Rev 2:1
101E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
101E 101ED 101ES
BMW X1 (E84)
Powder Coated Finish
e11*94/20*9627*00
w
Components
Mainframe
Code
Quantity
CB
1
Description
Bolt Kit Code
Crossbar
Quantity
Description
1
Fitting Instruction
6
Plastic Fixings
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear light clusters, fixings inside boot. 2. Remove bumper—8 fixings on lower edge, 3 fixings in each wheel arch. Pull back lower edge of wheel arch surround trim to reveal 1 fixing in each arch and remove. With the aid of lubricant carefully pull out bumper tips and ease bumper rearwards. Disconnect reversing sensors if fitted. 3. Lower exhaust from hanger on bumper impact beam and remove impact beam. Retain fixings 4. Locate crossbar CB onto threaded studs. Locate impact beam over the crossbar and secure in position using original fixings. Fully tighten. 5. Refit bumper and light clusters. Re attach wheel arch liners using plastic fixings provided. Detachable Neck: Attach to crossbar CB using set screws Z.
Swan Neck: Attach to crossbar CB with CPE10 plates (standard orientation) using set screws Y & bolts W
Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball using set screws G. 6. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
101E 101ED 101ES
BMW X1 (E84)
Powder Coated Finish
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com