Construction Document Set by Victoria Smith

General Project Notes

Project Data

1. THE CONTRACT DOCUMENTS ARE THE INSTRUMENTS OF SERVICE AND SHALL REMAIN THE PROPERTY OF THE DESIGNER WHETHER THE PROJECT FOR WHICH THEY ARE PREPARED IS EXECUTED OR NOT. 2. "INSTALL" MEANS SUPPLIED BY OTHERS, TO BE INSTALLED BY CONTRACTOR. 3. "PROVIDE" MEANS FURNISH AND INSTALL, COMPLETE AND IN PLACE. 4. "TYPICAL" MEANS IDENTICAL FOR CONDITIONS NOTED. 5. DO NOT SCALE DRAWINGS, DIMENSIONS GOVERN. VERIFY DIMENSIONS WITH FIELD CONDITIONS, IF DISCREPANCIES ARE DISCOVERED BETWEEN FIELD CONDITIONS AND DRAWINGS OR BETWEEN DRAWINGS, CONTACT THE DESIGNER FOR RESOLUTION BEFORE PROCEEDING. 6. HORIZONTAL DIMENSIONS INDICATED ARE TO/FROM FINISHED FACE OF CONSTRUCTION, EXCEPT WHEN NOTED AS CENTERLINE (CL), DIMENSIONS ARE TO CENTERLINE OF FRAMING. 7. VERTICAL DIMENSIONS ARE FROM TOP OF FLOOR SLAB, EXCEPT WHERE NOTED TO BE FROM ABOVE FINISHED FLOOR, (A.F.F.). 8. CUT AND FIT COMPONENTS FOR ALTERATION OF EXISTING WORK AND INSTALLATION OF NEW WORK. PATCH DISTURBED AREAS TO MATCH ADJACENT MATERIALS AND FINISHES. 9. PATCH AND REPAIR ALL FIREPROOFING DAMAGED OR REMOVED DURING PERFORMANCE OF THE WORK. FIREPROOF NEW PENETRATIONS REQUIRED BY THE WORK AND EXISTING PENETRATIONS IN EXPOSED PLENUM AREAS. 10. CONTRACTOR & SUB-CONTRACTORS SHALL COORDINATE THE LAYOUT AND EXACT LOCATIONS OF ALL PARTITIONS, DOORS, ELECTRICAL/TELEPHONE OUTLETS AND LIGHT SWITCHES WITH THE DESIGNER BEFORE PROCEEDING WITH CONSTRUCTION. 11. CONTRACTOR SHALL PROVIDE MANUFACTURER'S SPECIFICATIONS, INSTALLATION INSTRUCTIONS, SHOP DRAWINGS AND SAMPLES FOR REVIEW AND APPROVAL OF ALL MATERIALS AND METHODS TO BE USED PRIOR TO ORDERING OR PROCEEDING WITH THE WORK.

PROJECT DESCRIPTION: THIS PROJECT IS A PARTIAL RENOVATION TO THE SECOND FLOOR AT THE NORTH SIDE OF BURRUSS HALL. THERE IS NO CHANGE OF USE, INCREASE IN AREA, OR ACTIVITY FUNCTIONS. APPLICABLE CODES AND REFERENCE STANDARDS: INTERNATIONAL BUILDING CODE (IBC 2012 EDITION) NATIONAL ELECTRIC CODE (NEC) AMERICANS WITH DISABILITIES ACT (ADA) USE GROUP CLASSIFICATION (EXISTING SPACE): E (EDUCATION) A (ASSEMBLY) USE GROUP CLASSIFICATION (PROPOSED SPACE):

Virginia Tech Interior Design

A (ASSEMBLY) * NOTE: THERE IS NO CHANGE OF USE CONSTRUCTION TYPE: 2A NON-COMBUSTIBLE, PROTECTED OCCUPANT LOADS: EDUCATION AREAS CALCULATED AT OCCUPANT ASSEMBLY AREAS CALCULATED AT OCCUPANT

20 SQ.FT. PER 15 SQ.FT. PER

OCCUPANT LOAD: PROPOSED SPACE, SECOND FLOOR:

BURRUSS OPEN OFFICE

CODE: 482 ACTUAL: 130

PROJECT SQUARE FOOTAGE: PROPOSED SPACE, SECOND FLOOR

9,550 NET SQ.FT.

12. CONTRACTOR TO FOLLOW MANUFACTURER'S RECOMMENDED SPECIFICATIONS AND INSTALLATION PROCEDURES. IF THESE ARE CONTRARY TO THE CONTRACT DOCUMENTS, CONTRACTOR SHALL NOTIFY THE DESIGNER, IN WRITING IMMEDIATELY, TO RESOLVE DISCREPANCIES PRIOR TO PRECEEDING.

VIRGINIA TECH

13. CONTRACTOR SHALL ORDER AND SCHEDULE DELIVERY OF MATERIALS IN AMPLE TIME TO AVOID DELAYS IN CONSTRUCTION. IF AN ITEM IS FOUND TO BE UNAVAILABLE, CONTRACTOR SHALL NOTIFY DESIGNER IMMEDIATELY TO ALLOW DESIGNER A REASONABLE AMOUNT OF TIME TO SELECT A REASONABLE SUBSTITUTE. 14. THE FINISHED WORK SHALL BE FIRM, WELL ANCHORED, IN TRUE ALIGNMENT, PLUMB, LEVEL, WITH SMOOTH, CLEAN, UNIFORM APPEARANCE WITHOUT WAVES, DISTORTIONS, HOLES, MARKS, CRACKS, STAINS, OR DISCOLORATION. JOINTING SHALL BE TIGHT FITTING, NEAT AND WELL SCRIBED. THE FINISH WORK SHALL NOT HAVE EXPOSED UNSIGHTLY ANCHORS OR FASTENERS AND SHALL NOT PRESENT HAZARDOUS, UNSAFE CORNERS. ALL WORK SHALL HAVE THE PROVISION FOR EXPANSION CONTRACTION, AND SHRINKAGE AS NECESSARY TO PREVENT CRACKS, BUCKLING AND WARPING DUE TO TEMPERATURE AND HUMIDITY CONDITIONS. 15. CONTRACTOR SHALL COMPLY WITH ALL BASE BUILDING REQUIREMENTS AND DESIGN CRITERIA. 16. ALL WORK SHALL COMPLY WITH THE APPLICABLE CODES, AMENDMENTS, RULES, REGULATIONS, ORDINANCES, LAWS, ORDERS, APPROVALS, ETC., THAT ARE REQUIRED BY PUBLIC AUTHORITIES. IN THE EVENT OF CONFLICT, THE MOST STRINGENT REQUIREMENTS SHALL COMPLY. REQUIREMENTS INCLUDE, BUT ARE NOT LIMITED TO THE CURRENT APPLICABLE EDITIONS OR PUBLICATIONS OF THE FOLLOWING (OR OTHERWISEE NOTED): A. INTERNATIONAL BUILDING CODE (IBC 2012 EDITION) B. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) C. NATIONAL ELECTRIC CODE (NEC) D. INTERNATIONAL PLUMBING CODE (IPC 2009 EDITION) E. INTERNATIONAL MECHANICAL CODE (IMC 2009 EDITION) F. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) G. AMERICANS WITH DISABILITIES ACT (ADA) H. LOCAL MUNICIPAL ORDINANCES AND AMENDEMENTS TO THE CODES

No. Description

SHEET INDEX SHEET # A100 A101 A102 A103 A104 A105 A106 A107 A108 A109 A110 A111 A112 A113 A114 A115

Date

SHEET NAME COVER SHEET FIRE + LIFE SAFETY PLAN EXISTING PLAN DEMOLITION PLAN PLAN ENLARGED PLAN INTERIOR SECTIONS WALL SECTIONS INTERIOR ELEVATIONS INTERIOR WALL DETAILS MILLWORK DETAILS FINISH PLAN FURNITURE PLAN POWER + DATA PLAN RCP ENLARGED RCP

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

COVER SHEET

AREA OF NEW CONSTRUCTION BURRUSS HALL, ROOM 224A

SITE PLAN BURRUSS HALL, ROOM 224A

PROJECT NORTH

VICINITY MAP VIRGINIA TECH, BLACKSBURG, VIRGINIA

TRUE NORTH PROJECT NORTH

A100

WALL LEGEND EXISTING WALL

EXISTING FIRE WALL

Virginia Tech Interior Design

AREA LEGEND

EXISTING OFFICE [E (EDUCATION)]

1279 SQ. FT.

BURRUSS OPEN OFFICE

EXISTING STUDIO [E (EDUCATION)]

6619 SQ. FT.

OPEN OFFICE [A (ASSEMBLY)]

1317 SQ. FT.

TOILET ROOM.

335 SQ. FT.

VIRGINIA TECH

No. Description

Date

AREA OF NEW CONSTRUCTION

Consultant Address Address Address Phone

2 Consultant Address Address Address Phone

Consultant Address Address Address Phone

3 EGRESS (BELOW)

DOWN

EGRESS (BELOW)

Date

02 MAY 2017

Project Number Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

FIRE + LIFE SAFETY PLAN

FIRE + LIFE SAFETY PLAN PROJECT NORTH

1/8" = 1'-0"

A101

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

No. Description

Date

Consultant Address Address Address Phone

2 Consultant Address Address Address Phone

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

EXISTING PLAN

SECOND FLOOR EXISTING PLAN 1/8" = 1'-0"

PROJECT NORTH

A102

Virginia Tech Interior Design

BURRUSS OPEN OFFICE WALL LEGEND

EXISTING WALL

WALLS TO BE DEMOLISHED

VIRGINIA TECH

No. Description

Date

Consultant Address Address Address Phone

2 Consultant Address Address Address Phone

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

DEMOLITION PLAN

SECOND FLOOR DEMOLITION PLAN PROJECT NORTH

1/8" = 1'-0"

A103

3' - 6" 0' - 7"

3' - 4"

2' - 4"

0' - 7"

TEMPERED GLASS. DORMA MANET HAREDWARE. PASSAGE SET.

7' - 6"

DORMA MANET HARDWARE. PASSAGE SET.

3' - 3"

SOLID MAPLE DOOR. SATIN VARNISH FINISH.

0' - 7"

7' - 0"

7' - 2"

RAW METAL TRACK FRAME. SATIN CLEAR COAT FINISH.

Virginia Tech Interior Design

SOLID DOOR

1/4" = 1'-0"

SLIDING DOOR 1/4" = 1'-0" 6' - 0"

6' - 4" 3' - 2"

2' - 0"

3' - 6" 7' - 4"

DOOR NUMBER

RAW METAL FRAME. SATIN CLEAR COAT FINISH.

101 DOOR TAG

FIRE RATED WIRE GLASS

1/4" = 1'-0"

2' - 0"

BURRUSS OPEN OFFICE

DORMA CL800 HARDWARE. LOCK SET. 3' - 4"

GLASS DOOR

3' - 0"

6' - 10"

3' - 2 3/4"

DORSA FSW HARDWARE. PASSAGE SET.

7' - 6"

TEMPERED GLASS.

7' - 5"

7' - 6"

RAW METAL LOW PROFILE FRAME WITH CLEAR SILICON JOINT. SATIN CLEAR COAT FINISH.

3' - 0"

FIRE RATED METAL DOOR WITH MAPLE VENEER SATIN VARNISH FINISH.

3' - 3"

3' - 2"

ENTRY DOOR 1/4" = 1'-0"

Door Schedule DOOR NO. 01 02 03 04 05 06

ROOM NAME OPEN OFFICE SMALL CONF SMALL CONF LARGE CONF M TOILET W TOILET

GLASS TYPE FIRE RATED WIRE TRANSPARENT TEMPERED TRANSPARENT TEMPERED TRANSPARENT TEMPERED N/A N/A

MATERIAL MTL/MPL MAPLE MAPLE GLASS MAPLE MAPLE

FINISH SATIN SATIN SATIN GLOSS SATIN SATIN

WIDTH 6' - 0" 3' - 4" 3' - 4" 6' - 4" 3' - 0" 3' - 0"

HEIGHT 7' - 4" 7' - 6" 7' - 6" 7' - 5" 7' - 0" 7' - 0"

THICKNESS 0' - 1 3/4" 0' - 1 5/8" 0' - 1 5/8" 0' - 0 1/2" 0' - 1 3/4" 0' - 1 3/4"

MATERIAL METAL MAPLE MAPLE METAL METAL METAL

FINISH SATIN SATIN SATIN SATIN SATIN SATIN

HDWR GROUP DORMA CL800 DORMA MANET DORMA MANET DORMA FSW DORMA CL800 DORMA CL800

SECURITY LOCK SET PASSAGE PASSAGE PASSAGE PASSAGE PASSAGE

FIRE RATING 45 MINUTES NR NR NR NR NR

COMMENTS EGRESS HDWR, SWING INTO EGRESS CORRIDOR SLIDING DOOR LOCATION INSIDE SMALL CONF SLIDING DOOR LOCATION INSIDE SMALL CONF SWING DIRECTION INDICATED ON PLAN SWING DIRECTION INDICATED ON PLAN SWING DIRECTION INDICATED ON PLAN

VIRGINIA TECH

No. Description

Date

Consultant Address Address Address Phone

2 A105

05 03

Consultant Address Address Address Phone

06 1 A105

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

PLAN

SECOND FLOOR PLAN 1/8" = 1'-0"

PROJECT NORTH

A104

Virginia Tech Interior Design

WALL LEGEND

FLOOR PLAN SYMBOLS DRAWING NUMBER

A1.01

BURRUSS OPEN OFFICE

EXISTING WALL

1 SHEET NUMBER

INTERIOR ELEVATION

DRAWING NUMBER 1

NEW METAL STUD WALL

A1.01

SHEET NUMBER

BUILDING SECTION

DRAWING NUMBER

NEW CURTAIN WALL

A1.01

SHEET NUMBER

WALL SECTION

VIRGINIA TECH

No. Description

C 1

A106

A107 3

9' - 6 3/4"

16' - 3"

9' - 3 1/2" 8' - 7 1/4"

92 .0 0°

88 .0 0°

5 A106 3 5' - 2 1/2"

5' - 1 1/2" 23' - 11"

23' - 2 1/4"

22' - 7 3/4"

21' - 7 1/2"

A108

Consultant Address Address Address Phone

A104 5' - 5"

3' - 6 1/2"

4 7

1' - 6"

5' - 5 1/2"

8' - 9 1/4"

A108

6' - 10 3/4"

2' - 0"

A104

7' - 8 3/4"

5' - 4 1/4"

2' - 5 1/4"

18' - 10 1/4"

16' - 9"

A106

Consultant Address Address Address Phone

A104 A108

A104

A107

3' - 6 1/4"

A106 12' - 4 1/2"

15' - 1 3/4"

Date

5' - 0"

A110

2' - 0 1/2"

2' - 4"

2' - 7"

1' - 1"

Consultant Address Address Address Phone

3 10' - 3 1/4"

5' - 10"

11' - 5 3/4"

Date

A107 12' - 0"

2' - 6 1/2"

22' - 6 1/2"

2' - 9"

23' - 2 3/4"

13' - 3"

02 MAY 2017

Project Number Drawn By

53' - 1"

Checked By

2017_0001 T.SMITH M. WAGNER

ENLARGED PLAN

ENLARGED OPEN OFFICE PLAN 1/4" = 1'-0"

ENLARGED TOILET ROOM PLAN 1/4" = 1'-0"

PROJECT NORTH

A105

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

WEST-EAST SECTION

1/4" = 1'-0"

Date

9' - 11"

9' - 6"

10' - 1"

No. Description

NORTH - SOUTH SECTION 1/4" = 1'-0"

Consultant Address Address Address Phone

NORTH - SOUTH SECTION

Consultant Address Address Address Phone

1/4" = 1'-0"

2 A110 7' - 10".

7' - 10"

1' - 3 1/4"

Consultant Address Address Address Phone

02 MAY 2017

Project Number 7' - 6"

Drawn By Checked By 2' - 6"

8' - 7"

9' - 6"

9' - 11"

10' - 1"

Date

2017_0001 T.SMITH M. WAGNER

INTERIOR SECTIONS

WEST-EAST SECTION 1/4" = 1'-0"

SOUTH - NORTH SECTION 1/4" = 1'-0"

A106

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

No. Description

TOP OF SLAB

BOTTOM OF SLAB

Date

0' - 5"

DOUBLE 2X6 METAL STUD TOP PLATE.

COMPOUND CEILING GYPSUM BOARD ON 3 5/8" METAL FRAME.

NEW OR EXISTING WALL. INSIDE FACE TO BE PAINT FINISH.

1/2" GYPSUM WALL BOARD. TYPICAL. EXTEND BEYOND CEILING. INSIDE FACE TO BE PAINT FINISH.

STUD LENGTH VARIES

2' - 0"

1/2" GYPSUM WALL BOARD. TYPICAL. EXTEND BEYOND CEILING. INSIDE FACE TO BE PAINT FINISH.

COMPOUND CEILING GYPSUM BOARD ON 3 5/8" METAL FRAME.

2' - 0 1/4"

DOUBLE 2X6 METAL STUD TOP PLATE.

3/4" PLYWOOD SHEATHING. TYPICAL. ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

1/2" PLYWOOD SHEATHING. TYPICAL.

1/2" FINISH GRADE PLYWOOD MILLWORK ASSEMBLY. SURFACE TO BE MAPLE VENEER WITH SATIN VARNISH FINISH.

1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

2X6 METAL STUD @ 16" O.C. DOUBLE 2X6 METAL STUD BASE PLATE. METAL SHADOW REVEAL PANEL CLIP. SEE SHEET A109 FOR DETAILS.

ADDITIONAL 2X4 METAL STUDS FOR CANTILEVER REINFORCEMENT.

Consultant Address Address Address Phone

7' - 0"

2X4 METAL STUD @ 16" O.C. 1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

5' - 0"

4' - 11 3/4"

DOUBLE 2X4 METAL STUD EDGE PLATE.

Consultant Address Address Address Phone

DOUBLE 2X4 METAL STUD EDGE PLATE. ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS FLOOR TO SLAB. TYPICAL.

ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

2X4 METAL STUD @ 16" O.C.

2X4 METAL STUD @ 16" O.C. ADDITIONAL 2X4 METAL STUDS FOR CANTILEVER REINFORCEMENT.

ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

DOUBLE 2X6 METAL STUD TOP PLATE.

1/2" GYPSUM WALL BOARD. TYPICAL. INSIDE FACE TO BE PAINT FINISH.

2X4 METAL STUD BASE PLATE.

STUD LENGTH VARIES

4" CONTINUOUS METAL WALL BASE.

3/4" PLYWOOD SHEATHING. TYPICAL.

2' - 2 1/4"

2 A109

2' - 2"

METAL SHADOW REVEAL PANEL CLIP. SEE SHEET A109 FOR DETAILS.

2X6 METAL STUD @ 16" O.C.

4" CONTINUOUS METAL WALL BASE. 0' - 4"

0' - 4"

FINISHED FLOOR

TYP. WOOD PANEL WALL 1" = 1'-0"

1 A109

TYP. METAL PANEL WALL 1" = 1'-0"

Date

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

WALL SECTIONS 4" CONTINUOUS METAL WALL BASE.

FINISHED FLOOR

0' - 4"

2X6 METAL STUD BASE PLATE.

Consultant Address Address Address Phone

FINISHED FLOOR

BOX WINDOW SECTION 1" = 1'-0"

A107

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

No. Description TEMPERED CURTAIN WALL GLAZING @ CONFERENCE ROOM WALL.

SEE SHEET 110 FOR CEILING CANOPY DETAILS.

1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

ELEVATION 1/4" = 1'-0"

1/2" FINISH GRADE PLYWOOD PANEL. SURFACE TO BE MAPLE VENEER WITH SATIN VARNISH FINISH.

EXISTING STOREFRONT WINDOW

Consultant Address Address Address Phone

2' - 2" 0' - 4"

EXISTING WINDOW.

Consultant Address Address Address Phone

5' - 0"

9' - 11"

2' - 0"

0' - 5"

1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

Date

ELEVATION

1/4" = 1'-0" 1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

TEMPERED CURTAIN WALL GLAZING @ BOX WINDOW.

4" Continuous Metal Wall Base.

1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH.

ELEVATION 1/4" = 1'-0"

1/2" FINISH GRADE PLYWOOD PANEL. SURFACE TO BE MAPLE VENEER WITH SATIN VARNISH FINISH.

EXPOSED GYPSUM WALL BOARD TO BE PAINT FINISH.

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

INTERIOR ELEVATIONS

ELEVATION 1/4" = 1'-0"

A108

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

No. Description

0' - 1 1/4"

Date

0' - 1 1/2" 0' - 0 3/4"

"RETAINER" CLIP BY FRYE REGLET.

1/2" FINISH GRADE PLYWOOD MILLWORK ASSEMBLY. SURFACE TO BE MAPLE VENEER WITH SATIN VARNISH FINISH.

ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

2X4 METAL STUD @ 16" O.C.

ADDITIONAL 2X4 METAL STUDS FOR CANTILEVER REINFORCEMENT.

ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS FLOOR TO SLAB. TYPICAL.

Consultant Address Address Address Phone

DOUBLE 2X6 METAL STUD TOP PLATE.

2X4 METAL STUD @ 16" O.C. 1/2" MDF WALL PANEL WITH COMMERCIAL GRADE FLAT METAL SURFACE FINISH. ACOUSTIC BATT INSULATION. FILL BETWEEN STUDS. TYPICAL.

1/2" GYPSUM WALL BOARD. TYPICAL.

Consultant Address Address Address Phone

2X6 METAL STUD @ 16" O.C.

1/2" PLYWOOD SHEATHING. TYPICAL.

1/2" GYPSUM WALL BOARD. TYPICAL.

3/4" PLYWOOD SHEATHING. TYPICAL.

Consultant Address Address Address Phone

"BASE" CLIP BY FRYE REGLET.

Date METAL PANEL SPACER EDGE DETAIL.

02 MAY 2017

Project Number METAL PANEL SPACER EDGE DETAIL.

2X4 METAL STUD BASE PLATE.

2X6 METAL STUD BASE PLATE. 4" CONTINUOUS METAL WALL BASE.

4" CONTINUOUS METAL WALL BASE.

Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

INTERIOR WALL DETAILS

WOOD PANEL WALL DETAIL 3" = 1'-0"

BOX WINDOW WALL DETAIL 3" = 1'-0"

A109

CANOPY MILLWORK 3D VIEW Virginia Tech Interior Design

BURRUSS OPEN OFFICE 7' - 10"

7' - 10"

1' - 3 3/4"

1' - 0 3/4"

0' - 2"

7' - 10"

1' - 0 3/4"

7' - 10"

VIRGINIA TECH

8' - 6 1/2"

Date

1' - 0 3/4"

1' - 0 3/4".

0' - 2"

1' - 0 3/4"

0' - 2"

1' - 0 3/4"

No. Description

FIXTURE LENS TO BE 1/4" FROSTED GLASS. LENS TO BE RECESSED +1" AFF WHEN MATCHED WITH ITS ADJACENT LENGTH MAPLE PANEL GROUP.

CEILING CANOPY MODULES TO BE 1/2" FINISH GRADE PLYWOOD ASSEMBLY. MAPLE VENEER SURFACE WITH SATIN VARNISH FINISH. SEE SECTION 2 ON SHEET A106 FOR VARYING CEILING HEIGHTS.

Consultant Address Address Address Phone

CANOPY MILLWORK RCP 3/4" = 1'-0" CANOPY MODULE CLIP SYSTEM TO ATTACH TO CEILING STRUCTURE ABOVE. CEILING STRUCTURE ABOVE.

Consultant Address Address Address Phone 2' - 6"

88 .7 8°

1' - 10 1/4" TYP

0' - 4 1/4"

8° .7 8 8

1' - 10 1/4" TYP

91 .2 2°

0' - 6 1/4"

91 .2 2°

0' - 4 1/4"

0' - 6 1/4"

88 .7 8°

1' - 10 1/4" TYP

6° 5.3 10

° 78 . 88

2° .2 91

0' - 4 1/4"

1' - 10 1/4" TYP.

4° .6 4 7

CANOPY MILLWORK SECTION 3/4" = 1'-0" CEILING CANOPY MODULES TO BE SEPERATED WITH 1/4" METAL SPACERS.

CEILING CANOPY MODULE SIDE PANEL. MODULES TO BE CLOSED ON ALL SIX SIDES FOR STRUCTURAL INTEGRITY.

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

MILLWORK DETAILS

CANOPY MILLWORK ELEVATION 3/4" = 1'-0"

A110

Virginia Tech Interior Design

BURRUSS OPEN OFFICE AREA LEGEND

POLISHED CONCRETE. OPEN OFFICE.

565 SQ. FT.

VIRGINIA TECH SOLID MAPLE. OPEN OFFICE.

No. Description

697 SQ. FT.

Date

6"X6" CERAMIC TILE. TOILET ROOM. 334 SQ. FT.

POLISHED CONCRETE FLOOR. ACRYLIC SEALANT FINISH

1' - 6"

SOLID MAPLE FLOOR. SATIN VARNISH FINISH.

Consultant Address Address Address Phone

SOLID MAPLE FLOOR. SATIN VARNISH FINISH.

Consultant Address Address Address Phone

6" x 6" CERAMIC TILE. FLAT FINISH.

8' - 6 1/4"

20' - 11"

SOLID MAPLE FLOOR. SATIN VARNISH FINISH.

3' - 2 1/4"

Consultant Address Address Address Phone

3 9' - 3 1/2"

40' - 7"

Date

1' - 6"

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

FINISH PLAN

SECOND FLOOR FINISH PLAN 1/8" = 1'-0"

PROJECT NORTH

A111

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

FURNITURE SCHEDULE DESCRIPTION AERON WORK CHAIR

Manufacturer HERMAN MILLER, INC. HERMAN MILLER, INC. GLOBAL SYSTEMS GLOBAL SYSTEMS GLOBAL SYSTEMS HAWORTH HAWORTH HAWORTH HAWORTH

GOETZ SOFA MAPLE TABLE - 36"x72" MAPLE TABLE - 36"x96" MAPLE TABLE - 60"x212" Q_BIC TABLE VERY CONFERENCE CHAIR LTB BENCH RESIDE WORKSURFACE - 30"x66"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0" 3' - 1 3/4"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

3' - 0"

5' - 5"

1 129 3 128

LOCATED IN OPEN OFFICE. LOCATED IN EXISTING OFFICES, AND EXISTING STUDIO. LOCATED IN OPEN OFFICE. LOCATED IN EXISTING OFFICES, AND EXISTING STUDIO.

VIRGINIA TECH

No. Description

Date

6' - 0"

3' - 1"

6' - 0"

2' - 6"

6' - 6"

5' - 6" 2' - 0"

4' - 7"

1' - 1 1/2"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

4' - 0"

5' - 0"

8' - 2 1/2" 7' - 1"

Consultant Address Address Address Phone

1' - 1 1/2"

3 2' - 4"

Consultant Address Address Address Phone

5' - 6"

4' - 8"

4' - 7"

5' - 0"

3' - 2 1/4"

3' - 0"

8' - 0" 5' - 5"

VERY CONFERENCE CHAIR. HAWORTH.

3' - 7"

5' - 6"

3' - 1 1/4"

3' - 6 3/4" 3' - 0" 3' - 0"

3' - 0"

17' - 8"

LOCATED IN OPEN OFFICE, AND EXISTING STUDIO.

5' - 6" 3' - 7 1/2" 3' - 9"

3' - 6"

6' - 8 1/4"

3' - 10 1/4"

5' - 6" 4' - 8 1/2"

5' - 0"

17' - 8"

3' - 7"

4' - 0" 2' - 6"

LOCATED IN OPEN OFFICE.

RESIDE WORKSURFACE - 66"X30". HAWORTH.

5' - 6"

4' - 4"

5' - 6" 3' - 8 1/2" 3' - 8"

8' - 11"

3' - 5 7/8" 5' - 0"

LOCATED IN OPEN OFFICE.

5' - 0"

5' - 6"

5' - 10 1/2"

5' - 0"

AERON WORK CHAIR. HERMAN MILLER, INC. 3' - 1 3/4" 5' - 0"

5' - 10 1/2"

4' - 0"

LOCATED IN OPEN OFFICE.

MAPLE TABLE - 60"X212". GLOBAL SYSTEMS.

VERY CONFERENCE CHAIR. HAWORTH. 5' - 0"

5' - 6"

RESIDE WORKSURFACE - 66"X30". HAWORTH.

Type Comments LOCATED IN OPEN OFFICE, AND EXISTING STUDIO.

4' - 9 1/2"

Count

2' - 6"

7' - 1"

2' - 4"

AERON WORK CHAIR. HERMAN MILLER, INC.

0' - 6"

Consultant Address Address Address Phone

2' - 6" 4' - 0"

Date

02 MAY 2017

Project Number Drawn By Q-BIC TABLE. HAWORTH.

AERON WORK CHAIR. HERMAN MILLER, INC. MAPLE TABLE - 60"X212". GLOBAL SYSTEMS.

GOETZ SOFA. HERMAN MILLER, INC. LTB BENCH. HAWORTH.

AERON WORK CHAIR. HERMAN MILLER, INC.

MAPLE TABLE 36"X96". GLOBAL SYSTEMS.

MAPLE TABLE - 36"X72" GLOBAL SYSTEMS.

SECOND FLOOR FURNITURE PLAN 1/8" = 1'-0"

Checked By

AREA RESERVED FOR EXISTING LAB PRINTERS.

2017_0001 T.SMITH M. WAGNER

FURNITURE PLAN PROJECT NORTH

A112

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

POWER & DATA SYMBOLS

QUADRAPLEX RECEPTACLE

DATA RECEPTACLE

VIRGINIA TECH

INSTALL @ 18" AFF UNLESS OTHERWISE NOTED

No. Description

INSTALL @ 18" AFF UNLESS OTHERWISE NOTED

Date

Consultant Address Address Address Phone

INSTALL POWER AND DATA RECEPTACLE @ 34" AFF.

2 Consultant Address Address Address Phone

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number Drawn By Checked By

2017_0001 T.SMITH M. WAGNER

POWER + DATA PLAN

SECOND FLOOR POWER + DATA PLAN 1/8" = 1'-0"

PROJECT NORTH

A113

Virginia Tech Interior Design

BURRUSS OPEN OFFICE

VIRGINIA TECH

No. Description

Date

Consultant Address Address Address Phone

2 A115

2 Consultant Address Address Address Phone 1 A115

Consultant Address Address Address Phone

Date

02 MAY 2017

Project Number

2017_0001

Drawn By

T.SMITH

Checked By

M. WAGNER

RCP

SECOND FLOOR RCP PROJECT NORTH

1/8" = 1'-0"

A114

Virginia Tech Interior Design

LIGHTING LEGEND 96" (48" x 2) CONCEALED FLUORESCENT STRIP LIGHT

BURRUSS OPEN OFFICE

6" RECESSED COMPACT FLUORESCENT DOWNLIGHT. CEILING MOUNTED EXIT SIGN (LIGHTED). ARROWS INDICATE DIRECTION OF EXIT. 2' x 2' SUPPLY AIR GRILLE.

VIRGINIA TECH

No. Description

2' x 2' RETURN AIR GRILLE.

Date

SWITCH.

C D

RETURN AIR GRILLE. TYPICAL.

SUPPLY AIR GRILLE. TYPICAL.

1' - 5 3/4"

GWB BULKHEAD FROM CEILING @ 9'-6" AFF.

GWB

9'-11" AFF

6' - 6 3/4"

9'-11" AFF

6' - 0"

Consultant Address Address Address Phone

3' - 9 3/4"

MAPLE ACT

9'-0" AFF

SEE SHEET 110 FOR CEILING CANOPY DETAILS

2' - 9"

6' - 0"

3' - 2 1/8"

6' - 0"

0' - 9 3/4"

MAPLE ACT

6' - 0"

8' - 4 3/4"

6' - 0" 2' - 0"

6' - 0"

GWB

1' - 6"

Consultant Address Address Address Phone

3 Date

1' - 5 1/4"

6' - 0"

96" (48" X 2) CONCEALED FLUORESCENT STRIP LIGHT BEHIND GLASS LENS. SEE SHEET 110 FOR GLASS LENS DETAILS.

4' - 6"

0' - 5 1/2"

6' - 0"

9'-11" AFF

5' - 5 1/2"

6' - 0"

MAPLE ACT

6" RECESSED DOWNLIGHT. TYPICAL.

2' - 3"

9'-11" AFF

2' - 3"

2' - 0"

3' - 10"

6' - 0"

MAPLE ACT

2' - 0"

MAPLE ACT 10'-1" AFF

0' - 9 3/4"

0' - 5 1/2"

2' - 6"

2' - 9"

4' - 0"

2' - 0"

20' - 11"

2' - 6"

4' - 0"

6' - 0"

2' - 9"

6' - 0"

GWB 10'-1" AFF

4' - 0"

4' - 6"

3' - 6"

GWB 10'-1" AFF

GWB

4' - 0"

2' - 0"

3' - 6"

3' - 2"

GWB 9'-11" AFF

2' - 9"

1' - 6"

7'-6" AFF

1' - 6"

3 A110 9' - 0"

CEILING MOUNTED EXIT SIGN (LIGHTED). ARROWS INDICATE DIRECTION OF EXIT

02 MAY 2017

Project Number

2017_0001

Drawn By

1' - 6"

T.SMITH

Checked By

M. WAGNER

ENLARGED RCP

ENLARGED OPEN OFFICE RCP 1/4" = 1'-0"

ENLARGED TOILET ROOM RCP 1/4" = 1'-0"

PROJECT NORTH

A115