Outubro 2013 vol1 artel digilink by STERLING DO BRASIL

Outubro, 2013 - 1

inSIDEMEDIA O que acontece no mundo da multimidia Durante o IBC 2013 a ARTEL apresentou o novo DigiLink, completa plataforma de audio e video analogicos, 3G, SD-SDI, HD-SDI, com Switching sobre IP Se você não pode ver em Amsterdam, aqui está a linha completa

Simplifying Video Transport

Integrated Video Transport Platform

Spring 2013 Catalog

DigiLink Modular Video Transport System

Artel Video Systems is a leading global provider of broadcast-quality video transport hardware. A pioneer in the industry, Artel developed the world’s first commercially available video-over-fiber video transport platform. 30 years later, that passion for developing innovative products to meet the demanding requirements of broadcasters, CATV operators, telecommunications companies, and video service providers continues. Artel not only develops the best products, we stand behind them, offering superior customer service, off the shelf delivery, and free lifetime 24 x 7 technical support and firmware upgrades.

System Overview

Chassis Specifications

DigiLink Manager SNMP, HTTP Element Management System (EMS)

SFP/SFP+/XFP Removable External Optical and Electrical I/Os

DLC055 5x5 Multiport Video I/O Access to DL4360x Chassis

DLC103 3G Multi-Rate Digital Video Optical Transmitter/ Receiver/Transceiver/Repeater

DLC150E SDI/SDTI 4 Channel Analog/Digital AES Audio Embed and Optical Transmitter

DLC156M/D Six Channel TDM Multiplexers for 3G, HD, SDI, and ASI

DLC170AD Composite Video (NTSC/PAL) and Analog Audio to SDI Conversion with Optical Transmitter

DLC170DA SDI to Composite Video (NTSC/PAL) Analog Audio Conversion with Optical Receiver/Repeater

DLC205 Ethernet Aggregator and Optical Transceiver

DLC274 270 Mb/s Digital Video 4-to-1 TDM Multiplexer with Optical Transmitter/Receiver/Repeater

DLC300 3G-SDI Multi-Rate Digital Video Optical Transmitter/Receiver/Repeater

DLC410 DVB-ASI and SD-SDI Video-Over-IP Gateway

DLC450 HD-SDI Video-Over-IP Gateway

DLC610 HD-SDI JPEG2000 Compression with DVB-ASI Encapsulation

DLM205 Ethernet Aggregator and Optical Transceiver with On-Board Chassis Management

• VIDEO-OVER-OPTICAL NETWORKS

DLT710 Multi-Format Digital Video Generator and Test Module

• VIDEO ROUTING

Optical Multiplexers DWDM, CWDM, and WDM Modules

DigiLink, An Integrated Solution • VIDEO-OVER-FIBER • VIDEO-OVER-IP

• OPTICAL MULTIPLEXING • FORMAT CONVERSION • SIGNAL GENERATORS

• CIRCUIT VERIFICATION • ETHERNET TRANSPORT • ETHERNET SWITCHING • AUDIO EMBEDDING 05/23/13

Simplifying Video Transport

DigiLink Video Transport Platform DigiLink Video Transport System

OVERVIEW

Applications • Video-Over-Fiber • Video-Over-IP • Video-Over-Optical Networks • Video Routing • Optical Multiplexing • Format Conversion • Signal Generators • Circuit Verification • Ethernet Transport • Ethernet Switching • Audio Embedding Formats supported • 2.967 Gb/s 3G-SDI (SMPTE 424M) • 1.485 Gb/s HD-SDI (SMPTE 292M) • SD-SDI (SMPTE 259M-C, ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Other 270 Mb/s video services • Composite analog video & audio (NTSC, PAL) • 19.39 Mb/s ATSC (SMPTE 310M) • 10/100/1000 Ethernet Chassis features • Simplified deployment and configuration • 1, 4, and 12 slot options • Unlimited, non-spaced installation • Dual hot-swappable AC or DC power • Passive backplane • Internal video and Ethernet interconnect • On-board SNMP and HTTP element management system (EMS) Module features • Single-piece, hot-swappable • Front panel status LEDs and video monitoring • Common set of external removable optics • Available WDM, CWDM, and DWDM channels • Configured with on-board switches or DigiLink Manager • Multi-purpose, multi-format Certifications • NEBS Level 3 • GR-63 • GR-1089 • CSA 60950 • EN60950 • FCC Part 15 (Class A) • CISPR 22

DigiLink is a state-of-the-art modular platform leveraging Artel’s 30 years of carrier-class video transport experience. DigiLink is specifically designed to meet the need for a low cost, rugged, and simplified design for transporting broadcast-quality video and Ethernet across fiber, Ethernet, and optical networks. The most deployed solution for the North American metro-regional video-over-fiber market, DigiLink is used by all major broadcasters and networks for their critical contribution feeds for major sporting, news, and live events. DigiLink is the industry’s gold standard for simplicity of design, legendary reliability, and cost-effectiveness. A tightly integrated platform, it also offers uncompressed video-overIP transport, integrated video and Ethernet switching, and JPEG2000 compression making it an ideal solution for video over IP and managed optical networks. Designed specifically to meet the unique requirements of broadcast video transport, DigiLink features multi-purpose, single-piece function modules, multiple ruggedized chassis, external optics in all standard wavelengths, and front panel accessible status LEDs and video monitor ports for each module. NEBS Level 3 Certification across the entire platform ensures it is the most rugged and dependable video transport platform ever developed. DL4360x Chassis, 3RU, 12 Slot Active Routing

DigiLink Video Transport Platform

Simplifying Video Transport

DigiLink offers a chassis for any deployment or application. Function modules are deployable in any chassis creating a unified and integrated solution for all your video transport needs. Standard features on DL4360x, DL4300, and DL4000 • • • • • • • •

Space efficient: 4 function modules per RU, 10.5” deep Stackable non-spaced deployment. Side and front to rear cooling. Low power: 250 watts fully loaded for DL4360x and DL4300, 60 watts for DL4000 Quiet operation, low power design with variable fan speeds Rugged and reliable, NEBS Level 3 Certification DigiLink Manager integrated SNMP or HTTP monitoring and management Internal video and Ethernet communication eliminates external cross connect cabling and provides for remote routing and configuration Dual AC, DC, or one of each hot-swappable power supplies

DL4360x 3 RU 12 Slot Active Routing Features • 3RU 12 function module slots • Dual AC or DC removable power supplies • Optional 60 x 60 non-blocking video and Ethernet switch

DLX001 60x60 Crosspoint Module

DL4360x features an advanced design combining modular-based transport functionalities with internal routing capabilities for video and Ethernet traffic. By eliminating external cross connects while staying in native video or Ethernet format, the DL4360x streamlines routing and rerouting of video and Ethernet traffic, reducing operational expenses, and providing an ideal solution for remote sites where immediate and timely reconfiguration is required via EMS or NMS.

DL4000 1 RU 4 Slot Features • 1RU 4 function module slots • Dual AC or DC removable power supplies • Passive 16 x 16 internal video and Ethernet cross connects At 1 RU and capable of holding up to 4 function modules, the DL4000 is ideal for smaller deployments or for portable applications. Using a passive backplane design, the DL4000 is capable of internally routing video and Ethernet signals between modules.

DL4300 3 RU 12 Slot Features • 3RU 12 function module slots • Dual AC or DC removable power supplies

A larger version of the DL4000, the DL4300 is ideal for larger installations where internal cross connects are not a critical need.

DL4100 Single Slot

The DL4100 is an inexpensive, compact chassis holding one single slot DigiLink function module. External AC power supply.

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 3

DigiLink Video Transport System Chassis Options

DIGILINK CHASSIS SPECIFICATIONS CHASSIS MODEL

DL4360x

DL4300

DL4000

DL4100

PART #

390-009100-00

390-009000-00

390-008000-00

390-001000-00

Number of function module slots

12 1 or 2 AC, DC or 1 of each (Hot swappable)

4 1 or 2 AC, DC or 1 of each (Hot swappable)

Power supplies

Active fans Active fans 3 for function modules 3 for function modules 1 per power supply 1 per power supply 1 for active switch module

Cooling

1 AC external

Active fan 1 per power supply

Convection

Chassis dimensions (h, w, d)

5.25” x 17.0” x 10.5”

1.75” x 17.0” x 10.5”

Chassis wt. (Fully populated)

< 20 lbs

<10 lbs

Operating temperature

.83” x 5.88” x 10.5” <3 lbs

0 to 50° C

Relative humidity

0 to 40° C

10 to 95% (non-condensing)

Ambient storage

-40 to 80° C Yes, full 60x60 non-blocking. Requires optional switch module.

Yes, In banks of 4

Yes

NEBS Level 3 Certification

Yes

CSA 60950, EN60950, EN55022, FCC Part 15 (Class A), CISPR 22

Yes

DL4360x

DL4300

DL4000

Module-to-module internal connection Remote monitoring and management via DigiLink Manager REGULATORY CONFORMANCE

AC POWER SUPPLY SPECIFICATIONS CHASSIS MODEL PART # Integrated DigiLink Manager HTTP & SNMP interface Input voltage Power consumption (max) Current (max) BTU/hr (max)

DLP360 390-009102-00 No 250 watts 10 amps

DL4100

DLM301 DLP001 390-009002-00 390-008002-00 Yes No 90 to 254 VAC at 50 or 60 Hz 250 watts 60 watts (per chassis) 10 amps 1 amp

853

DL4360x

DL4300

205 (per chassis)

DLPE001 390-001002-00 No 15 watts .25 amps 55

DC POWER SUPPLY SPECIFICATIONS CHASSIS MODEL PART # Integrated DigiLink Manager HTTP & SNMP interface Input voltage Power consumption (Max) Current (Max) BTU/hr (Max)

DLP361 390-009105-00 No 250 watts 5 amps 853

DL4000

DLM302 DLP002 DLM130 390-009005-00 390-008005-00 390-008090-00 Yes No Yes -40 to -70 VDC 250 watts 60 watts (per chassis) 5 amps 1.5 Amps 853 205 (per chassis)

DL4360x CROSSPOINT MODULE DLX001 390-009109-00 < 20 Watts Active 1 fan RPM

AR206-008000-90_C

MODEL PART # Power consumption Cooling

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 4

Simplifying Video Transport

DigiLink Manager SNMP, HTTP Element Management System (EMS) DigiLink Video Transport System

FEATURES SNMPv2 and web monitoring and management • DigiLink chassis • Function modules • Power supplies

Provisioning • Configure function (transmitter/receiver/repeater) • Change input source (BNC or other module in chassis) • Configure IP settings • Enable or disable features and channels Non-volatile time stamped event log • Major/minor alarms • Startup sequence • New hardware installation • Configuration modifications • Video presence • Update of firmware • Revision status Maintenance • Download/upgrade firmware on function modules, power supplies and backplane • Download/upgrade management software

DigiLink Manager Home Page

DigiLink Manager is an HTTP and SNMPv2 based Element Management System (EMS) for monitoring, configuration, and management of DigiLink chassis, function modules, optics, and power supplies. Embedded in the DigiLink chassis and all its elements, it requires no external software or add-ins to monitor and configure all active elements of the platform. DigiLink Manager is compatible with all HTTP compatible systems, features a time-stamped log of key information about chassis activity, and is capable of monitoring and managing multiple chassis through a single Ethernet connection. With integrated SNMPv2, DigiLink Manager can easily integrate into third party NMS.

Manage module routing.

View chassis logs.

Manage all chassis in network.

Monitor function module status.

AR206-900130-00_E

Monitoring • Auto detect cards and configurations • Major and minor alarms and events • Detailed card status • Alarm status • Alarm details • Receive light levels • Temperature • Video status and rates

View diagnostics on function modules.

SFP/SFP+/XFP External Optical and Electrical I/Os Simplifying Video Transport

DigiLink Video Transport System

FEATURES

Industry standard SFP, SFP+, and XFP transceivers transmit and receive in one flexible unit Formats supported: • 2.970 Gb/s 3G-SDI (SMPTE 424M) • 1.485 Gb/s HD-SDI (SMPTE 292) • SD-SDI (SMPTE 259M-C ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Composite analog video & audio (NTSC, PAL) • 19.39 Mb/s ATSC (SMPTE 310M) • 10/100/1000/10000 Ethernet

DigiLink function modules feature externally accessible removable optical and electrical I/Os. Optical models function as both transmitter and receiver and are typically compatible across multiple modules simplifying the purchasing, sparing, and deployment process. Compatible with numerous third party electrical small form pluggable products provides additional flexibility in designing with DigiLink.

Industry standard wavelengths: • 1310 nm • 1550 nm • CWDM (ITU G.694.2) • DWDM (ITU G.694.1) Up to 33 dB loss budget LC/PC optical connectors Compatible with: • DigiLink optical filters • MegaWav • Other ITU G.694 standard filters

SPECIFICATIONS SFP Model

DLS31VX3G-11

DLS31VX3G-30

DLS55VX3G-30

DLSCxxVX3G-28

DLSWxxHX-33

DLSE45

DLSEHDBNC

393-051310-11

393-051310-30

393-051550-30

393-06xxxx-28

393-240033-xx

393-000101-00

393-000200-00

WDM

CWDM

DWDM

Electrical RJ-45

Electrical HD-BNC

1.25

1310 ±30

1550 ±40

ITU G.694.2 standard 1271 to 1611 ±6.5

ITU-T G.694.1 standard channels 21 to 60

Optical output power (min dBm)

-7

Optical output power (max dBm)

-2

Spectral width (nm)

0.4

Dispersion penalty

1 dB @ 80 km

2 dB @ 120 km

1 dB @ 120 km

Receiver sensitivity (dBm)

-18

-28

-29

Maximum input (dBm)

-2

-9

1250 to 1620

10-13

PART# Optical budget (dB) Type Maximum bit-rate (Gb/s) Transmitter Wavelength (nm)

Receiver

Input wavelength (nm) Bit error rate

1270 to 1610 10-13

SFP/SFP+/XFP External Optical and Electrical I/Os SPECIFICATIONS SFP+ Model

DLS+31X10G02Km

DLS+55X10G10Km

DLSC+xxX10G10Km

DLS+55X10G40Km

DLSC+xxX10G40Km

DLS+55X10G70Km

DLSC+xxX10G70Km

PART#

393-551310-04

394-021550-14

393-5561xx-14

393-551550-15

393-561xx1-15

393-551550-23

393-561xx1-23

2Km

10Km

40Km

70Km

WDM

CWDM

WDM

CWDM

WDM

CWDM

10Gbps

1310 ±45

1550 ±40

1271 to 1611 ±7.5*

1550 ±40

1471 to 1611 ±7.5

1550 ±40

1471 to 1611 ±7.5

Supported link distances Optical budget (dB) Optical band Data rate Transmitter Center wavelength (nm) Spectral width (nm) Optical launch power minimum (dBm) Optical launch power maximum (dBm) Dispersion penalty (dB)

-8.2

-1

3.2 dB

2 dB

3 dB

3 dB -23

Receiver Receiver sensitivity (dBm)

-12.6

-15

-16

-23

Maximum input (dBm)

0.5

-1

-7

Input wavelength (nm)

1260-1355

1260-1620

10-12

Bit error rate Gb/S_

XFP Model

DLX31X10G-8

DLX55X10-G-14

DLX55X10G-24

DLXCxxX10G-24

DLXDxxX10G-24

394-051310-08

394-051550-14

394-051550-24

394-06xxxx-24

394-2410xx-24

Type

WDM

CWDM

DWDM

Nominal bit-rate (Gb/s)

10.7

1310 ±30

1550 ±30

1550 ±40

ITU G.694.2 standard 1471 to 1611 ±6.5

ITU-T G.694.1 standard channels 21 to 60

Optical output power (min dBm)

-6

-1

-3

Optical output power (max dBm)

-1

Dispersion penalty

1 dB @ 80 km

2 dB @ 120 km

1 dB @ 120 km

Receiver sensitivity (dBm)

-14

-16

-24

-27

Maximum input (dBm)

0.5

-1

-7

Input wavelength (nm)

1290 to 1330

1260 to 1565

1530 to 1565

1260 to 1620

1525 to 1575

10-13

PART# Optical budget (dB)

Transmitter Wavelength (nm)

Receiver

Bit error rate

COMPATIBILITY SFP

DLC103*

DLC150E*

SFP+

DLC156M/D

DLC170AD

DLC170DA*

DLC205

DLC274M/D

DLC300

DLC410

DLC450 DLM205

XFP

AR206-010000-90_E

Module Model

P P

* Not compatible with DWDM optics.

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 7

5x5 Multiport Video I/O Access to DL4360x Chassis Simplifying Video Transport

FEATURES

Multiple Video I/O access to DL4360x • Five HD-BNC inputs • Five HD-BNC outputs Formats supported • DVB-ASI • SD-SDI (SMPTE 259M) • SDTI (SMPTE 305M) • HD-SDI (SMPTE 292M) • 3G-SDI (SMPTE 424M) • ATSC (SMPTE 310M)

[DLC055]

DigiLink Video Transport System

The DLC055 provides flexible video inputs and outputs as well as distribution amplifier capabilities to the DigiLink DL4360x Video and Ethernet Routing chassis. A DLC055 supports five independent inputs to the DLX001 crosspoint module as well as five outputs for each of twelve function slots in a DL4360x chassis. Each port is independent, supporting all standard video formats from 3G-SDI to ATSC. To ensure video quality and integrity all outputs are re-clocked. The DLC055 provides increased flexibility to the DL4360x by enabling inputs to be distributed to multiple modules in the chassis for separate compression, multiplexing, and transport. The five HD-BNC outputs are connected directly to the switch providing dozens of re-clocked electrical outputs for DA applications.

Reclocked outputs eliminate jitter Front panel status LEDs NEBS Level 3 Certified

DLC055 10 Port Video I/O

HD-BNC In A

Internal A

HD-BNC In B

Internal B

HD-BNC In C HD-BNC In D

Internal C Internal D

HD-BNC In E

Internal E

Internal A

HD-BNC Out A

Internal B

HD-BNC Out B

Internal C Internal D

HD-BNC Out C HD-BNC Out D

Internal E

HD-BNC Out E

5x5 Multiport Video I/O Access to DL4360x Chassis

[DLC055]

APPLICATIONS

Multi-Port Video I/O access for DL4360x Chassiss 3G HD SD ASI ATSC

DLC055

3G HD SD ASI ATSC

DLC055

3G HD SD ASI ATSC

DLC055

3G HD SD ASI ATSC

DL4360x DLC055

3G HD SD ASI ATSC

DLC055

3G HD SD ASI ATSC

DLC055

FEATURES SPECIFICATIONS Ordering Information

Environmental Operating Temperature Ambient storage temperature Relative humidity Power dissipation (watts) Physical Dimensions Weight

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) < 7 Watts 0.8” x 5” x 10.8” (1 slot in DL4360x chassis) <2 pounds, (1kg)

Video Interface Signal Formats 3G-SDI (SMPTE 424M) HD-SDI (SMPTE 292M) SD-SDI (SMPTE 259M) SDTI (SMPTE 305M) DVB-ASI Rates 270 Mb/s ±100ppm 1.485 Gb/s ± 100 ppm 1.485/1.001 Gb/s ± 100 ppm 2.970 Gb/s ± 100 ppm 2.970/1.001 ± 100 ppm Other rates passed in bypass mode

MODEL DESCRIPTION DLC055 5 x 5 Video I/O for DL4360x

PART # 390-009110-00

DL4360X CROSSPOINT MODULE SPECIFICATIONS MODEL PART # Power Consumption Cooling

DLX001 390-009109-00 < 20 Watts Active 1 fan RPM

Specifications are subject to change without notice.

Electrical Interface Input

Rear (5) HD-BNC 75ohm

Output

Rear (5) HD-BNC 75ohm

Return Loss >15 dB, 5-1485 MHz Cable Equalization for Belden 1694A type cable: 0 to 350 meters (270 Mb/s) 0 to 140 meters (1.485 Gb/s) 0 to 100 meters (2.967 Gb/s)

OUT

DLC055 front panel status LEDs

Regulatory Conformance NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 DLC055 rear panel video I/O and status LED

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 9

AR206-009110-B00_B

Compliance:

Simplifying Video Transport

FEATURES

Single card configurable as: • Transmit (electrical to optical) • Receive (optical to electrical) • Bi-directional (independent transmit and receive) • Repeat/Regenerate (optical to optical) • 4-channel distribution amplifier Automatic rate selection of all digital video formats • 2.967 Gb/s 3G-SDI (SMPTE 424M) • 1.485 Gb/s HD-SDI (SMPTE 292M) • 270 Mb/s - SD-SDI (SMPTE 259M-C, ITU 656) - SDTI (SMPTE 305M) - DVB-ASI • 19.39 Mb/s ATSC (SMPTE 310M)

3G Multi-Rate Digital Video Optical Transmitter/Receiver/ Transceiver/Repeater [DLC103] DigiLink Video Transport System

The DLC103 is a flexible, cost-effective, bi-directional fiber optic transport module for all digital video formats ranging from 19.39 Mb/s to 2.97 Gb/s. The module is user configurable to function as a transmitter, receiver, transceiver, repeater, or 4-channel distribution amplifier. The DLC103 can be deployed in all DigiLink chassis. Optics are externally accessible transceiver SFPs in 1310 nm, 1550 nm, and 18 CWDM wavelengths. All of these features add up to make the DLC103 the most flexible, easy-to-deploy, and reliable single channel digital video optical transport module ever developed.

Externally accessible SFP transceiver optics • Optical budget to 30 dB • WDM (1310 nm, 1550 nm) • CWDM ITU G.694.2 (channels 1271-1611) Inputs/outputs • Optical via SFPs • Electrical input (1) and outputs (3) via 75 ohm BNC • Input from and output to other modules in DigiLink chassis (via backplane) Multiple monitor options • Front panel monitor selectable between optical input and optical output (HD-BNC) • Front and rear panel status LEDs Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

DLC103 Digital Video Transceiver BNC In Internal

Keep Alive Signal

Input Select

Output Select

SFP

Reclock

Output Select

BNC Out A BNC Out B BNC Out C Internal

Output Select

Front HD-BNC

Digital Video-over-Fiber

3G Multi-Rate Digital Video Optical Transmitter/Receiver/ 3G 3G Transceiver/Repeater [DLC103] HD HD SD DLC103 ASI ATSC APPLICATIONS

DLC103

SD ASI ATSC

DLC103 DLC103

3G3G HD HD SDSD ASI ASI ATSC ATSC

3G HD SD DLC103 ASI ATSC

DLC103

10 to 95% (non-condensing) 6 watts

Physical Dimensions

3G HD SD ASI ATSC 3G HD SD ASI ATSC

3G HD SD ASI 3G ATSC HD SD ASI ATSC

Digital Video-over-Fiber with Repeater SPECIFICATIONS 3G HD Environmental SD DLC103 DLC103 Ambient 0 to 50°C ASI operating temperature ATSC Ambient storage temperature -40 to 80°C Relative humidity Power dissipation (watts)

3G HD SD ASI ATSC

DLC103

3G HD SD ASI ATSC

Bi-Directional Digital Video-over-Fiber

Bi-Directional Digital Video-over-Fiber Digital Video-over-Fiber 3G 3G HD HD SD DLC103 SD ASI ASI ATSC ATSC DLC103 3G HD Bi-Directional Digital Video-over-Fiber SD ASI 3G ATSC HD SD ASIVideo-over-Fiber with Repeater Digital ATSC DLC103 3G 3G HD HD SD DLC103 SD ASI ASI ATSC ATSC

Digital Video-over-Fiber

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Optical Interface Artel Video SFP See SFP Specification Sheet

DLC103

3G HD SD ASI ATSC 3G HD SD ASI ATSC

Digital Video-over-Fiber with Repeater 3G HD SD ASI ATSC

3G HD SD ASI ATSC

DLC103

3G HD Ordering Information SD ASI DLC103 Function Module ATSC MODEL DESCRIPTION DLC103 3G Multi-Rate, Digital Video Optical Transmitter/Receiver/Transceiver/ Repeater

3G HD SD ASI ATSC

DLC103

PART # 390-008215-00

SFP Optics See optics compatibility chart Monitor Cable MODEL DL100HDMC-72

DESCRIPTION Monitor Cable, HD-BNC to BNC, 72” long

PART # 396-001010-72

Note: Specifications are subject to change without notice.

Electrical Interface Signal Formats • 2.967 Gb/s - 3G-SDI (SMPTE 424M) • 1.485 Gb/s - HD-SDI (SMPTE 292M) • 270 Mb/s - SD-SDI (SMPTE 259M-C, ITU 656) - SDTI (SMPTE 305M) - DVB-ASI - ARTEL 270 Signal polarity Channels Connectors Input (1) Output (3) Monitor Return loss (with active video) Cable equalization for Belden 1694A type cable:

Non inverting 1-transmit, 1-receive BNC 75 ohm BNC 75 ohm HD-BNC 75 ohm >15 dB, 5-1485 MHz >10 dB, 1486-2967 MHz 0 to 350 meters (270 Mb/s) 0 to 140 meters (1.485 Gb/s) 0 to 100 meters (2.967 Gb/s)

Rear panel includes one electrical Input, three electrical outputs, and SFP transceiver cage

Regulatory Conformance

NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 AR208-008215-B00_H

Compliance:

Front panel monitoring and status display

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 11

Simplifying Video Transport

SDI/SDTI 4 Channel Analog/Digital AES Audio Embedded and Optical Transmitter [DLC150E] DigiLink Video Transport System

FEATURES Single card audio embedder and video transport Embed into SDI or SDTI • One-to-four analog audio channels • One or two AES-3 audio pairs • Asynchronous or synchronous digital audio • Standby video signal continues to deliver audio on loss of video input Optical transport (with or without embedded audio) • SD-SDI (SMPTE 259M-C, ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Analog Audio (4) • AES-3 (2 stereo pairs) • Full reclocking removes jitter from SDI Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (Channels 27-61) Inputs • Video (with or without embedded audio) • 75ohm BNC • Other modules on DigiLink chassis (via backplane) • Audio • Analog audio via 600ohm or high-Z balanced • AES-3 110ohm balanced • AES-3 75ohm unbalanced (DLC150E/D) Outputs • Optical via SFP • Other modules in DigiLink chassis (via backplane) Multiple monitoring options • Front panel monitor (mini 75ohm SMB) selectable between: • Input video (pre-embed) • Output video (post-embed) • Front and rear panel status LEDs Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

The DLC150E is a flexible audio embedder and video transport card designed for use in the DigiLink video transport system. The DLC150E will embed analog or AES audio into SDI and SDTI as well as transport all standard 270Mb/s digital formats. The DLC150 functions as both an audio embedder for four channel analog or two stereo pair AES-3 audio, and as a 270Mb/s video over fiber optics transport module. The DLC150 uses industry standard 1310nm, 1550nm, and CWDM Small Form-Factor Pluggable (SFP) optics. Provisioning and monitoring is accomplished using switches, LEDs, front monitor jack, SNMP or HTTP via DigiLink Manager.

DLC150E AES Encoder and SDI Audio Embedder AES CH 1 AES CH 2 Analog Audio CH 1 Analog Audio CH 2 Analog Audio CH 3 Analog Audio CH 4

SFP AES Encode

Internal Audio Embed

Video Standby Signal BNC Internal

Video Input Select

Input Select

Monitor Select

Front Mini SMB

Embed Analog Audio into SDI

SDI/SDTI 4 Channel Analog/Digital AES Audio Embed and Optical Transmitter [DLC150E]

SDI

APPLICATIONS

ANALOG AUDIO

Embed Analog Audio into SDI

Embed AES into SDI

SDI DLC150E ANALOG AUDIO

SDI AES

DLC150E

SDI AES

DLC150E

SDI AES

Embed AES into SDI

SPECIFICATIONS

SDI Environmental

DLC150E Operating temperature Ambient AESstorage temperature Relative humidity Power dissipation

SDI 0 to 50° CAES

-40 to 80°C 10 to 95% (non-condensing) 10 watts

Physical Dimensions Optical Interface Artel Video SFP

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

See SFP/XFP Specification Sheet

Analog Audio Features SMPTE 272M embedding of 2 analog stereo pairs (one to four analog signals) in SD-SDI (SMPTE 259M) or SDTI (SMPTE 305M) • 24-bit sampling @ 48kHz • 600ohm balanced and high-impedance balanced input (3-position terminal block) • 0 dBFS (full scale) adjustable from +16dBm to +28dBm in 2dB steps (600ohm) • Selectable target group (0, 1, 2, 3) • Option to not embed if audio present in the target group • Option to disable embedding for transport-only applications

Digital Video Features Transport of all 270Mb/s digital video • SD-SDI (SMPTE 259M) • SDTI (SMPTE 305M) • DVB-ASI (no audio embedding) • Automatic detection Jitter cleanup of SD-SDI and SDTI 75ohm BNC input • >15dB return loss • Cable equalization up to 300m (Belden 8281 or equivalent) EDH checking and generation for SD-SDI and SDTI Standby video generator • Selectable SD-SDI signal allows audio to be delivered when input video is lost • Selectable non-video keep alive maintains link operation while allowing downstream equipment to detect loss of signal when input video is lost DLC150E can be cascaded via backplane inputs and outputs for multi-group embedding Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22

Analog Audio Specifications

Ordering Information

Quantizing 24-bit Sampling rate 48 kHz Number of channels 4 analog audio balanced Connector 3-position terminal block plugs Input impedance 600ohm or >100Kohm, Switchable Input return loss >30 dB (600ohm) Input common mode rejection >60 dB 20Hz - 20kHz Input common mode range +/-10 V (20Vp-p) Maximum input level (clipping) 0 dBFS = +10 to +24dBm (600ohm) Adjustable in 2 dB steps Amplitude frequency response +/- 0.1 dB (20Hz to 20kHz) Distortion (THD+N) <0.05% (20Hz - 20kHz @+18 dBm) Intermodulation distortion <0.05% (SMPTE RP12, 60/7k, 4:1) Audio signal-to-weighted- > 90 dBA (referred to +18 dBm) noise ratio Audio channel crosstalk <-70 dB (20Hz - 20 kHz) Video crosstalk -85 dB Insertion gain 0.0 dB +/- 0.2dB Interchannel phase delay <1° (20Hz-20kHz) Audio-video delay <10 ms

DLC150E Function Module MODEL DLC150E

DESCRIPTION SDI Audio Embedder and Optical Transmitter

PART # 390-008050-00

SFP Optics See optics compatibility chart Monitor Cable MODEL DL100MC-72

DESCRIPTION Monitor cable, 75ohm mini -SMB TO BNC, 72”L

PART # 396-001001-00

Note: Specifications are subject to change without notice.

AES-3 Audio Features Front panel monitoring and status display

SFP Pluggable Optics

AR206-008050-C00_F

SMPTE 272M embedding of 2 digital audio streams (two stereo pairs) in SD-SDI (SMPTE 259M) or SDTI (SMPTE 305M) • Interfaces A, B, C, D, E, F, and G • AES-3 audio stream support for 110ohm balanced (3-position terminal block) • AES-3 audio stream support for 75ohm unbalanced (BNC) [Note: separate order number for unbalanced input] • Synchronous (48kHz) and asynchronous (32.0kHz, 44.1kHz, 48kHz) streams supported • Selectable target group (0, 1, 2, 3) • Option to not embed if audio present in the target group • Option to disable embedding for transport-only applications

Rear panel includes electrical video input, analog or AES audio inputs and SFP transceiver cage

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 13

6 Channel TDM Multiplexer for 3G, HD, SDI, and ASI

[DLC156]

Simplifying Video Transport

DigiLink Video Transport System

FEATURES Single wavelength optical transport for: • Six independent HD-SDI, SDI, or DVB-ASI channels • Three independent 3G-SDI channels • Combinations of both

The DLC156 is an innovative, six channel TDM multiplexer for transporting uncompressed and compressed video over dark fiber or managed optical networks such as ROADM and OTN. Users can mix and match SD-SDI, ASI, HD-SDI, or 3G-SDI services into a single 10.7 Gb/s optical transport stream.

Formats supported • 2.967 Gb/s 3G-SDI (SMPTE 424M) • 1.483516 Gb/s HD-SDI (SMPTE 292M) • 270 Mb/s • SD-SDI (SMPTE 259M-C, ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Other 270 Mb/s, 1.485 Gb/s, and 2.97 Gb/s services

The DLC156 is a space efficient, cost-effective module for transporting up to six HD-SDI or three 3G-SDI digital video services over a single optical wavelength, saving fiber cost and simplifying network design and deployment. Using time division multiplexing (TDM), each channel is assigned a fixed time-slot, eliminating complex configurations. Six independent, mixed format video signals are aggregated to a single wavelength and two time slots can be combined to carry 3G-SDI.

Externally accessible 10.7 Gb/s XFP transceiver optics • Optical budget to 24 dB • WDM (1310 nm, 1550 nm) • CWDM ITU G.694.2 • DWDM ITU G.694.1

The DLC156 supports links in excess of 80 km using industry standard, hot swappable 10G XFP transceivers in WDM, CWDM, and DWDM wavelengths. Installing a DLC156 repeater between the link source and destination extends the range of a link. Up to 240 uncompressed HD channels are possible over a single fiber. For additional flexibility, the DLC156 can also be used as a transport aggregator for Artel’s DLC274 four-channel TDM module supporting as many as 960 270 Mb/s video services over a single fiber.

Simple and easy configuration • On-board switches • DigiLink Manager Multiple monitoring options • Switch selectable front panel monitor of individual channels (HD-BNC) • Front and rear panel status LEDs • Loss of video (individual channels) • Loss of optical input • Laser (XFP) fail

With its format flexibility, easy configuration, and competitive price, the DLC156 is an ideal solution for fiber constrained, multi-service video transport applications.

Includes FEC for extended range and improved error performance

DLC156M 6 Channel Digital Video Multiplexer HD-BNC A Internal HD-BNC B Internal HD-BNC C Internal HD-BNC D Internal HD-BNC E Internal HD-BNC F

DLC156D 6 Channel Digital Video De-Multiplexer and Repeater

Input Select

HD-BNC A HD-BNC B HD-BNC C HD-BNC D HD-BNC E HD-BNC F

Input Select Input Select Input Select

TDM Mux

Framing

XFP 10.7G

FEC

DLC156M

XFP 10.7G

FEC Proccesing

De-Frame

TDM De-Mux

Internal Internal Internal Internal Internal

Input Select

Monitor Select

Front HD-BNC

Monitor Select

Front HD-BNC Repeated

Six Channels of mixed Digital Video-over-Fiber with drop and continue A B C D E F

3G HD SD ASI

6 Channel TDM Multiplexer for 3G, HD, SDI, and ASI

[DLC156]

DLC156M

3G HD SD ASI

Six Channels of mixed Digital Video-over-Fiber using TDM 3G HD SD ASI

3G HD SD ASI

A BCDE F

APPLICATIONS

A B C D E F

DLC156D

A B C D E F

DLC156D

DLC156M

Six Channels of mixed Digital Video over managed optical network with optional return path A B C D E F

3G HD SD ASI

A B C D E F

3G HD SD ASI

DLC156M

1310nm

MANAGED OPTICAL NETWORK

1 1310nm

DLC156D

A B C D E F

3G HD SD ASI

DLC156D

A B C D E F

3G HD SD ASI

Optical Wave Shifting

Six Channels of mixed Digital Video-over-Fiber with Repeater 3G HD SD ASI

A B C D E F

DLC156D

DLC156M

A B C D E F

DLC156D

3G HD SD ASI

Six Channels of mixed Digital Video-over-Fiber with drop and continue 3G HD SD ASI

A B C D E F

DLC156M

DLC156D

A B C D E F

3G HD SD ASI

DLC156M

DWDM

A B C D E F

3G HD SD ASI

A B C D

SD ASI

3G HD SD ASI

Alien Optical Lightwave

DLC274M

DLC274D

3G HD SD ASI

Six Channels of mixed Digital Video over managed optical network with optional return path A B

D E F Environmental

SD ASI

MANAGED OPTICAL NETWORK

1310nm

E F

Physical

DLC156D

Optical Wave Shifting

Ambient operating temperature Ambient storage temperature A Relative humidity B 3G C HD dissipation Power (watts) DWDM DLC156M D SD ASI

1 1310nm

E F

Alien Optical Lightwave

Dimensions Mixed Digital Video-over-Fiber Optical Interface

A B C D E F

3G HD SD ASI

Electrical Interface

3G HD SD ASI

• 2.97 Gb/s

A B C D E F

DLC156M

DLC156D

A B C D E F

DLC156M

DLC156D

A B C D E F

SD ASI

3G HD SD ASI

A B C D

DESCRIPTION Six Channel TDM Multiplexer for 3G, HD, SD-SDI, ASI Six Channel TDM De-Multiplexer for 3G, HD, SD-SDI, ASI

PART # 390-008200-00 390-008210-00

XFP Optics See optics compatibility chart Monitor Cable

0.8” x 5” x 10.8” (2 slot in DigiLink video platform chassis

Signal Formats

MODEL DLC156M DLC156D

ASI

SD VideoBXFP DLC274M Artel See SFP/XFP Specification SheetDLC274D C ASI D

A B C D E F

A B C D

Ordering Information

0 to 50°C -40 to 80°C A 10 to 95% (non-condensing)B MANAGED 3G C HD OPTICAL < 20 Watts XFP Optics) D (Including DWDM DLC156D D SD NETWORK

D DWDM

Mixed Digital Video-over-Fiber

A BCDE F

3G SPECIFICATIONS C HD DLC156M

MANAGED OPTICAL NETWORK

SD ASI

MODEL

DESCRIPTION

PART #

DL100HDMC-72 Monitor Cable, HD-BNC to BNC, 72” long

396-001010-72

3G HD SD ASI

- 3G-SDI (SMPTE 424M) • 1.483516 Gb/s - HD-SDI (SMPTE 292M) • 270 Mb/s - SD-SDI (SMPTE 259M-C, ITU 656) - SDTI (SMPTE 305M) - DVB-ASI Signal Polarity Non inverting Channels Six channels non 3G-SDI Three channels of 2.97 Gb/s Connectors Input (DLC156M) Six BNC 75 ohm Output (DLC156D) Six BNC 75 ohm Monitor One HD-BNC 75 ohm Return Loss >15 dB, 5-1485 MHz >10 dB, 1486-2967 MHz Cable Equalization for Belden 0 to 350 meters (270 Mb/s) 1694A type cable: 0 to 140 meters (1.483516 Gb/s) 0 to 120 meters (2.97 Gb/s)

DLC156M front panel monitoring and status display

XFP Pluggable Optics

Regulatory Conformance

NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22

AR206-008201-00_C

Compliance:

DLC156M rear panel video I/O, XFP cage and status LEDs

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 15

Simplifying Video Transport

FEATURES Single card composite video and analog audio to SDI conversion with optical transmitter (electrical to optical) Convert composite (NTSC/PAL) to SDI (SMPTE 259M) • Analog composite 75ohm video input BNC • Automatic NTSC-M / PAL-B/G format detection • 12-bit video composite to 10-bit component digital processing • Advanced, adaptive 3D comb filter Comprehensive VBI data handling • SMPTE 259M SD-SDI 270Mb/s output • Automatic and manual gain and equalization (150 meters) Convert analog audio to AES and embed into SDI • Balanced 600ohm analog audio inputs (4) • SMPTE 272M 24-bit, 48 kHz audio embedding Use with DLC170DA for optical transport of analog video and audio • Exceeds TV-1 and ANSI T1.502 “short haul” specification Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (channels 27-61) • DWDM ITU G.694.1 (channels 21-60) Interoperates with • Other DigiLink modules • DigiLink 1220/2701 (SDI mode) • Other non-scrambled or non-dithered SDI optical transmitters and receivers Multiple monitoring options • Front panel monitor (mini 75ohm SMB) selectable between: • NTSC or PAL (pre-conversion) • SDI (Post-conversion) • Front and rear panel status LEDs Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

Composite Video (NTSC/PAL) and Analog Audio to SDI Conversion with Optical Transmitter [DLC170AD]

DigiLink Video Transport System

The DLC170AD converts analog video and audio to SDI (SMPTE 259M) and provides optical transport. Used with the DLC170DA, the design insures full TV-1 RS250-C “short haul” analog performance over a true SMPTE 259M SD-SDI optical transport link. The DLC170AD uses advanced high performance 12-bit video processing with adaptive 3D comb filters to convert NTSC-M /PAL-B/G analog composite video to ITU-R BT.601/656 compliant, 525 or 625 line, 4:2:2 component digital video. Four channels of analog audio are converted to 24-bit digital signals and sampled at 48 kHz and then embedded into the digital video per SMPTE 272M for a total of 4 analog channels. The audio can be inserted into any one of the four groups. Using the backplane to provide jumper free connections, additional audio channel groups can be added by cascading the DLC170AD digital output to one or more DLC150E audio embedders. An SFP installed into the final module provides the optical output of the combined signals. A front panel monitor jack can be selected to output either analog or digital video. When set to analog, the incoming analog video can be checked for signal level and quality using conventional analog video equipment. When set to digital, the converted video in 270Mb/s SDI format with embedded audio can be checked using digital video test equipment.

DLC170AD NTSC/PAL and Analog Audio to SDI Analog Audio CH 1 Analog Audio CH 2 Analog Audio CH 3 Analog Audio CH 4

AES Encode AES Encode Video Standby Signal

NTSC/PAL

NTSC/PAL to SDI Conversion

SFP

SDI Audio Embed

Internal Input Select

Monitor Select

Front Mini SMB

Composite Video (NTSC/PAL) and Analog Audio to SDI Conversion with Optical Transmitter [DLC170AD] APPLICATIONS NTSC/PAL Video-over-Fiber with Repeater NTSC/PAL Video-over-Fiber

NTSC/PAL

NTSC/PAL ANALOG AUDIO

NTSC/PAL DLC170AD

DLC170DA

ANALOG AUDIO

NTSC/PAL DLC170AD

DLC103

DLC170DA

ANALOG AUDIO

Convert NTSC/PAL Video to SDI NTSC/PAL ANALOG AUDIO

DLC170AD

SPECIFICATIONS Analog Video to SDI Conversion (6)

Environmental SMPTE 259M via optical interface or backplane SMPTE-170M NTSC-M or ITU-R BT.624-4 PAL-B/G composite video 1.0 V p-p nominal ± 3 dB (1) ±10 V >30 dB

Operating temperature Ambient storage temperature Relative humidity Power dissipation

75ohm or Hi-Z >30 dB, 75ohm

Artel Video SFP

<0.10 dB <0.10 dB <0.10 dB <0.10 dB <1.0% <0.7 degrees <1.0% <±2% <5 nS >67 dB

Analog Audio to AES and Embed (6) Channels Input Input impedance Input common mode range Input common mode rejection Nominal (test) level Maximum level (0 dBFS clipping) Insertion gain Freq amplitude response (20 Hz to 20 kHz) THD+N (20-20k @ +18 dBm) SNR (weighted) Crosstalk @10kHz

4 (2) Balanced Analog 600ohm or >100Kohm ±30V >60 dB 18 dBm (3) +10 to +24 dBm (4) ±0.25 dB (5) ±0.3 dB

Audio to video lead/lag

<2 ms

0.01% >95 dBA 70 dB

(1) Automatic or manual control. (2) Specifications are with 48 kHz, 24-bit audio. (3) Nominal level is +20 dBm for 0 dBFS (clipping) with performance specifications based on a +18 dBm test level. (4) User selectable maximum (0 dBFS) level in eight 2 dB steps. (5) Each end set to the same nominal 0 dBFS level. (6) Analog specifications based on end-to-end performance with DLC170DA.

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) 10 watts

Physical Dimensions

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Optical Interface See SFP specification sheet

Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 Ordering Information DLC170AD Function Module MODEL DESCRIPTION DLC170AD Analog to SDI Conversion with Optical Transport SFP Optics

PART # 390-008070-00

See optics compatibility chart

Monitor Cable MODEL DL100MC-72

DESCRIPTION Monitor cable, 75ohm mini-SMB to BNC, 72”L

PART# 396-001001-00

Specifications are subject to change without notice.

Front panel monitoring and status displays

Real panel includes electrical video input, analog or AES audio inputs and SFP transceiver cage AR206-008070-C00_F

Output format Input format Input amplitude Input gain range Input common mode range Input common mode rejection (0 to 5.5 MHz) Input impedance Input return loss (0 to 5.5 MHz) Freq amplitude response NTSC to 4.5 MHz NTSC to 5.0 MHz PAL to 4.8 MHz PAL to 6.0 MHz Differential gain Differential phase Line time distortion Chroma-luma gain Chroma-luma delay Signal to noise, weighted

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 17

Simplifying Video Transport

FEATURES Single card SDI to composite video and analog audio conversion with optical receiver/repeater Convert SDI (SMPTE 259M) to composite video • NTSC or PAL • Analog composite 75ohm video output BNC • 10-bit component digital 525/625 line to NTSC-M or PAL- B/G conversion • Composite 12-bit processing Convert SDI to analog or AES audio • SMPTE 272M-ABC audio de-embedding with 24-bit audio conversion • Balanced analog audio outputs (4) • Balanced AES audio outputs (2) Optical transport of: • Analog video and audio • 1.485Gb/s HD-SDI (SMPTE 292M) • 270Mb/s • SD-SDI (SMPTE 259M-C, ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Artel 270 Optical to optical repeater Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (Channels 27-61) Interoperation with • Other DigiLink modules • DigiLink 1220 /2701 • Other non-scrambled or non-dithered SDI optical transmitters and receivers Multiple monitoring options • Front panel monitor (mini 75ohm SMB) selectable between: • NTSC or PAL (post-conversion) • SDI (pre-conversion) • Front and rear panel status LEDs Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

SDI to Composite Video (NTSC/PAL) Analog Audio Conversion with Optical Receiver/Repeater [DLC170DA]

DigiLink Video Transport System

The DLC170DA converts optically received SDI to composite analog video (NTSC or PAL) and analog or AES audio. Used with the DLC170AD, the design insures full TV-1 RS250-C “short haul” analog performance over a true SMPTE 259M SD-SDI optical transport link. Additionally, it can be used as an optical receiver for all digital signals from 19.39 ATSC to 1.485Gb/s HD-SDI making the DLC170DA ideal for the eventual conversion from analog to digital video transport. The innovative module uses advanced video and audio processing for exceptional quality conversion of SDI (SMPTE 259M) to composite video and analog audio. It accepts a 270Mb/s 525/625 line SDI input from either the optical SFP receiver or the backplane, then converts it to composite analog and audio signals. The received optical signal can be directed to the backplane for additional channel groups to be processed by other cards in the DigiLink chassis. Audio embedded per SMPTE 272M levels A, B, and C can be extracted as either four balanced analog audio channels or two stereo AES digital audio streams. A front panel video monitor with analog or digital selector switch allows the incoming digital (with embedded audio) or composite analog output to be monitored using conventional digital/analog video equipment.

DLC170DA SDI to NTSC/PAL and Analog Audio

Audio CH 1 Audio CH 2 Audio CH 3 Audio CH 4

AES Decode Audio De-Embed

SDI to NTSC/PAL

Internal SFP

Input Select

Format Classifiction

AES Decode

HD ASI SDI

Output Select

Video Out Front Mini SMB Internal

SDI to Composite Video (NTSC/PAL Analog Audio Conversion with Optical Receiver/Repeater [DLC170DA] APPLICATIONS NTSC/PAL Video-over-Fiber

NTSC/PAL Video-over-Fiber with Repeater

NTSC/PAL ANALOG AUDIO

NTSC/PAL DLC170AD

DLC170DA

ANALOG AUDIO

NTSC/PAL ANALOG AUDIO

NTSC/PAL DLC170AD

DLC170DA

DLC103

ANALOG AUDIO

Convert SDI to NTSC/PAL NTSC/PAL SD

DLC170AD

ANALOG AUDIO

SPECIFICATIONS SDI-to-Analog Video Conversion (6) Output format Composite Video Output amplitude Output impedance Output return loss (0 to 5.5 MHz) Freq amplitude response NTSC to 4.5 MHz NTSC to 5.0 MHz PAL to 5.5 MHz PAL to 6.0 MHz Differential gain Differential phase Line time distortion Chroma-luma gain Chroma-luma delay Signal to noise, weighted

Environmental SMPTE-170M NTSC-M or ITU-R BT.624-4 PAL-B/G 1 V p-p nominal 75ohm >30 dB, 75ohm <0.10 dB <0.10 dB <0.10 dB <0.10 dB <1.0% <0.7 degrees <1.0% <±2% <5ns >67 dB

SDI Audio-to-Analog Audio Conversion (6) Output signal Output impedance Nominal (test) level Maximum level (clip) Insertion gain Freq amplitude response (20 Hz to 20 kHz) THD+N (20-20k @ +18 dBm) SNR (weighted) Crosstalk @10kHz Audio to video lead/lag

Balanced Analog (1) < 50ohm (2) 18 dBm (3) +10 to +24 dBm (4) ±0.25 dB (5) ±0.3 dB 0.01% >95 dBA 70 dB <2 ms

Ambient operating temperature Ambient storage temperature Relative humidity Power dissipation

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) 10 watts

Physical Dimensions

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Optical Interface Artel Video SFP

See SFP specification sheet

Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 Ordering Information DLC 170DA Function Module MODEL DLC170DA

DESCRIPTION SDI to Analog Conversion and Optical Transport

SFP Optics

See optics compatibility chart

PART # 390-008080-00

Monitor Cable MODEL DL100MC-72

DESCRIPTION Monitor cable, 75ohm mini-SMB to BNC, 72”L

PART # 396-001001-00

Specifications are subject to change without notice.

(1) Specifications are with 48 kHz, 24-bit audio. (2) Designed to drive 600ohm loads. (3) Nominal level is +20 dBm for 0 dBFS (clipping) with performance specifications based on a +18 dBm test level. (4) User selectable maximum (0 dBFS) level in eight 2 dB steps. (5) Each end set to the same nominal 0 dBFS level. (6) Analog specifications based on end-to-end performance with DLC170AD. Front panel monitoring and status displays

SDI-Mode Input/output bit rate 270Mb/s ±100ppm BER 10-13@270Mb/s Output jitter <500ps I/O connectors BNC female / 75ohm I/O levels conforms to SMPTE 259M (1) Specifications are with 48 kHz, 24-bit audio SMPTE 272M-C embedded audio.

Rear panel includes electrical digital or analog video output, analog or AES audio outputs and SFP transceiver cage

Output signal Output format Output impedance

Balanced digital (1) AES3-2003 compliant 110ohm

AR206-008080-B00_F

AES Audio Output

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 19

Simplifying Video Transport

FUNCTIONS

Aggregate up to nine 10/100/1000 Ethernet links Non-blocking 18 Gigabit of switching capacity Provides Optical or Electrical Transport of • 10Base-T • 100Base-TX • 1000Base-T • Ethernet standard FEATURES Supports all types of Ethernet traffic • 10/100/1000 auto negotiate • Auto MDI/MDI-X • Auto full-duplex and half-duplex • V-Lan compatibility

Ethernet Aggregator and Optical Transceiver [DLC205]

DigiLink Video Transport System

The DLC205 is a flexible, non-blocking Ethernet Aggregator supporting up to 9 ports of 10/100/1000 traffic with optical connectivity. The innovative design of the DLC205 enables users to aggregate 9 channels, 5 external and 4 internal, of 10/100/1000 Ethernet traffic for transport across electrical or optical networks, all in a low cost, single slot DigiLink module. The module is fully nonblocking with a total capacity of 18 Gigabits of traffic and each port independently supports 10/100/1000 Ethernet. The four internal ports can be linked to other modules in a DigiLink chassis to provide internal Ethernet connectivity eliminating the need of external cabling. Unlike more complicated designs that require dedicated trunking modules and switching matrixes, the DLC205 is a simple Ethernet aggregator compatible with all DigiLink chassis providing a simple, reliable, and low cost solution for transporting video centric traffic and chassis management across Ethernet networks.

Spanning Tree redundant path protection Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (Channels 27-61) • DWDM ITU G.694.1 (Channels 21-60) Front and rear panel status LEDs • Major/minor alarms • Link status • Activity

DLC205 10/100/1000 Ethernet Aggregation

Statistics per RFC 2819 Standard Simple and rugged design • Plug and play design requires no pre-deployment configuration • Monitor, manage, and review statistics using DigiLink Manager or SNMPv2 • NEBS Level 3 Certified ensures reliable operation in harsh environments

SFP SFP

Internal A Internal B

10/100/1000 Ethernet Switch

RJ-45

Internal C

RJ-45

Internal D

RJ-45

A B Internal 10/100/1000 C

APPLICATIONS

DLC205

FGH I

External 10/100/1000

FGH I

External 10/100/1000

DLC205

External 10/100/1000

A E

B Internal 10/100/1000 C

Internal 10/100/1000

GH I

FGH I

DLC205

FGH I

A B C D

B Internal 10/100/1000 C

A B C D

DLC205

Internal 10/100/1000

10/100/1000 Ethernet Transport with Spanning Tree Protection

10/100/1000 Ethernet Transport

DLC205

Ethernet Aggregator and Optical Transceiver [DLC205]

B Internal 10/100/1000 C

DLC205

D FGH I

FGH I

External 10/100/1000

A B C D

E F

DLC205

A B C D

Internal 10/100/1000

GH I

External 10/100/1000

Internal 10/100/1000

10/100/1000 Ethernet Transport with Spanning Tree Protection SPECIFICATIONS A

Ambient storage temperature Relative humidity G H I Power dissipation (watts) External Physical 10/100/1000 Dimensions Weight

E F

E DLC205 F 50°C 0 to

A B C D

Internal 10/100/1000

-40 to 80°C 10 to 95% G (non-condensing) H I < 10 Watts External 10/100/1000 0.8” x 5” x 10.8” (1 slot in DigiLink chassis) <2 pounds, (1kg)

Interface External Electrical External SFP Internal Data Rates

Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 Ordering Information MODEL DLC205

DESCRIPTION 9 Port 10/100/1000 Ethernet Aggregator

PART # 390-008105-00

SFP Optics See optics compatibility chart Specifications are subject to change without notice.

Rear (3) RJ-45 2 (Optical or RJ-45) 4 to other modules in DigiLink Chassis 10/100/1000 Ethernet

Front Panel

DLC205

Rear Panel AR206-008105-B00_B

Environmental B Internal DLC205 10/100/1000 C Operating Temperature

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 21

270Mb/s Digital Video 4-to-1 TDM Multiplexer with Optical Transmitter/Receiver/Repeater [DLC274]

Simplifying Video Transport

DigiLink Video Transport System

FEATURES Single slot card set Transport four 270Mb/s video circuits on a single optical wavelength • Support any combination of: • SD-SDI (SMPTE 259M-C, ITU 656) • SDTI (SMPTE 305M) • DVB-ASI • Other 270Mb/s services • Use with DLC170 for composite analog transport • Full reclocking removes jitter from SDI Industry-standard 1.485Mb/s output Space efficient • Utilizes one slot in the DigiLink chassis • Transports up to 16 video circuits per rack unit

The DLC274 utilizes Time Division Multiplexing (TDM) to combine four independent 270Mb/s video signals into one optical channel.

Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (Channels 27-61) • DWDM ITU G.694.1 (Channels 21-60)

The DLC274M and DLC274D provide a space efficient and cost-effective method of transporting up to four 270Mb/s digital video services over a single optical wavelength. Services can be any combination of 270Mb/s video signals including SDI, SDTI, and DVB-ASI. Optical regeneration or repeating is accomplished using the DLC274D which includes drop and continue capabilities, DLC103, DLC300, or any other system capable of repeating a 1.485Gb/s signal. Using industry standard 1310nm, 1550nm, CWDM, or DWDM Small Form-Factor Pluggable (SFP) optics the DLC274 enables transport of up to 160 270Mb/s circuits over a single fiber.

Multiple monitoring options • Switch selectable front panel monitor of individual channels (mini 75ohm SMB) • Front and rear panel status LEDs • Loss of video (individual channels) • Loss of optical input • Laser (SFP) fail Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

DLC274D 4 Channel 270Mb/s Digital Video DeMultiplexer and Repeater BNC A BNC B

DLC274M 4 Channel 270Mb/s Digital Video Multiplexer

BNC C BNC D

BNC A Internal BNC B Internal BNC C Internal BNC D

Input Select

DLC274M

Input Select

TDM De-Mux

Internal B Internal C Internal D

SFP TDM Mux 1.485G

Internal

Monitor Select

Front Mini-SMB

Repeater

Input Select

Monitor Select

Internal A SFP

Front Mini-SMB

SD ASI

B C D

DLC274M

DLC274D

B C D

SD ASI

270Mb/s Digital Video 4-to-1 TDM Multiplexer withFour Channels of 270Mb/s Digital Video-over-Fiber with Repeater A Optical Transmitter/Receiver/Repeater [DLC274] DLC103 B SD ASI

APPLICATIONS

A B C D

DLC274M

DLC274D

DLC300

DLC274D

A B C D

SD ASI

DLC274D

A B C D

SD ASI

Four Channels of 270Mb/s Digital Video-over-Fiber drop and continue

Four Channels of 270Mb/s Digital Video-over-Fiber using TDM SD ASI

DLC274M

C D

A B C D

SD ASI

A B C D

DLC274M

DLC274D A BCD

SD ASI

Four Channels of 270Mb/s Digital Video-over-Fiber with Repeater SD ASI

A B C D

DLC274M

DLC103 DLC300

DLC274D

A B C D

Four Channels 270Mb/s Digital Video using TDM over managed optical network

SD ASI

A B C D

MANAGED OPTICAL NETWORK

DLC274M

DLC274D

A B C D

SD ASI

Four Channels of 270Mb/s Digital Video-over-Fiber drop and continue

Environmental

DLC274D

A B C D

SD ASI

A BCD

Regulatory Conformance

SD ASI Operating temperature

0 to 50°C Ambient storage -40 tonetwork 80°C Four Channels 270Mb/s temperature Digital Video using TDM over managed optical Relative humidity 10 to 95% (non-condensing) A Power dissipation MANAGED <10 watts A B SD C Physical ASI

DLC274M

OPTICAL NETWORK

DLC274D

Dimensions 0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

B C D

Optical Interface Artel Video SFP

See SFP specification sheet

Electrical Interface 270Mb/s signal formats - SD-SDI (SMPTE 259M-C, ITU 656) - SDTI (SMPTE 305M) - DVB-ASI - Others 270Mb/s services (+100ppm) Signal polarity Non Inverting Channels 4 Connectors Input (4) BNC 75ohm (DLC274M) Output (4) BNC 75ohm (DLC274D) Monitor mini 75ohm SMB Return loss >15 dB, 5-270 MHz

Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022, FCC Part 15 (Class A), CISPR 22 Ordering Information SD ASI

DLC274 Function Module MODEL DLC274M DLC274D

DESCRIPTION 270Mb/s SDI/ASI video 4-to-1 TDM multiplexer 270Mb/s SDI/ASI video 1-to-4 TDM de-multiplexer

SFP Optics

PART # 390-008020-00 390-008030-00

See optics compatibility chart

Monitor Cable MODEL DL100MC-72

DESCRIPTION Monitor cable, mini 75ohm SMB to BNC, 72”L

PART # 396-001001-00

Specifications are subject to change without notice.

Front panel monitoring and status displays

Rear panel includes four BNC electrical connections and SFP transceiver cage AR206-008020-B00_F

A B DLC274M C D SPECIFICATIONS

SD ASI

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 23

Simplifying Video Transport

3G-SDI Multi-Rate Digital Video Optical Transmitter/ Receiver/Repeater [DLC300] DigiLink Video Transport System

FEATURES Single card configurable as: • Transmit (electrical to optical) • Receive (optical to electrical) • Repeater (optical to optical) Automatic rate selection of all digital video formats • 2.967Gb/s 3G-SDI (SMPTE 424M) • 1.485Gb/s HD-SDI (SMPTE 292M) • 270Mb/s - SD-SDI (SMPTE 259M-C, ITU 656) - SDTI (SMPTE 305M) - DVB-ASI - Artel 270 • 19.39Mb/s ATSC (SMPTE 310M) Dual SFPs for route diversity • Operates with one or two SFPs • Separate fault alarms for each SFP • Receive via primary or secondary SFP • Automatic switchover upon loss of signal • User selectable reversion to primary SFP Optional dithering of all SDI formats • Dithering per SMPTE EG-34 Convert ATSC to DVB-ASI • Transmitter only Interoperates with • Other DigiLink modules • ITU 694.1 or 694.2 optical multiplexers Flexible multi-purpose repeater for: DLC103, DLC150E, DLC170, DLC274, DV6000, DL1220, DL2701 Non-video standby signal on loss of video input Video test or standby signal generator for SDI formats Externally accessible SFP transceiver optics • Optical budget to 33dB • WDM (1310nm, 1550nm) • CWDM ITU G.694.2 (Channels 27-61) • DWDM ITU G.694.1 (Channels 21-60) Inputs/outputs • Optical via SFPs • Electrical via 75ohm BNC • Input from and output to other modules in DigiLink chassis (via backplane) Multiple monitoring options • Front panel monitoring of transported signal • Front and rear panel status LEDs Remote management via DigiLink Manager • No external software required • HTTP or SNMP v2 • Monitor • Configure • Upgrade firmware

The DLC300 is a flexible fiber optic transport module for all digital video formats from 19.39Mb/s (ATSC) to 2.97Gb/s (3G-SDI). The DLC300 is a single-module, user configurable to function as a transmitter, receiver, or repeater and supports route diversity as well as ATSC to DVB-ASI conversion. The DLC300 incorporates numerous features in a flexible, easy-to-deploy and configure module with unparalleled quality and reliability. The module optically transports all digital formats from 19.39Mb/s ATSC to 3G-SDI (SMPTE 424M). To minimize inventory costs and simplify deployment, it can be configured as a receiver, transmitter, or repeater. For route diversity and optical flexibility the DLC300 also features dual optical SFP modules available in WDM, CWDM, or DWDM optical wavelengths. To transport across metro optical amplified networks, dithering of all SDI formats has been included, as well as conversion from SMPTE 310M to DVB-ASI. Cost-effective, flexible, and reliable, the DLC300 continues Artel’s tradition of making the world’s most innovative and reliable video over optical transport hardware.

DLC300 Digital Video Transmitter /Receiver/Repeater with Redundant Optics Transmitter Mode BNC In Internal

Input Select

SMPTE to ASI Signal Classification Dither Video Standby

Output Select

SFP 1 SFP 2

Keep Alive Signal Front Mini-SMB

Receiver Mode SFP 1 SFP 2

Input Select

Signal Classification

SDI Un-Dither

Output Select

BNC out Internal Front Mini-SMB Repeated Repeated

3G-SDI Multi-Rate Digital Video Optical Transmitter/ Receiver/Repeater [DLC300] APPLICATIONS Digital Video-over-Fiber 3G HD SD ASI ATSC

Single Channel Digital Video over managed optical network

DLC300

3G HD SD ASI ATSC

DLC300

3G HD SD ASI ATSC

DLC300

Digital Video-over-Fiber with Repeater 3G HD SD ASI ATSC

DLC300

MANAGED OPTICAL NETWORK

DLC300

3G HD SD ASI ATSC

Format Conversion ATSC to SDI

3G HD SD ASI ATSC

ATSC

DLC300

ASI

Digital Video over Fiber with Redundant path Protection 3G HD SD ASI ATSC

DLC300

3G HD SD ASI ATSC

SPECIFICATIONS Environmental

SDI Signal Processing (3G–SDI, HD-SDI and SD-SDI)

Operating temperature Ambient storage temperature Relative humidity Power dissipation

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) 8.4 watts with one SFP

Optical Interface Artel Video SFP

See SFP specification sheet

Regulatory Conformance

Physical Dimensions

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Electrical Interface Signal Formats 2.967Gb/s 3G-SDI (SMPTE 424M) 1.485Gb/s HD-SDI (SMPTE 292M) 270Mb/s SD-SDI (SMPTE 259M-C, ITU 656) SDTI (SMPTE 305M) DVB-ASI ARTEL 270 19.39Mb/s ATSC (SMPTE 310M)) Signal polarity Channels Connectors Input (1) Output (1) Monitor Return loss (input, output, monitor) Cable equalization for Belden 1694A Optical Protection Modes

DESCRIPTION PART # 3G-SDI Multi-Rate Digital Video 390-008120-00 Transmitter/Receiver/Repeater

Monitor cable, 75ohm mini-SMB to BNC, 72”L

396-001001-00

Specifications are subject to change without notice.

Non inverting 1-transmit, receive or repeat BNC 75ohm BNC 75ohm mini 75ohm SMB >15 dB, 5-1485 MHz >10dB, 1486-2967MHz 0 to 250 meters (270Mb/s) 0 to 140 meters (1.485Gb/s) 0 to 100 meters (2.967Gb/s)

Front panel monitoring and status displays

Rear panel Includes electrical input or output and dual SFP transceiver cages

625i/25 1080i/25 1080p/25

AR206-008120-C00_F

525i/29.97 1080i/29.97 1080p/29.97

Ordering Information DLC300 Function Module MODEL DLC300 Monitor Cable DL100MC-72

SDI test or standby signal formats

Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22

SFP Optics See optics compatibility chart

Transmit Transmit same signal on each SFP Receive Primary and secondary SFP sockets Automatic switchover upon loss of signal User selectable reversion to primary SFP SD-SDI HD-SDI 3G-SDI

Optional LSB dithering per SMPTE EG-34

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 25

Simplifying Video Transport

FEATURES

Single-module transceiver for SD-SDI and DVB-ASI over Gig-E • Fully transparent carriage of SDI and SDTI • Includes all SDI and SDTI ancillary information • DVB-ASI stream rates from <20 Mb/s to >200 Mb/s • Supports 188-byte and 204-byte DVB-ASI packets • Provisionable limits on bandwidth for DVB-ASI Four independent channels: two transmit, two receive Unicast or multicast IP video streams Standards-based encapsulation and Forward Error Correction • DVB-ASI • SMPTE 2022-2 Encapsulation • SMPTE 2022-1 FEC • SDI • SMPTE 2022-6 Encapsulation • SMPTE 2022-5 FEC • FEC recovers lost, errored, or delayed packets • Withstands burst outages in excess of 3 mS • Row and column FEC supported Externally accessible SFP transceivers • Optical budget to 33 dB • WDM (1310 nm, 1550 nm) • CWDM ITU G.694.2 (Channels 27-61) • DWDM ITU G.694.1 (Channels 21-60) • Electrical to RJ-45 Ethernet Front panel monitoring of active video signals Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2 • Monitor • Configure • Upgrade firmware

DVB-ASI and SD-SDI Video-Over-IP Gateway [DLC410]

DigiLink Video Transport System

The DLC410 greatly expands the DigiLink video platform capabilities to include SMPTE standards-based Video-Over-IP transport for both DVB-ASI and SD-SDI formats. The module is capable of transporting four channels (two in each direction) of DVB-ASI or SD-SDI over a gigabit Ethernet IP network connection. Based on SMPTE 2022 standards for encapsulation and Forward Error Correction (FEC), the DLC410 enables SDI and ASI to be reliably transported across managed IP networks. Two independent video channels in each direction can be transported over a single Gig-E connection. SDI video is transported in its entirety, including all ancillary data. ASI video streams from less than 20 Mb/s to over 200 Mb/s are supported and can be rate limited. The DLC410 FEC enables the recovery of lost, errored, or delayed IP packets and can withstand burst outages in excess of 3 mS. Access to the IP network is through rear accessible field replaceable SFPs either optically in WDM, CWDM , and DWDM wavelengths or electrically via an RJ-45 SFP.

DLC410 DVB-ASI and SD-SDI Dual Bi-Directional Video-over-IP Gateway BNC In A Internal BNC In B Internal

Input Select

IP Encap

FEC Encode

IP Decap

FEC Process

Ethernet MAC

BNC out A BNC out B Internal Internal

Monitor Select

SFP

Front HD-BNC

DVB-ASI and SD-SDI Video-Over-IP Gateway

Four channel bi-Directional SDI or ASI over IP

[DLC410]

Four channel bi-Directional SDI or ASI over IP SD ASI

A B C D

SD ASI

APPLICATIONS

DLC410

A B C D

DLC410

A B C D

SD ASI

SDI or ASI over IP with Multicasting

DLC410

A B C D

SD SD ASI ASI

DLC410

A B C D

SD ASI

A B C D

DLC410

SD ASI

SDI or ASI over IP with Multicasting SD ASI

A B C D

DLC410

A B

SD ASI

NTSC/PAL over IP DLC410

A B

SD ASI

NTSC/PAL

A B C D

DLC170AD

DLC410

DLC170DA

A B C D

NTSC/PAL

NTSC/PAL over IP A B DLC170AD C SPECIFICATIONS D

NTSC/PAL

DLC410

DLC170DA

Network Interface - Optical Type SFP Optical connectors LC Format 1000Base-LX, 1000Base-ZX Network Interface - Electrical Type SFP Connector RJ-45 Data rate 1000 Mb/s Format 1000Base-T Video Interface Formats SD-SDI (SMPTE 259M) SDTI (SMPTE 305M) DVB-ASI Channels 2 input and 2 output

NTSC/PAL

Physical Dimensions

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022, FCC Part 15 (Class A), CISPR 22 Ordering Information DLC410

Function Module

MODEL DLC410

DESCRIPTION PART # DVB-ASI and SD-SDI Video 390-008410-00 Over IP Gateway

SFP Optics

See optics compatibility chart

Monitor Cable

Electrical Interface Input Output Monitor (front) Return loss Cable equalization for Belden 1694A type cable

A B C D

(2) BNC 75 ohm (2) BNC 75 ohm HD-BNC 75 ohm >15 dB, 5-270 MHz 0 to 350 meters (270 Mb/s)

MODEL DL100HDMC-72

DESCRIPTION PART # Monitor cable, HD-BNC to BNC, 72” long 396-001010-72

Specifications are subject to change without notice.

Environmental Operating temperature 0 to 50°C Ambient storage temperature -40 to 80°C Relative humidity (non-condensing) 10 to 95% Power dissipation 10 watts Front panel monitoring and status displays

AR206-008410-D00_F

Rear panel includes 2 input and 2 output BNCs plus SFP cage

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 27

Simplifying Video Transport

FUNCTIONS

Ethernet transport of HD-SDI (SMPTE 292M) Single modules user configurable as a Transmitter or Receiver Fully transparent carriage of HD- SDI including all ancillary data FEATURES Standards-based encapsulation and Forward Error Correction • SMPTE 2022-6 IP Encapsulation • SMPTE 2022-5 FEC recovers lost, damaged, or delayed packets Flexible user configurable FEC and Buffering setting • Selectable transmitter Row and column Forward Error Correction settings • Selectable receiver buffering • Designed to withstands burst outages in excess of 3 mS

HD-SDI Video Over IP Gateway [DLC450]

DigiLink Video Transport System

Designed as a cost-effective solution for transport of uncompressed HD-SDI over managed Ethernet IP networks, the DLC450 utilizes SMPTE 2022-5/6 IP Encapsulation and Forward Error Correction (FEC) algorithms to ensure reliable, error-free transport and compliance with industry standards. The DLC450 is a cost effective DigiLink compatible module enabling a single channel of uncompressed HD-SDI (SMPTE 292M) to be transported over a managed Ethernet network. Integrating seamlessly within the DigiLink platform, the DLC450 is customer configurable via DigiLink Manager or via SNMPv2 as either a transmitter or receiver. In transmitter mode, the DLC450 packetizes the video to SMPTE 2022-6 encapsulation standard and provides users with flexible SMPTE 2022-5 FEC configurations to maximize reliability and minimize latency and overhead. In receiver mode, its robust multi-pass FEC correction algorithm and user configurable packet buffering enable reliable performance over less than ideal Ethernet links. The DLC450 sets the bar for reliable, low cost, and easy to configure HD-SDI transport over IP.

Supports unicast or multicast streaming Externally accessible SFP+ transceivers • WDM (1310 nm, 1550 nm) • CWDM ITU G.694.2 (Channels 27-61) • DWDM ITU G.694.1 (Channels 21-60) • Electrical to RJ-45 Ethernet

DLC450 HD-SDI Over IP Gateway Transmitter

Front panel HD-BNC monitor Configure, monitor and manage via on-board DigiLink Manager or SNMPv2 Low power design consumes a single function slot in a DigiLink chassis

BNC In Internal

IP Encapsulation

Input Select

FEC

SFP + 10 Gig-E Internal A Front HD-BNC

Receiver SFP + 10 Gig-E Internal

Input Select

FEC Processing

IP De-Encapsulation

BNC Out Internal Front HD-BNC

HD-SDI Video Over IP Gateway [DLC450] APPLICATIONS HD over 10G Ethernet HD

DLC450

HD HD over 10G Ethernet with Multicasting

DLC450

SPECIFICATIONS Regulatory Conformance

Environmental Operating Temperature Ambient storage temperature Relative humidity Power dissipation (watts)

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) 10 Watts

Physical Dimensions Weight

0.8” x 5” x 10.8” (1 slot in DigiLink chassis) <2 pounds, (1kg)

Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 Ordering Information MODEL

DESCRIPTION

PART #

DLC450

HD-SDI Video Over IP Gateway

390-008450-00

SFP+ Optics

See optics compatibility chart

Video Interface

Monitor Cable

Signal Formats HD-SDI (SMPTE 292M)

MODEL DL100HDMC-72

Electrical Video Interface Input Output Return Loss Cable Equalization for Belden 1694A type cable:

Specifications are subject to change without notice.

Rear BNC 75ohm Rear BNC 75ohm Front HD-BNC 75ohm >15 dB, 5-1485 MHz

DESCRIPTION Monitor Cable, 75-ohm HD-BNC to BNC

PART # 396-001010-72

0 to 140 meters (1.485 Gb/s)

Network Interface Ethernet SFP+ LC 10 Gig-E

DLC450 front panel video and data I/O and status LEDs

DLC450 rear panel video and data I/O and status LEDs

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 29

AR200-008450-B00_A

Type Optical Connectors Format

HD-SDI JPEG2000 Compression with DVB-ASI Encapsulation Simplifying Video Transport

FUNCTIONS

Compress HD-SDI (SMPTE-292M ) into JPEG2000 Encapsulate with audio and ancillary data into DVB-ASI Single module user configurable as a Encoder or Decoder FEATURES High Quality JPEG2000 Compression • ISO/IEC 15444-1 Compliant Encoding • 10-bit Resolution • Variable compression from 80-180Mb/s DVB-ASI Encapsulation of Video, Audio, and Ancillary data • Industry Standard JPEG2000 into ASI encapsulation • Supports up to 16 channels of 24-bit audio • Includes Time Code, Subtitling and other ancillary data Compact, flexible, and low power • Uses a single function slot in DigiLink chassis • Single module user configurable, and encoder or decoder • Integrated into DigiLink platform enabling multiple transport options • Consumes less than 10 Watts Simplified, reliable design • Configure via HTTP or SNMPv2 • NEBS Level 3 Certified ensures reliable operation in harsh environments

[DLC610]

DigiLink Video Transport System

The DLC610 is a low cost DigiLink based module enabling a single HDSDI signal to be compressed via JPEG2000 then encapsulated into DVBASI including Audio and Ancillary data for transport across DVB- ASI compatible networks. The DLC610 module is a user programmable JPEG2000 Encoder or Decoder featuring low latency with industry standard ASI encapsulation. It is an ideal solution for transporting high quality HD-SDI signals across DVB-ASI compatible networks. The DLC610 utilizes the IntoPix® compression core to compress HD-SDI into an 80 to 180Mb/s JPEG2000 video codestream and then, encapsulated with all audio and ancillary data, into DVB-ASI per industry standards. The resulting DVB-ASI stream is now ready to be transported via fiber links, Gig-E, and/or optical networks for decoding and delivery using another DLC610 or other industry standard JPEG2000 decoders. The flexible design enables the DLC610 to be used as a low-cost standalone solution for integration into industry standard ASI equipment, or work in the highly integrated DigiLink platform with its internal routing of video and Ethernet traffic for transport, trunking, and distribution.

DLC610 HD-SDI JPEG2000 Compression with ASI Encapsulation Encoder BNC In Internal

Input Select

Video DeEmbed

Video Encode AES Ancillary Data

MPEG-2 TS Encapsulation

ASI Encapsulation

BNC Out Internal Front HD-BNC

Decoder BNC In Internal

Input Select

ASI De-Encapsulate

MPEG-2 TS De-Encapsulation

Video Decode AES Ancillary Data

Video Embed

BNC Out Internal Front HD-BNC

HD-SDI JPEG2000 Compression with DVB-ASI Encapsulation

[DLC610]

APPLICATIONS

HD to JPEG2000 Compression and ASI Encapsulation

ASI (JPEG2000)

DLC610

ASI (JPEG2000)

DLC610

HD over Gig-E HD

DLC610

DLC410

DLC610

SPECIFICATIONS Environmental Operating Temperature Ambient storage temperature Relative humidity Power dissipation (watts)

Regulatory Conformance 0 to 50°C -40 to 80°C 10 to 95% (non-condensing) 10 Watts

Physical Dimensions Weight

0.8” x 5” x 10.8” (1 slot in DigiLink chassis) <2 pounds, (1kg)

Video Interface Signal Format in Signal Format out

HD-SDI (SMPTE 292M) DVB-ASI (270Mb/s)

Compliance:

NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22

Ordering Information MODEL DLC610

DESCRIPTION HD-SDI JPEG2000 Encoder/Decoder

PART # 390-008250-00

DESCRIPTION Monitor Cable, 75-ohm HD-BNC to BNC

PART # 396-001010-72

Monitor Cable MODEL DL100HDMC

Specifications are subject to change without notice.

Compression Format JPEG2000 Standard ISO/IEC 15444-1 Capacity 213Mb/s including audio and ancillary data Range 0-180Mb/s of Video Electrical Interface Input

Rear BNC 75ohm

Output

Rear BNC 75ohm Front HD-BNC 75ohm

Return Loss

>15 dB, 5-1485 MHz

Cable Equalization for Belden 1694A type cable: 0 to 140 meters (1.485 Gb/s) Internal input/output to DigiLink chassis DLC610 front panel video I/O and status LED

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 31

AR206-008250-B00_A

DLC610 rear panel video I/O and status LED

Simplifying Video Transport

FUNCTIONS

Monitor and Manage DL4000 Chassis Aggregate up to nine 10/100/1000 Ethernet links Non-blocking 18 Gigabit of switching capacity Provides Optical or Electrical Transport of • 10Base-T • 100Base-TX • 1000Base-T • Ethernet standard FEATURES In-band management of DL4000 chassis Supports all types of Ethernet traffic • 10/100/1000 auto negotiate • Auto MDI/MDI-X • Auto full-duplex and half-duplex • V-Lan compatibility

Ethernet Aggregator and Optical Transceiver with On-Board Chassis Management [DLM205]

DigiLink Video Transport System

The DLM205 combines a 9 port non-blocking Ethernet switch and aggregator with DL4000 chassis management capabilities. The innovative design of the DLM205 enables users to manage and monitor DL4000 chassis as well as aggregate 9 channels, 5 external and 4 internal, of 10/100/1000 Ethernet traffic for transport across electrical or optical networks, all in a low cost, single slot DigiLink module. The module is fully non-blocking with a total capacity of 18 Gigabits of traffic plus chassis management and each port independently supports 10/100/1000 Ethernet. The four internal ports can be linked to other modules in a DigiLink chassis to provide internal Ethernet connectivity eliminating the need of external cabling. Unlike more complicated designs that require dedicated trunking modules and switching matrixes, the DLM205 is a simple Ethernet aggregator compatible with all DigiLink chassis. When used in a DL4000 chassis an additional channel is enabled that includes capabilities to manage, monitor, configure a chassis via DigiLink Manager HTTP browser based EMS or SNMP. The DLM205 provides a simple, reliable, and low cost solution for transporting video centric traffic and chassis management across Ethernet networks.

DLM205 Ethernet Aggregation with Embedded DigiLink Manager

SFP

DigiLink Manager

SFP

Internal A 10/100/1000 Ethernet Switch

Statistics per RFC 2819 Standard

Internal B

Simple and rugged design • Plug and play design requires no pre-deployment configuration • Monitor, manage, and review statistics using DigiLink Manager or SNMPv2 • NEBS Level 3 Certified ensures reliable operation in harsh environments

Internal C

RJ-45

Internal D

RJ-45

10/100/1000 Ethernet Transport with in-band DigiLink Manager A B C D

A B Internal Ethernet Aggregator and Optical Transceiver with On-Board10/100/1000 Chassis Management C DLM205 E D [DLM205]

DigiLink Manager

APPLICATIONS 10/100/1000 Ethernet Transport with in-band DigiLink Manager

DigiLink Manager

Internal 10/100/1000 DigiLink

A B C D

DLM205

FGH I

External 10/100/1000

DLM205

Manager SPECIFICATIONS FGH

Environmental

A B C D

External 10/100/1000

Operating Temperature Ambient storage temperature Relative humidity Power dissipation (watts)

Internal 10/100/1000

DigiLink Manager

DLM205

A B C D

FGH I

External 10/100/1000

0 to 50°C -40 to 80°C 10 to 95% (non-condensing) < 10 Watts

Physical Dimensions Weight

0.8” x 5” x 10.8” (1 slot in DigiLink chassis) <2 pounds, (1kg)

Interface External Electrical External SFP Internal Data Rates

Rear (3) RJ-45 2 (Optical or RJ-45) 4 to other modules in DigiLink Chassis DL4000 Chassis Management 10/100/1000 Ethernet

A B C D

DLM205

FGH I

External 10/100/1000

DLM205

Internal 10/100/1000 DigiLink Manager

DLM205

FGH I

External 10/100/1000

A B C D

Internal 10/100/1000 DigiLink Manager

Regulatory Conformance Compliance: NEBS Level 3, CSA 60950, EN60950, EN55022 FCC Part 15 (Class A), CISPR 22 Ordering Information MODEL DLM205

DESCRIPTION 9 Port 10/100/1000 Ethernet Aggregator and Chassis Management

PART # 390-008106-00

SFP Optics See optics compatibility chart Specifications are subject to change without notice.

Front Panel

DLM205

Rear Panel AR206-008106-B00_B

Internal 10/100/1000

SFP Optics

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 33

Simplifying Video Transport

FEATURES

Single-module provides generation and verification for: • 2.97Gb/s 3G-SDI (SMPTE 424M) • 1080p/59.94 • 1080p/50 • 1.485Gb/s HD-SDI (SMPTE 292M) • 1080i/59.94 • 1080i/50 • 720p/59.94 • 720p/50 • 270Mb/s SD-SDI (SMPTE 259M) • 525i/59.94 • 625i/50 • 270Mb/s DVB-ASI • 19.39Mb/s ATSC (SMPTE 310M) Video generator functions • User selectable rates and formats • SDI color bars or pathological test signals both with audio tone • Stored MPEG video stream • Automatically sequences through all selected formats • Output to two BNCs and chassis backplane

Multi-Format Digital Video Generator and Test Module [DLT710] DigiLink Video Transport System

Artel’s DLT710 is an innovative, DigLink based module for simple, automatic link verification of serial digital video formats. The singlemodule functions as both a signal generator and test monitor for 3G-SDI, HD-SDI, SD-SDI, DVB-ASI, and ATSC and is ideal for automatic verification of single or multi-format video links. A universal digital video link test and verification module, the DLT710 provides complete, one-touch “go-no-go” performance testing for all common video rates and formats. Its unique design allows for one or more formats to be selected simultaneously enabling automatic verification of multi-format video links. As a test signal generator, the DLT710 outputs a continuous video signal of a single selected format or a timed sequence through each selected format. When configured as a monitor for a single format it will continuously monitor live digital video and indicate rate and physical layer signal quality. With more than one format selected, the module automatically verifies each rate has been received. With this unique multi-purpose module, verification of a multi-service video link can be performed in less than five minutes. The DLT710 is an ideal solution for link verification of digital video circuits.

Video monitor functions • Test for EDH, CRC • Automatically detects input signal • Tests DVB-ASI and SMPTE 310 transport streams • DVB-ASI inversion detection • Detects and verifies all selected formats • Input from BNC or chassis backplane • Indicates low-level or double terminated inputs Remote management via DigiLink Manager • No external software required • HTTP or SNMPv2c • Configure, monitor • Upgrade firmware • Time-stamped event log

DLT710 Video Generator, Monitor and Test Signal Generator 3G-SDI Color Bar 3G-SDI Pathalogical HD-SDI Color Bar HD-SDI Pathalogical SD-SDI Color Bar SD-SDI Pathalogical DVB-ASI ATSC

BNC In Internal A

Input Select

BNC 1 out BNC 2 out Internal

Signal Select and Ouput Timer

Output Select

Monitor Test

DigiLink Manager

Front Mini-SMB

Multi-Format Digital Video Generator and Test Module [DLT710] APPLICATIONS Circuit Verification 3G HD SD ASI ATSC

DLT710

DLC103

DLT710

3G HD SD ASI ATSC

Circuit Analysis, Monitoring and Logging 3G HD SD ASI ATSC

DLC103

DLT710

3G HD SD ASI ATSC

• • • • • • • •

ABSENSE OR PRESENSE OF SIGNAL FORMAT TYPE FREQUENCY INPUT SIGNAL LEVEL CRC AND EDH ERRORS VALID MPEG2 TRANSPORT STREAM 8B10B CODING POLARITY INVERSION

SPECIFICATIONS Environmental

Video Electrical Interface Inputs

1 BNC 75ohm (panel) Other modules in DigLink chassis via backplane

Outputs

2 BNC 75ohm (panel) 1 mini 75ohm SMB (front panel) Other modules in DigiLink chassis via backplane

Return loss (input, output, monitor) > 15 dB 5-1485 MHz > 10 dB 1486-2970 MHz Cable equalization for Belden 1694A 0 to 50 meters Output amplitude 800mVP-p, ± 10% Rise/fall time 270Mb/s 800ps ±400 1.485Gb/s < 135ps 2.970Gb/s < 135ps Generation frequency stability ± 2.5 ppm maximum Output jitter* 270Mb/s < 500 ps p-p 1.485Gb/s <135 ps p-p 2.970Gb/s <101 ps p-p * Using color bars, per EG-33

Ambient operating temperature Ambient storage temperature Relative humidity (non-condensing) Power dissipation

0 to 50°C -40 to 80°C 10 to 95% 10 watts

Physical Dimensions

0.8” x 5” x 10.8” 1 slot in DigiLink video platform chassis

Regulatory Compliance Compliance: CSA 60950, EN60950, EN55022, FCC Part 15 (Class A), CISPR 22 Ordering Information DLT710 Digital Video Generator and Test Module MODEL

DESCRIPTION

DLT710

Multi-Format Digital Video Generator and Test Module

PART #

DLK710

Multi-Format Digital Video Generator and Test Module Travel Kit

390-008150-00 398-008150-00

DLK710 Kit Includes: • DLT710 Multi-Format Digital Video Generator and Monitor • DL4100 single slot chassis with external AC power supply • 16.68” x 13.06” x 4.37” ruggedized travel case • BNC to BNC monitor cable (2) • BNC to mini-SMB monitor cable • Screwdriver

AR206-008150-B00_E

Front panel

Rear panel includes electrical video and audio signal generator and checker, and format select switches

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 35

Simplifying Video Transport

FEATURES

Optical multiplexer features • Low optical losses • Passive design for reliability • Bi-directional • Industry standard ITU wavelengths • Industry standard LC/PC connectors • Most modules include expansion port (passes all other wavelengths) • Compatible with all DigiLink chassis (including DL4000P passive 4 slot chassis) WDM features • 1310nm and 1550nm combiner/splitters • Single or dual WDM options • External WDM conserves chassis slot • Split ratios from 50/50 to 1/99

Optical Multiplexers DWDM, CWDM and WDM Modules DigiLink Video Transport System

Artel’s DWDM, CWDM, and WDM modules create a comprehensive set of optical multiplexing solutions for the DigiLink video transport system. These modules, in conjunction with other DigiLink modules or third party equipment, allow the creation of flexible, space and fiber efficient optical networks. Artel designed its optical multiplexing products to address the issue of space and fiber constraints. For space efficiency, each module takes only one bay in a DigiLink chassis. By using ITU standard filters and optics, multi-vendor, cost-effective, and fiber efficient video and Ethernet can be created. Completely passive and designed with the latest optical filters, Artel’s DWDM, CWDM, and WDM modules are extremely reliable, cost-effective, and feature low insertion losses.

CWDM features • Industry standard ITU G.694.2 wavelengths • Optically multiplex up to 18 channels over a single fiber • 4, 8, 10, and 18 channel options • Multiple 4 channel options DWDM features • Industry standard ITU G.694.1 wavelengths • Optically multiplex up to 40 channels on a single fiber • 4,10, 20, and 40 channel options • Interconnect modules to enable 40 channels in a single 1RU chassis

Optical Multiplexers, Splitter and Combiners CH 21

1271nm 4 to 18 Channels

CWDM

5 to 40 Channels

DWDM

CH 60

1611nm

1 - 99 %

1310nm WDM

1550nm

Splitters 99 - 1 %

WDM Ordering Information and Specifications | 1310nm and 1550nm Description

Part #

# Channels

Channels

Insertion Loss

Adjacent Channel Isolation

Return Loss

DLOW1

Single WDM

390-008754-01

1310, 1550

≤1.4dB

≥ 30dB

≥ 40dB

DLOW2

Dual WDM

390-008754-02

1310, 1550

“

DLOWE

External WDM

390-008790-15

1310, 1550

“

Model #

CWDM Ordering Information and Specifications | Channels 1271 through 1611 of ITU G694.2 Part #

# Channels

Channels

Insertion Loss (±7.0 nm)

Adjacent Channel Isolation

Directivity

Return Loss

Insertion Loss Upgrade Port

DLOC4L

390-008752-00

1471, 1491, 1511, 1531

≤ 2.2dB

≥ 30dB

≥ 40dB

≤ 2.2dB

DLOC4M

390-008752-01

1511, 1531, 1551, 1571

“

DLOC4H

390-008752-02

1551, 1571, 1591, 1611

“

DLOC40

390-008752-03

1471,1491, 1591, 1611

“

390-008752-04

1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611

≤ 3.3dB

“

≤ 2.1dB

DLOC10 390-008752-10

1271,1291,1311,1331,1351, 1371,1391,1411,1431,1451

≤ 5.1dB

> 25dB

> 50dB

> 45dB

≤ 1.1dB

DLOC18

1271,1291,1311,1331,1351,1371, 1391,1411,1431,1451,1471,1491, 1511,1531,1551,1571,1591,1611

≤ 6.1dB

“

N/A

Model #

DLOC8

390-008752-18

DWDM Ordering Information and Specifications | Channels 21 through 60 of ITU G694.1 # Chans

Channels

Part #

Insertion Loss (±0.11 nm)

Adjacent Channel Isolation

Directivity

Return Loss

Uniformity

Insertion Loss Upgrade Port

DLOD421

21, 22, 23, 24

390-008762-21

≤ 2.4dB

≥ 25dB

≥ 50dB

≥ 40dB

≤ 1.0dB

≤ 1.9dB

DLOD425

25, 26, 27, 28

390-008762-25

“

DLOD429

29, 30, 31, 32

390-008762-29

“

DLOD433

33, 34, 35, 36

390-008762-33

“

DLOD437

37, 38, 39, 40

390-008762-37

“

DLOD441

41, 42, 43, 44

390-008762-41

“

DLOD445

45, 46, 47, 48

390-008762-45

“

DLOD449

49, 50, 51, 52

390-008762-49

“

DLOD453

53, 54, 55, 56

390-008762-53

“

DLOD457

57, 58, 59, 60

390-008762-57

“

DLOD1021

21-30@100GHz

390-008765-21

≤ 4.1dB

“

≤ 4.1dB

DLOD1031

31-40@100GHz

390-008765-31

“

DLOD1041

41-50@100GHz

390-008765-41

“

DLOD1051

51-60@100GHz

390-008765-51

“

DLOD2021

21-40@100GHz

390-008766-21

≤ 5.1dB

“

≤ 5.1dB

DLOD2041

41-60@100GHz

390-008766-41

“

≥ 45dB

“

DLOD4021

21-60@100GHz

390-008767-21

≤ 6.1dB

“

≥ 40dB

“

N/A

Model #

Dual Window Wide Band Optical Splitters Ordering Information and Specifications Description

Part #

DLOS2

50/50 Optical Splitter

390-008753-00

Port 1 | Ratio | Port 2 50%

50%

≤ 4.0dB

Port 1 | Insertion Loss | Port 2 ≤ 4.0dB

DLOS2-01

1/99 Optical Splitter

390-008753-01

99%

≤ 23.1dB

≤ 1.1dB

DLOS2-05

5/95 Optical Splitter

390-008753-05

95%

≤ 15.1dB

≤ 1.1dB

DLOS2-10

10/90 Optical Splitter

390-008753-10

10%

90%

≤ 12.1dB

≤ 1.5dB

DLOS2-20

20/80 Optical Splitter

390-008753-20

20%

80%

≤ 8.6dB

≤ 2.1dB

DLOS2-30

30/70 Optical Splitter

390-008753-30

30%

70%

≤ 6.6dB

≤ 2.6dB

DLOS2-40

40/60 Optical Splitter

390-008753-40

40%

60%

≤ 5.1dB

≤ 3.6dB

AR206-008799-00_D

Model #

www.artel.com | 978-263-5775 | sales@artel.com | customercare@artel.com 37

Uma publicação da