صمامات الخطوط

Page 1

Pipeline Valves

ORION S.p.A. via Caboto, 8 • 34148 Trieste • Italy • tel. +39 040813204 • fax +39 040811203 e mail sales@orionvalves.com • http://www.orionvalves.com


Single Disc Gate Valves 1

8 3 2

7 6 4

5

10

9

2


Cast steel, conduit type pipeline gate valves, single disc, outside screw and yoke, rising stem, electroless nickel plated disc, soft seats, removable yoke sleeve, gland repacking under pressure.

1

HANDWHEEL. The spoked handwheel is fabricated from steel pipe. The hub is coupled with the yoke sleeve by means of a tongue.

2

GLAND AND FLANGE. They are in forged steel and are supplied in two pieces, self aligning design to permit the gland to descend parallel to the stem even if the eyebolts are unevenly tightened.

3

GLAND BOLTS AND NUTS. The forged steel gland bolts are of the eyebolt type which can be swung outward for ease of gland repacking. They are fixed to the bonnet by hinge pins.

4

BONNET BOLTING. Bonnet studs and nuts are manufactured from alloy steel to the relevant ASTM standard.

5

BODY. The body is in cast steel and is carefully designed in all its details. The basic dimension, i.e. wall thickness, face to face and flanges comply with the relevant API and ANSI standards. The body-to-bonnet flange is circular, expect in the Class 150 which is oval. The body-to-bonnet joint are flat face on Class 150 valves, male-and-female on Class 300 and ring joint on Class 400 and above. Bosses are provided for drain taps.

6

BONNET. The bonnet is in cast steel. It is machined to accept yoke sleeve and incorporates a stuffing box dimensioned in accordance with the API standard.

7

BONNET BUSHING. The bonnet bushing or backseat is in forged stainless steel and forms part of the trim. Special attention is given to its machining.

8

9

10

STEM. The stem is in forged stainless steel and is part of the trim. The stem is provided with a T head. A ground backseat is provided to ensure a perfectly tight seal to the stuffing box when the valve is fully open. The stem is ground to minimize friction and prevent damage to gland packing. The threading is trapezoidal ACME type. Dimensions comply with the API 600 standard. SEAT RINGS. The rings are in forged stainless steel and are part of the trim. They are locked for install the springs. Special attention is given to the sealing surface which are ground and lapped for a perfectly seal. SLAB. The slab is part of the trim. It is forged stainless steel for diameters up to 12� and is in cast steel for larger valves. It is connected to the stem by means of a T joint. Special attention is given to the seating surfaces which are ground and lapped. REMARKS: A lantern ring is furnished only on request, in this case the stuffing box shall be tapped and fitted with an NPS 1/4 plug.

3


Class ANSI 150 (PN 20) FIGURE NUMBERS CLASS ANSI 150 – ALL SIZES SD 150 RF . . . . RAISED FACE SD 150 BW . . . WELDING ENDS C-D

Size RF BW C-closed D-open

RF

2” 177,8 215,9 450,5 517,5

3” 203,2 282,6 521,0 616,0

4” 228,6 304,8 582,0 703,0

6” 266,7 403,2 784,5 955,5

8” 292,1 419,1 922,0 1.150,0

10” 330,2 457,2 1.061,0 1.339,0

12” 355,6 501,7 1.159,0 1.487,0

14” 393,7 571,5 1.372,0 1.742,0

16” 406,4 609,6 1.477,0 1.892,0

18” 431,8 660,4 2.032,0 2.495,0

20” 457,2 711,2 1.365,0 1.515,0

24” 508,0 812,8 1.730,0 1.970,0

Size 26” RF 559,0 BW 864,0 C-closed 2.057,5 D-open 2.456,7

28” 610,0 914,0 2.185,9 2.606,4

30” 650,0 914,0 2.314,2 2.756,1

32” 965,0 711,0 2.442,6 2.905,8

34” 762,0 1.016,0 2.571,0 3.055,5

36” 800,0 1.016,0 2.699,4 3.205,2

40” 914,0 – 2.956,2 3.504,6

42” 965,0 – 3.084,5 3.654,3

48” 1.118,0 – 3.469,7 4.103,4

52” 1.300,6 – 3.726,5 4.402,8

56” 1.391,8 – 3.983,2 4.702,2

60” 1.483,1 – 4.240,0 5.001,6

26” 1.245,0 1.270,0 2.100,0 2.770,0

28” 1.346,0 1.372,0 2.320,0 3.031,0

C-D

BW

Class ANSI 300 (PN 50)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 300 – ALL SIZES SD 300 RF . . . . RAISED FACE SD 300 BW . . . WELDING ENDS SD 300 RJ . . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 215,9 231,8 451,0 518,0

3” 282,6 298,5 521,0 616,0

4” 304,8 320,7 583,0 704,0

6” 403,2 419,1 785,0 956,0

8” 419,1 435,0 922,0 1.150,0

10” 457,2 473,1 1.061,0 1.337,0

12” 501,7 517,5 1.169,0 1.499,0

16” 457,2 854,1 1.300,0 1.465,0

20” 990,6 1.009,7 1.730,0 2.247,0

24” 1.143,0 1.165,2 1.990,0 2.608,0

Size RF-BW RJ C-closed D-open

30” 1.397,0 1.422,4 2.625,0 3.411,0

32 1.524,0 1.553,0 2.750,0 3.512,0

34” 1.626,0 1.654,0 2.900,0 3.764,0

36” 1.727,2 1.755,8 2.960,0 3.886,0

40” 1.930,0 – 3.240,4 4.239,1

42” 2.007,0 – 3.387,9 4.436,3

48” 2.286,0 – 3.830,4 5.028,0

52” 2.433,2 – 4.125,4 5.422,4

56” 2.616,7 – 4.420,3 5.816,9

60” 2.800,3 – 4.715,3 6.211,4

C-D

BW

4

N.B. All dimensions are given in millimeters.


Class ANSI 400 (PN 68)

C-D

FIGURE NUMBERS CLASS ANSI 400 – ALL SIZES SD 400 RF . . . . RAISED FACE SD 400 BW . . . WELDING ENDS SD 400 RJ . . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 292,1 295,3 443,0 508,0

3” 355,6 358,8 523,0 616,0

4” 406,4 409,6 628,0 749,0

6” 495,3 498,6 778,0 949,0

8” 596,9 600,1 986,0 1.214,0

10” 673,1 676,3 1.160,0 1.440,0

12” 762,0 765,2 1.360,0 1.700,0

24” 1.231,9 1.241,4 2.120,0 2.750,0

36” 1.879,6 1.895,5 3.200,0 4.126,0

40” 1.930,4 – 3.280,0 4.310,0

RF-RJ

C-D

BW

Class ANSI 600 (PN 100)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 600 – ALL SIZES SD 600 RF . . . . RAISED FACE SD 600 BW . . . WELDING ENDS SD 600 RJ . . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 292,1 295,3 443,0 508,0

3” 355,6 358,8 523,0 616,0

4” 431,8 435,0 628,0 749,0

6” 558,8 562,0 778,0 949,0

8” 660,4 663,6 986,0 1.214,0

10” 787,4 790,6 1.228,0 1.511,0

12” 838,2 841,4 1.299,0 1.634,0

14” 889,0 892,2 1.466,0 1.834,0

16” 990,6 993,8 1.600,0 2.017,0

18” 1.092,0 1.095,0 1.680,0 2.138,0

20” 1.193,8 1.200,1 1.950,0 2.470,0

Size RF-BW RJ C-closed D-open

22” 1.295,4 1.305,0 2.060,0 2.630,0

24” 1.397,0 1.407,0 2.210,0 2.810,0

28” 1.549,4 1.562,1 2.633,0 3.359,0

32” 1.778,0 1.793,9 2.900,0 3.730,0

34” 1.930,0 1.946,0 3.075,9 3.947,2

36” 2.083,0 2.099,0 3.238,5 4.159,7

42” 2.438,0 – 3.726,3 4.797,5

48” 2.794,0 – 4.214,1 5.435,2

52” 2.894,4 – 4.539,3 5.860,4

56” 3.102,0 – 4.864,5 6.285,5

60” 3.309,6 – 5.189,7 6.710,7

C-D

BW

5


Class ANSI 900 (PN 150)

C-D

RJ

FIGURE NUMBERS CLASS ANSI 900 – ALL SIZES SD 900 RF . . . . RAIS ED FACE SD 900 BW . . . WELDING ENDS SD 900 RJ . . . . RING JOINT

Size RJ BW C-closed D-open

2” 368,0 371,0 443,0 508,0

3” 381,0 384,0 523,0 616,0

4” 457,0 460,0 628,0 749,0

6” 610,0 613,0 778,0 949,0

8” 737,0 740,0 986,0 1.214,0

10” 838,0 841,0 1.228,0 1.511,0

12” 965,0 968,0 1.299,0 1.634,0

Size RJ BW C-closed D-open

16” 1.130,0 1.140,0 1.600,0 2.017,0

20” 1.321,0 1.334,0 1.950,0 2.470,0

24” 1.549,4 1.568,5 2.210,0 2.835,0

26” 1.673,2 – 2.450,0 3.125,0

32” – 2.082,8 2.900,0 3.730,0

36” – 2.275,4 3.239,9 4.168,3

40,0 – 2.499,8 3.565,1 4.594,3

12” 1.130,0 1.146,0 2.119,3 2.474,0

14” 1.029,0 1.038,0 1.466,0 1.834,0

C-D

BW

Class ANSI 1500 (PN 250)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 1500 - ALL SIZES SD 1500 RF . . . RAIS ED FACE SD 1500 BW . . . WELDING ENDS SD 1500 RJ . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 368,0 371,0 443,0 503,0

3” 470,0 473,0 – –

4” 546,0 549,0 628,0 732,0

6” 705,0 711,0 1.135,0 1.315,0

8” 832,0 841,0 1.427,3 1.662,0

10” 991,0 1.000,0 1.773,3 2.068,0

Size RF-BW RJ C-closed D-open

16” 1.384,0 1.407,0 2.780,0 3.160,0

18” 1.537,0 1.559,0 2.990,0 3.420,0

20” 1.664,0 1.686,0 3.320,0 3.800,0

24” 1.971,4 – 4.195,3 4.910,0

26” 2.114,2 – 4.541,3 5.316,0

28” 2.257,0 – 4.887,3 5.722,0

C-D

BW

6

N.B. All dimensions are given in millimeters.

14” 1.257,0 1.276,0 2.460,0 2.800,0


Class ANSI 2500 (PN 420)

C-D

FIGURE NUMBERS CLASS ANSI 1500 – ALL SIZES SD 2500 RF . . . RAISED FACE SD 2500 BW . . . WELDING ENDS SD 2500 RJ . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 450,9 454,0 443,0 503,0

4” 673,1 682,6 628,0 732,0

6” 914,0 927,0 1.135,0 1.315,0

8” 1.022,0 1.038,0 1.427,3 1.662,0

10” 1.270,0 1.292,0 1.773,3 2.068,0

12” 1.422,0 1.445,0 2.119,3 2.474,0

14” 1.634,1 – 2.465,3 2.880,0

16” 1.827,1 – 2.811,3 3.286,0

RJ

C-D

BW

7


Expanding Gate Valves

1

8

3 2

4 7 6

5

9

10

8


Cast steel, conduit type pipeline expanding gate valves, outside screw and yoke, rising stem, tungsten carbide coated disc, soft seats, removable yoke sleeve, gland repacking under pressure.

1

HANDWHEEL The spoked handwheel is fabricated from steel pipe. The hub is coupled with the yoke sleeve by means of a tongue

2

GLAND AND FLANGE They are in forged steel and are supplied in two pieces, self aligning design to permit the gland to descend parallel to the stem even if the eyebolts are unevenly tightened.

3

GLAND BOLTS AND NUTS The forged steel gland bolts are of the eyebolt type which can be swung outward for ease of gland repacking. They are fixed to the bonnet by hinge pins.

4

BONNET BOLTING Bonnet studs and nuts are manufactured from alloy steel to the relevant ASTM standard.

5

BODY The body is in cast steel and is carefully designed in all its details. The basic dimension, i.e. wall thickness, face to face and flanges comply with the relevant API and ANSI standards. The body-to-bonnet flange is circular. Bosses are provided for drain taps.

6

BONNET The bonnet is in cast steel. It is machined to accept yoke sleeve and incorporates a stuffing box dimensioned in accordance with the API standard.

7

BONNET BUSHING The bonnet bushing or backseat is in forged stainless still and forms part of the trim. Special attention is given to its machining.

8

9

10

STEM The stem is in forged stainless steel and is part of the trim. The stem is provided with a T head. A ground backseat is provided to ensure a perfectly tight seal to the stuffing box when the valve is fully open. The stem is ground to minimize friction and prevent damage to gland packing. The threading is trapezoidal ACME type. Dimensions comply with the API 600 standard. SEAT RINGS The rings are in forged stainless and are part of the trim. They are locked for install the springs. Special attention is given to the seating surface which is ground and lapped, for a perfectly tight seal. DISC The Concave and Convex Disc are part of the trim. There are forged stainless steel. There are connected to the stem by means of a T joint. Special attention is given to the seating surfaces which are ground and lapped. REMARKS: A lantern ring is furnished only on request, in this case the stuffing box shall be tapped and fitted with an NPS 1/4 plug.

9


Class ANSI 600 (PN 100)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 600 - ALL SIZES EG 600 RF . . . . RAISED FACE EG 600 BW . . . . WELDING ENDS EG 600 RJ . . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 292,1 295,3 443,0 508,0

3” 355,6 358,8 523,0 616,0

4” 431,8 435,0 628,0 749,0

6” 558,8 562,0 778,0 949,0

8” 660,4 663,6 986,0 1.214,0

10” 787,4 790,6 1.228,0 1.511,0

12” 838,2 841,4 1.299,0 1.634,0

14” 889,0 892,2 1.466,0 1.834,0

16” 990,6 993,8 1.600,0 2.017,0

18” 1.092,0 1.095,0 1.680,0 2.138,0

20” 1.193,8 1.200,1 1.950,0 2.470,0

Size RF-BW RJ C-closed D-open

22” 1.295,4 1.305,0 2.060,0 2.630,0

24” 1.397,0 1.407,0 2.210,0 2.810,0

28” 1.549,4 1.562,1 2.633,0 3.359,0

32” 1.778,0 1.793,9 2.900,0 3.730,0

34” 1.930,0 1.946,0 3.075,9 3.947,2

36” 2.083,0 2.099,0 3.238,5 4.159,7

42” 2.438,0 – 3.726,3 4.797,5

48” 2.794,0 – 4.214,1 5.435,2

52” 2.894,4 – 4.539,3 5.860,4

56” 3.102,0 – 4.864,5 6.285,5

60” 3.309,6 – 5.189,7 6.710,7

C-D

BW

Class ANSI 900 (PN 150)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 900 – ALL SIZES EG 900 RF . . . . RAISED FACE EG 900 BW . . . . WELDING ENDS EG 900 RJ . . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 371,0 368,0 443,0 508,0

3” 384,0 381,0 523,0 616,0

4” 460,0 457,0 628,0 749,0

6” 613,0 610,0 778,0 949,0

8” 740,0 737,0 986,0 1.214,0

10” 841,0 838,0 1.228,0 1.511,0

12” 968,0 965,0 1.299,0 1.634,0

Size RF-BW RJ C-closed D-open

16” 1.140,0 1.130,0 1.600,0 2.017,0

20” 1.334,0 1.321,0 1.950,0 2.470,0

24” 1.568,5 1.549,4 2.210,0 2.835,0

26” – 1.673,2 2.450,0 3.125,0

32” 2.082,8 – 2.900,0 3.730,0

36” 2.275,4 – 3.239,9 4.168,3

40,0 2.499,8 – 3.565,1 4.594,3

C-D

BW

10

N.B. All dimensions are given in millimeters.

14” 1.038,0 1.029,0 1.466,0 1.834,0


Class ANSI 1500 (PN 250)

C-D

RF-RJ

FIGURE NUMBERS CLASS ANSI 1500 - ALL SIZES EG 1500 RF . . . RAISED FACE EG 1500 BW . . . WELDING ENDS EG 1500 RJ . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 368,0 371,0 443,0 503,0

3” 470,0 473,0 – –

4” 546,0 549,0 628,0 732,0

6” 705,0 711,0 1.135,0 1.315,0

8” 832,0 841,0 1.427,3 1.662,0

10” 991,0 1.000,0 1.773,3 2.068,0

Size RF-BW RJ C-closed D-open

16” 1.384,0 1.407,0 2.780,0 3.160,0

18” 1.537,0 1.559,0 2.990,0 3.420,0

20” 1.664,0 1.686,0 3.320,0 3.800,0

24” 1.971,4 – 4.195,3 4.910,0

26” 2.114,2 – 4.541,3 5.316,0

28” 2.257,0 – 4.887,3 5.722,0

8” 1.022,0 1.038,0 1.427,3 1.662,0

10” 1.270,0 1.292,0 1.773,3 2.068,0

12” 1.422,0 1.445,0 2.119,3 2.474,0

12” 1.130,0 1.146,0 2.119,3 2.474,0

14” 1.257,0 1.276,0 2.460,0 2.800,0

14” 1.634,1 – 2.465,3 2.880,0

16” 1.827,1 – 2.811,3 3.286,0

C-D

BW

Class ANSI 2500 (PN 420)

C-D

FIGURE NUMBERS CLASS ANSI 2500 - ALL SIZES EG 2500 RF . . . RAISED FACE EG 2500 BW . . . WELDING ENDS EG 2500 RJ . . . RING JOINT

Size RF-BW RJ C-closed D-open

2” 450,9 454,0 443,0 503,0

4” 673,1 682,6 628,0 732,0

6” 914,0 927,0 1.135,0 1.315,0

RF-RJ

C-D

BW

11


Swing Check Valves (Full Opening) 3 7

1

4 6

2

5

12


Cast steel, swing type disc, renewable body seat ring, bolted body-to-cover connection.

1

2

3

4

COVER. The cover is in cast or forged steel. The connection sealing surfaces are raised face or ring joint to suit the valve rating. BODY. The body is in cast steel, carefully designed so as to keep pressure drops to a minimun. A wide opening on the top of the body permits easy inspection and maintenance. The basic dimensions, wall thickness, face to face and flanges, comply with the relevant API and ASME standards. The body-to-cover flange is circular. The sealing surface for connection to the cover is recessed in the 150 and 300 lb Class and ring joint in the higher class. The body is threaded for a renewable seat and an integral over-travel stop for the disc is incorporated. Two threaded bosses are incorporated to ensure correct alignment of the hinge pin. Bosses are provided for drain taps or by-pass piping. COVER BOLTING. Cover studs and nuts are manufactured from alloy steel to the relevant ASTM standard. HINGE PIN. The hinge pin is part of the trim, in forged stainless steel and is machined from ground bar. The hinge pin is centred in the body with two threaded NPT plugs. The pin can be easily removed for maintenance of the valve.

5

SEAT RING. The ring is in forged stainless steel and is part of the trim. Its outer diameter is threaded and its bore is notched to easy installation and dismantling. Special attention is given to the seating face which is ground and lapped, for a perfectly tight seal. Welded-in seat ring may be supplied upon request.

6

DISC. The disc is part of the trim and is in forged stainless steel in diameters up to 12� and in cast steel for larger diameters. On the back face there is a threaded spigot for attachment to the hinge arm by a nut and split pin. The seating face is ground and lapped.

7

HINGE. The hinge is in forged steel for small diameters and in cast steel for valves from 14� upwards.

13


Class ANSI 150 (PN 20) FIGURE NUMBERS CLASS ANSI 150 - ALL SIZES RP 150 RF . . . . RAISED FACE RP 150 BW . . . . WELDING ENDS B

RF

Size RF-BW B

2” 203,2 165,0

21/2” 215,9 172,0

3” 241,3 190,0

4” 292,1 205,0

6” 355,6 262,0

8” 495,3 310,0

10” 622,3 355,0

12” 698,5 405,0

14” 787,4 445,0

16” 863,6 411,0

18” 977,9 515,0

20” 977,9 500,0

Size RF-BW B

22” 1.067,0 548,0

24” 1.295,0 730,0

26” 1.295,0 730,0

28” 1.448,0 677,0

30” 1.524,0 840,0

34” 1.651,0 1.000,0

36” 1.956,0 980,0

42” 2.083,0 950,0

48” 1.956,0 1.050,0

52” 2.448,2 1.241,2

56” 2.625,3 1.326,4

60” 2.802,5 1.411,6

Size RF-BW B

66” 3.068,3 1.539,4

16” 863,6 879,5 570,0

18” 977,4 993,8 526,0

20” 1.016,0 1.035,0 567,0

B

BW

Class ANSI 300 (PN 50)

B

FIGURE NUMBERS CLASS ANSI 300 – ALL SIZES RP 300 RF . . . . RAIS ED FACE RP 300 BW . . . . WELDING ENDS RP 300 RJ . . . . RING JOINT

Size RF-BW RJ B

2” 266,7 282,6 170,0

21/2” 292,1 308,0 189,0

3” 317,5 333,4 215,0

4” 355,6 371,5 240,0

6” 444,5 460,4 300,0

8” 533,4 549,3 308,0

10” 622,3 638,2 405,0

12” 711,2 727,1 450,0

14” 838,2 854,1 480,0

Size RF-BW RJ B

22” 1.118,0 1.140,0 740,0

24” 1.346,0 1.369,0 663,0

30” 1.594,0 – 822,0

36” 2.083,0 – 1.005,0

42” 2.215,4 – 1.130,8

48” 2.513,3 – 1.271,8

52” 2.711,9 – 1.365,8

56” 2.910,4 – 1.459,7

60” 3.109,0 – 1.553,7

RF-RJ

B

BW

N.B. All dimensions are given in millimeters.

14


Class ANSI 400 (PN 68)

B

FIGURE NUMBERS CLASS ANSI 400 – ALL SIZES RP 400 RF . . . . RAISED FACE RP 400 BW . . . . WELDING ENDS RP 400 RJ . . . . RING JOINT

SIZE RF-BW RJ B

2” 292,1 295,3 200,0

21/2” 330,2 333,4 215,0

3” 355,6 358,8 235,0

4” 406,4 409,6 235,0

SIZE RF-BW RJ B

26” 1.397,0 1.409,7 815,0

28” 1.600,2 1.612,9 845,0

36” 2.082,8 – 1.205,0

42” 2.184,4 – 1.310,0

6” 495,3 498,5 315,0

8” 596,9 600,1 380,0

10” 673,1 676,3 440,0

12” 762,0 765,2 450,0

16” 901,7 904,9 645,0

18” 1.016,0 1.019,2 690,0

20” 1.054,1 1.060,5 830,0

14” 889,0 892,2 595,0

16” 990,6 993,8 552,0

RF-RJ

B

BW

Class ANSI 600 (PN 100)

B

FIGURE NUMBERS CLASS ANSI 600 - ALL SIZES RP 600 RF . . . . RAISED FACE RP 600 BW . . . . WELDING ENDS RP 600 RJ . . . . RING JOINT

Size RF-BW RJ B

2” 292,1 295,3 200,0

21/2” 330,2 333,4 215,0

3” 355,6 358,8 235,0

4” 431,8 435,0 227,0

5” 508,0 511,0 295,0

6” 558,8 562,0 300,0

8” 660,4 663,6 357,0

10” 787,4 790,6 433,0

12” 838,2 841,4 456,0

Size RF-BW RJ B

18” 1.092,0 1.095,0 720,0

20” 1.194,0 1.200,0 663,0

24” 1.397,0 1.406,0 870,0

36” 2.083,0 2.099,0 1.235,0

42” 2.267,2 – 1.396,6

46” 2.460,3 – 1.517,6

52” 2.750,1 – 1.699,1

56” 2.943,2 – 1.820,1

60” 3.136,4 – 1.941,1

RF-RJ

B

BW

15


Class ANSI 900 (PN 150)

B

FIGURE NUMBERS CLASS ANSI 900 – ALL SIZES RP 900 RF . . . . RAISED FACE RP 900 RJ . . . . RING JOINT RP 900 BW . . . . WELDING ENDS

Size RF-BW RJ B

2” 368,3 371,5 255,0

21/2” 419,1 422,3 285,0

3” 381,0 384,2 250,0

4” 457,2 460,4 310,0

5” 558,8 562,0 365,0

6” 609,6 612,8 344,0

8” 736,6 739,8 418,0

10” 838,2 841,4 545,0

Size RF-BW RJ B

20” 1.321,0 1.334,0 928,0

24” 1.549,0 1.569,0 1.100,0

26” 1.930,0 1.953,0 1.300,0

28” 2.290,0 – 1.284,1

36” 2.342,9 – 1.612,4

42” 2.692,9 – 1.858,6

48” 3.043,0 – 2.104,8

52” 3.276,4 – 2.268,9

10” 990,6 1.000,0 675,0

12” 965,2 968,4 640,0

14” 1.029,0 1.038,0 680,0

16” 1.130,0 1.140,0 730,0

12” 1.130,0 1.146,2 730,0

14” 1.257,0 1.276,0 790,0

16” 1.384,0 1.407,0 852,0

RF-RJ

B

BW

Class ANSI 1500 (PN 250)

B

FIGURE NUMBERS CLASS ANSI 1500 - ALL SIZES RP 1500 RF . . . RAIS ED FACE RP 1500 RJ . . . RING JOINT RP 1500 BW . . . WELDING ENDS

Size RF-BW RJ B

2” 368,3 371,5 255,0

21/2” 419,1 422,3 285,0

3” 469,9 473,1 355,0

4” 546,1 549,3 350,0

5” 673,1 676,3 460,0

6” 704,9 711,2 445,0

8” 831,9 841,4 570,0

Size RF-BW RJ B

18” 1.537,0 1.559,0 1.030,0

20” 1.664,0 1.686,0 1.115,0

24” 1.943,0 1.972,0 1.130,0

28” 2.237,4 – 1.391,9

30” 2.378,1 – 1.476,2

34” 2.659,4 – 1.645,0

42” 3.222,0 – 1.982,6

RF-RJ

B

BW

N.B. All dimensions are given in millimeters.

16


Class ANSI 2500 (PN 420)

B

FIGURE NUMBERS CLASS ANSI 2500 - ALL SIZES RP 2500 RF . . . RAISED FACE RP 2500 RJ . . . RING JOINT RP 2500 BW . . . WELDING ENDS

Size RF-BW RJ B

2” 450,9 454,0 347,0

3” 577,9 584,2 400,0

4” 673,1 682,6 450,0

6” 914,4 927,1 600,0

8” 1.022,0 1.038,0 685,0

10” 1.252,3 – 812,2

12” 1.446,6 – 929,2

14” 1.641,0 – 1.046,1

16” 1.835,3 – 1.163,1

18” 2.029,6 – 1.280,1

20” 2.223,9 – 1.397,0

24” 2.612,6 – 1.631,0

RF-RJ

B

BW

17


Note

18


Note

19


Last Update: December 2004


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.