G E N E R A L C ATA LO G U E 7 1
ARCHITECTURAL FLOORING PRODUCTS SLIP RESISTANT SAFETY STAIR TREAD NOSINGS DIRT CONTROL ROLL UP ENTRY MATS PAVING MOVEMENT CONTROL SYSTEM FLEXIBLE MECHANICAL EXPANSION JOINT COVERS LATHAMGRATE ARCHITECTURAL GRATES & FRAMES TACTILE INDICATOR STUDS HANDRAILS & WALL PROTECTION SYSTEMS
MORE THAN 60 YEARS EXPERIENCE IN THE DESIGN AND MANUFACTURE OF ARCHITECTURAL FLOORING PRODUCTS
LATHAM ASBRA SLIP RESISTANT STAIR TREAD NOSINGS
O V E R 5 0 Y E A R S O F E X P E R I E N C E I N T H E D E S I G N & D E V E LO P M E N T O F A B R A S I V E S L I P R E S I S TA N T P R O D U C T S
Economical and easy to install, Latham Safety Stair Treads and Nosings provide slip resistant protection for pedestrians, building occupants and owners. The stair tread nosings highlight the leading edge of the stair and are filled with slip resistant black Suregrip or coloured Supagrit silicon carbide granules.
Finishes Asbraloy™ Aluminium Asbraloy Aluminium profiles are supplied in mill finish. On request profiles can be supplied with a polished bullnose or in clear anodized finish at additional cost. In marine type applications Asbraloy profiles should be specified with 20 micron clear anodised finish.
Finishes Asbrabronz™ Solid Brass Asbrabronz Brass profiles are supplied in brush finish. On request profiles can be supplied with a polished bullnose. Screw Hole Fixings Unless otherwise specified at time of order, holes will be provided in the treads to suit 8 gauge stainless steel or brass screws at Latham’s standard 250mm centres.
Curved Nosings Some profiles can be curved to a constant radius. Discuss with your Latham representative the radius required and if convex or concave along front edge of nosing before specifying and purchase. Hard template suitably marked up showing front leading edge of step and template marked visual top face must be provided.
See details under Accessories-Fixing page 04 of Latham Asbra Safety Stair & Flooring Catalogue 14. Any special machining, mitering, modifications or alternative hole locations will be carried out at extra cost.
Lengths All Asbraloy and Asbrabronz profiles are offered factory cut to the site required length (up to 4600mm in one (1) continuous length) complete with countersunk holes, stainless steel or brass screws (depending on the selected section) and plastic plugs. If specified at time of order, treads can be supplied in full manufacturing lengths of 4600mm for on site cutting and drilling to suit clients sourced fixings. All Asbraloy and Asbrabronz Safety Stair Tread Nosings are discreetly stamped on the surface close to one end as manufactured by “Latham Australia Sydney”, which ensures installed material can be identified in the future and is the clients confirmation that the specified product has been installed. Factory Cutting Tolerance: +0/-3mm.
Slip Resistant Testing Slip Resistant Test results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on page 76 to 78 of Latham Asbra Safety Stair & Flooring Catalogue 14.
Fire Testing Fire Test Results for Asbraloy and Asbrabronz profiles in accordance with AS ISO 9239.1 2003 can be found on page 83 of Latham Asbra Safety Stair & Flooring Catalogue 14. Luminance Contrast Testing Luminance Contrast Testing information as detailed in AS 1428.1-2009 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on pages 79 to 82 of Latham Asbra Safety Stair & Flooring Catalogue 14.
2 | Designs and specifications subject to change without notice
Extra Chemical Resistance Extra Chemical Resistance Infill should be specified for areas where harsh or corrosive chemicals are used, such as commercial cleaning compounds in commercial kitchens. Lathams recommend Gold-Chem Neutral Ph Concentrated Cleaner for all Asbraloy and Asbrabronz products.
14
2 8.1- 2
Stair Tread Nosing Installation Instructions Instructions on how to install stair tread nosings can be found on pages 58 to 61 of Latham Asbra Safety Stair & Flooring Catalogue 14.
T
9
CO
MP
Architectural Specifications and Compliance Architectural specifications and slip resistant test compliance results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on pages 71 to 78 of Latham Asbra Safety Stair & Flooring Catalogue 14.
00
AS
SLIP RESISTANT STAIR TREAD NOSINGS LIA
N
AS 1428.1:2009 Compliant The profiles marked this way meet the width and depth requirements set out in this standard. It should be noted however that when an aluminium or brass nosing with a deeper bullnose is required, a number of certifiers have claimed that the vertical face strip of the nosing is a different colour to the horizontal surface and assuming the contrast is suitable, they have deemed these will comply with the standard. This would need to be clarified with the relevant parties.
STAIR TREAD NOSING INFILL TYPES & COLOUR RANGE Comprehensive information on luminance reflective values for Latham Tread Insert as tested by a NATA Accredited Test Facility in accordance with AS 1428-1.2009 can be found on pages 79-82 of Latham Asbra Safety Stair & Flooring Catalogue 14 or on our website http://www.latham-australia.com/asbra-safety-stair-treads-luminance-testing-information. The information below is dry luminance reflective values for the Latham full abrasive range of stair tread nosings and inserts. SPARKLING BLACK LRV 4.45
BROWN LRV 6.19
OFF WHITE LRV 35.67
TERRACOTTA LRV 8.33
CACTUS GREEN LRV 11.58
SILVER GREY LRV 18.17
BUFF LRV 21.15
TEAL LRV 15.49
BLUE GREY LRV 16.71
TEAK LRV 12.31
BLUE LRV 7.51
SAFETY YELLOW LRV 22.69
LUMO LUMINESCENT GLOW-IN-THE-DARK LRV 38.75
Let Latham Australia test it for you! Using the laboratory method detailed in the Australian Standard. Latham Australia Pty Ltd, would be pleased to measure the dry (and wet if required) luminance reflectance value (LRV) for your floor finish, in our laboratory at our Gladesville (NSW) facility. We will then supply a report which indicates which of the Latham’s colour range will achieve greater than the 30% luminance contrast with the proposed floor finish. Latham Australia Pty Ltd use a specialised Spectrophotometer which is serviced and calibrated by a NATA accredited facility. If you would like to use this service contact Latham Australia Pty Ltd and request further information on LRV testing by Latham Australia. Email: techreq@latham-australia.com.
www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 3
ASBRALOY™ ALUMINIUM & ASBRABRONZ™ SOLID BRASS AB-AW ASBRALOY ALUMINIUM SUPER VISUAL RANGE OF TREADS
I N T E R I O R & E X T E R I O R A P P L I C AT I O N
The Latham AW-AB Asbraloy Super Visual Range of Treads are specifically designed to meet the needs of compliance standards: AS 1428.1:2001, AS/NZS 1428.4.1:2009, AS 4586:2013, AS 4663-2013 in terms of visual requirements, whilst maintaining the slip resistant architectural finish that is synonymous with the range of Latham Asbraloy and Asbrabronz Safety Stair Tread Nosings. The products are supplied in specially formulated 20 micron anodised black finish and off white powder coated finish to match the Latham Supagrit Silicon Carbide Mineral Inserts, offering the best pedestrian safety available in a stair tread nosing. The Latham All Black AB-Series is specifically designed to be installed in conjunction with light coloured floor surroundings to emphasize the tread edge. The Latham All White AW-Series is specifically designed to be installed in conjunction with dark colour flooring. These treads are specifically designed to achieve the luminance contrast required on the riser and tread, when used in the correct colour configurations. 50
50 5
5
ASBRALOY AB-493S (ALL BLACK)
ASBRALOY AW-493S (ALL WHITE) 75
75 10
5 58 15 ASBRALOY AB-734ST (ALL BLACK)
10
5 58 15 ASBRALOY AW-734ST (ALL WHITE)
75 10
75 5
73 ASBRALOY AB-775S (ALL BLACK)
10
60
14
2 8.1- 2 00 9
CO
MP
5
LI
AN
10
57 ASBRALOY AB-FA601S (ALL BLACK 50mm ABRASIVE STRIP)
5 57 ASBRALOY AW-FA601S (ALL WHITE 50mm ABRASIVE STRIP)
75
T
AS
60 10
5 73 ASBRALOY AW-775S (ALL WHITE)
10
75 5
15 ASBRALOY AB-FA751ST (ALL BLACK 50mm ABRASIVE STRIP) 57
10
59
59 5
10
5 15 ASBRALOY AW-FA751ST (ALL WHITE 50mm ABRASIVE STRIP) 57
10
56 ASBRALOY AB-FA501S (ALL BLACK 50mm ABRASIVE STRIP)
5 56 ASBRALOY AW-FA501S (ALL WHITE 50mm ABRASIVE STRIP)
75 10
75 5
58
15 ASBRALOY AB-FA711ST (ALL BLACK 50mm ABRASIVE STRIP)
10
5 58
15 ASBRALOY AW-FA711ST (ALL WHITE 50mm ABRASIVE STRIP)
More detailed information can be found on our website and in Asbra Safety Stair & Flooring Products Catalogue 14 Architectural Specifications and Compliance Screw Hole Fixings Profiles
Architectural specifications and slip resistant test compliance results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on page 71 to 78 of Asbra Safety Stair and Flooring Products Catalogue 14. - Denotes factory drilling location. Illustrations are 75% size in mm. For installation instructions see pages 58 to 61 of Asbra Safety Stair and Flooring Products Catalogue 14.
4 | Designs and specifications subject to change without notice
SLIP RESISTANT STAIR TREAD NOSINGS AS 1428.1-2009 COMPLIANT AT A GLANCE
I N T E R I O R & E X T E R I O R A P P L I C AT I O N
Although there are many varied and sometimes contradictory standards in Australia and through-out the world, Latham strive where possible to meet these and are constantly updating our range to address the sometimes unforeseen and unexplained changes to various Standards. In relation to Standard AS 1428.1-2009, all these profiles on pages 4 and 5 meet the width and depth requirements set out in this standard. Although final confirmation should be through a certifier. From the Asbraloy Aluminium Range
From the Asbrabronz Brass Range 50
59
50 5
5
10
56 ASBRALOY FA501S (BLUE 50mm ABRASIVE STRIP)
ASBRALOY 493S (BLUE GREY)
ASBRABRONZ B493S (TERRACOTTA) 59
50
60 5
10
5
10
10
57
ASBRALOY ACS-50 (SPARKLING BLACK -STANDARD INFILL)
ASBRALOY FA601S (ALL WHITE 50mm ABRASIVE STRIP)
75
10
58
15 ASBRALOY FA711ST (TEAK 50mm ABRASIVE STRIP)
AS
10
9
15
1
4 2 8.1- 2
00
5 58
CO
MP
75 5
LIA
N
10
15 ASBRALOY FA751ST (BROWN 50mm ABRASIVE STRIP) 57
5 58
15 ASBRABRONZ BFA711ST (SILVER GREY 50mm ABRASIVE STRIP)
5 58 15 ASBRABRONZ B734ST (TERRACOTTA) 75
5
10
73 ASBRALOY 775S (TEAL) 75
10
56 ASBRABRONZ BFA501SB (BUFF 50mm ABRASIVE STRIP)
75
75 10
5
T
ASBRALOY 734ST (CACTUS GREEN)
10
3
75
75 10
56 ASBRABRONZ BFA501S (TEAL 50mm ABRASIVE STRIP) 59
5
10
5
3
5 73 ASBRABRONZ B775S (BROWN-STANDARD INFILL) 75
5
73 ASBRALOY 775SB (BLUE GREY)
10
3
5
73 ASBRABRONZ B775SB (CACTUS GREEN)
More detailed information can be found on our website and in Asbra Safety Stair & Flooring Products Catalogue 14 Architectural Specifications and Compliance Screw Hole Fixings Profiles
Architectural specifications and slip resistant test compliance results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on page 71 to 78 of Asbra Safety Stair and Flooring Products Catalogue 14. - Denotes factory drilling location. Illustrations are 75% size in mm. For installation instructions see pages 58 to 61 of Asbra Safety Stair and Flooring Products Catalogue 14. www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 5
ASBRABRONZ™ SOLID BRASS ASBRABRONZ SOLID BRASS STAIR TREAD NOSINGS I N T E R I O R & E X T E R I O R A P P L I C AT I O N
20
48 43 ASBRABRONZ B503S (SPARKLING BLACK)
80
AS AS
T
LIA
2 8.1- 2
MP
LIA
More detailed information can be found on our website and in Asbra Safety Stair & Flooring Products Catalogue 14 Architectural Specifications and Compliance Screw Hole Fixings Profiles
Architectural specifications and slip resistant test compliance results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on page 71 to 78 of Asbra Safety Stair and Flooring Products Catalogue 14. - Denotes factory drilling location. Illustrations are 75% size in mm. For installation instructions see pages 58 to 61 of Asbra Safety Stair and Flooring Products Catalogue 14.
6 | Designs and specifications subject to change without notice
N
9
15 ASBRABRONZ BFA711ST (SILVER GREY 50mm ABRASIVE STRIP)
2 8.1- 2
00
ASBRABRONZ B745S (BROWN-STANDARD INFILL)
58
14
CO
37
10
5
N
9
75 5
14
MP
73 ASBRABRONZ B775SB (CACTUS GREEN)
75
73
5
CO
10
73 ASBRABRONZ B745SB (BLUE GREY)
3
LIA
00
5
9
75
3
N
2 8.1- 2
MP
73 ASBRABRONZ B775S (BROWN-STANDARD INFILL)
LIA
00
75
14
CO
10
75 ASBRABRONZ B755SB (TEAK)
5
AS
75
3 5
37
9
80
37
MP
ASBRABRONZ B805S (BLUE)
N
2 8.1- 2
CO
5
14
LIA
00
5
AS
75
75 ASBRABRONZ B755S (BUFF)
37
MP
ASBRABRONZ B493S (TERRACOTTA)
T
69 ASBRABRONZ B765S (SILVER GREY)
2 8.1- 2
CO
12
ASBRABRONZ B322S (TEAL)
14
9
5
AS
50 5
00
5
ASBRABRONZ BCS-20 (BROWN -STANDARD INFILL)
T
75
33
10
T
12.5
6
T
Asbrabronz Solid Brass Safety Stair Tread Nosings are filled with slip‑resistant Suregrip or Supagrit silicon carbide mineral granules for heavy and light duty applications and are available with a wide range of insert colours.
N
LED TREDLITE STAIR TREAD NOSINGS L AT H A M
LED TREDLITE DECORATIVE NOSING SYSTEMS
I N T E R I O R & E X T E R I O R* A P P L I C AT I O N
Latham Illuminated Slip Resistant Safety Stair Tread Nosings feature the newest safe low voltage 24V LED lighting technology, which is cheap and efficient to run. For most applications all necessary hardware can be supplied, including transformers which will simply plug into a power point. Economical and easy to install, Latham Illuminated LED Tredlite Decorative Safety Stair Treads provide visual enhancement and
slip resistant protection for pedestrians, building occupants and owners. The stair tread nosings highlight the leading edge of the step and are filled with slip-resistant Suregrip and Supagrit silicon carbide mineral granules for heavy and light duty applications. Service factors must be taken into consideration when selecting stair tread profile. * Latham recommend it only be used in protected external applications.
ASBRALOY FL-734ST (BLUE GREY)
ASBRABRONZ TOP-B745S (BROWN)
ASBRALOY TOPDEC-745S (CACTUS GREEN)
ASBRALOY FL-745S (TERRACOTTA)
ASBRABRONZ TOPDEC-B1005ST (TEAL)
ASBRALOY FL-AB775S (ALL BLACK)
More detailed information can be found on our website and in Asbra Safety Stair & Flooring Products Catalogue 14 Architectural Specifications and Compliance
Architectural specifications and slip resistant test compliance results in accordance with AS 4586-2013 for Latham Suregrip and Supagrit Silicon Carbide Mineral Inserts can be found on page 71 to 78 of Asbra Safety Stair and Flooring Products Catalogue 14.
Profiles
Illustrations are 75% size in mm. For installation instructions see pages 58 to 61 of Asbra Safety Stair and Flooring Products Catalogue 14. www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 7
L AT H A M
DIRT CONTROL ROLL UP ENTRY MATS & MAT FRAMES
S U R FA C E M O U N T E D & R E C E S S M O U N T E D R O L L U P M AT S COMMERCIAL & INDUSTRIAL USE
Latham have been designing and manufacturing entry mats to the highest level, for over 30 years. The Latham range of Entry Mats have been specifically designed to facilitate dirt and water control. Research indicates that over 70% of dirt, dust and moisture, in regular occurrences and uses, enters a building via foot and wheeled traffic. These contaminants cause damage and wear on floor finishes, they increase cleaning and maintenance costs, reduce the life cycle of the entrance flooring and can also cause pedestrian safety issues like slips or falls. For these reasons, it is imperative that a suitable dirt control flooring system be considered for commercial and high traffic entrances. The Latham Entry Mat systems consist of extruded aluminium tread rails which carry factory installed infills of either abrasive for slip resistance, carpet for dirt control or vinyl for limited slip resistance and dirt control. The systems are continuously hinged with neoprene joints which reduce traffic noise and rattle. The easy to install, versatile roll up mat, either recessed or surface mounted, has many commercial and industrial applications. In entry ways or in service areas of apartments, offices, hotels, motels, retail shops, malls, restaurants, bars, schools, churches, factories. The unique neoprene hinge design allows easy roll up and eliminates metal to metal contact and corrosion lock up. Factory perforated 12mm x 4mm elongated slots in the neoprene hinge ensures dirt, moisture and debris is directed under
the mat for future collection. Systems that are slot free, may remove moisture and dirt from shoes, but without the slots to control the dirt, these contaminants are tracked across the mat onto the floor. Mats can be vacuumed over or easily rolled back to remove collected soil and moisture from beneath. Construction A series of aluminium tread rails are spaced at 50mm centres and connected by a continuous neoprene hinge with uniform perforations to allow the effective control of water and small debris. Treads should run counter to walking direction, with tread surfaces to be either carpet, abrasive or vinyl. Available in recessed style for installation into surround frame, or surface mounted. Finish Aluminium tread rails and frames are fabricated from 6063-T6 alloy. Tread rails will be supplied in clear anodised standard finish or optional gold anodised or bronze anodised on request. Standard AAF aluminium frames will be supplied in clear anodised finish whilst all other frames will be supplied in mill finish anodised. Other custom or non-stocked metal colours may be available by request at additional delay and charge.
GENERAL INFORMATION STANDARD DIMENSIONS 5mm gap
50mm centres
8mm
28mm 10mm
40mm Surface Mounted Rubber End 40mm
32mm Available infill
Carpet
Abrasive
Recess Mounted Rubber End 25mm factory cut to suit recess requirement
Vinyl
AVAILABLE CONFIGURATIONS MAT WIDTH: “A” FLOOR MAT LENGTH: “B” “A” Floor Mat Width “B” FloorFLOOR Mat Length A
A
B
B
Standard Recess Mounted Standard Recess Mounted
A
B
Standard Standard Surface Mounted withMounted 4 bevelled edges Surface with 4 bevelled edges
Standard Surface with 2 bevelled edges SpecialMounted Surface Mounted forwith applications whereedges side entry not possible 2 bevelled for is applications where side entry is not possible
For more detailed information and specifications on dirt control entry mats review Latham Flooring Systems 6
Gold Chem Mat Wash 22XX
Vacuum for dirt control. This can be as simple as vacuuming over the mat. From time to time Latham’s suggest rolling up the entry mats and cleaning out the well, which will have trapped dirt, moisture and debris, that has been collected by the mat. All Latham entry mats should be washed from time to time using Latham Gold Chem Mat Wash 22XX. This is designed specifically for use with the mats, will not harm the inserts or aluminium extrusions, and will invigorate the inserts and mat finishes.
Special Note
Mats must be rolled up before moving. They must not be dragged.
Maintenance
8 | Designs and specifications subject to change without notice
DIRT CONTROL ROLL UP ENTRY MATS METAL FINISHES ALUMINIUM TREAD RAILS Standard finish is clear anodised. Bright gold and bronze are available as optional stock colours. Clear anodised finish will be supplied unless otherwise specified.
clear anodised (standard)
bright gold anodised
bronze anodised
TREAD RAIL INFILLS & COLOURS SUPAGRIT ABRASIVE INFILL – SLIP RESISTANCE – RSA/SSA COLOUR RANGE Supagrit™ for slip resistance. Tread rail infill shall have continuous Latham Supagrit Slip Resistant Abrasive Surface. Colours to be selected from Latham Australia’s standard colour range. Standard Supagrit abrasive insert colour is silver grey. Standard insert colour will be supplied unless otherwise specified. SILVER GREY
BLACK
BROWN
TERRACOTTA
TEAK
BUFF
CACTUS GREEN
TEAL
BLUE
BLUE GREY
SAFETY YELLOW
OFF WHITE
*LUMO
*Lumo Luminescent glow-in-the-dark infill. The Lumo Luminescent pale green infill temporarily glows in the dark after exposure to artificial or natural light.
CARPET INFILL – DIRT CONTROL – RDCC/SDCC COLOUR RANGE Carpet for dirt control. Tread rail infill shall be 100% nylon fibre face carpet. Carpet unitary fusion bonded to guard against fraying, delamination or moisture penetration. Carpet to be positively locked into extruded aluminium tread rails. Colours to be selected from Latham Australia’s standard colour range. Standard carpet insert colour is grey. Standard insert colour will be supplied unless otherwise specified. GREY
BLACK
BROWN
CHARCOAL
GREEN
ROYAL BLUE
RUST
TEAK
BUFF
GOLD
RED
VINYL INFILL – LIMITED SLIP RESISTANCE AND DIRT CONTROL – RDCV/SDCV COLOUR RANGE Vinyl for limited slip resistance and dirt control. Tread rail infill shall have continuous Latham Ribbed Vinyl Surface. Colours to be selected from Latham Australia’s standard colour range. Note: RDCV and SDCV should not be considered for external applications or application in direct sunlight. Standard vinyl insert colour is grey. Standard insert colour will be supplied unless otherwise specified. GREY
BLACK
BLUE
RUST
www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 9
ENGINEERED & DESIGNED FOR ULTIMATE PERFORMANCE RECESS MOUNTED ENTRY MATS & FRAMES Latham’s range of recess mounted entry mats are designed to sit in a mat well and be flush with the surrounding floor finish. These should be considered over surface mounted mats where possible. The systems are available with 3 infill types and Lathams recommend that entry mats are installed in surround frames. A frame helps protect the edges of the surrounding floor finish from damage that may be caused by wheeled traffic and other pressures that may come in contact with the exposed floor
finish edge. Latham can supply block‑out or cast‑in frames as shown below for our recessed entry mats The integrated neoprene hinging system in the Latham range of Entry Mats not only limits noise and vibration and controls water and dirt, but also acts as a brake on the surface mounted mats ensuring any tracking due to one directional large volumes of traffic is limited.
TYPE RDCC CARPET INFILL Recess mounted: Carpet infill for dirt control. Standard insert colour grey. Standard insert colour will be supplied unless otherwise specified.
RUST CARPET INFILL
TYPE RSA SUPAGRIT INFILL Recess mounted: Supagrit abrasive infill for slip resistance. Standard insert colour silver grey. Standard insert colour will be supplied unless otherwise specified.
SILVER GREY SUPAGRIT INFILL
TYPE RDCV VINYL INFILL Recess mounted: Vinyl infill for limited slip resistance & dirt control. Standard insert colour grey. Standard insert colour will be supplied unless otherwise specified.
BLACK VINYL INFILL
MAT FRAMES Mat frames must be level filled to mat depth with levelling compound or cement mix. Mat must be fully supported on a level surface. For correct installation all mat frames should be delivered with the mats. All standard aluminium mat frames are supplied in clear anodised finish. All other frames will be supplied mill finish.
DEPTHS AVAILABLE 12mm x 12mm x 3mm (standard)
10 | Designs and specifications subject to change without notice
15mm x 15mm x 3mm 20mm x 20mm x 3mm 25mm x 25mm x 3mm 50mm x 50mm x 3mm
DIRT CONTROL ROLL UP ENTRY MATS SURFACE MOUNTED ENTRY MATS Latham’s Range of surface mounted entry mats are supplied standard with ramped/tapered edges on all 4 sides. This means that traffic can approach from any direction without the possibility of tripping over the raised mat. When the mats are being installed between 2 walls they can be supplied with the front and back ramped/tapered strips only.
ensuring any tracking due to one directional large volumes of traffic is limited. The systems are available with 3 infill types as detailed below. For style and colour range details see page 9.
The integrated neoprene hinging system in the Latham range of Entry Mats not only limits noise and vibration and controls water and dirt, but also acts as a brake on the surface mounted mats TYPE SDCC CARPET INFILL - DIRT CONTROL Surface mounted: Carpet infill for dirt control. Standard insert colour grey. Standard insert colour will be supplied unless otherwise specified.
RUST CARPET INFILL RAMPED 4 SIDES STANDARD. 2 SIDES ON REQUEST [SPECIFY]
TYPE SSA SUPAGRIT INFILL - SLIP RESISTANCE Surface mounted: Supagrit abrasive infill for slip resistance. Standard insert colour silver grey. Standard insert colour will be supplied unless otherwise specified.
SILVER GREY SUPAGRIT INFILL RAMPED 4 SIDES STANDARD. 2 SIDES ON REQUEST [SPECIFY]
TYPE SDCV VINYL INFILL - LIMITED SLIP RESISTANCE & DIRT CONTROL Surface mounted: Vinyl infill for limited slip resistance & dirt control. Standard insert colour grey. Standard insert colour will be supplied unless otherwise specified.
BLACK VINYL INFILL RAMPED 4 SIDES STANDARD. 2 SIDES ON REQUEST [SPECIFY]
For more detailed information and specifications on dirt control entry mats review Latham Flooring Systems 6
Gold Chem Mat Wash 22XX
Vacuum for dirt control. This can be as simple as vacuuming over the mat. From time to time Latham’s suggest rolling up the entry mats and cleaning out the well, which will have trapped dirt, moisture and debris, that has been collected by the mat. All Latham entry mats should be washed from time to time using Latham Gold Chem Mat Wash 22XX. This is designed specifically for use with the mats, will not harm the inserts or aluminium extrusions, and will invigorate the inserts and mat finishes.
Special Note
Mats must be rolled up before moving. They must not be dragged.
Maintenance
www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 11
LATHAM ORIGINAL NEOPRENE-X-PANSION LOC® STRIPS & ADHESIVE FIXED TILE STRIPS
S T O C K & C U S T O M LO C S T R I P S, T H R O U G H B E D LO C S T R I P S, R E B O N I T E LO C S T R I P S & T I L E S T R I P S Latham Neoprene-X-Pansion Loc® Strips and Tile Control Strips are a cost effective pavement movement control system that are fast, efficient and easy to install, leaving no mess and providing a vandal resistant, attractive, permanent and maintenance free means of accommodating movement. Each Neoprene-X-Pansion Loc® and Tile Control Strip is manufactured under strict factory controlled conditions using high quality brass, zinc, stainless steel, aluminium or rebonite side plates bonded to a quality air channeled neoprene core. They are designed specially for installation in ornamental and architectural hard paving, to control the opening of floor joints during expansion and cotraction. They absorb paving growth and minimise edge erosion and cracking.
NEOPRENE-X-PANSION LOC STRIP PROFILE GUIDE All products are supplied in 1800mm lengths. Neoprene-X-Pansion Loc Strips are supplied with the following metal side plate thicknesses: standard brass & zinc products, 1mm thick; stainless steel type 304, 0.7mm thick (note: stainless steel products are not recommended for finish to be ground insitu). Optional 3mm thick brass & 3mm zinc side plates are also available, specify with 3/3mm side plates when ordering e.g. Brass: 3MM-LSB overall product depth (AA) x neoprene width 6 or 12mm.
• When ordering specify metal type LSB, LSZ, LSS,
overall product depth (AA), neoprene width 6 or 12mm . Example FFSLS 22 x 6 (50mm O/A) Brass/ Grey.
• Metal type prefixes:
LSB-Brass, LSZ-Zinc, LSS -Stainless Steel.
SOME PROFILES CAN BE CURVED SUBJECT TO TEMPLATE APPROVAL Metal side plates
Neoprene colours
BRASS (LSB)
STANDARD BLACK
ZINC (LSZ)
GREY
STAINLESS STEEL (LSS)
BUFF
LSB 31 x 6 (31mm O/A) Brass/Black
(BB) (AA) Neprene Maximum Paving Overall Width Thickness Product Depth 22mm 8mm 6mm or 12mm
LSZL 40 x 6 (40mm O/A) Zinc/Grey
31mm
15mm
6mm or 12mm
40mm Low Loop
30mm
6mm or 12mm
50mm
35mm
6mm or 12mm
50mm Low Loop
40mm
6mm or 12mm
65mm
50mm
6mm or 12mm
LSZL 40 x 6 (40mm O/A) Zinc/Buff
Trowel Cut Void to Concrete Base
Specify optional galvanised GW50 or stainless steel SSW50 (external application) wire anchors.
Illustrated approximately 70% Full Size: LSZ 50 x 6 zinc/grey 3MM-LSB 65 x 12 (65mm O/A) Brass/Black
LSS 65 x 12 (65mm O/A) Stainless Steel/Grey
12 | Designs and specifications subject to change without notice
Optional trowel cut installation. White line to indicate trowel cut through underbed to concrete base or install over polyethylene tail. See NXP Catalogue 4 for further detail.
PAVING MOVEMENT CONTROL SYSTEMS LATHAM NEOPRENE STRESS RELIEVING CONTROL STRIPS are designed to be used in applications where Latham Neoprene-X-Pansion Loc® or Tile Strips have been overlooked when the floor finish is installed.
LATHAM CURVED OR CIRCULAR LOC® STRIPS AND TILE STRIPS
FFSLZ 50 x 12 (50mm O/A) Zinc/Grey
Latham Neoprene-X-Pansion Loc and Tile Control Strips can be manufactured to tight curves, to compliment almost any architectural design.
FFSLZ 31 x 12 (31mm O/A) Stainless Steel/Buff
FFSLB 31 x 6 (31mm O/A) Brass/Black
For more detailed information and specifications on Neoprene-X-Pansion Loc Strips review Latham PMCS Catalogue 5 Loc Strip Side Plate Thickness: Brass and Zinc–1.0mm, Stainless Steel–0.7mm. Optional 3mm brass and 2.5mm Zinc side plates available. How to Order Loc Strips:
Specify metal type (LSB, LSZ, LSS), overall product depth (AA) and neoprene width 6 or 12mm e.g. FFSLS 22 x 6 Brass/Grey.
Profiles:
Illustrations are approximately 75% size in mm. Strips for special applications contact our Latham Technical Representative.
NEOPRENE-X-PANSION ADHESIVE FIXED TILE STRIP PROFILE GUIDE All products are supplied in 1800mm lengths. Tile Strip side plates standard thickness: 1.5mm brass & aluminium, 0.7mm stainless steel. Optional 3mm brass & aluminium side plates available. Standard Tile Strips are unsuitable for grinding in place. For grinding in place specify Type G.I.P. Strips (special manufacture). Stainless Steel unsuitable for grinding in place.
• When ordering specify metal type (TSA, TSB, TSS),
maximum tile thickness (BB), neoprene width e.g. TSB 10 x 6 Brass/Buff.
• Metal type prefixes:
TSB‑Brass, TSA‑Aluminium, TSS‑Stainless Steel.
SOME PROFILES CAN BE CURVED SUBJECT TO TEMPLATE APPROVAL Metal side plates
Neoprene colours
BRASS (TSB)
STANDARD BLACK
ALUMINIUM (TSA)
GREY
STAINLESS STEEL (TSS)
BUFF
TS A 10 x 6 (12mm O/A) Aluminium/Black
TSS 8 x 6 (10mm O/A) stainless steel/Buff
(AA) Overall Product Depth 10mm
(BB) Maximum Tile Thickness 8mm
12mm
10mm
6mm or 12mm
15mm
13mm
6mm or 12mm
18mm
16mm
6mm or 12mm
20mm
18mm
6mm or 12mm
22mm
20mm
6mm or 12mm
25mm
23mm
6mm or 12mm
Neoprene Width 6mm or 12mm
TSB 13 x 12 (15mm O/A) Brass/Black
“Maximum Tile Thickness” will be reduced by 2mm when 3mm thick sideplates are selected. 3MM-TSA 25 x 6 (29mm O/A) Aluminium/Buff
3MM-TSB 16 x 6 (20mm O/A) Brass/Grey
For more detailed information and specifications on Neoprene-X-Pansion Tile Strips review Latham PMCS Catalogue 5 Side Plate Thickness:
Brass and Aluminium–1.5mm, Stainless Steel–0.7mm. Optional 3mm Brass and Aluminium side plates available. In non extrusion size brass side plate will be folded 1mm. Non extruded size aluminium side plate will fold 1.2mm.
How to Order Tile Strips:
Specify metal type (TSB, TSA, TSS) , maximun tile thickness (BB) and neoprene width 6 or 12mm e.g. TSB 10 x 6 Brass/Buff.
Profiles:
Illustrations are approximately 75% size in mm. Strips for special applications contact our Latham Technical Representative. www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 13
LATHAM ORIGINAL SELF ALIGNING FLEXIBLE MECHANICAL EXPANSION JOINT COVERS
M U LT I D I R E C T I O N A L M A I N T E N A N C E F R E E S Y S T E M S F O R F LO O R, F LO O R-T O-WA L L, WA L L, C E I L I N G, R O O F, C A R PA R K S & R O A D WAY A P P L I C AT I O N S
When you select Latham Flexible Mechanical Expansion Joint Covers, and have a special configuration fabricated, you are taking advantage of a unique solution to the problem of keeping joint covers firmly anchored despite movement between sections of concrete flooring. This ensures a long-lasting, trouble free and stable floor base. The mechanical expansion joint covers are designed to permit multi-directional six-way movement. The cover unit is free to move horizontally, vertically, and horizontally in shear without damaging the surrounding concrete and paving, deforming the cover plate or shearing the screws holding the cover plate in place. The key to our system is a centering bar which consists of two wear resistant spheres fastened at opposite ends of a flat spring steel bar. These act as lubrication free bearings, minimising
wear on the aluminium and brass tracks in which the mechanism constantly moves. The bars are positioned diagonally across the joint opening. The spring steel centering bar holds the cover plate central and the fixing screws tight. Whatever your project, Latham Flexible Mechanical Expansion Joint Covers are available and can be fabricated to almost any width or required joint movement. Optional water gutters or fire barriers are part of the totally trouble free full joint system. All Latham Mechanical Expansion Joint Covers, unless otherwise detailed, are designed for normal pedestrian applications. If the application is heavier, e.g. high traffic areas like railway stations or airports or where heavier loads may transverse the joint cover, see the heavy duty and vehicular ranges. Consult Latham Australia to specify a suitable cover thickness.
CS ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS
• Illustrated CS-25. Available in aluminium & stainless steel. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Stainless Steel Code
Aluminium Code
A
B
C
D
E
F
Movement
Total Available Movement
Overall Depth
Cover Plate Thickness
CS-25
CA-25
25
86
50
18
12
82
+20/-15mm
35mm
33mm
3mm
CS-50
CA-50
50
111
75
18
12
82
+20/-25mm
45mm
33mm
3mm
CS-35
CA-35
35
125
75
25
20
82
+35/-25mm
60mm
33mm
3mm
CS-60
CA-60
60
150 100
25
20
82
+/-35mm
70mm
33mm
3mm
CS-75
CA-75
75
165 115 25 av 125 wwa
20
82
+/-35mm
70mm
33mm
3mm
Smooth Deck
Ribbed Deck
CS-85
CA-85
85
20
82
+/-35mm
70mm
33mm
3mm
CS-100
CA-100
100 190 140
25
20
82
+/-35mm
70mm
33mm
3mm
CS-135
CA-135
135 225 175
25
20
82
+/-35mm
70mm
33mm
5mm
CA-16 Block-Out Anchor factory drilled with 10mm holes at maximum 500mm centres
B C
D
E
33mm
CA-6 Cast-In Concrete Anchor (optional) at 500mm centres
Optional VWS Water Gutter F
A
LS ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS • Illustrated LS-25. Available in aluminium & stainless steel. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Stainless Steel Code
Smooth Deck
Aluminium Code Ribbed Deck
A
B
C
D
E
F
Total Available Movement
Movement
B C
Cover Overall Plate Depth Thickness
LS-25
LA-25
25
56
38
18
12
82
+/-12mm
25mm
33mm
3mm
LS-50
LA-50
50
81
63
18
12
82
+/-12mm
25mm
33mm
3mm
LS-45
LA-45
46
91
66
25
20
82
+/-20mm
40mm
33mm
3mm
LS-75
LA-75
71
111
91
25
20
82
+/-20mm
40mm
33mm
3mm
LS-100
LA-100
96
137 116
25
20
82
+/-20mm
40mm
33mm
3mm
LS-150
LA-150
146 187 166
25
20
82
+/-20mm
40mm
33mm
5mm
CA-16 Block-Out Anchor factory drilled with 10mm holes at maximum 500mm centres
D
42mm
E Wall member factory drilled to accept countersunk head 6.5mm fixings
33mm CA-6 Cast-In concrete anchor (optional) at 500mm centres
Optional VWS Water Gutter A
F
SAS (FASM 50) ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS • Illustrated SAS-50 (FASM 50). Other depths: 25mm, 32mm, 38mm, 64mm, 79mm, 89mm, 104mm, 114mm, 139mm, 164mm. Wider joint widths available on request. • Available in aluminium & stainless steel. All expansion joint fixing by others. Dimensions are millimetres. Stainless Steel Code
Aluminium Code
SAS-25 (FASM 50)
Total Cover Overall Available Plate Depth Movement Thickness
A
B
C
D
E
F
Movement
SAA-25 (FASM 50)
25
87
50
18
13
60
+20/-15mm
35mm
50mm
3mm
SAS-50 (FASM 50)
SAA-50 (FASM 50)
50
113
75
18
13
60
+20/-25mm
45mm
50mm
3mm
SAS-44 (FASM 50)
SAA-44 (FASM 50)
44
163 100
32
26
87
+50/-30mm
80mm
50mm
3mm
SAS-75 (FASM 50)
SAA-75 (FASM 50)
70
189 125
32
26
87
+50/-50mm
100mm
50mm
3mm
SAS-100 (FASM 50) SAA-100 (FASM 50)
95
214 150
32
26
87
+50/-50mm
100mm
50mm
3mm
SAS-150 (FASM 50) SAA-100 (FASM 50) 145 264 200
32
26
87
+50/-50mm
100mm
50mm
5mm
Smooth Deck
Ribbed Deck
14 | Designs and specifications subject to change without notice
D
B C
E
50mm
Optional BFG Water Gutter F
A
Side members factory drilled with 10mm holes at approximately 475mm centres
EXPANSION JOINT COVER SYSTEMS
2 and 4 hour fire rating available. See Technical Manual 43 for further detail.
water gutter
fire rated
seismic
vehicular
Systems with wide cover plates to accommodate seismic movement are available. See Technical Manual 43 for further detail. fire rated
seismic
IMAGE: CA-25 EXPANSION JOINT COVER
vehicular
SLS (FASM 50) ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS B
• Illustrated SLS-50 (FASM 50). Other depths: 25mm, 32mm, 38mm, 64mm, 79mm, 89mm, 104mm, 114mm, 139mm, 164mm • Available in aluminium & stainless steel. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Stainless Steel Code
Aluminium Code
Smooth Deck
Ribbed Deck
A
B
C
D
E
F
Movement
C D 42mm
Total Cover Overall Available Plate Depth Movement Thickness
SLS-25 (FASM 50)
SLA-25 (FASM 50)
25
58
38
18
13
60
+/-12mm
25mm
50mm
3mm
SLS-50 (FASM 50)
SLA-50 (FASM 50)
50
81
63
18
13
60
+/-12mm
25mm
50mm
3mm
SLS-44 (FASM 50)
SLA-44 (FASM 50)
44
99
72
32
26
87
+/-25mm
50mm
50mm
3mm
SLS-75 (FASM 50)
SLA-75 (FASM 50)
70
125
98
32
26
87
+/-25mm
50mm
50mm
3mm
SLS-100 (FASM 50)
SLA-100 (FASM 50)
95
150 123
32
26
87
+/-25mm
50mm
50mm
3mm
SLS-125 (FASM 50)
SLA-125 (FASM 50) 120 175 148
32
26
87
+/-25mm
50mm
50mm
3mm
SLS-150 (FASM 50)
SLA-150 (FASM 50) 145 200 173
32
26
87
+/-25mm
50mm
50mm
5mm
E Wall member factory drilled to accept countersunk head 6.5mm fixings
50mm
Optional VWS Water Gutter F
A
Side members factory drilled with 10mm holes at approximately 475mm centres
CAB BRASS ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS • Illustrated CAB-25. Other depths: 55mm, 70mm. 80mm, 95mm, 105mm, 130mm, 155mm • Available in brass. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres.
B BM-16 Anchor
B
C
D
E
F
Movement
Total Available Movement
25
86
50
18
13
60
+20/-15mm
35mm
25mm
3mm
50
111
75
18
13
60
+20/-25mm
45mm
25mm
3mm
CAB-51
50
160 100
30
25
75
+/-40mm
80mm
25mm
3mm
CAB-75
75
185 125
30
25
75
+40/-50mm
90mm
25mm
3mm
CAB-100
100 210 150
30
25
75
+40/-50mm
90mm
25mm
5mm
CAB-150
150 260 200
30
25
75
+40/-50mm
90mm
25mm
5mm
Solid Brass Code
A
CAB-25 CAB-50
Overall Cover Plate Depth Thickness
D
E
C
25mm
A
BS-6 Cast-In Anchor (optional)
F
All anchors are supplied welded to the side members at approximately 475mm centres. BM-16 anchors are supplied factory drilled with 10mm holes at approximately 475mm centres
LAB BRASS ULTIMATE SERIES FLOOR EXPANSION JOINT COVERS • Illustrated LAB-25. Other depths: 55mm, 70mm. 80mm, 95mm, 105mm, 130mm, 155mm • Available in brass. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Solid Brass Code
A
B
C
D
E
F
Movement
Total Available Movement
Overall Cover Plate Depth Thickness
LAB-25
25
56
38
18
12
60
+/-12mm
24mm
25mm
3mm
LAB-50
50
82
64
18
12
60
+/-12mm
24mm
25mm
3mm
LAB-51
50
105
75
30
25
75
+/-25mm
50mm
25mm
3mm
LAB-75
75
130 100
30
25
75
+/-25mm
50mm
25mm
3mm
LAB-100
100 155 125
30
25
75
+/-25mm
50mm
25mm
5mm
LAB-150
150 205 175
30
25
75
+/-25mm
50mm
25mm
5mm
All anchors are supplied welded to the side members at approximately 475mm centres. BM-16 anchors are supplied factory drilled with 10mm holes at approximately 475mm centres
B C D 35mm E
25mm
BS-6 Cast-In Anchor (optional)
A
Wall member factory drilled to accept countersunk head 6.5mm fixings
F
www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 15
MULTI DIRECTIONAL & MAINTENANCE FREE Latham Flexible Mechanical Expansion Joint Cover Systems will accommodate general thermal expansion, contraction and shrinkage as indicated in the tables. In some cases, depending on the requirements of the structure, standard systems will also allow seismic movement. Where a structure has been designed to accommodate extreme seismic movement the Latham Seismic Range of expansion joint covers should be considered.
HHS HEAVY DUTY PEDESTRIAN SERIES FLOOR EXPANSION JOINT COVERS • Illustrated HHS-25. Available in aluminium & stainless steel. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Stainless Steel Code
Aluminium Code
A
B
C
D
E
F
Movement
Total Cover Overall Available Plate Depth Movement Thickness
HHS-25
HHA-25
25
130
95
18
12
50
+25/-12mm
37mm
25mm
5mm
HHS-50
HHA-50
50
160 125
18
12
50
+/-25mm
50mm
25mm
5mm
HHS-75
HHA-75
75
175 140
18
12
50
+/-25mm
50mm
25mm
5mm
HHS-100
HHA-100
100 210 175
18
12
50
+/-25mm
50mm
25mm
6mm
HHS-150
HHA-150
150 250 215
18
12
50
+/-25mm
50mm
25mm
6mm
HHS-200
HHA-200
200 300 265
18
12
50
+/-25mm
50mm
25mm
7mm
B D
E
C
Side member factory drilled to accept 8mm countersunk head fixings at approximately 350mm centres
25mm Shallow Block Out (Limited Flexibility) F
A
Optional BFG Water Gutter
HD HEAVY DUTY VEHICULAR FLOOR EXPANSION JOINT COVERS • Illustrated HD-50. Available in aluminium. denotes smooth deck. • All expansion joint fixing by others. Dimensions are millimetres. • Wider joint widths available on request. Aluminium Code
A
HD-50
50
HD-75
75
HD-100
B
C
B D
C
E
50mm
Total Available Overall Cover Plate Movement Depth Thickness
D
E
F
Movement
195 128
34
24
113
+/-36mm
72mm
50mm
6mm
220 153
34
24
113
+/-36mm
72mm
50mm
6mm
100 245 178
34
24
113
+/-36mm
72mm
50mm
6mm
Side members factory drilled with 16mm holes at approximately 250mm centres
Pack with high strength epoxy grout F
Optional VWS Water Gutter
Optional BFG Water Gutter
A
ABS SURFACE-LINE SERIES FLOOR EXPANSION JOINT COVER • Illustrated CPA-100. Available in aluminium. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Aluminium Code
A
B
Movement
Total Available Movement
Overall Depth
ABS-10
12
133
+/-12mm
24mm
Surface Mounted 4.5mm
Ribbed Deck
Typical Vinyl Installation
B
Factory drilling available on request
A
4.5mm
CPA HEAVY DUTY VEHICULAR SURFACE MOUNTED FLOOR EXPANSION JOINT COVERS • Illustrated CPA-100. Available in aluminium. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Aluminium Code
A
Ribbed Deck
CPA-100
B
C
22-125 305
D
27
E
22
F
10
25
B F E
Total Available Vertical Incline Movement
Movement 22-130mm
108mm
C
+/-8º
Side member factory drilled to accept 10mm countersunk head fixings at approximately 350mm centres
D
A
HDASM HEAVY DUTY VEHICULAR SURFACE MOUNTED FLOOR EXPANSION JOINT COVERS • Illustrated HDASM-50. Available in aluminium. Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. denotes smooth deck. Aluminium Code
A
HDASM-50
50
HDASM-75
75
HDASM-100
B
C
Total Cover Overall Available Plate Depth Movement Thickness
D
E
F
Movement
318 128
81
14
110
+/-25mm
50mm
46mm
6mm
343 153
81
14
110
+/-25mm
50mm
46mm
6mm
100 368 178
81
14
110
+/-25mm
50mm
46mm
6mm
16 | Designs and specifications subject to change without notice
B E
D
22mm
C
50mm
6mm aluminium deck 6mm
34mm
Side member factory drilled to accept 10mm countersunk head fixings at approximately 350mm centres
23mm
F
Optional BFG Water Gutter A
Titazel Thixotropic Epoxy Adhesive Bedding
EXPANSION JOINT COVER SYSTEMS K WALL-LINE WALL & CEILING SERIES EXPANSION JOINT COVERS • Illustrated 25K. Available in aluminium – clear anodised finish standard. • Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Aluminium Code
A
B
C
Movement +30/-20mm
Total Available Movement 50mm
Overall Depth 16mm
25K
25
101
38
50K
50
126
38
+/-30mm
60mm
16mm
75K
75
191
58
+/-50mm
100mm
16mm 16mm 16mm
100K
100
216
58
+/-50mm
100mm
150K
150
266
58
+/-50mm
100mm
B
Add “D” to increase the overall depth from 16mm to 18mm e.g. 25KD.
C 16mm Base plate drilling by others Optional BFG Water / Wind Barrier
A
L WALL-LINE WALL-TO-WALL SERIES EXPANSION JOINT COVERS • Illustrated 25L. Available in aluminium – clear anodised finish standard. • Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Aluminium Code
A
B
C
Movement
25L
25
83
58
+25/-15mm
Total Available Movement 40mm
Overall Depth 16mm
50L
50
108
58
+/-25mm
50mm
16mm
75L
75
133
58
+/-25mm
50mm
16mm
100L
100
158
58
+/-25mm
50mm
16mm
150L
150
208
58
+/-25mm
50mm
16mm
16mm B
Add “D” to increase the overall depth from 16mm to 18mm e.g. 25KD.
45mm C 16mm Base plate drilling by others A
Optional BFG Water / Wind Barrier
FR ROOF -LINE SERIES ROOF & ROOF-TO-PARAPET EXPANSION JOINT COVERS • Illustrated FR-50 . Available in aluminium. • Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. Aluminium Code
A
B
C
Movement
Total Available Movement
Overall Depth
FR -25
25
114
64
+25/-15mm
40mm
88mm
FR-50
50
165
64
+50/-42mm
92mm
88mm
FR-75
75
190
64
+/-50mm
100mm
88mm
FR-100
100
215
64
+/-50mm
100mm
88mm
FR-150
150
265
64
+/-50mm
100mm
88mm
B Splice cover Side member factory drilled with 10mm holes at approximately 475mm centres
88mm
C
A
LIGHT DUTY SERIES FLOOR & FLOOR-TO-WALL EXPANSION JOINT COVERS • Illustrated 50-FDR (30) & 50 FDRW (30) . Available in aluminium.
50-FDRW (30)
• Wider joint widths available on request. • All expansion joint fixing by others. Dimensions are millimetres. • Interior application only. Aluminium Code
A
B
C
D
E
50-FDR
50
48
42
50
50
50-FDRW
50
45
42
50
50
50-FDR (20)
50
48
42
50
20
50-FDRW (20)
50
45
42
50
20
50-FDR (30)
50
48
42
50
30
50-FDRW (30)
50
45
42
50
30
F
38 38 38
Wall members factory drilled to accept 8 guage screw & plug at approximately 475mm centres on request
50-FDR (30)
Movement
Total Available Movement
Overall Depth
+/-5mm
10mm
50mm
+/-5mm
10mm
88mm
+/-5mm
10mm
20mm
+/-5mm
10mm
58mm
+/-5mm
10mm
30mm
+/-5mm
10mm
68mm
B
F
C E
D
B C
E
A Side members factory drilled with 10mm holes at approximately 475mm centres
A D Side members factory drilled with 10mm holes at approximately 475mm centres
For more detailed information and specifications on Mechanical Expansion Joint Covers review Latham Technical Manual 43 Metal Extrusions
Aluminium 6063-T5 & T6 mill finish alloy, brass 380 mill finish alloy or stainless steel decks, Type 304 Grade 2B finish to 3mm thick
Vinyl Extrusions
All vinyl plastic extrusions used are polyvinyl chloride (thermoplastic)
Profiles
Illustrations are 30% size in mm. Products subject to alterations without notice
Note 1
Movement referred to in this publication should be viewed in the following way. The + (positive) factor refers to the effective amount the joint cover can extend (the joint in the slab increases in width), whilst the – (minus) factor refers to the effective amount the joint cover can contract (the joint in the slab decreases in width). These are effective movements, the systems may be effected by load and traffic volume and other circumstances, which may require a larger or heavier system to be considered. www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 17
LATHAMGRATE ARCHITECTURAL GRATES & FRAMES
Typical Lathamgrate Aluminium & Brass T Spacing 6.25mm
13mm
The systems also offer tremendous flow rates for air and water meaning they are suitable for drainage or ventilation applications.
6.25mm
13mm
32mm
The Lathamgrate™ aluminium and brass trench gratings and frames are an economical, functional and attractive solution to exterior and interior drainage and ventilation issues. The serrated texture, provides a dynamic yet contemporary appearance that compliments today’s and tomorrow’s architectural designs. Unlike conventional grating, the serrated 6.5mm T’s offer increased pedestrian safety and the narrow 6.5mm spacings ensure the best performance with high heeled traffic.
34mm
Most of the Lathamgrate™ range is available for trench widths up 300mm wide as standard. Widths indicated in this catalogue are a guide only and Latham can custom manufacture systems to varying widths. All Latham Aluminium and Brass Grates have undergone Slip Rating Tests in accordance with AS/NZ 4586:2004.
ALGRS SERIES ALUMINIUM SERRATED TOP TRENCH GRATE B
37mm
A
Trench Channel By Others
ALGRS Series serrated top aluminium trench grates are designed for surface mounted pedestrian applications. The ALGRS Series is supplied as a complete drop in unit system. It is self-supporting on the surround frames, making for easy removal for access and cleaning. The material can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available for the surface mounted grate if required. The system is also available with end frame surrounds.
Aluminium Serrated Top
A
B
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) as per AS 3996 Serrated T’s
ALGRS-3S
72mm 120mm
300
A
4
ALGRS-4S
97mm 145mm
420
A
6
ALGRS-5S
122mm 170mm
540
A
8
ALGRS-6S
147mm 195mm
660
A
10
ALGRS-8S
197mm 245mm
900
A
14
ALGRS-10S
249mm 295mm
1140
A
18
ALGRS-12S
297mm 345mm
1320
A
21
BRGRS SERIES SOLID BRASS SERRATED TOP TRENCH GRATE B
38mm
A
18 | Designs and specifications subject to change without notice
Brass Serrated Top
A
B
BRGRS Series serrated top solid brass trench grates are designed for surface mounted pedestrian applications. The BRGNS Series is supplied with the frame that is set on a preformed bearing platform. The grates will simply drop in making for easy removal for access and cleaning. The brass grates can be supplied in custom lengths to 4000mm. Factory manufactured fully welded angles and T’s are available as well as hidden locking mechanisms. The system is also available with end frame surrounds.
Trench Channel By Others
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) Serrated T’s as per AS 3996
BRGRS-3S
72mm 120mm
300
A
4
BRGRS-4S
97mm 145mm
420
A
6
BRGRS-5S
122mm 170mm
540
A
8
BRGRS-6S
147mm 195mm
660
A
10
BRGRS-8S
197mm 245mm
900
A
14
LATHAMGRATE ARCHITECTURAL GRATES
ALGLS SERIES ALUMINIUM SERRATED TOP TRENCH GRATE B
5mm
Specify Depth
60mm Block Out Anchor (Standard)
A
Optional Trench Liner - Specify
ALGLS Series serrated top aluminium trench grates are designed for surface mounted pedestrian applications. The ALGLS Series consists of a frame that can be supplied with or without an integrated galvanised trench liner, making the frame and liner (if supplied) a permanent part of the floor, whilst the individual grating sections will drop into the frame, ensuring easy removal for access and cleaning. The ALGLS Series Grates and Frames can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available for the grates, frames and trench liners.
Cast-In Anchor (optional)
70mm
Aluminium Serrated Top
A
B
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) Serrated T’s as per AS 3996
ALGLS-4S
80mm 110mm
480
B
ALGLS-5S
105mm 135mm
600
B
7 9
ALGLS-6S
130mm 165mm
720
A
11
ALGLS-8S
180mm 215mm
960
A
15
ALGLS-10S
230mm 267mm
1200
A
19
ALGLS-12S
280mm 306mm
1380
A
22
BRGNS SERIES SOLID BRASS SERRATED TOP TRENCH GRATE B
34mm
3mm Brass Frame
A
BRGNS Series serrated top solid brass trench grates are for pedestrian applications. The BRGNS Series is supplied with the frame that is set on a preformed bearing platforms. The grates will simply drop into the frame making for easy removal for access and cleaning. The material can be supplied in custom lengths to 4000mm for the grate inserts whilst the brass angle frame can be supplied in lengths to 3600mm. Factory manufactured fully welded angles and T’s are available as well as hidden locking mechanisms. The system is also available with end frame surrounds.
Trench Channel By Others
Brass Serrated Top
A
B
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) Serrated T’s as per AS 3996
BRGNS-4S
56mm 100mm
480
A
BRGNS-5S
83mm 127mm
600
A
7 9
BRGNS-6S
108mm 152mm
720
A
11
BRGNS-8S
148mm 192mm
900
A
14
BRGRS-8S
190mm 240mm
900
A
14
www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 |  19
LATHAMGRATE ARCHITECTURAL GRATES ALGPL SERIES ALUMINIUM SERRATED TOP TRENCH GRATE B
6mm
60mm
Grate standing on block work or formed concrete
They are designed to sit on a formed step or trench base and have an overall depth of 60mm. Alternatively, they can sit on levelling rods in the slab, but they must be fully supported at the ends to ensure they do not lift when traffic passes over a joint in an extended run. They carry seamless welded cross B supports at approximately 300mm centres.6mm The grates can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available.
ALGPL Series serrated top aluminium trench grates are predominantly suitable for pedestrian applications. The ALGPL Series are removable solid grate units.
Aluminium Serrated Top
B
Optional extend clips to bottom of trench Consult Latham before specifying
Represents formed trench by others
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) as per AS 3996 Serrated T’s
ALGPL-3S
75mm
300
B
4
ALGPL-4S
100mm
420
B
6
ALGPL-5S
125mm
540
B
8
ALGPL-6S
151mm
660
A
10
ALGPL-8S
204mm
900
A
14
ALGLS-10S
242mm
1080
A
17
ALGLS-12S
308mm
1380
A
22
60mm
BRGPL SERIES SOLID BRASS SERRATED TOP TRENCH GRATE Grate standing on block work or formed concrete
B
Represents formed trench by others
6mm
50mm
Optional extend clips to bottom of trench Consult Latham before specifying Grate standing on block work or formed concrete
Represents formed trench by others
They are designed to sit on a formed step or trench base and have an overall depth of 50mm. Alternatively, they can sit on levelling rods in the slab, but they must be fully supported at the ends to ensure they do not lift when traffic passes over a joint. They carry seamless welded cross supports at approximately 300mm centres. The grates can be supplied in custom lengths to 4000mm and factory manufactured fully welded angles and T’s are available.
Brass Serrated Top
B
BRGPL Series serrated top solid brass trench grates are predominantly suitable for pedestrian applications. The BRGPL Series are removable solid grate units.
Optional extend clips to bottom of trench Consult Latham before specifying
Open Flow Area per lineal Class Classification Number 0f 6.5mm metre of grate (cm²) as per AS 3996 Serrated T’s
BRGPL-3S
75mm
300
B
4
BRGPL-4S
100mm
420
B
6
BRGPL-5S
125mm
540
B
8
BRGPL-6S
151mm
660
A
10
BRGPL-8S
204mm
900
A
14
For more detailed information and specifications on Lathamgrate Architectural Grates and Frames review Latham Flooring Systems 6 Custom Lathamgrate Curved Fabrications Special Note
Latham are happy to discuss custom applications that you may have, including wall systems, ventilation applications and curved applications. Contact your Latham representative to discuss any applications. Curving involves the side sections and the centre T’s being rolled to the required curve before the systems are welded together. Depending on the grate series selected, the grates can be rolled to a radius as tight as 900mm. Please contact Latham Australia or your Latham Australia representative to discuss your application further. A number of the Lathamgrate Series can be supplied with frame surround ends and block ends. This is when the external edge frame is carried around the end of the grate.
20 | Designs and specifications subject to change without notice
LATHAMGRID GRID MATS LATHAMGRID ARCHITECTURAL GRID MATS & FRAMES
A LU M I N I U M & B R A S S G R I D M AT S & F R A M E S A R E AT T R A C T I V E & DY N A M I C PRODUCTS FOR ANY ACCESS AREA
The system consists of unique serrated tee sections for slip resistance with hidden welds and joints, creating a virtually seamless, visually pleasing, architectural asset to any entrance. All Lathamgrid grid mats are custom fabricated to each individual application so the options are virtually endless.
The narrow 3.5mm spacings between the T’s are designed not to interfere with traffic movement over the system. It is recommended that all Lathamgrid grid mats be installed with the longitudinal bars left to right across the doorway as shown in the diagram below.
General Information Aluminium and brass grid mats need to be supported on a hard flat surface, and a surround frame can be supplied in a similar metal for recessed or cast in installation.
The small gap between each T, whilst being visually attractive, allows dirt, dust, and water to be trapped in the base of the grid, reducing the tracking of material and water onto the floor surface. The grids can then be vacuumed to easily remove any debris.
The aluminium and brass serrated T bars are 9.5mm wide as standard, and are installed at approximately 13mm centres.
AVAILABLE IN ALUMINIUM TYPE ALGRID AND BRASS TYPE BRAGRID Depth from top grating to bottom of grating Aluminium 33mm Brass 33mm
GRID MAT LENGTH (B) 3mm
9.5mm
GRID MAT WIDTH (A)
13mm centre to centre
33mm
3mm AAF or BAF Angle Frame (Standard)
45mm Brass or aluminium tread bar ACKD Block-Out or Cast-In Frame
13mm
Floor finish
12mm
48mm
9.5mm
Level recess with a suitable product. Grid mats must be fully supported
Continuous spacer support bar at approx 255mm O.C.
Special Lathamgrid bar spacing
TYPE ALGRID
TYPE BRAGRID
A
How to Order
B
When ordering a grid mat clearly specify walking direction, metal type and overall dimensions “A� mat width and “B� mat length. Length must work in multiples of approximately 13mm. Also available with 6.5mm tee sections. Available to 4600mm in one continuous section.
GRID MAT WIDTH: “A� GRID MAT LENGTH: “B�
For more detailed information on Lathamgrid Architectural Grid Mats and Frames review Latham Flooring Systems Catalogue 6 Slip Resistant Testing
All Latham Aluminium and Brass Grids and Grates have been independently tested by a NATA approved laboratory in accordance with AS 4586:2013 Slip Resistance Classifications of New Pedestrian Surface Materials. Under this testing criteria from the information contained in Appendix A and B all Latham Grids and Grates achieve a wet dry classification of P5 . www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 |  21
TACTILE INDICATOR STUDS LATHAM TI SERIES TACTILE INDICATOR STUDS
I N T E R I O R & E X T E R I O R A P P L I C AT I O N
Latham TI Series Tactile Indicator Studs are available in stainless steel and brass, either with Latham Supagrit silicon carbide slip resistant mineral inserts or full metal (stainless steel only) Spiral Top. The Latham Tactile Indicator Studs have been designed in accordance with AS/NZS 1428.4.1:2009 & AS 1428.1-2009. The Latham Tactile Indicator Studs are designed for applications where rubber and concrete based tactile tiles may not be suitable. The Latham Studs offer a more visually attractive alternative to rubber, porcelain or concrete based products. Applications include hotels, office buildings, museums, shopping centres etc. The Latham Studs can be installed in tiles, marble, granite, terrazzo, concrete, vinyl, timber and most solid flooring surfaces. Whilst the LTSSL Long Stem Tactile Indicator Studs are specifically designed for installation through softer floor finishes like direct stick carpet, into the hard substrate. Contact Latham Australia to discuss your exact application. All studs should be installed into correctly drilled holes using Latham Thixotropic Stud Adhesive. All studs need to be installed in accordance with AS/NZS 1428.4.1:2009 & AS 1428.1-2009, where applicable.
45° angle approx.
3mm deep abrasive inlay 4.5mm 10mm
6mm diameter
10mm
10mm
35mm Diameter
10mm 25mm
LTAS Tactile Indicator Stud
LTSS (10mm) & LTSSL (25mm) Tactile Indicator Studs
Latham Slip Resistant Abrasive Stainless Steel Tactile Indicator Stud, with Supagrit™ terracotta silicon carbide mineral infill.
LTAB Tactile Indicator Stud Latham Slip Resistant Abrasive Brass Tactile Indicator Stud, with Supagrit™ brown silicon carbide mineral infill.
Latham Spiral Top Stainless Steel Tactile Indicator Studs.
SLIP RESISTANT INFILL COLOUR RANGE SILVER GREY
BLACK
BROWN
TERRACOTTA
CACTUS GREEN
TEAL
BLUE
BLUE GREY
TEAK
BUFF
SAFETY YELLOW
22 | Designs and specifications subject to change without notice
OFF WHITE
*LUMO
*Lumo Luminescent glow-in-the-dark infill. The Lumo Luminescent pale green infill temporarily glows in the dark after exposure to artificial or natural light.
Slip Resistance Performance Testing for Asbraloy & Asbrabronz profiles can found on pages 76 to 79 of Latham Asbra Stair & Flooring Catalogue 14. For detailed specifications on Latham Tactile Indicator Studs contact Latham Australia.
LATHAM WALL PROTECTION SYSTEMS WALL PROTECTION SYSTEMS
L E T L AT H A M H A N D R A I L S, B U M P R A I L S, C O R N E R G U A R D S & WA L L P R O T E C T I O N S H E E T I N G M A K E A N I M PA C T, W H I L E TA K I N G O N E, O N Y O U R N E X T P R O J E C T
Latham Hand Rails, Hand/Bump Rails, Illuminated Hand/Bump Rails, Bump Rails, Corner Guards, and Wall Protection Sheeting are designed to provide a simple aesthetically appealing, functional solution for locations where traffic movement may be expected to cause scuffing and damage to walls and corners.
HAND/BUMP RAILS TYPE HR-140
The Latham HBR-160 Series Hand/ Bump Rail is new to the Latham range. The system offers a dual solution in the safety and protection for building occupants and the building itself. Our array of styles and colours offer design potential for any project. The Latham HBR Series is compliant with the latest Australian Standard AS 1428-2009 when installed at the height set out in the Standard.
BUMP RAILS TYPE BR-150 Latham bump rails add a versatile design component to any new or existing project. Latham bump rails are designed for high traffic areas where wall damage will be caused by rolling equipment. They are mounted at primary levels of impact to provide the greatest degree of protection. Selecting from our range of styles and colours, aesthetics won’t be compromised.
50mm
90mm
Extruded Impact Absorbing Strip
Extruded Impact Absorbing Strip
50mm
10mm 50mm
28mm
28mm 90mm
139mm
50mm Adjustable Wall Support
High Impact Textured Cover Profile
Aluminium Base Retainer Profile
12mm
Aluminium Base Retainer Profile
50mm Adjustable Wall Support
High Impact Textured Cover Profile
40mm
Aluminium Base Retainer Profile
160mm
50mm
40mm
Using Latham’s flush-mounted or surface-mounted corner guards will provide built-in protection in new construction or in existing locations. Latham’s corner guards become a creative design element while providing excellent wall protection in environments such as schools, airports or shopping centres.
Approximately 285º
High Impact Textured Cover Profile
Extruded Impact Absorbing Strip
CORNER GUARD TYPE CG-50
150mm
Latham hand rails provide a safe and secure grip. Our array of styles and colours offer design potential for any project. Latham handrails are made of sturdy aluminium frames with vinyl covers that are designed to withstand impact and resist breakage. A fully concealed fastening system will ensure that you get the look you want.
HAND/BUMP RAILS TYPE HBR-160
Usage examples include hospitals, schools, restaurants, offices, nursing homes, shops, passenger check in areas, hotels etc. The textured finish that is on all the sections (excluding the BR-25) provides a hard wearing, scuff & scratch resistant replaceable finish to compliment modern designs.
Base Impact Retainer
10mm
High Impact Textured Cover Profile 28mm
40mm
ADHESIVE FIXED CORNER GUARDS ve si
he
Ad
PCG-25, PCG-50 & PCGF-60
Can accomodate varying angles from flat to more than 135°
m
m
d ce
50
-fa le
or
ub e
p ta
25
50
25
m
m
or
do d el (fi
m
Flexible centre section
m m
m
60
60
d) ie
pl ap
Latham Adhesive Fixed Corner Guards are the perfect solution for damaged corners in hotels, schools, offices, nursing homes, hospitals, restaurants and all commercial buildings. With a tough, rigid textures vinyl surface, they provide an easy way to eliminate corner repair costs and problems in light abuse areas. Installation is convenient with permanent self-adhesive tape.
PVC COLOUR GUIDE Latham Australia offers 6 stock colours. Printed colours may vary slightly from actual PVC material colours. Not all colours stocked im all profiles. HAZY GREY
ALMOND BEIGE
VIOLET
SAPHIRE BLUE
PINE GREEN
BLUE GREY
SNOW WHITE
More detailed information can be found on our website and in Latham Wall Protectiom Systems Catalogue 9 www.latham-australia.com | sales@latham-australia.com | +612 9879 7888 | 23
“Quality products engineered and crafted to meet tomorrow’s needs today…” Over 60 years in the business is proof that we stand behind these words. We customise our products to fit your projects needs. At Latham, we’re dedicated to bringing you the highest quality products at competitive prices. Let us be an integral part of your next project. WARRANTY POLICY Latham Australia Pty Ltd warrants to its purchasers that all products sold by it will upon delivery be free from defects in materials and workmanship. This warranty shall extend for a period of one (1) year following the date of shipment by us. Any claim in respect of a defective product must be made in writing prior to the expiration of the warranty period and must give particulars of the alleged defect. Subject to acceptance by us of the claim we agree to make good such defective product by repair or replacement (at our option) at our factory. All other costs whatsoever including the costs of disassembly and reinstallation and the cost of transport to and from our factory if applicable shall be borne by the purchaser.
Mechanical Expansion Joint Covers
Stair Tread Nosings
Neoprene-X-Pansion Loc and Tile Strips
Tactile Indicator Studs
Dock Bumpers
Wall Protection Systems
It is a fundamental condition of sale that all other warranties of any kind whether statutory or otherwise and whether express or implied are hereby excluded and that we accept no responsibility for consequential loss or damage of any kind. PUBLISHERS NOTE All sizes in this publication are shown in millimetres. The design and other information contained in this publication have been obtained from authoritative sources, which are believed to be correct in regard to the subject matter covered. The information provided is not exhaustive and is for guidance only. It is recommended that the user obtain independent professional advice for a particular installation or site condition(s).
Consult Your Local Latham Representative:
Latham Australia Pty Ltd expressly disclaims all and any liability to any user in respect of anything, and of the consequences of anything, done or omitted to be done by any such user in reliance upon the information contained in this publication. In the interests of quality and performance, we reserve the right to alter or change at anytime, any materials and specifications described in this publication. Batch colours and colours depicted in this publication are subject to variation. COPYRIGHT © 2021
Traffic Management Systems
5311-202102
All Design Rights Reserved.
Head Office: Latham Australia Pty Ltd ABN 87 000 502 296 14 Tennyson Road Gladesville 2111 NSW Australia Phone: (02) 9879 7888 Fax: (02) 9879 7666 International: +61 2 9879 7888 International: +61 2 9879 7666 www.latham-australia.com Email: sales@latham-australia.com DIRECT LINE TO YOUR LOCAL SUPPLIER: AUSTRALIA ONLY 1300 LATHAM (528426) / NEW ZEALAND FREECALL/FAX 0800 442 560