Rev 2:1
152E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
152E 152ED 152ES
Powder Coated Finish
NISSAN XTRAIL (Fog & Reverse Lamps In Bumper T31) 2007-2014 (Exc Platinum) e11*94/20*8333*00 w920
Components Mainframe
Code
Quantity
CB
1
Crossbar
Description
Bolt Kit Code
Quantity
WB
4
8mm Large Round Washers
Description
LA
1
Left Angle
C
4
8x35 Set Screws & Grip Washers
RA
1
Right Angle
NT
2
16mm Nuts & Grip Washers
LS
1
Left Sideplate
WA
10
10mm Large Round Washers
RS
1
Right Sideplate
WC
4
12mm Small Round Washers
SW
2
Spacer Washers
B
10
10x40 Set Screws & Grip Washers
E
4
12x40 Set Screws & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1 2
Remove mud flaps— 3 screws either side. Remove rear bumper— 2 plastic fixings on the bottom edge, 2 screws from the bottom corner of the wheel arches. Remove inner corner plastic trim from inside wheel arches. Gently pull wheel arch trim from the lowest point to reveal fixings in the bumper. Note — use of lubricant will aid removal as the clips break easily. 3 Remove fixing holding metal hook bracket to wheel arch. Remove tip screws inside wheel arches. With the boot door open, remove plastic covers 1 either side and remove the revealed fixings. Pull out bumper tips and gently unclip the top edge of the bumper from the hidden clips. Note — use of lubricant will aid removal as the clips break easily. Take care not to pull on the wiring harness. Disconnect the reversing light and fog light. 4 Remove impact beam and its support brackets. Lower the exhaust from two rubber mountings. 5 Insert left angle LA and right angle RA inside the chassis rails and loosely secure using set screws B with washers WA. 6 Loosely attach left side plate LS and right side plate RS to the rear panel using bolts C with washers WB. 7 Loosely attach left and right angles LA and RA to left and right side plates LS and RS using spacer washers SW and nuts NT. 8 Loosely attach crossbar CB to left side plate LS and right side plate RS using set screws E and washers WC. 9. Cut bumper as shown in diagram. Refer to section 2 and refit bumper. Re-fit mud flaps. Re-fit exhaust. Detachable neck: Attach detachable neck D to crossbar CB using set screws Z. Swan neck: Attach swan neck SN to crossbar CB with IP plates using fasteners A. Flange neck: Attach flange neck F to crossbar CB using A. Attach a type approved towball (not supplied) using set screws G. 10. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
152E 152ED 152ES
Powder Coated Finish
NISSAN XTRAIL (Fog & Reverse Lamps In Bumper T31) (Exc Platinum)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com