Econolift
™
Product Code
062051 rolling Door Opener
Specifications: Motor Specifications Power Supply
230-240VAC
Transformer Voltage Prim 230-240VAC Sec: 24VAC Standby Power Consumption
2.2W
Motor Type
Permanent magnet
Motor Voltage
24 VDC
Motor Power
100W
Motor Output Speed
70rpm
Travel Speed (mm/sec) Open/Close
160 / 160
Soft Start/Soft Stop
No
Manual Release
Integral motor/ clutch type pull/pull
Lockable Engage Disengage No Courtesy Light
No
Light Source
N/A
Door & Mounting Specifications
Description: Available only in retail outlets, the DIY oriented Econolift™ is suitable for doors up to 8m2 in size. Econolift Rolling Door Opener
PART NO. 062051
Contains 062266
1 button transmitter
Maximum Door Travel Limit in Barrel Turns
31/4 turns
Maximum Lifting Force
300N
Maximum Door Size (Area)
8m2
Maximum Door Weight
100kg
Recommended Lateral Space Requirements
95mm
Minimum Lateral Space Requirements
40mm
Opener Weight
6.2kg
Weight Bar
2kg metal filled plastic bottle
Transmitter Specifications Code Format Fixed Code 3 billion codes Transmission Frequency 433.92MHz Transmitters Shipped with Unit
1
Transmitter (1)Type specification
B&D 1 button (062266)
Transmitter (2)Type specification
N/A
Receiver Storage Capacity 6 + 1 dip switch (No. of Transmitters) + 1 keypad See overleaf for continuation of Specifications...
Econolift
™
Product Code
062051 rolling Door Opener
Optional Accessories & Auxillary Inputs Safety Infra-Red Beam
Yes
Wireless Keypad Transmitter
Yes
Other Features Obstruction Force Margin
Adjustable
Control Panel Buttons Disable
Yes
Overload Indicator
Yes
Service Indicator
Yes
Warranty Indicator
Yes
Mains Failure Indicator
Yes
Obstruction Indicator
Yes
Door Travel Limits Setting
Motor driven
Auto Close
N/A
Warranty Warranty (Years)
Installation requirements/ instructions: The door must be well balanced and be in a reasonable operating condition. You should be able to lift the door smoothly and with little resistance. It should stay open around 900mm to 1200mm above the floor. The door should not stick or bind in the guide tracks. The ideal operational effort in raising or lowering the door should not exceed a force of 10kg (22 lbs.). Make sure that all door locks, ropes, chains etc. are either released, or disabled and remove unnecessary accessories. Fig. 1 shows the minimum and recommended sideroom that is required to mount the opener. The distance between the edge of the door curtain and the inside of the bracket must be at least 40mm. However, for easier access it is recommended that at least 95mm is allowed.
1 year parts only
Features: • Suitable for doors up to 8m2. • Only needs 40mm sideroom (curtain to bracket) for installation. • Compatible with PG-3 Programmer. • Optional keyed lockout prevents manual disengagement in exposed applications. • Disable function for control panel as standard. • 433MHz radio frequency for better reception and less interference.
Minimum Sideroom
Recommended Sideroom
Method of operation: Activate the operator by either the door control button, outside key switch or keyless entry system, the remote control transmitter or manually open the door, by pulling the release handle down.
Door type: Standard residential rolling garage doors.
RP 07/06
Econolift
™
Product Code
062051 rolling Door Opener
Trouble shooting & maintenance: SYMPTOM
POSSIBLE CAUSE
Door will not operate
Mains power not switched on.
Switch on mains power.
Door is obstructed.
Remove obstruction.
Door is locked or motor jammed.
Unlock door or remove jam.
Door tracks/hardware damaged.
Door requires service/repair by qualified technician.
Adverse weather conditions (wind or cold) causing door to stiffen and become tight in the tracks.
Increase force margin setting. Or re-calculate force margin.
Possible obstruction in the doorway.
Remove obstruction.
Transmitter code not stored in memory.
Code transmitter into openers memory.
Flat Battery.
Replace battery.
Door will not open or close fully
Door limits position need to be reset.
Reset limits position.
Door is overshooting or not reaching limits
Datum position not set correctly.
Reset datum position.
Cannot set limits
Datum position not set correctly.
Set datum position.
Door not working with IR Beam installed
Safety infra-red beam or wiring faulty.
Repair safety infra-red beam or replace wiring.
Door starts to close but automatically reverses to open position
Door operates from drive unit (OPERATE) button but not from transmitter *(See note)
Safety infra-red beam not aligned correctly. Safety infra-red beam is obstructed. Door obstructed when closing.
REMEDY
Re-align optics. Remove obstruction from the path of safety infra-red beam. Remove obstruction.
*Please Note: Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones, wireless stereo headphones and baby monitors. It is possible that these devices could cause a degree of interference such as to greatly reduce the range of the transmitter. In such an instance please contact your B&D dealer for an alternative frequency replacement kit. As this is not a warrantable situation but an environmental issue charges may apply for the changeover.
Spare parts list: ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23a 23b 24 25 26 27 28 29 59693
62076 62082
62065 62079 62078 62081
62080 62071 62073
PART NO.
DESCRIPTION Drive Chassis Sub-Assy Internal Gear Axle Hex Serration Head Screw M6x20 Internal Gear Clamp Washer Retaining Ring STW 45 Clamping Saddle Bracket Clutch Geared Motor Assy 12-01 WS Transformer TDB-72-01 Kit (72VA) Ratchet Timing Assy Power Cord A.S 1.5m 2P1R Felt 21 x 29 Terminal Block 500/02DS 2 POS Cap Polyfilm 0.1UF K X2 275 VAC Hex Serration Head Screw M8x16 Taptite Screw 'P' M4x10 Pan Head Screw W/Washer M4x8 Taptite Screw 'P' Black ZNC M3x14 Internal Tooth Lock Washer I.D 3 Cable Tie 4" GT-100M String Handle Assy Control Board CB-17 Chassis Enclosure Assy Warning Info Label_SM Control Cover Assy Industrial Saddle U-Bolt M8 Hex Serration Flange Nut M8 (Black) Flat Washer 8.4x18x1.6 Weight Bar
Econolift ™
Product Code
062051
rolling Door Opener
RP 07/06