Accesorii pentru lant si pentru cablu Total Race

Rigging Accessories g n i g g i R

Rigging Accessories

s e i r o s s ec c A

Copyright Š 2002 The Crosby Group, Inc. All Rights Reserved

123

Turnbuckles What It Takes To Be HG-223

³&URVE\ 2U (TXDO´

DESIGN The theoretical reserve capability of turnbuckles should be five times the Working Load Limit (FF-T-791). Known as the DESIGN FACTOR, it is usually computed by dividing the catalog ultimate load by the Working Load Limit. The ultimate load is the average load or force at which the product fails or no longer supports the load. The Working Load Limit is the maximum mass or force which the product is authorized to support in general service. The design factor is generally expressed as a ratio, such as 5 to 1.

COMPETITION Ask: What is the design factor?

Most competitors do not provide turnbuckle assemblies that exceed Crosby’s Working Load Limits with a design factor of 5 to 1.

HG-228

CROSBY All turnbuckles are designed with a design factor of at least 5 to 1.

Crosby turnbuckles have the highest Working Load Limits in the industry. Crosby working load limits and design factors are based on extensive testing.

HEAT TREATMENT Heat treatment assures the uniformity of performance and maximizes the properties of the steel. This assures that each turnbuckle will meet its rated strength. The requirements of your job demand this reliability and consistency. All turnbuckle bodies should be normalized to assure uniformity.

Turnbuckle end fittings are the components exposed to the highest stress, and should be quenched and tempered. This hardening and tempering process developes a tough material that reduces the risk of a brittle, catastrophic failure. This combination of heat treatment assures the performance of the turnbuckle assembly.

Ask: Do they utilize the combination of All turnbuckles are heat treated. heat treatment that assures the Bodies are normalized, and end performance of the turnbuckle assembly? fittings are quenched and tempered.

This combination of heat treatment provides a turnbuckle assembly that Most normalize both the turnbuckle has superior impact and fatique qualities and assures performance. body and end fittings. Some provide turnbuckles in an “as forged” condition.

GALVANIZE AND THREAD FORM Galvanizing provides the best resistance to corrosion.

Turnbuckle ends are the most highly stressed part of the assembly. This stress is at its peak at the root of the threaded shank. The turnbuckle ends should be threaded with a modified thread that minimizes the stress at the root of the thread.

Ask: Do they use the modified UNJ Thread?

FULL LINE AND IDENTIFICATION The proper application of turnbuckles requires that the correct type and size of turnbuckle be used. The turnbuckle size, the manufacturer’s LOGO, and a product identification code should be clearly and boldly marked in the end fittings as well as in the turnbuckle body. Traceability of the material chemistry is essential for total confidence in the manufacturer of the product. Availability over the full range of sizes of hook, eye, and jaw type turnbuckle assemblies are essential for flexibility in the design of a total system.

Ask: Do they have a traceability system?

Most galvanize their turnbuckles but do not utilize the modified thread.

Ask: Is the full range of type and size turnbuckles offered?

All turnbuckles are available galvanized. Turnbuckle ends are threaded with a modified UNJ thread. This thread form, in conjunction with quench and tempering gives Crosby turnbuckles their superior impact and fatigue performance.

Crosby forges its logo, sizes, and the Product Identification Code (PIC) into each component of its full line of hook, jaw, and eye type turnbuckles.

Most competitors do not have the full line that Crosby produces, or a traceability system.

Remember, “When buying Crosby, you’re buying more than product, you’re buying Quality.”

124

Copyright© 2002 The Crosby Group, Inc. All Rights Reserved

Crosby Value Added •

Charpy Impact Properties: Crosby’s quenched and tempered end fittings and normalized bodies have enhanced impact properties for greater toughness at all tempertures. If requested at the time of order, Crosby can provide Charpy impact properties.

•

Fatigue Properties: Typical fatigue properties are available for selected sizes. Crosby turnbuckles are designed with quenched and tempered end fittings and modified UNJ threads for improved fatique properties.

•

Typical Hardness Levels, Tensile Strengths and Ductility Properties: These properties are available for all sizes.

•

Inspection: If requested at the time of order, turnbuckles can be furnished proof tested or magnaflux inspected with certificates.

•

Full Line: Turnbuckle assembly combinations include: Eye and Eye, Hook and Hook, Hook and Eye, Jaw and Jaw, Jaw and Eye.

•

Hot Dip Galvanize: Turnbuckle components have a high quality “hot dip” galvanize finish. Self colored turnbuckle bodies are available upon request.

•

Jaw Ends: Jaw ends are fitted with bolts and nuts (1/4" through 5/8"), or pins and cotters (3/4" through 2-3/4").

•

Turnbuckle Eyes: Eyes are elongated by design, maximizing easy attachment in system and minimizing stress in the eye. For turnbuckle sizes 1/4" through 2-1/2", shackles one size smaller can be reeved through the eye.

•

Turnbuckle Hooks: Crosby Forges its turnbuckle hooks with a greater cross sectional area that results in a stronger hook with better fatigue properties.

•

Material Analysis: Crosby can provide certified material (mill) analysis for each production lot, traceable by the Product Identification Code (PIC). Crosby, through its own laboratory, verifies the analysis of each heat of steel.

Crosby purchased only special bar forging quality steel with specific cleanliness requirements and guaranteed hardenability.

HG-223 Hook & Hook

HG-225 Hook & Eye

HG-226 Eye & Eye

Meets the performance Meets the performance Meets the performance requirements of Federal requirements of Federal requirements of Federal Specifications FF-T-791b, Specifications FF-T-791b, Specifications FF-T-791b, Type 1, Form 1, Class 6, Type 1, Form 1, Class 4, Type 1, Form 1, Class 5, and ASTM F-1145, except and ASTM F-1145, except and ASTM F-1145, except for those provisions for those provisions for those provisions required of the contractor. required of the contractor. required of the contractor.

HG-227 Jaw & Eyes

HG-228 Jaw & Jaw

HS-251 Stub End

Meets the performance Meets the performance Meets the performance requirements of Federal requirements of Federal requirements of Federal Specifications FF-T-791b, Specifications FF-T-791b, Specifications FF-T-791b, Type 1, Form 1, Class 8, Type 1, Form 1, Class 7, Type 1, Form 1, Class 3, and ASTM F-1145, except and ASTM F-1145, except and ASTM F-1145, except for those provisions for those provisions for those provisions required of the contractor. required of the contractor. required of the contractor.

Remember, “When buying Crosby, you’re buying more than product, you’re buying Quality.”

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

125

Wire Rope Thimbles G-411

• The standard choice for light duty applications and loading conditions.

• Hot Dip galvanized steel. s e l b mi

h T

e p o R

e r i W

G-411 m eet s t he performance requirement s of Federal Spec ific ation FF-T-276b Type II, exc ept for t hose provisions required of t he c ont ractor.

Standard Wire Rope Thimbles Ro pe Dia. (mm) 3-4 5 6-7 8 9-10 11-13 16 18-20 22 24-26 28-32

G-414

G -411 Stock No. 1037256 1037274 1037292 1037318 1037336 1037354 1037372 1037390 1037416 1037434 1037452 -41 G

Weig ht Per 100 (kg ) 1.59 1.59 1.59 1.81 3.04 5.67 15.7 21.4 38.4 44.2 79

A 49.3 49.3 49.3 54.0 60.5 70.0 89.0 95.5 127 145 159

B 33.3 33.3 33.3 38.1 41.4 47.8 57.0 63.5 89.0 108 114

C 26.9 26.9 26.9 31.8 37.3 44.5 60.5 68.5 81.0 95.5 109

Dimension s (mm) D E 17.5 6.35 17.5 7.85 17.5 9.65 20.6 11.2 23.9 13.5 28.7 17.5 35.1 23.1 41.4 27.4 47.8 32.3 63.5 35.3 70.0 44.5

F 4.05 5.60 7.10 8.65 10.4 13.5 16.8 19.8 23.9 26.9 33.3

G 1.25 1.25 1.25 1.25 1.50 2.05 3.30 3.55 4.05 4.05 5.60

H 3.30 3.30 3.30 3.30 4.06 4.83 8.64 8.64 11.2 10.4 12.7

• Greater protection against wear and deformation of the wire rope eye.

• Longer service life.

• Available in Hot Dip galvanized or Stainless Steel (Type 304).

• Stainless steel recommneded for more corrosive environments where greater protection is required. s

e l b mi h T

e p o R

e

r i W

G-414 m eet s t he performance requirement s of Federal Spec ific ation FF-T-276b Type III, except for t hose provisions required of t he c ont ractor.

Extra Heavy Wire Rope Thimbles Rope Dia. (mm .)* * 6-7 *8 * 9-10 * 11-12 * 13-15 * 16 * 18-20 22 24-26 28-32 32-35 35-38 40 44 48-52 56

Stock G-414 Galv.

1037639 1037657 1037675 1037693 1037719 1037755 1037773 1037791 1037817 1037835 1037853 1037871 1037899 1037915 1037933 1037951

No. SS-414 Stainless 1037960 1037988 1038004 1038022 1038040 1038068 41 G

Weigh t Per 100 (kg) 2.95 5.35 9.80 15.7 23.1 34.3 72 81 142 181 368 587 771 805 1259 1792

Dimension s (m m) A 55.5 63.5 73.0 82.5 92.0 108 127 140 156 178 230 229 286 310 384 435

B 41.4 47.8 54.0 60.5 70.0 82.5 95.5 108 114 130 165 159 203 229 305 356

C 38.1 46.0 54.0 60.5 70.0 79.5 96.5 108 125 149 173 181 207 216 264 302

D 22.4 26.9 28.7 31.8 38.1 44.5 51.0 57.0 63.5 73.0 89.0 89.0 102 114 152 178

E 10.4 12.7 16.0 18.3 20.6 24.6 31.0 35.1 39.6 46.0 55.5 65.0 69.0 72.0 78.5 92.0

F 7.10 8.65 10.4 11.9 13.5 16.8 19.8 23.9 26.9 33.3 36.6 39.6 43.7 46.7 53.0 60.5

G 1.50 2.05 2.80 3.30 3.55 4.05 5.60 5.60 6.35 6.35 9.65 12.7 12.7 12.7 12.7 16.0

H 5.85 7.10 8.65 9.65 10.4 12.7 16.8 19.1 22.4 28.7 28.7 28.7 35.1 33.3 38.1 41.4

* S S-414 sizes available in stainless steel type 304.

126

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Wire Rope Thimbles s e l b mi

h T

e p o R

e r i W

G-408 (OPEN PATTERN)

Open Pattern Thimbles • Recommended for light duty applications in which it is being assembled into another fitting (i.e., shackle or master link).

• Hot Dip galvanized Steel.

-408 G

G-408 Stock No. 1037531 1037559 1037577 1037595 1037611

Weight Per 100 (kg) 1.36 1.72 3.18 5.67 11.3

A 7.10 8.65 11.2 13.5 16.8 s

e l b mi h T

e p o R

Dim en sions (mm) C D 26.9 35.8 31.8 38.9 37.3 43.7 44.5 37.3 60.5 59.5

B 17.5 20.6 23.9 28.4 35.1 e

E 51.5 55.0 62.5 72.0 91.0

F 9.65 12.7 15.7 19.1 25.4

Rigging Accessories

Rope Dia. (m m) 6-7 8 9-10 11-13 16

r i W

S-412

Solid Wire Rope Thimbles • Fits pin for open wire rope socket, boom pendant clevis and wedge socket.

• Cast Ductile Iron.

Dimen sio ns (mm)

-412 S

Ro pe Dia. (mm ) 13 16 18-20 22 24-26 28-30 32-35

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

S-412 Stock No. 1037121 1037149 1037167 1037185 1037201 1037229 1037247

Weigh t Each (kg) .28 1.00 1.05 2.47 2.38 4.21 4.45

A 71.5 119 119 154 154 184 184

B 44.5 76.0 76.0 97.0 97.0 116 116

C 6.35 9.65 9.65 12.7 12.7 16.0 16.0

D 26.9 33.3 38.1 44.5 54.0 60.5 67.0

E 19.1 26.9 26.9 35.1 35.1 44.5 49.3

F 14.2 20.6 20.6 26.9 26.9 33.3 38.9

G 7.10 10.4 10.4 13.5 13.5 16.8 19.8

H 22.4 28.7 35.1 41.4 46.0 52.5 58.5

J 54.0 86.0 86.0 114 114 137 137

K 41.4 57.0 57.0 82.5 82.5 98.5 98.5

L 39.6 65.0 65.0 87.5 87.5 103 105

127

Alloy Master Links A-342

• Alloy Steel — Quenched and Tempered.

• Individually proof tested to v alues shown.

• For use with chain (S.F.= 4/1), prooftested to 2.5 times the working load limit.

• For use with rope (S.F.= 5/1), prooftested to 2 times the working load limit.

• Sizes from 13 mm to 51 mm are drop forged. s k n i L

r e t s a M

y

o l l A

A-342 and A-345 Master Links incorporate markings forged into the product which address two (2) QUIC-CHECK® features: Deformation Indicators — Two strategically placed marks, one on each side of the link, which allows for a QUIC-CHECK ® measurement to determine if the link dimensions have changed, thus indicating abuse or overload.

To check, use a measuring device (i.e., tape measure) to measure the distance between the marks. The marks should meet the dimensions as shown in the table. If the measurement does not meet this criteria, the Master Link should be inspected further for possible damage.

Angle Indicators: Forged at 45° angles at each end of the link, they are utilized to quickly check the approximate included angles between two sling legs.

A-342 Alloy Master Links Size "A" (mm) ** 13 ** 16 ** 19 ** 22 ** 25 ** 32 ** 38 ** 44 ** 51 †† 57 **†† 63 †† 70 †† 76 †† 83 †† 89 †† 95 †† 102 †† 108 †† 121 †† 121 †† 127

-342 A

A-342 Stock No. 1014262 1014280 1014306 1014315 1014324 1014342 1014360 1014388 1014404 1014422 1014468 1014440 1014486 1014501 1014529 1015051 1015060 1015067 1015079 1015088 1015094

Working Load Limit S.F.= 5:1 F or Ro pe (t)* 3.17 4.08 5.58 6.44 11.05 16.42 25.67 38.51 46.54 65.6 66.8 98.4 103 119 126 152 169 160 163 176 179

Wo rking Lo ad Limit S.F.= 4:1 F or Chain (t)* 2.54 3.26 4.46 5.15 8.83 13.13 20.54 30.81 37.23 52.47 58.00 78.71 82.73 95.13 101 122 135 128 130 141 143

Dimensions (mm ) Proofload in kN ** 63 81 110 127 217 323 504 756 913 1287 1311 1930 2029 2334 2483 2990 3319 3150 3204 3462 3515

Weigh t Each (kg) .37 .69 .94 1.59 2.20 4.34 7.36 11.4 16.8 24.5 30.7 39.8 52 66 91 90 103 137 156 198 234

B 63.5 76.0 70.0 95.5 89.0 111 133 152 178 203 203 241 229 254 305 254 254 305 356 356 381

C 127 152 140 162 178 222 267 305 356 406 406 406 457 508 610 508 508 610 711 711 762

Deformation In dicator 76 89 89 114 114 140 165 191 229 -

* Based on single leg sling (in-line load), or resultant load on multiple legs with an included angle less than or equal to 120 degrees. ** Proof test load equals or exceeds the requirement of AS TM A957(8.1) and ASME B30.9-1.4 for the chain size and number of legs. For use with chain slings, see page 166. † † Welded Master Link.

128

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

COLD-TUFF® Fittings A-342CT

• Alloy Steel - Quenched and Tempered • Individually proof tested at 2 times Working Load Limit with certification.

• Certified to meet charpy impact testing of 42 J min. ave. at -20° C. • Individually serialized and all certification shipped with each link.

• Links are certified in accordance with DNV specification 2.7-1-Offshore Containers and DNV rules for Lifting Appliances - Loose Gear.

• Finish is Inorganic Zinc Primer. s g n i t t i F

®

F F UT - DL OC

A-342CT Master Links Size (mm) 31.8 38.1 44.5 51.0

A-342CT Sto ck No .

1261401 1261412 1261423 1261433

Working Load Limit (t) * 15.9 21.7 28.3 44.3

Weigh t Each (kg) 4.42 7.77 11.8 18.7

Dimen sio ns (mm) A 31.8 38.1 44.5 51.0

B 111 133 152 178

C 222 267 305 356

D 175 210 241 279

E 286 343 394 457

Deformation Ind icator 140 165 191 229

* Minimum Ultimate Load is 5 times the Working Load Limit.

s g n i t t i F

®

F F UT - DL OC

A-345CT

A-345CT Master Link Assembly • Alloy Steel - Quenched and Tempered • Individually proof tested at 2 times Working Load Limit with certification.

• Links are certified in accordance with DNV specification 2.7-1-Offshore Container and DNV rules for Lifting Appliances - Loose Gear.

• Certified to meet charpy impact testing of 42 J min. ave. at - 20° C. • Finish is Inorganic Zinc Primer.

-345CT A

Size (mm ) 31.8 38.1 44.5 51.0

A-345CT Stock No .

1261609 1261620 1261631 1261642

Working Lo ad Limit (t) * 15.9 21.7 28.3 44.3

Weight Each (kg) 13.6 23.1 35.4 56

Dimensio ns (mm) A

B 31.8 38.1 44.5 51.0

C 111 133 152 178

222 267 305 356

* Minimum Ultimate Load is 5 times the Working Load Limit.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

129

Rigging Accessories

-342C A T

Links and Rings s

G-340

g n i R

d n a

s k

n i L

S-340

G-340 from 16mm t hru 22m m m eet t he performance requirem ents of Federal Specification RRC-271D, T ype XV, exc ept for those provision s required of the contractor.

Weldless End Links • Self Colored or Hot Dip galvanized.

• Forged carbon steel - Quenched and Tempered Size (A) (mm) 8 9-10 11-13 16 18-20 22 24-26 32 35

Sto ck N o.

G-340 S-340 Galv.

S.C. 1014057 1014066 1014075 1014084 1014093 1014100 1014119 1014128 1014137 1014146 1014155 1014164 1014173 1014182 1014191 1014208 1014217 1014226 -340 G

Workin g Load Limit (t)* 1.13 1.72 2.95 4.22 6.35 5.44 6.89 11.97 13.61

Weigh t Each (kg) .07 .10 .22 .44 .68 1.17 1.79 3.31 4.71

Dimensions (m m) B 12.7 14.2 19.1 25.4 28.7 51.0 57.0 63.5 70.0

C 44.5 47.8 60.5 82.5 89.0 130 146 178 197

D 30.0 35.1 46.0 59.0 68.0 95.5 108 127 140

* Ultimate Load is 5 times the Working Load Limit. Based on single leg sling (in-line load), or r esultant load on multiple legs with an included angle less than or equal to 120°.

s g n

i R

d n

a

s k n

i L

S-643

Weldless Rings meet t he p erformanc e requirements of Federal Specification RRC-271D T ype VI, except for those p rovisions required of the contractor.

S-643 Weldless Rings • Self Colored • Forged carbon steel - Quenched and Tempered.

Size (A) (m m) 22.2 x 102 22.2 x 140 25.4 x 102 28.6 x 152 31.8 x 127 34.9 x 152

-643 S

S-643 Stock No. 1013780 1013806 1013824 1013842 1013860 1013888

Working Load L imit Sing le Pull (t) * 3.27 2.54 4.90 4.72 7.71 8.62

Weight Each (kg) 1.23 1.57 1.67 2.99 3.09 4.59

Dimen sio ns (mm) B 102 140 102 152 127 152

C 146 184 152 210 191 222

* Ultimate Load is 6 times the Working Load Limit.

130

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Pear Shaped Links A-341

• Alloy Steel - Quenched and Tempered • Individually Proof Tested at 2 times Working Load Limit with certification.

• Proof Test certification shipped with each link.

• Sizes 13mm, 16mm, 19mm, and 25mm are drop forged. s k n i L

d

e p a h S

r a e P

Stock Size (A) (mm ) 13 16 19 †† 22 25 †† 28 †† 32 †† 35 †† 38 †† 42 †† 44 †† 48 †† 51 †† 57 †† 64 †† 70 †† 76 †† 83 †† 89 †† 102

Working L oad Limit (t) * 3.15 4.09 5.59 6.36 11.0 13.9 16.4 19.5 24.7 28.4 38.6 43.5 46.6 65.0 66.9 98.6 103 119 126 169

-341 A

A-341 Stock No. 1013575 1013584 1013595 1013604 1013613 1013622 1013631 1013640 1013649 1013658 1013667 1013676 1013685 1013694 1013703 1013712 1013721 1013730 1013739 1013748

Weigh t Each (kg) .25 .50 .80 1.28 1.91 2.83 3.74 5.10 6.46 8.39 10.2 13.2 15.4 21.8 29.9 39.9 52 66 82 123

B 38.1 47.8 57.0 67.0 76.0 86.0 95.5 105 114 124 133 143 152 171 191 210 229 248 267 305

C 25.4 31.8 38.1 44.5 51.0 57.0 63.5 70.0 76.0 82.5 89.0 95.5 102 114 127 140 152 165 178 203

Dimension s (m m) D 102 127 152 178 203 222 254 279 305 330 356 381 406 457 508 559 610 660 711 813

E 76.2 95.3 114 133 152 171 191 210 229 248 267 286 305 343 381 419 457 495 533 610

F 12.7 16.0 19.1 22.4 25.4 28.7 31.8 35.1 38.1 41.4 44.5 47.8 51.0 57.0 63.5 70.0 76.0 82.5 89.0 102

* Based on single leg sling (in-line load), or resultant load on multiple legs with an included angle less than or equal to 120°. Minimum Ultimate load is 5 times the Working Load Limit. † † Welded Master Link.

G-341 / S-341

• Self Colored or Hot Dip galvanized.

• Forged carbon steel - Quenched and Tempered. s k n i L

d e p a h S

r a e P

G-341 S-341 Weldless Sling Links Size (A) (mm) 9-10 11-13 16 18-20 22 24-26 32 35

Stock G-341 Galv.

1013897 1013913 1013931 1013959 1013977 1013995 1014011 1014039

No. S-341 S.C. 1013904 1013922 1013940 1013968 1013986 1014002 1014020 1014048 -341 G

Wo rking Load Limit Sin gle Pu ll (t)* .82 1.32 1.91 2.72 3.76 4.90 7.60 9.30

Weigh t Each (kg) 0.10 .25 .48 .85 1.25 1.97 3.45 5.13

Dimensions (mm ) B 28.7 38.1 47.5 57.0 67.0 76.0 102 105

C 19.1 25.4 31.8 38.1 44.5 51.0 63.5 70.0

D 76.0 102 127 152 178 203 260 279

E 57.0 76.0 95.5 114 133 152 191 210

F 9.65 12.7 16.0 19.1 22.4 25.4 31.8 35.1

* Ultimate Load is 6 times the Working Load Limit. Based on single leg sling (in-line load), or resultant load on multiple legs with an included angle less than or equal to 120°.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

131

Rigging Accessories

A-341 Alloy Pear Shaped Links

Forged Eye Bolts SEE APPLICATION AND WARNING INFORMATION On Pages 154-155

G-291

• Recommended for straight line pull.

• All Bolts Hot Dip galvanized after threading (UNC).

• Furnished with standard Hot Dip galv anized hex nuts.

• Forged Steel - Quenched and Tempered.

• Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles. s

t l o B

e y E

d e

g r o F

G-291 Regular Nut Eye Bolts Shan k Dia. & Len gth (mm ) 6.35 x 51.0 6.35 x 102 7.94 x 57.0 7.94 x 108 9.53 x 63.5 9.53 x 114 9.53 x 152 12.7 x 82.5 12.7 x 152 12.7 x 203 12.7 x 254 12.7 x 305 15.9 x 102 15.9 x 305 15.9 x 203 15.9 x 254 15.9 x 305 19.1 x 114 19.1 x 152 19.1 x 203 19.1 x 254 19.1 x 305 19.1 x 381 22.2 x 127 22.2 x 203 22.2 x 305 25.4 x 152 25.4 x 229 25.4 x 305 25.4 x 457 31.8 x 203 31.8 x 305 31.8 x 508

-291 G

G-291 Sto ck No .

1043230 1043258 1043276 1043294 1043310 1043338 1043356 1043374 1043392 1043418 1043436 1043454 1043472 1043490 1043515 1043533 1043551 1043579 1043597 1043613 1043631 1043659 1043677 1043695 1043711 1043739 1043757 1043775 1043793 1043819 1043837 1043855 1043873

Working Lo ad Limit (t) * .29 .29 .54 .54 .70 .70 .70 1.18 1.18 1.18 1.18 1.18 2.35 2.35 2.35 2.35 2.35 3.26 3.26 3.26 3.26 3.26 3.26 4.80 4.80 4.80 6.03 6.03 6.03 6.03 9.52 9.52 9.52

Weigh t Per 100 (kg) 3.72 5.31 6.03 11.3 10.6 13.4 16.0 22.8 30.0 37 40 52 47 54 61 70 76 76 84 94 107 117 135 122 140 181 191 213 245 295 340 408 549

Dim en sions (mm) A 6.35 6.35 7.85 7.85 9.65 9.65 9.65 12.7 12.7 12.7 12.7 12.7 15.7 15.7 15.7 15.7 15.7 19.1 19.1 19.1 19.1 19.1 19.1 22.4 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8

B 12.7 12.7 15.7 15.7 19.1 19.1 19.1 25.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 31.8 31.8 38.1 38.1 38.1 38.1 38.1 38.1 44.5 44.5 44.5 51.0 51.0 51.0 51.0 63.5 63.5 63.5

C 25.4 25.4 31.8 31.8 38.1 38.1 38.1 51.0 51.0 51.0 51.0 51.0 63.5 63.5 63.5 63.5 63.5 76.0 76.0 76.0 76.0 76.0 76.0 89.0 89.0 89.0 102 102 102 102 127 127 127

D 6.35 6.35 7.85 7.85 9.65 9.65 9.65 12.7 12.7 12.7 12.7 12.7 15.7 15.7 15.7 15.7 15.7 19.1 19.1 19.1 19.1 19.1 19.1 22.4 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8

E 38.1 63.5 38.1 63.5 38.1 63.5 63.5 38.1 76.0 76.0 76.0 76.0 51.0 76.0 76.0 76.0 102 51.0 76.0 76.0 76.0 102 127 63.5 102 102 76.0 102 102 178 102 102 152

F 51.0 102 57.0 108 63.5 114 152 82.5 152 203 254 305 102 152 203 254 305 114 152 203 254 305 381 127 203 305 152 229 305 457 203 305 508

G 77.5 129 90.5 141 105 155 194 137 206 257 308 359 170 221 272 322 373 195 233 284 335 386 462 222 298 400 262 338 414 567 340 441 645

H 14.2 14.2 17.5 17.5 22.4 22.4 22.4 28.4 28.4 28.4 28.4 28.4 36.6 36.6 36.6 36.6 36.6 42.9 42.9 42.9 42.9 42.9 42.9 51.0 51.0 51.0 58.5 58.5 58.5 58.5 73.0 73.0 73.0

* Ultimate Load is 5 times the Working Load Limit. Working Load Limit shown is for in-line pull.

Maximum Proof Load is 2 times the Working Load Limit.

132

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Forged Eye Bolts SEE APPLICATION AND WARNING INFORMATION On Pages 154-155

G-277

• Forged Steel.

• All Bolts Hot Dip galvanized after threading (UNC).

• Furnished with standard Hot Dip galvanized, heavy hex nuts.

• Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles. s

t l o B

e

y E

d e g

r o F

G-277 Shoulder Nut Eye Bolts -277 G

G-277 Sto ck No .

1045014 1045032 1045050 1045078 1045096 1045112 1045130 1045158 1045176 1045194 1045210 1045238 1045256 1045292 1045318 1045336 1045354 1045372

Working Lo ad Lim it (t)* .29 .29 .54 .54 .70 .70 1.18 1.18 2.35 2.35 3.26 3.26 4.80 6.03 6.03 9.52 9.52 10.8

Dimensio ns (mm)

Weig ht Per 100 (kg ) 2.99 4.13 5.67 8.53 9.71 11.5 19.3 25.8 31.1 46.4 66 76 102 166 192 295 361 646

A 6.35 6.35 7.85 7.85 9.65 9.65 12.7 12.7 15.7 15.7 19.1 19.1 22.4 25.4 25.4 31.8 31.8 38.1

B 12.7 12.7 15.7 15.7 19.1 19.1 25.4 25.4 31.8 31.8 38.1 38.1 44.5 51.0 51.0 63.5 63.5 76.0

C 22.4 22.4 28.4 28.4 35.1 35.1 44.5 44.5 57.0 57.0 70.0 70.0 82.5 95.5 95.5 114 114 140

D 4.85 4.85 6.35 6.35 7.85 7.85 9.65 9.65 12.7 12.7 15.7 15.7 19.1 22.4 22.4 25.4 25.4 31.8

E 38.1 63.5 38.1 63.5 38.1 63.5 38.1 76.0 51.0 76.0 51.0 76.0 63.5 76.0 102 102 102 152

F 51.0 102 57.0 108 63.5 114 82.5 152 102 152 114 152 127 152 229 203 305 381

G 74.5 125 89.0 140 101 152 130 200 164 214 189 227 215 253 329 323 425 527

H 12.7 12.7 17.5 17.5 19.8 19.8 25.4 25.4 33.3 33.3 39.6 39.6 46.7 53.0 53.0 62.5 62.5 76.0

J 11.9 11.9 14.2 14.2 16.8 16.8 23.1 23.1 28.4 28.4 35.1 35.1 39.6 46.0 46.0 58.0 58.0 70.0

* Ultimate Load is 5 times the Working Load Limit. Working Load Limit shown is for in-line pull. Maximum Proof Load is 2 tim es the Working Load Limit.

G-275

• Forged Steel — Quenched and Tempered.

• Hot Dip galvanized. s t

l o B

e y

E

d e g r

o F

G-275 Screw Eye Bolts Shank Diameter & L ength (m m) 6.35 x 51.0 7.94 x 57.0 9.53 x 63.5 12.7 x 82.5 15.9 x 102

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

- 275 G

G-275 Sto ck N o.

1046111 1046139 1046157 1046175 1046193

Weight Per 100 (kg) 1.95 4.49 8.56 17.0 38.8

Dimensions (m m) A 6.35 7.85 9.65 12.7 16.0

B 38.1 42.9 47.8 62.0 76.0

C 51.0 57.0 63.5 82.5 102

D 63.5 74.5 83.5 108 135

E 74.5 89.0 101 130 164

F 12.7 16.0 19.1 25.4 31.8

G 22.4 28.7 35.1 44.5 57.0

H 4.83 6.35 7.87 9.65 12.7

J 11.9 14.2 16.8 23.1 28.4

133

Rigging Accessories

Shan k Diameter & Length (mm) 6.35 x 51.0 6.35 x 102 7.94 x 57.0 7.94 x 108 9.53 x 63.5 9.53 x 114 12.7 x 82.5 12.7 x 152 15.9 x 102 15.9 x 305 19.1 x 114 19.1 x 152 22.2 x 127 25.4 x 152 25.4 x 229 31.8 x 203 31.8 x 305 38.1 x 381

Forged Machinery Eye Bolts SEE APPLICATION AND WARNING INFORMATION On Pages 154-155

S-279 / M-279

• Forged Steel - Quenched & Tempered.

• Working Load Limits shown are for In-line pull.

• Recommended for straight line pull.

• Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.

• S-279 threaded UNC. • M-279 metric threaded. s t l o B

e y E

y r

e n i h c a M

d e g r o F

Shoulder Type Machinery Eye Bolts

S-279 UNC -279 S

Size 6.35 x 25.4 7.94 x 28.6 9.53 x 31.8 12.7 x 38.1 15.9 x 44.5 19.1 x 51.0 22.2 x 57.0 25.4 x 63.5 31.8 x 76.0 38.1 x 89.0

S-279 Stock No .

9900182 9900191 9900208 9900217 9900226 9900235 9900244 9900253 9900262 9900271

Working Load Limit (t) * .29 .54 .70 1.18 2.35 3.26 4.08 6.03 9.52 10.8

Weight Each (kg) .02 .04 .06 .12 .24 .43 .70 1.1 1.8 3.2

Dimensions (m m) A** Thread 1/4 - 20 5/16 - 18 3/8 - 16 1/2 - 13 5/8 - 11 3/4 - 10 7/8 - 9 1-8 1-1/4 - 7 1-1/2 - 6

B 25.9 29.2 32.3 38.9 45.5 52.0 58.5 65.5 78.5 91.5

C 28.7 35.1 41.1 49.5 60.5 70.0 82.5 95.5 114 140

D 19.1 22.4 25.4 30.2 35.1 38.1 44.5 51.0 63.5 76.0

E 58.0 69.5 78.0 94.0 113 129 149 169 202 241

F 4.85 6.35 7.85 9.65 12.7 16.0 19.1 22.4 25.4 31.8

G 13.5 15.0 17.5 23.1 28.7 35.1 39.6 46.0 58.0 70.0

* Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Lim it. ** All bolts threaded UNC.

M-279 Metric -279 M

Size M6 M8 M 10 M 12 M 16 M 20 M 24 M 30 M 36

M-279 Stock No .

10457534 10457894 10458334 10458694 10459134 10459954 10460294 10460754 10461094

Working Load Limit (kg) * 200 400 640 1000 1800 2500 4000 6000 8500

Weight Each (kg) .03 .05 .08 .18 .40 .90 .95 1.6 2.7

Dimensions (m m) A** Thread 6 8 10 12 16 20 27 30 36

B 13.0 13.0 17.0 20.5 27.0 30.0 36.0 45.0 54.0

C 28.7 35.1 41.1 49.5 60.5 70.0 95.5 114 140

D 19.1 22.4 25.4 30.2 35.1 38.1 51.0 53.5 76.0

E 58.0 59.7 78.0 94.0 113 129 169 202 241

F 4.9 6.4 7.9 9.7 12.7 16.0 22.4 25.4 31.8

G 13.5 15.0 17.5 23.1 28.7 35.1 46.0 58.0 70.0

* Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Lim it. ** On Request: Special threading or as for ged bolts for customer conversion.

134

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Forged Rivet Eye Bolts S-293

• Forged Steel — Quenched and Tempered. s

t

l

o

B

e

y

E

t

e

v

i

R

d

e

g

r

o

F

S-293 Rivet Eye Bolts

S-276

S-293

S-293 Stock No. 1043882 1043908 1043926 1043944 1043962 1043980 1044006 1044024 1044042 1044060 1044088 1044104 1044122 1044140 1044168 1044186 1044202 1044220 1044248

Dimensions (mm)

Weight Per 100 (kg) 2.85 5.12 5.44 8.30 11.33 12.51 14.28 19.86 28.34 42.5 51.2 65.2 73.7 108 132 170 204 327 388

A 6.35 6.35 7.94 7.94 9.53 9.53 9.53 12.7 12.7 15.9 15.9 19.1 19.1 22.2 22.2 25.4 25.4 31.8 31.8

B 51.0 102 57.0 108 63.5 114 152 82.5 152 102 152 114 152 127 203 152 229 203 305

C 67.0 118 76.0 127 86.0 137 175 111 181 140 190 159 197 178 254 213 289 279 378

D 79.5 130 92.0 143 104 155 193 136 206 171 222 196 234 222 298 263 339 340 441

E 12.7 12.7 16.0 16.0 19.1 19.1 19.1 25.4 25.4 31.8 31.8 38.1 38.1 44.5 44.5 51.0 51.0 63.0 63.0

F 25.4 25.4 31.8 31.8 38.1 38.1 38.1 51.0 51.0 63.5 63.5 76.0 76.0 89.0 89.0 102 102 127 127

G 6.35 6.35 7.87 7.87 9.65 9.65 9.65 12.7 12.7 15.8 15.8 19.1 19.1 22.2 22.2 25.4 25.4 31.8 31.8

• Forged Steel — Quenched and Tempered. s

t

l

o

B

e

y

E

t

e

v

i

R

d

e

g

r

o

F

S-276 Shoulder Rivet Eye Bolts Shank Diameter & Length (mm) 6.35 x 51.0 6.35 x 102 7.94 x 57.0 7.94 x 108 9.53 x 63.5 9.53 x 114 12.7 x 82.5 12.7 x 152 15.9 x 102 15.9 x 305 19.1 x 114 19.1 x 152 22.2 x 127 25.4 x 152 25.4 x 229 31.8 x 203 31.8 x 305 38.1 x 381

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

S-276

S-276 Stock No. 1045746 1045764 1045782 1045808 1045826 1045844 1045862 1045880 1045906 1045924 1045942 1045960 1045988 1046022 1046040 1046068 1046086 1046102

Weight Per 100 (kg) 2.49 3.18 2.86 6.71 8.53 11.3 15.0 22.7 31.2 34.0 57 68 91 135 193 297 323 646

Dimensions (mm) A 6.35 6.35 7.85 7.85 9.65 9.65 12.7 12.7 16.0 16.0 19.1 19.1 22.4 25.4 25.4 31.8 31.8 38.1

B 51.0 102 57.0 108 63.5 114 82.5 152 102 152 114 152 127 152 229 203 305 381

C 63.5 114 74.5 125 83.5 134 108 178 135 186 154 192 174 205 282 266 368 457

D 74.5 125 89.0 140 101 152 130 200 164 214 189 227 215 253 329 323 425 527

E 12.7 12.7 16.0 16.0 19.1 19.1 25.4 25.4 31.8 31.8 38.1 38.1 44.5 51.0 51.0 63.5 63.5 76.0

F 22.4 22.4 33.3 28.7 35.1 35.1 44.5 44.5 57.0 57.0 70.0 70.0 82.5 95.5 95.5 114 114 140

G 4.85 4.85 6.35 6.35 7.85 7.85 9.65 9.65 12.7 12.7 15.7 15.7 19.1 22.4 22.4 25.4 25.4 31.8

H 11.9 11.9 14.2 14.2 16.8 16.8 23.1 23.1 28.4 28.4 35.1 35.1 39.6 46.0 46.0 58.0 58.0 70.0

135

Rigging Accessories

Shank Diameter & Length (mm) 6.35 x 51.0 6.35 x 102 7.94 x 57.0 7.94 x 108 9.53 x 63.5 9.53 x 114 9.53 x 152 12.7 x 82.5 12.7 x 152 15.9 x 102 15.9 x 152 19.1 x 114 19.1 x 152 22.2 x 127 22.2 x 203 25.4 x 152 25.4 x 229 31.8 x 203 31.8 x 305

Ring Bolts - Pad Eyes G-257

• Forged Steel - Quenched and Tempered.

• Diameter of ring stock is same as shank diameter.

• Hot Dip galvanized.

• All Bolts Hot Dip galvanized after threading. s e

y E

d

a P

-

s

t l o

B

g n

i R

G-257 Shoulder Nut Ring Bolts Ring Bolt Size (m m) 9.53 X 114 12.7 X 152

-257 G

G-257 Sto ck No .

1046335 1046371

Working Lo ad Lim it (t)* .54 1.00

Dimension s (mm)

Weigh t Per 100 (kg) 25.7 45.4

A 9.65 12.7

B 63.5 76.0

C 114 152

D 195 254

E 9.70 12.7

F 35.1 44.5

G 51.0 63.5

H 16.8 23.1

* Ultimate Load is 5 times the Working Load Limit.

S-264

• Forged Steel — Quenched and Tempered.

• Forged from 1035 Carbon Steel.

• Excellent welding qualities.

• Widely used on farm machinery, trucks, steel hulled marine vessels and material handling equipment.

• Reference American Welding Society specifications for proper welding procedures. s e y

E

d a

P

-

s t

l o B

g n

i R

S-264 Pad Eyes -264 S

Size No .* *0 *1 *1 2 4 5

S-264 Stock No. 1090722 1090740 1090768 1090786 1090802 1090820

Weig ht Per 100 (kg ) 1.27 2.95 4.72 9.57 23.7 37.4

B 6.35 9.65 16.0 19.1 25.4 31.8

C 4.85 6.35 6.35 9.65 14.2 17.5

D im ensions (mm) D E 16.0 7.85 22.4 10.4 25.4 11.2 26.9 12.7 36.6 19.8 44.5 20.6

G 16.0 22.4 28.7 38.1 54.0 67.0

H 2.30 3.30 4.05 4.85 5.60 6.35

L 19.1 26.2 33.3 41.4 59.5 70.0

* Meets the requirements of Military Specification MS -51930A.

136

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Forged Eye Nuts G-400

• Forged Steel - Quenched and Tempered.

• Hot Dip galvanized.

• Tapped with standard UNC class 2 threads after galvanizing.

• Available also in blank (as forged) item (S-4028) or on request with metric threading ( M-4028) s

t u N

e

y E

d e g

r o F

G-400 Eye Nuts -40 G

G-400 Sto ck No .

1090438 1090474 1090517 1090535 1090553 1090571 1090599 1090633 1090651 1090679 1090697

Std.T Workin g Weig ht ap Load Each Size Limit (kg ) (in .) (t)* 1/4 .24 .04 3/8 .57 .08 1/2 1.02 .13 5/8 1.63 .27 3/4 2.36 .45 7/8 3.27 .75 1 4.54 1.22 1-1/4 7.03 1.76 1-3/8 8.39 2.27 1-1/2 10.21 3.08 2 18.14 6.62

Dimension s (m m) A 31.8 41.1 51.0 63.5 76.0 89.0 102 114 127 143 181

C 19.1 25.4 31.8 38.1 44.5 51.0 57.0 63.5 70.0 79.0 104

D 25.4 30.5 36.6 48.8 58.0 63.5 74.0 85.0 102 109 152

E 19.1 21.1 27.4 34.3 40.4 49.8 56.0 62.5 68.5 78.5 104

F 12.7 14.2 20.6 25.4 28.4 35.1 39.6 47.8 51.0 57.0 79.5

J 17.5 20.6 25.4 33.3 38.1 47.8 54.0 60.5 65.0 76.0 95.5

K 16.0 22.6 27.7 33.3 39.9 45.0 51.5 57.5 64.5 71.5 93.5

N 11.7 14.7 18.5 21.1 26.7 29.0 33.0 38.6 42.4 46.5 63.0

T 43.7 53 63.5 82.5 100 111 129 149 165 179 257

W 7.85 10.4 12.7 17.5 21.3 25.4 30.2 35.1 38.1 42.2 49.3

* Ultimate Load is 5 times the Working Load Limit. Rating based on standard tap size.

S-405

• Forged Steel - Quenched and Tempered.

• On request: threaded to customer specification.

• s t

u N

e y E

d e g r

o F

S-405 Lifting Eyes -405 S

Size No. 1 2 3 4 5 6 7 8 10

S-405 Sto ck No .

1090269 1090287 1090303 1090321 1090349 1090367 1090385 1090401 1090410

Wo rking L oad Weight L imit Th readed Each * A (kg) (t) .39 .05 31.8 .57 .09 41.1 1.02 .23 51.0 1.63 .36 63.5 2.36 .57 76.0 3.27 1.02 89.0 4.54 1.47 102 5.67 2.13 114 8.16 4.23 143

Dimen sio ns (mm)

C 19.1 25.4 31.8 38.1 44.5 51.0 57.0 63.5 79.0

D 25.9 30.5 36.6 48.8 58.0 63.5 74.0 85.0 97.0

E 16.8 19.1 25.4 30.2 35.1 41.4 47.8 49.3 70.0

F 12.7 14.2 20.6 25.4 28.4 35.1 39.6 47.8 57.0

H 8.65 10.4 13.5 16.8 19.8 23.1 26.2 29.5 42.2

J 17.5 20.6 28.7 33.3 38.1 47.8 54.0 60.5 76.0

K 17.0 23.4 28.7 35.1 42.2 48.5 55.0 62.5 75.5

L 17.5 23.9 31.8 38.1 44.5 47.8 52.5 63.5 81.5

N 10.7 14.0 17.3 20.3 24.9 26.9 30.5 35.6 42.9

T 62.5 76 93.5 116 140 156 179 207 252

W 7.85 10.4 12.7 17.5 21.3 25.4 30.2 35.1 42.2

* Ultimate Load is 5 times the Working Load Limit. Rating based on UNC thread size shown in column "H".

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

137

Rigging Accessories

"S" Stock Size Size No. (mm) 1 6.35 2 7.85 3A 9.65 4 12.7 5 16 6 19.1 7 22.4 8 25.4 9 28.7 10 31.8 11 38.1

Swivel Hoist Ring Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.

U.S. Patent 5,352,056

HR-125 M Patented

HR-125 Patented

• Rated at 100% at 90° angle • Each product has a Product Identification Code (PIC) for material • • • • • •

• • •

• •

138

traceability along with a Working Load Limit and the name Crosby or “CG” stamped into it.

All components are Alloy Steel - Quenched and Tempered.

Available in UNC and Metric thread sizes.

UNC threads available in sizes from 800 pounds to 30,000 pounds Working Load Limit, with a design factor of 5 to 1.

Metric threads available in sizes from 400 kg to 16,900 kg and dual rated in both a 4 to 1 and 5 to 1 design factor.

360° swivel and 180° pivot action.

100% individually proof tested to 2-1/2 times the Working Load Limit with certification and Statistically Magnetic Particle inspected. (Can be furnished 100% Magnetic Particle inspected when requested at time of order).

Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit.

Individually packaged along with proper application instructions and warning information.

Bolt is secured with patented retaining ring which requires no modification to threads. This method allows for easy disassembly and assembly of hoist ring for thorough examination of all components. Replacement kits are available.

Bolts are individually Proof Tested.

Multiple Bolt lengths available to meet specific application requirements.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

UNC Swivel Hoist Rings SEE APPLICATION AND WARNING INFORMATION Pa ra Esp añ o l: ww w .th ec ros by gro u p.co m

+R-125

On Pages 156-157

• Top washer has the following features: • The Working Load Limit and Recommended Torque value are permanently stamped into each washer.

• Washer is color coded for easy identification: Red - UNC thread.

• Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A 574. All threads listed are UNC. • BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing below.

Illustration shows meaning of each dimension given.

• NOTE: For Special Applications, see page 334. i R

t s

i o H

l

e v i wS

CNU

Rigging Accessories

s g n

HR-125 UNC Threads Dimension s (in .)

F rame Size No .

1† 1† 2 2† 2 2† 2 2† 3 3† 3 3† 3 3† 4 5 5 6 7 8

-125 R H

HR-125 Stock No. 1016887 1016898 1016909 1016912 1016920 1016924 1016931 1016935 1016942 1016946 1016953 1016957 1016964 1016969 1016975 1016986 1016997 1017001 1017005 1017009

Working Load Limit (lbs.)* 800 1000 2500 2500 4000 4000 5000 5000 7000 7000 8000 8000 10000 10000 15000 24000 30000 50000 75000 100000

Torque in Ft. Lbs. 7 12 28 28 60 60 100 100 100 100 160 160 230 230 470 800 1100 2100 4300 6600

Bolt Size A‡ 5/16 - 18 x 1.50 3/8 - 16 x 1.50 1/2 - 13 x 2.00 1/2 - 13 x 2.50 5/8 - 11 x 2.00 5/8 - 11 x 2.75 3/4 - 10 x 2.25 3/4 - 10 x 2.75 3/4 - 10 x 2.75 3/4 - 10 x 3.50 7/8 - 9 x 2.75 7/8 - 9 x 3.50 1 - 8 x 3.00 1 - 8 x 4.00 1-1/4 - 7 x 4.50 1-1/2 - 6 x 6.50 2 - 4-1/2 x 6.50 2-1/2 - 4 x 8.00 3 - 4 x 10.50 3-1/2 - 4 x 13.00

Effective T hread Projectio n L en gth B .59 .59 .71 1.21 .71 1.46 .96 1.46 .90 1.65 .90 1.65 1.15 2.15 2.22 2.98 2.98 4.00 5.20 7.00

C 2.69 2.69 4.82 4.82 4.82 4.82 4.82 4.82 6.55 6.55 6.55 6.55 6.55 6.55 8.70 12.39 12.39 16.88 19.50 22.06

D .94 .94 2.00 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00 3.00 3.00 3.75 4.75 4.75 5.75 7.25 7.75

Rad ius E .46 .46 .88 .88 .88 .88 .88 .88 1.37 1.37 1.37 1.37 1.37 1.37 1.69 2.25 2.25 3.00 3.75 4.00

Diameter F .34 .34 .69 .69 .69 .69 .69 .69 .94 .94 .94 .94 .94 .94 1.19 1.69 1.69 2.25 2.75 3.25

G 1.69 1.69 3.30 3.30 3.30 3.30 3.30 3.30 4.73 4.73 4.73 4.73 4.73 4.73 6.00 8.00 8.00 11.69 14.12 16.00

H 1.11 1.09 2.29 2.29 2.21 2.21 2.05 2.05 2.98 2.98 2.85 2.85 2.73 2.73 3.92 5.94 5.14 8.00 8.50 9.25

Weigh t Each (lb s.) .43 .43 2.49 2.52 2.55 2.70 2.65 3.00 7.00 7.00 7.00 7.00 7.50 7.50 14.79 33.00 36.00 88.00 165.00 240.00

* Ultimate Load is 5 times the Wor king Load Limit. † Long Bolts are designed to be used with soft metal (i.e., aluminum) work piece. While the long bolts may also be used with ferr ous metal (i.e.,steel & iron) work piece, short bolts ar e designed for ferr ous work pieces only. ‡ Bolt specification is a Grade 8 Alloy socket head cap screw to AS TM A 574.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

139

Metric Swivel Hoist Rings SEE APPLICATION AND WARNING INFORMATION Pa ra Esp añ o l: ww w .th e cro sby gro u p.co m

+R-125M

On Pages 156-157

• Top washer has the following features: • The Working Load Limit and Recommended Torque value are permanently stamped into each washer.

• Washer is color coded for easy identification: Silver - Metric thread.

• Bolt specification is a Grade 12.9 Alloy socket head cap screw to Din 912. All threads listed are metric (ASME/ANSI B18.3.1m).

• Designed to be used with ferrous work piece only.

• BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing below.

Illustration shows meaning of each dimension given.

• NOTE: For Special Applications, see page 334. s g

n i R

t s

i o H

l e

v i wS

c i

r t e M

HR-125M Metric Threads Workin g L oad Limit (kg)

-125M R H

HR-125M Stock No. 1016602 1016613 1016624 1016635 1016644 1016657 1016668 1016679 1016690 1016701 1016712

At a 5:1 Desig n Factor † 400 450 1050 1900 2150 3000 4200 7000 11000 12500 13500

At a 4:1 Design Factor † 500 550 1300 2400 2700 3750 5250 8750 13750 15600 16900

Dimensio ns (mm)

Torqu e in Nm* 10 16 38 81 136 136 312 637 1005 1005 1350

(A) Bo lt Size‡ M8X1.25X40 M10X1.50X40 M12X1.75X50 M16X2.00X60 M20X2.50X65 M20X2.50X75 M24X3.00X80 M30X3.50X120 M36X4.00X150 M42X4.50X160 M48X5.00X160

(B) Effective Thread Pro jection Length 16.9 16.9 17.2 27.2 31.2 28.1 33.1 65.1 60.6 70.6 70.6

C 68.1 68.1 124.5 124.5 124.5 167.0 167.0 231.5 315.3 315.3 315.3

D 25.4 25.4 50.8 50.8 50.8 76.2 76.2 95.3 120.7 120.7 120.7

Radius E 11.8 11.8 22.3 22.3 22.3 34.7 34.7 44.5 57.2 57.2 57.2

Dia. F 8.5 8.5 17.5 17.5 17.5 25.4 25.4 30.5 44.5 44.5 44.5

G 42.9 42.9 82.7 82.7 82.7 120.1 120.1 152.4 203.2 203.2 203.2

H 28.2 27.69 58.17 56.13 52.07 75.69 74.93 69.34 124.20 150.62 137.92

Weigh t Each (kg) .19 .19 1.13 1.22 1.36 3.18 3.18 6.70 14.95 16.33 16.33

* The tightening torque values shown are based upon threads being clean, dr y and free of lubrication. † Individually proof loaded to 2-1/2 times the Working Load Limit based on the 4:1 design factor. ‡ Bolt specification is a Grade 12.9 Alloy socket head cap screw to Din 912. All threads are metric (ASME/ANSI B18.3.1m).

140

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

HR-1200 Side Pull Hoist Rings SEE APPLICATION AND WARNING INFORMATION On Pages 158-159

HR-1200 • Wide range of capacities available: UNC AND METRIC • 650 lbs. to 29,000 lbs.

-120M R H

• Metric sizes from 0.3 tonnes to 13 tonnes.

• Rated at 100% of Working Load Limit for angles up to 90 degrees.

• Utilize standard Crosby Red Pin® Shackles to connect to wire rope or synthetic slings. (sold separately) • Multiple bolt lengths available to meet specific application requirements.

• Hoist Ring body is furnished with Yellow Chromate finish for improved corrosion resistance.

• Each product is stamped with a Product Identification Code (PIC), for material traceability, along with a Working Load Limit, and the name Crosby or "CG".

• Body components are Alloy Steel - Quenched and Tempered. i R

t s

i o H

l

l u P

e d

i S

0 0

2 1 - RH

HR-1200 UNC Sidepull Hoist Rings Dimensions (in .)

Wo rkin g Weig ht L oad Each L imit (lbs.) (lb s.) * .35 650 .36 800 1.4 2000 1.4 2000 1.5 3000 1.5 3000 4.5 5000 4.6 5000 4.6 6500 4.8 6500 4.8 8000 5.0 8000 10.2 14000 23.5 17200 25.3 29000

Hoist (B) Ring Eff. (A) Bolt Th read HR-1200 Torque Bolt Pro j.

C D Stock No. (Ft.Lbs.) Size (in.)

1067700 7 5/16-18x1.50 .59 1.93 .72 1067704 12 3/8-16x1.50 .59 1.93 .72 1067708 28 1/2-13x2.00 .71 2.97 .97 1067712 28 1/2-13x2.50 1.21 2.97 .97 1067716 60 5/8-11x2.00 .71 2.97 .97 1067720 60 5/8-11x2.75 1.46 2.97 .97 1067724 100 3/4-10x2.75 .90 4.32 1.34 1067728 100 3/4-10x3.50 1.65 4.32 1.34 1067732 160 7/8-9x2.75 .90 4.32 1.34 1067736 160 7/8-9x3.50 1.65 4.32 1.34 1067740 230 1 -8x3.00 1.15 4.32 1.34 1067744 230 1 -8x4.00 2.15 4.32 1.34 1067748 470 1-1/4-7x4.5 2.22 5.59 1.57 1067756 800 1-1/2-6x6.5 2.98 7.31 2.06 1067764 1100 2 -4.5x6.5 2.98 7.31 2.06

I 1.43 1.43 1.79 1.79 1.79 1.79 2.42 2.42 2.42 2.42 2.42 2.42 3.42 4.29 4.29

Recommend ed Sh ackles Red Pin® Shackles Red Pin 209,210,213, Web Shackles 215,2130,2150 S-281 Nomin al Web WLL WLL Size Size (t) (tons) (in.) (in.)

1/2, 5/8 2, 3-1/4 2 3-1/4 1/2, 5/8 2, 3-1/4 2 3-1/4 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 1, 1-1/8, 1-1/4 8-1/2, 9-1/2, 12 3 8-1/2 1-3/8, 1-1/2, 1-3/4 13-1/2, 17, 25 1-3/8, 1-1/2, 1-3/4 13-1/2, 17, 25 -

I 36.3 36.3 45.5 45.5 61.5 61.5 86.9 109 109 109

Recommend ed Sh ackles Red Pin® Shackles Red Pin ® Web 209,210,213, Shackles 215,2130,2150 S-281 Nomin al Web WLL WLL Size Size (t) (tons) (in.) (in.)

1/2, 5/8 2, 3-1/4 2 3-1/4 1/2, 5/8 2, 3-1/4 2 3-1/4 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 5/8, 3/4 3-1/4, 4-3/4 2, 1.5 3-1/4, 4-1/2 7/8 6-1/2 2 6-1/4 7/8 6-1/2 2 6-1/4 1, 1-1/8,1-1/4 8-1/2, 9-1/2, 12 3 8-1/2 1-3/8, 1-1/2,1-3/4 13-1/2, 17, 25 1-3/8, 1-1/2,1-3/4 13-1/2, 17, 25 1-3/8, 1-1/2,1-3/4 13-1/2, 17, 25 -

-1200 R H

-120X R H

E 1.00 1.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00 3.00 3.00 3.75 4.75 4.75

F 1.56 1.56 2.13 2.13 2.13 2.13 3.00 3.00 3.00 3.00 3.00 3.00 3.91 5.19 5.19

G .80 .80 .93 .93 .93 .93 1.07 1.07 1.07 1.07 1.07 1.07 1.47 2.11 2.11

H .85 .85 1.07 1.07 1.07 1.07 1.35 1.35 1.35 1.35 1.35 1.35 1.92 2.41 2.41

HR-1200M Metric Sidepull Hoist Rings Dimensions (mm )

Wo rkin g Weig ht L oad Each L imit (kg ) (kg)* .18 300 .18 400 .63 1000 .68 1400 2.0 2250 2.2 3500 4.5 6250 10.4 7750 10.7 10000 11.0 13000

Hoist Ring Bolt HR1200M Torque Stock No. (Nm) 1067803 10 1067807 16 1067811 38 1067815 81 1067823 136 1067827 312 1067831 637 1067835 1005 1067839 1005 1067843 1350 -120M R H

-120MX R H

(A) Bolt Size M8x1.25x40 M10x1.50x40 M12x1.75x50 M16x2.0x60 M20x2.5x75 M24x3.0x80 M30x3.5x120 M36x4.0x150 M42x4.5x160 M48x5.0x160

(B) Eff. Th read Pro j. (mm) 16.9 16.9 17.2 27.2 28.1 33.1 65.1 60.6 70.6 70.6

C 49.0 49.0 75.4 75.4 110 110 142 186 186 186

D 18.3 18.3 24.6 24.6 34.0 34.0 39.9 52.3 52.3 52.3

E 25.4 25.4 50.8 50.8 76.2 76.2 95.3 121 121 121

F 39.6 39.6 54.1 54.1 76.2 76.2 99.3 132 132 132

G 20.3 20.3 23.6 23.6 27.2 27.2 37.3 53.6 53.6 53.6

H 21.6 21.6 27.2 27.2 34.4 34.4 48.8 61.2 61.2 61.2

* Ultimate Load is 5 times the Wor king Load Limit.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

141

Rigging Accessories

s g n

Hoist Ring to Chain or Webbing SEE APPLICATION AND WARNING INFORMATION On Pages 156-157

HR-125C

• Available in capacities from 2 to 8.2 tonnes.

• Fits Grade 8 Chain size 7, 8, 10, 13 and 16mm.

• Full 360 degrees swivel and 180 degrees pivot action.

• "Yellow Chromate" finish for increased corrosion protection.

• Design factor of 4 to 1.

• Individually Proof Tested to 2-1/2 times Working Load Limit.

• Forged Alloy Steel.

• Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A574. All threads are UNC. g n i

b b e W

r o

n

i a h C

o t

g n i

R

t s

i o H

HR-125C Hoist Ring to Chain R-125C H

HR-125C Stock No. 1067492 1067494 1067500 1067502 1067509 1067511 1067518

Working Lo ad Limit (t) * 2 2 †† 3.2 3.2 †† 5.4 5.4 †† 8.2

T orque in Ft.-L bs.

60 60 100 100 230 230 470

Effective Thread Projection Length (mm ) 18.0 37.1 22.9 41.9 29.2 54.6 56.4

Dim en sion (mm) Spectru m 8 Chain Size (in. - mm) 1/4-5/16 7-8 1/4-5/16 7-8 3/8 10 3/8 10 1/2 13 1/2 13 5/8 16

UNC Th read A 5/8-11 x 2.00 5/8-11 x 2.00 3/4-10 x 2.75 3/4-10 x 3.50 1-8 x 3.00 1-8 x 4.00 1-1/4-7 x 4.50

B 17.8 30.5 22.6 41.7 29.0 54.5 56.0

D 49.8 49.8 75.0 75.0 75.0 75.0 94.0

E 90.0 90.0 121 121 122 122 166

G 85.0 85.0 124 124 124 124 157

Weigh t Each (kg ) .95 .95 2.45 2.45 2.90 3.04 5.81

* Ultimate load is 4 times the Working Load Limit. Individually tested to 2-1/2 the Working Load Limit. † † Long Bolts are designed to be used with soft metal (i.e., aluminum) work piece. While the long bolts may also be used with fer rous metal (i.e., steel & ir on).

HR-125W

• Available in capacities from 2.95 to 5.67t.

• Fits webbing sizes 50 to 100mm.

• Design Factor of 5 to 1.

• Forged Alloy Steel • Durable plastic cover protects the sling at the eye as well as keeps the sling positioned correctly on the spool.

• Designed for use with Type III (Eye & Eye), class 7, 2 ply webbing & synthetic round slings. Also accommodates single ply endless slings.

• Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A574. All threads are UNC. g n i b

b e W

r

o

n

i a h C

o t

g n i R

t s i

o H

HR-125W Hoist Ring to Web Roun d HR-125W Sling Web Eye Stock Size Width Wid th No. (No .) (mm) (mm ) 1067610 1 & 2 50 50 1067615 1 & 2 50 50 1067629 3 75 35 1067634 3 75 35 1067638 4 100 50 -125W R H

Wo rkEff. in g Th read L oad T orque Proj. in L im it Leng th Ft.-lbs. (m m) (t)* 2.95 100 22.9 2.95 100 41.9 4.08 230 29.2 4.08 230 54.6 5.67 470 56.4

Spoo l Dimension bolt (m m) & nu t To rq ue in Ft.A B C D E Lbs. 90 3/4-10x2.75 22.6 54.0 75.0 121 90 3/4-10x3.50 41.7 54.0 75.0 121 110 1-8x3.00 29.0 41.4 75.0 121 110 1-8x4.00 54.5 41.4 75.0 121 130 1-1/4-7x4.5 56.0 54.0 94.0 158

F 121 121 115 115 109

G 124 124 124 124 157

Weig ht Each (kg ) 2.81 2.86 3.22 3.31 6.21

* Ultimate load is 5 times the Working Load Limit. Individually tested to 2-1/2 times the Working Load Limit. † † Long Bolts are designed to be used with soft metal (i.e.,aluminum) work piece.While the long bolts may also be used with ferr ous metal (i.e.,steel & ir on).

142

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Crosby® Turnbuckles

HG-223 Hook & Hook

HG-225 Hook & Eye

HG-226 Eye & Eye

HG-227 Jaw & Eye

HG-228 Jaw & Jaw

Meets the performance requirements of Federal Specifications FF-T791b, Type 1, Form 1 — Class 5, and ASTM F-1145, except for those provisions required of the contractor.

Meets the performance requirements of Federal Specifications FF-T791b, Type 1, Form 1 — Class 6, and ASTM F-1145, except for those provisions required of the contractor.

Meets the performance requirements of Federal Specifications FF-T791b, Type 1, Form 1 — Class 4, and ASTM F-1145, except for those provisions required of the contractor.

Meets the performance requirements of Federal Specifications FF-T791b, Type 1, Form 1 — Class 8, and ASTM F-1145, except for those provisions required of the contractor.

Meets the performance requirements of Federal Specifications FF-T791b, Type 1, Form 1 — Class 7, and ASTM F-1145, except for those provisions required of the contractor.

• Hot Dip galvanized.

• End fittings are Quenched and Tempered, bodies heat treated by normalizing.

• Hooks are forged with a greater cross sectional area that results in a stronger hook with better fatigue properties.

• Modified UNJ thread on end fittings for improved fatigue properties. Body has UNC threads.

• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 1/4" through 2-1/2", a shackle one size smaller can be reeved through eye.

• Forged jaw ends are fitted with bolts and nuts on sizes 1/4" through 5/8",

Modified thread: Note stress relieving radii in this unretouched photo enlargement of the supabuckle.

and pins and cotters on sizes 3/4" through 2-3/4".

• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY. • Lock Nuts available for all sizes.

• Crosby’s Quenched and Tempered end fittings and normalized bodies have enhanced impact properties for greater toughness at all temperatures.

• Typical hardness levels, Tensile Strengths and Ductility Properties are available for all sizes.

• Turnbuckles can be furnished proof tested or magnaflux inspected with certificates if requested at time of order.

• Turnbuckle assembly combinations include: Eye and Eye, Hook and Hook, Hook

Standard thread: Note stress building sharp “V” in this unretouched photo enlargement.

and Eye, Jaw and Jaw, Jaw and Eye.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

143

Hook & Hook Turnbuckles HG-223

• Hot Dip galvanized steel.

• End fittings are Quenched and Tempered, bodies heat treated by normalizing.

• Hooks are forged with a greater cross sectional area that results in a stronger hook with better fatigue properties.

• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULLS ONLY. • Modified UNJ thread on end fittings for improved fatigue properties.

• Body has UNC threads.

• Lock Nuts available for all sizes (see page 153).

• Comprehensive end fitting data provided on page 149.

• Fatigue Rated. s

e

l

k

c

u

b

n

r

u

T

k

o

o

H

&

k

o

o

H

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1 Form 1 - CLASS 5, except for those provisions required of the contractor.

HG-223 Hook & Hook Thread Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 12 5/8 x 6 5/8 x 12 3/4 x 6 3/4 x 12 3/4 x 18 7/8 x 12 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24

Thread Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 305 15.9 x 305 15.9 x 305 19.1 x 152 19.1 x 305 19.1 x 457 22.2 x 305 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610

HG2 3

HG-223 Stock No. 1030011 1030039 1030057 1030075 1030119 1030137 1030173 1030191 1030235 1030253 1030271 1030333 1030351 1030379 1030397 1030413 1030431 1030459 1030477 1030495

Working Load Limit (t)* .18 .32 .45 .68 .68 1.02 1.02 1.36 1.36 1.36 1.81 2.27 2.27 2.27 2.95 2.95 2.95 3.40 3.40 3.40

Weight Each (kg) .14 .21 .35 .73 1.03 1.25 1.59 1.76 2.46 3.68 3.67 5.41 6.35 7.82 9.33 10.4 12.2 12.5 14.1 17.0

A 6.35 7.85 9.65 12.7 12.7 16.0 16.0 19.1 19.1 19.1 22.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1

D 11.4 12.7 14.2 16.8 16.8 22.9 22.9 24.9 24.9 24.9 28.7 31.8 31.8 31.8 38.1 38.1 38.1 47.8 47.8 47.8

E Closed 40.4 49.3 58.5 74.5 74.5 93.5 93.5 115 115 115 132 148 148 148 183 183 183 212 212 212

F 32.3 38.1 45.0 58.0 58.0 71.5 71.5 84.5 84.5 84.5 96.0 108 108 108 130 130 130 146 146 146

Dimensions (mm) J K Open Closed 282 181 325 211 419 267 478 300 783 453 521 337 826 489 568 378 873 530 1178 683 914 565 956 600 1261 753 1565 905 1027 659 1332 811 1637 964 1116 735 1421 887 1726 1040

M Open 303 351 450 518 822 572 876 629 934 1239 984 1034 1338 1643 1119 1424 1729 1205 1510 1815

N Closed 202 236 298 340 492 387 540 439 591 744 635 678 830 983 751 903 1056 824 976 1129

BB 101 114 152 152 304 152 304 152 304 457 304 304 457 609 304 457 609 304 457 609

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

144

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Hook & Eye Turnbuckles HG-225

• Hot Dip galvanized steel.

• End fittings are Quenched and Tempered, bodies heat treated by normalizing.

• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckles sizes 6 mm through 64 mm, a shackle one size smaller can be reeved through eye.

• Turnbuckle hooks are forged with a greater cross sectional area that results in a stronger hook with better fatigue properties.

• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY. • Modified UNJ thread on end fittings for improved fatigue properties.

• Body has UNC threads.

• Lock Nuts available for all sizes (see page 153).

• Comprehensive end fitting data provided on pages 149 & 150.

• Fatigue Rated. e

l

k

c

u

b

n

r

u

T

e

y

E

&

k

o

o

H

Rigging Accessories

s

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1, Form 1 — CLASS 6, except for those provisions required of the contractor.

HG-225 Hook & Eye Thread Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 12 5/8 x 6 5/8 x 12 3/4 x 6 3/4 x 12 3/4 x 18 7/8 x 12 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24

Thread Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 305 15.9 x 152 15.9 x 305 19.1 x 152 19.1 x 305 19.1 x 457 22.2 x 305 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610

HG2 5

HG-225 Stock No. 1030636 1030654 1030672 1030690 1030734 1030752 1030798 1030814 1030850 1030878 1030896 1030958 1030976 1030994 1031010 1031038 1031056 1031074 1031092 1031118

Working Load Weight Each Limit * (kg) (t) .18 .13 .32 .22 .45 .35 .68 .73 .68 1.03 1.02 1.22 1.02 1.71 1.36 1.76 1.36 2.64 1.36 2.87 1.81 3.67 2.27 5.41 2.27 6.35 2.27 7.82 2.95 8.62 2.95 10.4 2.95 10.9 3.40 12.5 3.40 14.1 3.40 17.0

A 6.35 7.94 9.53 12.7 12.7 15.9 15.9 19.1 19.1 19.1 22.2 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1

D 11.4 12.7 14.2 16.8 16.8 21.3 21.3 24.9 24.9 24.9 28.7 31.8 31.8 31.8 38.1 38.1 38.1 47.8 47.8 47.8

E Closed 40.4 49.3 58.0 74.5 74.5 93.5 93.5 115 115 115 132 148 148 148 183 183 183 212 212 212

F 32.3 38.1 45.0 58.0 58.0 71.0 71.0 85.0 84.5 84.5 96.0 108 108 108 130 130 130 146 146 146

J Open 291 335 431 494 798 557 844 587 892 1197 927 985 1290 1595 1057 1362 1667 1136 1441 1745

Dimensions (mm) K M Closed Open 189 307 221 342 279 456 316 525 469 829 355 577 507 882 397 634 549 939 702 1243 579 982 630 1046 782 1351 935 1656 689 1132 842 1437 994 1741 755 1212 907 1517 1060 1822

N Closed 205 241 303 347 500 393 545 443 596 748 633 691 843 996 764 916 1068 831 983 1136

R 19.8 23.9 28.5 36.6 36.6 44.5 44.5 53.0 53.0 53.0 60.0 76.0 76.0 76.0 90.0 90.0 90.0 103 103 103

S 8.64 11.2 13.5 18.3 18.3 22.2 22.2 25.4 25.4 25.4 31.8 36.6 36.6 36.6 46.0 46.0 46.0 54.0 54.0 54.0

X Closed 44.5 53.0 64.0 82.0 82.0 99.0 99.0 119 119 119 130 162 162 162 196 196 196 219 219 219

BB 102 114 152 152 305 152 305 152 305 457 305 305 457 610 305 457 610 305 457 610

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

145

Eye & Eye Turnbuckles HG-226

• Hot Dip galvanized steel.

• End fittings are Quenched and Tempered, bodies heat treated by normalizing.

• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 1/4" through 2-1/2", a shackle one size smaller can be reeved through eye.

• Modified UNJ thread on end fittings for improved fatigue properties. Body has UNC threads.

• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY. • Lock Nuts available for all sizes (see page 153).

• Comprehensive end fitting data provided on page 150.

• Fatigue Rated. s

e

l

k

c

u

b

n

r

u

T

e

y

E

&

e

y

E

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1, Form 1 - CLASS 4, except for those provisions required of the contractor.

HG-226 Eye & Eye Thread Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 12 5/8 x 6 5/8 x 12 3/4 x 6 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

Thread Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 305 15.9 x 152 15.9 x 305 19.1 x 152 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

HG2 6

HG-226 Stock No. 1031252 1031270 1031298 1031314 1031350 1031378 1031412 1031430 1031476 1031494 1031519 1031537 1031555 1031573 1031591 1031617 1031635 1031653 1031671 1031699 1031715 1031733 1031779 1031797 1031813 1031831 1031859

Working Load Limit (t)* .23 .36 .54 1.00 1.00 1.59 1.59 2.36 2.36 2.36 3.27 3.27 4.54 4.54 4.54 4.54 6.89 6.89 6.89 9.71 9.71 9.71 12.7 12.7 16.8 27.2 34.0

Weight Each (kg) .12 .20 .34 .70 .97 1.49 1.55 1.72 2.49 3.26 3.27 4.51 4.10 5.22 6.35 7.82 8.62 10.4 12.2 12.5 14.1 17.0 23.8 26.3 38.7 65 88

A 6.35 7.85 9.65 12.7 12.7 16.0 16.0 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 63.5 70.0

J Open 300 344 444 510 815 557 862 607 911 1216 942 1246 710 1015 1320 1625 1087 1392 1697 1156 1461 1765 1457 1762 1923 1997 2057

K Closed 198 230 291 332 485 373 525 416 568 721 592 745 507 660 812 964 719 871 1024 775 927 1080 1000 1153 1313 1387 1448

M Open 311 359 461 532 837 582 887 638 943 1248 980 1284 755 1066 1364 1669 1145 1449 1754 1219 1524 1829 1534 1838 2011 2099 2172

Dimensions (mm) N Closed 210 244 309 355 507 398 551 448 600 752 630 783 552 704 856 1009 776 929 1081 838 991 1143 1076 1229 1402 1489 1562

R 19.8 23.8 28.4 36.5 36.5 44.4 44.4 53.0 53.0 53.0 60.4 60.4 76.0 76.0 76.0 76.0 90.5 90.5 90.5 103 103 103 117 117 146 165 177

S 8.65 11.1 13.4 18.2 18.2 22.3 22.3 25.4 25.4 25.4 31.7 31.7 36.5 36.5 36.5 36.5 46.0 46.0 46.0 54.0 54.0 54.0 60.4 60.4 68.5 79.0 82.5

X Closed 44.5 53.0 64.0 82.0 82.0 99.0 99.0 119 119 119 130 130 162 162 162 162 196 196 196 219 219 219 254 254 333 350 387

BB 101 114 152 152 304 152 304 152 304 457 304 457 152 304 457 609 304 457 609 304 457 609 457 609 609 609 609

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

146

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Jaw & Eye Turnbuckles HG-227

• Hot Dip galvanized steel.

• End fittings are Quenched and Tempered, bodies heat treated by normalizing.

• Turnbuckles eyes are forged and elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckles size 6 mm through 64 mm, a shackle one size smaller can be reeved through eye.

• Forged jaw ends are fitted with bolts and nuts for 6 mm through 16 mm, and pins and cotters on 19 mm through 70 mm sizes.

• Modified UNJ thread on end fittings for improved fatigue properties.

• Body has UNC threads.

• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY. • Lock Nuts available for all sizes (see page 153).

• Comprehensive End fitting data on pages 150 & 151.

• Fatigue Rated. s

e

l

k

c

u

b

n

r

u

T

e

y

E

&

w

a

J

Rigging Accessories

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1, Form 1 - CLASS 8, except for those provisions required of the contractor.

HG-227 Jaw & Eye Thread Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

Thread Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

HG2 7

HG-227 Stock No. 1031877 1031895 1031911 1031939 1031957 1031975 1031993 1032019 1032037 1032055 1032073 1032091 1032117 1032135 1032153 1032171 1032199 1032215 1032233 1032251 1032279 1032297 1032313 1032331 1032359 1032395 1032411 1032439 1032457 1032475

Working Load Weight Limit Each * (t) (kg) .23 .14 .36 .23 .54 .36 1.00 .68 1.00 .78 1.00 .94 1.59 1.07 1.59 1.44 1.59 1.64 2.36 1.81 2.36 2.15 2.36 2.69 2.36 3.18 3.27 3.79 3.27 4.42 4.54 4.05 4.54 5.08 4.54 6.03 4.54 7.71 6.89 8.81 6.89 11.0 6.89 12.9 9.71 13.1 9.71 15.9 9.71 17.8 12.7 24.4 12.7 27.5 16.8 40.4 27.2 68 34.0 83

A 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 63.5 70.0

B 11.4 12.7 13.7 16.5 16.5 16.5 20.1 20.1 20.1 23.9 23.9 23.9 23.9 28.7 28.7 34.0 34.0 34.0 34.0 44.5 44.5 44.5 52.3 52.3 52.3 66.0 66.0 66.5 76.5 92.2

E Closed 40.1 50.5 54.0 70.0 70.0 70.0 89.0 89.0 89.0 106 106 106 106 123 123 140 140 140 140 183 183 183 200 200 200 239 239 301 344 387

G 15.7 22.1 22.1 26.9 26.9 26.9 33.3 33.3 33.3 38.1 38.1 38.1 38.1 44.5 44.5 52.5 52.5 52.5 52.5 71.5 71.5 71.5 71.5 71.5 71.5 86.0 86.0 93.5 113 106

J Open 288 348 427 490 642 795 533 686 838 576 729 881 1186 917 1221 669 974 1279 1583 1050 1354 1659 1105 1410 1715 1407 1711 1845 1925 1978

Dimensions (mm) K M Closed Open 187 307 221 356 275 451 312 520 388 673 465 825 349 572 425 725 501 877 386 625 462 777 538 930 691 1235 567 973 720 1278 466 734 618 1039 771 1343 923 1648 681 1132 834 1424 986 1741 724 1200 876 1505 1029 1810 949 1518 1102 1823 1235 1980 1316 2093 1369 2172

N Closed 205 242 299 342 419 495 388 464 541 435 511 587 739 624 776 531 683 835 988 763 916 1068 819 972 1124 1061 1214 1370 1483 1562

R 19.8 23.8 28.4 36.5 36.5 36.5 44.4 44.4 44.4 53.0 53.0 53.0 53.0 60.4 60.4 76.0 76.0 76.0 76.0 90.5 90.5 90.5 103 103 103 117 117 146 165 177

S 8.65 11.1 13.4 18.2 18.2 18.2 22.3 22.3 22.3 25.4 25.4 25.4 25.4 31.7 31.7 36.5 36.5 36.5 36.5 46.0 46.0 46.0 54.0 54.0 54.0 60.4 60.4 68.3 79.0 82.5

X Closed 44.5 53.0 64.0 82.0 82.0 82.0 99.0 99.0 99.0 119 119 119 119 130 130 162 162 162 162 196 196 196 219 219 219 254 254 332 350 387

BB 101 114 152 152 228 304 152 228 304 152 228 304 457 304 457 152 304 457 609 304 457 609 304 457 609 457 609 609 609 609

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

147

Jaw & Jaw Turnbuckles HG-228

• • • • • • • • •

Hot Dip galvanized steel.

End fittings are Quenched and Tempered, bodies heat treated by normalizing.

TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY. Forged jaw ends are fitted with bolts and nuts for 6 mm through 64 mm, and pins and cotters on 19 mm through 70 mm sizes.

Modified UNJ thread on end fittings for improved fatigue properties.

Body has UNC threads.

Lock Nuts available for all sizes (see page 153).

Comprehensive end fitting data provided on page 151.

Fatigue Rated. s

e

l

k

c

u

b

n

r

u

T

w

a

J

&

w

a

J

Meets the performance requirements of Federal Specifications FF-T791b,Type 1, Form 1 - CLASS 7, except for those provisions required of the contractor.

HG-228 Jaw & Jaw Thread Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

Thread Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

HG2 8

HG-228 Stock No. 1032493 1032518 1032536 1032554 1032572 1032590 1032616 1032634 1032652 1032670 1032698 1032714 1032732 1032750 1032778 1032796 1032812 1032830 1032858 1032876 1032894 1032910 1032938 1032956 1032974 1033018 1033036 1033054 1033072 1033090

Working Load Limit (t)* .23 .36 .54 1.00 1.00 1.00 1.59 1.59 1.59 2.36 2.36 2.36 2.36 3.27 3.27 4.54 4.54 4.54 4.54 6.89 6.89 6.89 9.71 9.71 9.71 12.7 12.7 16.8 27.2 34.0

Weight Each (kg) .16 .24 .37 .71 .79 1.09 1.23 1.56 1.77 1.86 2.48 2.98 3.64 3.71 4.89 4.62 5.53 6.87 8.20 9.34 11.2 12.8 13.9 16.7 18.9 24.5 28.7 42.8 75 90

A 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 63.5 70.0

B 11.4 12.7 13.7 16.5 16.5 16.5 20.1 20.1 20.1 23.9 23.9 23.9 23.9 28.7 28.7 34.0 34.0 34.0 34.0 44.5 44.5 44.5 52.3 52.3 52.3 66.0 66.0 66.5 76.5 92.2

E Closed 40.1 50.5 54.0 70.0 70.0 70.0 89.0 89.0 89.0 106 106 106 106 123 123 140 140 140 140 183 183 183 200 200 200 239 239 301 344 387

G 15.7 22.1 22.1 26.9 26.9 26.9 33.3 33.3 33.3 38.1 38.1 38.1 38.1 44.5 44.5 52.5 52.5 52.5 52.5 71.5 71.5 71.5 71.5 71.5 71.5 86.0 86.0 93.5 113 106

Dimensions (mm) J K Open Closed 277 175 314 212 410 258 470 292 622 368 775 445 509 325 662 401 814 478 546 356 699 432 851 508 1156 660 892 543 1197 695 628 425 933 577 1237 729 1542 882 1012 644 1317 796 1622 948 1054 673 1359 826 1664 978 1356 899 1661 1051 1766 1157 1854 1244 1899 1289

M Open 302 353 441 508 660 813 562 715 867 612 765 917 1222 967 1272 713 1018 1322 1627 1119 1423 1728 1181 1486 1791 1503 1808 1949 2087 2172

N Closed 201 239 289 330 406 483 378 454 530 422 498 574 726 618 770 510 662 814 967 750 903 1055 800 953 1105 1046 1198 1339 1478 1562

BB 102 114 152 152 229 305 152 229 305 152 229 305 457 305 457 152 305 457 610 305 457 610 305 457 610 457 610 610 610 610

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

148

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Turnbuckle - Hook End Fittings HOO. END )ITTINGS

• Hot Dip galvanized steel.

• Quenched and Tempered.

• Hooks are forged with a greater cross sectional area that results in a stronger hook with better fatigue properties.

• Modified UNJ thread for improved fatigue properties.

• Fatigue Rated. g

n

i

t

t

i

F

d

n

E

k

o

o

H

-

e

l

k

c

u

b

n

r

u

T

HG-4037 Hook End Fittings Shank Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24

Shank Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610

RH Hook LH Hook Stock No. Stock No. 1070012 1070539 1070030 1070557 1070058 1070575 1070076 1070593 1070094 1070619 1070110 1070637 1070138 1070655 1070156 1070673 1070174 1070691 1070192 1070717 1070218 1070735 1070236 1070753 1070254 1070771 1070272 1070799 1070290 1070815 1070316 1070833 1070334 1070851 1070352 1070879 1070370 1070897 1070398 1070913 1070414 1070931 1070432 1070959 1070450 1070977 1070478 1070995 1070496 1071011 RH o k

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Working Load Limit (t) .18 .32 .45 .68 .68 .68 1.02 1.02 1.02 1.36 1.36 1.36 1.36 1.81 1.81 2.27 2.27 2.27 2.27 2.95 2.95 2.95 3.40 3.40 3.40

Weight Each (kg) .04 .07 .11 .24 .27 .31 .41 .47 .53 .70 .78 1.00 1.13 1.13 1.36 1.56 1.91 2.13 2.36 2.95 3.10 4.08 3.97 4.51 5.08

Dimensions (mm) A 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1

B 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 33.3 33.3 33.3

C 10.4 12.7 15.5 19.8 19.8 19.8 25.4 25.4 25.4 30.5 30.5 30.5 30.5 35.1 35.1 38.9 38.9 38.9 38.9 46.0 46.0 46.0 44.5 44.5 44.5

D 11.4 12.7 14.2 16.8 16.8 16.8 22.9 22.9 21.3 24.9 24.9 24.9 24.9 28.7 28.7 31.8 31.8 31.8 31.8 38.1 38.1 38.1 47.8 47.8 47.8

F 32.3 38.1 45.0 58.0 58.0 58.0 71.5 71.5 71.5 84.5 84.5 84.5 84.5 96.0 96.0 108 108 108 108 130 130 130 146 146 146

G 12.7 14.2 15.7 20.6 20.6 20.6 25.4 25.4 25.4 28.7 28.7 28.7 28.7 31.8 31.8 35.1 35.1 35.1 35.1 44.5 44.5 44.5 57.0 57.0 57.0

H 65.0 76.5 97.0 108 146 184 116 154 192 116 154 192 268 198 274 128 204 281 357 210 287 363 221 298 374

I 84.0 97.0 125 140 178 216 156 194 232 175 213 251 327 267 343 207 282 359 435 307 383 459 339 415 491

L 101 118 149 170 208 246 194 232 270 219 258 296 372 318 394 263 339 415 491 375 452 528 412 488 564

149

Rigging Accessories

s

Turnbuckle - Eye End Fittings E<E END )ITTINGS

• Hot Dip galvanized steel.

• Quenched and Tempered.

• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 6 mm through 64 mm, a shackle one size smaller can be reeved through eye.

• Modified UNJ thread for improved fatigue properties.

• Fatigue Rated. s

g

n

i

t

t

i

F

d

n

E

e

y

E

-

e

l

k

c

u

b

n

r

u

T

HG-4037 Eye End Fittings Shank Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

150

Shank Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

RH Eye

RH Eye Stock No. 1071057 1071075 1071093 1071119 1071137 1071155 1071173 1071191 1071217 1071235 1071253 1071271 1071299 1071315 1071333 1071351 1071379 1071397 1071413 1071431 1071459 1071477 1071495 1071510 1071538 1071574 1071592 1071618 1071636 1071654

LH Eye Stock No. 1071672 1071690 1071716 1071734 1071752 1071770 1071798 1071814 1071832 1071850 1071878 1071896 1071912 1071930 1071958 1071976 1071994 1072010 1072038 1072056 1072074 1072092 1072118 1072136 1072154 1072190 1072216 1072234 1072252 1072270

Working Load Limit (t) .23 .36 .54 1.00 1.00 1.00 1.59 1.59 1.59 2.36 2.36 2.36 2.36 3.27 3.27 4.54 4.54 4.54 4.54 6.89 6.89 6.89 9.71 9.71 9.71 12.7 12.7 16.8 27.2 34.0

Weight Each (kg) .03 .06 .11 .21 .25 .29 .38 .44 .47 .56 .64 .73 .90 1.16 1.39 1.40 1.70 2.01 2.10 2.95 3.31 3.76 3.49 5.90 5.28 7.82 8.34 14.1 19.4 31.7

Dimensions (mm) A 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 63.5 70.0

H 65.0 74.0 96.5 103 141 179 109 147 185 116 154 192 268 198 274 128 204 281 357 210 287 363 221 298 374 309 385 396 437 440

R 19.8 23.8 28.4 36.5 36.5 36.5 44.4 44.4 44.4 53.0 53.0 53.0 53.0 60.4 60.4 76.0 76.0 76.0 76.0 90.5 90.5 90.5 103 103 103 117 117 146 165 177

S 8.65 11.1 13.4 18.2 18.2 18.2 22.3 22.3 22.3 25.4 25.4 25.4 25.4 31.7 31.7 36.5 36.5 36.5 36.5 46.0 46.0 46.0 54.0 54.0 54.0 60.4 60.4 68.3 79.2 82.5

U 5.60 7.10 8.65 11.2 11.2 11.2 12.7 12.7 12.7 15.8 15.8 15.8 15.8 19.1 19.1 22.4 22.4 22.4 22.4 28.5 28.5 28.5 31.8 31.8 31.8 38.1 38.1 44.5 51.0 57.0

V 19.8 25.4 31.0 40.4 40.4 40.4 47.8 47.8 47.8 57.0 57.0 57.0 57.0 70.0 70.0 81.0 81.0 81.0 81.0 103 103 103 117 117 117 137 137 157 181 197

W 104 122 154 189 228 266 215 253 291 242 280 319 395 337 413 301 377 453 529 419 496 572 457 533 609 538 614 700 744 781

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Turnbuckle - Jaw End Fittings -AW END )ITTINGS

• Hot dip galvanized steel.

• Quenched and Tempered.

• Forged jaw ends are fitted with bolts and nuts on sizes 6 mm through 64 mm, and pins and cotters on sizes 19 mm through 70 mm.

• Modified UNJ thread for improved fatigue properties.

• Fatigue Rated. g

n

i

t

t

i

F

d

n

E

w

a

J

-

e

l

k

c

u

b

n

r

u

T

Rigging Accessories

s

HG-4037 Jaw End Fittings Shank Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

Shank Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

RHJaw

RH Jaw Stock No. 1072298 1072314 1072332 1072350 1072378 1072396 1072412 1072430 1072458 1072476 1072494 1072519 1072537 1072555 1072573 1072591 1072617 1072635 1072653 1072671 1072699 1072715 1072733 1072751 1072779 1072813 1072831 1072859 1072877 1072895

LH Jaw Stock No. 1072911 1072939 1072957 1072975 1072993 1073019 1073037 1073055 1073073 1073091 1073117 1073135 1073153 1073171 1073199 1073215 1073233 1073251 1073279 1073297 1073313 1073331 1073359 1073377 1073395 1073439 1073457 1073475 1073493 1073518

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Working Load Limit (t) .23 .36 .54 1.00 1.00 1.00 1.59 1.59 1.59 2.36 2.36 2.36 2.36 3.27 3.27 4.54 4.54 4.54 4.54 6.89 6.89 6.89 9.71 9.71 9.71 12.7 12.7 16.8 27.2 34.0

Dimensions (mm) Weight Each (kg) .05 .09 .13 .26 .29 .32 .49 .54 .60 .78 .82 .95 1.12 1.50 1.73 1.77 2.07 2.34 2.61 3.37 3.80 4.29 5.62 6.30 8.95 8.95 8.95 16.5 28.3 42.9

A 6.35 7.85 9.65 12.7 12.7 12.7 16.0 16.0 16.0 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 63.5 70.0

B 11.4 12.7 13.7 16.5 16.5 16.5 20.1 20.1 20.1 23.9 23.9 23.9 23.9 28.7 28.7 34.0 34.0 34.0 34.0 44.5 44.5 44.5 52.3 52.3 52.3 66.0 66.0 66.5 76.5 92.2

C 22.9 25.4 27.4 36.3 36.3 36.3 42.7 42.7 42.7 50.0 50.0 50.0 50.0 61.5 61.5 67.0 67.0 67.0 67.0 91.5 91.5 91.5 101 101 101 118 118 142 148 167

D 7.60 7.60 9.15 10.7 10.7 10.7 14.0 14.0 14.0 17.5 17.5 17.5 17.5 20.6 20.6 23.9 23.9 23.9 23.9 31.0 31.0 31.0 37.3 37.3 37.3 43.7 43.7 53.0 60.5 73.0

F 16.0 17.5 20.6 25.4 25.4 25.4 33.3 33.3 33.3 41.1 41.1 41.1 41.1 47.8 47.8 54.0 54.0 54.0 54.0 66.5 66.5 66.5 79.0 79.0 79.0 89.0 89.0 106 143 155

H 65.0 74.0 96.5 103 141 179 109 147 185 116 154 192 268 198 274 128 204 281 357 210 287 363 221 298 374 309 385 396 437 441

I Nom. Min. 91.0 109 164 202 240 185 223 261 205 243 281 357 303 379 249 223 299 376 452 336 412 488 354 431 507 470 546 604 650 679

L Nom. Min. 100 119 178 216 254 205 243 281 230 268 306 382 331 407 280 255 331 407 483 375 451 528 400 476 552 523 599 670 739 781

Y 28.4 35.3 37.8 46.0 46.0 46.0 59.5 59.5 59.5 71.0 71.0 71.0 71.0 82.0 82.0 94.5 94.5 94.5 94.5 124 124 124 134 134 134 159 159 184 229 242

MM 35.8 35.8 40.1 47.2 47.2 47.2 62.0 62.0 62.0 65.0 65.0 65.0 65.0 78.5 78.5 87.5 87.5 87.5 87.5 115 115 115 130 130 130 152 152 174 190 214

OO BoltPin 6.35 6.35 7.85 9.65 9.65 9.65 12.7 12.7 12.7 15.7 15.7 15.7 15.7 19.1 19.1 22.4 22.4 22.4 22.4 28.4 28.4 28.4 35.1 35.1 35.1 41.1 41.1 51.0 57.0 70.0

151

Turnbuckles - Body Only HG-2510 %OD<

• • • • •

Hot Dip galvanized.

Heat treat by normalizing.

UNC threads Fatigue Rated.

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1, Form 1 - Class 2, except for those provisions required by the contractor. y

Shank Diameter & Take Up (in.)

1/4 x 4 5/16 x 4-1/2 3/8 x 6 1/2 x 6 1/2 x 9 1/2 x 12 5/8 x 6 5/8 x 9 5/8 x 12 3/4 x 6 3/4 x 9 3/4 x 12 3/4 x 18 7/8 x 12 7/8 x 18 1x6 1 x 12 1 x 18 1 x 24 1-1/4 x 12 1-1/4 x 18 1-1/4 x 24 1-1/2 x 12 1-1/2 x 18 1-1/2 x 24 1-3/4 x 18 1-3/4 x 24 2 x 24 2-1/2 x 24 2-3/4 x 24

152

Shank Diameter & Take Up (mm) 6.35 x 102 7.94 x 114 9.53 x 152 12.7 x 152 12.7 x 229 12.7 x 305 15.9 x 305 15.9 x 229 15.9 x 305 19.1 x 152 19.1 x 229 19.1 x 305 19.1 x 457 22.2 x 305 22.2 x 457 25.4 x 152 25.4 x 305 25.4 x 457 25.4 x 610 31.8 x 305 31.8 x 457 31.8 x 610 38.1 x 305 38.1 x 457 38.1 x 610 44.5 x 457 44.5 x 610 51.0 x 610 63.5 x 610 70.0 x 610

HG-2510

HG-2510 Stock No. 1033893 1033919 1033937 1033955 1033973 1033991 1034017 1034035 1034053 1034071 1034099 1034115 1034133 1034179 1034197 1034213 1034231 1034259 1034277 1034339 1034357 1034375 1034437 1034455 1034473 1034552 1034570 1034632 1034678 1034696

Working Load Limit (t) .23 .36 .54 1.00 1.00 1.00 1.59 1.59 1.59 2.36 2.36 2.36 2.36 3.27 3.27 4.54 4.54 4.54 4.54 6.89 6.89 6.89 9.71 9.71 9.71 12.7 12.7 16.8 27.2 34.0

Weight Each (kg) .07 .09 .13 .27 .31 .45 .41 .54 .65 .59 .79 .94 1.13 1.22 1.72 1.12 1.78 2.39 3.35 2.38 3.52 4.61 3.97 4.99 6.21 7.43 9.64 12.5 24.5 24.5

l

n

O

y

d

o

B

-

s

e

l

k

c

u

b

n

r

u

T

Dimensions (mm) AA 121 138 181 191 267 343 200 276 353 210 286 362 514 371 524 229 381 533 686 384 536 689 400 552 705 568 721 737 789 789

BB 102 114 152 152 229 305 152 229 305 152 229 305 457 305 457 152 305 457 610 305 457 610 305 457 610 457 610 610 610 610

CC 9.65 11.9 14.2 19.1 19.1 19.1 23.9 23.9 23.9 28.4 28.4 28.4 28.4 33.3 33.3 38.1 38.1 38.1 38.1 39.6 39.6 39.6 47.8 47.8 47.8 55.5 55.5 63.5 89.5 89.5

DD 18.3 20.6 22.4 28.4 28.4 28.4 35.1 35.1 35.1 42.9 42.9 42.9 42.9 49.3 49.3 57.0 57.0 57.0 57.0 66.5 66.5 66.5 76.0 76.0 76.0 92.0 92.0 105 143 143

EE 8.65 9.65 9.65 12.7 12.7 12.7 15.7 15.7 15.7 19.1 19.1 19.1 19.1 22.4 22.4 25.4 25.4 25.4 25.4 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 51.0 70.0 70.0

GG 12.7 14.2 15.7 20.6 20.6 20.6 25.4 25.4 25.4 28.4 28.4 28.4 28.4 33.3 33.3 38.1 38.1 38.1 38.1 47.8 47.8 47.8 57.0 57.0 57.0 66.5 66.5 76.0 98.5 98.5

HH 9.65 11.2 12.7 15.7 15.7 15.7 19.1 19.1 19.1 23.9 23.9 23.9 23.9 26.9 26.9 31.8 31.8 31.8 31.8 38.1 38.1 38.1 44.5 44.5 44.5 54.0 54.0 60.5 79.0 79.0

JJ 4.30 4.85 4.85 6.35 6.35 6.35 7.85 7.85 7.85 9.65 9.65 9.65 9.65 11.2 11.2 12.7 12.7 12.7 12.7 14.2 14.2 14.2 15.7 15.7 15.7 19.1 19.1 22.4 31.8 31.8

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Stub End Turnbuckles • • • •

Complete assembly is self - colored.

End fittings are Quenched and Tempered, bodies heat treated by normalizing.

Reference American Welding Society Specifications for proper welding procedures.

Meets the performance requirements of Federal Specifications FF-T-791b, Type 1, Form 1 - CLASS 3, and ASTM F-1145, except for those provisions required of the contractor. s

e

l

k

c

u

b

n

r

u

T

d

n

E

b

u

t

S

HS-251 Stub End Turnbuckles Shank Diameter & Take up (in.)

3/8 x 6 1/2 x 6 5/8 x 6 3/4 x 6 7/8 x 6 1x6 1 x 12 1-1/8 x 6 1-1/4 x 6 1-1/4 x 12 1-1/2 x 12

Shank Diameter & Take up (mm) 9.53 x 152 12.7 x 152 15.9 x 305 19.1 x 152 22.2 x 152 25.4 x 152 25.4 x 305 28.6 x 152 31.8 x 152 31.8 x 305 38.1 x 305

HS-251

HS-251 Stock No. 1033143 1033161 1033223 1033287 1033367 1033429 1033447 1033508 1033526 1033544 1033642

Working Load Limit (t) .54 1.00 1.59 2.36 3.27 4.54 4.54 5.62 6.89 6.89 9.71

s

t

u

N

Weight Each (kg) .34 .57 .96 1.48 2.17 2.88 3.99 4.03 4.62 6.17 9.27

k

c

o

Dimensions (mm) A 9.65 12.7 16.0 19.1 22.4 25.4 25.4 28.7 31.8 31.8 38.1

R 152 152 152 152 152 152 304 152 152 304 304

S 181 190 200 209 219 228 381 231 231 384 400

T 14.2 19.1 23.8 28.7 33.2 38.1 38.1 39.6 39.6 39.6 47.7

U 113 108 103 111 119 127 127 125 138 138 137

W 406 406 406 431 457 482 635 482 508 660 673

L

/OC. NUTS

HG-4060 / HG-4061 Lock Nuts Dimensions (mm)

HG-406

Thread Diameter (in.)

1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 2-3/4

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Right Hand HG-4060 Stock No. 1075115 1075133 1075151 1075197 1075213 1075231 1075259 1075277 1075311 1075357 1075393 1075419 1075455 1075473

Left Hand HG-4061 Stock No. 1075491 1075516 1075534 1075570 1075598 1075614 1075632 1075650 1075696 1075730 1075776 1075794 1075838 1075856

Weight Per 100 (kg) .36 .59 .91 1.81 3.18 4.99 7.39 10.8 28.3 32.7 51 68 150 193

O 11.2 12.7 14.2 19.1 23.9 28.7 33.3 38.1 47.8 57.0 70.0 79.0 98.5 108

P 12.7 14.2 16.3 21.8 26.9 32.0 38.1 42.9 54.0 64.5 81.0 91.5 114 125

Q 4.05 4.85 5.60 7.85 9.65 10.7 12.2 14.0 18.3 21.3 25.4 28.4 38.1 41.1

153

Rigging Accessories

HS-251

FORGED EYE BOLT WARNINGS AND APPLICATION INSTRUCTIONS

• • • •

Regular Nut Eye Bolt G-291

Shoulder Nut Eye Bolt G-277

WARNING Loads may slip or fall if proper eye bolt assembly and lifting procedures are not used.

A falling load can seriously injure or kill.

Read and understand both sides of these instructions, and follow all eye bolt safety information presented here.

Read, understand, and follow information in diagrams and charts below before using eye bolt assemblies.

Machinery Eye Bolt S-279

Important Safety Information Read & Follow

• • • • • • • • •

Inspection/Maintenance Safety: Always inspect eye bolt before use.

Never use eye bolt that shows signs of wear or damage.

Never use eye bolt if eye or shank is bent or elongated.

Always be sure threads on shank and receiving holes are clean.

Never machine, grind, or cut eye bolt.

Assembly Safety: Never exceed load limits specified in Table I.

Never use regular nut eye bolts for angular lifts.

Always use shoulder nut eye bolts (or machinery eye bolts) for angular lifts.

For angular lifts, adjust working load as follows: Direction of Pull 45 degrees 90 degrees

• • • •

Never undercut eye bolt to seat shoulder against the load.

Always countersink receiving hole or use washers to seat shoulder.

Always screw eye bolt down completely for proper seating.

Always tighten nuts securely against the load.

Size (mm)

Working Load Limit (kg)

6.35

295

7.94

544

9.53

703

12.7

1179

15.9

2351

19.1

3266

22.2

4808

25.4

6033

31.8

9525

38.1

10886

•

IN - LINE

Adjusted Working Load 30% of rated working load 25% of rated working load

Table 1 (In - Line Load)

154

Shoulder Nut Eye Bolt — Installation for Angular Loading

45 degrees

•

90 degrees

•

Thickness of spacers must exceed this distance between the bottom of the load and the last thread of the eye bolt.

•

The threaded shank must protrude through the load sufficiently to allow full engagement of the nut.

If the eye bolt protrudes so far through the load that the nut cannot be tightened securely against the load, use properly sized washers to take up the excess space BETWEEN THE NUT AND THE LOAD.

Place washers or spacers between nut and load so that when the nut is tightened securely, the shoulder is secured flush against the load surface.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

IMPORTANT - Read and understand these instructions before using eye bolts.

Regular Nut & Shoulder Nut Eye Bolt - Installation for In-line Loading Right

Right More than one eye bolt diameter of threads, only (1) nut required.

Right

Wrong Tighten Hex Nut Securely Against Load

One eye bolt diameter of threads or less, use two (2) nuts.

Tighten hex nut securely against load

Tap Depth: 2.5 x Diameter 2 x Diameter (Minimum)

One eye bolt diameter or less

Tighten hex nut securely against load

Operating Safety

• • •

Always stand clear of load.

Always lift load with steady, even pull – do not jerk.

Always apply load to eye bolt in the plane of the eye – not at an angle.

Do not reeve slings from one eye bolt to another.

This will alter the load and angle of loading on the eye bolt.

Wrong Resultant Load

• •

Never exceed the capacity of the eye bolt–see Table I. When using lifting slings of two or more legs, make sure the loads in the legs are calculated using the angle from the vertical to the leg and properly size the shoulder nut or machinery eye bolt for the angular load.

Buckling may occur if the load is not stiff enough to resist the compressive forces which result from the angular loading.

After slings have been properly attached to the eye bolts, apply force slowly.

Watch the load carefully and be prepared to stop applying force if the load starts buckling.

Machinery Eye Bolt - Installation for In – line & Angular Loading Table II

These eye bolts are primarily intended to be installed into tapped holes.

1.After the loads on the eye bolts have been calculated, select the proper size eye bolt for the job.

For angular lifts, adjust working load as follows:

Direction of Pull 45 degrees 90 degrees

Adjusted Working Load 30% of rated working load 25% of rated working load

2. Drill and tap the load to the correct sizes to a minimum depth of one-half the eye bolt size beyond the shank length of the machinery eye bolt.

3. Thread the eye bolt into the load until the shoulder is flush and securely tightened against the load.

4. If the plane of the machinery eye bolt is not aligned with the sling line, estimate the amount of unthreading rotation necessary to align the plane of the eye properly.

Remove the machinery eye bolt from the load and add shims (washers) of proper thickness to adjust the angle of the plane of the eye to match the sling line. Use Table II to estimate the required shim thickness for the amount of unthreading rotation required.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Eye Bolt Size (mm)

Shim Thickness Required to Change Rotation 90° (mm)

6.35

0.30

7.94

0.35

9.53

0.40

12.7

0.50

15.9

0.60

19.1

0.65

22.2

0.70

25.4

0.80

31.8

0.90

38.1

1.05

Shim added to change eye alignment 90°

Minimum tap depth is basic shank length plus one-half the nominal eye bolt diameter.

155

CROSBY® SWIVEL HOIST RINGS WARNINGS AND APPLICATION INSTRUCTIONS

• • • •

HR-125

HR-1000

(Red Washer)

(Red Washer)

HR-125 M

HR-1000M

(Silver Washer)

(Silver Washer)

HR-125C

HR-125W

Hoist Ring Application Assembly Safety

• • • • • • • • •

Use swivel hoist ring only with a ferrous metal (steel, rion) or soft metal (i.e., aluminum) loads (work piece). Do not leave threaded end of hoist ring in aluminum loads for long time periods due to corrosion.

After determining the loads on each hoist ring, select the proper size hoist ring using the Working Load Limit ratings in Table 1,2,& 4 for UNC threads and Table 3 for Metric threads.

Drill and tap the work piece to the correct size to a minimum depth of one-half the threaded shank diameter plus the threaded shank length. See rated load limit and bolt torque requirements imprinted on top of the swivel trunnion (See Table 1 and/or Table 3).

Install hoist ring to recommended torque with a torque wrench making sure the bushing flange meets the load (work piece) surface.

Never use spacers between bushing flange and mounting surface.

Always select proper load rated lifting device for use with Swivel Hoist Ring.

Attach lifting device ensuring free fit to hoist ring bail (lifting ring) (Fig. 1) Apply partial load and check proper rotation and alignment.

There should be no interference between load (work piece) and hoist ring bail (Fig. 2) Special Note: When a Hoist Ring is installed with a retention nut, the nut must have a full thread engagement and must meet one of the following standards to develop the Working Load Limit (WLL).

1.ASTM A-563 (A) Grade D Hex Thick (B) Grade DH Standard Hex 2.SAE Grade 8 — Standard Hex

WRONG

WRONG

• • •

WARNING Loads may slip or fall if proper Hoist Ring assembly and lifting procedures are not used.

Read and Understand these warnings and application instructions.

A falling load may cause serious injury or death.

Install hoist ring bolt to torque requirements listed in tables 1,2,3, & 4. For the HR-125,HR-1000, HR125C, HR-125M, HR-1000M and HR125W respectively.

Web sling HR-125W connecting bolt must be securely tightened in place. The jam nut must then be securely tightened onto the connecting bolt, see Table 4, last column.

Chain sling HR-125C connecting pin must be in place properly secured with the locking pin into the clevis ears.

Do not use with damaged slings or chain.

For inspection criteria see ASME B30.9 Use only genuine Crosby parts as replacements.

Hoist Ring Inspection / Maintenance

• • • • • • • • •

• •

Always inspect hoist ring before use.

Regularly inspect hoist ring parts (Fig.3).

Never use hoist ring that shows signs of corrosion, wear or damage.

Never use hoist ring if bail is bent or elongated.

Always be sure threads on shank and receiving hole are clean, not damaged, and fit properly.

Always check with torque wrench before using an already installed hoist ring.

Always make sure there are no spacers (washers) used between bushing flange and the mounting surface. Remove any spacers (washers) and retorque before use.

Always ensure free movement of bail. The bail should pivot 180 degrees and swivel 360 degrees (Fig. 4).

Always be sure total work piece surface is in contact with hoist ring bushing mating surface. Drilled and tapped hole must be 90 degrees to load (work piece) surface.

Operating Safety Never exceed the capacity of the swivel hoist ring, see Table 1,2, and 4 for UNC threads and Table 3 for Metric threads.

When using lifting slings of two or more legs, make sure the forces in the legs are calculated using the angle from the vertical to the leg and select the proper size swivel hoist ring to allow for the angular forces.

E x t ern al In sp ection Points

Free Movement

156

Figure 2

180° Pivot

Possible Wear

Thread Damage

Figure 1

RIGHT

Figure 3

360° Rotation

Figure 4 Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

Table 1 HR-125 Hoist Working Ring Bolt Load Limit* Torque 5:1 in Ft. lbs. † (lbs.)

HR-125 Bolt Size ‡ (in.)

Effective Thread Projection Length (in.)

HR-1000 Effective Thread HR-1000 Projection Length Bolt Size ‡ (in.) (in.)

800 ††

7

5⁄ 16

- 18 x 1.50

.59

5⁄ 16

- 18 x 1.50

.52

1000 ††

12

3⁄ 8

- 16 x 1.50

.59

3⁄ 8

- 16 x 1.50

.52

2500

28

1⁄ 2

- 13 x 2.00

.71

1⁄ 2

- 13 x 2.25

.69

2500 ††

28

1⁄ 2

- 13 x 2.50

1.21

1⁄ 2

- 13 x 2.75

1.19

4000

60

5⁄ 8

- 11 x 2.00

.71

5⁄ 8

- 11 x 2.25

.69

60

5⁄ 8

- 11 x 2.75

1.46

5⁄ 8

- 11 x 3.00

1.44

5000

100

3⁄ 4

- 10 x 2.25

.96

3⁄ 4

- 10 x 2.50

.94

5000 ††

100

3⁄ 4

-10 x 2.75

1.46

3⁄ 4

-10 x 3.00

1.44

**

100

3⁄ 4

- 10 x 2.75

.90

3⁄ 4

- 10 x 3.00

.85

7000 ††**

100

3⁄ 4

-10 x 3.50

1.65

3⁄ 4

-10 x 4.00

1.85

- 9 x 2.75

.90

7⁄ 8

- 9 x 3.00

.85

-9 x 3.50

7⁄ 8

-9 x 4.00

1 - 8 x 3.00 1 -8 x 4.00

1.65 1.15 2.15

1 -8 x 3.50 1 -8 x 4.50

1.85 1.35 2.35

††

4000

7000 8000

160

7⁄ 8

8000 †† 10000 10000 ††

160 230 230

7⁄ 8

15000

470

11⁄4 - 7 x 4.50

2.22

11⁄4 - 7 x 5.00

2.09

24000

800

11⁄2 - 6 x 6.50

2.98

11⁄2 - 6 x 5.50

2.59

30000

1100

2 -41⁄2 x 6.50

2.98

—

—

50000 75000

2100 4300

2-1⁄2 - 4 x 8.00 3 -4 x10.50

4.00 5.20

— —

— —

100000

6600

3-1⁄2 - 4 x13.00

7.00

—

—

4500†† 7100

WRONG

Buckling may occur if the load is not stiff enough to resist the compressive forces which result from the angular loading.

After slings have been properly attached to the hoist ring, apply force slowly. Watch the load and be prepared to stop applying force if the load starts buckling.

• •

** Ultimate Load is 4.5 times Working Load Limit for 7000# Hoist Ring when Tested in 90° orientation. All sizes are individually proof tested to 2-1/2 times the Working Load Limit. †, ††, ‡ (See footnote at bottom of page).

Table 2 HR-125C Swivel Hoist Ring to Grade 8 Chain Effective Working Load Hoist Ring Thread Bolt Projection Bolt Torque Limit Length Size in 4:1 (in.) (in.) ‡ Ft. lbs. † (lbs.) ** 4500 60 5/8 - 11 x 2.00 .71

Do not reeve slings from one bail to another. This will alter the load and angle of loading on the hoist ring.

• • •

WARNING A falling load may cause serious injury or death.

Chain sling HR-125C connecting pin must be properly secured with the locking pin into the clevis ears.

Do not use with damaged web slings or chain.

For inspection criteria see ASME B30.9 Before use, tighten bolt first, then tighten nut.

(HR-125W) Read, understand and follow all instructions and chart information before using web connector.

Spectrum 8 Chain Size (in. - mm) 1/4 - 7

7100†† 12000 12000††

60 100 100 230 230

5/8 - 11 x 2.75 3/4 - 10 x 2.75 3/4 - 10 x 3.50 1 - 8 x 3.00 1 - 8 x 4.00

1.46 .90 1.65 1.15 2.15

1/4 - 7 3/8 - 10 3/8 - 10 1/2 - 13 1/2 - 13

18100

470

1-1/4 - 7 x 4.00

2.22

5/8 - 16

See footnote at bottom of page.

Table 3 HR-125M

Working Load Limit (Kg) ***

HR-1000M HR-125M

Design Factor 5:1

Design Factor 4:1

Hoist Ring Bolt Torque in Nm †

400 450 1050 1900 2150 3000 4200 7000 11000 12500 13500

500 550 1300 2400 2700 3750 5250 8750 13750 15600 16900

10 16 38 81 136 136 312 637 1005 1005 1350

HR-1000M

Effective Thread Projection Length (mm)

Bolt Size ‡‡ (mm) M 8 x 1.25 x 40 M10 x 1.50 x 40 M12 x 1.75 x 50 M16 x 2.00 x 60 M 20 x 2.50 x 65 M 20 x 2.50 x 75 M 24 x 3.00 x 80 M 30 x 3.50 x 100 M 36 x 4.00 x 150 M 42 x 4.50 x 160 M 48 x 5.00 x 160

16.9 16.9 17.2 27.2 31.2 28.1 33.1 45.1 60.6 70.6 70.6

Bolt Size ‡‡ (mm)

Effective Thread Projection Length (mm)

M 8 x 1.25 x 40 M10 x 1.50 x 40 M12 x 1.75 x 55 M16 x 2.00 x 65 M 20 x 2.50 x 70 M 20 x 2.50 x 80 M 24 x 3.00 x 90 M 30 x 3.50 x 140 M 36 x 4.00 x 130 — —

16.0 16.0 15.5 26.1 31.1 25.4 36.0 66.8 56.2 — —

Designed to be used with ferrous work piece only.

HR-125W Web Sling Round Sling Size (No.)

Web Width (in.)

Eye Width (in.)

1&2 1&2 3 3 4

2 2 3 3 4

2 2 1.5 1.5 2

Table 4 HR-125W Swivel Hoist Ring to Webbing HR-125W Working Load Hoist Ring Bolt Limit Torque in 5:1 Ft. lbs. † (tons) * Ply. 2 2 2 2 2

3-1/4 3-1/4†† 4-1/2 4-1/2†† 6-1/4

100 100 230 230 470

Bolt Size (in.) ‡

Effective Thread Projection Length (in.)

Torque in Ft.-Lbs. Spool bolt and nut ‡‡‡

3/4 - 10 x 2.75 3/4 - 10 x 3.50 1 - 8 x 3.00 1 - 8 x 4.00 1-1/4 - 7 x 4.50

.90 1.65 1.15 2.15 2.22

90 90 110 110 130

* ** *** † ††

Ultimate load is 5 times the Working Load Limit. Individually proof tested to 2-1/2 times the Working Load Limit.

Ultimate load is 4 times the Working Load Limit. Individually tested to 2-1/2 the Working Load Limit.

Individually proof tested to 2-1/2 times the Working Load Limit based on 4:1 design factor.

Tightening torque values shown are based upon threads being clean, dry and free of lubrication.

Long bolts are designed to be used with soft metal (i.e., aluminum) work piece. While the long bolts may also be used with ferrous metal (i.e., steel & iron) work pies, short bolts are designedd for ferrous work pieces only. ‡ Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A574. All threads are UNC. ‡‡ Bolt specification is a Grade 12.9 Alloy socket head cap to DIN 912. All threads are metric (ASME/ANSI B18.3.1m) ‡‡‡ Tighten bolt to specified torque, then tighten nut to specified torque.

All Swivel Hoist Rings are individually proof tested to 2-1/2 times the Working Load Limit.

Copyright © 2002 The Crosby Group, Inc. All Rights Reserved

157

WARNING AND APPLICATION INSTRUCTIONS

HR-1200 Hoist Ring Application / Assembly Instruction

•

The Crosby side pull swivel hoist ring is designed to accept standard Crosby fittings to facilitate wider slings and quick attachment. In order to use the larger fittings, the load rating on the (shackle) fitting may be greater than the hoist ring frame. Never exceed the Working Load Limit of the hoist ring frame.

Use swivel hoist ring only with a ferrous metal (steel, iron) or non-ferrous (i.e., aluminum) loads ( work piece). Do not leave threaded end of hoist ring in aluminum loads for long time periods due to corrosion.

After determining the loads on each hoist ring, select the proper size hoist ring using the working Load Limit ratings in Table 1 for UNC threads and Table 2 for Metric threads.

Drill and tap the work piece to the correct size to a minimum depth of one-half the threaded shank diameter plus the threaded shank length.

Install hoist ring to recommended torque with a torque wrench making sure the bushing flange is fully supported by the load (work piece) surface. See rated load limit and bolt torque requirements imprinted on hoist ring body (See Table 1 or Table 2).

Never use spacers between bushing flange and mounting surface.

Always select proper lifting device for use with Swivel Hoist Ring (See Tables 1 & 2).

Attach lifting device ensuring free fit to hoist shackle (See Figure 3).

Apply partial load and check proper rotation and alignment of shackle. There should be no interference between load (work piece) and hoist shackle (See Figure 1 and Figure 3).

The Hoist ring should rotate into normal operating position, with shackle aligned with load as shown in Figure 3. If shackle is oriented as shown in Figure 4, DO NOT LIFT. Special Note: when a Hoist Ring is installed with a retention nut, the nut must have full thread engagement and must meet one of the following standards to develop the Working Load Limit (WLL).

1. ASTM A-563 (A) Grade D Hex Thick (B) Grade DH Standard Hex 2. SAE Grade 8 — Standard Hex

• • • • • • • • • •

Hoist Ring Inspection / Maintenance

• • • • •

Always inspect hoist ring before use.

Regularly inspect hoist ring parts (Figure 2).

For hoist rings used in frequent load cycles or on pulsating loads, the bolt threads should be periodically inspected by magnetic particle or dye penetrant.

Do not use part showing cracks, nicks or gouges.

Repair minor nicks or gouges to hoist frame by lightly grinding until surfaces are smooth. Do not reduce original dimension more than 10%. Do not repair by welding.

158

WARNING

• Loads may slip or fall if proper Hoist Ring assembly and lifting procedures are not followed.

• A falling load may cause serious injury or death.

• Install hoist ring bolt to torque requirements listed in tables.

• The side pull hoist ring frame will be only one part • • •

of a lifting system with several components (i.e., shackles and slings). Never exceed the Working Load Limit of the hoist ring frame.

Do not use damaged slings or chain. For inspection criteria, see ASME B30.9.

Read and understand these instructions before using hoist ring.

Use only genuine Crosby parts as replacements.

External Inspection Points

WRONG

Free movement of shackle pin

Thread Damage

Figure 2

Figure 1

RIGHT

WRONG

90 Pivot

Figure 3

• • • • • • •

Figure 4

Never use hoist ring that shows signs of corrosion, wear or damage.

Never use hoist ring if components are bent or elongated.

Always be sure threads on bolt and receiving tapped holes are clean, undamaged, and fit properly.

Always check with torque wrench before using an already installed hoist ring.

Always make sure there are no spacers (washers) used between bushing flange and the mounting surface. Remove any spacers (washers) and retorque before use.

Always ensure free movement of shackle. The shackle should pivot 90 and the hoist ring should swivel 360 (See Figure 3).

Always be sure total work piece surface is in contact with hoist ring bushing mating surface. Drilled and tapped hole must be 90 to load (work piece) surface.

Copyright© 2002 The Crosby Group, Inc. All Rights Reserved

Do not reeve slings from one bail to another. This will alter the load and angle of loading on the hoist ring.

After slings have been properly attached to the hoist ring, apply force slowly. Watch the load and be prepared to stop applying force if the load starts buckling.

Working Load Limit * (lbs.)

Hoist Ring Bolt Torque in Ft. Lbs.†

Bolt Size‡ (in.)

650†† 800†† 2000 2000†† 3000 3000†† 5000 5000†† 6500 6500†† 8000 8000††

7 12 28 28 60 60 100 100 160 160 230 230

5/16 - 18 x 1.5 3/8 - 16 x 1.5 1/2 - 13 x 2.0 1/2 - 13 x 2.5 5/8 - 11 x 2.0 5/8 - 11 x 2.75 3/4 - 10 x 2.75 3/4 - 10 x 3.5 7/8 - 9 x 2.75 7/8 - 9 x 3.5 1 - 8 x 3.0 1 - 8 x 4.0

.59 .59 .71 1.21 .71 1.46 1.46 1.65 .90 1.65 1.15 2.15

4

14000

470

1-1/4 - 7 x 4.5

2.22

5

17200 29000

800 1100

1-1/2 - 6 x 6.5 2 - 4-1/2 x 6.5

2.98 2.98

2

3

HR1200M Metric Threads

Frame Size

Working Load Hoist Ring Limit * Bolt Torque (kg) Nm †

Never exceed the capacity of the hoist ring, seeTable 1 for UNC threads and Table 2 for Metric threads.

When using lifting slings of two or more legs, make sure the forces in the legs are calculated using the angle from the vertical to the leg and select the proper size swivel hoist ring to allow for the angular forces.

TABLE 1 Effective Thread Projection Length (in.)

1

• •

Buckling may occur if the load is not stiff enough to resist the compressive forces which result from the angular loading.

HR1200 UNC Threads

Frame Size

OPERATING SAFETY

WRONG

Recommended Shackles Red Pin ® Red Pin ® Shackles 209, 210, 213, Web Shackles 215, 2130, 2150 S-281 (t) (tons)

1/2" - (2) 5/8" - (3-1/4)

2" - (3-1/4)

5/8" - (3-1/4) 3/4" - (4-3/4)

2" - (3-1/4) 1-1/2" - (4-1/2)

7/8" - (6-1/2)

2" - (6-1/4)

1" - (8-1/2) 1-1/8" - (9-1/2) 1-1/4" - (12) 1-3/8" - (13-1/2) 1-1/2" - (17) 1-3/4 - (25)

3" - (8-1/2)

—

TABLE 2

Bolt Size (mm) ‡‡

Effective Thread Projection Length (mm)

1

300 400

10 16

M8 x 1.25 x 40 M10 x 1.5 x 40

16.9 16.9

2

1000 1400

38 81

M12 x 1.75 x 50 M16 x 2.00 x60

17.2 27.2

3

2250 3500

136 312

M20 x 2.50 x75 M24 x3.00 x80

28.1 33.1

4

6250

637

M30 x 3.5 x120

45.1

5

7750 10000 13000

1005 1005 1350

M36 x 4.0 x 150 M42 x 4.5 x 160 M48 x 5.0 x 160

60.6 70.6 70.6

Recommended Shackles Red Pin ® Red Pin ® Shackle 209, 210, 213, Web Shackles 215, 2130, 2150 S-281 (t) (tons)

1/2" - (2) 5/8" - (3-1/4

5/8" - (3-1/4) 3/4" - (4-3/4

2" - (3-1/4) 1-1/2" - (4-1/2)

7/8" - (6-1/2)

2" - (6-1/4)

1" - (8-1/2) 1-1/8" - (9-1/2) 1-1/4" - (12) 1-3/8" - (13-1/2) 1-1/2" - (17) 1-3/4 - (25)

2" - (3-1/4)

3" - (8-1/2)

—

Designed to be used with Ferrous work piece only * Ultimate load is 5 times the Working Load Limit. Individually proof tested to 2-1/2 times the Working Load Limit. † Tightening torque values shown are based upon threads being clean, dry and free of lubrication. †† Long bolts are designed to be used with soft metal (i.e., aluminum) work piece. While the long bolts may also be used with ferrous metal (i.e., steel & iron) work pies, short bolts are designedd for ferrous work pieces only. ‡ Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A574. All threads are UNC - 3A. ‡‡ Bolt specification is a Grade 12.9 Alloy socket head cap to DIN 912. All threads are metric (ASME/ANSI B18.3.1m)

Copyright© 2002 The Crosby Group, Inc. All Rights Reserved

159