VDE
COMPACT POWER RELAYS
30.0 1.181
JC
JC RELAYS FEATURES
19.0 .748 30.0 1.181
19.0 .748
30.4 1.197 32.4 1.276
PC board type Plug-in type
45.0 1.772
TM type
• High inrush current capability 1 Form A: 163 A inrush (TV-8) 2 Form A: 111 A inrush (TV-5) 19.0 .748 • High dielectric withstanding for transient protection: JC can withstand 10,000 V surge in µs 32.9 between coil and contact. 1.295 • Electrical life: 1 Form A: 105 ope. at 15 A 250 V AC resistive load 2 Form A: 105 ope. at 10 A 250 V AC resistive load • UL/CSA, VDE, TÜV, SEMKO also mm inch approved.
SPECIFICATIONS Contact
Characteristics
Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1 A) Contact material Contact force, min. Maximum switching power Rating Maximum switching voltage (resistive Max. switching current load) Min. switching capacity#1 Expected Mechanical life (min. Electrical 10 A 250 V AC operation) (resistive) 5A 250 V AC
1 Form A 2 Form A 30 mΩ (Cd free type: 100 mΩ) Silver alloy 30 g 3,750 VA 2,500 VA 250 V AC 250 V AC 15 A 10 A 100 mA, 5 V DC 5×106 5 10 — — 105
Maximum operating speed Initial insulation resistance*1 Between open contacts Initial Between contacts sets breakdown Between contacts and voltage*2 coil Operate time*3 (at nominal voltage) Release time(without diode)*3 (at nominal voltage) Temperature rise (at nominal voltage) Functional*4 Shock resistance Destructive*5
Coil Nominal operating power
900 mW
1,000 mW
#1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.
Vibration resistance
Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement of same location as “Initial breakdown voltage” section *2 Detection current: 10mA *3 Excluding contact bounce time *4 Half-wave pulse of sine wave: 11ms; detection time: 10µs *5 Half-wave pulse of sine wave: 6ms *6 Detection time: 10µs *7 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT
TYPICAL APPLICATIONS Automatic garage door openers Microwave ovens Dryers Vending machines Copiers Air conditioners Stereo equipment TV sets
20 cpm. Min. 100 MΩ at 500 V DC 2,000 V rms for 1 min. 2,000 Vrms for 1 min. 4,000 Vrms for 1 min. Max. 30 ms Max. 10 ms Max. 55°C 196 m/s2 {20 G} 980 m/s2 {100 G} 98 m/s2 {10 G}, 10 to 55 Hz at double amplitude of 1.6 mm 117.6 m/s2 {12 G}, 10 to 55 Hz at double amplitude of 2 mm –50°C to +60°C –58°F to +140°F
Functional*6 Destructive
Conditions for operation, Ambient transport and storage*7 temp. (Not freezing and condensHumidity ing at low temperature) Unit weight
5 to 85%R.H. Approx. 31 g 1.09 oz
ORDERING INFORMATION Ex. JC
1a
F
Contact Mounting classification arrangement 1a: 1 Form A 2a: 2 Form A
Nil: PC board terminal S: Plug-in terminal TM: Top mounting
TM
DC12V
F
Coil voltage
Environmental support
DC 5, 6, 12, 24, 48 V
F: RoHS Directive conforming type (AgSnO2 type) Nil: RoHS Directive non-conforming type (AgCdO type)
(Notes) 1. TV rated types available 1 Form A: TV-8; 2 Form A: TV-5. Notes ))2. Standard packing Carton: 50 pcs.; Case: 200 pcs. Notes ))3. UL/CSA, VDE, TÜV, and SEMKO certified products can also be supported. Notes )) Please consult us. All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
JC COIL DATA (at 20°C 68°F) Contact Nominal voltage. arrangement V DC
1 Form A
2 Form A
Pick-up voltage. V DC (max.)
Drop-out voltage. V DC (min.)
Coil resistance, Ω(±10%)
4.8 9.6 19.2 38.4 4.8 9.6 19.2 38.4
0.6 1.2 2.4 4.8 0.6 1.2 2.4 4.8
40 160 640 2,560 36 144 576 2,304
6 12 24 48 6 12 24 48
Nominal operating current, mA 150 75 37.5 18.8 166.6 83.3 41.6 20.8
Maximum allowable voltage, V DC (at 60°C) 6.6 13.2 26.4 52.8 6.6 13.2 26.4 52.8
Nominal operating power, W 0.9 0.9 0.9 0.9 1.0 1.0 1.0 1.0
DIMENSIONS
mm inch
PC board type JC1a
Schematic 6
Coil terminal Common terminal
30 1.181
1
5
N.O. terminal 4 .157 1.5 .059 6
14 .551 6.9 .272
1.5 .059
14 .551
3
0.4 .016 0.9 DIA. .035 DIA.
PC board pattern (Bottom view)
0.5 0.5 .020 .020
1
5
2
4
3 10 .394 19 .748
Relay outline
2-1.8 DIA. HOLES .071 DIA. HOLES
15.2 .598 30 1.181 7.6 .299
1 6
3.1 .122
2-1.2 DIA. HOLES .047 DIA. HOLES
3
2.54×4 19 .100×4 .748
5
2.54×6 .100×6 2.54×3 30 1.181 .100×3
PC board type JC2a
3.1 .122
Schematic
30 1.181
14 .551 6.9 .272
1.5 .059
14 .551 6
1
5
2
4
3 10 .394 19 .748
6
Common terminal
5
2
N.O. terminal
4
3
1
0.4 .016
4 .157 1.5 .059
Coil terminal
0.9 DIA. .035 DIA.
0.5 0.5 .020 .020
PC board pattern (Bottom view) Relay outline
15.2 .598 30 1.181 1 6
7.6 .299 3.1 .122
2-1.2 DIA. HOLES .047 DIA. HOLES
General tolerance: ±0.3 ±.012
2 5
3 4
2.54×4 19 .100×4 .748
2.54×6 4-1.8 DIA. HOLES .100×6 2.54×3 3.1 .071 DIA. HOLES .122 30 .100×3 1.181
Tolerance: ±0.1 ±.004
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
JC Top mount type
mm inch
1a
2a 45 1.772
45 1.772
2 .079
2 .079
30.5 1.201
30.5 1.201 1.4 DIA. .055
3.1 .122
2-3.2 DIA. 2-.126 DIA.
2.5 .098
0.5 .020 Accept Faston 187
3.1 .122
Hole spacing 37.6 1.480
3.6 .142
10.7 .421 26.7 1.051 30 1.181
37.6 1.480
2
5
MADE IN JAPAN
Schematic
1
3
26.7 1.051 30 1.181
4
10.7 .421
2.5 4.75 .098 .187
8.35 .329
37.6 1.480
2-3.2 DIA. 2-.126 DIA.
6
12 .472
1 19 .748
19 .748
5 6
1
37.6 1.480
Schematic
3 12 .472
2.5 4.75 .098 .187
Hole spacing
6
0.5 .020 Accept Faston 187
9 .354
2
2.5 .098
8.35 .329 0.9 .035
5
3.6 .142
2.4 .094
8.35 .329
MADE IN JAPAN
9 .354
3
8.35 .329 0.9 .035
4
2.4 .094
1.4 DIA. .055
N.O. terminal 3
4
Common terminal 2
5
Coil terminal
1
6
Plug-in type 1a
2a
30 1.181
30 1.181 1.4 DIA. .055
2.5 4.75 .098 .187
3.1 .122
Schematic
10.7 .421
2
5
3
26.7 1.051
30 1.181
2.5 .098
19 .748 9 .354
2
3
4
MADE IN JAPAN
26.7 1.051
0.5 .020 Accept Faston 187
8.35 .329
5
3.1 .122 10.7 .421
2.5 .098
19 .748 9 .354
2.4 .094 0.9 .035
8.35 .329
3
8.35 .329
4
2.4 .094 0.9 .035
1.4 DIA. .055 8.35 .329 0.5 .020 Accept Faston 187
Schematic 30 1.181
MADE IN JAPAN
5 1
6
1 12 .472
6
6
1
2.5 4.75 .098 .187
N.O. terminal 3
4
Common terminal 2
5
Coil terminal
12 .472
1
6
General tolerance: ±0.3 ±.012
REFERENCE DATA JC1a type 1. Maximum value for switching capacity
2. Life curve
3.-(1) Coil temperature rise Point measured: Inside the coil Ambient temperature: 26°C 79°F
AC resistive load
DC resistive load 1 DC inductive load (L/R = 7 ms)
250 V AC resistive load 30 V DC resistive load
100 250 V AC inductive load (cosϕ = 0.4) 10
0.1
30 V DC inductive load (L/R = 7 ms)
Temperature rise, °C
Contact current, A
AC inductive load (cosϕ = 0.4)
Life, × 104
80
15 10
70
nt
rre
60
5A
cu
1
nt
rre
0A
cu
1
50
nt
rre
5A
40
cu
nt
rre
30
No
cu
20 1
10
100 400 Contact voltage, V
0
5
10
15
Contact current, A
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
0
80
90 100 110 120 130 140 Coil applied voltage, %V
JC 3.-(3) Coil temperature rise
Point measured: Inside the coil Ambient temperature: 40°C 104°F
Point measured: Inside the coil Ambient temperature: 60°C 140°F
70 60 50
t
en
urr
c 5A
1
A 10
nt rre cu
40
t
en
urr
c 5A
30 20
No
0
80
80 70 60 50
1
cu
c 5A
nt
No
0
80
t
en
urr
20
nt
rre
A 10
40
t
90 100 110 120 130 140
t
en
urr
c 5A
30
en
rr cu
4. Operate / release time
Operate and release time, ms
80
Temperature rise, °C
Temperature rise, °C
3.-(2) Coil temperature rise
e urr
c
90 100 110 120 130 140
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 4 3 2 1 0
Operate time Max. Min. Release time 80
100
Coil applied voltage, %V
Coil applied voltage, %V
Coil applied voltage, %V
Max. Min. 120
JC2a type 1. Maximum value for switching capacity
2. Life curve
3.-(1) Coil temperature rise Point measured: Inside the coil Ambient temperature: 26°C 79°F
1 DC inductive load (L/R = 7 ms)
100 Life, × 104
Contact current, A
AC resistive AC load inductive load DC resistive load (cosϕ = 0.4)
250 V AC resistive load 30 V DC resistive load 10
0.1
Temperature rise, °C
80 10
250 V AC inductive load (cosϕ = 0.4)
0
100 250 400 Contact voltage, V
2
4
6
8
10 12A
80 70 60
nt
nt
rre
rre
cu No t n rre
cu
40 30
cu
r
5A
20 0
t ren
3A
80
cu
90 100 110 120 130 140 Coil applied voltage, %V
Temperature rise, °C
Point measured: Inside the coil Ambient temperature: 60°C 140°F
Temperature rise, °C
3.-(3) Coil temperature rise
Point measured: Inside the coil Ambient temperature: 40°C 104°F
8A
1
8A
nt
0A
8A
cu
1
0
rr cu
c
nt 3 A
No t n rre cu
rre
5A
80
t
en
e urr
30 20
nt
t
en
urr
c No
rre
3A
cu
80
cu
90 100 110 120 130 140
4. Operate / release time
rre
60
40
cu
Coil applied voltage, %V
70
nt
rr cu
40
0
80
50
t
rre
5A
en
50
Contact current, A
3.-(2) Coil temperature rise
50
60
cu
20
90 100 110 120 130 140 Coil applied voltage, %V
Operate and release time, ms
10
nt
rre
0A
30
30 V DC inductive load (L/R = 7 ms) 0.01 1
nt
70
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 3 2 1 0
Operate time Max. Min. Release time 80
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Max. Min.
100 120 Coil applied voltage, %V
JC ACCESSORIES
JC1-SS
JC2-SS
JC1-PS
JC2-SS
JC2-PS
mm inch Tolerance: ±0.5 ±.020
9±0.2 .354±.008
26 1.024 9±0.2 .354±.008
Faston187
0.25 .010
7.6±0.2 .299±.008
0.25 .010
7.6±0.2 .299±.008 35 1.378
16±0.2 .630±.008
36 1.417
16±0.2 .630±.008
JC2-PS
2.0 .079 4.75 .187 7.5 .295 18.7 .736
12±0.2 .472±.008
22 .866
22.3 .878
16.2 .638
12±0.2 .472±.008
5 .197
JC1-PS 4-2.4 DIA. 4-.094 DIA.
JC2-PS
9 .354
9 .354 7.6 .299
7.6 .299 6-2.4 DIA. 6-.094 DIA.
32.3 1.272
15.45 .608
15.45 .608
13.1 .516
Panel cutout
13.1 .516
PC board Pattern
Tolerance: ±0.1 ±.004
Tolerance: ±0.1 ±.004
(Note) Outward dimensions and chassis cutout dimensions for JC1-SS and JC1-PS are same as those of JC2-SS and JC2-PS respectively. UL/CSA approved type is standard.
For Cautions for Use, see Relay Technical Information
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.