Rev 2:1
193E 193ED
BMW X5 (E70) (Inc Facelift) (Inc M-Sport) & BMW X6 (E71) 2008-2014
Powder Coated
e11*94/20*9521*00
w156
Components
Mainframe
Code
Quantity
CB
1
Bolt Kit
Description Crossbar
Code
Quantity
WA
8
12mm Large Round Washers
Description
PPF
8
Push In Plastic Fastener
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. X5: Remove lower section of bumper (6 fixings along lower edge, 3 plastic rivets holding wheel arch surround to arch liner, unclip arch surround to reveal one fixing on lower corners each side). Remove reflectors from bumper skin to reveal 1 fixing behind each and remove. With the aid of lubricant pull out the lower bumper tips and pull the bumper rearwards whilst disconnecting the reversing sensors if fitted. Note: The bumper is held by clips along the upper edge. 2. X6: Remove both sections of bumper, lower section first. The extra fixings securing the upper section are along its bottom edge attaching it to the support frame and plastic rivets behind the wheel arch surround. 3. Remove impact beam and hand to customer. Retain fixings. 4. X6 ONLY: Locate crossbar CB onto the studs on the rear panel and mark off the support frame. Cut out two sections 35mm deep. 5. Attach crossbar CB to rear panel using original fixings with washers WA. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 6. Re-attach top section of bumper on X6. Cut each lower bumper according to diagram and re-attach along with reversing sensors and reflectors. Re-attach wheel arch surround using plastic rivets supplied. Detachable Neck: Attach to crossbar CB using set screws Z. Flange Neck: Attach to crossbar CB using bolts A with type approved towball (not supplied) using set screws B. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
193E 193ED
Powder Coated
BMW X5 (E70) (Inc Facelift) (Inc M-Sport) & BMW X6 (E71) 2008-2014
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
193E
FLANGE NECK
Powder Coated
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A B
2 2
w493
Description
12x100 Bolts,Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws B. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com