ISSN 2320 – 6020
IJBSTR RESEARCH PAPER VOL 1 [ISSUE 8] AUGUST 2013
Analysis of Finite Element Mesh Spacing Influence on Modeling Results Rohit Rai ABSTRACT- In the present work the modeling of curved deck slab was done with computer program which was done with the help of finite element method . In model the mesh spacing was varied and its influenced on various properties i.e. deflection, bending moments, and torsional moments are discussed. In this only quadrilateral meshing is taken. And it was found that the mesh spacing changes the results of FE Analysis. However, italso was found out that after certain value of mesh divisions the results start to converge. KEY WORDS: Deflection, Bending Moment, Transverse Moment and Torsional Moment.
OVERVIEW OF FINITE ELEMENT ANALYSIS The finite element is a technique for analyzing complicated structures by notionally cutting up the continuum of the prototype into a number of small elements which are connected at discrete joints called nodes. For each element, approximate stiffness equations are derived relating displacements of the nodes to node forces between elements and in the same way the slope –deflection equation can be solved for joints in a continuous beam, an electronic computer is used to solve the very large number of simultaneous equations that relate node force and displacements. Since the basic principle of subdivision of structure into simple elements can be applied to structures of all forms and complexity, there is no logical limit to the type of structure that can be analyzed if the computer program is written in the appropriate form. Consequently finite elements provide the more versatile method of analysis at present, and for some structures only practical method .However the quantity of computation can be enormous and expensive so that the cost cannot be justified for run of mill structures. Furthermore, the numerous different theoretical formulations of element stiffness characteristics all require approximations in different ways affect the accuracy and applicability of the method .Further research and development is required before the method will have the ease of use and reliability of the simple methods of bridge deck analysis. Author: Rohit Rai is currently pursuing master of technology program in Department of civil engineering Madan Mohan Malaviya Engineering College Gorakhpur Uttar Pradesh 273010, E-mail: rohit.rai2609@gmail.com
The technique was pioneered for two dimensional elastic structures by Turner et al and Clough during the1950s.The whole structure is divided into component elements, such as straight beams, curved beams, triangular or rectangular plate elements, which are joined at the nodes. When this method is applied to a slab, the slab is divided into triangular, rectangular or quadrilateral elements. Thus, the corners of the elements become nodes usually; the vertical deflections of the plate element are expressed in a polynomial of the coordinates of the vertices of the element. This polynomial satisfies the conditions at the corners but may violate the continuity condition along the sides of the element. During recent years, several research workers have attempted to analyze curved bridge decks by the finite element method. Jenkins and Siddall used a stiffness matrix approach and represented the deck slab with finite elements in the form of annular segments, while Cheung adopted the triangular elements. In addition, a horizontal curved box-beam highway bridge was investigated in a three dimensional sense by Aneja and Roll. MODELING OF SLABS USING FINITE ELEMENTS If the finite element method is to be a useful tool in the design of reinforced concrete flat plate structures, accurate modeling is a prerequisite. Accurate modeling involves understanding the important relationships between the physical world and the analytical simulation. As Clough states, “Depending on the validity of the assumptions made in reducing the physical problem to a numerical algorithm, the computer output may provide a detailed picture of the true physical behavior or it may not even remotely resemble it”. The following sections attempt to expose the gap between physical and analytical behavior.
69
© ijbstr.org
ISSN 2320 – 6020
IJBSTR RESEARCH PAPER VOL 1 [ISSUE 8] AUGUST 2013 ANALYSIS FOR MESH SPACING
Table 2: Result obtained for mesh division 05
For the mesh analysis we selected a model of curved deck slab which has a radius of 1.27m ,outer arc length 2m and width if .90m . For the analysis we have taken a UDL loading which is kept constant for all the cases and there results are discussed and the results of longitudinal moments and torsional moments are compared with the moment obtained by analytical method. And the finite element program we selected STAAD Pro. In STAAD Pro we have two type of meshing polygonal and quadrilateral meshing .For our present study we had taken only the quadrilateral meshing in this the mesh is created by selecting the node and after selection we need to give the number of small divisions which we want to give that also would be in quadrilateral shape.
Case 3:Mesh Division=10
Case 1: Mesh Division = 01
Fig. 1: Mesh Diagram with Division 01 Fig 3: Mesh Diagram with division 10 Table 3: Result obtained for mesh division 10
Table 1: Result obtained for mesh division 01
Case 4: Mesh Division = 15 Case 2: Mesh Division = 05
Fig 4: Mesh Diagram with division 15
Fig 2: Mesh Diagram with division 05
70
Š ijbstr.org
ISSN 2320 – 6020
IJBSTR RESEARCH PAPER VOL 1 [ISSUE 8] AUGUST 2013
converge to the correct numerical solution such that a significant increase in the number of elements produces an insignificant change in a particular response quantity. Not all response quantities will converge at the same rate, however. Displacements will generally be the most accurate response quantity computed and will converge faster than stresses, with the exception of some elements derived with hybrid stress formulations, in which case the stresses can converge at the same rate or higher than the displacements.
Table 4: Result obtained for mesh division 15
Case 5: Mesh Division = 20
Fig 6: Displacement Vs. Divisions
Fig 5: Mesh Diagram with division 20 Table 5: Result obtained for mesh division 20
DISCUSSION ON RESULT’S The finite element method is an approximate technique, and as such, results computed using the finite element method must be critically evaluated before relied upon in a design application. This process of critical evaluation involves several steps for any structure being analyzed. The number of elements used in a model can greatly affect the accuracy of the solution. In general, as the number of elements, or the fineness of the mesh, is increased, the accuracy of the model increases as well. As multiple models are created with an increasingly finer mesh, the results should
Fig 7: Absolute stress Vs. Divisions Above fig shows that the variation of absolute stress with respect to division shows that the results to converge at about divisions is about 10.
71
© ijbstr.org
ISSN 2320 – 6020
IJBSTR RESEARCH PAPER VOL 1 [ISSUE 8] AUGUST 2013
Fig 8: Longitudinal Moment Vs. Divisions
Fig 10: Torsional Moment vs. Divisions
From above fig (8) the longitudinal moment with respect to divisions it starts to converge at division about 20.The result of longitudinal was to much agreement when the number of divisions were 20.
For torsional moment the convergence is achieved only at about 10 division and further increase in division only refines the value .The comparisons with the Results obtained by FE Analysis at about 20 divisions is much close to that obtained by analytical methods. CONCLUSION 1. The modeling should be done in a very proper way. 2. More the fineness of the meshing more are the chances of getting accurate results. 3. But if we continue to increase the fineness of mesh that will make our program more bulky and which will slow the processing speed. 4. The storage requirement also increases with meshing. REFERENCE 1.
2.
3. Fig 9: Transverse moment Vs. Division As far the case of transverse moment goes the value of moment starts to converge at about 10 divisions.
4.
.Turner,M.J.,Clough,R.W.,Martin,H.C.and Topp, L. J (1956) Stiffness and deflection analysis of complex structures, J. Aero. Sci.23, 805-23. Clough,R.W.(1960) „The finite element in plane stress analysis‟,Proc.2nd A.S.C.E conf. on Electronic Computation, Pittsburg, Pa., Sept. Burnett, D. S. (1987) Finite Element Analysis, Addison-wesley, Reading, Mass. Bentley Systems (2010), „STAAD Pro. Lab manual: Getting Started and Tutorials.
72
© ijbstr.org