Shiv Chopra - Construction Documents by SHIV CHOPRA

SPACES DESIGN STUDIO SHIV CHOPRA

SDS

MASTERS PROJECT INTERIOR ARCHITECTURE DOCUMENTS

832 HILGARD AVENUE LOS ANGELES , CA - 90024 310- 866-7154

FINAL NOTEBOOK SPRING QUARTER , 2017

shivchopra@hotmail.com

CAL POLY POMONA/UCLA EXT MASTERS PROJECT INTERIOR ARCHITECTURE DOCUMENTS

MASTERS OF INTERIOR ARCHITECTURE PROGRAM CAL POLY POMONA / UCLA EXTENSION

SPRING QUARTER 2017

THE DESIGNS AND DRAWINGS ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS. THESE SHALL NOT BE USED, MODIFIED AND DUPLICATED

PROJECT NAME :

VEDA WELLNESS CENTER ( HOLISTIC WELLNESS CENTER )

IN WHOLE OR IN ANY PART

PROJECT NAME

PROJECT ADDRESS :

14547 TITUS STREET PANORAMA CITY , CA - 91402

VEDA WELLNESS CENTER HOLISTIC WELLNESS CENTER

PROJECT LOCATION

14547 TITUS STREET PANORAMA CITY, CA 91402

DATE

06 / 11 / 2017 SCALE

3 / 16" = 1' - 0" DRAWN BY

SHIV CHOPRA CHECKED BY

INSTRUCTOR : MR. LUIS DE MORAES, AIA - CCIDC, ENVIROTECHNO ARCHITECTURE SUBMITTED BY : SHIV CHOPRA

MR. LUIS DE MORAES SHEET TITLE

COVER PAGE SHEET NO.

CS - 00

FINISH SCHEDULE & DESIGNATIONS

PROJECT TEAM

VICINITY MAP

KEY PLAN SPACES DESIGN STUDIO

PREFIX FC

LOCATION FLOOR

WALLS

WALLS CEILING FLOOR

MILLWORK PARTITIONS COUNTER SPACES MILLWORK PARTITIONS COUNTER SPACES

DESIGNATION OF FINISH CONCRETE CERAMIC TILE GRANITE STONE PORCELAIN CARPET PEDIMAT CERAMIC TILE CONCRETE TILE BLOCK VINYL WALL-COVERING

PAINT

WOOD

WOOD STAIN

CLIENT/OWNER JAI DIXIT 2239 HOLLYWOOD BLVD. LOS ANGELES, CA 90028 T: 3102058172 F: 23281211

FOOD SERVICE CONSULTANT ISA VALE 5000 SOUTH ROSE STREET LOS ANGELES, CA 90020 T 213 571 9463 F 213 571 3748

ARCHITECT/DESIGNER SHIV CHOPRA 832 HILLGARD AVENUE,WESTWOOD LOS ANGELES, CA 90024 T 3108667154 F 310 216 0112

MECHANICAL ENGINEER SUMEDHA ANTONY 121 EAST UNION STREET PASADENA, CA 90084 T 626 663 1111 F 626 792 2222

ELECTRICAL ENGINEER JENNY HANDLER 332 SOUTH LA HOLLYWOOD AVENUE. LOS ANGELES, CA 90048 T 323 653 4121 F 323 653 5000

MILLWORK CONTRACTOR PETER SHERETON 121 HILGARD AVENUE, WESTWOOD LOS ANGELES, CA 90024 T 626 638 1555 F 626 792 0000

SHIV CHOPRA

SDS 832 HILGARD AVENUE LOS ANGELES , CA - 90024 310- 866-7154 shivchopra@hotmail.com

CAL POLY POMONA/UCLA EXT 14547 TITUS STREET, A WELL MAINTAINED 1961 VINTAGE COURTYARD OFFICE BUILDING.THE PROPERTY IS CENTRALLY LOCATED ON A QUIET STREET JUST OFF THE VIBRANT INTERSECTION OF VAN NUYS AND ROSCOE, ADJACENT TO THE WALMART ANCHORED PANORAMA MALL AND BLOCKS FROM THE PLANT RETAIL COMPLEX, WITH THE HIGHEST POPULATION DENSITY IN THE SAN FERNANDO VALLEY.

LIFE SAFETY CONSULTANT PAUL CHANDRA 33 WEST HOLLYWOOD LOS ANGELES, CA 90028 T 626 121 5363 F 626 121 6703

GENERAL CONTRACTOR TOMMY REGAL 310 WILSHIRE BLVD. LOS ANGELES, CA 90010 T 323 655 1211 F 323 607 8300

MS MW HD

WALLS COLUMNS EXPOSED STRUCTURE

PARTITIONS

STAINLESS STEEL BRUSHED STEEL POLISHED STEEL POWDER COATED OPAQUE GLASS TINTED GLASS TEMPERED GLAS

2. 3.

SHADED AREA - AREA PART OF THE CONTRACT THE DESIGNS AND DRAWINGS

ACTUAL HOURS

TRACKING HOURS PROJECTED HOURS

100% COMPLETE

PROJECT REQUIREMENT

75% COMPLETE

50% COMPLETE

25% COMPLETE

PROJECT REQUIREMENTS

PROJECT TIME ESTIMATED HOURS

COVER SHEET

MASTER LEGEND

MASTER SCHEDULES

CONSUTRUCTION PLAN

CONSTRUCTION PLAN

REFLECTED CEILING PLAN

POWER & COMMUNICATION PLAN

FLOOR&FINISH PLAN

COUNTER TOPS

WOOD BASE METAL BASE TILE BASE STONE BASE

FURNITURE PLAN

ENLARGED PLANS

INTERIOR ELEVATIONS

SECTIONAL DETAILS

GENERAL DETAILS

266

242

TOTAL HOURS

FURNITURE

FABRIC VINYL

HARD SURFACES COUNTER TOPS

STONE

PANELS CONNECTORS GLASS CONNECTORS

CLAMPS SPIDER CONNECTIONS POINT CONNECTIONS T-CLAD WALL CONNECTIONS

CEILINGS WALLS CABINETRY COUNTERS

HARDWIRED LIGHTING RECESSED DOWNLIGHT/WALL WASHER UNDER COUNTER STRIP LIGHTING COVE LIGHTING

CEILINGS WALLS

WALL SCONCES DECORATIVE PENDANTS

FLOOR WALL SURFACES MISCELLANEOUS

AND

POUND OR NUMBER

A.F.F.

ABOVE FINISHED FLOOR

APPROX.

APPROXIMATELY

GROUT

CS-02

GENERAL NOTES

CL.

CENTER LINE

PANELS PARTITIONS

CS-03

GENERAL NOTES

CLG.

CEILING

CS-04

A.D.A GUIDELINES

CTR.

CENTER

CS-05

INTERIOR FINISH AND FURNITURE SCHEDULE INTERIOR FINISH AND FURNITURE SCHEDULE

CLR.

CLEAR

DIA.

DIAMETER

DIM.

DIMENSION

DN.

DOWN

PASSAGE LATCH PRIVACY LOCK ENTRY LOCK/LATCH BOLT DECORATIVE PULLS/HANDLES

CS-06 CS-07

DOOR WINDOW SCHEDULE

ID DIVISION ID 1.0

CONSTRUCTION PLAN

EAST

ID 2.0

REFLECTED CEILING PLAN

EA.

EACH

ID 3.0

POWER AND COMMUNICATION PLAN

EQ.

EQUAL

ID 4.0

FLOOR AND FINISH PLAN

EXT.

EXTERIOR

ID 5.0

F.F. AND EQUIPMENT PLAN

FIN.

FINISH

ID 6.0

WASHROOM BLOW - UP

GYP. BD.

GYPSUM BOARD

ID 7.0

ELEVATOR BLOW - UP

INT.

INTERIOR

30,000 SQUARE FEET

ID 8.0

INTERIOR ELEVATIONS

MIN.

MINIMUM

ID 9.0

INTERIOR ELEVATIONS

MAX.

MAXIMUM

ID 10.0

RECEPTION AND FOOD KIOSK BLOWUP

NORTH

ID 11.0

SECTIONAL DETAILS

OPNG

OPENNING

ID 12.0

DETAILS

QTY.

QUANTITY

ID 13.0

DETAILS

REF.

REFERENCE

ID 14.0

DETAILS

U.O.N.

UNLESS OTHERWISE STATED

TYP.

TYPICAL

VEDA WELLNESS CENTER 14547 TITUS STREET PANORAMA CITY, CA 91402

YEAR BUILT

1961

BUILDING CLASS

PARCEL NO.

2210010031

GENERAL LAND USE.

COMMERCIAL

NO.OF FLOORS

CS DIVISION

SHEET INDEX AND MASTER LEGEND

HARDWARE

BUILDING SIZE

SHEET DESCRIPTION

DESCRIPTION

CS-01

PLASTIC LAMINATE

ADDRESS

SHEET #

ABBREVIATIONS

COVER PAGE

MILLWORK VERTICAL SURFACES

NAME

SHEET INDEX

CS-00

BRACKETS STAIR NOSING

TOTAL ESTIMATED HOURS TO COMPLETE PROJECT : 242 HOURS

THRESHOLD

SPRING QUARTER 2017

FLOOR TRANSITIONS

BUILDING DATA 1.

ARCHITECTURE DOCUMENTS

PROJECT TRACKING TRACKING HOURS

MASTERS PROJECT INTERIOR

ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS. THESE SHALL NOT BE USED, MODIFIED AND DUPLICATED IN WHOLE OR IN ANY PART

HOURS AVAILABLE TOTAL PROJECT HOURS AVAILABLE 205 HOURS

PROJECT NAME

ACTUAL HOURS REQUIRED VEDA WELLNESS CENTER TOTAL ACTUAL HOURS REQUIRED TO COMPLETE PROJECT : 266 HOURS

HOLISTIC WELLNESS CENTER

PROJECT LOCATION

LEGEND DESCRIPTION

14547 TITUS STREET

1 A a

DOOR NUMBER HARDWARE DOOR TYPE

A 1 a

WINDOW NUMBER HARDWARE WINDOW TYPE

NORTH ARROW

PANORAMA CITY, CA 91402

DOOR SYMBOL

DATE

06 / 11 / 2017

WINDOW SYMBOL SCALE

WALL TYPE

3 / 16" = 1' - 0" DRAWN BY

4 SIDE ELEVATION SHIV CHOPRA ELEVATION NO. SHEET NO.

SINGLE SIDE ELEVATION

DETAIL REFERENCE INDICATOR

CHECKED BY

MR. LUIS DE MORAES SHEET TITLE

GYP . BD PAINT 4 AFF 12'-5"

CEILING MATERIAL CEILING FINISH HEIGHT

CEILING SYMBOL

SHEET NO.

ITEM CODE

RT-10 3 ARTWORK

SHEET INDEX AND MASTER LEGEND

QUANTITY DESCRIPTION

FURNITURE SYMBOL

CS - 01

THE WORK DELINEATED IN THESE DRAWINGS AND DESCRIBED IIN THE SPECIFICATIONS SHALL CONFORM TO ALL CODES AND STANDARDS THAT HAVE JURISDICTION. INSTALLATION OF MATERIALS SHALL FOLLOW THE MANUFACTURER'S PUBLISHED SPECIFICATIONS OR ACCEPTED TRADE STANDARDS IN ADDITION TO MEETING OR EXCEEDING THE INDICATED DESIGN STANDARDS. ALL REQUIREMENTS AND REFUTATIONS PERTAINING TO THE HANDICAPPED AND OSHA MUST BE INCORPORATED IN THE WORK EVEN THOUGH THEY MAY NOT BE LISTED INDIVIDUALLY AND SEPARATELY IN EITHER THE DRAWINGS OR SPECIFICATIONS. THESE GENERAL NOTES SHALL APPLY TO ALL DRAWINGS AND GOVERN UNLESS OTHERWISE NOTED OR SPECIFIED. NO INFORMATION OR DETAILS ON THE DRAWINGS OF THIS PROJECT MAY BE USED WITHOUT THE WRITTEN PERMISSION FROM THE DESIGNER. DO NOT SCALE DRAWINGS. CONTRACTOR SHALL FIELD VERIFY ALL DIMENSIONS AND EXISTING SITE CONDITIONS IF DISCREPANCIES ARE FOUND CONTRACTOR SHALL NOTIFY THE ARCHITECT IMMEDIATELY.

ALL PAINTED MILLWORK BASE TRIM AND DOORS TO BE SHOP PRIMED FOR THE APPROPRIATE PAINT TYPE AND FINISH PAINTED

CONTRACTOR SHALL PROVIDE A PORTABLE FIRE EXTINGUISHER WITH A RATING OF NOT LESS THAN 24 DURING CONSTRUCTION. MAXIMUM TRAVEL DISTANCE TO THE EXTINGUISHER = 75'-O”. ORIVUDE ADDITIONAL EXTINGUISHERS AS REQUIRED BY AREA OF

SAFETY MEASURES: CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING ALL SAFETY MEASURES NECESSARY TO INSURE THE SAFETY OF THE PUBLIC AS WELL AS ALL EMPLOYEES AND SUB-CONTRACTORS. CONSTRUCTION SHALL NOT OBSTRUCT ANY REQUIRED EXIT PASSAGEWAY. CONTRACTOR SHALL REFER TO GENERAL NOTES AS DESCRIBED ON EACH DRAWING SHEET AND INCORPORATE AS PART OF THIS SCOPE OF WORK. THE GENERAL CONTRACTOR SHALL PERSONALLY INSPECT THE SITE OF THE PROPOSED WORK TO ARRIVE AT A CLEAR UNDERSTANDING OF THE CONDITIONS UNDER WHICH THE WORK IS TO BE DONE. HE SHALL BE HELD TO HAVE COMPARED THE PREMISES AND SITE WITH THE DOCUMENTS AND TO HAVE SATISFIED HIMSELF AS TO THE CONDITIONS OF THE PREMISES. EXISTING CONDITIONS AFFECTING THE EXECUTION OF THE WORK AND ALL DISCREPANCIES SHALL BE REPORTED TO THE ARCHITECT PRIOR TO THE SUBMITTAL OF HIS PROPOSAL. NO EXTRA CONSIDERATION WILL BE ALLOWED BY REASON OF ERROR OR OVERSIGHT ON THE PART OF THE CONTRACTOR OR ON ACCOUNT OF INTERFERENCE BY EITHER OWNER OR OTHER CONTRACTOR'S ACTIVITIES.

CONTRACTOR, AS AGENT FOR THE OWNER, SHALL COORDINATE ALL UTILITY SERVICE INSTALLATIONS, EXCEPT TELEPHONE, WITH THE OWNER AND UTILITY COMPANIES.

THE STRUCTURAL, MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS ARE SUPPLEMENTARY TO THE ARCHITECTURAL DRAWINGS. SHOULD THERE BE ANY DISCREPANCIES BETWEEN THE DRAWINGS AND/OR SPECIFICATIONS, THE CONTRACTOR SHALL NOTIFY THE DESIGNER IMMEDIATELY FOR CLARIFICATION. THE CONTRACTOR, AT THE CONTRACTOR'S EXPENSE, SHALL CORRECT WORK INSTALLED IN CONFLICT WITH THESE DRAWINGS. THE DIVISION OF DRAWINGS INTO SEPARATE CATEGORIES (ARCHITECTURAL, STRUCTURAL, ETC.) IS FOR CONVENIENCE ONLY, AND SHALL NOT BE CONSTRUED AS DIVIDING THE WORK BY TRADE OR SUB-CONTRACT.

AT PROJECT START AND AGAIN AT TURNOVER, CONTRACTOR WILL SUPPLY TO OWNER TWO COPIES OF A CURRENT SUBCONTRACTOR LIST. SUCH A LIST SHALL INCLUDE SUBCONTRACTOR NAME, ADDRESS, WORK PERFORMED, CONTACT NAME, TELEPHONE, FAX AND PAGER NUMBERS.

IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO MAKE EXACT DETERMINATIONS AS TO THE LOCATION OF ALL EXISTING UTILITIES. CONTRACTOR SHALL NOT BEGIN WORK UNTIL THIS DETERMINATION HAS BEEN MADE. CONTRACTOR AGREES TO BE FULLY RESPONSIBLE FOR ANY AND ALL DAMAGE THAT MIGHT BE OCCASIONED BY HIS FAILURE TO EXACTLY LOCATE AND PRESERVE EXISTING UTILITIES.

ENTRANCE AND EXITS

FACILITIES SHALL BE MADE ACCESSIBLE TO PERSONS WITH DISABILITIES. REVOLVING DOORS SHALL NOT BE USED AS A REQUIRED ENTRANCE FOR PERSONS WITH

DISABILITIES. DURING PERIODS OF PARTIAL OR RESTRICTED USE OF A BUILDING OR FACILITY, THE ENTRANCES USED FOR PRIMARY ACCESS SHALL BE ACCESSIBLE TO AND USABLE BY PERSONS WITH DISABILITIES. EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL KNOWLEDGE OR EFFORT. MANUALLY OPERATED EDGE OR SURFACE-MOUNTED FLUSH BOLTS AND SURFACE BOLTS ARE PROHIBITED. WHEN EXIT DOORS ARE USED IN PAIRS AND APPROVED AUTOMATIC FLUSH BOLTS ARE USED, THE DOOR LEAF HAVING THE AUTOMATIC FLUSH BOLTS SHALL HAVE NO DOORKNOB OR SURFACE-MOUNTED HARDWARE. THE UNLATCHING OF ANY LEAF SHALL NOT REQUIRE MORE THAN ONE OPERATION. LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND WHICH ARE IN A PATH OF TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE HARDWARE, PANIC BARS, PUSH-PULL ACTIVATING BARS, OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP THE OPENING HARDWARE. LOCKED EXIT DOORS SHALL OPERATE AS ABOVE IN EGRESS DIRECTION.

44” ABOVE THE FLOOR. EVERY DOORWAY WHICH IS LOCATED WITHIN AN ACCESSIBLE PATH OF TRAVEL SHALL BE OF A SIZE AS TO PERMIT THE INSTALLATION OF A DOOR NOT LESS THAN 3' IN WIDTH AND NOT LESS THAN 6'-8” IN HEIGHT. WHEN INSTALLED, EXIT DOORS SHALL BE CAPABLE OF OPENING SO THAT THE CLEAR WIDTH OF THE EXIT IS NOT LESS THAN 32”, MEASURED BETWEEN THE FACE OF THE DOOR AND OPPOSITE STOP. WHERE A PAIR OF DOORS IS UTILIZED, AT LEAST ONE OF THE DOORS SHALL PROVIDE A CLEAR, UNOBSTRUCTED OPENING WIDTH OF 32” WITH THE LEAF POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. WHEN AN AUTOMATIC DOOR OPERATOR IS UTILIZED TO OPERATE A PAIR OF DOORS, AT LEAST

CLEAN ALL SOILED AND DISCOLORED SURFACES WITHIN THE AREA OF CONSTRUCTION AFTER INSTALLATION.

HANDRAIL FOR EACH 88” OF REQUIRED WIDTH. INTERMEDIATE HANDRAILS SHALL BE

EACH SEX ALSO. WHERE UNISEX FACILITIES ARE PROVIDED FOR

SPACED APPROXIMATELY EQUALLY ACROSS THE ENTIRE WIDTH OF THE STAIRWAY.

NON-HANDICAPPED/NON-DISABLED PERSONS, SUCH UNISEX FACILITIES CAN BE PROVIDED FOR PERSONS WITH DISABILITIES.

HANDRAILS SHALL BE 34” TO 38” ABOVE THE NOSING OF THE TREADS. HANDRAILS SHALL EXTEND A MINIMUM OF 12” BEYOND THE TOP NOSING AND 12” PLUS THE

WHERE THE EXTENSION OF THE HANDRAIL IN THE DIRECTION OF THE STAIR RUN WOULD CREATE A HAZARD, THE TERMINATION OF THE EXTENSION SHALL BE MADE EITHER ROUNDED

FOR HINGED DOORS, THE OPENING WIDTH SHALL BE MEASURED WITH THE DOOR POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. MINIMUM MANEUVERING CLEARANCES AT DOORS SHALL BE AS SHOWN IN FIGURE 11B-26. THE FLOOR OR GROUND AREA WITHIN THE REQUIRED CLEARANCES SHALL BE LEVEL AND CLEAR. THERE SHALL BE A LEVEL AND CLEAR FLOOR OR LANDING ON EACH SIDE OF A DOOR. THE LEVEL AREA SHALL HAVE A LENGTH IN THE DIRECTION OF DOOR SWING OF AT LEAST 60” AND THE LENGTH OPPOSITE THE DIRECTION OF DOOR SWING OF 48” AS MEASURED AT RIGHT ANGLES TO THE PLANE OF THE DOOR IN THE CLOSED POSITION. THE WIDTH OF THE LEVEL AREA ON THE SIDE TO WHICH THE DOOR SWINGS SHALL EXTEND A OF 18” PAST THE STRIKE EDGE FOR INTERIOR DOORS.

WHERE TOWEL SANITARY NAPKINS, WASTE RECEPTACLES, AND OTHER SIMILAR

ENDS SHALL BE RETURNED OR TERMINATE IN NEWEL POSTS OR SAFETY TERMINALS.

DIAMETER, WITH A ¼” THICK TRIANGLE SUPERIMPOSED ON THE CIRCLE AND WITHIN THE 12” DIAMETER.

WITHIN 40” FROM THE FINISHED FLOOR.

1-/2” IN CROSS SECTIONAL DIMENSION OR THE SHAPE SHALL PROVIDE AN EQUIVALENT

GEOMETRIC (CIRCLE & TRIANGLE) SYMBOLS ON SANITARY FACILITY DOORS SHALL BE CENTERED ON THE DOOR AT A HEIGHT OF 60” AND THEIR COLOR AND CONTRAST

GRIPPING SURFACE. THE HANDGRIP PORTION OF HANDRAILS SHALL HAVE A SMOOTH

SHALL BE DISTINCTLY DIFFERENT FROM THE COLOR AND CONTRAST OF THE DOOR.

HANDRAIL SHALL BE FREE OF SHARP OR ABRASIVE ELEMENTS. EDGES SHALL HAVE A

FLOOR, WITHIN THE SANITARY FACILITY ROOM, OF SUFFICIENT SIZE TO INSCRIBE

SUCH AS PORTLAND CEMENT, CONCRETE, CERAMIC TILE OR OTHER APPROVED MATERIAL WHICH EXTEND UPWARD ONTO THE WALLS AT LEAST 5”. WALLS WITHIN

PARALLEL TO AND NOT MORE THAN 1” FROM THE NOSE OF THE STEP OR LANDING TO ALERT THE VISUALLY IMPAIRED. THE STRIP SHALL BE OF MATERIAL THAT IS AT LEAST AS SLIP

WATER CLOSET COMPARTMENTS AND WALLS WITHIN 24” OF THE FRONT AND

THAN THE DOOR TO THE ACCESSIBLE TOILET COMPARTMENT IN ANY POSITION MY

SIDES OF URINALS SHALL BE SIMILARLY FINISHED TO A HEIGHT OF 48” AND,

ENCROACH INTO THIS SPACE BY NOT MORE THAN 12”

EXCEPT FOR STRUCTURAL ELEMENTS, THE MATERIALS USED IN SUCH WALLS SHALL BE A TYPE WHICH IS NOT ADVERSELY AFFECTED BY MOISTURE.

A WATER CLOSET FIXTURE LOCATED IN A COMPARTMENT SHALL PROVIDE A

RESISTANT AS THE OTHER TREADS OF THE STAIR. WHERE STAIRWAYS OCCUR OUTSIDE A BUILDING, THE UPPER APPROACH AND ALL TREADS SHALL BE MARKED BY A STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2” AND NOT

THE WATER CLOSET SHALL PROVIDE 18” FROM THE CENTERLINE OF THE WATER

SPACE FROM A WALL AT ONE SIDE OF THE WATER CLOSET. THE OTHER SIDE OF

GRAB BARS SHALL BE LOCATED ON EACH SIDE, OR ON ONE SIDE AND THE BACK

THESE CLEAR SPACES.

OF THE ACCESSIBLE TOILET STALL OR COMPARTMENT.

A MINIMUM 48” LONG CLEAR SPACE SHALL BE PROVIDED IN FRONT OF THE WATER

GRAB BARS AT THE SIDE SHALL BE AT LEAST 42” LONG WITH THE FRONT END POSITIONED 24” IN FRONT OF THE WATER CLOSET STOOL AND WITH THE BACK

STRIP SHALL BE ACCEPTABLE.

CLOSET IF THE COMPARTMENT HAS AN END OPENING DOOR (FACING THE WATER

END POSITIONED NO MORE THAN 12” FROM THE REAR WALL. GRAB BARS AT THE

CLOSET) AND A MINIMUM 60” LONG CLEAR SPACE SHALL BE PROVIDED IN FRONT

BACK SHALL BE NOT LESS THAN 36” LONG.

ALL TREAD SURFACES SHALL BE SLIP-RESISTANT. TREADS SHALL HAVE SMOOTH, ROUNDED,

OF THE WATER CLOSET IF THE COMPARTMENT HAS A DOOR LOCATED AT THE

MORE THAN 4” WIDE PLACED PARALLEL TO AND NOT MORE THAN 1” FROM THE NOSE OF THE STEP OR LANDING TO ALERT THE VISUALLY IMPAIRED. THE STRIP SHALL BE OF MATERIAL THAT IS AT LEAST AS SLIP-RESISTANT AS THE OTHER TREADS OF THE STAIR. A PAINTED

SIDE. GRAB BARS SHALL NOT PROJECT MORE THAN 3” INTO THESE CLEAR

GRAB BARS SHALL BE SECURELY ATTACHED 33” ABOVE AND PARALLEL TO THE

EDGE).

SPACES.

FLOOR, EXCEPT THAT WHERE A TANK-TYPE TOILET IS USED WHICH OBSTRUCTS PLACEMENT AT 33”, THE GRAB BAR MAY BE AS HIGH AS 36”.

THE NOSING SHALL NOT PROJECT MORE THAN 1-1/2” PAST THE FACE OF THE RISER BELOW.

WATER CLOSET COMPARTMENTS SHALL BE EQUIPPED WITH A DOOR THAT HAS AN AUTOMATIC-CLOSING DEVICE, AND SHALL HAVE A CLEAR, UNOBSTRUCTED

THE DIAMETER OR WIDTH OF THE GRIPPING SURFACES OF A GRAB BAR SHALL BE

OPEN RISERS ARE NOT PERMITTED.

OPENING WIDTH OF 32” WHEN LOCATED AT THE END AND 34” WHEN LOCATED AT

1-1/4” TO 1-1/2” OR THE SHAPE SHALL PROVIDE AN EQUIVALENT GRIPPING

THE SIDE WITH THE DOOR POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS

BETWEEN THE WALL AND THE GRAB BARS SHALL BE 1-1/2”/

APPROVED STAIRWAY IDENTIFICATION SIGNS SHALL BE LOCATED AT EACH FLOOR LEVEL IN

CLOSED POSITION.

OR CHAMFERED EXPOSED EDGES, AND NO ABRUPT EDGES AT THE NOSING (LOWER FRONT

ALL ENCLOSED STAIRWAYS IN BUILDINGS FOUR OR MORE STORIES IN HEIGHT, TWO OR

THE STRUCTURAL STRENGTH OF GRAB BARS, TUB AND SHOWER SEATS,

MORE STORIES IN HEIGHT FOR DSA/AC REQUIREMENTS. THE SIGN SHALL IDENTIFY THE

WHEN STANDARD COMPARTMENT DOORS ARE USED, WITH A MINIMUM

FASTENERS, AND MOUNTING DEVICES SHALL MEET THE FOLLOWING

STAIRWAY, INDICATE WHETHER THERE IS ROOF ACCESS, THE FLOOR LEVEL, AND THE UPPER AND LOWER TERMINUS OF THE STAIRWAY. THE SIGN SHALL BE LOCATED APPROXIMATELY 5'

9” CLEARANCE FOR FOOTRESTS UNDERNEATH AND A SELF-CLOSING DEVICE,

SPECIFICATIONS:

CLEARANCE AT THE STRIKE EDGE AS SPECIFIED IN SECTION 1004.9.2.2 IS NOT

ABOVE THE FLOOR LANDING IN A POSITION WHICH IS READILY VISIBLE WHEN THE DOOR IS IN THE OPEN OR CLOSED POSITION OR AS REQUIRED BY THE DSA/AC THE SIGN SHALL BE LOCATED APPROXIMATELY 5' ABOVE THE FLOOR LANDING IMMEDIATELY ADJACENT TO THE DOOR ON THE STIKE SIDE. SIGNS SHALL COMPLY WITH THE REQUIREMENTS OF UBC STD. NO. 10-2.

REQUIRED. THE INSIDE AND OUTSIDE OF THE COMPARTMENT DOOR SHALL BE EQUIPPED WITH A LOOP OR U-SHAPED HANDLE IMMEDIATELY BELOW THE LATCH. THE LATCH SHALL BE FLIP-OVER STYLE, SLIDING, OR OTHER HARDWARE NOT REQUIRING THE

USER TO GRASP OR TWIST. CORRIDORS & AISLES EVERY CORRIDOR SERVING AN OCCUPANT LOAD OF 10 OR MORE SHALL NOT BE LESS THAN 44” IN WIDTH. CORRIDORS SERVING AN OCCUPANT LOAD OF LESS THAN 10 SHALL NOT BE LESS THAN 36” IN WIDTH.

EXCEPT FOR DOOR OPENING WIDTHS AND DOOR SWINGS, A CLEAR, UNOBSTRUCTED ACCESS NOT LESS THAN 44” SHALL BE PROVIDED TO WATER CLOSET COMPARTMENTS DESIGNED FOR USE BY PERSONS WITH DISABILITIES AND THE SPACE IMMEDIATELY IN FRONT OF A WATER CLOSET COMPARTMENT SHALL BE NOT LESS THAN 48” AS MEASURED AT A RIGHT ANGLE TO COMPARTMENT DOOR IN ITS CLOSED POSITION.

CORRIDORS WHICH ARE LOCATED ON AN ACCESSIBLE ROUTE AND EXCEED 200' IN LENGTH SHALL HAVE A MINIMUM CLEAR WIDTH OF 60”; HAVE, AT A CENTRAL LOCATION, A 60” BY 60” MINIMUM WHEELCHAIR TURNING SPACE OR PASSING ALCOVE; HAVE, AT A CENTRAL

SANITARY FACILITY FIXTURES & ACCESSORIES

LOCATION, AN INTERVENING CROSS OR TEE CORRIDOR, A MINIMUM OF 48” IN WIDTH; OR, HAVE, AT A CENTRAL LOCATION, AN OPENABLE DOOR.

THE HEIGHT OF ACCESSIBLE WATER CLOSETS SHALL BE A MINIMUM OF 17” AND A

CIRCULATION AISLES AND PEDESTRIAN WAYS SHALL BE SIZED ACCORDING TO FUNCTIONAL

EXCEPT THAT 3” SEATS SHALL BE PERMITTED ONLY IN ALTERATIONS WHERE THE EXISTING FIXTURE IS LESS THAN 15” HIGH.

REQUIREMENTS AND IN NO CASE SHALL BE LESS THAN 36” IN CLEAR WIDTH.

MAXIMUM OF 19” MEASURED TO THE TOP OF A MAXIMUM 2” HIGH TOILET SEAT,

UNDERNEATH THE LAVATORY.

THAN A REQUIRED EXIT STAIRWAY, SHALL PROVIDE A MINIMUM OF 48” OF CLEAR SPACE FROM

ELEVATORS, OR SPECIAL ACCESS LIFTS.

TO ALLOW A FORWARD APPROACH. SUCH CLEAR FLOOR SPACE SHALL ADJOIN OR

LAVATORIES ADJACENT TO A WALL SHALL BE MOUNTED WITH A MINIMUM

ANY DOOR OPENING INTO SUCH VESTIBULE WHEN THE DOOR IS POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. DOORS IN A SERIES SHALL SWING EITHER IN THE

GROUND AND FLOOR SURFACES ALONG THE ACCESSIBLE ROUTES AND IN

SAME DIRECTION OR AWAY FROM THE SPACE BETWEEN THE DOORS.

ACCESSIBLE ROOMS AND SPACES, INCLUDING FLOORS, WALKS, RAMPS, STAIRS, AND

DISTANCE OF 18” TO THE CENTER LINE OF THE FIXTURE.

LAVATORIES SHALL BE MOUNTED WITH THE RIM OR COUNTER SURFACE NO HIGHER THAN 34” ABOVE THE FINISHED FLOOR AND WITH A CLEARANCE OF AT LEAST 29” FROM THE FLOOR TO THE BOTTOM OF THE APRON WITH KNEE

DOORS ARE USED, A 10” HIGH SMOOTH PANEL SHALL BE INSTALLED ON THE PUSH SIDE OF

CHANGES IN A LEVEL BETWEEN ¼” AND ½” SHALL BE ACCOMPLISHED BY MEANS OF A

CLEARANCE UNDER THE FRONT LIP EXTENDING A MINIMUM OF 30” IN WIDTH AND

THE DOOR, WHICH WILL ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OF HAZARDOUS CONDITION.

RAMP NO STEEPER THAN 1 VERTICAL TO 2 HORIZONTAL.

8” MINIMUM DEPTH AT THE TOP. TOE CLEARANCE SHALL BE THE SAME WIDTH AND SHALL BE A MINIMUM OF 9” HIGH FROM THE FLOOR AND A MINIMUM OF 17” DEEP

IF CARPET OR CARPET TILE IS USED IN A GROUND OR FLOOR SURFACE, IT SHALL BE

FROM THE FRONT OF THE LAVATORY.

SECURELY ATTACHED; HAVE A FIRM CUSHION, PAD OR BACKING OR NO CUSHION OR PAD; AND HAVE A LEVEL LOOP, TEXTURED LOOP, LEVEL CUT PILE, OR LEVEL

HOT WATER AND DRAIN PIPES ACCESSIBLE UNDER LAVATORIES SHALL BE

CUT/UNCUT PILE TEXTURE. THE MAXIMUM PILE HEIGHT SHALL BE ½”. EXPOSED

INSULATED OR OTHERWISE COVERED. THERE SHALL BE NO SHARP OR ABRASIVE SURFACES UNDER LAVATORIES

ALL MATERIALS MUST MEET FLAME SPREADS OF LESS THAN 25 (UNSPRINKLED AREAS ABOVE CEILING), 200 (SPRINKLED ARES).

MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 8-1/2 POUNDS FOR EXTERIOR

EDGES OF CARPET SHALL BE FASTENED TO FLOOR SURFACES AND HAVE TRIM ALONG

DOORS AND 5 POUNDS FOR INTERIOR DOORS, SUCH PULL OR PUSH EFFORT BEING APPLIED

THE ENTIRE LENGTH OF THE EXPOSED EDGE. CARPET EDGE TRIM SHALL COMPLY

AT RIGHT ANGLES TO HINGED DOORS AND AT THE CENTER PLANE OF SLIDING OR FOLDING

WITH SECTION 1124B.2.

WHERE URINALS ARE PROVIDED, AT LEAST ONE SHALL HAVE A CLEAR FLOOR SPACE 30” BY 48” IN FRONT OF THE URINAL TO ALLOW FORWARD APPROACH.

DOORS. COMPENSATING DEVICES OR AUTOMATIC DOOR OPERATORS MAY BE UTILIZED TO MEET THE ABOVE STANDARDS. WHEN FIRE DOORS ARE REQUIRED, THE MAXIMUM EFFORT TO SANITARY FACILITIES (GENERAL)

WHERE ONE OR MORE URINALS ARE PROVIDED, AT LEAST ONE WITH A RIM PROJECTING A MINIMUM OF 14” FROM THE WALL AND AT A MAXIMUM OF 17” ABOVE

APPROPRIATE ADMINISTRATIVE AUTHORITY, NOT TO EXCEED 15 POUNDS. SANITARY FACILITIES THAT SERVE BUILDINGS, FACILITIES OR PORTIONS OF BUILDINGS

THE FLOOR SHALL BE PROVIDED.

OR FACILITIES THAT ARE REQUIRED TO BE ACCESSIBLE TO PERSONS WITH DISABILITIES ARE REQUIRED TO BE ACCESSIBLE.

THE DESIGNS AND DRAWINGS ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS. THESE SHALL NOT BE USED, MODIFIED AND DUPLICATED IN WHOLE OR IN ANY PART

PROJECT NAME

VEDA WELLNESS CENTER HOLISTIC WELLNESS CENTER

MOMENT FROM THE APPLICATION OF A 250-LB POINT LOAD SHALL BE LESS THAN THE ALLOWABLE STRESS FOR THE MATERIAL OF THE GRAB BAR OR SEAT.

PROJECT LOCATION

SHEAR STRESS INDUCED IN A GRAB BAR OR SEAT BY THE APPLICATION OF A THE MATERIAL OF THE GRAB BAR OR SEAT, AND ITS MOUNTING BRACKET OR

14547 TITUS STREET

OTHER SUPPORT IS CONSIDERED TO BE FULLY RESTRAINED, THEN DIRECT AND TORSIONAL SHEAR STRESSES SHALL NOT EXCEED THE ALLOWABLE SHEAR

PANORAMA CITY, CA 91402

STRESS. SHEAR FORCE INDUCED IN FASTENER OR MOUNTING DEVICES FROM THE APPLICATION OF A 250-LB POINT LOAD SHALL BE LESS THAN THE ALLOWABLE

DATE

LATERAL LOAD OF EITHER THE FASTENER OR MOUNTING DEVICE OR THE SUPPORTING STRUCTURE, WHICHEVER HAS THE SMALLER ALLOWABLE LOAD. TENSILE FORCE INDUCED IN A FASTENER BY A DIRECT TENSION FORCE OF A

06 / 11 / 2017

250-LB POINT LOAD, PLUS THE MAXIMUM MOMENT FROM THE APPLICATION OF A 250-LB POINT LOAD, SHALL BE LESS THAN THE ALLOWABLE WITHDRAWAL LOAD BETWEEN THE FASTENER AND SUPPORTING STRUCTURE.

SCALE

GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.

3 / 16" = 1' - 0"

A GRAB BAR AND ANY WALL OR OTHER SURFACE ADJACENT TO IT SHALL BE FREE OF ANY SHARP OR ABRASIVE ELEMENTS. EDGES SHALL HAVE A MINIMUM RADIUS OF 1/8”.

DRAWN BY

SPACE ALLOWANCE & REACH RANGES

SHIV CHOPRA

THE MINIMUM CLEAR FLOOR OR GROUND SPACE REQUIRED TO ACCOMMODATE A SINGLE, STATIONARY WHEELCHAIR AND OCCUPANT IS 30” BY 48”. (THE MINIMUM

CURB RAMPS, SHALL BE STABLE, FIRM AND SLIP-RESISTANT. CHANGES IN LEVEL UP TO ¼” MAY BE VERTICAL AND WITHOUT EDGE TREATMENT.

SPRING QUARTER 2017

BENDING STRESS IN A GRAB BAR OR SEAT INDUCED BY THE MAXIMUM BENDING

250-LB POINT LOAD SHALL BE LESS THAN THE ALLOWABLE SHEAR STRESS FOR

THROUGHOUT, OR SHALL BE CONNECTED BY PEDESTRIAN RAMPS, PASSENGER

OPERATE THE DOOR MAY BE INCREASED TO THE MAXIMUM ALLOWABLE BY THE

GRAB BARS

CLOSET TO THE WALL. GRAB BARS SHALL NOT PROJECT MORE THAN 3” INTO

WHEELCHAIR TRAFFIC.

CONTRACTOR TO PROTECT ALL MILLWORK DURING CONSTRUCTION.

SIZE, SHALL BE PROVIDED FOR WHEELCHAIR MANEUVERING. DOORS OTHER

MINIMUM 28” WIDE CLEAR SPACE FROM A FIXTURE OR A MINIMUM 32” WIDE CLEAR

FREE.

CONTRACTOR TO COORDINATE ALL MILLWORK INSTALLATIONS WITH MILLWORK CONTRACTOR.

ARCHITECTURE DOCUMENTS

TOILET ROOM FLOORS SHALL HAVE A SMOOTH, HARD, NON-ABSORBENT SURFACE

STRIP OF CLEARLY CONTRASTING COLOR AT LEAST 2” AND NOT MORE THAN 4” WIDE PLACED

CAL POLY POMONA/UCLA EXT MASTERS PROJECT INTERIOR

A CLEAR SPACE MEASURED FROM THE FLOOR TO A HEIGHT OF 23” ABOVE THE

THE UPPER APPROACH AND THE LOWER TREAD OF EACH STAIR SHALL BE MARKED BY A

shivchopra@hotmail.com

DISPENSERS THAT CONTROL DELIVERY OR THAT DO NOT PERMIT CONTINUOUS

HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1-1/2” BETWEEN THE WALL

THE SPACE BETWEEN TWO CONSECUTIVE DOOR OPENINGS IN A VESTIBULE, SERVING OTHER

RECESSED DOORMATS SHALL BE ADEQUATELY ANCHORED TO PREVENT INTERFERENCE WITH

TOILET TISSUE DISPENSERS SHALL BE LOCATED ON THE WALL WITHIN 12” OF THE FRONT EDGE OF THE TOILET SEAT AND NO LOWER THAN 19” FROM THE FLOOR. PAPER FLOW SHALL NOT BE USED.

A CIRCLE WITH A DIAMETER NOT LESS THAN 60”, OR A CLEAR SPACE 56” BY 63” IN

310- 866-7154

TYPE SHALL BE LOCATED WITH ALL OPERABLE PARTS, INCLUDING COIN SLOTS,

MULTIPLE ACCOMMODATION SANITARY FACILITIES

MAXIMUM OF 3” DEEP AND EXTENDS AT LEAST 18” ABOVE THE TOP OF THE RAIL.

LOS ANGELES , CA - 90024

DISPENSING AND DISPOSAL FIXTURES ARE PROVIDED, AT LEAST ONE OF EACH

MINIMUM RADIUS OF 1/8”.

AND THE HANDRAIL. HANDRAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS A

832 HILGARD AVENUE

40” FROM THE FLOOR.

UNISEX SANITARY FACILITIES SHALL BE IDENTIFIED BY A CIRCLE ¼” THICK, 12” IN

FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION. WHERE NARROW FRAME

ALL MATERIALS USED WITHIN THIS PROJECT SHALL BE ASBESTOS

MIRRORS SHALL BE MOUNTED WITH THE BOTTOM EDGE NO HIGHER THAN

IN BUILDINGS AND FACILITIES, FLOORS OF A GIVEN STORY SHALL BE A COMMON LEVEL

UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR

ALL FINISHES SHALL BE PER SAMPLES SUBMITTED TO THE LANDLORD FOR REVIEW AND APPROVAL. ABSOLUTELY NO SUBSTITUTIONS WILL BE PERMITTED WITHOUT PRIOR WRITTEN APPROVAL FROM THE LANDLORD.

UPWARD. WOMEN'S SANITARY FACILITIES SHALL BE IDENTIFIED BY A CIRCLE ¼” THICK AND 12” IN DIAMETER.

OVERLAP AN ACCESSIBLE ROUTE AND SHALL EXTEND INTO KNEE AND TOE SPACE

DEBRIS.

CONTROLS, AND FAUCET AND OPERATING MECHANISM CONTROLS, SHALL BE NO

EQUILATERAL TRIANGLE ¼” THICK WITH EDGES 12” LONG AND A VERTEX POINTING

SURFACE WITH NO SHARP CORNERS. ANY WALL OR OTHER SURFACE ADJACENT TO THE

SDS

THE FORCE REQUIRED TO ACTIVATE WATER CLOSET AND URINAL FLUSH VALVE

NEED NOT EXTEND OUT INTO THE LANDING.

DOORWAY.

THE BOTTOM 10” OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING SHALL HAVE A SMOOTH,

SHALL BE MOUNTED NO MORE THAN 44” ABOVE THE FLOOR.

SELF-CLOSING FAUCET CONTROL VALVES ARE ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10 SECONDS.

A CLEAR FLOOR SPACE 30” BY 48” SHALL BE PROVIDED IN FRONT OF A LAVATORY

REMOVE ALL CONSTRUCTION DEBRIS AS THE WORK PROGRESSES. CONTRACTOR SHALL USE APPROVED ROUTE FOR REMOVING

NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST, AND

DOORWAYS LEADING TO MEN'S SANITARY FACILITIES SHALL BE IDENTIFIED BY AN

CONTINUOUS FROM LANDING TO LANDING, THE INNER RAIL SHALL BE CONTINUOUS AND

SHIV CHOPRA

OPERATING MECHANISM CONTROLS, SHALL BE OPERABLE WITH ONE HAND, SHALL

GREATER THAN 5 LB.

FLOORS & LEVELS

THE FLOOR OR LANDING SHALL BE NOT MORE THAN ½” LOWER THAN THE THRESHOLD OF THE

WATER CLOSET AND URINAL FLUSH VALVE CONTROLS, AND FAUCET AND

WHERE FACILITIES ARE TO BE USED SOLELY BY SMALL CHILDREN, THE SPECIFIC HEIGHTS MAY BE ADJUSTED TO MEET THEIR ACCESSIBILITY NEEDS.

ONE OF THE DOORS SHALL PROVIDE A CLEAR, UNOBSTRUCTED OPENING WIDTH OF 32” WITH

MINIMUM OF 24” PAST THE STRIKE EDGE OF THE DOOR FOR EXTERIOR DOORS AND A MINIMUM ? = “PLUS OR MINUS”. WHEN THIS SYMBOL IS ADJACENT TO A GIVEN DIMENSION, IT INDICATES THAT THE ACTUAL DIMENSION MAY VARY SLIGHTLY DUE TO EXISTING FIELD CONDITIONS AND SHALL BE VERIFIED IN THE FIELD BY THE CONTRACTOR PRIOR TO PROCEEDING WITH WORK. IF THERE IS A DISCREPANCY BETWEEN THE GIVEN DIMENSION AND THE ACTUAL DIMENSION, NOTIFY ARCHITECT PRIOR TO PROCEEDING WITH THE WORK.

MORE THAN 88” IN WIDTH SHALL BE PROVIDED WITH NOT LESS THAN ONE INTERMEDIATE

SEX, SEPARATE FACILITIES SHALL BE PROVIDED FOR PERSONS WITH DISABILITIES OF

THE HANDGRIP PORTION OF HANDRAILS SHALL BE NOT LESS THAN 1-1/4” OR MORE THAN

THE DOOR POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. ANY DAMAGE DONE BY THE CONTRACTOR TO THE EXISTING BUILDING, EQUIPMENT, OR FURNISHING SHALL BE PATCHED TO MATCH THE EXISTING ADJACENT, UNDAMAGED CONSTRUCTION OR REPAIRED TO “LIKE NEW” CONDITION. ALL SUCH PATCHING/REPAIRING SHALL BE DONE AT THE CONTRACTOR'S EXPENSE.

WHERE SEPARATE FACILITIES ARE PROVIDED FOR NON-DISABLED PERSONS OF EACH

OR RETURNED SMOOTHLY TO THE FLOOR, WALL, OR POST. WHERE THE STAIRS ARE

HAND-ACTIVATED DOOR OPENING HARDWARE SHALL BE CENTERED BETWEEN 30” AND ONE SET OF APPROVED CONSTRUCTION DOCUMENTS ARE TO BE KEPT ON SITE AT ALL TIMES.

STAIRWAYS SHALL HAVE HANDRAILS ON EACH SIDE, AND EVERY STAIRWAY REQUIRED TO BE

TREAD WIDTH BEYOND THE BOTTOM NOSING.

ALL ENTRANCES AND ALL EXTERIOR GROUND FLOOR EXIT DOORS TO BUILDINGS AND UNLESS OTHERWISE SHOWN OR NOTED, ALL TYPICAL DETAILS SHALL BE USED WHERE APPLICABLE.

SPACES DESIGN STUDIO

STAIRWAYS

GENERAL NOTES

CONTROLS FOR WATER CLOSET FLUSH VALVES SHALL BE MOUNTED ON THE WIDE SIDE OF TOILET AREAS.

FLOOR OR GROUND SPACE SHALL BE INCREASED TO 42” BY 48” WHEN SUCH SPACE IS PERPENDICULAR TO AN ADJACENT SEATING SPACE). THE MINIMUM

CHECKED BY

CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS MAY BE POSITIONED FOR FORWARD OR PARALLEL APPROACH TO AN OBJECT. CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS MAY BE PART OF THE KNEE SPACE REQUIRED UNDER SOME OBJECTS. ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR GROUND SPACE FOR A

MR. LUIS DE MORAES SHEET TITLE

WHEELCHAIR SHALL ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE OR ADJOIN ANOTHER WHEELCHAIR CLEAR FLOOR SPACE. IF A CLEAR FLOOR OR GROUND SPACE FOR A WHEELCHAIR IS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OF THREE SIDES, ADDITIONAL MANEUVERING CLEARANCES SHALL BE PROVIDED. THE SPACE REQUIRED FOR A WHEELCHAIR TO MAKE A 180-DEGREE TURN IS A CLEAR SPACE OF 60” DIAMETER OR A T-SHAPED SPACE.

GENERAL NOTES

SHEET NO.

THE MINIMUM CLEAR WIDTH REQUIRED FOR A WHEELCHAIR TO MAKE A 180 DEGREE TO TURN AROUND AN OBSTRUCTION SHALL E 36” WHERE THE OBSTRUCTION IS 48” OR MORE IN LENGTH AND 42” AND 48” WHERE THE OBSTRUCTION IS LESS THAN 48” IN LENGTH.

CS - 02

STORAGE FACILITIES & AREAS

DIAMTER

DRAWERS ARE PROVIDED WHERE ACCESS IS REQUIRED BY SECTION 101.17.11, AT

DIAG

DIAGONAL

LAV

LAVATORY

LEAST ONE OF EACH TYPE SHALL BE ACCESSIBLE IN TERMS OF CLEAR SPACE,

DIM

DIMENSION

LIN

LINEN

DISP

DISPOSAL'DISPENSER

LKR

LOCKER

DIV

DIVISION

LOUV

LOUVER

DOWN

LIGHT

DOOR OPENING

DOOR

M.O.

ENING

DISHWASHER

DWR

IF FIXED STORAGE FACILITIES SUCH AS CABINETS, SHELVES, CLOSETS, OR

A POINT (24” MAXIMUM LENGTH) AND 36” CONTINUOUSLY.

REACH RANGES, AND HARDWARE. ADDITIONAL STORAGE MAY BE PROVIDED OUTSIDE OF REQUIRED REACH RANGES.

IF THE CLEAR FLOOR SPACE ONLY ALLOWS FORWARD APPROACH TO AN OBJECT, THE MAXIMUM HIGH FORWARD REACH ALLOWED SHALL BE 48”. SEE FIGURE

A CLEAR FLOOR SPACE AT LEAST 30” BY 48” THAT ALLOWS EITHER A FORWARD OR

11B-5C(A). THE MINIMUM LOW FORWARD REACH IS 15”. IF THE HIGH FORWARD

PARALLEL APPROACH BY A PERSON USING A WHEELCHAIR SHALL BE PROVIDED

REACH IS OVER AN OBSTRUCTION, REACH AND CLEARANCES SHALL BE AS SHOWN

AT ACCESSIBLE STORAGE FACILITIES.

IN FIGURE 11B-5C(B). ACCESSIBLE STORAGE SPACES SHALL BE WITHIN AT LEAST ONE THE HEIGHT IF THE CLEAR FLOOR SPACE ALLOWS PARALLEL APPROACH BY A PERSON IN A

RANGES SPECIFIED IN SECTIONS 1118B.5 & 1118B.6.

WHEELCHAIR, THE MAXIMUM HIGH SIDE REACH ALLOWED SHALL BE 54” AND THE LOW SIDE REACH SHALL BE NO LESS THAN 9” ABOVE THE FLOOR AS SHOWN IN

HARDWARE FOR ACCESSIBLE STORAGE FACILITIES SHALL BE WITHIN AT LEAST

FIGURES 11B-5D(A) & (B). IF THE SIDE REACH IS OVER AN OBSTRUCTION, THE

ONE OF THE HEIGHT RANGES SPECIFIED IN SECTIONS 1118B.5 & 1118B.6 AND

REACH AND CLEARANCES SHALL BE AS SHOWN IN FIGURE 11B-5D(C).

SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE THE U-SHAPED PULLS ARE ACCEPTABLE. HARDWARE SHALL BE NO GREATER THAN 5 POUNDS. TOUCH LATCHES AND

FIXED OR BUILT-IN SEATING, TABLES, & COUNTERS WHERE FIXED OR BUILT-IN SEATING, TABLES, OR COUNTERS ARE PROVIDED FOR THE PUBLIC, AND IN GENERAL EMPLOYEE AREAS, 5%, BUT NEVER LESS THAN 1 MUST BE ACCESSIBLE, AS REQUIRED IN SECTION 1122B. THE TOPS OF TABLES AND COUNTERS SHALL BE 38” TO 34” FROM THE FLOOR OR GROUND.

SPACE BY MORE THAN 19”. WHERE A SINGLE COUNTER CONTAINS MORE THAN ONE TRANSACTION STATION, SUCH AS (BUT NOT LIMITED TO) A BANK COUNTER WITH MULTIPLE TELLER WINDOWS OR A RETAIL SALES COUNTER WITH MULTIPLE CASH REGISTER STATIONS, AT LEAST 5% BUT NEVER LESS THAN 1, OF EACH TYPE OF STATION SHALL BE LOCATED AT A SECTION OF COUNTER THAT IS AT LEAST 36” LONG AND NO MORE THAN 28” TO 34” HIGH.

SIGNS & IDENTIFICATION

A.B.

ANCHOR BOLT

ABV.

ABOVE

A/C

AIR CONDITIONING

A.A.

TILEACOUSTICAL TILE

A.B.

ACOU

ACOUSTICAL

THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL CONSIST OF A WHITE

ADD'L

ADDITIONAL

FIGURE ON A BLUE BACKGROUND. THE BLUE SHALL BE EQUAL TO COLOR

ADJ

ADJUSTABLE/ADJACENT

A.F.F.

ABOVE FINISHED FLOOR

NO.15090 IN FEDERAL STANDARD 599B. LETTERS AND NUMBERS ON SIGNS SHALL HAVE A WIDTH-TO-HEIGHT RATIO OF BETWEEN 3:5 AND 1:1 AND A STROKE WIDTH-TO-HEIGHT RATIO BETWEEN 1:5 AND 1:10.

AGGR

AGGREGATE

ALUM

ALUMINUM

CHARACTERS AND NUMBERS ON SIGNS SHALL BE SIZED ACCORDING TO THE

ANOD

ANODIZED

VIEWING DISTANCE FROM WHICH THEY ARE TO BE READ. THE MINIMUM HEIGHT IS

APPROX

APPROXIMATE

ARCH

ARCHITECTURAL

AUTO

AUTOMATIC

MEASURED USING AN UPPER CASE X. LOWER CASE CHARACTERS ARE PERMITTED. FOR SIGNS SUSPENDED OR PROJECTED ABOVE THE FINISH FLOOR IN COMPLIANCE WITH SECTION 1121B, THE MINIMUM CHARACTER HEIGHT SHALL BE 3”.

AVG

AVERAGE

CHARACTERS AND SYMBOLS SHALL CONTRAST WITH THEIR BACKGROUND,

BOARD

EITHER LIGHT CHARACTERS ON A DARK BACKGROUND OR DARK CHARACTERS ON

BLCG

MECHANICAL

STOR

STORAGE

STRUCT

STRUCTURAL

SUSP

SUSPENDED

SYM

SYMMETRICAL

SYST

SYSTEM

T&G

TONGUE & GROOVE

T.B.

TOWEL BAR

T.C.

TOP OF CURB

MEMB

MEMBRANE

MFR

MANUFACTURER

MIN

MINIMUM

EMERGENCY

MISC

MISCELLANEOUS

ENCL

ENCLOSURE

MTD

MOUNTED

ENGR

ENGINEER

MTL

METAL

EPB

ELECTRICAL PANEL BOARD

MUL

MULLION

EQUAL

TEL

TELEPHONE

EQUIP

EQUIPMENT

NORTH

TER

TERRAZZO

EXP

EXPANSION

N.I.C.

NOT IN CONTRACT

T.P.D.TOILET PAPER DISPENSER

NUMBER

T.V.

TELEVISION

EXT

EXTERIOR

EXTR

EXTRUDED

NOM

NOMINAL

T.W.

TOP OF WALL

F.A.

FIRE ALARM

NTS

NOT TO SCALE

THK

THICK

FAB

FABRICATE

TRD

TREAD

FAU

FORCED AIR UNIT

O.C.

ON CENTER

TYP.

TYPICAL

FDN

FOUNDATION

O.D.

OUTSIDE DIAMETER

F.D.

FLOOR DRAIN

UNF

UNFINISHED

OVERALL

OBS

OBSCURE

OFF

OFFICE

OPNG

OPENING

VERT

OPP

OPPOSITE\

F.E.

FIRE EXTINGUISHER

FEC

FIRE EXTINGUISHER CABINET

FIN

FINISH

FLOOR

FLUOR

FLUORESCENT

F.O.C.

FACE OF CONCRETE

P.LAM

PLASTIC LAMINATE

F.O.F.

FACE OF FINISH

PLATE

F.O.S.

FACE OF STUD

PLAS

PLASTER

F.S.

FULL SIZE

FRPF

FIRE PROOFING

PLUMB

PLUMBING

FOOT/FEET

PLYWOD

PLYWOOD

FTG

FOOTING

PAIR

FURR

FURRING

PRCST

PRECAST POINT

BLOCKING

GAUGE

PTD

PAINTED

BLDG

BUILDING

GALV

GALVANIZED

PTN

PARTITION

WHEN RAISED CHARACTERS OR SYMBOLS ARE USED, THEY SHALL CONFORM TO

BLK

BLOCK

G.B.

GRAB BAR

THE FOLLOWING:

Q.T.

QUARRY TILE

BEAM

GLASS/GLAZING

BOTTOM

QUAL

QUALITY

LETTERS AND NUMBERS ON SIGNS SHALL BE RAISED 1/32” MINIMUM AND SHALL BE

BOT

SANS-SERIF UPPERCASE CHARACTERS ACCOMPANIED BY GRADE 2 BRAILLE.

BSM

BASEMENT

GND

GROUND

QUANT

QUANTITY

CENTERLINE

GRADE

(R)

REMOVE

CAB

CABINET

GYP.

BD. GYPSUM BOARD

RISER/RADIUS

CEM

CEMENT

HOLLOW CORE

R/A

RETURN AIR

CER

CERAMIC

HAND OR HEAD

RESILIENT BASE

C.G.

CORNER GUARD

HDWD

HARDWOOD

C.I.

CAST IRON

R.D.

ROOF DRAIN

HDWE

HARDWARE

ARE SPECIFICALLY REQUIRED IN OTHER PORTIONS OF THESE REGULATIONS.

CLG

CEILING

REF

REFERENCE

DOTS SHALL BE 1/10” ON CENTERS IN EACH CELL WITH 2/10” SPACE BETWEEN CELLS. DOTS SHALL BE RAISED A MINIMUM OF 1/40” ABOVE THE BACKGROUND.

CLKG

CAULKING

HOLLOW METAL

REFR

REFRIGERATOR

CLO

CLOSET

HORIZ

HORIZONTAL

REINF

REINFORCED

ALL BUILDING ENTRANCES THAT ARE ACCESSIBLE TO AND USABLE BY PERSONS

CLR

CLEAR

HOUR OR HANDRAIL

REQ'D

REQUIRED

WITH DISABILITIES AND AT EVERY MAJOR JUNCTION ALONG OR LEADING TO AN

CMU

CONC. MASONRY UNIT

HEIGHT

RESIL

RESILIENT

CNTR

COUNTER

HTG

HEATING

C.O.

CASED OPENING

RGTR

HVAC

HEATING, VENTILATION & A/C

COL

COLUMN

ROOM

CONC

CONCRETE

HOT WATER

WHEN PERMANENT IDENTIFICATION IS PROVIDED FOR ROOMS AND SPACES,

R.O.

ROUGH OPENING

RAISED LETTERS SHALL BE PROVIDED AND SHALL BE ACCOMPANIED BY BRAILLE

CONN

CONNECTION

I.D.

INSIDE DIAMTER (DIM)

SOUTH

CONSTRY

CONSTRUCTION

INCAND

INCANDESCENT

S/A

SUPPLY AIR

CONTR

CONTRACTOR

INSUL

INSULATION

SOLID CORE

CORR

CORRIDOR

INT

INTERIOR

CORRUG

CORRUGATED

SCHED

SCHEDULE

FINISHED FLOOR TO THE CENTERLINE OF THE SIGN. MOUNTING LOCATION SHALL

JAN

JANITOR

BE DETERMINED SO THAT A PERSON MAY APPROACH WITHIN 3” OF SIGNAGE

CPT

CARPET

SEAL

SEALANT

CTR

CENTER

JST

JOIST

SECT

SECTION

CTSK

COUNTERSUNK

JOINT

S.E.A.

SEE ELECTRICAL DWG.

K.P.

KICKPLATE

SEL

SELECT

SHELF

SHR

SHOWER

SHT

SHEET

THE BORDER DIMENSION OF THE PICTOGRAM SHALL BE A MINIMUM OF 6” IN HEIGHT. CONTRACTED GRADE 2 BRAILLE SHALL BE USED WHEREVER BRAILLE SYMBOLS

ACCESSIBLE ROUTE OF TRAVEL SHALL BE IDENTIFIED WITH A SIGN DISPLAYING THE INTERNATIONAL SYMBOL OF ACCESSIBILITY AND WITH ADDITIONAL DIRECTIONAL SIGNS, AS REQUIRED, TO BE VISIBLE TO PERSONS ALONG APPROACHING PEDESTRIAN WAYS.

IN CONFORMANCE WITH SECTIONS 1117B.5.6. THROUGH 117B.5.6.3. SIGNS SHALL BE INSTALLED ON THE WALL ADJACENT TO THE LATCH SIDE OF THE DOOR. WHERE THERE IS NO WALL SPACE ON THE LATCH SIDE, INCLUDING AT DOUBLE LEAF DOORS, SIGNS SHALL BE PLACED ON THE NEAREST ADJACENT WALL, PREFERABLY ON THE RIGHT. MOUNTING HEIGHT SHALL BE 60” ABOVE THE

WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE SWING OF A DOOR. POLE SUPPORTED PEDESTRIAN TRAFFIC CONTROL BUTTONS SHALL BE

C.W.

COLD WATER

YELLOW BAND 2” IN WIDTH ENCIRCLING THE POLE, AND A 1” WIDE DARK BORDER

DBL

DOUBLE

KIT

KITCHEN

BAND ABOVE AND BELOW THIS YELLOW BAND. COLOR CODING SHOULD BE

DEPT

DEPARTMENT

LAB

LABORATORY

DET

DETAIL

LAM

LAMINATE

IDENTIFIED WITH COLOR CODING CONSISTING OF A TEXTURED HORIZONTAL

PLACED IMMEDIATELY ABOVE THE CONTROL BUTTON. CONTROL BUTTONS SHALL BE LOCATED NO HIGHER THAN 48” ABOVE THE SURFACE ADJACENT TO THE POLE.

ST. STAINLESS STEEL

MECH

PICTORIAL SYMBOL SIGNS (PICTOGRAMS) SHALL BE ACCOMPANIED BY THE EQUIVALENT VERBAL DESCRIPTION PLACED DIRECTLY BELOW THE PICTOGRAM.

EXISTING

GAS

RAISED CHARACTERS OR SYMBOLS SHALL BE A MINIMUM OF 5/8” HIGH.

SEE STRUCTURAL DWG.

(E)

A LIGHT BACKGROUND.

S.S.D.

STEEL

THAN 32” IN CLEAR WIDTH. STORAGE AREAS SHALL BE MADE ACCESSIBLE AS

STANDARD

STL

THE DOORWAY PROVIDING ACCESS TO STORAGE AREAS SHALL NOT BE LESS

POUND OR NUMBER

STD

MAXIMUM

EMER

SQUARE

MAX

ELEVATION

AND

EAST

ELEV

SPECIFICATION

HEIGHT AND DEPTH TO THE ROD OF SHELF SHALL COMPLY WITH FIGURE 11B-5D.

SHALL BE PROVIDED. SUCH CLEAR FLOOR SPACE SHALL NOT OVERLAP KNEE

SPEC

SHEET VINYL

ROD OR SHELF EXCEEDS 10”, AS IN CLOSETS WITHOUT ACCESSIBLE DOORS, THE

IF SEATING SPACES FOR PEOPLE IN WHEELCHAIRS ARE PROVIDED AT FIXED TABLES OR COUNTERS, CLEAR FLOOR SPACE COMPLYING WITH SECTION 1118B.4

SEE MECHANICAL DWG.

S.V.

ELECTRICAL

ABBREVIATIONS

S.M.D.

MATERIAL

ELECT

COUNTERS, KNEE SPACES AT LEAST 27” HIGH, 30” WIDE, AND 19” DEEP SHALL BE

SLIDING

MATL

EXPANSION JOINT

REQUIRED IN SECTION 1125B.

DRAWER

E.J.

APPROACH. WHERE THE DISTANCE FROM THE WHEELCHAIR TO THE CLOTHES

SIMILAR

MARBLE

EACH

CLOTHES RODS SHALL BE A MAXIMUM OF 54” FROM THE FLOOR FOR A SIDE

SIM

IF SEATING FOR PEOPLE IN WHEELCHAIRS IS PROVIDED AT FIXED TABLES OR PROVIDED.

LATERAL

DIA

THE MINIMUM CLEAR WIDTH FOR SINGLE WHEELCHAIR PASSAGE SHALL BE 32” AT

THE MINIMUM WIDTH FOR TWO WHEELCHAIRS TO PASS IS 60”.

LAT

U.O.N. NOTED

UNLESS OTHERWISE

SPACES DESIGN STUDIO SHIV CHOPRA

SDS 832 HILGARD AVENUE LOS ANGELES , CA - 90024 310- 866-7154 shivchopra@hotmail.com

CAL POLY POMONA/UCLA EXT MASTERS PROJECT INTERIOR ARCHITECTURE DOCUMENTS SPRING QUARTER 2017

THE DESIGNS AND DRAWINGS ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS. THESE SHALL NOT BE USED, MODIFIED AND DUPLICATED IN WHOLE OR IN ANY PART

URINAL VERTICAL

VEST

VESTIBULE

V.I.F.

VERIFY IN FIELD

WEST

WITH

WOOD

W/O

WITHOUT

W.P.

WATERPROOF

WEIGHT

PROJECT NAME

VEDA WELLNESS CENTER HOLISTIC WELLNESS CENTER

PROJECT LOCATION

14547 TITUS STREET PANORAMA CITY, CA 91402

DATE

06 / 11 / 2017 SCALE

3 / 16" = 1' - 0" DRAWN BY

SHIV CHOPRA CHECKED BY

MR. LUIS DE MORAES SHEET TITLE

GENERAL NOTES

SHEET NO.

CS - 03

SPACES DESIGN STUDIO SHIV CHOPRA

5'-8" MIN.

PROVIDE SECOND SET OF HANDRAILS AT 24' A.F.F. WHEN CHILDREN ARE PRIMARY USERS

32"

72"

1-1/2"

A.F.F.

1-1/2 MIN.

A.F.F.

54" MAX. FOR SIDE APPOACH

1-1/4"O.D

29' 42'

PHOTCELECTRIC TUBE BYPASS SWTCH

NOTES :PROVIDE BRAILLE SYMBOLS BELOW NUMERAL CHARACTER OR SYMBOL

2. 1/2" SLOPED BEVEL REQUIRED IF LEVEL CHANGE IS OVER 1/4" VERTICAL LEVEL CHANGE.

MASTERS PROJECT INTERIOR

PANEL EMERGENCY TELEPHONE

NOTES :1. 1/2" MAXIMUM TOTAL HEIGHT WITH 1/4" MAXIMUM VERTICAL CHANGE AT EDGE.

ARCHITECTURE DOCUMENTS

RAISED 1/8 INCH 1/32 ABOVE THE SURROUNDING SUPFCE

SPRING QUARTER 2017

4'-

TYP. CLR.

6'-0" TO 6'-9"

4'-6" MAX.

2'-11" MIN.

SIDE APPROACH

1-1/4" O.D 1-1/2"

4'-0" MAX.

BUTTON

MAXIMUM INSTALLATION HEIGHTS ABOVE CAB FLOOR

3. 1/4" MAXIMUM VERTICAL LEVEL CHANGE.

FRONT APPROACH

6. ALL CORRIDOR OPENINGS SHALL MEET THE REQUIREMENT OF BUILDING CODE INCLUDING STEEL FRAMES, 20 MIN LABELED DOORS, HINGES, LATCHING CLOSURES, TITLE 24, 1120A,3

CAL POLY POMONA/UCLA EXT

RAIL GRIP 1 1/2" MAX.

ELEVATOR ENTRANCE CRITERIA :MEDICAL EMERGENCY ELEVATORS SHALL BE PROVIDED WITH INTERNATIONAL SYMOL (STAR OF LIFT ( APPROX 3" HT ) LOCATED ON BOTH SIDES OF HOISTWAY FRAME 6'-6" AFF

HALL LANTERN (VISUAL & AUDIBLE) 2-1/2" MIN

60'

48" MAX. FOR FRONT APPROACH

7. FIRE RESISTIVE ASSEMBLIES FOR PROTECTION OF OPENINGS TO COMPLY WITH TITLE 24, 713

D 72' MIN

CONTROL PANEL (SEE DETAIL 'A')

LEVEL CHANGES

ELEVATOR STANDARD CARS

THRESHOLD

32 - 1"

35" MAX.

2. TENANT DOORS WILL HAVE HINGES AND CLOSURES BUT NO LOCKSET

6'-0" MIN.

2" TALL RAISED AND BRAILLE FLOOR LANDING NUMBERS ON BOTH SIDES OF DOOR JAMB PROVIDE BRAILLE SYMBOLS BELOW NUMERAL CHARACTER OR SYMBOL

42"

1/4" MAX

5. WIDTH AND HEIGHT OF REQUIRED EXIT DOORWAYS TO COMPLY WITH TITLE 24

NOTE:THE AUTOMATIC DOOR REOPENING DEVICE IS ACTIVATED IF AN OBJECT PASSES THROUGH EITHER LINE A OR LINE B. LINE A AND LINE B REPRESENT THE VERTICAL LOCATION OF THE DOOR REOPENING DEVICE NOT REQUIRING CONTACT.

shivchopra@hotmail.com

1-1/4" O.D 1-1/2"

1/2" MAX

4. EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT USE OF A SPECIAL KNOWLEDGE OR EFFORT

CALL BUTTOM 3/4" MINIMUM DIA. WITH VISUAL SIGNAL TO INDICATE CALL

310- 866-7154

3'-0" MIN. 1

3. EXIT DOORS SHALL SWING IN THE DIRECTIN OF EXIT TRACEL WHEN SO HAZARDOUS AREA OR WHEN SERVING AN OCCUPANT LOAD OF 50 OR MORE

ELEVATOR PLAN AND SECTION DRAWINGS.

(A) ELEVATOR CONTROL PANEL DETAIL

1/4" MAX

832 HILGARD AVENUE LOS ANGELES , CA - 90024

A.F.F

TRANSITION BETWEEN FLOOR FINISHES

HANDICAP SYMBOL OF ACCESSIBILITY NOTES :1. ALL COMPONENTS OF FIRE - RATED DOOR ASSEMBLIES SHALL BEAR THE APPROVED TESTING AGENCY, INCLUDING DOOR FRAME, LATCH, AND CLOSING

STAIR AND HANDRAILS DETAILS

35" MAX

NOTES :PROVIDE A 5"X5" SYMBOL OF ACCESSIBILITY AT ALL PRIMARY BUILDING ENTRANCES

60"

3/8" MIN. SEPARATION

STAIR SECTION VISUAL WARNING STRIPS SHALL BE 2" MIN. WIDTH AND INSTALLED 1' MAX. FROM EDGE OF THE TOP AND BOTTOM TREADS OF INTERIOR STAIRS, AND ON ALL TREADS OF EXTERIOR STAIRS.

1-1/4" O.D 1-1/2"

5/8" MIN. NUMERAL HEIGHT

4'-6" MIN.

1/2" MAX FILE HEIGHT

3/4" MIN. BRAILLE SYMBOL

6 4 2 B

5 3 1 S

4'-3" MIN.

PLACE STAR ALONGSIDE MAIN EXIT FLOOR NUMBER

4'-0" MAX.

BOTTOM LANDING

COMPRESSED CARPET 1/4" MAX BELOW THRESHOLD FIN. FLOOR LEVEL THRESHOLD TO THE SIGH

TW + 12'

5'-0" TO CENTER

34' TYP. TO FINISH FLOOR

34' TYP.

1 1/2" MAX.

SDS

IN TERNATIONAL SYMBOL OF ACCESSIBILITY

TW = TREAD WDTH 1'-0" MN.

TOP LANDING

1-1/4" O.D 1-1/2"

"RAISED REQUIREMENT FOR ELEVATOR CAR CONTROL AND CALL OPERATION BUTTONS

CENTER LONE OF HIGHEST BUTTONS (NOTE 4'-0" PREFERRED)

5'-8" MIN.

THE DESIGNS AND DRAWINGS

CENTER LINE OF EMERGENCY BUTTOMS TOP OF HANDRAIL

HOISTWAY & ELEVATOR

DOOR NOTES

THRESHOLDS

CONTROL PANEL

HANDRAILS

ELEVATOR ACCESSORIES

ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS. THESE SHALL NOT BE USED,

WHERE ADJACENT OBSTRUCTION OR WALL OCCURS

54' PREFERRED 48' MINMUM

MODIFIED AND DUPLICATED

48' MINMUM

12" MINIMUM IF DOOR HAS BOTH A CLOSER AND A LATCH

48"

4" MAX.

LOBBY

36' MINMUM

IN WHOLE OR IN ANY PART

DOOR TYPE:

ANY AMOUNT

REQUIRED CLEAR SPACE

1 MINIMUM 12" HIGH SMOOTH SURFACE AT DOOR BOTTOM, DOOR TYPE: EITHER ATTACHED PANEL OR BOTTOM RAIL

30"

HARDWARE

27" OR

BELOW

HIGHER

THAN 27"

24' MIN. EXTERIOR 18' MIN. INTERIOR

2. WHEN X < 20 INCHES, THEN Y SHALL BE 48 INCHES MAXIMUM.

CORRIDOR PLAN

24' MIN. EXTERIOR & 18' MINIMUM INTERIOR BEYOND STRIKE EDGE OF A GATE OR DOOR ON THE SIDE TOWARD WHICH IT SWINGS.

PROJECT NAME

48"

NOTES :1. X SHALL BE < 25 INCHES; Z SHALL BE > X

DOOR WIDTH PLUS

PLAN

5 MAXIMUM 8.5LBS. EFFORT TO OPERATE EXTERIOR DOOR 5LBS. FOR INTERIOR

Z 48"

30"

4 MOUNTED 36" TO 42"

48"

24' MIN. EXTERIOR 18' MIN. INTERIOR

RECUIRED CLEAR SPACE

2 OPENABLE FROM INSIDE WITHOUT USE OF KEY OR SPECIAL KNOWLEDGE OR EFFORT 3 OPENABLE BY SINGLE EFFORT LEVER-TYPE DEVICE (NOT REQUIRING GRASPING)

15" MIN.

48' MIN.

60' MINMUM

48"

VEDA WELLNESS CENTER

3. WHEN X IS 20 TO 25 INCHES, THEN Y SHALL BE 44 INCHES MAXIMUM.

WALKING PARALLEL TO A WALL

HIGH FORWARD REACH LIMIT

HOLISTIC WELLNESS CENTER

38" TO 42" LEVER OR U SHAPED HANDLE

MAXIMUM FORWARD REACH OVER AN OBSTRUCTION

12" MIN. BOTTOM RAIL OR PROVIDE KICK PLATE

48" MINIMUM

32" CLEAR

18" MIN. INTERICR

TITLE 24, CCR: CALIFORNIA BUILDING CODE ALL PRIVATELY FUNDED PUBLIC ACCOMMODATIONS AS DEFINED, AND COMMERCIAL FACILITIES, AS DEFINED, SHALL BE ACCESSIBLE TO PEOPLE WITH PHYSICAL DISABILITIES

WINDOW OPERATORS CONVENIENCE WALL OUTLET 1'-3" MIN.

4'-0" MAX.

46"

3. ANY CURB OR SIDEWALK INTENDED FOR PUBLIC USE THAT IS CONSTRUCTED IN THIS STATE WITH PRIVATE FUNDS.

CONTROLS, SWITCHES AND OUTLETS

CLEAR FLOOR SPACE PARALLEL APPROACH

HIGH AND LOW SIDE REACH LIMITS

4. ALL EXISTING PRIVATELY FUNDED PUBLIC ACCOMMODATIONS WHEN ALTERATIONS, STRUCTURAL REPAIRS OR ADDITIONS ARE MADE TO SUCH PUBLIC ACCOMMODATION AS SET FOURTH UNDER SECTION 1134B.

MAXIMUM SIDE REACH OVER AN OBSTRUCTION

SOAP DISP.

48" MINIMUM

60" MINIMUM

1. WIDTH TO HEIGHT RATIO BETWEEN 3 : 5 AND 1 :1 18" MIN. 24 PREFERRED

TAMPON DISP.

TAMPON VENDOR

HAND DRYER

TOILET PAPER DISP. & WASTE RECEP. GRAB BAR

2. STROKE WIDTH TO HEIGHT BETWEEN 1 : 5 AND 1 :10 3. CONTRAST CHARACTERS AND SYMBOLS WITH BACKGROUND.

38" - 40" (965 - 1219 mm) TO ENSURE FORWARD REACH

4. SANS SERIF CHARACTERS.

33" - 36" (838 - 914mm)

RESTROOMB

6" MAX. A

32" MAX

38" MAX.

6" MAX. 32" MAX.

48" MAX.

38" MIN.

MR. LUIS DE MORAES

42" MINIMUM

OF ACCESSIBILITY :-

48" MINIMUM

24" 12" MIN.

SHEET TITLE

18" 12" MIN.

12" MIN. 38" MIN.

42" MIN

32" MAX.

22"

INTERNATIONAL SYMBOL

1'-6" 3/4"

54" MIN 12" MAX

X 24" MIN.

40" MIN.

26" MIN.

33" - 36"

PULL SIDE

12" MAX.

SEAT COVER DISPENSER 24"

11. BUILDINGS. REMODELED TO PROVIDE ACCESSIBLE SANITARY FACILITIES FOR PUBLIC USE SHALL HAVE INFORMATION POSTED IN THE LOBBY AS PART OF THE BUILDING DIRECTORY.

MENB

250 LBS. CAPACITY GRAB BAR

40" - 36"

OF THE SIGH

GRAB BARS, TYPICAL

12. STANDARD USED TO IDENTIFY ACCESSIBLE FACLITIES

BACKING PLATE, TYPICAL

A.D.A GUIDELINES

13. WHITE FIGURE ON BLUE BACKGROUND, COLOR # 15090 ON FEDERAL STANDARD # 595A. 14. WHEN ENFORCING AGENCY DETERMINES IF APPOPRIATE, SPECIAL DESIGNS AND COLORS MAY BE APPROVED.

8" MIN.

C. LATCH SIDE APPROACHES - SWINGING DOORS

MANEUVERING CLEARANCES AT DOORS

GENERAL NOTES

TOILET AND LAVATORIES

CS - 04

2'-6"

18" MIN.

FROM WALL

MIN. 2'-5"

34" MAX

16. 0.2 INCH SPACE BETWEEN CELLS. 17. DOTS RAISED MINIMUM 0.025 INCH ABOVE BACKGROUND

MIN.

15. USE CONTRASTED GRADE 2 BRAILLE DOTS TO BE. 0.1 INCH ON CENTER IN EACH CELL

ALL DOOR IN ALCOVES SHALL COMPLY WITH CLEARANCES FOR FRONT APPROACHES.

2'-3"

MIN. IF DOOR HAS CLOSER

3'-4"

NOTE : - Y=48"

4'-0"

MIN. TO BOTTOM OF MIRROR

NOTE :Y=54" MIN. IF DOOR HAS CLOSER

SHEET NO.

1'-5"

BRAILLE:-

9" MIN.

5'-0" TO CENTER

SHIV CHOPRA

HANDICAP TUB - SHOWER - ACCESSORIES

10. ADDITIONAL DIRECTIONAL SIGNS ALONG ACCESSIBLE PATH OF TRAVEL ARE REQUIRED.

X 24" MIN.

NOTES :DOOR SIGH - SHALL BE CENTERED ON DOOR AND MOUNTED 60' ABOVE (W/ADHESIVE ONLY) AT. THE CENTER OF THE SIGH FINISH CONTRAST - THE CHARACTERS AND BACKGROUND OF SIGHS SHALL BE EGGSHELL, MATTE, OR OTHER NON - GLARE FINISH

RECESSED SOAP DISH

9. ALL ACCESSIBLE ENTRANCES IDENTIFIED WITH MINIMUM OF ONE STANDARD SIGN.

NOTE : - Y=48" MIN. IF DOOR HAS BOTH A AND LATCH CLOSER.

B. HINGE SIDE APPROACHES - SWINGING DOORS

PULL SIDE

CONTROL AREA

SIGNS / LOCATIONS.

NOTE : - X=36" MIN. IF Y=60"; X = 42" MIN. IF Y = 54"

BRAILLE SIGH

GRAB BAR SHOWER SEAT

CURTAIN ROD

CHECKED BY

8. VERTICAL CLEARANCE AT SUSPENDED SIGNS WITH MINMUM HEADROOM OF 80" REQUIRE MINIMUM 3" CHARACTER HEIGHT MEASURED BY USING UPPERCASE X CHARACTER AND NUMBERS SHALL BE SIZED ACCORDING TO VIEWING DISTANCE FROM WHICH ROAD. CASE CHARACTERS PERMITTED.

40"

Y WOMENS

42" MINIMUM

Y X

SOAP DISH

DRAWN BY

12" MIN. CURTAIN ROD

GRAB BAR TYP.

CONTRCL AREA

18"

54" MINIMUM

RAISED

N.T.S

12"

TYP.SIGH

7. SIGNS / PICTOGRAMS SHALL BE INSTALLED ON THE WALL ADJACENT TO DOOR LEADING TO THE ROOM OR SPACE THEY DESCRIBE AND AT 60" A.F.F. TO SIGN CENTERLINE AND WHERE A PERSON MAY APPROACH WITHIN 3" OF SIGNAGE WITHOUT ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE DOOR SWING AREA

PULL SIDE

12" MAX. 24"MIN. MAX.

CLOTHES LINE

18"

CURTAIN ROD

PROVIDE BACKING

23"

PULL SIDE

NOTES :SIGNAGE MUST IDENTIFY THE STAIR, INDICATE THE FLOOR LEVEL OF THE LANDING, WHERE THE STAIRWALL TERMINATES AT THE TOP AND BOTTOM, AND IDENTIFY AND SHOW THE DIRECTION TO THE EXIT DISCHARGE.

24" MIN. 27" MAX.

6. CHARACTERS AND BACKGROUNDS SHALL BE OF NON - GLARE CONTRASTING COLORS.

5/8"

5'-0" AFF.

A. FRONT APPROACHES - SWINGING DOORS

5. PICTOGRAMS / PICTORIAL SYMBOL SIGNS SHALL BE ACCOMPANIED BY THE EQUIVALENT VERBAL DESCRIPTION PLACED DIRECTLY BELOW THE PICTOGRAM. THE BORDER DIMENSION SHALL BE 6" MINIMUM HEIGHT.

NOTE : - X=12" IF DOOR HAS BOTH A CLOSER AND LATCH

40" (1016mm) MAX. TO BOTTOM OF REFLECTIVE SURFACE

F.F. LINE

SIGNS / PICTOGRAMS

BASEMENT TO 24 TH FLOOR ON ROOF AOCESS DOWN TO FIRST FLOOR FOR EXIT DISCHARGE

SIGNS / PICTOGRAMS

SCALE

MIRROR PAPERTOWEL WASTE RECEP.

LETTERS AND NUMBERS :-

WEST STAIR FLOOR

06 / 11 / 2017

DOORS

REACH REQUIREMENT

PULL SIDE

DATE

33" - 36"

34" MAX.

30"

2. WHERE DOORS OPEN ONTO, BUT NOT INTO A CORRIDOR, THE REQUIRED LEVEL AREA BEYOND THE DOORS MAY BE A MINIMUM OF 48" FOR ADDITIONAL INFORMATION, SEE APPLICABLE NOTES ON TYPICAL ACCESSIBILITY NOTES SHEET.

DOOR CLEAR SPACE

PANORAMA CITY, CA 91402

2. ANY SANITARY FACILITIES WHICH ARE MADE AVAILABLE FOR PUBLIC, CLIENTS OR EMPLOYEES IN SUCH ACCOMMODATIONS OF FACILITIES.

38" MIN.

VESTIBULE PLAN

1. ANY, STRUCTURE,FACILITY, COMPLEX OF IMPROVED AREA OR PORTIONS THEREOF WHICH IS USED BY THE GENERAL PUBLIC.

32" MAX.

NOTES :1. CLEAR SPACES MUST BE LEVEL TO PREVENT WHEELCHAIRS FROM ROLLING WHEN THE OCCUPANT RELEASES THE WHEEL GRIPS TO REACH FOR THE DOOR 1/4" PER FOOT IS ALLOWED FOR DRAINAGE.

3'-0" MIN.

RAMP LANDING AT DOORWAY PLAN

14547 TITUS STREET

AS FOLLOWS: CHAPTER 11-A,TITLE 24, CCR (AKA CALIFORNIA BUILDING CODE)

48"

SWITCHES

PROJECT LOCATION

RUBBER BUMPER ON CHAIR

CALIFORNIA STATE ACCESSIBILITY STANDARDS

30"

THERMOSTAT

54"

DOOR WIDTH PLUS 42'

24"

PULLL CORDS

48' MINIMUM

DOOR WIDTH PLUS 42'

24" MIN. EXTERICR OF BLDH

CLEAR FLOOR SPACE

ITEM NO.

MATERIAL

MANUFACTURER

PRODUCT NO.

SIZE

SUPPLIED BY

INSTALLED BY

REMARKS

LEAD TIME

FLOORING

ITEM NO.

MATERIAL

MANUFACTURER

PRODUCT NO.

SIZE

SUPPLIED BY

INSTALLED BY

REMARKS

LEAD TIME SPACES DESIGN STUDIO

MEN'S WASHROOM PLUMBING FIXTURES AND ACCESSORIES

SHIV CHOPRA

TIL. 1

PORCELAIN TILE FLOORING/CLADDING

AMERICAN OLEAN TEL: (805) 368-5209

AMERICAN OLEAN LH98

6" x 6" TILE

GENERAL CONTRACTOR

TO BE INSTALLED IN WASHROOMS

3 WEEKS

MW - 01

TOILET PAPER ROLL

KOHLER CO. TEL: (424) 116-7788

ARCHER SERIES K-11056-CP

HEIGHT : 8" DEPTH : 5"

GENERAL CONTRACTOR

TO BE INSTALLED IN WASHROOMS

6 WEEKS

TIL. 2

LIMESTONE TILE FLOORING

AMERICAN OLEAN TEL: (805) 368-5209

AMERICAN OLEAN L711 LIMESTONE TILE

6" x 6" TILE

GENERAL CONTRACTOR

TO BE INSTALLED IN CAFETERIA

3 WEEKS

MW - 02

W/C

KOHLER CO. TEL: (424) 116-7788

REVE SERIES K-3797-0

HEIGHT : 28" WIDTH : 18" DEPTH : 26"

GENERAL CONTRACTOR

WALL MOUNTED TOILET

6 WEEKS

TIL. 3

FLOORING FLOORING

AMERICAN OLEAN TEL: (805) 368-5209

AMERICAN OLEAN L712 LIMESTONE TILE

6" x 6" TILE

GENERAL CONTRACTOR

TO BE INSTALLED IN HEALTH STORE

3 WEEKS

MW - 03

GRAB BARS

KOHLER CO. TEL: (424) 116-7788

B 58-06 X 46"

LENGTH : 3'-7"

GENERAL CONTRACTOR

SHOULD BE A.D.A COMPLIANT

6 WEEKS

WDN. 1

SOLID WOOD FLOORING

ARMSTRONG FLOORS TEL: (310) 368-4456

ARMSTRONG ESP5254 WALNUT WOOD

12" X 6" PLANK

GENERAL CONTRACTOR

TO BE INSTALLED IN RECEPTION

3 WEEKS

MW - 04

HAND DRYER

DYSON AIR BLADE TEL: (311) 223-7997

B-35903

HEIGHT : 26" WIDTH : 9" LENGTH : 11"

GENERAL CONTRACTOR

ECO WALL MOUNTED IN ALL WASHROOMS

6 WEEKS

CONC.1

CONCRETE FLOORING

CONCRETE COLLABORATIVE TEL: (310) 436-2231

36" x 12" x 3/4"

GENERAL CONTRACTOR

ON SITE CAST CONCRETE

3 WEEKS

MW - 05

SINK

KOHLER CO. TEL: (424) 116-7788

PINOIR SERIES K-2028-1-0

SEE SPEC. BOOK FOR SIZE

GENERAL CONTRACTOR

PLUMBING PIPES NEED TO BE INSULATED

MW - 06

SOAP DISPENSER

KOHLER CO. TEL: (424) 116-7788

AUTO FOAM K-SG8637-0

SEE SPEC. BOOK FOR SIZE

GENERAL CONTRACTOR

HEIGHT SHOULD BE ADA 6 WEEKS COMPLIMENT

MW - 07

MIRROR

KOHLER CO. TEL: (424) 116-7788

VERDERA SERIES K-99571-TL-NA

HEIGHT :33" WIDTH : 24"

GENERAL CONTRACTOR

HEIGHT SHOULD BE ADA 6 WEEKS COMPLIMENT

BRANHAM SERIES K-4920-R-0

HEIGHT : 38" WIDTH : 18" DEPTH : 8"

GENERAL CONTRACTOR

MAINTAIN 30" BETWEEN COMPARTMENTS

IVORY

WALL FINISHES P-1 P-2 WC -1

WALL PAINT TYPE 1 WALL PAINT TYPE 2 WALLPAPER

PURE AND ORIGIONAL TEL: (424) 436-2277

FRESCO LIME MILKY WHITE

PER FIELD VERIFICATION

GENERAL CONTRACTOR

USE AS DEMARCATED ON FLOOR FINISH PLAN

2 WEEKS

BENJAMIN AND MOORE TEL: (223) 436-2277

CODE: 215

PER FIELD VERIFICATION

GENERAL CONTRACTOR

USE AS DEMARCATED ON FLOOR FINISH PLAN

2 WEEKS

PER FIELD VERIFICATION

GENERAL CONTRACTOR

USE AS DEMARCATED ON FLOOR FINISH PLAN

YORK WALL COVERING TEL: (551) 436-2002

CODE: MC 2727

3 WEEKS

WALL CLADDING TIL - 1

PORCELAIN TILE FLOORING/CLADDING

AMERICAN OLEAN TEL: (805) 368-5209

AMERICAN OLEAN LH98

OYNX WALL PANEL BACKLIT WITH LED

STONE LAND USA TEL: (310) 442-6688

LOCATION : A - 7

HIGH GLOSS LAMINATE PANEL BACKLIT

ARMSTRONG FLOORS TEL: (310) 368-4456

CODE: 78260

WP - 03

LAMINATE PANEL HIGH GLOSS FINISH

ARMSTRONG FLOORS TEL: (310) 368-4456

AL - 01

ALUMINUM FRAME BLACK IODIZED FINISH

WINDOW DESIGN GROUP TEL: (320) 886-3113

WC - 02

SOLID WOOD WALL COVERING

WC - 03

MW - 08

STANDING URINAL

KOHLER CO. TEL: (424) 116-7788

SDS 832 HILGARD AVENUE LOS ANGELES , CA - 90024

6 WEEKS

310- 866-7154 shivchopra@hotmail.com

CAL POLY POMONA/UCLA EXT MASTERS PROJECT INTERIOR ARCHITECTURE DOCUMENTS

MILLWORK WD - 1

OAK WOOD

HEARNE HARDWOODS TEL: (220) 445-8867

RED OAK SERIES

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE INSTALLED AS TABLE TOP ( SEATING)

2 WEEKS

WD - 2

AMERICAN WALNUT WOOD

HEARNE HARDWOODS TEL: (220) 445-8867

BLACK WALNUT SERIES

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

USED IN STAIRCASE, AND FOOD KIOSK

2 WEEKS

WD - 3

NATURAL WALNUT WOOD

HEARNE HARDWOODS TEL: (220) 445-8867

WALNUT SERIES

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED IN CUSTOM RECEPTION DESK

2 WEEKS

RED OAK WOOD STAIN FINISH

HEARNE HARDWOODS TEL: (220) 445-8867

RED OAK SERIES

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED IN CEILING FOR ROOM 103

2 WEEKS

WALL SCONCE

LOWE'S TEL: (410) 877-9009

CODE: # 190023217

HEIGHT : 9" LENGHT: 5 DEPTH : 5"

GENERAL CONTRACTOR

USED BEHIND RECEP. DESK

1 WEEK

MQTL1061-LED10.5K830

2" DIA

GENERAL CONTRACTOR

USED IN DISPLAY PANEL (HEALTH STORE)

1 WEEK

SPRING QUARTER 2017

GENERAL CONTRACTOR

TO BE INSTALLED IN WASHROOMS

3 WEEKS

GENERAL CONTRACTOR

TO BE INSTALLED IN RECEPTION, LIFT LOBBY

4 WEEKS

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED IN HEALTH STORE

2 WEEKS

CODE: L 6549

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED IN LIFT LOBBY

1 WEEK

LUXURY COLLECTION

5'10" x 3" x 3/4" 6'10" x 3" x 3/4" 7'9" x 3" x 3/4"

GENERAL CONTRACTOR

TO BE INSTALLED IN RECEPTION AREA

2 WEEKS

DL - 01

THE HOOME DEPOT TEL: (340) 889-6622

CODE: # 11141

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED IN RECEPTION AREA

2 WEEKS

DL - 02

SPOT LIGHT

LOWE'S TEL: (410) 877-9009

TINTED MIRROR CLADDING

CREO GLASS DESIGN TEL: (310) 886-7154

LUXURY COLLECTION

WIDTH : 8'-6" HEIGHT : 11-6"

GENERAL CONTRACTOR

TO BE INSTALLED IN HEALTH STORE

2 WEEKS

DL - 03

CHANDELIER

LOWE'S TEL: (410) 877-9009

CODE: # 34687

HEIGHT : 20" WIDTH : 18" DEPTH : 17"

GENERAL CONTRACTOR

USED OVER BANQUET SEATING

1 WEEK

LT - 01

FAUX LEATHER TILE CLADDING

KELEEN LEATHERS TEL: (610) 556-2244

CODE: JORDAN

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED IN HEALTHY FOOD CAFE

3 WEEKS

DL - 04

RECESSED CAN LIGHT FIXTURE (6" DIA)

LOWE'S TEL: (410) 877-9009

DLS22-06B30D1E-WH-1

6" DIA

GENERAL CONTRACTOR

TO BE USED IN CEILING AS PER DEMARCATED

2 WEEKS

LT - 02

FAUX LEATHER GOLD ACCENT TILE CLADDING

KELEEN LEATHERS TEL: (610) 556-2244

CODE: NADIA

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED IN HEALTHY FOOD CAFE

3 WEEKS

DL - 05

COVE LED LIGHT

LOWE'S TEL: (410) 877-9009

CONTACT: BRUNO TAN

6FT LONG

GENERAL CONTRACTOR

TO BE USED IN CEILING AS PER DEMARCATED

2 WEEKS

CONCRETE TILES

CONCRETE COLLABORATIVE TEL: (310) 436-2231

CODE: FOSSIL

12" X 24" TILE

GENERAL CONTRACTOR

TO BE INSTALLED UNDER STAIRCASE

2 WEEKS

DL - 06

RECESSED CAN LIGHT FIXTURE (8" DIA)

LOWE'S TEL: (410) 877-9009

MQTL1037-LED10.5K830

8" DIA

GENERAL CONTRACTOR

TO BE USED IN CEILING AS PER DEMARCATED

2 WEEKS

HOLISTIC WELLNESS CENTER

PROJECT LOCATION

WP - 01 WP - 02

CC - 01

6" x 6" TILE 10' x 3'5" x 2 1/2"

WALL BASE

WD - 4

THESE SHALL NOT BE USED,

CODE: V40C81P030

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED FOR ALL FLOORING EXCEPT WOODEN FLOORING

1 WEEK

STN - 01

GREY EMPRADOR MARBLE COUNTER

MARBLE OF THE WORLD TEL: (220) 478-8877

CODE: # MAR 860

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR FOOD KIOSK

1 WEEK

WOODEN BASE

ARMSTRONG FLOORS TEL: (222) 880-5599

CODE: ESP5254

PER FIELD VERIFICATION

GENERAL CONTRACTOR

TO BE INSTALLED FOR WOODEN FLOORING

1 WEEK

STN - 02

SATVARIO MARBLE COUNTER

MARBLE OF THE WORLD TEL: (220) 478-8877

CODE: # MAR 877

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR RECEPTION DESK

1 WEEK

BN - 01

STAINLESS STEEL BRUSH NICKEL FINISH

LOWE'S TEL: (410) 877-9009

N/A

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE INSTALLED WHERE REQUIRED

2 WEEKS

BR - 01

BRASS RAILING

LAVI INDUSTRY TEL: (343) 222-8796

FOOT RAILING (BRASS)

6FT

GENERAL CONTRACTOR

TO BE INSTALLED FOR FOOD KIOSK

2 WEEKS

PN - 01

ORANGE LACQUER FINISH PANEL

LWK KITCHENS TEL: (443) 778-5555

CONTACT: BRUNO TAN

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR FOOD KIOSK

2 WEEKS

PN - 02

LIGHT GREY LACQUER FINISH PANEL

LWK KITCHENS TEL: (443) 778-5555

CONTACT: BRUNO TAN

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR FOOD KIOSK

2 WEEKS

PN - 03

WHITE LACQUER FINISH PANEL

LWK KITCHENS TEL: (443) 778-5555

CONTACT: BRUNO TAN

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR RECEPTION DESK

2 WEEKS

FB - 01

UPHOLSTERY FABRIC FOR BANQUET

HOUZZ.COM

CODE: P6675

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR BACK REST

4 WEEKS

UPHOLSTERY FABRIC FOR BANQUET

HOUZZ.COM

T.B.D BY FABRICATOR

GENERAL CONTRACTOR

TO BE USED FOR SEAT

4 WEEKS

HD - 01

DRAWER METAL PULL

DOUGH MOCKET COMPANY TEL: (551) 436-2002

CODE: DP197-SSS

2 1/2" KNOB

GENERAL CONTRACTOR

TO BE INSTALLED FOR DRAWERS

2 WEEKS

HD - 02

CUPBOARD METAL PULL

DOUGH MOCKET COMPANY TEL: (551) 436-2002

CODE: DP129-SSS

7 1/2" HANDLE

GENERAL CONTRACTOR

TO BE INSTALLED FOR CUPBOARDS

2 WEEKS

ELEVATOR CAB / LIFT

LF - 04 LF - 05 LF - 06

PROJECT NAME

VEDA WELLNESS CENTER

MISCELLANEOUS LOWE'S TEL: (410) 877-9009

LF - 03

MODIFIED AND DUPLICATED IN WHOLE OR IN ANY PART

VYNL BASE

LF - 02

ARE COPYRIGHT PROTECTED AND ARE THE EXCLUSIVE PROPERTY OF SDS.

DECORATIVE LIGHT

LF - 01

THE DESIGNS AND DRAWINGS

WALNUT WOODEN GRAB BARS 3" DIA

OTIS LIFT COMPANY

DISPLAY SCREEN

OTIS LIFT COMPANY

CCTV CAMERA LIFT CONSOLE

OTIS LIFT COMPANY OTIS LIFT COMPANY

FLOOR DISPLAY SCREEN

OTIS LIFT COMPANY

GLASS PANEL

OTIS LIFT COMPANY