2
ComFlor 80 in construction at 21 Queen Street, December 2008
ComFlor 80 in construction at 80 Queen Street, December 2008
3
Unpropped - Quick Reference Load Span Table Notes Double Span in Construction - Simple Span in Service
The purpose of these tables is for rapid conceptual design only. A full design analysis using the ComFlor software (and other ‘whole system’ software) is required to verify all design parameters are met. Double Span in Construction Sheets are continuous over permanent supports
End span (use double span data)
Internal span
End span (use double span data)
Spans shown in this table are ‘centre to centre’ of 150mm wide (top flange) beams as is typical in unpropped continuous sheet construction. Wider beams will result in longer spans. To this end these tables can be considered conservative in most applications. Spans listed are in 50mm increments with intermediate values at 25mm. Generally for double span construction, strength of the sheet over the support will govern the design. Even if the ComFlor sheets are continuous over a permanent support in construction, the slab will act as a simple span in service unless full continuity reinforcement is placed over the permanent supports. 25MPa (cylinder strength) concrete used.
95% strength in construction
The green zone is the ‘safe’ zone within which the ComFlor is not unduly taxed structurally during construction.
98% strength in construction
The orange zone can be considered the ‘working’ zone where most efficient designs will occur. Concrete pour sequencing is important within the orange zone to minimise ponding and result in flatter concrete surface.
100% strength in construction
The red zone should never be used.
Permanent support
Sheets are continuous over permanent supports
Double (or end) span
Double (or end) span
General Apart from the 0.75mm data, these tables have been derived from version 8.3 of the ComFlor design software. The 0.75mm data has been derived manually based as closely as possible to those parameters used in ComFlor. Outputs from future versions of ComFlor may differ slightly from those in these tables, therefore is important to always verify a design using the latest software.
4
ComFlor
The construction deflection column to the right of the tables indicates the resultant deflection at the end of each of the colour bands. Ultimately it is the ’clear span’ that dictates the design. As the top flange width increases with larger beam selection, the possible beam centres increase. Specific design using the ComFlor software is required.
5mm, 15mm, 22mm indicate the underside deflection to expect (inclusive of concrete ponding midspan) during construction. The line to the right thus 5mm indicates the span applicable to that deflection figure. As a guide: 5mm – Practically flat appearance to the underside 15mm – 15mm underside deflection has generally proven to be a good compromise between visual appeal and functional construction spans. 22mm – A good ‘working’ maximum where underside appearance is not important, but maximum construction spans are desired. 25mm – Generally the absolute maximum underside deflection advised unless the visual appearance is of no relevance.
Loadings Represented in the tables SLL (Q)
SDL (G)
kPa
kPa
15.0
0.5
E - minimum value for cold storage
10.0
0.5
E - minimum value for mobile stacking, mechanically operated heavy shelving (wheels on rails, eg compactus)
7.5
0.5
C5 - Stages in public assembly areas (no allowance for dynamic activities has been allowed for)
5.0
0.5
E - file rooms, office storage space, vaults and strongrooms
3.0
0.8
B - offices for general use
2.5
0.1
F - parking, garages, driveways and ramps restricted to cars, light vans, etc not exceeding 2500kg gross mass
1.5
0.8
A1 - General areas, private kitchens and laundries in self contained dwellings.
Normal Stage Strength criteria limited to 95% utilisation. Total Deflection is limited to the smaller of span/250 or 30mm. Serviceability criteria limited to 99% utilisation (of 5Hz).
Category Reference from AS/NZS 1170.1:2002, table 3.1
Note - Point loads have not been considered for these quick reference tables. Please use the ComFlor software and/or discuss your needs with a ComFlor representative.
The composite (normal stage or ‘in service’) spans are designed to a 5Hz vibration limit. Studies of existing slabs have shown that this parameter results in a solid feeling slab that does not generally produce unsettling vibration underfoot if the support structure is inherently rigid (ie a concrete block wall). Please note that the slab alone does not necessarily dictate the overall slab ‘system’ vibration characteristics. If the support structure has the potential to be flexible (ie structural steel), the whole floor system should be considered for vibration. Spans can be increased markedly if the vibration criterion is relaxed or not critical to the end use of the slab. Load/span combinations in these tables achieve a guaranteed 30 minute fire resistance rating (FRR). Greater than 30 minutes is often possible, dependant on the actual imposed load (tables give possible load based on 30 minutes FRR) - use the ComFlor software to determine if the desired FRR can be achieved without additional reinforcing. Use the ‘Simple’ setting first to determine if mesh alone will satisfy the fire condition. ComFlor allows for different mesh sizes to be considered in the ‘Simple’ method - or, using the ‘Fire Design’ method different bar sizes (10 to 32mm) can be placed in the ComFlor troughs in order to improve fire performance.
omFlor 80 Single Span Sheets in Construction - Simple Span Composite Slab - 30 minute fire rating 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 The load capacity for any given 10.0 7.5 load/span configuration is shown as:
5.0
3.0
10.0 7.5 The fire rating will naturally increase at any given 10.5 7.5span if the actual design load is less than that shown on the tables. 12.0 10.0 7.5
0 13.0
10.0
0 15.0 15.0
1.5
2.5
5.0
3.0 5.0
1.5
2.5
3.0
1.5
5.0 7.5
10.0
2.5
3.0
7.5 10.0
15.0
1.5
5.0
5.0
2.5
3.0/1.5
7.5 10.0
2.5
3.0/1.5 5.0 7.5
2.5 3.0
1.5
5.0/3.0/1.5
Composite floor decking www.comflor.co.nz 2.5 2.5
5
Quick Reference Load Span Table UnPropped ComFlor 60 Double Span Sheets in Construction Simple Span Composite Slab - 30 minute fire rating Quick Reference Load Span table - UnPropped ComFlor 60 Double Span Sheets in Construction - Simple Span Composite Slab - 30 minute fire rating
1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60
125
15.0
5mm
130
15.0
140
10.0 15.0 15.0
5mm
>15.0 >15.0
5mm
>15.0 >15.0
5mm >15.0 >15.0 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 15.0
5mm
130
15.0 15.0
150 160
10.0 11.0 15.0
21.0 20.5 24.0 23.0
26.5 25.5
5mm 29.0 28.0 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 15.0
125
15.0
150 160 180
15.0 15.0 18.0
5mm
220
9.5
9.0
11.0 11
15mm 14.0 13.5
15mm 17.0
8.0
23.0 22.0
5mm
Construction Deflection 13mm
14mm
15mm
13mm
14mm
15mm
13mm
14mm
14mm
13mm
14mm
14mm
13mm
14mm
14mm
13mm
13mm
14mm
11mm
12mm
13mm
10mm
11mm
11mm
8mm
9mm
10mm
7mm 8mm 9mm Construction Deflection 14mm
15mm
15mm
14mm
15mm
16mm
14mm
15mm
15mm
14mm
15mm
15mm
13mm
14mm
15mm
12mm
13mm
14mm
11mm
12mm
13mm
10mm
11mm
11mm
9mm
10mm
10mm
9mm 9mm 10mm Construction Deflection 16mm
16mm
17mm
16mm
17mm
17mm
16mm
16mm
17mm
17mm
18mm
17mm
17mm
18mm
18mm
17mm
18mm
18mm
15mm
17mm
17mm
14mm
15mm
16mm
13mm
14mm
15mm
25.0 24.0 5mm 12mm 13mm 14mm 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 Construction Deflection
125
15.0
130
5mm 15.0 15.0
150
10.0
5mm
15.0
220
15mm
5mm
15mm
9.0
6.5 7.0
9.0
13.0 13.0 16.0 15.0
19.5
18mm
19mm
20mm
19mm
20mm
20mm
19mm
8.0
10.5 10.0
15mm
15mm
5mm
240
7.0 8.0
10.0
15mm
5mm
6.5 7.5
15mm
15mm 15.0
15mm
15mm
15.0
5mm
200
7.5 10.0
5mm
5mm
160 180
10.0
5mm
140
17.5
21.0 20.5
20mm
20mm
19mm
20mm
21mm
19mm
20mm
21mm
20mm
20mm
21mm
20mm
21mm
21mm
18mm
20mm
20mm
17mm
18mm
19mm
5mm 15mm 23.0 22.0 16mm 17mm 18mm 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 Construction Deflection
125
15.0
130
5mm 15.0
150
5mm
160
10.0 15.0 15.0
220
5mm
240
5mm
18.0 18.0 19.5 19.0
8.5 10.0
12.5 12.0 15.0 15.0
15mm 15mm
10.0
15mm
15mm
6.5 7.5
15mm 15.0
5.5 7.5
15mm
15mm
5mm
15mm
15mm
5mm
5mm
200
7.5 10.0
5mm
180
10.0
5mm
15.0
140
6
8.5
7.0
7.0
21.0 20.0
5mm
240
15mm
15mm
5mm
200
260
10.0
5mm
7.5
15mm
5mm 15.0
5mm
7.0
15mm 10.0
5mm
140
1.20
10.0
5mm 15.0
130
260
9.0
10.5
16.5 16.0
5mm 5mm 5mm
9.0
7.5 8.0
12.5 12.5
5mm
220
1.10
8.0
5mm
5mm
180
260
7.5 10.0
5mm 15.0
200
1.00
10.0
5mm
140
260
>10.0 >10.0
>15.0 >15.0
125
240
>10.0 >10.0 15.0
5mm
220
5.0
>10.0 >10.0
5mm
200
0.90
7.5
5.0
10.0 >7.5
5mm
180
260
5mm
5mm
160
240
7.5
5mm 15.0
150
0.75
10.0
9.5
8.5
7.0
6.5
5.5
22mm
23mm
24mm
22mm
23mm
24mm
22mm
23mm
23mm
22mm
23mm
24mm
22mm
23mm
24mm
22mm
23mm
23mm
22mm
23mm
23mm
22mm
23mm
23mm
21mm
22mm
23mm
5mm 15mm 21.0 21.0 20mm 21mm 21mm 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 Construction Deflection
ComFlor
Quick Reference Load Span Table UnPropped ComFlor 80 Double Span Sheets in Construction Simple Span in Service - 30 minute fire rating
ComFlor Quick Reference Load Span table - UnPropped
ComFlor 80 Double Span
Sheets in Construction - Simple Span in Service - 30 minute fire rating
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
0.75
145 150 160 170 180 190 200 220 240 260
15.0
5mm 15.0
10.0
5mm 15.0 5mm
10.0
5mm 15.0
5mm 5mm >15.0 >15.0
7.5
>15.0 >15.0
5mm 5mm
15.0 >15.0
>15.0
Construction Deflection 11mm 11mm 10mm 10mm 10mm 10mm 9mm 8mm 7mm 6mm
>10.0 >10.0 >10.0 >10.0 >10.0 >10.0 >10.0
15.0
5mm
5mm
7.5 5.0
>15.0
>15.0
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
0.90
145 150 160 170 180 190 200 220 240 260
15.0
5mm 5mm
15.0 15.0
10.0 10.0
15.0 5mm 5mm
10.0 11.5
15.0
13.0 15.0
5mm
22.0
5mm 21.5
5mm 20.0
8.5
5mm
5mm 16.5 18.0
8.0 8.5
8.0
11.0
12.5
14.5
16.0
17.5
19.5
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
1.00
145 150 160 170 180 190 200 220 240 260
15.0
5mm 15.0
10.0
7.5
5mm 15.0
10.0
5mm 15.0 5mm
5mm 15.0
11.5
5mm
15.0
13.0
5mm
14.5
5mm
16.5
5mm
18.5
5mm
20.5
15mm 15mm 10.5 10.0
10.0
7.0
6.5
8.0 8.5
9.0
11.5
13.0
14.5
16.0
18.0
19.5
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
1.10
145 150 160 170 180 190 200 220 240 260
15.0
5mm 15.0
10.0
5mm 15.0
15mm 15mm
10.0
5mm 15.0 5mm
10.0
5mm
5mm
15.0
15mm
5mm
15.0
5mm
15.5
5mm
17.0
5mm
18.5
15mm 15.0
12.0 13.5
8.5 10.0 10.5 11.5
15mm
6.5 7.0
7.5
15mm 15mm
15.0
7.5
9.5 10.5
6.0
8.5
13.0
16.5
18.0
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
1.20
145 150 160 170 180 190 200 220 240 260
15.0
5mm 5mm
15.0 15.0
10.0 10.0
5mm 15.0 5mm 5mm 5mm
10.0 15mm 15.0
5mm
15.0 15mm
5mm
15mm 15mm
17.0
7.5 8.0
10.0
9.0 10.0
11.5
15mm
12.5 15.0 15.5 15.0
7.5
15mm
15mm 15mm
15.0
5mm 5mm
15mm 15mm
14.0
22mm 22mm 7.5
5.0 6.0
3.0 5.0
1.5
2.5
8.5
10.0
11.0 12.0
14.0
16.5
15mm 15mm 14mm 13mm 13mm 12mm 12mm 10mm 10mm 9mm
17mm 18mm 18mm 17mm 16mm 15mm 14mm 13mm 12mm 11mm
17mm 18mm 18mm 17mm 16mm 15mm 15mm 14mm 13mm 11mm
Construction Deflection 18mm 18mm 18mm 18mm 19mm 18mm 17mm 15mm 14mm 13mm
9.5
15mm 15mm 14mm 13mm 12mm 12mm 11mm 10mm 10mm 9mm
Construction Deflection 15mm 17mm 17mm 16mm 15mm 14mm 13mm 12mm 11mm 10mm
7.5
12mm 12mm 12mm 11mm 11mm 11mm 11mm 9mm 8mm 7mm
Construction Deflection 14mm 14mm 13mm 12mm 12mm 11mm 11mm 10mm 9mm 5mm
10.0
11mm 11mm 11mm 11mm 11mm 10mm 10mm 9mm 8mm 7mm
19mm 19mm 19mm 20mm 20mm 19mm 18mm 16mm 15mm 14mm
20mm 20mm 20mm 20mm 21mm 19mm 19mm 17mm 16mm 14mm
Construction Deflection 25mm 24mm 22mm 22mm 20mm 21mm 21mm 21mm 19mm 17mm
2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.40
Composite floor decking www.comflor.co.nz
26mm 26mm 24mm 23mm 22mm 21mm 23mm 22mm 20mm 18mm
28mm 27mm 25mm 24mm 23mm 21mm 24mm 22mm 21mm 19mm
Construction Deflection
7
Quick Reference Load Span Table Notes Single Span in Construction - Simple Span in Service
The purpose of these tables is for rapid conceptual design only. A full design analysis using the ComFlor software (and other ‘whole system’ software) is required to verify all design parameters are met.
Spans listed are in 100mm increments with intermediate values at 50mm. For unpropped single span design, underside deflection during the concrete pour will (generally) govern the effective span. For propped single span design, the resultant vibration and deflection characteristics of the composite slab will (generally) govern the design.
Single span in construction
‘stand alone’ span between two permanent supports
Single span unpropped (can be propped for longer spans)
‘stand alone’ span between two permanent supports
ComFlor sheet
Even if the ComFlor sheets are continuous over a permanent support in construction, the slab will act as a simple span in service unless full continuity reinforcement is placed over the permanent supports. 25MPa (cylinder strength) concrete used.
Permanent support
Sheets DO NOT continue over permanent supports
Construction Stage The colour zones on the table represent the ponded (soffit) deflection to expect during construction. ComFlor sheet
Temporary line of propping Single Span propped
Single Span unpropped
General Apart from the 0.75mm data, these tables have been derived from version 8.3 of the ComFlor design software. The 0.75mm data has been derived manually based as closely as possible to those parameters used in ComFlor. Outputs from future versions of ComFlor may differ slightly from those in these tables, therefore is important to always verify a design using the latest software.
8
ComFlor
Spans shown in this table are ‘clear span’ plus 100mm to reflect the typical application of the ComFlor sheet in a single span slab - 50mm seating onto the support structure.
15mm deflection
16 to 22mm deflection
over 23mm deflection
5mm, 15mm, 22mm indicate the underside deflection to expect (inclusive of concrete ponding midspan) during construction. The line to the right thus 5mm indicates the span applicable to that deflection figure. As a guide: 5mm – Practically flat appearance to the underside. 15mm – 15mm underside deflection has generally proven to be a good compromise between visual appeal and functional construction spans. 22mm – A good ‘working’ maximum where underside appearance is not important, but maximum construction spans are desired. 25mm – Generally the absolute maximum underside deflection advised unless the visual appearance is of no relevance.
Normal Stage Strength criteria limited to 95% utilisation Total Deflection is limited to the smaller of span/250 or 30mm Serviceability criteria limited to 99% utilisation (of 5Hz)
Propping Please note, when propping is used, the self weight of the slab is applied as a dead load once props are removed and can result in lower load capacity than that of an unpropped slab of the same span. This is because (the self weight of) an unpropped slab ‘loads up’ as it is poured, whereas when propped the self weight is held by the propping initially.
The composite (normal stage or ‘in service’) spans are designed to a 5Hz vibration limit. Studies of existing slabs have shown that this parameter results in a solid feeling slab that does not generally produce unsettling vibration underfoot if the support structure is inherently rigid (ie a concrete block wall). Please note that the slab alone does not necessarily dictate the overall slab ‘system’ vibration characteristics. If the support structure has the potential to be flexible (ie structural steel), the whole floor system should be considered for vibration. Spans can be increased markedly if the vibration criterion is relaxed or not critical to the end use of the slab.
The propping break lines (from 0 to 1, 2 or 3 rows required) occur at 95 % strength utilisation of the ComFlor sheet in construction.
The heavy lines indicate those points at which one or more prop lines are required.
The propping line used must be checked to ensure it has the required capacity to support the construction loads. ComFlor has the capacity to span far enough to impart up to 1500kg per linear metre onto the propping line.
Spans can be further increased by the addition of bottom reinforcing. Up to 600mm (varies) additional span can be achieved to that shown. Bottom reinforcing can be added also to increase the load carrying capacity of any given span/slab thickness combination. Use the ComFlor design software to verify.
A top bearer width of 100mm is used for the temporary propping system. Construction spans can be increased if wider bearers are used.
Load/span combinations in these tables achieve a guaranteed 30 minute fire resistance rating (FRR). Greater than 30 minutes is often possible, dependant on the actual imposed load (tables give possible load based on 30 minutes FRR) - use the ComFlor software to determine if the desired FRR can be achieved without additional reinforcing. Use the ‘Simple’ setting first to determine if mesh alone will satisfy the fire condition. ComFlor allows for different mesh sizes to be considered in the ‘Simple’ method - or, using the ‘Fire Design’ method different bar sizes (10 to 32mm) can be placed in the ComFlor troughs in order to improve fire performance.
Loadings Represented in the tables SLL (Q)
SDL (G)
kPa
kPa
15.0
0.5
E - minimum value for cold storage
10.0
0.5
E - minimum value for mobile stacking, mechanically operated heavy shelving (wheels on rails, eg compactus)
Category Reference from AS/NZS 1170.1:2002, table 3.1
omFlor 80 Single Span Sheets in Construction - Simple Span Composite Slab - 30 minute fire rating
- Stages in public assembly areas (no allowance for dynamic 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.07.5 5.1 5.2 0.5 5.3 5.4C5 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 activities has been allowed for) The load capacity for any given 10.0 7.5 load/span configuration is shown as:
5.0
3.0
10.0 7.5 The fire rating will naturally increase at any given span if the actual 10.5 7.5 design load is less than that shown on the tables. 12.0 10.0 7.5
0 13.0
5.0 5.0
10.0
7.5
0 15.0
10.0
7.5 10.0
15.0
7.5
15.0
10.0 15.0
1.5
2.5 5.0
3.0
1.5 3.0 3.0 2.5
0.5 2.5 0.8
E - file rooms, office storage space, vaults and strongrooms
B - offices for general use 2.5 F - parking, garages, driveways and ramps restricted to cars, 0.1 light vans, 5.0 3.0 1.5 2.5 etc not exceeding 2500kg gross mass A1 General 5.0 3.0/1.5 2.5 areas, private kitchens and laundries in self 1.5 0.8 contained dwellings. 5.0 3.0/1.5 2.5 Note - Point loads have not5.0 been considered for these quick 3.0 1.5 2.5reference tables. Please use the ComFlor 7.5 software and/or discuss5.0/3.0/1.5 your needs with a ComFlor representative. 2.5
1.5
10.0 15.0
7.5 10.0
5.0/3.0/1.5 7.5
2.5 5.0/3.0
1.5
2.5
3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Composite 5.9 6.0 6.1 6.3 6.4 6.5 6.6 floor6.2 decking 10.5 11.5
9.0 9.5
7.5
5.0 7.5
3.0 5.0
3.0
www.comflor.co.nz
2.5
1.5 1.5
2.5
9
Quick Reference Load Span Table ComFlor 60 Single Span Sheets in Construction Simple Span Composite Slab - 30 minute fire rating
ComFlor Quick Reference Load Span table - ComFlor
60 Single Span
Sheets in Construction - Simple Span Composite Slab - 30 minute ďŹ re rating
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
125
5mm 15.0
130
5mm
140
5mm
150
0.75
15.0
5mm
7.5 7.5
15.0 15.0
5mm 15.0
140 150
0.90
15.0
5mm
160 180
5mm
200
5mm
220
26.5
5mm
240 260
28.0 29.5
5mm 5mm
2.5
3.0/1.5
5.0
3.0/1.5 5.0
5.0
3.0 3.0
7.5
2.5 2.5
3.0/1.5
1.5
2.5 2.5
3.0/1.5
7.5
5.0
3.0
7.5
10.0 15.0
2.5 3.0
5.0
10.0
3.0
7.5
15.0
2.5
1.5
5.0
10.0
2.5
5.0
10.0
3.0
7.5
15.0
1.5
3.0
7.5
15.0
2.5
1.5
5.0
10.0
25.0 26.5
2.5 1.5
5.0 7.5
23.0
1.5
5.0
7.5
17.5 20.0
2.5
5.0
3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
15.0 14.0
22.0 24.5
2.5 3.0/1.5
7.5
12.5
17.5
5mm
2.5 1.5
3.0
7.5
10.5
15.5
5mm
1.5
5.0
10.0
9.5
13.5
3.0
7.5
8.5
11.5
2.5
1.5
5.0
10.0
10.5 15.0
2.5
3.0 5.0
10.0
15.0
5mm
1.5
7.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 130
1.5
7.5
15.0
125
2.5
5.0
10.0
>15.0
1.5 3.0
5.0
10.0
>15.0
2.5 3.0
7.5
15.0
>15.0
5mm 5mm
>7.5
>10.0
>15.0
3.0 5.0
7.5
10.0
>15.0
5mm
220
10.0
>15.0 15.0
5mm
200
>7.5
15.0
5mm
180
>10.0
5.0
7.5
>10.0
5mm
160
240 260
10.0 15.0
1.5
2.5
5.0
10.0
1.5
3.0
2.5
5.0
7.5
1.5
3.0
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 125
11.0
15.0
5mm
140
180 200
25.0
5mm
220
26.0
5mm
240 260
28.0 29.5
5mm 5mm
3.0
7.5
3.0
7.5
2.5 3.0
5.0
10.0
7.5
15.0
2.5
1.5
3.0
7.5
15.0
1.5
5.0
10.0
2.5 3.0
7.5
15.0
1.5
5.0
10.0
26.0
2.5
1.5
5.0
10.0 15.0
2.5
1.5
5.0
10.0
24.0
2.5 3.0
7.5
22.5
1.5
3.0 5.0
12.5
17.5 20.5
2.5
1.5
5.0 7.5
15.0 14.5
22.0
5mm
3.0
7.5
11.0
18.0
5mm
5.0
10.0
16.0 15.0
5mm
160
9.0
12.0 15.0 14.5
5mm
150
1.00
15.0
5mm
130
10.0
2.5
1.5 3.0
5.0 7.5
1.5
2.5
5.0
3.0
1.5
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 125
5mm
130
5mm
180 200
26.0
5mm
240 260
7.5
30.0
1.5
2.5 3.0
1.5
5.0
10.0
2.5 3.0
1.5 3.0
7.5
3.0
7.5
15.0
2.5
1.5
5.0
10.0
15.0
2.5
5.0
10.0
1.5
5.0
10.0
26.0
1.5
5.0 7.5
15.0
2.5 3.0
7.5 10.0
24.0
28.0
5mm 5mm
2.5
5.0
12.5
21.0 22.0
1.5 3.0
7.5
18.0
24.0
3.0 5.0
7.5
14.5
22.0
5mm
220
10.0
18.0
5mm
5.0
11.0
16.0 15.0
5mm
160
9.0
12.0 14.5
5mm
150
1.10
15.0
5mm
140
11.5
15.0
7.5
15.0
2.5 2.5
3.0/1.5 5.0
10.0
2.5 1.5
3.0/1.5
7.5
5.0
3.0
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 125
17.0
5mm
160 180
5mm
220
5mm
240 260
5mm 5mm
23.0 24.0
28.0 30.0
25.5
1.5 3.0
7.5
2.5 1.5
5.0
10.0
5.0
10.0
7.5
2.5 3.0
1.5
2.5 3.0
7.5
1.5
2.5
5.0 7.5
10.0 15.0
1.5 5.0
10.0 15.0
2.5 3.0
7.5 10.0
15.0
1.5
5.0
10.0 15.0
2.5 3.0
7.5
18.0 21.0
25.0 26.5
13.0 15.0
23.0
5mm
200
15.0
3.0 5.0
7.5
11.5
19.0
5mm
5.0
10.0
14.5
5mm
150
9.0
11.5 12.0
15.0
5mm
140
1.20
15.0
5mm
130
1.5
2.5
5.0 7.5
10.0
3.0
3.0
1.5
2.5
5.0 7.5
3.0 5.0
1.5
2.5 3.0
1.5
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
10
ComFlor
Quick Reference Load Span Table ComFlor 80 Single Span Sheets in Construction Simple Span Composite Slab - 30 minute fire rating ComFlor Quick Reference Load Span table - ComFlor 80 Single Span Sheets in Construction - Simple Span Composite Slab - 30 minute ďŹ re rating
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
145
15.0 5mm
150
5mm 15.0
160
5mm
170
0.75
15.0
5mm 5mm
2.5 3.0
7.5
1.5
5.0
10.0
2.5
3.0
7.5
1.5
5.0
10.0
5.0
2.5
3.0/1.5
7.5
15.0
2.5
3.0/1.5
7.5 10.0
>15.0
5mm
2.5 1.5
5.0
10.0
15.0
>15.0
1.5 3.0
7.5
12.0
>15.0
3.0 5.0
>15.0 15.0
5mm
220
5.0 7.5
15.0 13.0
5mm
200
7.5
10.5
5mm
190
260
15.0
5mm
180
240
10.0 10.0
2.5
5.0
10.0
3.0
7.5
15.0
10.0
>15.0
1.5
2.5
5.0/3.0/1.5
2.5
7.5
15.0
5.0/3.0/1.5
10.0
2.5
7.5
5.0/3.0
2.5
1.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 145
5mm
170
240 260
17.5
5mm 5mm 5mm
21.0
2.5
3.0 1.5
5.0/3.0 7.5
2.5
1.5
5.0/3.0/1.5
10.0
7.5
2.5
5.0/3.0/1.5
10.0
2.5
7.5
15.0
5.0/3.0
10.0
17.5 18.5
22.5
5.0
10.0
14.5 16.5
2.5
1.5
7.5
15.0
20.0
2.5
1.5
3.0
7.5
13.0
18.5
3.0 5.0
12.0 10.0
16.0
5mm
5.0 7.5
10.5
14.5
5mm
200
7.5
9.5
13.0
5mm
190 220
15.0
5mm
180
9.0
11.5
5mm 15.0
160
0.90
10.5
15.0 5mm
150
15.0
2.5
1.5
7.5
5.0/3.0/1.5
10.0
7.5
15.0
2.5 5.0/3.0/1.5 7.5
10.0
2.5 5.0/3.0
2.5
1.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 145
5mm
170 5mm
200 220
15.0
5mm 5mm 5mm
21.5 22.5
3.0
2.5
1.5
5.0/3.0
10.0
7.5
2.5
7.5
5.0/3.0
10.0
7.5
15.0
2.5
1.5
7.5
15.0
5.0/3.0/1.5
10.0
19.0
2.5
1.5
5.0/3.0
10.0
18.0
2.5
1.5
5.0/3.0/1.5
10.0
15.0 17.0
2.5
1.5
5.0 7.5
14.5
20.0
2.5
1.5
3.0
7.5
13.5
18.5
3.0 5.0
12.0 10.0
17.5
5mm
5.0 7.5
10.5
15.0 16.0
7.5
9.5
13.0
5mm
190
240 260
15.0
5mm
180
9.0
11.5
5mm 15.0
160
1.00
10.5
15.0 5mm
150
7.5
15.0
2.5 5.0/3.0
10.0
7.5
2.5 5.0/3.0/1.5
1.5
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 145
15.0 5mm
150
5mm
160
5mm
170
1.10
15.0
5mm
200
15.0
5mm
17.0
21.5
5mm
2.5
1.5
3.0
7.5
2.5
1.5
5.0
10.0
3.0
7.5
2.5
1.5
5.0/3.0/1.5
10.0
7.5
2.5
5.0/3.0/1.5
10.0
7.5
15.0
2.5
5.0/3.0/1.5
10.0
18.0 19.0
23.0
2.5
1.5
3.0 5.0
10.0
16.0
20.0
3.0 5.0
7.5
14.5
19.0
5mm
5.0 7.5
13.5
18.0
5mm
220
12.0
16.5
7.5
10.5
15.0
5mm
190
9.0 9.5
13.0
5mm
180
240 260
11.0 11.5
15.0
7.5
15.0
2.5 5.0/3.0/1.5
10.0
7.5
15.0
2.5 2.5
5.0/3.0/1.5
10.0
7.5
5.0/3.0/1.5
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 145
5mm
160
190 200 220 240 260
15.0
5mm
16.5
5mm 5mm
12.5 15.0
18.0 19.0 22.5 23.5
10.0
13.5
19.5 20.0
3.0 5.0
2.5 2.5
1.5
3.0
7.5 7.5 10.0
2.5
5.0/3.0/1.5 5.0/3.0/1.5
7.5 7.5 10.0
15.0
2.5
1.5
5.0/3.0/1.5
10.0 15.0
3.0
7.5 10.0
15.0
2.5
1.5
5.0
10.0
16.5 18.0
1.5
5.0 7.5
15.0
21.0
3.0
7.5
11.0
15.0
5mm 5mm 5mm
5.0
7.5
9.5
13.5
5mm
180
9.0
12.0
15.0
5mm
170
1.20
10.5
5mm 15.0
150
2.5 5.0/3.0/1.5
7.5 10.0
2.5 2.5 5.0/3.0/1.5 7.5
2.5 5.0/3.0/1.5
2.5
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
Composite floor decking www.comflor.co.nz
11
As part of the ComFlor policy of continuing product and system development, the company reserves the right, at any time and without notice, to discontinue or change the products, materials, design advice, features or specifications represented in this brochure without incurring any liability. Care has been taken to ensure that this information is accurate, but neither S&T Stainless nor its subsidiaries accept responsibility or liability for errors or information which is found to be misleading.
S&T STAINLESS Head Office 7 Bruce Roderick Drive East Tamaki Auckland 2013 P +64 9 271 1780 F +64 9 271 1970
CONTACT US TODAY:
+64 9 271 1780 www.comflor.co.nz