Engine - Engine and crankcase

Remove any supports positioned under the support bracket (1) the front Use a suitable tool fit the transmission the

Apply suitable sealing paste the coupling face (1) the transmission clutch bell.

15. Using a suitable tool, move the engine closer the

16. T ighten the four fastening screws (1) the left - hand side the clutch bell and tighten the prescribed

Repeat for the four fastening screws the right - hand side the clutch bell (1)

T ighten the four retaining nuts (1) the lower side the clutch bell and tighten the prescribed

19. Carefully clean all the parts contaminated any ing paste

Unclamp the chains the eyebolts and free the en-

21. Remove the two eyebolts used lift the engine.

22. Remove any supports positioned under the clutch bell the transmission

Remove any supports positioned under the sion

24. Retrieve and carefully clean the bracket (1) .

25. Correctly position the cable (2) .

Correctly position the bracket (1) its housing the

T ighten the two screws (3) which fix the bracket (1) place.

Carefully clean the area around the sleeve (1) the oil delivery pipe (2)

29. T ighten the sleeve (1) the oil delivery pipe (2) .

30. Retrieve the collar (3) and position correctly its

T ighten the fastening screw (4) the collar (2)

Carefully clean the area around the connector (1) the steering sensor

Correctly position the connector cable (1) the ing sensor

Connect the steering sensor connector (1)

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING

NOTE:

If there is no response to click on the link above, please download the PDF document first and then clickonit.

35. Carefully clean the area around the connector (1) the hydraulic fluid pressure sensor

Correctly position the connector cable (1) the hydraulic fluid pressure sensor .

37. Connect the connector (1) the hydraulic fluid sure sensor

MOIL16TR01460AA

Carefully clean the area around the connector (1)

Fasten the connector (1) the support bracket (2)

Connect the connector (1)

41. Carefully clean the area around the sleeve (1) the intermediate delivery pipe connected the sion oil filter

Connect the sleeve (1) the intermediate delivery pipe connected the transmission oil filter

T ighten the two screw collars (2) the sleeve (1) the intermediate delivery pipe connected the mission oil filter

T ighten the screw collar (3) fixing the sleeve (1) the intermediate delivery pipe connected the sion oil filter .

Carefully clean the area around the coupling (1) the intermediate delivery pipe connected the sion oil filter

Correctly connect the coupling (1) the intermediate delivery pipe connected the transmission oil filter

T ighten the coupling (1) the intermediate delivery pipe connected the transmission oil filter

MOIL16TR01458AA

MOIL16TR01457AA

MOIL16TR01456AA

48. Carefully clean the area around the coupling (1) the intermediate dif ferential oil delivery pipe the left - hand side the

49. Correctly connect the coupling (1) the intermediate dif ferential oil delivery pipe the left - hand side the

T ighten the coupling (1) the intermediate dif ferential oil delivery pipe the left - hand side the MOIL16TR01455AA

Carefully clean the area around the couplings (1) the intermediate delivery and return pipes the transmission oil exchanger

Correctly connect (1) the intermediate delivery and turn pipes the transmission oil exchanger

53. T ighten the couplings (1) the intermediate delivery and return pipes the transmission oil exchanger MOIL16TR01454AA

54. Use a suitable hydraulic lift and position under the oil sump the engine (only models with front axle SuperSteer™ )

MOIL16TR01451AA

Use a second suitable hydraulic lift and position under the swinging arm (1) (only models with front axle SuperSteer™ )

MOIL16TR01452AA

56. Push down the hydraulic lifts and correctly position the half bushes (1) the rear ball joint (2) (only els with front axle SuperSteer™ )

57. Position the snap ring fixing the half bushes (1) the rear ball joint (2) the swinging arm (3) (only models with front axle SuperSteer™ )

Refit the transmission drive shaft going from the transmission the front axle (only models with front axle SuperSteer™ ) - See Front drive shaft - Install (23.314) .

59. Refit the transmission drive shaft going from the mission the front axle (only models with standard front axle) - See Front drive shaft - Install (23.314)

Next operation:

Reattach the cab – See Cab and platform - Install (90.150)

T the transmission oil level - See T ransmission drive housing - Level make 18) Refit the front ballast - See Front ballast - Install (39.140)

Engine - Remove from transmission

W ARNING very careful avoid contact with hot fluids. fluid extremely hot, allow cool a moderately warm temperature before proceeding.

Burn hazard!

Failure comply could result death serious injury

W Arning

Hot surface possible!

W ait for all components cool before performing any

Failure comply could result death serious injury .

Caution

Hot area!

Use care when working near hot components. W ear protective gloves.

Failure comply could result minor moderate injury .

W Arning

Chemical hazard!

W0362A

W0251A

C0034A

When handling fuel, lubricants, and other service chemicals, follow the instructions.

W ear Personal Protective Equipment (PPE) not smoke use open Collect fluids proper containers. Obey all local and environmental regulations when disposing chemicals.

Failure comply could result death serious injury

Prior operation:

Remove the front ballast - See Front ballast - Remove (39.140)

Carefully clean the area around the central drain plug (1) the

Use a suitable container collect the transmission

Loosen the central drain plug (1) the transmission and drain the transmission oil.

Replace the central drain plug (1) the transmission.

T ighten the central drain plug (1) the

Carefully clean all the parts contaminated any ing hydraulic

Remove the operator platform – See Platform - Remove 10)

Remove the transmission drive shaft going from the transmission the front axle (only models with dard front axle) – See Front drive shaft - Remove

Remove the transmission drive shaft going from the transmission the front axle (only models with front axle SuperSteer™ ) - See Front drive shaft - Remove (23.314)

W0371A

10. Use a suitable hydraulic lift and position under the oil sump the engine (only models with front axle SuperSteer™ )

1 Use a second suitable hydraulic lift and position under the swinging arm (1) (only models with front axle SuperSteer™ )

12. Remove the snap ring fixing the half bushes (1) the rear ball joint (2) the swinging arm (3) (only models with front axle SuperSteer™ )

Push down the hydraulic lifts and extract the half bushes (1) the rear ball joint (2) (only models with front axle SuperSteer™ )

Carefully clean the area around the couplings (1) the intermediate delivery and return pipes the transmission oil exchanger

Use a suitable container collect the transmission

Loosen the couplings (1) the intermediate delivery and return pipes the transmission oil exchanger

17. Carefully clean the area around the coupling (1) the intermediate dif ferential oil delivery pipe the left - hand side the

18. Use a suitable container collect the transmission oil.

19. Loosen the coupling (1) the intermediate dif ferential oil delivery pipe the left - hand side the

Carefully clean the area around the coupling (1) the intermediate delivery pipe connected the sion oil filter

Use a suitable container collect the transmission

Loosen the coupling (1) the intermediate delivery pipe connected the transmission oil filter .

23. Carefully clean all the parts contaminated any ing hydraulic

24. Carefully clean the area around the sleeve (1) the intermediate delivery pipe connected the sion oil filter

Use a suitable container collect the transmission

26. Loosen the two screw collars (2) the sleeve (1) the intermediate delivery pipe connected the mission oil filter

Loosen the screw collar (3) fixing the sleeve (1) the intermediate delivery pipe connected the sion oil filter

Disconnect the sleeve (1) the intermediate delivery pipe connected the transmission oil filter

Carefully clean all the parts contaminated any ing hydraulic

Carefully clean the area around the connector (1) the steering sensor

31. Disconnect the steering sensor connector (1) .

32. Disconnect the connector cable (1) from the steering sensor