Rev 2:1
133E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
133E 133ED 133ES
Powder Coated Finish
VAUXHALL MOKKA 2012CHEVROLET TRAX 2013E11 55R-0110092 w614
Components
Mainframe
Description
Bolt Kit
Code
Quantity
CB
1
Crossbar
Code
Quantity
B
6
12x35 Set Screws, Nuts & Grip Washers
LA
1
Left Angle
RA
1
Right Angle
WA
Description
C
2
12x35 Set Screws & Grip Washers
WB
6
12mm Large Round Washers
4
10mm Large Round Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove light clusters— 4 nuts behind panels in boot. Remove cover from the side of light cluster to reveal 1 screw & remove. Slide out light cluster and disconnect wiring loom.
2.
Remove bumper— 5 fixings inside each wheel arch. Unclip arch trim to reveal hidden fixings. Remove plastic fixings from lower edge of bumper. Unclip bumper sides & remove whilst disconnecting any wiring.
3.
Remove impact beam & hand to customer but retain fixings. Remove bumper support brackets.
4.
Insert angles LA & RA inside the chassis rails and loosely attach using set screws C with washers WB from under the vehicle. Attach angles LA & RA to the rear panel using set screws B with washers WB & original fixings X with washers WA.
5.
Loosely attach crossbar CB to angles LA & RA using bolts B.
6.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
7.
Cut bumper as shown in diagram.
8.
Refit bumper, lights & any wiring.
Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates (standard orientation) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using bolts A, then attach type approved towball (not supplied) with set screws G. 9.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
133E 133ED 133ES
Powder Coated Finish
VAUXHALL MOKKA CHEVROLET TRAX
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com