Rev 2:2
210E 210ED
Powder Coated Finish
RANGE ROVER 2002-2013 (L3) e11*94/20*9551*00
w694g
Components
Mainframe
Code
Quantity
CB
1
Crossbar
Description
LA
1
RA
1
Bolt Kit Code
Quantity
C
4
8x30 Set Screws, Nuts & Grip Washers
Description
Left Angle
WA
4
8mm Large Round Washers
Right Angle
WB
2
10mm Small Round Washers
B
4
16x50 Set Screws, Grip Washers & 2 Nuts
E
2
10x30 Set Screws, Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove Bumper— 4 nuts each side on rear panel inside boot (remove trim to gain access), 2 screws inside each wheel arch. Remove mud flaps if fitted. Unclip top edges of bumper from the wings (use lubricant to ease removal as the clips can easily break). Disconnect reversing sensors if fitted.
2.
Lower the rear exhaust silencers by removing the fixings attached to the towing eyes. Remove towing eye brackets and hand to customer. Retain bolts for refitting.
3.
Loosely attach left angle LA and right angle RA to the chassis rails using original towing eye bolts. Replace bumper.
4.
Loosely attach crossbar CB to angles LA and RA using set screws B. Tighten all fixings.
5.
Re-attach exhaust to angles LA and RA using set screws C with washers WA or set screws E with washers WB.
6.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
Detachable Neck: Attach using set screws Z. Flange Neck: Attach using bolts A and type approved towball (not supplied) using set screws G.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
210E 210ED
Powder Coated Finish
RANGE ROVER (L3)
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
210E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com