Engine - Engine and crankcase

from New Holland T4.55 PowerStar Tractor Service Repair Manual

Engine - Engine and crankcase

Insert the three hooks the chain the eyelets the Using a lift the assembly f the platform

10. Position the engine (2) the front axle (3) . T avoid incorrect maneuvers with the hoist order not damage the radiator fins with the engine fan (1) Then join the two assemblies with the special retaining bolts and the necessary adjustment spacers the sump / cylinder block

1 Reposition the movable tool for dismantling tractors (2) under the Place a wooden block (1) the point contact between the tool and the

With the aid the place the engine (1) the tool (2) . Remove the lifting eyebolts previously fitted the rear the

Remove the fixed jack stand (3) previously positioned under the support the groove (1) the drive the front axle and the wooden plug (2)

14. Remove the fixed jack stand (1) previously fitted under the ballast support and the wooden wedges (2) locking the front

WLAPL4S10C132AA

Remove the old sealing paste from the two surfaces between the engine and clutch

16. Apply L OCTITE ® 518™ sealing compound the ing surfaces the engine and clutch

Put a wooden wedge under the right - hand rear Make sure that the hand brake fully applied and that all fixed and mobile stands are safely

18. The installation phase described here requires the presence two three workers use the specific movable tool for dismantling tractors move the gine / front axle assembly close the gearbox

19. the phase installing the engine / front axle bly the gearbox necessary push the front taking great care the end phase coupling over both the pipes and the cables / cal connections prevent crushing between the two bodies. Moreover , during this phase necessary turn the crankshaft with the aid the radiator cooling fan aid coupling between the sleeve and the drive

Secure both assemblies tightening all the bolts (1) locking the engine the gearbox case. WLAPL4S10C130A

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING

NOTE:

If there is no response to click on the link above, please download the PDF document first and then clickonit.

Disconnect the hoist Remove the jack stand (2) previously fitted under the clutch case (1) Retrieve the movable tool for dismantling tractors.

WLAPL4S10C129A

Refit the bracket (2) that supports the cab connectors (1) , cab power , and cup filter (3) Connect the pipe that joins the cup filter the mechanical priming pump the sediment filter .

23. the left - hand side, connect the cab power cable connector (1) Put the connector the maxi fuse box and lock with

WLAPL4S10C139A

Lay out the FPT interface - engine cable the chine. Reconnect the various connections. Secure the wiring with Reconnect the main electrical connections (1) , cab connections and power (2) , engine control unit nections (3) , fuse compartment (4) and sensors, and extensions according the tractor

MOIL13TR02889AB

Refit the starter motor (2) Then connect the ground cable the engine and battery Secure the ground cable with the bolt (3) the right - hand reconnect the positive battery cable and the wire harnesses the starter motor and the alternator Refit the shroud (1) the starter motor (2)

WLAPL4S10C135A

27. Refit the two supply and return lines the cab heater (1) and the pipe (3) inserted the lower sleeve ing from the expansion

MOIL13TR01739AB

Install and connect the hydraulic steering lines (1) Secure the hydraulic steering lines the front axle

Connect the tube (2) that connects the air cleaner the injection Secure the tube tightening the strap (1) .

Connect the tube (1) that goes from the air cleaner the Secure the tube tightening the - refit the hood support (2) Secure the hood support tightening the two bolts (3) .

31. Install the tube (1) that supplies the engine coolant the radiator Secure the tube tightening the Connect the tube (2) that returns the coolant the engine. Secure the tube.

MOIL13TR02877AB

Install the upper radiator guard (2) T ake care rectly position the electrical wire harnesses and tubes their seats between the guard itself and the radiator . T ighten the three retaining bolts (1) the radiator

MOIL13TR02942AA

Install the transmission oil filter (2) For machines with hydraulic lift and mid mount connect and secure the oil supply tubes the lift tributor and the mid mount valves (1) (if any) the connection point (3) .

MOIL13TR02888AB

Install the transmission oil supply tube (1) the filter (2) . Secure the supply tube using the straps.

MOIL13TR02887AB

36. Refit the transmission oil drain plug (1) . Refill with oil using a MOIL13TR00197AA

Refit the drive shaft together with the central support (1) and the retaining Insert the Adjust the shaft end play

Refit the guard the front axle control shaft (1) T ighten the front, central, and rear retaining bolts.

Using a hydraulic raise the rear the tractor move the mechanical jack stand under the left - hand reduction gear Put the wheel back into Fit the retaining nuts with a pneumatic