Structall is a manufacturer and distributor of SIPs (Structural Insulated Panels) as well as a wide range of aluminum extrusion, windows, doors, and many other building supplies. Structall SIPs are used as floors, roofs, and structural walls - from patio covers and carports to screen rooms, room additions, residential home construction, and commercial building construction.
• Custom Order Entry Program
All documents laser-printed with full item descriptions. Easy to understand - no cryptic acronyms.
• Emailed order acknowledgements
Customers know what they are getting at what price.
• Contact call the day before delivery
Always a customer approval on backorders. No surprises when truck arrives.
No other distributor takes the time and expense to protect the product like Structall.
Foam bumpers on both the male and female sides of panels. Heavy cardboard endcaps installed for added protection against damage and ease of stacking. All extrusion and pan orders are stretch wrapped, which helps prevent damage on our truck and yours.
Each item is labeled by customer and job. You don’t have to sort through the material on multiple jobs.
Orders are delivered on OUR trucks by OUR drivers Loads are specially loaded and blocked at our facility and reblocked after every stop. This results in less damage and confusion with the paperwork.
• Extensive Marketing Support
Pre-Printed Brochures, Customized Flyers, Product Catalogs, Free Product Samples.
• The only supplier with six color options in panels, five colors in extrusion, and four colors for pans.
Once your order has been assigned with others in the region, it is added to a shipping manifest. The manifests are taken to the loading dock personnel who will begin the loading process.
The manifest is then scanned into the Dock Workstation where the contents of your order are broken down into individual units. Each unit is assigned a unique serial number and each order is assigned a color code.
Three piece colored tags that correspond to your order are printed with the individualized serial numbers, as well as extrusion and package numbers, then applied to the appropriate units.
As each unit is scanned, the Dock Workstation changes scanned units from “Unloaded” to “Loaded” status as they are loaded onto the truck.
After loading is completed, a Shipping Superviser will compare the shipping manifest to the Dock Workstation before the truck is allowed to leave.
Corporate Headquarters
350 Burbank Road
Oldsmar, FL 34677
Sales Desk: 877.314.2509
Information: 800.969.3706
Local: 813.855.2627
Fax: 813.814.0018
info@structall.com
Lakeland Service Center
5120 Great Oak Drive
Lakeland, FL 33815
Toll-Free: 855.431.2642
Local: 863.577.0600
Fax: 863.577.0659
San Antonio Service Center
3802 Binz Engleman, Ste. A105 San Antonio, TX 78219
Toll-Free: 800.880.4198
Local: 210.225.7997
Fax: 210.225.7197 sanantonio@structall.com
Gulf Coast Service Center
5045 Iberville Street, Unit B St. Gabriel, LA 70776
Toll-Free: 800.310.1405
Local: 225.673.8776
Fax: 225.677.8133 sbsla@structall.com Newland Service Center Coming Soon Lenoir Service Center Coming Soon
Corporate Headquarters
350 Burbank Road, Oldsmar, FL 34677
Sales Desk: 877.314.2509 | Information: 800.969.3706 | Local: 813.855.2627 | Fax: 813.814.0018
info@structall.com
Hours of Operation: Monday - Friday, 7:30 AM - 5:00 PM Eastern
Head north on U.S. Highway 19 to SR-580 or SR-584. Then east to the county line (Race Track Road). Turn left (north) on Race Track Road and go approximately 7/10ths of a mile to Douglas. Turn left (west) on Douglas, go approximately 2 blocks to Burbank. Turn right (north) on Burbank, go about 1/2 block. The factory is located on the right hand side at 350 Burbank Road.
Take I-75 to I-275 south and exit at the Tampa International Airport exit. Travel north on Memorial Highway, continuing north on Eisenhower Boulevard until it dead ends at Hillsborough Avenue or SR580. Travel west on Hillsborough Avenue approximately 14 miles to the county line (Race Track Road). Turn right (north) on Race Track Road and go approximately 7/10ths of a mile to Douglas, turn left (west) on Douglas, go approximately 2 blocks to Burbank Road. Turn right (north) on Burbank, go about 1/2 block. The factory is located on the right hand side at 350 Burbank Road.
Lakeland Service Center
5120 Great Oak Drive, Lakeland, FL 33815
Toll-Free: 855.431.2642 | Local: 863.577.0600 | Fax: 863.577.0659
info@structall.com
Hours of Operation: Monday - Friday, 7:30 AM - 5:00 PM Eastern
Head East on SR-580 (Hillsborough Ave./Tampa Rd.). Turn right (SE) on Memorial Hwy. (CR 576). Keep to your right onto Independence Pkwy. Bear right onto the ramp merging onto SR589 (Veterans Expy.). Exit right on ramp to North I-275. Exit I-4 and travel about 25 miles. Exit 25 South (County Line Road) and
go about 2 blocks. Turn East (left) on Great Oak Drive. After crossing railroad tracks, Structall is on right.
Follow I-4 East about 25 miles. Take exit 25 South (County Line Road) and travel about 2 blocks. Turn East (left) on Great Oak Drive. After crossing railroad tracks, Structall is on right.
Follow I-4 West to exit 25. At top of ramp, go South (right) on County Line Road about 2 blocks. Turn East (left) on Great Oak Drive and go 2 blocks crossing railroad tracks. Structall is on the right.
San Antonio Service Center
3802 Binz Engleman, Ste. A105, San Antonio, TX 78219
Toll-Free: 800.880.4198 | Local: 210.225.7997 | Fax: 210.225.7197
sanantonio@structall.com
Hours of Operation: Monday - Friday, 7:30 AM - 4:30 PM Central
Head south on I-35 and take the BinzEngleman exit (#162) turning right. Structall Building Systems will be on your left across from the Brooke Army Medical Center, before the first traffic light at George Beach.
Take I-10 and exit at I-410. Head north on I-410 till you get to the Binz-Engleman exit (#161). Turn left and follow the road under I-35. Structall will be on your left across from the Brooke Army Medical Center, before the first traffic light at George Beach.
Go north on I-35 and take the Binz-Engleman exit (#161). Turn left and follow under I-35. Structall will be on your left across from the Brooke Army Medical Center, before the first traffic light at George Beach.
Gulf
sbsla@structall.com
Hours
• Internal Snap-Lock fastening feature.
• Snaps together in header.
• No rocking of panels required.
• Metal is chemically bonded to foam.
• Continuous Insulation.
• Quick and easy to install.
• Foam thicknesses from 2” to 8”.
• Panels come in 48” or 23-1/8” widths.
• Eliminates condensation problems.
• Skylights and fans installed with ease.
Stucco Embossed Aluminum
Stucco Embossed
ga Stucco Embossed G90 Galvanized Steel
ga Smooth G90 Galvanized Steel
Foam Interface
• Florida Product Approved (HVHZ)
Approval #: FL-15491-R6
Approval #: FL-21443-R5
Approval #: FL-19974-R3
• California Building Code Approved
• Texas Department of Insurance Approved
Approval #: RC-247
• International Code Council - ICC
The Snap-N-Lock™ Panel is recognized by ICC-ES ESR-2488 and ESR-3152
• ENERGY STAR® Certified .024 & .030 Aluminum Snap-N-Lock™ Composite Roof Panels with White Tuff-Kote Dual Layer Paint Finish meet or exceed the requirements set forth by ENERGY STAR®.
Fan Beam
• Cont. 1.5” x 3” x .050” Alum. Fan Beam Extrusion.
• Fasten fan or light using self-tapping screws.
• Surrounded on all sides by foam for better lamination as well as to reduce telegraphing and condensation within fan beam
Cedar Embossed with
• Ribbing is 8” OC.
• Internal Snap-Lock fastening feature.
• Snaps together in header.
• No rocking of panels required.
• Metal is chemically bonded to foam.
• Continuous Insulation.
• Quick and easy to install.
• Foam thicknesses from 2” to 8”.
• Panels come in 48” or 23-1/8” widths.
• Eliminates condensation problems.
• Skylights and fans installed with ease.
• Florida Product Approved (HVHZ)
Approval #: FL-15491-R6
Approval #: FL-21443-R5
Approval #: FL-19974-R3
• California Building Code Approved
• Texas Department of Insurance Approved Approval #: RC-247
• International Code Council - ICC
The Snap-N-Lock™ Panel is recognized by ICC-ES ESR-2488 and ESR-3152
• ENERGY STAR® Certified .024 & .030 Aluminum Snap-N-Lock™ Composite Roof Panels with White Tuff-Kote Dual Layer Paint Finish meet or exceed the requirements set forth by ENERGY STAR®
• Cont. 1.5” x 3” x .050” Alum. Fan Beam Extrusion.
• Fasten fan or light using self-tapping screws.
• Surrounded on all sides by foam for better lamination as well as to reduce telegraphing and condensation within fan beam
White
Smooth
26ga G90 Galvanized Steel
Ceram-A-Star 1050 Coating
White Stucco Embossed
26ga G90 Galvanized Steel
Ceram-A-Star 1050 Coating
White
Stucco Embossed .024 & .030 Aluminum
TUFF-KOTE TUFF-KOTE
White Cedar Embossed .024 Aluminum
Stucco Embossed .024 Aluminum
Tuff- Kote is a dual-layer paint finish with a base color layer, and a clear protective top layer. The top coat is fused to the base coat during the baking cycle. The result is a paint finish that is more resistant to damage than standard paint finishes.
• Durable satin matte finish.
• More resistant to weather and alkalines.
• Requires less maintenance than other finishes.
• Resists scratching, marring, corrosion and fading.
• Protects against surface damage during installation process.
TUFF-KOTE TUFF-KOTE
Embossed .024 Aluminum Desert Sand Cedar Embossed .024 Aluminum
Sandstone Stucco Embossed .024 Aluminum
TUFF-KOTE
Sandstone Cedar Embossed .024 Aluminum
TUFF-KOTE TUFF-KOTE
Stucco Embossed .024 Aluminum
TUFF-KOTE TUFF-KOTE
Stucco Embossed .024 Aluminum
Thermal resistance is an index of material’s resistance to the flow of heat. It is the reciprocal of the K or C-value.
The higher the R-value, the better the resistance to the flow of heat (BTUs) and the better the insulation. R-values are usually reported for a stated thickness. R-values for different materials, or different thicknesses of the same material, may be added together to reach a total R-value for a system. R = or T K 1 C
The thermal resistance, or R-value (in ft2 - hr - °F / BTU), of OSB panels is listed below. Thicker panels have more insulating value; therefore R-values increase with increasing panel thickness. These values are listed in Table 2 of the Structural Board Association’s “OSB in Wood Frame Construction,” (U.S. Edition 1996/97).
The thermal resistance, or R-value (in ft2 - hr - °F / BTU), of plywood panels is listed below. Thicker panels have more insulating value; therefore R-values increase with increasing panel thickness. These values are listed in Chapter 25, Table 4 of the 2001 ASHRAE Handbook published by the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE).
U-Value Factor
Overall coefficient of heat transmission, or the quantity which will flow through a specific building section composed of a number of materials one square foot in area during one hour when there is hot or cold side temperature difference 1° F.
Abstract: Analysis of three roofs for Solar Reflectance per ASMT C1549 and Emittance per ASTM C1371 for ENERGY STAR® approval.
Samples: Initial Snap-N-Lock™ Insulated Panel w/ White Tuff-Kote Gold Dual Layer Paint Finish 3 Roofs - Site 1, Site 2, Site 3
3” Thick - 1lb EPS Foam
Stucco-embossed: White/White
• W hen ordering Snap-N-Lock™ stock panels, specify quantity, length and width of panels.
• Next day delivery available on established truck routes for established customers, depending upon stock availability.
• Cut-off time is 12:00 Noon for next day delivery. We prefer you fax your order to ensure accuracy.
• Phone orders will always be read back to you for your verification, but we do not accept responsibility for authenticity of order.
2’ Wide, Stock Snap-N-Lock panels are Net 23-1/8” in width.
P-SL3024TW2TW2---096
P-SL3024TW2TW2---108
P-SL3024TW2TW2---120
P-SL3024TW2TW2---132
P-SL3024TW2TW2---144
P-SL3024TW2TW2---156
P-SL3024TW2TW2---168
P-SL3024TW2TW2---180
P-SL3024TW2TW2---192
P-SL3024TW2TW2---216
P-SL3024TW2TW2---240
P-SL3024TW2TW2---264
P-SL3024TW2TW2---288
4’
P-SL3048TW2TW2---096
P-SL3048TW2TW2---108
P-SL3048TW2TW2---120
P-SL3048TW2TW2---132
P-SL3048TW2TW2---144
P-SL3048TW2TW2---156 13’ 11.18
P-SL3048TW2TW2---168
P-SL3048TW2TW2---180 15’
P-SL3048TW2TW2---192 16’ 11.18 715.52
P-SL3048TW2TW2---216 18’ 11.18 804.96
P-SL3048TW2TW2---240 20’ 11.18 894.40
P-SL3048TW2TW2---264
P-SL3048TW2TW2---288
Extruded Beam Laminated Inside Panel (available in Stock Panels 4’ Wide)
Install with narrow section of foam UP Beam is surrounded on all sides by foam for better lamination and to reduce telegraphing.
• In Custom ordered panels, Extruded Beam can be placed anywhere in the panel (6” from either edge).
• Beam is centered in all Stock Panel Sizes.
.024 Aluminum Tuff-Kote Paint Finish
Custom-Sized Snap-N-Lock™ Panels
Stucco-embossed: White, Ivory, Bronze, Sandstone, Adobe Cedar-embossed: White, Ivory, Desert Sand, Sandstone
Prices Subject to Change Without Notice
Color Combinations Available**
White / White Ivory / Ivory Desert Sand / Desert Sand
DO NOT STORE or INSTALL BRONZE and ADOBE SKIN FACES IN DIRECT SUNLIGHT.
Heat will expand the metal, causing the panel to bow and make it difficult to snap the panels together.
Thermal bowing does not represent a manufacturing defect.
Stucco-embossed: White Not Available in Cedar-embossed
Extruded Beam Laminated Inside Panel (available in Stock Panels 4’ Wide)
Any damage incurred through incorrect storage or installation will void the warranty.
• Panels are custom made and charged in 6” increments.
• Available up to 32’ in length.
• Lengths over 24’ will have a surcharge of 10% per sq. foot added to list price.
*Specify Level or Grooved (8” center to center) N/C. Available in 3” Panel only. ** See Note on Colors next page.
SPECIAL SIZES & LAMINATIONS AVAILABLE
WRAPPING
Standard Wrap - Cardboard Ends & Center / Sq.Ft. N/C
Common Carrier - Full Cardboard, Two Panels Per Box / Sq.Ft.
Fan Beams Not Available on Square Cut Panels.
Install with narrow section of foam UP Beam is surrounded on all sides by foam for better lamination and to reduce telegraphing.
• In Custom ordered panels, Extruded Beam can be placed anywhere in the panel (6” from either edge).
• Beam is centered in all Stock Panel Sizes.
.024 Aluminum Tuff-Kote Paint Finish 2-Color, Custom-Sized Snap-N-Lock™ Panels
Stucco-embossed: White, Ivory, Bronze, Sandstone, Adobe Cedar-embossed: White, Ivory, Desert Sand, Sandstone
Prices Subject to Change Without Notice
Color Combinations Available**
White / White Ivory / Ivory
White / Ivory Ivory / Sandstone
White / Sandstone Ivory / Adobe
White / Adobe Ivory / Bronze
White / Bronze Ivory / Desert Sand
White / Desert Sand Desert Sand / Sandstone
Desert Sand / Bronze Desert Sand / Adobe Desert Sand / Desert Sand
DO NOT STORE or INSTALL BRONZE and ADOBE SKIN FACES IN DIRECT SUNLIGHT.
Heat will expand the metal, causing the panel to bow and make it difficult to snap the panels together.
Thermal bowing does not represent a manufacturing defect.
.030 Aluminum Tuff-Kote Paint Finish
2-Color, Custom-Sized Snap-N-Lock™ Panels
Stucco-embossed: White
Not Available in Cedar-embossed
8”
Extruded Beam Laminated Inside Panel (available in Stock Panels 4’ Wide)
Any damage incurred through incorrect storage or installation will void the warranty.
• Panels are custom made and charged in 6” increments.
• Available up to 32’ in length.
• Lengths over 24’ will have a surcharge of 10% per sq. foot added to list price.
*Specify Level or Grooved (8” center to center) N/C.
Available in 3” Panel only.
** See Note on Colors next page.
SPECIAL SIZES & LAMINATIONS AVAILABLE WRAPPING
Standard Wrap - Cardboard Ends & Center / Sq.Ft. N/C
Common Carrier - Full Cardboard, Two Panels Per Box / Sq.Ft. 1.00
Fan Beams Not Available on Square Cut Panels.
Install with narrow section of foam UP Beam is surrounded on all sides by foam for better lamination and to reduce telegraphing.
• In Custom ordered panels, Extruded Beam can be placed anywhere in the panel (6” from either edge).
• Beam is centered in all Stock Panel Sizes.
• 26 ga G90 Galvanized USDA Steel Skins
• Ceram-A-Star Sil-Polyester Coating
• Expanded Polystyrene (EPS) Core
• Built-in Air and Water Barrier
• True Structural Insulated Panel
• Lab Tested Load-Bearing Walls and Roofs
• Internal Snap-Lock fastening feature
• Continuous Foam Insulation for Max U-Value
• Greatly Decrease Dry-In and Overall Build Time
• Use Smaller Crews and No Heavy Equipment
26 ga Steel Stucco Embossed
26 ga Steel Smooth G90 Hot-Dipped Galvanized 40 Year Polyester Paint
Insulated Foam Interface
• Roof Panel & Wall Cladding
Florida Product Approved
HVHZ Approved
Approval #: FL-15491-R6
• Structural Wall Panel
Florida Product Approved
HVHZ Approved
Approval #: FL-19974-R3
• International Code Council - ICC
Polystyrene Core (EPS) Insect Resistant - Available
Recognized by ICC-ES # ESR-3152
• California Building Code Approved
Structall Energy-Wise homes are capable of exceeding Energy Star and Builders Challenge efficiency requirements and can nearly achieve Net Zero Home status.
When ordering Snap-N-Lock panels specify quantity, length and width of panels, smooth or stucco embossed skin, thickness of foam, and type of foam.
When ordering Snap-N-Lock panels specify quantity, length and width of panels, smooth or stucco embossed skin, thickness of foam, and type of foam.
• Panels are custom made and charged in 6” increments.
• Available up to 32’ in length.
*Specify Level or Grooved (8” center to center) N/C. Available in 3” Panel only.
** See Note on Colors next page. SPECIAL SIZES & LAMINATIONS AVAILABLE
26 Gauge USDA Steel Snap-N-Lock™ Panels - INSECT RESISTANT Smooth or Stucco-embossed: White Only Not Available
Prices Subject to Change Without Notice
Thermoplastic has been used in products like auto grills and mirrors, garden furniture and outdoor signs because of its weatherability, durability, thermal stability, and scratch & impact resistance. Thermoplastic won’t crack, dent or tear like some products on the market. It’s both tough and rigid. It also has an excellent resistance to outdoor exposure, aging, stains, chemicals, and yellowing. It won’t sag or bow, even when exposed to high heat. In addition, the color runs completely through the sheet, reducing the appearance of abrasions.
Always use the cleaner according to the manufacturer’s directions. Use a soft, clean cloth to apply the cleaner. Apply the cleaner to the cloth. Clean only a small portion of the surface at one time. After cleaning, rinse off the surface as completely as possible.
For general cleaning the following can be used:
Ivory (soap and water solution)
Formula 409
Windex
Spic and Span
Scrubbing Bubble
Fantastik
Simple Green
Pine Sol.
For heavy cleaning, use the following, but remove immediately after use:
Soft Scrub (may slightly abrade surface)
Bug & Tar Remover
OOPS
DO NOT USE:
Acetone
Goof Off
Cleaners that contain esters, ethers, ketones, aromatic and chlorinated hydrocarbons, or Isopropanol (concentrations greater than 25%).
WEATHERABILITY - Excellent resistance to outdoor exposure, aging and yellowing. Same material used in auto grills and mirrors, garden furniture, and outdoor signs.
DURABILITY - Great toughness and rigidity. Will not crack like FRP.
THERMALLY STABLE - Reduced sagging and bowing in high heat conditions.
SCRATCH RESISTANT - Color fast through the sheet. Will not show abrasion like aluminum.
IMPACT RESISTANT - Will not dent or tear like aluminum.
Thermoplastic Panels are perfect as an insulated, impact resistant kickplate in screen and modular rooms. Use Thermoplastic panels when damage from pets and children are a concern. Couple with Vinyl windows for Modular Rooms and Pet Resistant Screen for Screen Rooms.
Sandcastle Embossed - .028
Stucco Embossed - .028
Stucco Embossed - .040
If ordering Rigiwall on one side only, Structall recommends that it be used as the exterior finish to take advantage of the product’s unique benefits. Special sizes and laminations will not be available for this particular product.
.028 Rigiwall both sides
“Sandcastle” texture available in the following colors: White, Ivory, Adobe, Sandstone
“Stucco” texture available in the following colors: White, Sandstone
Sizes
.028 Rigiwall one side/
.024 Aluminum Tuff-Kote Gold one side
“Sandcastle” texture available in the following colors: White, Ivory, Adobe, Sandstone
“Stucco” texture available in the following colors: White, Sandstone
Aluminum Choices:
Stucco Embossed: White, Ivory, Bronze, Sandstone, Adobe Cedar Embossed: White, Ivory, Sandstone
Sizes available: 4’ x 8’ , 4’ x 10’ , 4’ x 12’
“Sandcastle” texture available in the following colors: Bronze
“Stucco” texture available in the following colors: White, Sandstone, Adobe
Sizes available: 4’ x 8’ , 4’ x 10’
.040 Rigiwall one side/
.024 Aluminum Tuff-Kote Gold one side
.040 “Stucco” texture available in the following colors: White, Sandstone, Adobe
Aluminum Choices:
Stucco Embossed: White, Ivory, Bronze, Sandstone, Adobe Cedar Embossed: White, Ivory, Sandstone
Sizes available: 4’ x 8’ , 4’ x 10’
.024 Aluminum - both sides
Stucco-embossed: White, Ivory, Bronze Cedar-embossed: White, Ivory
.024 Aluminum Sandstone & Adobe Stucco Stucco-embossed: Sandstone, Adobe
.060 Fiberglass Reinforced Plastic (FRP) - both sides
UV Rated
Stucco
.060 FRP - one side / Aluminum - one side
FRP Stucco Finish: White, Ivory
Aluminum Stucco-embossed: White, Ivory, Bronze
Aluminum Cedar-embossed: White, Ivory
Special
1/4” Panel - 3 Ply - clad both sides
1/4” BL Exterior Plywood with Tuff-Kote Aluminum on both sides Available
1” Panel - 5 Ply - clad both sides
1lb
2” Panel - 5 Ply - clad both sides
1lb density EPS foam core
1/4” BL Exterior Plywood with Tuff-Kote Aluminum on both sides
Spandrel panels not included on this sheet will be by quote.
WRAPPING CHARGES:
Standard Wrap - Cardboard Ends & Center / Sq.Ft. N/C
Common Carrier - Full Cardboard, Two Panels Per Box / Sq.Ft. 1.00
CA3016IVYIVYCE-LF
CA3016IVYIVYSE-LF
CA3016IVYIVYSM-LF
CA3016BRZBRZCE-LF CA3016BRZBRZE-LF
CA3016BRZBRZSM-LF
Sample Case w/ Embroidered Logos (18.5” W x 16.5”
Black 600 denier bag with black handle and shoulder straps. Reinforced compartments protect samples from damage. (SKU# FLPATSAMPLECASE)
• Panel Metal Color Fandeck
• 3” Snap-N-Lock Panel Sample with Fan Beam
• 3” Snap-N-Lock Panel Sample with Fan Beam, Gutter, and Valance
• 3” Snap-N-Lock Panel Sample with Fan Beam and Drip Edge
• 4” Snap-N-Lock Panel Sample with Fan Beam
• 4” Low-Profile Extruded Gutter
• 4” Drip Edge
• 2” x 7” Edge Beam
• 2” x 5” Edge Beam
• 3” x 3” Square Post
• 4” x 4” Square Post
• 2” x 4” x .050” Side Post Flat Spline
• Perimeter Snap w/ 1” x 2” Open Back Smooth Flat Spline
813-855-2627 Fax: 813-814-0018
3” Low Profile Receiving Gutter
6”
Order modular rooms pre-cut and pre-assembled in wall units for extremely fast installation. Rooms can go up in as little as one day! Structall offers five colors in panel skins, extrusions, doors & windows, and accessories to help create rooms that are truly unique. Insulated roof, wall, and floor systems all work together for easy installation!
• 2 " or 3" systems available.
• Internal screw bosses leave fewer screws exposed.
• Custom Designed to your Specifications.
• 5 colors available - Including Adobe & Sandstone.
Choose between: Open, Screen, Vinyl or Glass Modular Wall Units.
Prices Subject to Change Without Notice
Wall Description
2” Modular Open Wall System (non-thermo)
2” Modular Open Wall System (non-thermo)
3” Modular Open Wall System (non-thermo)
3” Modular Open Wall System (non-thermo)
3” Modular Open Wall System (non-thermo)
3” Modular Open Wall System (thermo-break)
3” Modular Open Wall System (thermo-break)
3” Modular Open Wall System (thermo-break)
* Solid Filler Panel (2” or 3” Wall System)
* .028 Rigiwall Vinyl Wall (One Side Only)
* .028 Rigiwall Vinyl Wall (Both Sides)
* .040 Rigiwall Vinyl Wall (One Side Only)
* .040 Rigiwall Vinyl Wall (Both Sides)
* Electrical Chase Holes (3” Wall Only)
* 18 / 14 Screen - Charcoal
* 20 / 20 Screen - Charcoal
Window Options
Glass - Horizontal Slider (H/S) or Single-Hung (S.H.) - Up to 60” High
* Single Glaze + Clear
* Single Glaze + Tint (Bronze, Gray, Green, Obscure)
* Single Glaze + Tint (Bronze Reflective, Graylite 31)
* Single: Tempered
* Insulated Glass + Clear
* Insulated Glass + Tint (Bronze, Gray, Green, Obscure)
* Insulated Glass + Tint (Bronze Reflective, Graylite 31, FL Low-E)
* Insulated Glass + Low-E Clear
* Insulated Glass: Tempered
Glass - H/S or S.H. - Over 60” to 72” High
* Use Total Window Cost Above, Plus
Glass - Kickplates & Transoms (Note: Guideline Only, Not Firm Price)
* Single Glaze Clear
* Single Glaze Clear - Tempered
* Insulated Glass Clear
* Insulated Glass Clear - Tempered
Glass - Trapezoids
Vinyl Film - Vertical Vinyl 4-Track (V4T)
* Spring or Pin - Up to 66” High (Clear, Smoke Gray, Bronze, Purple)
* Spring or Pin - Over 66” - 72” High (Clear, Smoke Gray, Bronze, Purple)
* Spring or Pin - Over 72” - 84” High (Clear, Smoke Gray, Bronze, Purple)
Vinyl Film - Horizontal Sliders (H/S)
* Spring or Pin - Up to 72” High (Clear, Smoke Gray, Bronze, Purple)
* Spring or Pin - Over 72” - 84” High (Clear, Smoke Gray, Bronze, Purple)
Vinyl Film - Lip Frames / Deadlites
Acrylic - Horizontal Sliders / Deadlites / Trapezoids
and Under
plus, max 10’
plus, max 12’
2” Prime Entry Doors
Prices Subject to Change Without Notice
3’-0” x 6’x8” Full Single Hung - Single Glaze - Clear
3’-0” x 6’x8” Full Single Hung - Insulated - Clear
3’-0” x 6’x8” Half Single Hung - Single Glaze - Clear
3’-0” x 6’x8” Half Single Hung - Insulated - Clear
3’-0” x 6’x8” Full View - Single Glaze - Clear
3’-0” x 6’x8” Full View - Insulated - Clear
3’-0” x 6’x8” Vertical Vinyl 4-Track
* Hardware Package: Lockset + Deadbolt + Threshold (Bumper or Saddle)
* Adjustable Bug Sweep (for inswing door and/or saddle threshold)
* Astragal for Dual Doors
SNAP-N-LOCK Insulated Panel (Complete Roof System)
3” .024 Aluminum - 1lb Virgin Foam
3” .024 Aluminum - 2lb Virgin Foam
3” .030 Aluminum - 1lb Virgin Foam
3” .030 Aluminum - 2lb Virgin Foam
4” .024 Aluminum - 1lb Virgin Foam
4” .024 Aluminum - 2lb Virgin Foam
4” .030 Aluminum - 1lb Virgin Foam
4” .030 Aluminum - 2lb Virgin Foam
6” .024 Aluminum - 1lb Virgin Foam
6” .024 Aluminum - 2lb Virgin Foam
6” .030 Aluminum - 1lb Virgin Foam
6” .030 Aluminum - 2lb Virgin Foam
* Additional Cost: Fan Beam Laminated in Panel
HALF-SNAP Insulated Panel (Complete Roof System)
4” .024 Aluminum One Side / OSB One Side - 1lb Virgin Foam
4” .030 Aluminum One Side / OSB One Side - 1lb Virgin Foam
6” .024 Aluminum One Side / OSB One Side - 1lb Virgin Foam
6” .030 Aluminum One Side / OSB One Side - 1lb Virgin Foam
DOUBLE OSB Insulated Panels (Floor or Wall)
4-1/2” Double OSB - Type A - Standard Foam Recess - Standard Sizes
6-1/2” Double OSB - Type A - Standard Foam Recess - Standard Sizes
8-1/2” Double OSB - Type A - Standard Foam Recess - Standard Sizes
* Additional Cost: .024 Aluminum Metal Vapor Barrier on One Side
** Ask your Sales Rep about current window and door prices.
Rigiwall Stucco .028 Rigiwall Sandcastle .040 Rigiwall Stucco
Indicate Interior (INT), Exterior (EXT), or BOTH in the appropriate row and column above. FRP is not available for EXT finish. Cedar finish must be 48” or under, to maintain vertical lines.
Diagrams to the right for measurement letters.
Please check one:
Please check one:
To House Attachment (see diagram to right)
To Soffit Attachment (see diagram to right)
Screen Color: Charcoal Specs
18/14 (standard)
20/20 (upcharge)
Pet Resistant (upcharge)
Please indicate module sizes and location, room dimensions, door location and swing. Header panel will vary depending on unit height. Must be a minimum of 4”.
Components
Prices Subject to Change Without Notice
Thermo Mullions are recommended for insulated glass rooms.
Use Non-Thermo Mullions (A1 & B1) for screen rooms and glass rooms that are not insulated.
2” x 3” Thermo Female Mullion
EXT33102
Use as one part of two part upright and to frame top and bottom of window openings.
2” x 3” Thermo Male Mullion EXT33101
Snaps into female mullion, eliminating the need for fasteners. Use as one part of two part upright and to fit corner post and receiving channel.
Prices Subject to Change Without Notice
2” x 3” Female Mullion
EXT33002
2” x 3” Snap Male Mullion EXT33011
Snaps into female mullion, eliminating the need for fasteners. Use as one part of two part upright and to fit corner post and receiving channel.
3” Thermo Top Cap
EXT33106
Use to frame top of side wall modules when using 3” Thermo Modular Room Adjustable Top Cap & Lower Assembly.
Use as one part of two part upright and to frame top and bottom of window openings. G
3” Thermo Corner Post EXT13101
3” Adjustable Thermo Top Cap Assembly
EXT33104 & EXT33105
Adjusts to roof pitch. No more gap between roof panels and front wall.
3” Adjustable Top Cap must be used with 3” Thermo Adjustable Top Cap Lower Assembly.
3” Thermo Base Channel
EXT13106
Use to receive panels on slab and to frame bottom of wall modules.
H
3” 1/2 Keyed Receiver EXT33013
Receives kick panel and attaches to female and male mullions.
Receives wall modules at all corners of structure.
3” Front Window Stop
EXT33004
Support base for anchoring window.
3” 90° Back Window Stop EXT33013
2” Female Mullion EXT12112
Use as one part of two part upright and to frame top and bottom of window openings.
2” Top Cap Receiving Channel EXT12110
Use to frame top of side and front wall modules. Also used on the front wall modules in place of components C & D.
Prices Subject to Change Without Notice
2” Male Mullion EXT12113
Use as one part of two part upright and to frame top and bottom of window openings.
H
2” Keyed Receiver EXT12111
Receives kick panel and attaches to female and male mullions.
E G
Receives wall modules at all corners of structure. D C
2” Mullion EXT12108
Receives two square cut panels. Width is consistent with finished mullion attachment.
F
2” Base Channel EXT12106
Use to receive panels on slab and to frame bottom of wall modules.
2” Snap Corner Post EXT12114
Note: Components not pictured include: Downspouts, Elbows, Drop Outs, Straps, Fasteners, and Caulking.
3” Thermo Wall Header EXT13103
Fasten to existing structure to receive roof panels.
3” Drip Edge Fascia Trim EXT13009
Use to trim front and sides of roof panels. Traditional gutters can be attached to match existing structure.
3” Wall Header EXT13003
Fasten to existing structure to receive roof panels.
3” Receiving Valance EXT13002 & EXT13002LP
Attach to side of roof panels when used with Receiving Gutter.
3” Receiving Gutter EXT13001 & EXT13001LP
Attach to face of roof panel.
Snap-N-Lock Roof Panel
• Internal Snap-Lock fastening feature.
• Snaps together in header.
• No rocking of panels required.
• Continuous Insulation.
• Quick and easy to install.
• Foam thicknesses from 2”, 3”, 4”, 6”, 8”.
• Panels come in 48” or 23-1/8” widths.
• Eliminates condensation problems.
• Skylights and fans installed with ease.
The Adjustable Top Cap Assembly provides a flexible method of attaching roof panels to modular room walls. Adjustable from 3/12 to 5/12 pitch, the assembly works well for both gabled and shed style roof systems. The adjustability eliminates the need to miter panels at the joint. Thermally broken, the extrusion assembly prevents the transmission of heat/ cold from the outside to the inside of the room.
Sample Case w/ Embroidered Logos (18.5” W x 16.5” D x 13.0” H)
Black 600 denier bag with black handle and shoulder straps. Reinforced compartments protect samples from damage. (SKU# FLPATSAMPLECASE)
• Panel Metal Color Fandeck
• 3” Snap-N-Lock Panel Sample with Fan Beam
• 3” Snap-N-Lock Panel Sample with Fan Beam, Gutter, and Valance
• 3” Snap-N-Lock Panel Sample with Fan Beam and Drip Edge
• 4” Snap-N-Lock Panel Sample with Fan Beam
• 4” Low-Profile Extruded Gutter
• 4” Drip Edge
• 2” x 7” Edge Beam
• 2” x 5” Edge Beam
• 3” x 3” Square Post
• 4” x 4” Square Post
• 2” x 4” x .050” Side Post Flat Spline
• Perimeter Snap w/ 1” x 2” Open Back Smooth Flat Spline
813-855-2627 Fax: 813-814-0018
1
EXT20320312
EXT20320313
EXT20320315
EXT20320318
EXT20320324
EXT20320330
2 x 2 x .093 Equal Angle
1 x 2 x .063 Unequal Angle
2 x 3 x .125 Unequal Angle
4 x .1875 (3/16) Flat Bar
3 x 3 x .125 Square Post
These 2-piece extrusions are priced by the pair - ordered and sold by each piece.
These 2-piece extrusions are priced by the pair - ordered and sold by each piece.
Prices Subject to Change Without Notice
*Also Available
2x5 Edge Beam Splice
2x7 Edge Beam Splice
2x5 Edge Beam Cap
2x7 Edge Beam Cap
2x5 Wall Bracket
2x7 Wall Bracket
Greater spans than SMBs of the same size. Look at the span tables!
2 x 7 Edge Beam
Exclusive Smooth Beveled End Caps to Complement 2x5 and 2x7 Edge Beams.
• Durable ABS Plastic
• Color Matched to Beam Paint
• Snug and Flush Fit
• Attractive, Upscale Look
2 x 10 Edge Beam Splice
• Underside view is flat with ribs approximately every 2” and is preferred over corrugated systems. Looks very much like tongue and groove planks.
• Attaches easily to any structure.
• Gutter braces provided standard with each order to support both the extruded and roll-form gutters.
• Structall’s mounted gutter systems have less area to clog and are more accessible for cleaning than w-pan gutter. For added strength and durability, choose extruded gutter and valance.
Prices Subject to Change Without Notice
Helps prevent water from entering wall header.
• Pans are boxed on one end to help prevent wind blown water from entering wall header.
• Patio cover can be enclosed and insulation can be retrofitted to unit at the time of construction or later. Adding insulation to other patio systems reduces head room under the cover, produces inconsistent temperatures, and requires bug plugs which constantly pop out of place.
• This aluminum roof system is very low maintenance, only requiring an occasional light-pressure wash to rinse off dirt and debris.
.024 - 3” Riser Flat Pan Max Length - 4’-10”- 40 ft. .030 - 3” Riser Flat Pan Max Length - 4’-10”- 45 ft.
Stock sizes available
There is a 5% upcharge on lengths above 30 ft.
Note on Colors: Structall recommends using the metal color options of Sandstone, Bronze, Adobe, and Ivory for use on the bottom of the 3” Riser Flat Pan only. White is the best color to reflect the rays of the sun, reducing heat buildup and related expansion problems inherent with all aluminum products.
Secure valance bracket to pan every 4 ft. Brackets can extend as much as 4” from edge of pan. The front valance is then attached to the brackets. Secure the side valance directly to the pan.
Prices Subject to Change Without Notice
• All splices are concealed - fitting within the product so the appearance is smooth.
• Jobs are completed faster, easier, and result in a professional looking installation your customers will appreciate.
• We supply splices for many of our building products.
.063 Brake Metal
Pan Gutter Splice (for Extruded Pan Gutter)
Splice (for 3” & 4” Panels)
Roll Form Pan Gutter Splice
#10 x 3/4” SMS w/ 1/2” Neo Washer FLASHING
prenotched to accept tilt beam. 3" x 3" x .125 or 3" x 3" x .093 Square Post can also be used.
2" x 4" TILT BEAM
3" PAN WITH 3" EXTRUDED PAN VALANCE
3" PAN WITH ROLL FORM VALANCE
HEX HEAD MACHINE BOLT
#10 x 3/4” SMS w/ 1/2” Neo Washer
HEX HEAD MACHINE BOLT
GUTTER BRACE
1/4” x 2-1/4” Concrette Screw #10 x 3/4” SMS w/ 1/2” Neo Washer
3" EXTRUDED PAN GUTTER
3" x 3" FLUTED SQUARE POST or Self Mating Beam with hex nut attatch post and tilt beam with hex nut attatch post and base plate or Roll Form Gutter (as pictured in circle) or without
3" BASE PLATE WITH EARS
GUTTER BRACE
Convert from:
• Screen Rooms to Glass Rooms
• Single Skin to Insulated Roof
Insulates:
• Reduces Heat in the Summer
• Keeps Cold out in the Winter
• Reduces Condensation
• Dampens Noise and Quiets Existing Covers
• Install Now...or Retrofit Later!
Prices Subject to Change Without Notice
The Insulator End Cap is 1” x 2” x .063 aluminum which completes the Insulator Pan by protecting the foam. Use #8 x 1/2” Hex Washer Head Sheet Metal Screws to convert to the Insulator Pan - use caulk to seal each fastener.
Custom Lengths now available! Insulator Top Cap can be run to length to your specifications.
The Insulator Top Cap is fastened to the 3” Riser Flat Pan and to the Insulator End Cap to protect the foam.
3” Riser Flat Pans are used in the Insulator Pan. Pre-existing covers utilizing 3” Riser Flat Pans can be easily converted into Insulator Pans.
2-1/4” x 11-3/4” Foam is used in the Insulator Pan which is equivalent to an R-value of R10.
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall We will embroider YOUR LOGO on the lidFREE!
Burbank Road
FL 34677 Sales Desk: 877-314-2509 Information: 800-969-3706
Local: 813-855-2627
Fax: 813-814-0018
Premium Sample Case w/ Embroidered Logos
(24.5” W x 17.625” D x 5.25” H)
Black 600 denier bag with black handle and shoulder strap. Foam compartments protect samples from damage. (SKU# PMPRMWDSAMPLECASE)
• 3” Snap-N-Lock Panel Sample with Fan Beam
• Permawood Metal Color Fandeck
• 1-1/2” x 1-1/2” Lattice Tube w/ Beveled End Caps
• 2” x 2” Lattice Tube w/ Beveled End Caps
• 2” x 3” Lattice tube w/ Beveled End Caps
• 3” x 3” Fluted Post
• 3” x 3” Post Sleeve
• 2” x 6” Rafter w/ Mitered and Corbel End Caps
• 3” x 8” Rafter Header w/Scallop and Beveled End Caps
FL
Center
Great Oak Drive
FL 33815
Free: 855-431-2642 Local: 863-577-0600 Fax: 863-577-0659
Iberville St., Unit B
225-677-8133
• www.STRUCTALL.com
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall
Permawood Shade Structures have a richly textured woodgrain finish and are available in 6 colors: Graphite Gray, Spanish Brown, Adobe, Sandstone, Desert Sand, and White.
Aluminum Shade Structures by Structall
Lattice covers are truly a landscaping focal point and add value and beauty to any home.
Covering your patio or free-standing, shade structures are an attractive addition to any home.
Aluma-ShieldSM with Teflon® surface protector provides:
• Washability of a semi-gloss finish and decorative appeal of a matte finish.
• Surfaces that repel oil, dust, dirt, and stains - making them easy to keep clean.
Aluminum Shade Structures by Structall
Aluminum Shade Structures by Structall
• Protection from UV and weathering for a longlasting, beautiful new look.
• Products that are resistant to corrosion from sun, salt, and pollution.
• A durable surface that resists chalking and fading.
• A premium coating without the premium price.
Prices Subject to Change Without Notice
A Permawood Shade Structure is an investment in beauty and value. The lattice feature with its sophisticated charm makes it a landscaping focal point for any home.
All units are constructed of an embossed aluminum with a richly textured wood-grain finish. The longterm cost is less than wood, because Permawood won’t burn, attract termites, crack, peel, warp, rot or need constant repainting. The continuous coating process and paint finish are long-lasting and withstand even the harshest conditions.
All components are backed by a Limited Lifetime Warranty and meet ICBO engineering requirements.
• Strong, long-lasting, low maintenance aluminum
• Richly textured wood-grain finish
• Heavy header beam construction
• Paint finish withstands the harshest conditions including: sun, rain, wind and extreme temperatures
• Color-matching fasteners
• Attach to home or construct free-standing
• Open Lattice or Sante Fe Package with solid roof construction
• Custom designed and custom fit
• Posts install with brackets fastened to a concrete slab or embedded in concrete footings
• Virtually maintenance free
• Lifetime Limited Warranty
The solid section of the roof is constructed with Snap-N-Lock™ panels underneath the decorative rafters. The combination of the open lattice and solid cover truly accent the living space.
Choose an open lattice design, solid roof construction, or a combination of both:
Open Lattice - A lattice patio cover provides shade without screening out refreshing breezes.
Santa Fe PackageCombines solid roof construction with lattice accents. Enjoy outdoor living space even when weather isn’t ideal.
• Solid cover can extend entire length of roof or partway.
• Insulated panels give protection from elements
• Patio stays cool and provides excellent shade and protection from sun’s rays.
• Beautiful Southwest accents on the roof trim with exposed rafter tails.
• Posts are 3- piece giving a custom wood look.
AC15LAT019RCWH16
AC15LAT019RCWH20
AC15LAT019RCWH24
AC15LAT019RCWH26
AC15LAT019RCDS16
AC15LAT019RCDS20
AC15LAT019RCDS24 AC15LAT019RCDS26
AC15LAT019RCSS16
AC15LAT019RCSS20
AC15LAT019RCSS24
AC15LAT019RCSS26
AC22LAT019RCWH16
AC22LAT019RCWH20
AC22LAT019RCWH24
AC22LAT019RCWH32
AC22LAT019RCDS16
AC22LAT019RCDS20
AC22LAT019RCDS24
AC22LAT019RCDS32
AC22LAT019RCAD16
AC22LAT019RCAD20
AC22LAT019RCAD24
AC22LAT019RCAD32
AC22LAT019RCSB16
AC22LAT019RCSB20
AC22LAT019RCSB24
AC22LAT019RCSB32
AC26RAF024RCWH12
AC26RAF024RCWH16
AC26RAF024RCWH20
AC26RAF024RCWH24
AC26RAF024RCWH30
AC26RAF024RCDS12
AC26RAF024RCDS16
AC26RAF024RCDS20
AC26RAF024RCDS24
AC26RAF024RCDS30
AC26RAF024RCSS12
AC26RAF024RCSS16
AC26RAF024RCSS20
AC26RAF024RCSS24
AC26RAF024RCSS30
AC26RAF024RCAD12
AC26RAF024RCAD16
AC26RAF024RCAD20
AC26RAF024RCAD24
AC26RAF024RCAD30
AC26RAF024RCSB12
AC26RAF024RCSB16
AC26RAF024RCSB20
AC26RAF024RCSB24
AC26RAF024RCSB30
AC26RAF024RCGG12
AC26RAF024RCGG16
AC26RAF024RCGG20
AC26RAF024RCGG24 AC26RAF024RCGG30
AC38RHD042RCWH16
AC38RHD042RCDS16
AC38RHD042RCDS20
AC38RHD042RCSS16
AC38RHD042RCSS20
AC38RHD042RCSS24
AC38RHD042RCSS30
AC38RHD042RCAD16
AC38RHD042RCAD20
AC38RHD042RCAD24
AC38RHD042RCAD30
AC38RHD042RCSB16
AC38RHD042RCSB20
AC38RHD042RCSB24
AC38RHD042RCSB30
AC38RHD042RCGG16
AC38RHD042RCGG20
AC38RHD042RCGG24
AC38RHD042RCGG30
2” x 6” O/S Rafter / Header Bracket
3” x 8” O/S Rafter / Header Bracket
Rafter Bracket
3” x 8” I/S Rafter Bracket
• 5-Year Manufacturer Warranty
• 6 Color Options Available
• Heavy Duty Construction
• Completely Weather Resistant
• Impact Resistant
• Color Throughout w/ UV Inhibitors
9.375" x 10" x 3.8"
Box includes: 2 injection-molded base half sections, 4 screws, 4 caps, and instruction sheet
Add a Table to Your Aluminum Patio Cover in Seconds
Prices Subject to Change Without Notice
• 2-Year Manufacturer Warranty
• Heavy Duty Construction
• Completely Weather Resistant
• High Strength ASA
• Color Throughout w/ UV Inhibitors
• .200 Nominal Wall Thickness
• Attaches in Minutes w/o Drilling
*Only compatible with 2”x 6.5” Aluminum H-Posts
*Not for use with downspouts
*Not for wood or vinyl patio covers
23" Diameter
Box includes: 2 injection-molded table half sections, 2 thumb screws with wing nuts, and instruction sheet
Prices Subject to Change Without Notice
• Quickly removes dirt, mildew and unsightly stains caused by algae and oxidation
• Easy Spray and Wipe
• No mixing needed - Simply apply the wash and wipe or spray clean with a garden hose
• Works on all Aluminum Patio Covers
• Earth-friendly, non-toxic and biodegradable
Whatever the weather, you can enjoy your outdoor living space with a sense of security. The AluamwoodTM Newport with MAXX PanelTM package combines the elegant charm of an AlumawoodTM Newport patio structure with the strength of the patented Snap-N-LockTM Insulated Panel.
sophisticated charm of a lattice cover. The Santa Fe Package combines the solid roof construction of the Snap-N-LockTM Insulated Panel with beautiful Southwest lattice accents and exposed rafter tails. For maximum protection from the elements, run the panels the entire length of the roof. To provide shade and allow refreshing breezes to pass through, extend the solid roof only partway. www.alumawood.net AlumawoodTM Newport with MAXX PanelTM Installation Guide
Existing Fascia or Structure
3” Wall Header
Rafter Bracket
2” x 6” Side Rafter
Valance Fascia
3” Snap-N-Lock™ Insulated Panel
3” Extruded Gutter
Rafter Tail
Rafter End: Mitered, Beveled, Corbel, Scalloped
2” x 6” Fascia Cover
3x8 Beam
Top Post Bracket
3x3 Post
2” x 6” Post Plate
Bottom Post Bracket
A. Select mounting area on wall. Snap a level chalkline along the wall to locate the bottom of the wall header. Remember, for proper drainage, the panels must be installed at a minimum 1/2” slope per foot of projection.
B. Cut wall header to length. Level extrusion and mark position.
C. Run two beads of caulking along the back surface of the box header where it will meet the existing building or fascia board. Extruded header is recommended for maximum strength.
D. Position the header against the existing building and secure into place using two #10 x 1-1/2” hex head screws every 12” on center. If attached to 1” fascia board, use two #10 x 2” hex head screws in place of #10 x 1-1/2” screws at all rafter tails. If attached to a masonry wall, the header should be fastened with one 1/4” diameter masonry anchor every 16” on center. If enough room, apply a heavy bead of caulking along the top of the header to insure a water tight seal.
Caulk
Caulk
Caulk
Optional: Apply caulk at top of header, if enough room is available.
Optional: Apply caulk at top of header, if enough room is available.
Optional: Apply caulk at top of header, if enough room is available.
Optional: Apply caulk at top of header, if enough room is available.
Optional: Apply caulk at top of header, if enough room is available.
Caulk
Caulk
Optional: Apply caulk at top of header, if enough room is available.
Caulk
Caulk
Caulk
Optional: Apply caulk at top of header, if enough room is available.
Caulk
Optional: Apply caulk at top of header, if enough room is available.
Optional: Apply caulk at top of header, if enough room is available.
A. Posts should be plumb and bottom cut off if necessary to adjust the pitch of the panels for proper drainage and, at the same time, to adjust the header so that it is level from end to end. (Recommended roof pitch is 1/2” for each 1 foot of panel length.)
B. With the posts cut to length, plumb them again and mark the slab attachment. The anchors should be at least 4”away from the edge of the slab or expansion joint and 30” away from any crack. Two 3/8” holes should be drilled through the post brackets and corresponding holes 2-1/2” deep into the slab. Attach the brackets to the slab using the concrete anchors and hammering them into the concrete making sure not to damage the threads.
C. Next, fit each post onto its bracket and fasten with four #14 x 3/4” painted sheetmetal or self-drilling screws.
a. Drill 3/8” hole with the masonry bit at least 3” deep.
b. Clean hole by blowing out debris.
A. Set the 3x8 beam on top of the posts. Make sure the seam side is up and lines up with the wall hanger on the ledger board.
B. Level the beam.
C. Attach the post to the beam using the bracket as shown.
screws
c. Drive the concrete anchor bolt far enough into hole so that at least six threads are below the surface. Do not damage threads.
d. Tighten to 7 foot lbs. with a torque wrench or 2 to 3 turns from finger tight position to achieve the proper anchor setting.
Note: Sideplates should be stuffed with foam.
A. Place the sideplate so that it is centered on the post. Measure 12” from the bottom of the sideplates and drill a 5/8” hole through one side and the foam, making sure not to puncture the other side or dent the sideplate.
B. Place a #14 x 3/4” sheetmetal screws through the sideplate into the post.
C. Measure and mark up 24” on center. Drill a 5/8” hole.
D. Use a level to make sure the sideplate is centered on the post and plumb.
E. Place a #14 x 3/4” sheetmetal screws through the remaining holes.
F. Drill four holes into the sideplates as done previously but for the header/sideplate attachment. (As shown)
G. Place a #14 x 3/4” sheetmetal screws into the four holes.
H. Place the 5/8” plugs into the holes.
I. Repeat these steps on the opposite side and for all remaining posts.
A. Place the first panel into position with the female side facing the outward perimeter of the structure. To avoid scratches on the interior side you have two options:
1.) Roof panels can be lifted over the wall sections top side down, and then turned over when in position.
2.) Cardboard end caps or carpet pieces can be draped over the top channel, so that the panels don’t brush against the metal surface. Check the panel for proper depth in the header and square up to support walls.
B. Fasten panel to the top and bottom of the box header with #8 x 9/16” Tek screws 8” on center.
C. The front and side walls are fastened using a special #10 hex head sheetmetal screw. These should be placed 8” on center on the front wall and at least every 24” on the side walls. The sheetmetal screws should be used in conjunction with a 1/4” x 1-1/2” aluminum washer with neoprene backer. When going into wood framing a 1/4” x 6” lag can be substituted. Fasten the starter panel on the side wall and the outside corner only.
Note: The panel must be free on male edge to snap properly, and screws should not be placed within 4” of panel seam.
D. Run a bead of sealant/adhesive down the top channel of the male side in the sealant reservoir, making sure there are no air bubbles/ pockets. We recommend using Solar Seal 900.
E. Insert the second panel into the header in a level position with the starter panel, using proper handling techniques to avoid scratches.
F. Position panel. Bump panel together until it snaps, bumping from header to overhang. Panels should be snapped together fairly soon after caulking is applied to reservoir. Wipe down top seam of panel to smooth caulk.
G. Repeat with each new panel until finished. The last panel should be squared off on the male side prior to installing to accept valance. Then fasten remaining #10 screws or 1/4” bolts to final side wall and outside corner. (If panels need cleaned, use soap and water.)
H. After all roof panels are installed, run a bead of sealant where the top edge of the wall header meets the panel.
Leave the fastener closest to male side at front untightened so next panel will snap properly.
You can trim the roof two ways:
1) Fascia Trim on all three sides, or
2) Receiver/Gutter in front and Valance on sides.
A. Cut front extrusion to exact width of roof plus 1/8”. Run a heavy bead of caulking along upper inside edge of extrusion.
B. Slip the extrusion over the end of the panels starting at one end and working the extrusion down the width of the roof. Application can be done from the roof or a ladder. A thin putty knife will facilitate application if the fit is tight.
C. Using #8 x 9/16” tek screws at 12” intervals, secure extrusion to the roof front.
D. Seal at all connections with Solar Seal 900 caulking.
E. Drill a weep hole on each end and at each roof panel seam (every 2 or 4 ft.) on the underside of drip edge.
A. Both the valance and fascia trim fit to the outside of the front extrusion. At the end closest to existing structure, cut valance/fascia at appropriate angle to allow for roof slope At the opposite end, to allow for gutter or fascia trim, cut out the flanges 4-3/4”.
Drill a small weep hole on either end of extrusion and at roof panel seams on the underside of the drip edge.
Cut out 4-3/4"
8. Install Alumawood Trim
Note: This step is non-structural and may be modified.
A. Drill several 5/8” holes in one of the 2”x 6” Rafters and attach to the side fascia. This rafter should extend past the side fascia to the desired projection. Repeat for the other side.
B. Cut one of the 2”x 6” rafters so it fits snugly between the two side rafters. Attach to the Fascia Gutter.
C. Attach Rafter Brackets at 24” on center to the front of the front rafter. Use two #10 sheetmetal screws.
D. Attach Rafter Tails to the rafter brackets. Use four #10 sheetmetal screws.
9. Install Downspouts
A. Cut two 1” diameter holes in the bottom of the Gutter Fascia. This should be close to an end post.
B. Place the downspout flange over the hole and fasten with #8 x 1/2” sheetmetal screws.
C. Insert the downspout elbow into one end of the downspout tube and fasten from the sides with #8 x 1/2” sheetmetal screws.
D. Hold the downspout assembly in place to check for proper length and cut as required.
E. Slip the upper end of the downspout flange and fasten from the two sides with #8 x 1/2” sheetmetal screws.
F. Attach the downspout tube to the post with the strap. Fasten on two sides with #8 x 1/2” sheetmetal screws.
A. Due to the advanced design of the Snap-NLock™ panel, it is almost impossible for the panel seams to leak. As in any aluminum roof structure, the most critical point is where the header meets the support wall. For best results counterflashing should be used. If structure has no drip edge, use a flexible flashing such as Flex-Seal.
B. To insure a water tight seam, caulk under edge of counterflashing that rests on roof and secure with a #8 x 1/2” screw at 6” intervals.
C. Use Solar Seal 900 to seal exposed screws and bolt heads. Make sure to completely cover the washers, because of the depression formed when tightening the panels down. Water can sit around the washers and create a problem. Apply caulking along all roof panel connections, outside along all wall module connections to existing structure and along outside edge of base channel.
“L” shaped brakeform counterflashing tucked behind drip edge.
Caulk and secure in front.
“L” shaped brakeform counterflashing tucked behind drip edge. Caulk and secure in front.
Optional Upgrade: Provide the homeowner a more long-term, low-maintenance solution to leaks, by also covering panel connections at header, fascia and gutter; and panel seams with Flex-Seal. The tape remains flexible, while moving with the varying metals of the panel and extrusion as they expand and contract. No fishmouths will form and the bond will remain unaffected. The aluminum backing provides superior UV protection. It also enables the tape to conform to irregular surfaces for a weathertight seal.
A. Secure top channel and base channel to wall panels on interior and exterior. Use #8 x 9/16” tek screws every 16” on center, with two at edge of each module at mullion. If using the adjustable top cap, raise upper assembly until plumb with roof line and secure.
“L” shaped brakeform counterflashing tucked behind drip edge. Caulk and secure in front.
“L” shaped brakeform counterflashing tucked behind drip edge. Caulk and secure in front.
“L” shaped brakeform counterflashing tucked behind drip edge. Caulk and secure in front.
3/4”-1/4”
#10 x 11/2”-5/16” Hex
FAS208101211-0050
FAS208101215-0050
FAS208101216-0050
FAS208101216-0100
FAS210120012-0025
FAS210120012-0100
FAS210120012-0250
FAS210120012-0500
FAS210120012-1000
FAS210120011-0025
FAS210120011-0100
FAS210130012-0025 FAS210130012-0100 FAS210130012-0250
FAS210130011-0025
FAS210120015-0025
FAS210120015-0100
FAS210120015-0250
FAS210120015-0500
FAS210120016-0025
FAS210120014-0025
FAS210120014-0100
FAS210120014-0250 FAS210120014-0500
FAS210130014-0025 FAS210130014-0100 FAS210130014-0250 FAS210130014-0500
FAS210140012-0025
FAS210140012-0100
FAS210140012-0250
FAS210140012-0500
FAS210140012-1000
FAS210140011-0025
FAS210140011-0100
FAS210140011-0250
FAS210140011-0500
FAS210140011-1000
FAS210140015-0025
FAS210140015-0100
FAS210140015-0250
FAS210140015-0500
FAS210140015-1000
FAS210140016-0025
FAS210140016-0100
FAS210140016-0250
FAS210140016-0500
FAS210140016-1000
FAS210140013-0025
FAS210140013-0100
FAS210140013-0250
FAS210140013-0500
FAS210140013-1000
FAS210140014-0025
FAS210140014-0100
FAS210140014-0250
FAS210140014-0500
FAS210140014-1000
#14 x 9” Phillips Truss Head
FAS314290025
FAS314290025-0025
FAS314290025-0050
FAS314290025-0100
FAS314290025-0500 FAS314290025-1000
FAS210150012-0025
FAS210150013-0025
FAS210150013-0100
FAS210150014-0025
FAS210150014-0050
FAS210150014-0100
FAS210150014-0250
FAS210150014-0500 FAS210150014-1000
1/4” I.D. 11/2” O.D. Aluminum Washer w/ Neoprene Backer
FAS514115134
FAS514115134-0025
FAS514115134-0050
FAS514115134-0100 FAS514115134-0500
3/8” I.D. 11/2” O.D. Aluminum Washer w/ Neoprene Backer
5/16” I.D. 11/2” O.D. Aluminum Washer w/ Neoprene Backer
FAS556115134
FAS556115134-0025
FAS556115134-0050
FAS556115134-0100
FAS556115134-0500 FAS556115134-1000
FAS71412TAP2
FAS71412TAP2-0025
FAS71412TAP2-0050
FAS71412TAP2-0100
FAS71412TAP1
FAS71412TAP1-0025
FAS71412TAP1-0050
FAS71412TAP1-0100
FAS71412TAP5
FAS71412TAP5-0025
FAS71412TAP5-0050
FAS71412TAP6
FAS71412TAP6-0025
FAS71415TAP2
FAS71415TAP2-0025
FAS71415TAP2-0050
FAS71415TAP2-0100
FAS71415TAP3
FAS71415TAP3-0025
FAS71415TAP3-0050
FAS71415TAP3-0100
FAS71416TAP2
FAS71416TAP2-0025
FAS71416TAP2-0050
FAS71416TAP2-0100
FAS71416TAP2-1000
FAS73813TAP2 FAS73813TAP2-0025 FAS73813TAP2-0050
1/4” x 21/2” Hex Head Lag Screw Plated
1/4” x 4” Hex Head Lag Screw Plated
1/4” x 5” Hex Head Lag Screw Plated
1/4” x 6” Hex Head Lag Screw
Plated
3/8”
Plated
3/8”
Plated
3/8” x 10” Hex Head Lag Screw
1/4” 20 x 31/2” Hex Head Machine Bolt
1/4” 20 x 4” Hex Head Machine Bolt
1/4” 20 x 41/2” Hex Head Machine Bolt Plated
1/4” 20 x 6” Hex Head Machine Bolt
Prices Subject to Change Without Notice
TRUFAST SIP Heavy Duty (HD) Fastener is designed to attach structural insulated panels (SIPs) and plywood or OSB faced composite boards to steel purlins and bar joists.
• One Drive Bit - T-30 Star Drive Bit included with purchase of full pail of fasteners (full pail consists of 500 fasteners for 6” SIP HD, and 250 fasteners for 8” and 9-3/4” SIP HD).
• Low profile, pancake head provides excellent pull-through resistance
• Special drop-nose drill point designed to drill and tap nested steel purlins (16-10 ga.) or bar joists (max. 1/4” thick)
• Spiral grooved threads to minimize binding torque
• Large diameter wire for increased shear resistance
6-Lobe T-30 Torx Drive
Threads Per Inch With Spiral Grooves Min. Grip Length
Prices Subject to Change Without Notice
TRUFAST SIP Light Duty (LD) Fastener is designed to meet the fastening requirements of Structural Insulated Panels into wood and steel (18 gauge max.) substrates.
• Drill Point for quick penetration
• Large Pancake Type Head, T-30 Torx Drive.
• One free Drive Bit with each purchase of a full pail of fasteners.
• Thread design to maximize performance and increase pull out value.
• Tru-Kote™ epoxy coating exceeds FM Standard 4470
Torx Drive
Two-Flute Formed Drill Tip 10 Single Lead Threads/Inch
#8 x 1/2” Wafer Head Tek Screw Self-Drilling
#8 x 9/16” Pointed Wafer Head
#8 x 1” Pointed Wafer Head
This type of screw is best used when attaching extrusions, installing window flanges to extruded openings and for heavy gauge steel framing.
Use pointed wafer head screws when attaching wire lath, asphalt shingles, vinyl siding, break metal accessories, high-hat channel, and electric boxes to metal skin and light gauge steel framing.
Use pointed wafer head screws when attaching wire lath, asphalt shingles, vinyl siding, break metal accessories, high-hat channel, and electric boxes to metal skin and light gauge steel framing.
Buildex 1/4” x 5” - 3/8” Hex Washer Head
Buildex 1/4” x 6” - 3/8” Hex Washer Head
Buildex 1/4” x 8” - 3/8” Hex Washer Head
Blazer 1/4” x 5” - 3/8” Hex Washer Head
Blazer 1/4” x 6” - 3/8” Hex Washer Head
Blazer 1/4” x 8” - 3/8” Hex Washer Head
PRO-SEAL 7500 Professional Grade Silicone Sealant is a high performance, industrial grade silicone sealant. The neutral cure (oxime), low modulus allows for excellent joint movement capailities (±50%), and weatherability with a life expectancy of 50 years. The silicone won’t dissolve foam, is highly UV resistant, and is permanently flexible. The caulk skins over in just 10 minutes, and completely cures within 24 hours.
PRO-SEAL 7500 bonds to almost any substrate, including PVC (vinyl), is non-corrosive, will not shrink or crack, and is low in odor.
Cross-Section of Snap-N-Lock Panel
• PROFESSIONAL GRADE SEALANT
• TEMPERATURE RANGE:
-62º F TO 350 º F CONTINUOUS USE
-62º F TO 400 º F INTERMITTENT USE
• PERMANENT FLEXIBILITY
• WILL NOT SHRINK OR CRACK
• CURES IN 24 HOURS
• 50 YEAR LIFETIME EXPECTANCY
• Superior performance with the Snap-N-Lock Panel System
• Plastic tube with removable tip
• Will not shrink or crack
Prices Subject to Change Without Notice
• HIGH PERFORMANCE SEALANT Alternative to silicones & urethanes
• ELONGATION 300 - 400%
• STRONG ELASTIC SEAL
• FLEXIBLE: 40ºF - 300ºF
• SUPERIOR ADHESION to vinyl, brick, metal & cedar
• PAINTABLE
NPC Solar Seal #900 Terpolymer rubber, adhesive/sealant is a high performance product designed to bond and seal right angle joints formed by building materials.
Solar Seal #900 does not require a primer and performs equally well on non-pourous and porous surfaces such as vinyl, ceramic, glass, metal, brick, concrete, wood and cedar.
Exceptional fade resistance, adhesion, weatherability, toughness, and elasticity are inherent properties of the basic polymers used to produce SOLAR SEAL #900.
Geocel 2315LRF is a single component, brushable elastic sealant with rubber-like flexibility. 2315LRF is a permanent solution for roof leaks, and will stop leaks immediately even in wet conditions. It has superior adhesion to asphaltic and metal surfaces, SPF, as well as EPDM, Hypalon, Neoprene, TPO, PVC and other prefabricated sheets.
Each roll contains application instructions and a scouring pad.
For use on virtually all roofs, RoofSeal/OneStep Tape incorporates Eternabond’s advance MicroSealant Technology and features a UV stable backing.
RoofSeal/OneStep creates a waterproof, moisture and air tight barrier with no additional sealing required. RoofSeal/ OneStep remains flexible to temperatures as low as -70°F making it virtually impossible to thermally shock the roof causing a leak.
RoofSeal/OneStep permanently bonds to materials such as EPDM, TPO, most PVC, CSPE/Hypalon, CPE, SBS, APP modifies, asphalt BURs, coal tar BURs, all metal roofs, tiles, shingle, aluminum, Galvanized steel, gypsum board, wood, polyethylene, propylene, polystytrene, fiberglass, brick, concrete, masonry, OSB, etc.
Eternabond RoofSeal/OneStep Tape is used to seal roof joints (seams) and tears, flashings, copings, skylights, gutters, etc. Perfect for repairing and restoring roofs on mobil homes and RVs. Very flexible, RoofSeal/OneStep seals to itself so it can be cut and folded around an object, as if wrapping a present.
Surface must be clean and dry; free of loose rust and scale, dust, talc, and dirt. Oil, grease, and other contaminants should be removed with a suitable solvent/cleaner.
Total Thickness
Adhesion
Low temp flexibility
Application temp
Temperature range
Pliability
Water vapor test (ASTME 96B)
Permanence
Elongation
Tensile break PSI
Shelf life
35 mils (+/- 2 mils)
20lbs+/in width
Excellent >150° to -25° with optional primer
-70°F - >200°F
No cracks in membrane
.005 grms/100” sq./24hrs/100°F .001 perms maximum
>700% +/- 100
4500 PSI +/- 500 PSI
Up to 5 years
Prices Subject to Change Without Notice
• Aluminum backing is more moldableconforms better to irregular surface features for weather-tight seals
• Excellent For Flashing
• No Messy Sealant
• Stays Flexible
• Aggressive Grip
• Superior Adhesion
• Assure Immediate Leakproof Results
• Butyl Adhesive/Sealant Has No Asphalt, Solvent
• Easy, Fast Application
• No Harmful VOC’s
• Ideal Adhesive/Sealant Thickness
• Non-reinforced 35 mil adhesive tape
• Adheres aggressively to most smooth surfaces, including plywood
• Self-seals around nails, staples and other fasteners
• Provides a dependable weatherproof barrier over a wide range of weather conditions
• Release liner on one side and release film on the other
• Ideal for light-duty applications
DoubleBond™ is designed for sealing applications requiring an adhesive surface on both sides. It can be used as a self-sealing gasket replacing messy caulks and is ideal for use around skylights, windows and vents.
Peel & Seal® is the original, self-stick roll roofing specifically designed for low slope residential and commercial applications. Composed of a patented formula (consisting of laminated aluminized foil, highdensity polymer films and a thick layer of rubberized asphalt), Peel & Seal® provides a long lasting, durable, maintenance-free roofing surface.
From dormers, residential sunroom additions, “open” porches, and mobile home roofs, to industrial and agricultural buildings where low slope roofs are common place, Peel & Seal® is an excellent solution for these applications. The self-adhering, weatherproof, reflective surface not only forms a highly effective barrier to the elements, but also limits solar heating to help keep the temperature of building interiors significantly cooler.
Applying Peel & Seal® is easy. No tar, torches, mops, glues, tapes, or fasteners are required... a utility knife and hand roller are the only tools needed. Following preparation of the surface, simply peel off the release liner, unroll Peel & Seal® to the proper length.
Peel & Seal® is perfect for hundreds of uses ranging from full-roof applications to patching gutters and vent pipes. Fully pliable and providing a secure seal at edges, corners and over gaps, it is ideal for roof areas that are often difficult to waterproof, including locations where ducts, vents, chimneys, or air conditioning units either protrude through, or are roof mounted.
Peel & Seal® – the original, maintenance-free, energy efficient, economical, self-sealing roll roofing you can count on for any low slope/low pitch application and warranted by MFM for 10 full years!
Prices Subject to Change Without Notice
Peel & Seal® PowerBond™ White is a 45 mil patented cross-linked waterproofing tape with a highly aggressive PowerBond™ adhesive system that adheres in cold temperatures down to 25°F.
Peel & Seal® PowerBond™ White is specifically designed for low-slope roof applications and is ideal for mobile homes, trailers, RVs, sun rooms, and over metal roofs.
Peel & Seal® PowerBond™ White uses a highly aggressive asphalt adhesive that is combined with a proven UVstable outer film to form a long-lasting protective barrier. The end result is a seal that prevents leaks and reduces storm water damage.
The product is easily installed, even at temperatures as low as 25°F. Simply remove the release liner, press into place and finish by rolling the seams with a hand roller.
Peel & Seal® PowerBond™ White can be cut using scissors or a utility knife.
Peel & Seal® PowerBond White may be left exposed to sunlight indefinitely. The unique formula provides water/ weather proofing, sticks to most surfaces for a sealing bond, self-seals around fasteners, conforms to odd shapes, and is backed by a 12-Year Limited Warranty.
Prices Subject to Change Without Notice
P3 Pool & Patio
SCR1P31814483
SCR1P31814603
SCR1P31814603
SCR1P31814723
SCR1P31814783
SCR1P31814843
SCR1P31814963
SCR1P318141023
SCR1P318141083
Introducing P3 – Pool & Patio Plus, a premium hybrid pool and patio product.
Increased strength & protection without compromising visibility.
P3 - Pool & Patio Plus is the latest, and first, of its kind innovation from ADFORS for the pool & patio market. This new product features a unique hybrid construction using both polyester and fiberglass yarns. This combination gives P3 increased strength and protection, while maintaining excellent outward visibility, which can be lost with traditional, just polyester, products.
P3 is easier to install for contractors and also comes backed by a 7-year warranty!
Additional features & benefits of P3 include:
• 18x14 Mesh
• Thinner profile
• Stronger than standard 18x14 screen
• After 10 year weathering simulation, P3 retains 60% more strength than standard screen
• More openness compared to polyester products for more airflow, increased light and reduced wind load on cages
P3
Heavier screening fabric designed for large areas such as pool enclosures, screened-in patios, and porches.
UV stable coating to ensure long-lasting color and flexibility. The screen will not stretch or shrink, and will maintain its physical properties even under extreme temperatures.
Keep grass and debris out
SCR11814363
SCR11814483
SCR11814603
SCR11814663
SCR11814723
SCR11814783
SCR11814843
SCR11814903
SCR11814963
SCR118141023
SCR118141083
SCR12020483
SCR12020603
SCR12020723
SCR12020843
SCR12020963
SCR120201083
ADFORS Glass Screen is a fiberglass screen that is laminated for use on the bottom part of an enclosure. It is normally used from the chair rail to the pool and patio deck.
54x18 Mesh - Fiberglass Screen
SCR12030363
SCR12030483
SCR12030603
SCR12030723
SCR12030843
SCR12030963
ADFORS Sun Guard Solar Screen can help control the damaging effects of the sun. While filtering light and heat from the exterior, the unique weave is specifically designed for better visibility without distortion from the interior.
This product will prevent damage from household pets and children who push against the screening. Pet Resistant Screen still allows for excellent outward visibility and airflow.
Although Pet Resistant Screen is much heavier than traditional screening, it can be easily installed in any door or window.
Pet Resistant Screen is the perfect companion product for our insulated kickplates. Screen rooms utilizing aluminum or luran kickplates and Pet Resistant Screen will withstand the daily wear imposed by your beloved pets - translating into years more enjoyment of your screen room.
*Recommend 0.290 Spline for Super Screen
SCR51714843
SCR51714963
No-See-Um Screen™ comes with all of the advantages of Super Screen™. It is made out of the same technological, advanced fiber that goes into Super Screen™ so you get a product that is highly tear resistant. It is tough enough to withstand dogs and cats as well as other pets. It is puncture resistant with a ball burst test of 250 lb per square foot. It also protects against the harmful ultraviolet rays of the sun. It retains its color and maintains that new screen looks for years. It contains a biocide that is safe for you and your pets and prevents mold and mildew buildup on your screen. It is also lead free, phthalate free and meets all Green Guard Gold safety standards to ensure our products are free from harmful, volatile organic compounds (VOC’s) and safe for you, your family, and pets.
NO-SEE-UM SCREEN™
No-See-Um Screen™ is our 20/20 mesh size is perfect for preventing even the tiniest of insects from entering your screen enclosure while maintaining excellent visibility and airflow.
TEN-YEAR LIMITED
Super-Screen™ No-See-Um Screen™ comes with an industry best 10 Year limited warranty.
cycles/with no added weight)
EZ Roller with ergonomically designed easy grip handle. Comes with three screen roller sizes and blade for built-in utility knife.
• Reduces the risk of arm, shoulder and wrist damage
• Designed by professionals for professionals
• Ergonomically designed to reduce fatigue
• Small splines of different configurations
• Rolls and trims a multitude of materials
• Virtually every carpet and linoleum
• Fast smooth operation of mechanisms
• Quick change of standard blades
• Safety heel for hand protection
• Fast, simple blade replacement
• Ergonomically designed to provide the greatest control with the least amount of effort
• High impact body and rollers
• Virtually every round spline
• Multiple use tools in one light compact unit
• Every flat spline
• Lightweight
• Sealed life time bearings
• Uses standard blades
• All corrosion resistant parts
The EZ Roller is a superior two-in-one tool which allows you to work faster and safer. The Ergonomic design of the tool - the overall shape of the grip, the placement of the axle, and the heel rest provide a more perfect transfer of the user’s force from his or her shoulder, arm, and wrist without the fatigue and potential muscle and nerve damage associated with other tools. Life-time warranty against defects in the product.
This tool comes with the most widely used rolling wheel installed. The two other wheels supplied provide additional uses to cover a wide spectrum of uses. These primary uses are as follows: R Wheel - for the larger round vinyl spline materials and carpet. S Wheel - for the standard flat spline materials and carpet. W Wheelprimarily for the small varieties of plastic, vinyl and odd shaped specialty splines used in the window screen, vinyl window and sliding glass door markets.
Aluminum Handle Spline Roller, comes standard with (1) .165 Pre-Roll Wheel with Bearing and (1) .165 Flat Wheel with Bearing
Prices Subject to Change Without Notice
Skylights should be centered in the width of the panel, within 1 ft. of the sides. At customer request, skylight openings can be pre-cut and framed at the factory (see Skylight Wrap).
When installing, surface should be clean and dry. Apply 4” DoubleBond™ tape on all sides of pre-framed opening. Start with the gutter side and cut so it extends 4” on either side of the opening. Make sure you roll the DoubleBond™ tape until flat. Apply either the left or right side next, finishing with the header end. All pieces should overlap the previous piece.
Carefully position skylight over opening and secure using #8 x 1/2” Tek screws 8” on center. Place White or Foil sealant tape over top edge of flange making sure screws are covered. Apply gutter end first, then sides, and finally the header end, making sure all pieces overlap the previous piece.
Skylight Wrap for strengthening the skylight opening.
Extrusion sizes available in 3”, 4”, and 6” depths.
This skylight is recommended for roof pitches 0:12 to 68:12.
Prices Subject to Change Without Notice
Sash
Corrosion-proof .062” extruded aluminum with welded corners to guarantee a leakproof seal. Top side of sash has an easy-release continuous hinge for quick sash replacement. Powder coated for extra durability.
Glass
Florida Product Approval #
FL15592-R7
Skylight features a condensation gutter to channel moisture off of the glass.
Deck Mount Flashing
Extra wide flange with pre-drilled holes for easy installation. Powder coated for extra durability.
Interior
Pre-finished white poplar wood interior with decorative molding. Thick foam gasket around the perimeter seals the sash to the curb to keep it water-tight.
• Meets the stringent requirements of the Florida Building Code
• High performance glass LoE-240 argon-filled glass
• Drywall return sized for both 1/2” and 5/8” drywall
• .062” extruded aluminum exterior with welded corners
• Integrated 4” flange with pre-drilled screw holes
• ENERGY STAR® Certified in all 50 states
• Replacement Sash Available - see model
• Tempered, LoE-240 argon-filled
• Exterior is powder coated inside and out for superior durability
• Pre-finished white poplar wood interior
• 25-Year non-prorated limited warranty on insulated glass against seal failure
• 10-Year limited warranty against defects in workmanship and materials
Air Infiltration Test - ASTM E 283
Air at 1.57 psf - 0.02 cfm/ft2
Air at 6.24 psf - 0.04 cfm/ft2
Water Infiltration Test - ASTM E 331
Water @ 12 psf (2.45”) - Passed / No Entry for 15 minutes
Uniform Load Structural Test - ASTM E 330
Design Load +80 psf , -80 psf
Meets performance levels specified in TAS 202
Kickplate Coil
CA2424WHTWHTCE-LF
CA2424WHTWHTSM-LF
CA2424BRZBRZCE-LF
CA2424BRZBRZSM-LF
Kickplate Coil
CA3016WHTWHTCE-LF
CA3016WHTWHTSE-LF
CA3016WHTWHTSM-LF
CA3016IVYIVYCE-LF
CA3016IVYIVYSE-LF
CA3016IVYIVYSM-LF
CA3016SANSANCE-LF
CA3016SANSANSE-LF
CA3016ADBADBCE-LF CA3016ADBADBSE-LF
CA3016BRZBRZCE-LF
CA3016BRZBRZE-LF
CA3016BRZBRZSM-LF
• Helps protect windows from damage when closed.
• Shades window openings to help decrease cooling bills.
• Many colors to choose from.
• Easy to open and close.
• 2 week lead time from order date.
The, All New, Perfect-Breeze Premium Screen Doors are here! Engineered to be durable AND attractive, Perfect-Breeze Screen Doors come standard with features that other screen doors don’t even offer. Look at some of the highlights and see why we call these screen doors Perfect-Breeze
R Full 1¼” Extruded Aluminum Mainframe Assembled with Extra Heavy-Duty Corner Keys.
R 4 Heavy-Duty Hinges with Bronze Bushings.
R 5 Available Colors - Adobe, Sandstone, Bronze, Ivory, & White.
R 3 Available Kickplate Textures - Stucco, Cedar, & Smooth - to coordinate with the screen room kickplate.
R Clean-Routered Interior Extrusion.
R 16” NeveRattle© .030 Aluminum Kickplate.
R Prescreened with 18x14 Mesh Fiberglass Screen Optional: Super Screen, Super Screen No-See-Um, Pet Screen, P3
R Exterior Flat Spline - has a better hold on the screen, shows a clean interior profile and matches the spline used on the screen room.
R Thicker Push Bar Attached with Internal Screw Bosses, not rivets.
R Custom Widths Available.
R Adjustable Door Sweep Expander Included.
R Grey Pile Weatherstrip Included - Keeps bugs out and prevents banging when door is being closed.
R Heavy-Duty Door Hardware and Closer Included.
R Fully Boxed to prevent shipping damage on our truck and yours.
R Door Sweep Options: Standard Rubber Sweep or Black Pile w/Fin
PATSD3PHPBOST3WLH
PATSD3PHPBOST3WRH
PATSD3PHPBOCD3WLH
PATSD3PHPBOCD3WRH
PATSD3PHPBOSM3WLH
PATSD3PHPBOSM3WRH
PATSD3PHPBONK3WLH
PATSD3PHPBONK3WRH
PATSD3PHPBOST3ILH
PATSD3PHPBOST3IRH
PATSD3PHPBOCD3ILH
PATSD3PHPBOCD3IRH
PATSD3PHPBOSM3ILH
PATSD3PHPBOSM3IRH
PATSD3PHPBONK3ILH
PATSD3PHPBONK3IRH
PATSD3PHPBOST3SLH
PATSD3PHPBOST3SRH
PATSD3PHPBOCD3SLH
PATSD3PHPBOCD3SRH
PATSD3PHPBOSM3SLH
PATSD3PHPBOSM3SRH
PATSD3PHPBONK3SLH
PATSD3PHPBONK3SRH
PATSD3PHPBOST3ALH
PATSD3PHPBOST3ARH
PATSD3PHPBOCD3ALH
PATSD3PHPBOCD3ARH
PATSD3PHPBOSM3ALH
PATSD3PHPBOSM3ARH
PATSD3PHPBONK3ALH
PATSD3PHPBONK3ARH
PATSD3PHPBOST3BLH
PATSD3PHPBOST3BRH
PATSD3PHPBOCD3BLH
PATSD3PHPBOCD3BRH
PATSD3PHPBOSM3BLH
PATSD3PHPBOSM3BRH
PATSD3PHPBONK3BLH
PATSD3PHPBONK3BRH
Stucco Stucco Cedar Cedar Smooth Smooth No Kickplate No Kickplate Left Right Left Right Left Right Left Right
Stucco Stucco Cedar Cedar Smooth Smooth No Kickplate No Kickplate Left Right Left Right Left Right Left Right 362.48
Stucco Stucco Cedar Cedar Smooth Smooth No Kickplate No Kickplate Left Right Left Right Left Right Left Right 362.48
Stucco Stucco Cedar Cedar Smooth Smooth No Kickplate No Kickplate Left Right Left Right Left Right Left Right 362.48
Stucco Stucco Cedar Cedar Smooth Smooth No Kickplate No Kickplate Left Right Left Right Left Right Left Right 362.48
Perfect Breeze Screen Door w/ Medium Magnador Pet Door
PATSD3PHPBOST3WLHPDM
PATSD3PHPBOST3WRHPDM
PATSD3PHPBOCD3WLHPDM
PATSD3PHPBOCD3WRHPDM
PATSD3PHPBOSM3WLHPDM
PATSD3PHPBOSM3WRHPDM
PATSD3PHPBOST3BLHPDM
PATSD3PHPBOST3BRHPDM
PATSD3PHPBOCD3BLHPDM
PATSD3PHPBOCD3BRHPDM
PATSD3PHPBOSM3BLHPDM
PATSD3PHPBOSM3BRHPDM
Breeze
w/ Large Magnador Pet Door
PATSD3PHPBOST3WLHPDL
PATSD3PHPBOST3WRHPDL
PATSD3PHPBOSM3WLHPDL
PATSD3PHPBOSM3WRHPDL
PATSD3PHPBOST3BLHPDL
PATSD3PHPBOST3BRHPDL
PATSD3PHPBOSM3BLHPDL
PATSD3PHPBOSM3BRHPDL
PATSD28PH2WLH8
PATSD28PH2WLH14
PATSD28PH2WRH8
PATSD28PH2WRH14
PATSD28PH2BLH8
PATSD28PH2BLH14
PATSD28PH2BRH8
PATSD28PH2BRH14
PATSD3PH3WLH8A
PATSD3PH3WLH14A PATSD3PH3WRH8A
All of our screen door kits are of a professional contractor quality, using long lasting powder coat paint, an aluminum tube & aluminum stamped mounting brackets.
• Stainless Steel and Aluminum Construction
• Powder Coat Paint
• Adjustable Speed Piston
• Rust-Resistant Stainless Steel Rod
Screen Door Kit Includes:
• Contractor Grade Screen Door Closer
• Molded Jamb Bracket
• Door Handle with Push Button
• Door Bracket
• Strike Plate
• Mounting Hardware (not pictured)
• Easy operation - perfect for the elderly /disabled
• Patented hold and release closer
• Hold open from any position
• Release by lightly bumping door outwardly
•
•
• Molded Jamb Bracket
• Door Handle with Push Button
• Door Bracket
• Strike Plate
• Mounting Hardware
• Door Bracket
• Strike Plate • Mounting Hardware
Now available in NEW Bronze (dark brown) in addition to the original white color. Bronze shows less dirt and wear in heavy use environments like kennels and matches bronze aluminum screen enclosures.
NEW High Power Magnets. 30-40 times greater holding power than the regular magnets. Great alternative for high wind and heavy use. Strongest magnetically held door on the market.
Durable and Simple. The Magnador™ Two-Way Pet Door is a simple to install product at a value price. Durable High Impact Polystyrene resists chewing and is tough, yet forgiving for hard headed dogs. Integrated locking knobs eliminate misplaced or damaged sliding panels or covers.
Magnador™ Two-Way Pet Doors are used extensively in a variety of situations: kennels, doors, screen doors, metal buildings, barns, screen porch enclosures, lanais, pool enclosures, garage doors and dog houses.
Close fit between swinging panel and frame keeps out unwanted pests and bugs. Magnet holds door in place to prevent debris and critters from entering. Screw type locking knobs secure door for entry or exit. No sliding panels to misplace or damage.
Sturdy construction makes this door ideal for hard use. Replacement parts assure long lasting installation and easy repairs.
Two sizes available:
• Medium (11” x 13”) for small and medium size dogs (20-60 pounds).
• Large (13” x 19 3/4”) for medium and large size dogs (50 plus pounds).
Equipment required for installation: Pencil, Masking tape, Straight edge, Phillips screwdriver, Exterior caulk, 1/8” and 3/8” drill bits, Electric Drill, Saber Saw
CWS WDCGW $50
PGT WDPGW $50
PGT and CWS warranty for insulated seal failure: After 1 year, neither company will send a service tech to customer homes to replace glass. Structall will package the glass and ship to the manufacturer for replacement.
Company Name Purchase Order Signature Date
Screen Upgrade Options
ADFORS Pool & Patio 18x14
ADFORS Pet Screen
54x18 Adfors Sun Screen
20x20 SBS Pool & Patio Screen
20x20 Super Screen NoSee Um Outswing
17x14 Super Screen
Company Name
Purchase Order
Signature Date
Finished Opening Dimensions
Screen Upgrade Options
ADFORS Pool & Patio 18x14
ADFORS Pet Screen
54x18 Adfors Sun Screen
20x20 SBS Pool & Patio Screen
20x20 Super Screen NoSee Um
17x14 Super Screen
Choose a Kickplate
Aluminum extrusion, such as gutters, can develop unsightly dark streaks. The streaks won’t clean off using soap and water. They are caused by algae, dirt, and other particles washing onto the extrusion and electrostatically bonding to the anodized metal. This phenomena is also known as “tiger striping” or “zebra striping”.
Structall recommends the use of specialized cleaners to remove the streaks:
• F-13 Gutter Grenade
• Gutter Zap
• Citrus Gutter Cleaner and House Wash
• Mean Green
• Spray Power
• Simple Cherry
• Citri Kleen
• Gutter Shock
• Purple Power
• Simple Green Gutter Clean
You will need a scrub brush with an extension pole as well as a water hose with standard sprayer. A pressure washer can be used if available.
*Use as directed.* Some of the listed cleaners contain butyl and other chemicals that can damage the paint on the extrusion as well as anything that the cleaner may come in contact with. Dilute the cleaner as prescribed and use appropriate brushes and protective gear.
Prices Subject to Change Without Notice
Structall recommends panels with Adobe and Bronze skins be used as the bottom skin (install down) or in the room-side position. White is the best color to reflect the rays of the sun, reducing heat buildup and related expansion problems inherent with all aluminum products. Structall’s White coated panel skins are certified by ENERGY STAR® to meet or exceed their requirements for Solar Reflectance per ASTM C1549 and Emittance per ASTM C1371.
Accelerated thermal bowing can occur if a Adobe or Bronze panel skin is exposed to the sun. On stress skin panels such as ours, this effect is caused by the dark coated exterior absorbing heat rather than reflecting it, while the interior-facing skin of the panel stays cool. The overheated exterior-facing skin expands, causing the panel to bow and possibly delaminate.
With that in mind, do not store or stack Adobe or Bronze panel skins facing the sun.
A white, weatherproof coating over the dark top skin or appropriately installed shingles can greatly reduce, if not eliminate, thermal bowing.
*Thermal bowing does not represent a manufacturing defect. Any damage incurred through incorrect storage or installation will void the warranty.
/ White Ivory / White Desert Sand / White Sandstone / White White / Ivory Ivory / Ivory Desert Sand / Ivory Sandstone / Ivory White / Desert Sand Ivory / Desert Sand Desert Sand / Desert Sand Sandstone / Desert Sand
White / Sandstone Ivory / Sandstone Desert Sand / Sandstone Sandstone / Sandstone
White / Adobe Ivory / Adobe Desert Sand / Adobe Sandstone / Adobe
White / Bronze Ivory / Bronze Desert Sand / Bronze Sandstone / Bronze
Prices Subject to Change Without Notice
Structall does not suggest or endorse the manufacture of the Snap-N-Lock™ Panel in lengths greater than 25ft. Natural, heat related, expansion of the panel skins can cause buckling and cracking at the mid point fastener lines.
Panels greater than 32ft. are not covered by Structall’s Limited Warranty.
For those who wish to paint Rigiwall Panels, the manufacturer suggests using any paint made for vinyl.
Sherwin Williams Durations paints or any solvent-based paint work well. No primer is required using these paints.
Follow the paint manufacturer’s directions for application.
Thoroughly clean the panels prior to painting. Sales: 877-314-2509 FAX: 813-814-0018 info@structall.com
Prices Subject to Change Without Notice
Structural insulated panels are not sound proof. Sounds will pass through SIPs and sometimes will be amplified. For instance, a typical steel SIP home will have the internal noise level of a typical brick home. However, room additions that are “unfinished” and do not employ furring + drywall or other sound deadening materials and techniques will have a higher internal noise level than that of a typical home interior. Taps and knocks on the outside of an “unfinished” SIP structure will be audible.
Like all building materials, temperature has an effect on structural insulated panels. SIPs construction will expand and contract as the temperature warms and cools. During rapid temperature changes, SIP construction may produce popping sounds if roof joints and beams have not been installed properly. If the structure is “unfinished”, the sounds can be that much more noticeable.
Use these techniques to reduce sound levels within a SIP structure. It is important to lessen the effect of heat on the structure, create buffers between joints, and airspace between the exterior walls and interior finish.
1. Apply a vibration absorbing underlayment directly to roof panels before installing roof finish.
2. Use glue or gasket material at the tops of beams and walls.
3. Furring interior walls with sound deadening material or furring strips before installation of drywall.
4. Use a back ventilated roof finish.
For those who wish to apply Elastomeric Roof Coating to a panel roof, Structall suggests using an acrylic coating.
Follow the coating manufacturer’s directions on when and how to apply their coating to achieve best adhesion, including their directions for cleaning the roof.
The most important step is to thoroughly clean the roof using an appropriate roof cleaning solution and a scrub brush. The panels must be clear of any dirt, debris, mildew, and chalk.
Structall’s Steel Snap-N-Lock™ Panel skins are cut using a shear press. This method results in a clean cut without generating metal chips that can cause rust blemishes on the panel paint finish.
Drilling, cutting, and grinding a steel panel at the jobsite will produce metal filings that will magnetically adhere to the skin of the panel. If these shavings are not removed from the fascia of the panel, the small bits of metal will corrode and blemish the finish. The result is only cosmetic and will not affect the longevity of the panel. However, to avoid the inevitable blemishes to the paint finish caused by the rusting filings, wipe off the panel with a cloth or softbristled brush immediately after modifying the panel.
Wipe off all steel panels at a jobsite (including unmodified panels) before installation to remove any debris that may have blown onto the panels.
If the metal filings were not removed before installation and speckles of rust begin to show on the panels, use cleaning products such as Spic and Span® or Soft Scrub® along with a nylon scrubbing pad and water to clean off the rust filings. The paint finish will likely be stained by the rust but the cleaning will have removed the source of the discoloration.
Warranties
• 1 fan per fan beam
• 40lb Max weight per fan beam
Prices Subject to Change Without Notice 4" SNAP-N-LOCK
Fan Beam Installation Detail COMPOSITE PANEL
CONT. 1 1/2" x 3" x .050 ALUM. FAN BEAM
EXTRUSION OR EQUAL
ELECT RICAL WIRING
N.E.C. APPROVED ELEC.
CONDUCTOR
FASTEN FAN OR LIGHT PER MANUF., SPECS. SCREWS TO BE SELFTAPPING & PENET RATE FAN BEAM
FAN OR LIGHT FIXTURE
(COMMERCIAL SCALE
FIXTURES REQUIR E
ADDITIONAL STRUC TURAL
SUPPORT )
• #10 Self-tapping SMS, 12 TPI and 1-1/2” OD Seal washer w/ neoprene insert
• Bottom of fan beam sits 2” from top of all panels
• Fastener must extend 1” into fan beam Sales: 877-314-2509
Sales: 877-314-2509 FAX: 813-814-0018
info@structall.com
Prices Subject to Change Without Notice
For support capacity and fastener information, refer to our Fan Beam Support Details prepared by Engineering Express. The details can be found at structall.com under ‘Engineering’ (FBC or IBC Engineering). Sealed copies of the details can be purchased directly from Engineering Express.
www.engineeringexpress.com/product/structall-fan-beam-support-details-23-69357/
Install an electrical box to attach the fan.
The panel should be prepped with two holes prior to installation (3-1/2” hole through panel skin and 1/2” foam to fan beam, then 1-1/2” hole through one side of fan beam).
Use a local code approved pancake box. Attach to fan beam and feed wire through. Finish with a local code approved Romex connector and wire nuts.
There are various grommets and pancake electrical boxes sold at Lowe’s and Home Depot that serve to protect the wiring exiting the fan beam. Once installed, the electrical box assembly effectively protects the wiring exiting the panel’s fan beam.
Fans are typically boxed with long screws for fastening to an electrical box. You may need to cut them short or use shorter screws to attach the fan securely.
*Adhere to local code when installing ceiling fans. This guide does not supersede local code.
Example of a simple grommet that can be used to protect the wiring:
Example of a ½” deep ceiling fan box:
Commercial Electric 1/2 in. Deep 5.9 cu. in. Ceiling Fan Box with Metal CoverCMB50 - The Home Depot
During construction, it is possible to have gaps between panels or damaged foam. You can use expanding foam to seal the offending voids.
Structall tested several off-the-shelf expanding foam products:
• Great Stuff Gaps & Cracks
• Great Stuff Window & Door - Insulating
• Great Stuff Window & Door
• Loctite Tite Foam Gaps & Cracks
• Loctite Tite Foam Window & Door
We observed that the expanding foams did not react with nor melt the EPS foam used in our panels.
The Great Stuff products were the most user-friendly.
We recommend securing the panels in place prior to applying the expanding foam. Securing the panels first eliminates the possibility of the expanding foam pushing panels or other components out of alignment.
If you intend to use the expanding foam to seal a butt joint between panels, we recommend using Great Stuff Gaps & Cracks since it does not expand as dramatically and will not push the panels away from each other.
Expanding foam is easily trimmed with a serrated blade after fully curing.
We DO NOT recommend the use of “large gap” expanding foam products.
*Follow application directions provided by the manufacturer.*
Prices Subject to Change Without Notice
STRUCTALL BUILDING SYSTEMS, INC. warrants to the Purchaser that Structall’s Metal Panels products will not delaminate as a result of a defect in materials or workmanship for a period of 10 years from the date of the purchase. In the event of a valid claim, Structall will provide replacement panels.
This warranty does not cover damage by willful abuse, normal weathering, negligence or failure to provide normal maintenance and cleaning, exposure to industrial pollution, salt spray or chemical atmosphere, damage by physical abuse, abrasion, impact or other force, or an act of nature, such as fire, lightning, windstorms, hailstorms or causes beyond Structall Building Systems, Inc.’s control.
This warranty does not cover use of the product in applications beyond the design limits as spelled out in the Structall engineering publications. Installation not in strict compliance with the Structall installation instructions shall also void the warranty.
Both steel and aluminum clad panels are subject to corrosion and are specifically not covered beyond any warranty provided by the coil manufacturer. Structall recommends a light pressure wash every year for the underside of any panel roof or panel wall section exposed to, or near by, a salt water environment or a swimming pool or spa where chlorine is used.
This warranty does not cover infestation by insects, rodents or other pests. As with any type of construction, an appropriate pest control program should be instituted and maintained.
The Purchaser’s sole and exclusive remedy for a valid claim against this warranty shall be for the replacement, without charge to the purchaser, of the Structall panels pursuant to the terms of the warranty. The obligation of Structall Building Systems, Inc. to replace the defective products shall not include the removal, dismantling, or reinstallation of any such products. Furthermore, the Purchaser agrees that no other remedy other than that prescribed above shall be available to the Purchaser or other aligned parties making a claim.
Prices Subject to Change Without Notice
STRUCTALL BUILDING SYSTEMS, INC. warrants to the Purchaser that Structall’s coated aluminum materials used in the roof pans will not split, chip, peel, flake or blister as a result of a defect in materials or workmanship for a period of 10 years from the date of purchase. In the event of a valid claim, Structall will provide replacement pan products.
This warranty does not cover damage caused by willful abuse, normal weathering, negligence or failure to provide normal maintenance and cleaning, exposure to industrial pollution, salt spray or chemical atmosphere, damage by physical abuse, abrasion, impact or other force, or an act of nature, such as fire, lightning, windstorms, hailstorms or causes beyond Structall Building Systems, Inc.’s control.
This warranty does not cover use of the product in applications beyond the design limits as spelled out in the Structall engineering publications. Installation not in strict compliance with the Structall installation instructions shall also void the warranty.
Under impact of weather, the coating on pan products will chalk and display some degree of color change during the normal aging process. As these conditions are unrelated to defects in the roof pans, they are not included in this warranty.
Structall Building Systems reserves the right to investigate any claims made under this warranty and to inspect the property in question. In the unlikely event that like products are no longer available, Structall Building Systems will provide substitute products of an equal grade.
The Purchaser’s sole and exclusive remedy for a valid claim against this warranty shall be for the replacement, without charge to the purchaser, of the Structall panels pursuant to the terms of the warranty. The obligation of Structall Building Systems, Inc. to replace the defective products shall not include labor or costs involved in the removal, dismantling, or reinstallation of any such products. Structall Building Systems responsibility for the cost of refinishing or furnishing replacement material shall be limited to one-hundred percent of the cost of replacement materials only at current market value for the affected area during the first year and shall decrease at a rate of fifteen percent per year for the next four years, five percent per year for the remaining five years. Furthermore, the Purchaser agrees that no other remedy other than that prescribed above shall be available to the Purchaser or other aligned parties making a claim.
Structall Building Systems makes no other warranties expressed or implied as to the products covered by this warranty. The remedies provided herein are exclusive, and are expressly in lieu of all other remedies, including any remedies for incidental or consequential damages.
Prices Subject to Change Without Notice
STRUCTALL BUILDING SYSTEMS, INC. warrants to the Purchaser that Structall’s oriented strand board clad panel products will not delaminate as a result of a defect in materials or workmanship for the life of the structure in which they are installed. In the event of a valid claim, Structall will provide replacement panels.
This warranty does not cover damage by willful abuse, normal weathering, exposure to industrial pollution, salt spray or chemical atmosphere, damage by physical abuse, abrasion, impact or other force, or an act of nature, such as fire, lightning, windstorms, hailstorms or causes beyond Structall Building Systems, Inc.’s control.
This warranty does not cover use of the product in applications beyond the design limits as spelled out in the Structall engineering publications. Installation not in strict compliance with the Structall installation instructions and procedures shall also void the warranty.
Oriented strand board is a wood composite product that is susceptible to damage from the elements. Panels should be stored in a dry environment and should not be exposed to rain and sun for extended periods of time. The oriented strand board will accept a reasonable amount of construction related exposure and may exhibit some surface flaking or scaling as a result. This condition is anticipated and does not reflect a defect of the panels. The panels are structural elements and are not designed to function as the primary interior or exterior surfaces. Structall recommends that in the final application, both surfaces be covered by an appropriate finish material.
This warranty does not cover infestation by insects, rodents or other pests. As with any type of construction, an appropriate pest control program should be instituted and maintained.
The Purchaser’s sole and exclusive remedy for a valid claim against this warranty shall be for the replacement, without charge to the purchaser, of the Structall panels pursuant to the terms of the warranty. The obligation of Structall Building Systems, Inc. to replace the defective products shall not include the removal, dismantling, or reinstallation of any such products. Furthermore, the Purchaser agrees that no other remedy other than that prescribed above shall be available to the Purchaser or other aligned parties making a claim. This warranty shall not be assignable by Purchaser.
Pay CapitalOne Trade Credit You have several convenient ways to pay - by statement, job or invoice. Pay online, by phone or by mail.
Burbank Road Oldsmar, FL 34677
Sales Desk: 877-314-2509
Information: 800-969-3706
Local: 813-855-2627
Fax: 813-814-0018
Toll Free: 855-431-2642
Local: 863-577-0600
Fax: 863-577-0659
Local: 225-673-8776
Toll Free: 800-880-4198
Local: 210-225-7997
Fax: 210-225-7197