Metropolitan Custom Office Program Introduction The Custom Office Program provides the opportunity for Stickley to custom manufacture a workspace to fit your organizational needs. Using a variety of components Stickley will create a custom workspace of almost any size. The information below provides a basic guideline to assist you in creating your custom workstation.
Work Surface Layout
Straight Run
“L” Shaped
Top Depth: 20” vs. 24” • • • •
Metropolitan Office base components are manufactured at a 20” depth. 20” top depth will fit flush, front to back, with the base components. 24” top depth will fit flush with the front of the base component and overhang 4” on the back of the base component. Filler panels are available to close off each end of the workstation when using a 24” top.
Counter Top Length: 35” to 105” • • •
Counter top sections can be ordered by the inch from 35” up to 105” per section. The continuous top length must be specified. There are 3 standard top lengths: 35”, 70” and 105”. Location of wire access holes on the work surface area will be decided by the customer at the time of delivery. Two inch access holes will be bored on site by an authorized Stickley service technician or a contractor. Grommets will be supplied and installed after the wire access holes are bored.
Base / Storage Components: •
• •
These components act as storage and support mechanisms for your workstation. Individual base components can be grouped together under a common top (see page 4). Available units are influenced by the overall length of the workstation. When base units are ordered to go under the top of a work station, order as a no top (NT) option. e.g. 7658-NT Each base unit will be supplied with individual bases.
Accessory Units / Supports: •
• • • •
Depending upon the base / storage component selections, additional supports may be required. Accessory units are mounted flush with the front of the counter top, support units are mounted flush with the back of the counter top. All accessory and support units will be installed on site by an Authorized Stickley Service Technician or a Contractor. If there is 35” or more of unsupported top, Stickley suggests a base support be added. A support leg is required at the join between a straight run and corner work surface. A wire management system will be supplied with each Metropolitan office for a clean look.
Upper Bookcases / Storage Components: • • •
Upper components provide additional storage and organization space for your workstation. Available units are influenced by the overall length of the workstation. Upper units will be permanently screwed together at the factory in a length up to 105”. Units can be bolted together for knock down (KD) delivery upon request. Note installation guidelines on the following page.
Ordering: •
• •
All Metropolitan Custom Office orders require a diagram clearly illustrating the layout, overall length, components being used and the placement of the components. Please complete the Metropolitan Custom Office Order Form and submit with your order. Sample office layouts are available for reference on the following pages.
Metropolitan Custom Office Program Installation Guidelines Please read all warnings, cautions and assembly instructions thoroughly before assembling units to ensure a properly assembled & secure Metropolitan Custom Office. Fasten to Existing Wall •
Straight run and corner workstation tops must be fastened to an existing wall. Stickley recommends that the installation be completed by an Authorized Stickley Service Technician or a Contractor.
Workstations that are not supported at both ends by a desk, file or cabinet unit must be fastened to the wall. The configuration shown above will need to be installed by an Authorized Stickley Service Technician or a Contractor. This order will require a custom order form.
Workstations that are supported under two ends do not need to be installed by an Authorized Stickley Service Technician or a Contractor. The configuration shown above should be ordered through the standard credenza order format. e.g. 7665-62-65 for the upper units, 7658-59-58 for lower units.
Additional Information / Instructions: •
• • • •
Stickley recommends that the Metropolitan Office be installed by an Authorized Stickley Service Technician or a Contractor. Some assembly steps will require two people to prevent personal injury or damage to the product. Mending plates are attached to the upper units; Anti-Tip Kits may also be used to attach upper units to the wall. Shelf standards for the 7674-35 and 7674-70 must be fastened to wall studs or a solid wall. Before beginning assembly, carefully unpack and lay out all hardware and parts and match them to the part list included in the Assembly Instructions. If parts are missing or broken, contact your Authorized Stickley Dealer or Customer Service Representative.
Request for Stickley Metropolitan Office Units ONLY
IMPORTANT! Attach this form to your purchase order. Before completing, please read the information packet about the Metropolitan Custom Office Program thoroughly. Please fill in all information requested below.
Purchase Order No.:_________________________________________________ Date:____________________________________ Dealer/Showroom Name:__________________________________________ Stickley CS Rep:_________________________________ Customer Name:___________________________________________ Salesperson:_________________________________________ Phone:_______________________________ Fax:_____________________________ Product Information: Component Model Number(s) for LOWER UNIT (in order left to right, separated by commas):________________________________ _____________________________________________________________________________________________________________ Component Model Number(s) for UPPER UNIT, if applicable (in order left to right, separated by commas):_____________________ _____________________________________________________________________________________________________________ Drawing of Requested Configuration (please be specific): Finish:______________________________________ Hardware Selection:__________________________ Work Surface Shape: Straight Line Corner Unit (L‐shaped) Top Depth: 20” Deep 24” Deep Common Top? Yes (order lower units as “no top” – NT) No Top Depth/Length: 7668‐20‐105” 7668‐24‐105” 7668‐20‐70” 7668‐24‐70” 7668‐20‐35” 7668‐24‐35” CUSTOM‐20:_________________inches CUSTOM‐24:_________________inches Lower Components (indicate quantity for each) ___7655 ___7656 ___7657 ___7658 ___7659 ___7660 ___7667‐20 ___7667‐24 ___7669‐20 ___7669‐24 ___7670 ___7671 Custom office units cannot be canceled, exchanged, refunded, or altered once they have entered production. If this is a fully custom unit, a custom ___7672 ___7673 quote and drawing will be supplied to you before the order is built. Upper Components (indicate quantity for each) Date:_________________________________________________________ ___7661 ___7662 ___7665 Customer Signature: ___7666 ___7674‐35 ___7674‐70
Order Information:
______________________________________________________________
C
E
A
L
D
K
N
C C
B
C
K
A
E
A
F
E
C
K
C
D
F
C C
A
A
E
E
C
C
C F
K
C
K
K
D
D
C
C
F
K
L B
B
E
E
C
C
B
L
B
K
M
M
N
N
M
E
B
F
C
K
K
B
D
L E
C C
ML
E
B
B
C
N B
7761 7761
-12 56-12 -18 56-18
8 758
7755-12 7755-12
7757-12 7757-12 7757-18 7757-18
7762 7762
7759 7759
7756-12 7756-12
7755-12 7755-12
7756-12 7756-12
7650 A
7654 E
7664 F
7652 C
7658 K
D 7653
L B 7651
E 7654
7652 C
C 7652
7658 K
C 7652
B
Metropolitan Custom Office Program Sample Office Layout A
Upper Units Model
Description
7661 7662 7665 7666
70” Deck 35” Deck 35” Deck Upper Corner Unit
Lower Units Qty 1 1 2 1
Model
Description
7669-24L 7658 7655 7656 7670 7668-24-105 7668-24-70 7667-24
24” Outside End 2 Drawer Wide File 3 Drawer File 2 Drawer File Inside Top Support 24” Counter Top 24” Counter Top 24” Corner Top
Qty 1 1 1 1 1 1 1 1
Metropolitan Custom Office Program Sample Office Layout B
Upper Units Model
Description
7661 7662 7665 7666
70” Deck 35” Deck 35” Deck Upper Corner Unit
Lower Units Qty 1 1 2 1
Model
Description
7657 7658 7655 7656 7670 7673 7668-24-105 7668-24-70 7667-24
2 Door Cabinet 2 Drawer Wide File 3 Drawer File 2 Drawer File Inside Top Support End Filler 24” Counter Top 24” Counter Top 24” Corner Top
Qty 1 1 1 1 1 2 1 1 1
Metropolitan Custom Office Program Sample Office Layout C
Upper Units Model
Description
7661 7662 7665 7666
70” Deck 35” Deck 35” Deck Upper Corner Unit
Lower Units Qty 1 1 1 1
Model
Description
7657 7658 7655 7670 7668-20-70 7667-20
2 Door Cabinet 2 Drawer Wide File 3 Drawer File Inside Top Support 20” Counter Top 20” Corner Top
Qty 1 1 1 1 2 1
Metropolitan Custom Office Program Sample Office Layout D
Upper Units
Lower Units
Model
Description
Qty
7664-35 7664-70
35” Shelves 70” Shelves
1 1
Model
Description
7669-20L 7658 7670 7668-20-70 7668-20-35 7667-20
20” Outside End 2 Drawer Wide File Inside Top Support 20” Counter Top 20” Counter Top 20” Corner Top
Qty 1 1 1 2 1 1