Instruments for surgery (OMS) and dental implantists
Special denticulations are the base for well sharping and smoothly instruments which afford an untraumatic working at the jaw-bone – the instruments could be handled easily and they won’t clog so speedily. .... agreeable for health worker and patients! A special tungsten carbide alloying with extreme heat conductance assure a cool grinding. … agreeable for the patients and beneficial for the healing process! Advice: The instruments HF113 & HF113Z with working part diameter 040 and 050 are especially suited to the smoothness of the pine comb.
HF 118 021 HP
HF 119 016 HP
HF 113Z 050 HP
HF 113 050 HP
HF 113Z 040 HP
HF 113 040 HP
HF 113Z 035 HP
HF 113 035 HP
HF 113Z 031 HP
HF 113 031 HP
HF 113Z 027 HP
HF 113 027 HP
HF 113Z 023 HP
HF 113 023 HP
for workings at the jaw-bone
Recommended rotary instruments Tungsten carbide bone cutters figure : HF 113 working part Ø : 023*, 027, 031, 035, 040, 050 shank : RAL/RAXL/HP/HPL * 023 not available in HPL Tungsten carbide bone cutters, serrated figure : HF 113 Z working part Ø : 023, 027, 031, 035, 040, 050 : RAL/RAXL/HP shank similarly the figures HF 118 021 RAXL/HP HF 119 016 FGXL/RA/RAL/RAXL/HP HF 119 A 014 RAL/HP (fig. see below)
for the bone-splitting
Technology and instruments Conditional upon the minor pine comb width it is important for the following works with the chisel to make an minimal invasive and accurate guiding transection with a diamond disc with the diameter 8-9mm. In case of a bone density of D2 or D3 it is perhaps reasonable to make discharge cuts with the above named diamond discs. This is necessary to avoid an uncontrolled fraction. ��� � ������������������������ ��� � ������������������������� �������� � ��������������� ������ � �����������������
HF 119 A 014 HP
Indications In case of a minor bone amylum until 3mm the jawbone could be split in the middle and could be expanded with special chisel – so called Osteotome. The emerged bone split between buccal and lingual as the case may be buccal and palatinal lamella could then take the implant up.
TD 090 F 025 HP
Bone-splitting = aneurysma of the pine comb for 2-5mm in the mandible as well as the maxilla for the insertion of implants.
Alternative and additional you also could use tungsten carbide cutters. Recommended rotary instruments TURBO-diamond discs TD 080 F 025 HP oder TD 090 F 025 HP Tungstene carbide bone cutters HF 119 A 014 RAL/HP
Spezial information
�������
������������ ���������������������������� �������
Instruments for surgery (OMS) and dental implantists
for teeth and root separation Well sharping and smoothly diamond instruments for teeth and root seperation, hemisections, … The special geometry („grooving“) of the instruments counteract the clogging reliable.
Tungsten carbide bone cutters (fig. see in front) HF 119 016 FGXL/RA/RAL/RAXL/HP
KF D 10 21 FG
KF D 10 18 FG
KF D 10 16 FG
Recommended rotary instruments Diamond coated root seperator KFD 10 16 FG/RAL/HP KFD 10 18 FG/RAL/HP KFD 10 21 FG/RAL/HP
for the sine lift Sine lift = is a special operation technique to thicken the osseous maxillary sinus ground. Important! This is exclusive for the maxilla front tooth area. Indications In consequence of the expansion of the aerial-full maxillary sinus in the molar range of the maxilla and after long-time absence of teeth in all sections of the jaw (jaw-bone atrophy!) the existing bone do not suffice for the implant.
With it there originates the desired thickened implant camp. Recommended rotary instruments Diamond instruments figures ............. : 801 working part Ø : 023, 025, 029, 035, 042 grid ................. : C shank .............. : HP
The vertical osseous height is too minor so that the inserted implant would extend into the maxillary sinus. In these cases the implant camp must be increased! Advice! Only in the mandible front tooth area is always enough bone available for the implants. Technology and instruments
Now the so resulted hollow cavity is filled in with own bone or foreign bone or synthetic osseous substitute material which is substituted in the course of months diminished / absorbed by newly establishing bone.
801 042 C HP
801 035 C HP
801 029 C HP
The artificially created lid will then be clapped inwards on top (lifting) together with the „Schneidersche Membran” (membrane around the aerial-full maxillary sinus).
801 025 C HP
The thin and lateral maxillary sinus septum will be uncovered by opening the gingiva. Afterwards a 1-2mm area will be weaken by an circumferential line with all-shaped diamond instruments. The upper line will be perforated (predetermined breaking point ) so that it could be pushed in easily.
801 023 C HP
Direct sine lift
Indirect sine lift (only to the entire information) On this occasion, the thickening of the osseous layer is carried out by the bore of the cylindrical implant camp. This method assumes a certain thickness of the maxillary sinus ground (min 4 mms), while the direct procedure to is far practicable less than 1 mm of layer thickness. ökoDENT offers at the moment for this no instruments!
��� � ������������������������ ��� � ������������������������� �������� � ��������������� ������ � �����������������
Spezial information
�������
������������ ���������������������������� �������