SPIDER Page 91

BALUSTRADES ACCESSORIES FOR OUTDOORS

CANOPIES GLASS CANOPY

PROJECT

DuPont™ SentryGlas® canopymade up of 3 panes of the following dimensions: length L = 1200 mm, overhang H = 4300 mm. Tested considering an accidental load equal to 160 kg/m2 and the panel weight of 260 kg. 60

DuPont™ and SentryGlas® are commercial brands or registered commercial brands of E. I. du Pont de Nemours and Company or of its affiliated companies.

BY:

ARCH. GIUSEPPE INZITARI

ING. SAMUELE PIAZZINI

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY GLASS CANOPIES FOR BIG OVERHANGS

GLASS CANOPY

buildings for which one wishes to preserve the original aesthetic impact, as well as for installation in new buildings to ensure maximum transparency and elegance. The innovative tie rod system is the result of collaboration between our Technical Department and the University of Florence, Department of Mechanics and Industrial Technologies. Obtained via AISI 316L stainless steel mechanical processing, this system offers a new design concept whose novelty is to have a rotule with a 45째 slanted pivot. This structure differs from those currently on the market as the tie rod is connected directly to the ball-joint ball, minimising eccentricity that could cause tension, resulting in the glass panel breaking; that is why the system is ideal for overhangs of substantial dimensions, ensuring safety in line with the regulations in force.

canopymade up of 4 panes of the following dimensions: length L = 1500 mm, overhang H = 3000 mm, with 3 tie rods. Tested considering an accidental load equal to 160 kg/m2 and the panel weight of 225 kg.

GLASS CANOPY

GLASS CANOPY details 61

ACCESSORIES FOR OUTDOORS

Hung glass and steel canopies are gaining ever more importance in the architectural landscape, both for coverage of historical

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY IDEA GENERATION The current market offers a number of canopies that, while differing in design, lead to the diagram shown in the figures to the side, i.e. the glass is held by four traditional rotules suitably anchored to the wall and to the various accessories.

Traditional diagram of the canopies on the market.

(F)

Please note that the force (F) acting from the tie rod to the front rotule, has a direction of about 45° compared to the axis of the threaded pivot.

Diagram of the direction of the force acting on the rotule

B Behaviour of the front rotule before (A) and after (B) the installation of the canopy.

Once on-stream, the balance configuration of the canopy goes from diagram A to diagram B as shown in the figure; so the threaded pivot of the front rotule tends to align itself along the tie rod axis. Usually, traditional rotules allow an adjustment of ± 10° according to the axis of the threaded pivot and therefore, knowing that the tie rod is slanted by about 45°, one can never achieve perfect alignment. In this situation the glass no longer works as hinged, but as jammed, thus considerably increasing the stresses on the panel, near the hole.

(F)

Hence the idea of making a special rotule, where the threaded pivot always works according to its own axis, as shown in the figures to the side.

New type of rotule, with M14 threaded pivot slanted at 45° with ±10° adjustment.

In every on-stream configuration, thanks to this new system, the tie rod and the threaded pivot are perfectly aligned so the glass is always hinged. One therefore achieves greater canopy stability, considerably reducing the stresses on the panel.

The new 45° rotule has been tested on the assembled elements via the Ansys calculation code. The test has been carried out by applying a load (F) along the direction of the tie rod equal to 3500N. 62

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY ARTICULATED 45° ROTULE Ø55xM14 - AISI 316L

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel with white PVC gasket. Features: new type of rotule designed by us, with M14 1.5 mm pitch threaded pivot slanted at 45°±10° including fixing boss and Ø55 mm locking ring nut. The pivot is supplied with the milling necessary for adjustment during assembly with the aid of a 12 mm spanner. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 25.52 mm. Finish: mill finish.

F max = 550 daN (1 daN corresponds to a weight of approx.1 kg) -

DESIGN REGISTERED IN THE

EUROPEAN UNION -

CONCLUSIONS:

TENSILE STRENGTH TEST - F

The load tests were performed with the universal testing machine MTS810, equipped with hydraulic Instron grips. The equipment used for load application were designed to reproduce the real operating conditions. A tensile load was applied in axis with the threaded pivot, until breakage, operating with displacement control loading (5 mm/min) and measuring the force applied 20 times per second. The chart indicates the results relating to the worst of the 5 samples tested. 3500 3000

Charge(daN) (daN) Carico

2500 2000 1500 1000 500

7.5 10.0 Spostamento(mm) (mm) Displacement

12.5

Glass hole Ø36 mm

ARTICULATED 45° ROTULE Ø46xM14 COUNTERSUNK AISI 316L

15.0

Q.ty 1 Pc

D E

Material: AISI 316L mechanically processed steel with white PVC gasket. Features: new type of rotule designed by us, with M14 1.5 mm pitch threaded pivot slanted at 45°±10° including Ø46 mm countersunk fixing boss and Ø55 mm locking ring nut. The pivot is supplied with the milling necessary for adjustment during assembly with the aid of a 12 mm spanner. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 26 mm. Finish: mill finish.

Dimensions A 10° B M14 C Ø55 mm D 43 mm S 10/25.52 mm

5.0

Art. GC-ROT145

2.5

0 0.0

DESIGN REGISTERED IN THE

Art. GC-ROT145S

EUROPEAN UNION -

F max = 550 daN (1 daN corresponds to a weight of approx.1 kg)

Dimensions A 10° B M14 C Ø46 mm D 43 mm E 5 mm F 5 mm minimum S 10/26 mm

Glass hole Ø36 mm countersunk 5 mm deep

Q.ty 1 Pc 63

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY ARTICULATED ROTULE Ø55xM14 - AISI 316L

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel with white PVC gasket. Features: rotule with M14 1.5 mm pitch threaded pivot with ±10° variable inclination including fixing boss and Ø55 mm locking ring nut. The pivot is fitted with a hexagon socket, located at the end, necessary for adjusting during assembly with an 8 mm hex key. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 25.52 mm. Finish: mill finish.

Ft max = 500 daN DESIGN REGISTERED IN THE

EUROPEAN UNION -

TENSILE STRENGTH TEST - Fn

SHEAR STRENGTH TEST - Ft

Fn max = 380 daN

Ft max = 500 daN

(1 daN corresponds to a weight of approx.1 kg)

For conclusions see page 41

3500

3000

2500

Charge(daN) (daN) Carico

2000 1500

1000

500

0 0.0

Art. GC-ROT101

2.5

(1 daN corresponds to a weight of approx.1 kg)

5.0

7.5 10.0 Spostamento(mm) (mm) Displacement

12.5

15.0

0 0.0

2.5

Dimensions A 10° B M14 C Ø55 mm D 63 mm S 10/25.52 mm

5.0

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

15.0

Glass hole Ø36 mm

Fn A

Material: AISI 316L mechanically processed steel with white PVC gasket. Features: rotule with M14 1.5 mm pitch threaded pivot with ±10° variable inclination including Ø46 mm countersunk fixing boss and Ø55 mm locking ring nut. The pivot is fitted with a hexagon socket, located at the end, necessary for adjusting during assembly with an 8 mm hex key. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 29 mm. Finish: mill finish.

Art. GC-ROT101S 64

(1 daN corresponds to a weight of approx.1 kg)

Dimensions A 10° B M14 C Ø46 mm D 63 mm E 5 mm F 5 mm minimum S 10/29 mm

EUROPEAN UNION -

Ft max = 500 daN DESIGN REGISTERED IN THE

20.0

Q.ty 1 Pc

ARTICULATED ROTULE Ø46xM14 COUNTERSUNK AISI 316L

17.5

Glass hole Ø36 mm countersunk 5 mm deep

Q.ty 1 Pc

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY WALL CONNECTOR Ø30x120 mm WITH STUDDED ROTULE Material: AISI 316L mechanically processed steel. Features: wall fixing connector with M22x150 mm 1.5 mm pitch threaded bar, Ø60 mm wall boss and M8 rotule grub screw. To be calculated separately and on customer request, we can supply the threaded bar of the desired length. Finish: mill finish.

ACCESSORIES FOR OUTDOORS

WALL PARETE

Art. GC-PEROUT162

Dimensions A 95 mm B Ø60 mm C Ø55 mm D 63 mm E 36 mm

Glass hole Ø36 mm

Q.ty 1 Pc

WALL CONNECTOR Ø30x120 mm - AISI 316L

WALL PARETE

Material: AISI 316L mechanically processed steel. Features: wall fixing connector with M22x150 mm 1.5 mm pitch threaded bar, Ø60 mm diameter wall boss and M8 rotule grub screw. To be calculated separately and on customer request, we can supply the threaded bar of the desired length. Finish: mill finish. F max = 500 daN (1 daN corresponds to a weight of approx.1 kg)

Check the resistance characteristics of the anchoring wall. Art. GC-PERN120

Dimensions A 95 mm B Ø60 mm C Ø30 mm D 120 mm E 36 mm

Wall anchoring SOUDAFIX VE280/380-SF

Q.ty 1 Pc

WALL JOINT Ø30x43 mm - AISI 316L

WALL PARETE

Material: AISI 316L mechanically processed steel. Features: wall fixing joint with M22x150 mm 1.5 mm pitch threaded bar, Ø60 mm boss and special tightening nut for Ø10 mm tie rod. To be calculated separately and on customer request, we can supply the threaded bar of the desired length. Finish: mill finish. F max = 600 daN F

(1 daN corresponds to a weight of approx.1 kg)

Art. GC-SNOD143

Dimensions A 43 mm B Ø60 mm C Ø30 mm E 21 mm

Wall anchoring SOUDAFIX VE280/380-SF

E A

Check the resistance characteristics of the anchoring wall.

Q.ty 1 Pc 65

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY Ø10 TIE ROD - AISI 316L

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel. Features: Ø10 mm round bar with M10x50 mm threaded ends with left-hand thread, of variable length according to the customer request (see diagrams on page 26-27). Finish: mill finish. N.B. For tie rods exceeding 3 metres use Art: GC-GZT130

Art. GC-CAV100 GC-CAV300

Dimensions A M10 with left-hand thread B 50 mm C up to 1500 mm A M10 with left-hand thread B 50 mm C from 1500 to 3000 mm

Q.ty 1 Pc 1 Pc

TENSIONER Ø30 mm - AISI 316L Material: AISI 316L mechanically processed steel. Features: Ø30 mm tensioner which allows to adjust the canopy slope thanks to the four dead holes placed around it using the pin spanner. Adjustment length ±10 mm. Finish: mill finish. 5mm 26mm

Art. GC-TEND130

Dimensions A Ø30 mm B 94 mm C M10 with left-hand thread D M14

Adjustment d = 5/35 mm

Q.ty 1 Pc

CONNECTING PIN Ø30x270 mm - AISI 316L Material: AISI 316L steel. Features: pin for connecting two adjacent panels, fitted with M14x68 mm 1.5 mm pitch threaded bar. Finish: mill finish.

N.B. If the connecting pin is used, the length of tie rod “C”, calculated according to the formulae of page 26-27, must be reduced by 35 mm.

A B

Art. GC-PERN270 66

Dimensions A 220 mm B 270 mm C Ø30 mm D 46 mm

Q.ty 1 Pc

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY JOINT FOR TIE RODS Ø30 mm - AISI 316L

Art. GC-GZT130

Dimensions A Ø30 mm B 94 mm C M10 with left-hand thread D 10 mm

Q.ty 1 Pc

THREAD COVER CYLINDER - AISI 316L Material: AISI 316L steel. Features: Ø18 mm cylinder with M14 1.5 mm pitch threaded blind hole and radial washer for finishing the wall-mounted pin. Finish: mill finish.

C A

Art. GC-TPP116

Dimensions A Ø18 mm B 40 mm C 16 mm D Ø30 mm

Q.ty 1 Pc

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel. Features: Ø30 mm joint for connecting M10 left-hand thread rods, in the event of tie rods exceeding 3 m. Finish: mill finish

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY

TIE ROD

TIE ROD WITH WALL CONNECTIONS

GC-SNOD143

GC-CAV100 GC-CAV300

GC-PERN120

GC-TEND130

GC-ROT145 GC-ROT145S

Art. GC-SNOD1100 GC-SNOD1145 GC-SNOD1300 GC-SNOD1345

Dimensions With Ø55 bosses and cable max L=1500 mm With countersunk bosses and cable max L=1500 mm With Ø55 bosses and cable L max=3000 mm With countersunk bosses and cable max L=3000 mm

TIE ROD WITH CONNECTING PIN

Q.ty 1 Set 1 Set 1 Set 1 Set

GC-TEND130

GC-ROT101 GC-ROT101S

Art. GC-CAV1100 GC-CAV1145 GC-CAV1300 GC-CAV1345

GC-ROT145 GC-ROT145S

Dimensions With Ø55 bosses and cable max L=1500 mm With countersunk bosses and cable max L=1500 mm With Ø55 bosses and cable L max=3000 mm With countersunk bosses and cable max L=3000 mm

TIE ROD WITH CONNECTING PIN AND WALL CONNECTIONS

GC-SNOD143

GC-CAV100 GC-CAV300

GC-SNOD143

Q.ty 1 Set 1 Set 1 Set 1 Set

GC-SNOD143

GC-CAV100 GC-CAV300

GC-PERN120

GC-TEND130

GC-ROT101 GC-ROT101S

GC-ROT145 GC-ROT145S

Art. GC-PERN155 GC-PERN145 GC-PERN355 GC-PERN345 68

GC-PERN270

Dimensions With Ø55 bosses and cable max L=1500 mm With countersunk bosses and cable max L=1500 mm With Ø55 bosses and cable L max=3000 mm With countersunk bosses and cable max L=3000 mm

Q.ty 1 Set 1 Set 1 Set 1 Set

GC-ROT145 GC-ROT145S

Art. GC-PEROUT155 GC-PEROUT145 GC-PEROUT355 GC-PEROUT345

GC-PERN270

Dimensions With Ø55 bosses and cable max L=1500 mm With countersunk bosses and cable max L=1500 mm With Ø55 bosses and cable L max=3000 mm With countersunk bosses and cable max L=3000 mm

Q.ty 1 Set 1 Set 1 Set 1 Set

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY

ACCESSORIES FOR OUTDOORS

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY DIAGRAM OF RECOMMENDED PANES The table below shows the indicative measures and the thicknesses recommended for the glass panels supported with the GLASS CANOPY system. The geometry of the panel was evaluated as if it were stratified tempered glass with PVB. The thickness of the glass was calculated considering an accidental load equal to 160 kg/m2 and the weight of the panel. For the calculation one also used the safety coefficients required by Draft Standard PrEN13474-3, whereby the mechanical behaviour of stratified safety glass (according to UNI7697) narrows down to the analysis of equivalent monolithic glass. In the event of tempered glass it is recommended to subsequently subject it to the HST treatment (Heat Soak Test) to drastically reduce the risks of spontaneous breakage. 85

WALL MURO SIDE LATO

Ih H

Type tipo A

Type A - 2 Tie rods

Type B - 3 Tie rods

Ih H

Type tipo B

Type

WALLMURO SIDE LATO

Il L

L (mm)

H (mm)

Il (mm)

Ih (mm)

Tempered + PVB + Tempered

Glass hole (mm)

1500

1000

6 + 6 + 1.52

Ø36

2200

1300

1700

8 + 8 + 1.52

Ø36

2500

1400

1800

10 + 10 + 1.52

Ø36

2500

1500

900

1100

6 + 6 + 1.52

Ø36

3000

2000

1000

1400

8 + 8 + 1.52

Ø36

3800

2400

1400

1800

10 + 10 + 1.52

Ø36

N.B.: it is recommended to use the SentryGlas® interlayer instead of the PVB, to ensure residual strength of the glass in the event of breakage of both panels, which is not guaranteed by the PVB .

DuPont™ SentryGlas®

NORMAL HOLE With Ih given: C = Ih x 1.4 – 34 h = Ih + 119 h’ = Ih + 34

With h given: C = h x 1.4 – 202 Ih max = h – 119 With h’ given: C = h’ x 1.4 – 83 Ih max = h’ – 34

45°

DuPont™ and SentryGlas® are commercial brands or registered commercial brands of E. I. du Pont de Nemours and Company or of its affiliated companies.

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - GLASS CANOPY DIAGRAM OF PANES RECOMMENDED FOR BIG OVERHANGS

WALLMURO SIDE LATO

Type tipo CC

WALL LATOSIDE MURO

tipo DD Type

Il L

Type

L (mm)

H (mm)

Il (mm)

Ih (mm)

Type C - 4 Tie rods

1500

3000

1000

2200

3500

1300

2500

3000

3500

Type D - 6 Tie rods

Tempered + PVB + Tempered

Glass hole (mm)

1200

8 + 8 + 1.52

Ø36

1400

10 + 10 + 1.52

Ø36

900

1200

8 + 8 + 1.52

Ø36

1200

1300

10 + 10 + 1.52

Ø36

N.B.: it is recommended to use the SentryGlas® interlayer instead of the PVB, to ensure residual strength of the glass in the event of breakage of both panels, which is not guaranteed by the PVB . C' NORMAL HOLE

DuPont™ SentryGlas®

With Ih given: C = Ih x 1.4 – 34 C’= C + 10 h = Ih + 119 h’ = Ih + 34 With h given: C = h x 1.4 – 202 C’= C + 10 Ih max = h – 119

DuPont™ and SentryGlas® are commercial brands or registered commercial brands of E. I. du Pont de Nemours and Company or of its affiliated companies. C'

With h’ given: C = h’ x 1.4 – 83 C’= C + 10 Ih max = h’ – 34 95

45°

Ih 71

ACCESSORIES FOR OUTDOORS

The table below shows the indicative measures and the thicknesses recommended for the glass panels supported with the GLASS CANOPY system. The geometry of the panel was evaluated as if it were stratified tempered glass with PVB. The thickness of the glass was calculated considering an accidental load equal to 160 kg/m2 and the weight of the panel. For the calculation one also used the safety coefficients required by Draft Standard PrEN13474-3, whereby the mechanical behaviour of stratified safety glass (according to UNI7697) narrows down to the analysis of equivalent monolithic glass. In the event of tempered glass it is recommended to subsequently subject it to the HST treatment (Heat Soak Test) to drastically reduce the risks of spontaneous breakage.

BALUSTRADES

CANOPY LIGHT

ACCESSORIES FOR OUTDOORS

REGISTERED MODEL

C ONCEPT

DESIGN BY:

ARCH. GIUSEPPE INZITARI

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT CANOPY LIGHT CANOPY – WALL JOINT

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel Features: wall joint with Ø10 mm joining pin. Finish: mill finish F max = 400 daN (1 daN corresponds to a weight of approx.1 kg)

Grub screw M4 x 6 mm

Check the resistance characteristics of the anchoring wall. F

Ø45

M16

1M01 si0n l isetft ro

35 M

135

45° 0°/

REGISTERED MODEL

Art. GCL21

Dimensions Boss Ø45 mm - Bar M16 x 135 mm - Angle 0 / 45°

Wall anchoring Soudafix VE 280/380-SF

Q.ty 1 Pc

CANOPY LIGHT CANOPY – ARTICULATED BOSS Material: AISI 316L mechanically processed steel Features: glass boss with Ø10 mm joining pin. Finish: mill finish F max = 400 daN (1 daN corresponds to a weight of approx.1 kg)

Grub screw M4 x 6 mm

0°/ 45°

ch8

35 Ø45

REGISTERED MODEL

Art. GCL15

Dimensions Boss Ø45 mm - Angle 0 / 45° - L = 35 mm

Glass hole Ø30 mm

Glass thickness 11.52 - 17.52 mm

Q.ty 1 Pc 73

CANOPY LIGHT CANOPY – TIE ROD Material: AISI 316L mechanically processed steel Features: Ø10 mm tie rod threaded at the M10 and M10 left ends respectively. Finish: satin-finished steel N.B. To calculate C refer to the diagram on the next page.

C = max 1500

M10 left sinistro M10

Ch8

M10

Art. GCL23

Dimensions Ø10 mm x maximum length 1500 mm

Q.ty 1 Pc

CANOPY LIGHT CANOPY – WALL CONNECTOR Material: AISI 316L mechanically processed steel Features: wall connector with Ø10 mm joining pin. Finish: mill finish F max = 400 daN (1 daN corresponds to a weight of approx.1 kg) F 55

Check the resistance characteristics of the anchoring wall.

Ø45

0° /9 0°

135

Grub screw M4 x 6 mm

REGISTERED MODEL

Art. GCL19 74

Dimensions Boss Ø45 mm - Angle 0 / 90° - L = 55 mm

Glass hole Ø30 mm

Wall anchoring Soudafix VE 280/380-SF

Glass thickness 11.52 - 17.52 mm

Q.ty 1 Pc

5 Ø45

M16

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT DIAGRAM OF RECOMMENDED PANES

WALL SIDE LATO MURO

WALLMURO SIDE LATO

Ih H

Type tipo EE

Type E - 2 Tie rods

Type F - 3 Tie rods

Ih H

Type tipo FF

Type

L (mm)

H (mm)

Il (mm)

Ih (mm)

Tempered + PVB + Tempered

Glass hole (mm)

1500

1000

700

5 + 5 + 1.52

Ø30

1800

1200

1100

800

6 + 6 + 1.52

Ø30

2200

1500

1400

1200

8 + 8 + 1.52

Ø30

2500

1000

700

5 + 5 + 1.52

Ø30

2800

1200

1100

800

6 + 6 + 1.52

Ø30

3200

1500

1400

1200

8 + 8 + 1.52

Ø30

N.B.: it is recommended to use the SentryGlas® interlayer instead of the PVB, to ensure residual strength of the glass in the event of breakage of both panels, which is not guaranteed by the PVB .

5°

Ø30

max 45°

Ø30

4 max

ma x4

With h given: C = h x 1.4 – 115 Ih max = h – 70

DuPont™ and SentryGlas® are commercial brands or registered commercial brands of E. I. du Pont de Nemours and Company or of its affiliated companies.

With Ih given: C = Ih x 1.4 – 15 h = Ih + 70

DuPont™ SentryGlas®

m ±5 C

NORMAL HOLE (angle of 45° between glass and tie rod)

ACCESSORIES FOR OUTDOORS

BALUSTRADES

CANOPY LIGHT - ASSEMBLY STAGES STAGE 1

STAGE 2

mm C±5

ACCESSORIES FOR OUTDOORS

H Ih

STAGE 3

BALUSTRADES

CANOPY LIGHT WITH STRUT REGISTERED MODEL

ACCESSORIES FOR OUTDOORS

CONCEPT

DESIGN BY:

ARCH. GIUSEPPE INZITARI

Ø45

45° 0 °/

Grub screw M4 x 6 mm

REGISTERED MODEL

Art. GCL15

Dimensions Boss Ø45 mm - Angle 0 / 45°

Glass hole Ø30 mm

Glass thickness 11.52 - 17.52 mm

Q.ty 1 Pc

CANOPY LIGHT CANOPY – WALL JOINT Material: AISI 316L mechanically processed steel Features: wall joint with Ø10 mm joining pin. Finish: mill finish F max = 400 daN (1 daN corresponds to a weight of approx.1 kg)

Check the resistance characteristics of the anchoring wall.

0°/ 45° F 36

Ø45

M16

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT

135

Grub screw M4 x 6 mm

REGISTERED MODEL

Art. GCL21 78

Dimensions Boss Ø45 mm - Bar M16 x 135 mm - Angle 0 / 45°

Wall anchoring Soudafix VE 280/380-SF

Q.ty 1 Pc

BALUSTRADES

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT CANOPY LIGHT CANOPY – STRUT

ACCESSORIES FOR OUTDOORS

Material: AISI 316L mechanically processed steel Features: pipe Ø25 x 2 mm thick, with connectors at the M10 and M10 left ends respectively. Finish: satin-finished steel N.B. To calculate C refer to the diagram on the next page. Ø25

C' = max 1500

M10

M10sinistro left M10

Art. GCL51

Dimensions Ø25 mm - Thickness 2 mm - max L 1500 mm

Q.ty 1 Pc

Check the resistance characteristics of the anchoring wall.

55 5

Ø45

M16 135

0° /9 0°

Ø45

Grub screw M4 x 6 mm

REGISTERED MODEL

Art. GCL19

Dimensions Boss Ø45 mm - Angle 0 / 90° - L = 55 mm

Glass hole Ø30 mm

Wall anchoring Soudafix VE 280/380-SF

Glass thickness 11.52 - 17.52 mm

Q.ty 1 Pc 79

DIAGRAM OF RECOMMENDED PANES The table below shows the indicative measures and the thicknesses recommended for the glass panels supported with the GLASS CANOPY system. The geometry of the panel was evaluated as if it were stratified tempered glass with PVB. The thickness of the glass was calculated considering an accidental load equal to 160 kg/m2 and the weight of the panel. For the calculation one also used the safety coefficients required by Draft Standard PrEN13474-3, whereby the mechanical behaviour of stratified safety glass (according to UNI7697) narrows down to the analysis of equivalent monolithic glass. In the event of tempered glass it is recommended to subsequently subject it to the HST treatment (Heat Soak Test) to drastically reduce the risks of spontaneous breakage. WALL MURO SIDE LATO

WALLMURO SIDE LATO

Ih H

Type tipo G G

Type G - 2 Tie rods

Type H - 3 Tie rods

Ih H

Type

Type tipo H

L (mm)

H (mm)

Il (mm)

Ih (mm)

Tempered + PVB + Tempered

Glass hole (mm)

1500

1000

700

5 + 5 + 1.52

Ø30

1800

1200

1100

800

6 + 6 + 1.52

Ø30

2200

1500

1400

1200

8 + 8 + 1.52

Ø30

2500

1000

700

5 + 5 + 1.52

Ø30

2800

1200

1100

800

6 + 6 + 1.52

Ø30

3200

1500

1400

1200

8 + 8 + 1.52

Ø30

N.B.: it is recommended to use the SentryGlas® interlayer instead of the PVB, to ensure residual strength of the glass in the event of 45

Ih Ø30

Ø30

5° x4 ma Ø 25 x 2

45 °

m C '= C -1 02 m a r fo

il ta gl io

y ar ss e ec N

N ec es sa

ri o

e th

be tu

m is

With h given: C = h x 1.4 C’= C – 102 Ih max = h – 19

ze si

de lt ub o

max

m m

ur a

With Ih given: C = Ih x 1.4 +27 C’= C – 102 h = Ih + 19

max 45 °

NORMAL HOLE (angle of 45° between glass and tie rod)

guaranteed by the PVB .

breakage of both panels, which is not

BALUSTRADES ACCESSORIES FOR OUTDOORS

SYSTEM FOR GLASS CANOPIES - CANOPY LIGHT

o tt cu

DuPont™ SentryGlas® DuPont™ and SentryGlas® are commercial brands or registered commercial brands of E. I. du Pont de Nemours and Company or of its affiliated companies.

BALUSTRADES

CANOPY LIGHT - ASSEMBLY STAGES STAGE 1

STAGE 2

45 Ih

ACCESSORIES FOR OUTDOORS

STAGE 3

BALUSTRADES

TOOLS - ACCESSORIES SILIRUB NO5 T - NEUTRAL SILICONE FOR BUILDING, DOORS AND WINDOWS

ACCESSORIES FOR OUTDOORS

Description: SILIRUB NO5 T is a silicone sealant, neutral, rapid cure (oxime type), compliant with ISO 11600 Standards. Features: • Very good application on building surfaces including porous or synthetic materials • Rapid cure • Excellent resistance to UV rays and weathering • Resists at temperatures between -40°C and +180°C. • Unalterable colour • Permanent elasticity • SNJF label, 1st category, ISO 11600 Application: • Connecting joints between wood, PVC, aluminium • Expansion joints indoors and outdoors ISO 11600 F25LM/G25LM UNI 9610/9611 Skinning time: Approx. 5 min. (20°C/65% U. R.A.) Curing time: 2 mm/24h / (20°C/65% U. R.A.) Temperature resistance: from -40°C to +180°C Elasticity modulus: 0.25N/mm2 (DIN 53504) Elongation at break: > 750% (DIN 53504) Application temperature: from +5°C to 35°C

Art. SDNEU-N05

Format 300 ml

Hardness 25±5 Shore A

Colour Transparent

Paintable No

Q.ty 1 Pc

SOUDAFIX VE400-SF - ANCHORING RESIN Description: SOUDAFIX vinylester based, styrene free, two-component anchoring resin Features: • Easy to use Ø Bar M8 M10 M12 M16 M20 M24 M27 M30 • Fast cure • Styrene free (low odour) Ø Drill (mm) 10 12 14 18 24 28 28 35 • Impermeable fixing • High chemical resistance • Fire Resistance class F120 Application: • Pressure-free securing of anchoring rods, Soudafix VE400-SF pivots, reinforcing bars, threaded bars, Skinning time table (20°C/65% R.H.) profiles etc in solid and hollow materials, BEGINNING CURE TEMPERATURE edge reconstruction COMPLETE • Wide application area, it can even be used in presence of moisture, - 10°C 90 min 24 hours even under water and at temperatures - 5°C 90 min 14 hours below -5°C. 0 45 min 7 hours It can be used as mortar for concrete

5 Skinning time: see table Temperature resistance: from +80°C to +120°C Elasticity modulus: 4.087 N/mm2 Application temperature: from -10 to +40 Tensile strength: 17 N/mm2 Maximum compression strength: 80 N/mm2

Art. SDAC-280 SDAC-380 82

Format 280 ml 380 ml

Specific weight 1.66 g/cm3 1.66 g/cm3

25 min

2 hours

10°C

15 min

80 min

20°C

6 min

45 min

30°C

4 min

25 min

35°C

2 min

20 min

40°C

1.5 min

15 min

Colour Dark grey after mixing Dark grey after mixing

Q.ty 1 Pc 1 Pc

BALUSTRADES

TOOLS - ACCESSORIES GUN Professional gun for sealants

ACCESSORIES FOR OUTDOORS

Art. SDAC-017

Q.ty 1 Pc

GUN Professional gun for 380 ml format chemical anchor

Art. SDAC-021

Format 380 ml

Q.ty 1 Pc

FACE SPANNER FOR 3 mm DEAD HOLES Material: metal body, stainless steel pins. Practical tool for tightening screws with dead holes securely. Rubber handle to ease grip. Via the compass opening one can work on large radiuses, for pair of holes with variable centre-to-centre from 7 mm to 55 mm.

Art. UT300 UT300R

Dimensions Length 150 mm Pin Ø2.8 mm Spare pins

Q.ty 1 Pc 1 Pair

PIN SPANNER Material: AISI 304 steel. Features: tool necessary for tightening all the metallic parts with pairs of dead holes around their axis, for tensioner Art. GC-TEND130, GC-GZT130, GC_PEROUT162 and GC-PERN120.

Art. CHSETT19

Dimensions Length 125 mm Pin Ø2.8 mm Extension = Ø19/50 mm

For blind hole Ø3 mm

Q.ty 1 Pc 83

BALUSTRADES ACCESSORIES FOR OUTDOORS

FACADES

C ONCEPT

DESIGN BY:

ARCH. GIUSEPPE INZITARI

BALUSTRADES

FACADES

ACCESSORIES FOR OUTDOORS

In collaboration with:

ROTULE BREAKING TEST

TENSILE TEST - CONCLUSIONS:

SHEAR TEST - CONCLUSIONS:

The load tests were performed with the universal testing machine MTS810, equipped with hydraulic Instron grips. The equipment used for load application were designed to reproduce the real operating conditions. A tensile load was applied in orthogonal direction to the axis of the threaded pivot, operating with displacement control loading (5 mm/min) and measuring the force applied 20 times per second. The tests were interrupted in correspondence of a 3000 daN load, before breakage; however the samples show significant signs of permanent plastic deformation. The chart indicates the results relating to the worst of the 5 samples tested.

BALUSTRADES

FACADES - ROTULES

ACCESSORIES FOR OUTDOORS

ARTICULATED ROTULE Ø55xM14 - AISI 316L GLASS THICKNESS 10/25.52 mm Material: AISI 316L mechanically processed steel with white PVC gasket. Features: rotules with M14 1.5 mm pitch threaded pivot with ±10° variable inclination including fixing boss, Ø55 mm locking ring nut, 2 M14 nuts and 2 slotted washers and a spring washer. The pivot is fitted with a hexagon socket, located at the end, necessary for adjusting during assembly with an 8 mm hex key. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 25.52 mm. Finish: mill finish.

10°

M14x1.5

64 61 Ft

52 S

Ø32

TENSILE STRENGTH TEST - Fn

SHEAR STRENGTH TEST - Ft

Fn max = 380 daN

Ft max = 500 daN

(1 daN corresponds to a weight of approx.1 kg)

3500

3000

2500

Charge(daN) (daN) Carico

Ø55

2000 1500

1000

500

0 0.0

Art. ROT101V

2.5

Dimensions Ø55 mm

5.0

7.5 10.0 Spostamento(mm) (mm) Displacement

12.5

15.0

0 0.0

2.5

5.0

Glass hole Ø36 mm

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

15.0

17.5

Glass thickness S = 10 - 25.52 mm

Q.ty 1 Pc

ARTICULATED ROTULE Ø46xM14 COUNTERSUNK AISI 316L GLASS THICKNESS 10/29 mm

Material: AISI 316L mechanically processed steel with white PVC gasket. Features: rotules with M14 1.5 mm pitch threaded pivot with ±10° variable inclination including Ø46 mm countersunk fixing boss, Ø55 mm locking ring nut, 2 M14 nuts and 2 slotted washers and a spring washer. The pivot is fitted with a hexagon socket, located at the end, necessary for adjusting during assembly with an 8 mm hex key. Suitable for panes of variable thickness from a minimum of 10 mm to a maximum of 29 mm. Finish: mill finish. Fn max = 380 daN - Ft max = 500 daN

10°

M14x1.5

64 61 Ft

58 Ø32

Ø46

(1 daN corresponds to a weight of approx.1 kg)

Art. ROT101SV 86

Dimensions Ø46 mm

Glass hole Ø36 mm countersunk 5 mm deep

20.0

Glass thickness S = 10 - 29 mm

Q.ty 1 Pc

BALUSTRADES

FACADES - ROTULES ARTICULATED ROTULE Ø59xM14 - AISI 316 GLASS THICKNESS 11/36 mm

Fn ACCESSORIES FOR OUTDOORS

10°

M14x2

Material: AISI 316 steel with white PVC gasket. Features: rotule with M14 threaded pivot, with ±10° variable inclination including fixing boss and Ø59 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 11 mm to a maximum of 36 mm. Finish: mill finish.

32 8

12 Ft

64 S Ø34 Ø59

TENSILE STRENGTH TEST - Fn

SHEAR STRENGTH TEST - Ft

Fn max = 890 daN

Ft max = 500 daN

(1 daN corresponds to a weight of approx.1 kg)

3500

6000

3000 2500

4000

Charge(daN) (daN) Carico

3000

2000

Art. ROT02D

1500 1000

1000

0 0.0

2000

500

2.5

5.0

Dimensions Ø59 mm

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

15.0

17.5

20.0

0 0.0

2.5

5.0

Glass hole Ø36 mm

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

15.0

Glass thickness S = 11 - 36 mm

ARTICULATED ROTULE Ø59xM14 - AISI 316 GLASS THICKNESS 13/28 mm

17.5

20.0

Q.ty 1 Pc

10°

M14x2

22 56

32 8

Charge(daN) (daN) Carico

5000

58 S

Ø34 Ø59

Art. ROT02

Dimensions Ø59 mm

Glass hole Ø36 mm

Glass thickness S = 13 - 28 mm

Q.ty 1 Pc 87

BALUSTRADES

FACADES - ROTULES

ACCESSORIES FOR OUTDOORS

ARTICULATED ROTULE Ø60xM14 - AISI 316 GLASS THICKNESS 17/37 mm

Fn 10°

10°

M14x2

Material: AISI 316 steel with black PVC gasket. Features: rotule with M14 hot insert threaded pivot, with ±10° variable inclination including fixing boss and Ø60 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 17 mm to a maximum of 37 mm. Finish: mill finish.

18 20 11 58

13 Ft

67 S

Ø32 Ø60

TENSILE STRENGTH TEST - Fn

TENSILE STRENGTH TEST - Ft

Fn max = 780 daN

Ft max = 500 daN

(1 daN corresponds to a weight of approx.1 kg)

3500

6000

3000 2500

4000

Charge(daN) (daN) Carico

5000

3000

2000

Art. ROT35PT

1500 1000

1000

0 0.0

2000

500

2.5

5.0

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

Dimensions Ø60 mm

15.0

17.5

20.0

0 0.0

2.5

5.0

Glass hole Ø36 mm

7.5 10.0 12.5 Spostamento(mm) (mm) Displacement

15.0

17.5

Glass thickness S = 17 - 37 mm

20.0

Q.ty 1 Pc

ARTICULATED ROTULE Ø46xM14 COUNTERSUNK AISI 316 GLASS THICKNESS 18/38 mm

Fn 10°

10°

M14x2

Material: AISI 316 steel with black PVC gasket. Features: rotule with M14 hot insert threaded pivot, with ±10° variable inclination including Ø46 mm countersunk fixing boss and Ø60 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 18 mm to a maximum of 38 mm. Finish: mill finish. Fn max = 780 daN - Ft max = 500 daN (1 daN corresponds to a weight of approx.1 kg)

18 20 11 58

14 Ft

66 S

5 Ø36 Ø46 Ø60

Art. ROT35PZ 88

Dimensions Ø46 mm countersunk 5 mm

Glass hole Ø36 mm countersunk 5 mm deep

Glass thickness S = 18 - 38 mm

Q.ty 1 Pc

BALUSTRADES

FACADES - ROTULES

10°

ACCESSORIES FOR OUTDOORS

ARTICULATED ROTULE Ø60xM14 - AISI 316 GLASS THICKNESS 10.5/21 mm

M14x2 20 22 11 62

55 14 50 S Ø30 Ø60

Art. ROT19PT

Dimensions Ø60 mm

Glass hole Ø36 mm

Glass thickness S = 10.5 - 21 mm

ARTICULATED ROTULE Ø46xM14 COUNTERSUNK AISI 316 GLASS THICKNESS 12/22 mm

Q.ty 1 Pc

10°

M14x2

11 67

59 14 52 5

S Ø34 Ø46 Ø60

Art. ROT19PZ

Dimensions Ø46 mm countersunk 5 mm

Glass hole Ø36 mm countersunk 5 mm deep

Glass thickness S = 12 - 22 mm

ARTICULATED ROTULE FOR DOUBLE-GLAZING Ø59xM14 - AISI 316 GLASS THICKNESS 23/42 mm

Q.ty 1 Pc 10°

10°

M14x2

22 62

30 8

67 S

Ø36 Ø59

Art. ROT031

Dimensions Ø59 mm

Glass hole Ø40 mm

Glass thickness S = 23 - 42 mm

Q.ty 1 Pc 89

BALUSTRADES

FACADES - ROTULES

ACCESSORIES FOR OUTDOORS

ARTICULATED ROTULE Ø51xM10 - AISI 316 GLASS THICKNESS 11/20 mm

10°

Material: AISI 316 steel with white PVC gasket. Features: rotule with M10 threaded pivot, with ±10° variable inclination including fixing boss and Ø51 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 11 mm to a maximum of 20 mm. Finish: mill finish.

10°

M12x1.5 21

10 46 S Ø30

Ø51

Art. ROT06A

Dimensions Ø51 mm

Glass hole Ø32 mm

Glass thickness S = 11 - 20 mm

ARTICULATED ROTULE Ø46xM14 COUNTERSUNK AISI 316 GLASS THICKNESS 15/24 mm

Q.ty 1 Pc

10°

M14x2

Material: AISI 316 steel with white PVC gasket. Features: rotule with M14 threaded pivot, with ±10° variable inclination including Ø44 mm countersunk fixing boss and Ø59 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 15 mm to a maximum of 24 mm. Finish: mill finish.

22 63

30 8

13 54 5

S Ø35 Ø44 Ø59

Art. ROT01

Dimensions Ø44 mm countersunk 5 mm

Glass hole Ø36.5 mm countersunk 5 mm deep

Glass thickness S = 15 - 24 mm

ARTICULATED ROTULE Ø40xM10 COUNTERSUNK AISI 316 GLASS THICKNESS 12/17.5 mm Material: AISI 316 steel with white PVC gasket. Features: rotule with M14 threaded pivot, with ±10° variable inclination including Ø40 mm countersunk fixing boss and Ø59 mm locking ring nut. Supplied with two slotted washers, a spring washer, a nut and a finishing bushing. Suitable for panes of variable thickness from a minimum of 12 mm to a maximum of 17.5 mm. Finish: mill finish.

Q.ty 1 Pc

10°

M10x1.5

23 7

55 59 10

46 4

S Ø32

Ø40 Ø59

Art. ROT13 90

Dimensions Ø40 mm countersunk 5 mm

Glass hole Ø32 mm countersunk 4 mm deep

Glass thickness S = 12 - 17.5 mm

Q.ty 1 Pc

BALUSTRADES

FACADES - SPIDER

SPIDER STRENGTH TEST

ACCESSORIES FOR OUTDOORS

In collaboration with:

REFERENCE REGULATIONS: The tests were conducted according to the indications listed under point B6 of the technical document CSTB 3574 (2006) 91

SPIDER 4 WAY - AISI 316

Material: AISI 316 steel Features: spider 4-way for the connection of 4 rotules to the load-bearing structure. Finish: polished steel.

38 Ø 15 37 Ø

5 5.

Ø 26

220

38 Ø

Ø19

5 5.

15 20

26 17

20 A-A

110

STRENGTH TEST IN ORTHOGONAL DIRECTION TO THE FACADE

STRENGTH TEST IN PARALLEL DIRECTION TO THE FACADE

Force (f) = 204.3 daN Value (f) detected in correspondence

Force (f) = 415.3 daN Value (f) detected in correspondence

of a movement of 1 mm

(1 daN corresponds to a weight of approx.1 kg)

9 6 8 5

7 6

Charge (daN) Carico (kN)

BALUSTRADES ACCESSORIES FOR OUTDOORS

FACADES - SPIDER

(f )

5 4 3

(f )

2 1 1 0

Art. SP2201 92

0.5

1.5 2 2.5 Spostamento (mm) Displacement (mm)

Centre-to-centre 220 mm

3.5

Weight 2100 g

0.5

1 1.5 Spostamento (mm) Displacement (mm)

2.5

Q.ty 1 Pc

BALUSTRADES

FACADES - SPIDER SPIDER 2 WAY IN-LINE - AISI 316

110

Ø38

Ø37

STRENGTH TEST IN PARALLEL DIRECTION TO THE FACADE

Force (f) = 461.1 daN Value (f) detected in correspondence

Force (f) = 477.5 daN Value (f) detected in correspondence

of a movement of 1 mm

(1 daN corresponds to a weight of approx.1 kg)

Charge (daN) Carico (kN)

12 Charge (daN) Carico (kN)

18 A-A

STRENGTH TEST IN ORTHOGONAL DIRECTION TO THE FACADE

(f )

10 8 6

(f )

5 4 3 2

2 0

14.4

9 Ø1

Ø2 6

Ø38

24.5

ACCESSORIES FOR OUTDOORS

Material: AISI 316 steel Features: spider 2-way in-line for the connection of 2 rotules to the load-bearing structure. Finish: polished steel.

Art. SP2202

0.5

1.5 2 2.5 Spostamento (mm) Displacement (mm)

Centre-to-centre 220 mm

3.5

Weight 950 g

0.5

1.5 2 Spostamento (mm) Displacement (mm)

2.5

Q.ty 1 Pc 93

SPIDER 2 WAY 90° - AISI 316

Material: AISI 316 steel Features: spider 2-way at 90° for the connection of 2 rotules to the load-bearing structure. Finish: polished steel.

38 Ø

5 5.

15 37 Ø

Ø19

Ø26

220

20 A-A 110

STRENGTH TEST IN ORTHOGONAL DIRECTION TO THE FACADE

STRENGTH TEST IN PARALLEL DIRECTION TO THE FACADE

Force (f) = 226.5 daN Value (f) detected in correspondence

Force (f) = 387.3 daN Value (f) detected in correspondence

of a movement of 1 mm

(1 daN corresponds to a weight of approx.1 kg)

Charge (daN) Carico (kN)

4 Charge (daN) Carico (kN)

BALUSTRADES ACCESSORIES FOR OUTDOORS

FACADES - SPIDER

(f )

2 2 1

Art. SP2203 94

0.5

1.5 2 2.5 Spostamento (mm) Displacement (mm)

Centre-to-centre 220 mm

3.5

Weight 1200 g

0.5

1 1.5 Spostamento (mm) Displacement (mm)

2.5

Q.ty 1 Pc

BALUSTRADES

FACADES - SPIDER SPIDER 1 WAY IN-LINE - AISI 316

ACCESSORIES FOR OUTDOORS

Material: AISI 316 steel Features: Spider 1-way in-line for the connection of a rotule to the load-bearing structure.Finish: polished steel.

A-A

Ø1

110

Ø2 6

Ø37

Ø38

26.5

STRENGTH TEST IN ORTHOGONAL DIRECTION TO THE FACADE

Force (f) = 554.3 daN Value (f) detected in correspondence of a movement of 1 mm - reference to one arm only. (1 daN corresponds to a weight of approx.1 kg)

10 9 8

Charge (daN) Carico (kN)

(f )

6 5 4 3 2 1 0

Art. SP2204

0.5

1.5 2 2.5 Spostamento (mm) Displacement (mm)

Centre-to-centre 110 mm

3.5

Weight 670 g

Q.ty 1 Pc 95

SPIDER 1 WAY 45° - AISI 316 Material: AISI 316 steel Features: spider 1-way at 45° for the connection of a rotule to the load-bearing structure. Finish: polished steel.

155.5

0 11

20 A-A

9 Ø1

Ø37

11 0

Ø2 6

Ø38

26.5

STRENGTH TEST IN ORTHOGONAL DIRECTION TO THE FACADE

Force (f) = 253 daN Value (f) detected in correspondence of a movement of 1 mm - reference to one arm only. (1 daN corresponds to a weight of approx.1 kg)

4 Charge (daN) Carico (kN)

BALUSTRADES ACCESSORIES FOR OUTDOORS

FACADES - SPIDER

(f )

Art. SP2205 96

0.5

1.5 2 Spostamento (mm) Displacement (mm)

Centre-to-centre 155.5 mm

2.5

3.5

Weight 770 g

Q.ty 1 Pc

BALUSTRADES

FACADES - SPIDER SPIDER 3 WAY - AISI 316

ACCESSORIES FOR OUTDOORS

Material: AISI 316 steel Features: spider 3-way for the connection of 3 rotules to the load-bearing structure. Finish: polished steel.

38 Ø 15 37 Ø

Ø26

15 5. 46

Ø19

220

38 Ø

5 15

110

Art. SP2206

Centre-to-centre 220 mm

Weight 1700 g

20 A-A

Q.ty 1 Pc

SPIDER 2 WAY FOR WALL ANCHORING AND ON GLASS-FIN - AISI 316

220

SP220L01

Ø38

15.5

Ø38

110

Ø12.5

12 A-A

29 .5 Ø12

110

Art. SP220L01 SP220L02

120

Ø12.5

12 A-A

110

120

Ø38

Material: AISI 316 steel Features: spider 2-way in-line for the connection of 2 rotules to the wall or to load-bearing ribs made of glass (glass-fin). Both right and left version - Finish: polished steel.

SP220L02

Dimensions Centre-to-centre 220 mm Centre-to-centre 220 mm

Description Left connection Right connection

Weight 1350 g 1350 g

Q.ty 1 Pc 1 Pc

SPIDER 1 WAY FOR WALL ANCHORING AND ON GLASS-FIN - AISI 316

120

2 Ø1 .5

12 A-A

110

Ø 12

2.5 Ø1

Ø 12

12 A-A

120

Material: AISI 316 steel Features: spider 1-way in-line for the connection of 1 rotule to the wall or to load-bearing ribs made of glass (glass-fin). Version both with slotted hole and circular hole - Finish: polished steel.

110

Ø38

15.5

BALUSTRADES ACCESSORIES FOR OUTDOORS

FACADES - SPIDER

SP220L03

Art. SP220L03 SP220L04 98

Dimensions Centre-to-centre 110 mm Centre-to-centre 110 mm

Ø2

SP220L04

Description Slotted hole Circular hole

Weight 1100 g 1100 g

Q.ty 1 Pc 1 Pc

BALUSTRADES

FACADES - SPIDER - ACCESSORIES SPIDER CONNECTOR - AISI 316

ACCESSORIES FOR OUTDOORS

Material: AVP - AISI 316 Features: spider spacer - connector, to be welded to the load-bearing structure Finish: polished steel

Ø36

M18x2,5

Ø53

Art. SP220Z

Dimensions Ø53 mm

Weight 1000 g

Q.ty 1 Pc

CONNECTION SCREW FOR SPIDER - AISI 316 Material: AISI 316 steel Features: connection screw for connecting the spider to the load-bearing structure without spacer. Ø36 mm with threaded pivot M18x2.5 mm length, pivot 46 mm. Finish: polished steel

Ø36

M18x2.5

Dimensions Ø36 mm thread M18x46 mm pitch 2.5 mm

Q.ty 1 Pc

ALUMINIUM RING NUTS Material: aluminium Features: ring nut for double-glazing, for rotule insertion Finish: matt aluminium

5,5

6,5 1,5

Art. SP220Z04

Art. SP60ALL12 SP60ALL15 SP60ALL16 SP60ALL20

Dimensions Ø external 60 mm Ø external 60 mm Ø external 60 mm Ø external 60 mm

Ø internal 46 mm Ø internal 46 mm Ø internal 46 mm Ø internal 46 mm

A 12 mm 15 mm 16 mm 20 mm

Q.ty 1 Pc 1 Pc 1 Pc 1 Pc 99

BALUSTRADES

FACADES - SPIDER - ACCESSORIES SILICONE GASKET

ACCESSORIES FOR OUTDOORS

Material: silicone Colour: transparent

3.2

7.2

16.2

8/12

Art. SP01

13.2

Dimensions 16.2 x 7.2 mm

Q.ty 1m

SILICONE GASKET Material: silicone Colour: transparent

12.2

23.2

15/20

12 18.4

Art. SP03

Dimensions 23.2 x 12.2 mm

Q.ty 1m

SILICONE GASKET Material: silicone Colour: transparent

12.5

26.6

18/23

15.3 21.7

Art. SP051 100

Dimensions 26.6 x 12.5 mm

Q.ty 1m

BALUSTRADES

FACADES - SPIDER - ACCESSORIES SILIRUB WS SILICONE SEALANT FOR STRUCTURAL GLAZING

ACCESSORIES FOR OUTDOORS

Description: SILIRUB WS is a high-quality neutral, highly elastic one-component silicone sealant. It has been developed for weather sealing of expansion joints in the building industry. Features: • Easy application • Resistant to UV rays • Stays elastic after curing • Good adhesion on many materials • Low modulus according to ISO standards • Resistant to UV rays, rain, frost, wind, and extreme temperatures. Application: • • • •

Joints sealing on structural glazing Ideal for expansion, perimeter and connection joints between various building materials Excellent adhesion on glass, laminated glass, painted aluminium, galvanised steel and brickwork It cannot be used as an adhesive for structural glass or double-glazing

Chemical base: Polysiloxane Consistency: solid paste Curing: in presence of moisture Skinning time: 10 min. (20°C/65% U.A.R) Curing time: 2 mm/24h (20°C/65%U.A.R) Temperature resistance: -60°C to + 180°C Elastic recovery: > 80 % Maximum distortion: 50 % (+/- 25%) Elasticity modulus 100%: 0.34 N/mm² (DIN 53504) Maximum tension: 1.36 N/mm² (DIN 53504) Elongation at break: > 900% (DIN 53504) SILIRUB WS

Art. SDNEU-WS

Format 600 ml

Hardness 25 ± 5 Shore A

Colour Black

Paintable No

Q.ty 1 Pc

GUN Professional gun for sealants in 600 ml bag

Art. SDAC-019

Format 600 ml

Q.ty 1 Pc 101