HOW TO USE The New 3D Printer
Content
Parts Included
…
page 2
Installing
…
page 3
Operating
…
page 5
Trouble-shooting
…
page 6
Specification
…
page 7
Customer Service
…
page 8
Parts Included top part navigate modules
printing module
connecting bar
steel bar
bottom part
Installing
Step 1 Place the bottom of the printer on a flat surface.
Note: the bottom is the heavier part and processing that contains battery unit. Don’t mistake between the top and the bottom.
Step 2 Attach 6 steel bars into the built in holes of the bottom part
Note: the bar would perfectly fit the built in holes. Don't attempt to push the bar, otherwise you will cause damage to the printer.
Step 3 Install the navigate modules to the bars using the built in holes of the modules
Note: after installation, the modules
should move smoothly along the bars. remove the If there is any error, modules and install again.
Step 4 Connect the plugs of the navigate modules to the socket on the bottom part.
WARNING: DON’T TOUCH THE METAL ON THE PLUGS DURING CONNECTING. THE BATTERY WILL CAUSE MINOR SHOCK IF CONTACT WITH THE PLUGS DURING INSTALLATION.
Step 5 Connect to top to the steel bars using the built-in holes of the top part.
Step 6 The installation ends with connecting the printing module to the navigate modules using the connecting bars, which are magnetism enabled
Operating
Step 1 Open FLUX Studio on your smartphone. Make sure your Bluetooth connection is turned on
Note: Other operating systems such as Windows or Mac OSX will be supported in December 2014.
Step 2 Choose one from the default design, or download from the FLUX store.
Note: You can also upload your design to the FLUX store. This feature will be available in December 2014.
Step 3 Press PRINT, and wait until your product is completed.
Note: a typical design will take from 30 to 40 minutes to complete. The time can be longer for complicated models
Trouble-shooting
Problem
Cause
Correction
1. The printer is out of battery.
1. Replace the battery with new one.
2. The material runs out. 3. Error in connection.
2. Recharge the material 3. Disable and re-enable the connection
My printer is shocking heavily in operation
1. The steel bar is connected incorrectly 2. The navigate bar is connected incorrectly 3. The printer is affected by the surrounding.
1. Remove the steel bar, then install again 2. Remove the connecting bar, then install again 3. Move the printer to a stable surface
My printer stops while printing a product
1. Material runs out
1. Recharge the material
2. The printer is overheat
2. Wait for the printer to cool down, then restart FLUX
1. The object is designed wrongly or incorrect format
1. Re-download the design from the FLUX store. If the error continues, report the design to FLUX store for assistance 2. Remove the connecting bar, then install again
My printer does not work
The printed object does not look like the design
2. The navigate bar is connected incorrectly
This topic does not cover your problem? Don’t worry; FLUX has a minimalist design with portable parts. When one part has problems, you just need to send
that part to the closest FLUX authorized store for replacement.
Or you can always go online for discussion and solution at: <http://flux3dp.com/discussion>
Specification
GENERAL Dimensions
21.7”H x 10.4”W x 11.8”L (30.5 cm x 26.5 cm x 55 cm)
Weight
12 lb (5.4 kg)
Power
100 – 240 V
I/O
USB / SD Card / Bluetooth 4.0
OS
iOS / Android
3D SCANNER Volume
5.5”D x 3.3”H (14 cm x 8.5 cm)
Maximum Power
5 mW
Wavelength
650 nm
Point Accuracy
2 – 3 mm
Triangles Per Model
60K – 100K
File Formats
STL / PCD / XYZ
Sensor
1.3M PIXELS CMOS
3D PRINTER
LASER ENGRAVER (under development) Work Area 5.9”D (15 cm)
Work Area
6.7”D x 7”H (17 cm x 18 cm)
Max Travel Speed
200 mm/s
X / Y Resolution
0.02 mm
Layer Height
0.05 – 0.3 mm
Max Power
200 mW
Nozzle Size
0.4 mm
Wavelength
405 nm InGaN
File Formats
STL / OBJ
File Formats
JPG / PNG / DXF / PDF / AI
Max Travel Speed X/Y Resolution
200 mm/s 0.02 mm
Customer Service
FLUX Store
FLUX Store
Causeway Bay
Oakridge
Hysan Palace
Westfield
500 Hennessy Road
925 Blossom Hill Road
Causeway Bay, Hong Kong
San Jose, CA 95123, U.S.A
(+852) 3979-3100
(+1) 408-960-0110
For the latest information of our innovative products for the future life, visit our web site at: <http://flux3dp.com/>
© FLUX Electronic N.V.2014 All right reserved. Specifications are subject to change without notice.
3140 350 21851
FLUX, FLUX 3D Printer and FLUX Electronics are the property of FLUX Electronics N.V. or their respective owners.
100% Recycled Paper 100% Papier Recyclé