TRADEweld Welding machines, Consumables & Accessories 2019/2020

WELDING MACHINES, CONSUMABLES & ACCESSORIES

Page 1

WELDING BASICS

SELECT A WELDING OR CUTTING PROCESS Select the Process that matches the metals you want to weld or cut METAL TYPE

MMA STICK

MIG

FCAW

AC-TIG

DC-TIG

PLASMA

MODERATE

LOW

LOW

HIGH

HIGH

LOW

STEEL STAINLESS STEEL NICKLE ALLOYS ALUMINIUM CAST IRON COPPER BRASS TITANIUM MAGNESIUM ALLOYS ALL ELECTRICALLY CONDUCTIVE SKILL LEVEL

WELDING PROCESS

CUTTING PROCESS

WELDING & CUTTING PROCESSES MMA PROCESS • Most commonly called stick welding • Also known as MMA (manual metal arc), and SMAW (shielded metal arc welding) • MMA welders are ideal for General repairs and maintenance • Can weld in windy, outdoor conditions • Simple in operation & portable TIG WELDING PROCESS • TIG = tungsten inert gas welding • Provides high quality welds • Precise and accurate welding on thin material highly aesthetic weld beads • Capable of welding mild carbon steel, aluminum and other metals with just a single shielding gas, argon • For aluminuim welding an AC/DC TIG welder is required PLASMA PROCESS • Can cut any conductive metals • Neat precise cuts • Low heat affected zone which prevents warping • Works with compressed air

MIG WELDING PROCESS • MIG = metal inert gas welding - Argon (or MAG = metal active gas welding) CO2 • Easiest welding process to learn • Ideal for workshop or factory enviroments • Best suited for fabrication work • Welds up to 4 times faster than MMA welding • Not suitable for windy, outdoor conditions

FLUX CORED MIG WELDING PROCESS • FCAW = Flux Cored Arc Welding • Can be used without GAS or Gas assisted • Can weld in windy, outdoor conditions • Works as well as Stick on rusty or dirty material • Polarity needs to be reversed • Deeper penetration for welding thick sections • Increased metal deposition (easily two or three times that of Stick welding)

DUTY CYCLE EXPLAINED The duty cycle really details just how long the machine can operate within a TEN minute welding time without overheating or becoming damaged!

If your welding machine says ‘duty cycle =60% @ xyz amps’ this means that out of a welding ‘on-time’ of only ten minutes, your welder can only safely weld continuously for 6 minutes in every ten minutes, & if you exceed this 6 minutes, you will risk overheating or damaging your welder!

The ‘on-time’ is the actual welding time where a welding arc is being produced. The duty cycle is not relative to where your welder is only plugged in & switched on, but not being used.

IF A MACHINE OVERHEATS THE FOLLOWING STEPS NEED TO TAKE PLACE :

EXAMPLE – 60% DUTY CYCLE

Overheating

A or V

0

15

6 Minutes Welding

4 Minutes Resting

Minutes

OR Reduce Duty Cycle

WELDING LONGER THAN RATED DUTY CYCLE can damage machine and void warranty.

Page 2

Trade Brands SA

WELDING

TM

our new Industrial range consists of an MMA, three MIGs and three TIGs. Especially designed for tough conditions, our range will cope with most heavy duty fabrication.

You will find

ARC Machines TIG Machines MIG Machines

TM

Page 90 Page 90 Page 91

Manual metal arc (MMA) welding, also known as stick welding, is a manual arc welding process that uses a consumable electrode coated in flux to lay the weld. An electric current, in the form of either alternating current (AC) or direct current (DC) from a welding power supply, is used to form an electric arc between the electrode and the metals to be joined. As the weld is laid, the flux coating of the electrode disintegrates, giving off vapours that serve as a shielding gas and providing a layer of slag, both of which protect the weld area from atmospheric contamination.

Because of the versatility of the process and the simplicity of its equipment and operation, manual metal arc welding is one of the world’s most popular welding processes.

You will find

ARC Machines Safety Equipment ARC Acc & Cons.

Page 92 Page 106 Page 107

Welding Electrodes

111

Tungsten inert gas (TIG) welding, is an arc welding process that uses a consumable tungsten electrode to produce the weld.

The weld area is protected from atmospheric contamination by a shielding inert gas such as argon, and a filler rod is used. TIG is most commonly used to weld sections of stainless steel and non-ferrous metals such as aluminium, magnesium, and copper alloys. The process grants the operator greater control over the weld than competing processes such as (MMA) manual metal arc welding and (MIG) metal inert gas welding, allowing for stronger, higher quality welds. However, TIG is comparatively more complex and difficult to master, and furthermore, it is significantly slower than most other welding techniques.

You will find

TIG machines TIG Torches Consumables

Page 94 Page 95 Page 96

TIG Wire

Page 113

Metal Inert Gas (MIG) welding, also referred to as metal active gas (MAG) is an automatic or semi-automatic process in which a wire connected to a source of direct current acts as an electrode to join two pieces of metal as it is continuously passed through a welding gun. A flow of an inert (argon) gas or active gas (CO2) (depending on the type of steel), is also passed through the welding gun at the same time as the wire.

This gas acts as a shield, keeping airborne contaminants away from the weld zone. The primary advantage of MIG welding is that it allows metal to be welded much more quickly than traditional “stick welding” techniques. This makes it ideal for fabrication work.

You will find

MIG machines Multi process MIG Torches Consumables

Page Page Page Page

97 98 99 100

MIG Wire

Page 114

Plasma cutting is a process that is used to cut most types steels and alloys using a plasma machine & compressed air. The principle of plasma cutting is based on the ionisation of air which is forced through a small orifice (the cutting tip) and air electrode. An electric charge combined with the ionised air creates the cutting arc (plasma).

Plasma is an effective means of cutting thin and thick materials alike. Hand-held torches can usually cut up to 50 mm thick steel plate, depending on the size of the machine.

You will find

Plasma machines Plasma Torches Consumables Gas Equipment

Page Page Page Page

101 102 102 103

Page 3

WELDING LIMITED STOCKS

MMA 220V Inverter Welder

included

Manufactured to the highest standards using cutting edge inverter technology.

• Digital Display • MMA Mode with VRD control • Lift Tig Mode • Over Current and overheating protection • 35-50 Machine sockets • Robust construction

Welding Cable Set

included

Manufactured to the highest standards using cutting edge 50 KHZ high frequency CPU inverter technology.

Welding • Digital Display Cable Set • 32 Bit High Speed MCU control ( store welding Parameters) • TIG pulse mode • 4T / 2T Function • With Pre Flow > Arc start Current > Up TIG WP17 Torch slope > Peak Current > Base Current > Foot Remote Arc end Current > Downslope > Pulse Pedal Frequency > Pulse Ratio > Post flow > • Arc initiating: Clearance Width > AC Frequency H.F. Oscillating • Foot Pedal Control • Preflow gas: • MMA Mode with VRD control 0.1-1.0 • Over Current and overheating protection • Postflow gas: 0.1-15

TIG 380V Inverter Welder

INDUSTRIAL Use

included

Manufactured to the highest standards using cutting edge 50 KHZ high frequency CPU inverter technology.

• Digital Display Welding Cable Set • 32 Bit High Speed MCU control (Store welding parameters) • TIG pulse mode • 4T / 2T Function • With Pre Flow > Arc start Current > Up TIG WP26 Torch slope > Peak Current > Base Current > Foot Arc end Current > Downslope > Pulse Remote Pedal Frequency > Pulse Ratio > Post flow > • Arc initiating: Clearance Width > AC Frequency H.F. Oscillating • Foot Pedal Control • Preflow gas: • MMA Mode with VRD control 0.1-1.0 • Over Current and overheating protection • Postflow gas: 0.1-15

TIG 380V Inverter Welder

included

Manufactured to the highest standards using cutting edge 50 KHZ high frequency CPU inverter technology.

• Digital Display • 32 Bit High Speed MCU control (Store welding Parameters) • TIG pulse mode • 4T / 2T Function • With Pre Flow > Arc start Current > Up slope > Peak Current > Base Current > Arc end Current > Downslope > Pulse Frequency > Pulse Ratio > Post flow > Clearance Width > AC Frequency • Foot Pedal Control • MMA Mode with VRD control • Over Current and overheating protection

YEAR TM

WARRANTY

GENX MMA / GENX TIG INDUSTRIAL RANGE

INDUSTRIAL Use

INDUSTRIAL Use

Page 4

MMA 2000 INDUSPRO

PART NUMBER

MCOW4060

BARCODE

6003398094587

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA 1.6MM TO 4.0MM 15-200 27.6V 80%@200A 65V

VOLTS AMPS

220±15% 50/60HZ MMA: 27.6 / TIG: 24.0

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-485XW-290XH-380 10.3

MODEL

TIG 2000P DIGITAL ACDC

PART NUMBER BARCODE

EWM0130-I 6003398094594

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 1.6 - 4.0MM 6MM 5-200 20-180 18 27.2 60%@200A 56

VOLTS AMPS: TIG / MMA

220V±15% 50/60HZ 20.5 27.8

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-475XW-200XH-410 15

MODEL

TIG 2500P DIGITAL ACDC

PART NUMBER BARCODE

EWM0071-I 6003398094600

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2-5MM 8MM 5-250 20-230 20 30 60%@250A / 100% @ 194A 56

VOLTS AMPS: TIG / MMA

380V±15% 50/60HZ 9 12.9

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-520XW-245XH-580 33

MODEL

TIG 3200P DIGITAL ACDC

PART NUMBER BARCODE

EWM0072-I 6003398094617

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2-6MM 12MM 5-320 20-270 22.6 33 60%@315A / 100%@202A 56

VOLTS AMPS: TIG / MMA

380V±15% 50/60HZ 13 14.9

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-560XW-245XH-585 33.2

OUTPUT

INDUSTRIAL Use

TIG Inverters

MODEL

Welding Cable Set

TIG SR18W/C Torch Foot Remote Pedal

• Arc initiating: H.F. Oscillating • Preflow gas: 0.1-1.0 • Postflow gas: 0.1-15

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

WELDING included

INDUSTRIAL Use

MIG 380V Inverter welder

INDUSTRIAL Use

Welding Cable Set

MIG Torch

Spool gun connection, Spool size 5kg

Welding Cable Set

TIG Torch

MIG Torch

Spool gun connection, Spool size 5kg

included

Manufactured to the highest standards using cutting edge CPU inverter technology.

• Dual Digital Display • Multi process 3 in 1 • MIG mode • 4T / 2T Function • 15 Kg MIG Wire • 4 wheel Drive feed system • Polarity conversion output for Flux core wires • Aluminium Spool gun compatible • MMA Mode with VRD control • Lift TIG Mode • Overcurrent & overheating protection • 3 Duct Design Chassis design (Anti dust, anti corrosion, water resistant)

6003398094624

PROCESS WIRE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA 0.6 / 0.8 / 1.0MM MMA: 40-200/TIG: 15-200/MIG: 40-200 15-26V 60%@200A / 100%@160A 63V

VOLTS AMPS

220±15% 50/60HZ MMA: 21 / TIG: 28.0 / MIG: 37.4

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-450XW-218XH-370 20

MODEL

MIG 2800S INDUSPRO

PART NUMBER BARCODE

EWM0138-I 6003398094631

PROCESS VOLTS SOLID WIRE Ø FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 14-28V 0.6 /0.8 /1.0MM MMA: 25-250/TIG: 15-250/MIG:50-250 60%@250A 61

VOLTS AMPS

220V±15% 50/60HZ MMA: 18.5/MIG:51.6

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-900XW-520XH-765 51

MODEL

MIG 3200S INDUSPRO

PART NUMBER BARCODE

EWM0140-I 6003398094648

PROCESS VOLTS SOLID WIRE Ø FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 14-30V 0.8/1.0/1.2MM MMA: 25-300/TIG: 20-300/MIG:50-300 60%@300A 60

VOLTS AMPS

380V±15% 50/60HZ MMA: 58.4/TIG: 39/MIG: 51.6

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 23 L-900XW-520XH-765 52

OUTPUT

included

Manufactured to the highest standards using cutting edge CPU inverter technology.

• Dual Digital Display • Multi process 3 in 1 • MIG mode • 4T / 2T Function • 15 Kg MIG Wire • 4 wheel Drive feed system • Polarity conversion output for Flux core wires • Aluminium Spool gun compatible • MMA Mode with VRD control • Lift TIG Mode • Overcurrent & overheating protection • 3 Duct Design Chassis design (Anti dust, anti corrosion, water resistant)

EWM0134-I

BARCODE

Welding Cable Set

TIG Torch

MIG Torch

Spool gun connection, Spool size 15kg

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

GENX MIG INDUSTRIAL RANGE

MIG 220V Inverter welder

PART NUMBER

Page 5

WARRANTY

INDUSTRIAL Use

MIG 2200S DIGITAL

TM

Manufactured to the highest standards using cutting edge CPU inverter technology.

• Dual Digital Display • Multi process 3 in 1 • MIG semi synergic controlled • 4T / 2T Function • 5 Kg MIG Wire • 2 wheel drive feed system • Polarity conversion output for Flux core wires • Aluminium Spool gun compatible • MMA Mode with VRD control & Arc force • Lift TIG Mode • Overcurrent & overheating protection • Robust construction

MODEL

YEAR

MIG 220V Inverter Welder

WELDING AC Air Cooled

included

Manufactured to the highest standards using cutting edge Transformer Technology.

• Compact, lightweight and portable • AC current output • Excellent welding characteristics • Less power consumption • Robust construction

Hand Face Shield

YEAR WARRANTY

DIY Use included

Manufactured to the highest standards using advanced IGBT Technology.

• Compact, lightweight and portable • DC current output • Excellent welding characteristics • Less power consumption • Robust construction • Digital display • Touch panel amperage control YEAR

Hand Face Shield

Welding Cable Set

DIY to Light Engineering

MMA WELDING MACHINES

included

Manufactured to the highest standards using advanced IGBT Technology.

• DC current output • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display

PART NUMBER

MCOW4246

BARCODE

6003751032478

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA 1.6MM TO 3.2MM 130 17 10% 56V

VOLTS AMPS

220 28

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-353XW-170XH-232 16.5

MODEL

PRODIGI 2000

PART NUMBER

MCOW4095

BARCODE

6003398083154

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA 1.6MM TO 4.0MM 20-200 20 60% 57

VOLTS AMPS

220 32

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-353XW-170XH-232 16.5

MODEL

DIGITEC 150

DIGITEC 200

PART NUMBER

MCOW4050

MCOW4226

BARCODE

6003398087954

6003751359414

INPUT

GENERAL

OUTPUT

WARRANTY

DIGITEC IGBT DC Inverters

TX-130B1

OUTPUT

Welding Cable Set

IGBT DC Inverters

MODEL

Welding Cable Set

optional extras

SR17V TIG Torch

INPUT

GENERAL

OUTPUT

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA • ARGON TIG 1.6MM TO 3.2MM 20-145 18 60% 57

MMA • ARGON TIG 1.6MM TO 4.0MM 30-180 19 60% 57

VOLTS AMPS

220 24.5

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-230XW-142XH-315 5.6

FAN 21 L-220XW-135XH-350 6.25

MODEL

ARCPRO 1700

ARCPRO 2200

PART NUMBER

MCOW4051

MCOW4052

BARCODE

6003398087961

6003398087978

INPUT

220 29.5 GENERAL

YEAR WARRANTY

Argon Flowmeter

DIY to Light Engineering

ARC PRO IGBT DC Inverters

included

Manufactured to the highest standards using advanced IGBT Technology.

• DC current output • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Electronic Digital Display • 35 - 50 Machine sockets

Hand Face Shield

Welding Cable Set optional extras

DIY to Light Engineering

Page 6

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA 1.6MM TO 3.2MM 160 18 60% 57

VOLTS AMPS

220 26

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21S L-1060XW-450XH-936 3.2

MMA 1.6MM TO 4.0MM 200 20 60% 57

INPUT SR17V TIG Torch

220 32.1 GENERAL

YEAR WARRANTY

OUTPUT

Argon Flowmeter

FAN 21S L-1060XW-450XH-936 5

WELDING Industrial DC Inverters

included

Welding Cable Set

optional extras

SR17V TIG Torch

Argon Flowmeter

INDUSTRIAL Use

Industrial DC Inverters

YEAR WARRANTY

included

Inverter series is manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • ARC force control • Suitable for MMA & TIG scratch start welding • Excellent welding characteristics • Light weight and portable • Available in single or three phase • Less power consumption • Robust construction • Digital Display

INDUSTRIAL Use

Industrial DC Inverters

Welding Cable Set

optional extras

SR17V TIG Torch

Argon Flowmeter

Hand Shield

Welding Cable Set

optional extras

INDUSTRIAL Use

Industrial DC Inverters

included

Manufactured to the highest standards using cutting edge PWM & IGBT Technology.

• DC current output • Excellent welding characteristics • Dual voltage - 380 - 525V • Less power consumption • Robust construction • Digital Display • Weldsafe on/off switch

Hand Shield

Welding Cable Set

optional extras

SR17V TIG Torch

YEAR WARRANTY

INDUSTRIAL Use

MCOW4098

MCOW4099

BARCODE

6003751366306

6003751366313

OUTPUT

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA • TIG 1.6MM TO 3.2MM 20-160 26.2 60% 26.2

VOLTS AMPS

220 24.5

MMA • TIG 1.6MM TO 4.0MM 20-200 27.6 60% 27.6

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-230XW-142XH-315 5.6

FAN 21 L-247XW-162XH-364 6.8

MODEL

ARC 250S - 220V

ARC 250S - 380V

PART NUMBER

EWM0128-I

EWM0128-IL

BARCODE

6003398065365

6003398071250

INPUT

220 31.6

OUTPUT

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA • TIG 2.0MM TO 6.0MM 30-250 30 60% 60

VOLTS AMPS

220 58.4

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-720XW-255XH-420 17

MMA • TIG 2.0MM TO 6.0MM 30-250 30 60% 60

INPUT

380 14.4

Argon Flowmeter

FAN 21 L-720XW-255XH-420 17

MODEL

ARC400S DC - 380V

PART NUMBER

EWM0010-I

BARCODE

6003398065235

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA•GOUGING•TIG 2.0MM TO 6.0MM 20-400 36 60% 20

VOLTS AMPS

380 47.9

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-515XW-263XH-440 28

MODEL

ARC500S DC - 380/525V

PART NUMBER

EWM0013-I

BARCODE

6003398065266

PROCESS ELECTRODE SIZE AMPS VOLTS DUTY CYCLE OCV

MMA•GOUGING•ARGON 2.0MM TO 6.0MM 40-500 40 60% 20-88.5

VOLTS AMPS

380-525 38-27

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-865XW-385XH-680 67

OUTPUT

INPUT

SR17V TIG Torch

Argon Flowmeter

YEAR WARRANTY

PART NUMBER

GENERAL

included

Manufactured to the highest standards using cutting edge PWM & IGBT Technology.

• DC current output • ARC force control • Hot start control • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display

MMA 200S PWM

GENERAL

YEAR WARRANTY

MMA 160S PWM

MMA WELDING MACHINES

Inverter series is manufactured to the highest standards using advanced Mosfet Technology.

• DC current output • Suitable for MMA & TIG Scratch Start Welding.

• Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Generator safe - 7.5kw

MODEL

GENERAL

OUTPUT

INPUT

GENERAL

Page 7

WELDING TIG Inverters

YEAR

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • Suitable for MMA & TIG welding • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display • Precision weld Mild & Stainless Steel, Alloyed steel, carbon steel & copper • Use Argon Gas for MMA welding

WARRANTY

SEMI-INDUSTRIAL Use

TIG Inverters

YEAR

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• AC or DC current output • Suitable for MMA & TIG welding • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display • Suitable for MMA welding Aluminium, Alloyed steel, carbon steel & copper • Use with Argon gas

SEMI INDUSTRIAL Use

TIG WELDING MACHINES

TIG Inverters

YEAR

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• AC or DC current output • Suitable for MMA & TIG welding • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display • Suitable for MMA welding Aluminium, Alloyed steel, carbon steel & copper • Use with Argon gas

TIG Inverters

YEAR

SEMI INDUSTRIAL Use

Page 8

SR17 TIG Torch optional extras

Argon Flowmeter

Hand Shield

Welding Cable Set

SR17 TIG Torch SR17 TIGFoot Torch Remote Pedal optional extras

Argon Flowmeter

included

SEMI INDUSTRIAL Use

WARRANTY

Welding Cable Set

included

WARRANTY

WARRANTY

Hand Shield

Hand Welding Welding Shield CableCable Set Set

SR17 TIG Torch SR16 Foot Remote Pedal optional extras optional extras

Argon Flowmeter

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• AC or DC current output • Suitable for MMA & TIG welding • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Digital Display • Suitable for MMA welding Aluminium, Alloyed steel, carbon steel & copper • Use with Argon gas

Welding Cable Set Hand Welding Shield Cable Set

SR18 TIG Torch Foot SR17 TIGRemote Torch Pedal optional extras optional extras WRA300S water cooler Argon Flowmeter Argon Flowmeter

MODEL

TIG 200A HF DC

PART NUMBER BARCODE

MCOW4080 6003398053546

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2.0MM TO 4.0MM 6.0MM 10-200 30-200 18 27.2 60% 50-80

VOLTS AMPS

220 28

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-465XW-345XH-360 13.6

MODEL

TIG 200 HF AC/DC

PART NUMBER BARCODE

EWM0129-I 6003398065372

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2.0MM TO 4.0MM 6.0MM 10-200 30-200 18 27.2 60% 56

VOLTS AMPS

220 30

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-630XW-300XH-560 13.6

MODEL

TIG 250 HF AC/DC

PART NUMBER BARCODE

EWM0070-I 6003398065310

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2.0MM TO 5.0MM 8.0MM 10-250 30-250 20 30 60% 56

VOLTS AMPS

220 25

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-780XW-300XH-610 36

MODEL

TIG 315A HF AC/DC

PART NUMBER BARCODE

EWM0069-I 6003398065303

PROCESS ELECTRODE SIZE MAX STEEL THICKNESS AMPS: TIG / MMA VOLTS: TIG / MMA DUTY CYCLE OCV

TIG • MMA 2.0MM TO 6.0MM 12.0MM 10-315 30-315 22.6 32.6 60% 56

VOLTS AMPS

380 14.7

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-780XW-300XH-610 37

OUTPUT

INPUT

31

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

35

GENERAL

OUTPUT

INPUT

21.2

GENERAL

WELDING SR 17V x 4mt Tig Torch Valve (aircooled)

Code no: Barcode: EWTT00200 6003751364432

SR 17 x 4mt Tig Torch (aircooled)

• 150 Amp Valve operated Tig Torch • 60% Duty cycle • For use with DC inverter welders • Scratch start • Valve gas control • 10/25 connector • Regulator nut

• 150 Amp switch operated Tig Torch • 60% Duty cycle • For use with AC / DC TIG welders • HF start • Gas & power cable in one Code no: Barcode: EWTT00201 6003398057537

SEMI INDUSTRIAL Use

SEMI INDUSTRIAL Use

SR 26V x 4mt Tig Torch Valve (aircooled)

Code no: Barcode: EWTT00205 6003751364630

SR 26 x 4mt Tig Torch (aircooled) with switch

• 200 Amp Valve operated Tig Torch • 60% Duty cycle • For use with DC inverter welders • Scratch start • Valve gas control • 35/50 connector • Regulator nut

• 200 Amp switch operated Tig Torch • 60% Duty cycle • For use with AC / DC TIG welders • HF start • Gas & power cable in one Code no: Barcode: EWTT00207 6003398057582

SEMI INDUSTRIAL Use

SEMI INDUSTRIAL Use

SR 18 x 4mt Tig Torch (watercooled)

WRA-300S Watercooler

• Water cooled TIG torch • 240 Amp switch operated • 60% Duty cycle • For use with AC / DC TIG welders • HF start Code no: Barcode: EWTT00211 6003398057605

Must be used with Tradeweld WRS-300S Watercooler EWM0011-L

SEMI INDUSTRIAL Use

Consumable Assembly

• With interlocking capabilities for automated machinery

• 220 Volt • 15Lt Tank • Output: 11 L/Minute • Portable • Suitable for MIG , TIG & Plasma applications • With interlocking capabilities for automated machinery Code no: Barcode: EWM0011-L 6003398062463

Assembly instructions included in the manual

TRIGGER SWITCH EWTT00226 6003398057681

• Replacement trigger switch

BRAIDED GAS HOSE (PER mt)

OUTER COVER (PER mt) EWTT00271 6003398058107

EWTT00270 6003398058091

HOSE CLAMP 8.7mm (1 EAR)

HOSE CLAMP 11.3mm (1 EAR)

EWTT00258 EWTT00239 6003398057995 6003398057803

TIG Torch Heads

SR 17 TORCH HEAD

SR 17V TORCH HEAD

SR 26 TORCH HEAD

EWTT00220 6003398057629

EWTT00221 6003398057636

• Replacement torch head for EWTT00201

• Replacement torch head for EWTT00200

EWTT00222 6003398057643

• Replacement torch head EWTT00207

SR 26V TORCH HEAD

SR 18 TORCH HEAD

EWTT00223 6003398057650

• Replacement torch head EWTT00205

EWTT00219 6003398057612

• Replacement torch head EWTT00211

Sold Individually

TIG Torch Spares

SR 17/17V HANDLE EWTT00224 6003398057667

• Replacement handle

SR 26/26V & 18 HANDLE

SR 17/17V 2 PIECE POWER TIG HANDLE WP18-26 CABLE CONNECTOR

EWTT00248 EWTT00225 6003398057896 6003398057674 • Replacement

• Replacement handle

handle

EWTT00233 6003398057742

• Replacement cable connector for the torch head

SR 26/26V 2 PIECE POWER CABLE CONNECTOR EWTT00235 6003398057766

• Replacement cable connector for the torch head

Sold Individually

Page 9

TIG TORCHES & CONSUMABLES

TIG Torch Spares

WELDING TIG Consumables - 1.6mm, 2.4mm, 3.2mm • For welding Mild and Stainless steels

THORIATED TUNGSTENS (RED TIP) 1.6MM

THORIATED TUNGSTENS (RED TIP) 2.4MM

THORIATED TUNGSTENS (RED TIP) 3.2MM

EWTT00260 6003398058008

EWTT00261 6003398058015

EWTT00262 6003398058022

ZIRCONIATED TUNGSTENS (WHITE TIP) 1.6MM

ZIRCONIATED TUNGSTENS (WHITE TIP) 2.4mm

ZIRCONIATED TUNGSTENS (WHITE TIP) 3.2mm

EWTT00265 6003398058046

• For welding Aluminium

EWTT00266 6003398058053

EWTT00267 6003398058060

Sold Individually

TIG Starter Packs

TIG Starter Packs

ZIRCONIATED 1.6MM

THORIATED 1.6MM

STAINLESS STEEL STARTER PACK 1.6MM

ALUMINIUM STARTER PACK 1.6MM

EWPACTT002 6003398053690

EWPACTT004 6003398053720

STAINLESS STEEL STARTER PACK 2.4mm

ALUMINIUM STARTER PACK 2.4mm

EWPACTT003 6003398053713

EWPACTT005 6003398053737

EWPACTT039 6003398060124

EWPACTT042 6003398060148

THORIATED 2.4MM

ZIRCONIATED 2.4MM EWPACTT043 6003398060155

EWPACTT040 6003398054161

3 per

3 per

pack

pack

TIG Ceramic Pre-Packs

3 per

QUALITY

TIG ACCESSORIES & CONSUMABLES

3 per

QUALITY

pack

Welding Accessories

CERAMICS 10N50 NO. 4

QUALITY

pack

Welding Accessories

Welding Accessories

CERAMICS 10N49 NO. 5

EWPACTT023 6003398053812

EWPACTT020 6003398053782

3 per

CERAMICS 10N48 NO. 6 EWPACTT022 6003398053805

TIG Collett Pre-Packs

Welding Accessories

pack

COLLET 1.6MM

Welding Accessories

3 per

CERAMICS 10N47 NO. 7 EWPACTT021 6003398053799

3 per

QUALITY

pack

pack

Welding Accessories

CERAMICS 10N46 NO. 8 EWPACTT024 6003398060094

TIG Collett Body Pre-packs

5 per

QUALITY

QUALITY

pack

5 per

QUALITY

Welding Accessories

5 per

pack

QUALITY

Welding Accessories

COLLET 2.4MM

EWPACTT010 EWPACTT011 6003398053744 6003398053751

pack

COLLET 3.2MM

5 per

QUALITY

Welding Accessories

pack

COLLET BODIES

EWPACTT012 1.6mm EWPACTT015 6003398060063 6003398053768

TIG Torch Backup Pre-Packs

5 per

QUALITY

Welding Accessories

COLLET BODIES 2.4MM EWPACTT016

6003398053775

5 per

pack

QUALITY

Welding Accessories

pack

COLLET BODIES 3.2MM EWPACTT017

6003398060070

TIG Foot Remote Control for Inverter AC/DC MCOW4077 6003398071496

QUALITY

Welding Accessories

2 per

pack

BACK CAP SHORT

QUALITY

Welding Accessories

BACK CAP LONG

2 per

pack

EWTT00230 EWTT00231 6003398057711 6003398057728

Page 10

QUALITY

Welding Accessories

PREPACK TIG COMBO BACK CAP EWPACTT031 6003398053836

• All metal cast casing • Variable potentialmeter to control maximum amperage • Insulated metal braided cable

Suitable for TRADEWELD TIG200, 250 & 315 AC/DC

WELDING

YEAR WARRANTY

included

Manufactured to the highest standards using cutting edge Mosfet Technology.

• Internal 2 wheel wirefeed system • DC current output • Stepless voltage control • Excellent welding characteristics • Light weight and portable • Less power consumption • Robust construction • Ideal for light duty aluminium welding with a spool gun and fabrication work • Can carry a gas bottle

MIG Welders

YEAR

MIG 25 Torch optional extras

Mig Spool Gun SB 8

Argon Flowmeter

SEMI INDUSTRIAL Use

WARRANTY

Earth Cable

included

Manufactured to the highest standards using step controlled transformer Technology.

• Internal 4 wheel wirefeed system • DC current output • 3 Phase 380V • Stepless wire speed control • 10 Position voltage control • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for fabrication work • Can carry a gas bottle • Use with gas • Max 15kg MIG wire

Earth Cable

MIG 36 Torch

Argon Flowmeter

INDUSTRIAL Use

MIG Welders

YEAR WARRANTY

included

Manufactured to the highest standards using step controlled transformer Technology.

• Internal 4 wheel wirefeed system • DC current output • 3 Phase 380V • Stepless wire speed control • 30 Position voltage control • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for fabrication work • Can carry a gas bottle • Use with or without gas • Max 15kg MIG wire

INDUSTRIAL Use

MIG Welders

YEAR WARRANTY

INDUSTRIAL Use

Earth Cable

MIG 36 Torch

4mt Connection Cable

Argon Flowmeter

included

Manufactured to the highest standards using step controlled transformer technology.

• External 4 wheel wirefeed system • DC current output • Available in single and dual voltage • Stepless wire speed control • 30 Position voltage control • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for fabrication work • Can carry a gas bottle • Use with or without gas • Max 15kg MIG wire

Earth Cable

MIG 40 Torch

MODEL

MIG 250 SA

PART NUMBER BARCODE

EWM0126-I 6003398065341

PROCESS SOLID WIRE Ø MAX STEEL THICKNESS FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 0.8MM TO 1.0MM 0.8MM TO 10MM 250 60% 26.5

VOLTS AMPS

220 51.6

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-830XW-380XH-680 62

MODEL

MIG 325 C

PART NUMBER BARCODE

EWM0051-I 6003398068908

PROCESS SOLID WIRE Ø MAX STEEL THICKNESS FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 0.8MM TO 1.2MM 1.0MM TO 16MM 320 60% 17-38

VOLTS AMPS

380 20

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21S L-960XW-450XH-920 110

MODEL

MIG 365 S

PART NUMBER BARCODE

EWM0044-IL 6003398070871

PROCESS SOLID WIRE Ø MAX STEEL THICKNESS FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 0.9MM TO 1.2MM 1.6MM TO 20MM 1.0MM TO 1.6MM 350 60% 17-40

VOLTS AMPS

380 23

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21S L-1040XW-450XH-936 130

MODEL

MIG 505 S

MIG 505 SD

PART NUMBER BARCODE

EWM0028-IL 6003398070888

EWM0140-IL 6003398070895

PROCESS SOLID WIRE Ø MAX STEEL THICKNESS FLUX CORED WIRE Ø AMPS DUTY CYCLE OCV

MIG 1.0MM TO 2.0MM 2.0MM TO 20MM 1.0MM TO 3.2MM 500 60% 17-52

MIG 1.0MM TO 2.0MM 2.0MM TO 20MM 1.0MM TO 3.2MM 500 60% 17-52

VOLTS AMPS

380 41

380-525 47-32

FAN 21S L-1060XW-450XH-936 155

FAN 21S L-1060XW-450XH-936 158

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

4mt Connection Cable

Argon Flowmeter

GENERAL

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

Page 11

MIG WELDING MACHINES

MIG Welders

WELDING MIG Multi-Process Welders

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• Internal 2 wheel wirefeed system • DC current output • Suitable for MMA & MIG welding • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for light duty aluminium welding with a spool gun • Ideal for fabrication work • Max 5kg inside • Use with or without gas for MMA welding

Welding Cable Set

MIG 15 Torch optional extras

Mig Spool Gun SB 8

SR17V TIG Torch

MIG Multi-Process Welders

EWM0136M

BARCODE

6003398077177

PROCESS

MMA • MIG • TIG DC

SOLID WIRE Ø

0.8MM TO 1.0MM

MAX STEEL THICKNESS

0.8MM TO 8MM

FLUX CORED WIRE Ø

0.8MM TO 1.0MM

AMPS: MIG/MMA-TIG

30 - 200

DUTY CYCLE

35%

OCV: MIG/MMA-TIG

15.5 - 24

OUTPUT

30-160 61

VOLTS

220

AMPS

37.4

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-510XW-285XH-450 15

MODEL

MIG 200 W

PART NUMBER BARCODE

EWM0136-I 6003398066904

PROCESS

MMA • MIG • TIG DC

SOLID WIRE Ø

0.8MM TO 1.0MM

MAX STEEL THICKNESS

0.8MM TO 8MM

FLUX CORED WIRE Ø

0.8MM TO 1.0MM

AMPS: MIG/MMA-TIG

30 - 200

DUTY CYCLE

60%

OCV: MIG/MMA-TIG

15.5 - 24

GENERAL

Argon Flowmeter

DIY to Light Engineering

MIG 200 M

PART NUMBER

INPUT

YEAR WARRANTY

MODEL

included

MIG MULTI PROCESS MACHINES

OUTPUT

Manufactured to the highest standards using cutting edge Mosfet Technology.

• Internal 2 wheel wirefeed system • DC current output • Suitable for MMA & MIG welding • Stepless voltage control • Stepless wirefeed adjustment • Digital display • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for light duty aluminium welding with a spool gun • Ideal for fabrication work • Thermal protection • Fan cooled forced ventilation • Max 15kg MIG wire • Use with or without gas for MMA welding

Welding Cable Set

MIG 15 Torch optional extras

30-160 30-160

INPUT

Mig Spool Gun SB 8

SR17V TIG Torch

VOLTS

220

AMPS

37.4

COOLING

FAN

IP

21

DIMENSIONS (MM)

L-470XW-340XH-770

NET WEIGHT (KG)

18.2

MODEL

MIG 250 M

PART NUMBER

EWM0137-I

BARCODE

6003398066911

PROCESS

MMA • MIG • TIG DC HF

SOLID WIRE Ø

0.8MM TO 1.2MM

MAX STEEL THICKNESS

0.8MM TO 10.0MM

FLUX CORED WIRE Ø

-

GENERAL

Argon Flowmeter

YEAR WARRANTY

LIGHT Engineering

MIG Multi-Process Welders

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• Internal 2 wheel wirefeed system • DC current output • Excellent welding characteristics • Less power consumption • Robust construction • Ideal for light duty aluminium welding with a spool gun • Ideal for fabrication work • Max 15kg MIG wire • Can carry a gas bottle • Use with gas • TIG H.F. start DC • MMA welding

Welding Cable Set

SR26 TIG Torch

MIG 25 Torch optional extras

Mig Spool Gun SB 8

WARRANTY

Page 12

AMPS: MIG/MMA-TIG

50-250

DUTY CYCLE

60%

OCV

24

VOLTS

220

AMPS

51.6

COOLING

FAN

IP

21

DIMENSIONS (MM)

L-830XW-380XH-680

NET WEIGHT (KG)

62

INPUT

GENERAL

YEAR

SEMI-INDUSTRIAL use

OUTPUT

Argon Flowmeter

15-250

WELDING MIG 15 x 4mt Torch

Consumables for MIG 15 2 per

2 per

pack

QUALITY

QUALITY

pack

QUALITY

Welding Accessories

Welding Accessories

Welding Accessories

LINER 0.6 – 0.9MM X 4MT (BLUE)

EWB00355 6003398058503

• Euro style 150 Amp DC MIG torch • 60% Duty cycle Code no: Barcode: EWB00302 6003398058336

MIG 15 STARTER PACK

1 x MB15 Shroud 1 x MB15 Tip adaptor 5 x 0.9 M6 Contact tips EWPACB001 6003398053577

MIG 15 SWAN NECK

MIG 15 CONICAL SHROUDS

EWB00200 6003398058268

MIG 15 TIP ADAPTORS

EWPACC001H 6003398074107

EWPACT001H 6003398074114

For use with MIG machines MIG 175 EWM0135-I & MIG 200 EWM0126-I • Can be used on other makes of MIG welders

MIG 25 x 4mt Torch

Consumables for MIG 25 2 per

2 per

pack

QUALITY

Welding Accessories

QUALITY

pack

QUALITY

Welding Accessories

Welding Accessories

LINER 1.0 – 1.2MM X 4MT (RED)

EWB00356 6003398058510

• Euro style 230 Amp DC MIG torch • 60% Duty cycle Code no: Barcode: EWB00304 6003398058350

MIG 25 STARTER PACK

1 x MB25 Shroud 1 x MB25 Tip adaptor 5 x 1.0 M6 Contact tips EWPACB002 6003398058893

MIG 25 SWAN NECK

MIG 25 CONICAL

MIG 25 TIP ADAPTORS

EWB00201 SHROUDS 6003398058275 EWPACC002 6003398058954

EWPACT002 6003398059982

MIG 36 x 4mt Torch

Consumables for MIG 36

2 per

LINER 1.0 – 1.2MM X 4MT (RED)

QUALITY

Welding Accessories

pack

2 per

QUALITY

Welding Accessories

pack

2 per

QUALITY

Welding Accessories

pack

2 per

pack

QUALITY

Welding Accessories

EWB00356 6003398058510

• Euro style 350 Amp DC MIG torch • 60% Duty cycle Code no: Barcode: EWB00306 6003398058374

MIG 36 SWAN NECK

MIG 36 CONICAL

EWB00202 SHROUDS 6003398058282 EWPACC003 6003398058961

MIG 36 GAS DIFFUSERS

EWPACG001 6003398059463

MIG 36 TIP ADAPTORS M6

MIG 36 TIP ADAPTORS M8

EWPACT006 60033980600025

EWPACT003 6003398059999

For use with MIG machines MIG 325C EWM0051-I, MIG 365S EWM0044-IL & MIG 400 EWM0019-L • Can be used on other makes of MIG welders

MIG 40 x 4mt Torch

Consumables for MIG 40

2 per

LINER 1.0 – 1.2MM X 4MT (RED)

QUALITY

Welding Accessories

pack

2 per

QUALITY

Welding Accessories

pack

2 per

QUALITY

Welding Accessories

pack

EWB00356 6003398058510

• Euro style 400 Amp DC MIG torch • 60% Duty cycle Code no: Barcode: EWB00307 6003398058381

LINER 1.2 – 1.6MM X 4MT (YELLOW)

EWB00357 6003398058527

MIG 40 SWAN NECK

MIG 40 CONICAL SHROUDS

EWB00204 EWPACC004 603398058978 6003398058305

MIG 40 GAS DIFFUSERS

EWPACG002 603398059470

MIG 40 TIP ADAPTORS

EWPACT004 6003398060001

For use with MIG machines MIG 500S EWM0028-IL & MIG 505SD EWM0140-IL • Can be used on other makes of MIG welders

Page 13

MIG TORCHES & CONSUMABLES

For use with MIG machines MIG 250SA EWM0126-I & MIG 250M EWM0137- I • Can be used on other makes of MIG welders

WELDING MIG 501 x 4mt Torch

Consumables for MIG 501 2 per

pack

QUALITY

Welding Accessories

2 per

2 per

pack

QUALITY

QUALITY

Welding Accessories

pack

Welding Accessories

LINER 1.0 – 1.2MM X 4MT (RED)

EWB00356 6003398058510

• Euro style 500 Amp DC MIG torch • 80% Duty cycle Water Cooled Code no: Barcode: EWB00309 6003398058404

•

LINER 1.2 – 1.6MM X 4MT (YELLOW)

EWB00357 6003398058527

MIG 501 SWAN NECK

MIG 38/501 MIG 38/501 CONICAL SHROUDS GAS DIFFUSERS

EWB00205 EWPACC005 6003398058312 6003398058985

EWPACG003 6003398059487

MIG 38/501 TIP ADAPTORS EWPACT005 6003398060018

For use with water cooler • Can be used on other makes of MIG welders

Consumables for MIG Spool Gun SB 8

SB 8 MIG Spool Gun

QUALITY

Welding Accessories

SPOOL GUN – NOZZLE / SHROUD SPOOL GUN STARTER PACK

EWSB8-03-11 6003398069097

SPOOL GUN – LINER ASSEMBLY EWSB8-03-06 6003398069066

SPOOL GUN – TIP ADAPTOR

EWSB8-03-02 6003398069103

EWPACB008 6003398071199

• Euro style 130 Amp DC MIG Spool Gun • 30% Duty cycle

5 per

pack

QUALITY

Welding Accessories

SPOOL GUN CONTACT TIPS

Code no: Barcode: EWB00040 6003398058251

MIG TORCHES & CONSUMABLES

•

EWPACB009 6003398073438

MIG SB8 CONTACT TIP

EWSB-03-01 6003398069585

SPOOL GUN – GUN ROLLER

EWSB8-02-13 6003398069011

SPOOL GUN – TRIGGER ASSEMBLY EWSB8-04-00 6003398071472

For use with MIG machines EWM0135-I, EWM0136-I, EWM0137-I, EWM0126-I •Ideal for welding Aluminium

M6 Contact Tip Pre-packs 5 per

QUALITY

Welding Accessories

0.8MM

EWPACCT001H 6003398074121

M8 Contact Tip Pre-packs

0.9MM

pack

EWPACCT002 6003398053614

QUALITY

Welding Accessories

5 per

pack

0.8MM

EWPACCT0010 6003398058992

0.9MM

EWPACCT0011 6003398059005

1.0MM

1.0MM

1.2MM

1.2MM

EWPACCT003H 6003398074138 EWPACCT004 6003398053638

EWPACCT0012 6003398059012 EWPACCT0013 6003398059029

MIG Torch Spares 2 per

pack

LINER RETAINING NUT (ALL EURO TORCHES)

POLYCARBON LINER COLLET

EWB00361 6003398058565

MIG Torch Spares

EWB00364 6003398058596

TRIGGER SWITCH

EWB00433 6003398058794

Liners LINER 0.6 – 0.9MM X 4MT (BLUE)

EWB00355 6003398058503

LINER 1.0 – 1.2MM X 4MT (RED)

EWB00356 6003398058510

HANDLE COMPLETE (FITS MB15, MB25 & MB36) EWB00434 6003398058800

Page 14

LINER 1.2 – 1.6MM X 4MT (YELLOW) EWB00357 6003398058527

LINER POLYCARBON 1.2MM (SOLD PER MT) EWB00359 6003398058541

WELDING Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • Excellent cutting characteristics • Less power consumption • Robust construction • Ideal for cutting Mild, Stainless, Aluminium, Brass & Copper • Built-in water trap • No compressor required • Built-in oilless air compressor

included

Earth Cable

PT31 Plasma Torch

YEAR WARRANTY

INDUSTRIAL Use

PLASMA Cutter

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • Excellent cutting characteristics • Less power consumption • Robust construction • Ideal for cutting Mild, Stainless, Aluminium, Brass & Copper • Built-in water trap • Min compressor required: 50L

Earth Cable

PT31 Plasma Torch

YEAR WARRANTY

INDUSTRIAL Use

PLASMA Cutter

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • Excellent cutting characteristics • Less power consumption • Robust construction • Ideal for cutting Mild, Stainless, Aluminium, Brass & Copper • Built-in water trap • Min compressor required: 100L • 3 Phase

Earth Cable

P60 Torch

YEAR WARRANTY

INDUSTRIAL Use

PLASMA Cutter

included

Manufactured to the highest standards using cutting edge PWM & Mosfet Technology.

• DC current output • Excellent cutting characteristics • Less power consumption • Robust construction • Ideal for cutting Mild, Stainless, Aluminium, Brass & Copper • Built-in water trap • Min compressor required: 100L • 3 Phase YEAR WARRANTY

INDUSTRIAL Use

Earth Cable

MODEL

CUT 40K

PART NUMBER BARCODE

MCOW4082B 6003398077184

PROCESS HIGH FREQUENCY MAX STEEL THICKNESS

PLASMA TOUCH START 0.6MM TO 10MM

AMPS DUTY CYCLE OCV

40 60% 230

VOLTS AMPS

220 47

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-410XW-195XH-590 27

MODEL

CUT 40H

PART NUMBER BARCODE

MCOW4082 6003398053553

PROCESS HIGH FREQUENCY MAX STEEL THICKNESS PRESSURE AMPS DUTY CYCLE OCV

PLASMA TOUCH START 0.6MM TO 5MM 4.5 BAR 40 60% 230

VOLTS AMPS

220 30

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-485XW-195XH-320 9

MODEL

CUT 60H

PART NUMBER BARCODE

EWM0131-I 6003398065396

PROCESS HIGH FREQUENCY MAX STEEL THICKNESS PRESSURE AMPS DUTY CYCLE OCV

PLASMA PILOT ARC START 1.0MM TO 20MM 4.5 BAR TO 5.5 BAR 60 60% 295

VOLTS AMPS

380 12

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-450XW-190XH-345 19

MODEL

CUT 100H

PART NUMBER BARCODE

EWM0132-I 6003398065402

PROCESS HIGH FREQUENCY MAX STEEL THICKNESS PRESSURE AMPS DUTY CYCLE OCV

PLASMA PILOT ARC START 1.0MM TO 30MM 4.5 BAR TO 5.5 BAR 100 60% 295

VOLTS AMPS

380 23.1

COOLING IP DIMENSIONS (MM) NET WEIGHT (KG)

FAN 21 L-635XW-455XH-515 19

P80 Torch

OUTPUT

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

OUTPUT

PLASMA CUTTERS

PLASMA Cutter with Built-in Air Compressor

INPUT

GENERAL

OUTPUT

INPUT

GENERAL

Page 15

WELDING PT 31 Plasma Torch x 5M

Consumables for PT 31 (CUT 40 H) 5 per

Welding Accessories

Welding Accessories

• Plasma torch for Cut 40 H MCOW4082 • 60% Duty cycle @ 40 Amp • Touch start /drag cutting Code no: Barcode: EWP0200 6003398056905

STARTER PACK SHORT

5 per

pack

QUALITY

QUALITY

Welding Accessories

Welding Accessories

5 per

QUALITY

Welding Accessories

EWPACP0031H 6003398074183

5 per

pack

QUALITY

5 per

pack

QUALITY

Welding Accessories

pack

DIFFUSERS

EWPACP0020H 6003398074145

EWPACP0040H 6003398074152

Welding Accessories

QUALITY

ELECTRODES SHORT

TIPS SHORT

EWPACP001 6003398053645

5 per

pack

QUALITY

QUALITY

Welding Accessories

pack

Consumable assembly

STARTER PACK LONG

TIPS LONG

EWPACP001L 6003398071441

ELECTRODES LONG

EWPACP0040LH 6003398074176

PT 31 TORCH HEAD

EWP0206 6003398056967

EWTT00226T 6003398084588

Consumables for P60 (CUT 60 H) 5 per

Welding Accessories

PLASMA TORCHES & CONSUMABLES

PT 31SWITCH

EWP0205 6003398056950

5 per

pack

QUALITY

• Plasma torch for Cut 60 H EWM0131-I • 60% Duty cycle @ 60 Amp • H.F start

EWPACP0010 6003398053676

PT 31 HANDLE

• Replacement parts for PT 31 • Handle not included

P60 Plasma Torch x 4M

SHIELD CUPS

EWPACP0020LH 6003398074169

QUALITY

Welding Accessories

5 per

pack

QUALITY

QUALITY

Welding Accessories

Welding Accessories

pack

P 60 STARTER PACK

EWPACP002 6003398059715

P 60 ELECTRODES

P 60 TIPS 1.2MM EWPACP0041 6003398059821

Code no: Barcode: EWP0210 6003398056974

P 60 SHIELD CUPS

EWPACP0021 6003398059722

EWPACP0011 6003398059661

5 per

Consumable assembly

pack QUALITY

Welding Accessories

P 60 TORCH HEAD

EWP0215 6003398057025

EWP0227 6003398057100

EWPACP011G 6003398084595

P80 Plasma Torch x 5M

Consumables forP80 (CUT 100 H) 5 per

QUALITY

pack

Code no: Barcode: EWP0220 6003398057032

P80 SHIELD CUPS EWPACP0012 6003398059678 SINGLES: EWP0222 6003398057056

5 per

QUALITY

pack

Welding Accessories

Welding Accessories

• Plasma torch for Cut 100 H EWM0132-I • 60% Duty cycle @ 100 Amp • H.F start

P80 TIPS 1.3MM each

EWPACP0048 6003398059890 SINGLES: EWP0226 6003398057094

5 per

QUALITY

5 per

pack

QUALITY

Welding Accessories

each

EWPACP0042 6003398059838 SINGLES: EWP0221 6003398057049

pack

Welding Accessories

P80 TIPS 1.5MM

Consumable assembly

P 80 ELECTRODES each

EWPACP0022 6003398059739 SINGLES: EWP0223 6003398057063

each

P 80 TORCH HEAD P 80 GUIDE WHEEL EWP0224 6003398057070

Page 16

• Replacement parts for P60 • Handle not included

P 60 / P 80 HANDLE

P 60 GUIDES

EWP0225 6003398057087

• Replacement parts for P 80 • Handle not included

WELDING Argon Flowmeter

Single Stage Regulator - Acetylene

Suitable for argon and mixed argon gas • For use on MIG and TIG welder

Single Stage Regulator - Oxygen

Code no: Barcode: EWREG0003 6003751019974

• Forged brass body for maximum strength • Easy to read Gauges • Large 70mm Diaphragm for sufficient Acetylene flow to cut 300mm • Sintered Metal inlet filter to trap impurities • Max. delivery pressure (bar): 1.4 • Working pressure (bar): 0-2.5 • Cylinder pressure (bar): 0-40

Suitable for gas welding, heating and cutting

Gas Combination Kit

• Forged brass body for maximum strength • Easy to read Gauges • Large 70mm Diaphragm for sufficient oxygen flow to cut 300mm • Sintered Metal inlet filter to trap impurities • Max. delivery pressure (bar): 7.0 • Working pressure (bar): 0-16 • Cylinder pressure (bar): 0-315

Contents: • Single stage oxygen regulator • Swaged nozzles 3, 5, 7 • Single stage acetylene regulator • Flash back arrestors (Regulator mount) • Handle / Shank • Nozzle cleaner • Mixer • Triple flint Lighter • ANM 1.2mm cutting nozzle • Goggles • Twin hose • O ring set • Weld up to 9mm & Cut up to 200mm

Code no: Barcode: EWREG0004 6003398053867

Code no: Barcode: EWCUT0001 6003398057117

Suitable for gas welding, heating and cutting

Heavy duty outfit for cutting, Heating, Gouging, Welding, Soldering Brazing and Hardfacing.

Complete One Piece Gas Cutting Torch (Saffire Style)

Code no: EWREG0006

Barcode: 6003398053843

• Cutting capacity – 3mm to 300mm • Head and body in forged brass for maximum strength • Torch is 500mm long • Head at 90º bend • In line stainless steel gas tubes for better heat and backfire resistance • Aluminium handle • Stainless steel lever • Uses ANM / ANME / PNM / PNME nozzles

Conforms to EN ISO 5172

• Cutting capacity – 3mm to 200mm • Head and body in forged brass for maximum strength • In line stainless steel gas tubes for better heat and backfire resistance • Stainless steel lever • Uses ANM/ ANME/ PNM/ PNME nozzles

Code no: Barcode: EWCUT0002 6003398057124

Must be used with EWCUT0003

Handle/ Shank (Saffire Style)

Code no: Barcode: EWCUT0003 6003398057131

Mixer (Saffire Style) • Weld up to 9mm and Cut up to 200mm • In line stainless steel gas tubes for better heat and backfire resistance • Aluminium handle

Can be used with EWCUT0002 & EWREG0015

Nozzle Cleaners

• Must be used with EWCUT0003 • Uses Swaged nozzles 3, 5, 7

Code no: Barcode: EWREG0015 6003398057506

Must be used with EWCUT0003

Triple Flint Lighters

Code no: Barcode: EWC0100 6003398060490 EWCP0100 6003398070529 (PRE-PACK)

Triple Flint Renewals • Easy operation gas lighter • Triple head for long life

• Assortment of pin files for cleaning nozzles

Sold individually

Cutting Attachment (Saffire Style)

Code no: Barcode: EWC0101 6003398060506 EWCP0101 6003398070505 (PRE-PACK)

• Replacement head for triple flint lighter Code no: EWC0102 EWCP0102

Barcode: 6003398060513 (1’S) 6003398070512 (PRE-PACK) 3’S

Sold individually

Page 17

GAS EQUIPMENT

Code no: Barcode: EWREG0013 6003751364098

• Forged brass body for maximum strength and safety • Easy to read tube and 53mm Gauge (bar/psi or kpa/psi) • Virtually unbreakable • Max flow rate 25lpm • Transparent polycarbonate outer tube for added strength and visibility • Sintered bronze inlet filter to trap impurities • Reliable external safety relief valve

WELDING Swagged Brazing Nozzles

MODEL

No. 3

No. 5

No. 7

PART NUMBER BARCODE

EWNOZ0022 6003398057346

EWNOZ0021 6003398057339

EWNOZ0023 6003398057353

TIP SIZE MATERIAL THICKNESS OXYGEN PRESSURE ACETYLENE PRESSURE

3 2 mm 1 (bar) 0.15 (bar)

5 2.6 mm 1 (bar) 0.15 (bar)

7 3.2 mm 1 (bar) 0.15 (bar)

Pre-Packs • Swaged tips forged in copper • Excellent welding characteristics

SWAGED NOZZLE 3

1 per

1 SWAGED pack NOZZLE 5 per

pack

EWPACGC040 6003398059654

EWPACGC041 6003398073414

SWAGED NOZZLE 7

1 per

pack

EWPACGC042 6003398073421

Can be used with EWCUT0003 & EWREG0015

ANM Cutting Nozzles

• Oxy Acetylene short cutting nozzles

MODEL

0.8mm (1/32)

1.2mm (3/64)

1.6mm (1/16)

1.9mm (5/64)

2.4mm (3/32)

2mm (1/8)

PART NUMBER BARCODE

EWNOZ0001 6003398057155

EWNOZ0002 6003398057162

EWNOZ0003 6003398057179

EWNOZ0004 6003398057186

EWNOZ0005 6003398057193

EWNOZ0006 6003398057209

LENGTH CUTTING THICKNESS OXYGEN PRESSURE ACETYLENE PRESSURE

88 mm 1-5 mm 1.5 (bar) 0.5 (bar)

88 mm 5-10 mm 2.0 (bar) 0.5 (bar)

88 mm 10-30 mm 2.5 (bar) 1.0 (bar)

88 mm 30-60 mm 3.0 (bar) 1.0 (bar)

88 mm 60-100 mm 3.5 (bar) 1.5 (bar)

88 mm 100-200 mm 4.0 (bar) 1.5 (bar)

Pre-Packs

3 per

1 per

ANM CUTTING NOZZLE 0.8MM

pack

pack

EWPACGC003 6003398053898

ANM CUTTING NOZZLE 0.8MM

1 per

pack

EWPACGC003H 6003398074190

ANM CUTTING NOZZLE 1.2MM

1 per

pack

EWPACGC004 6003398053904

ANM CUTTING NOZZLE 1.6MM

EWPACGC005 6003398053911

Can be used with EWREG0006 & EWCUT0002

ANME Cutting Nozzles

MODEL

0.8mm (1/32)

1.2mm (3/64)

1.6mm (1/16)

1.9mm (5/64)

2.4mm (3/32)

2mm (1/8)

PART NUMBER BARCODE

EWNOZ0010 6003398057223

EWNOZ0011 6003398057230

EWNOZ0012 6003398057247

EWNOZ0013 6003398057254

EWNOZ0014 6003398057261

EWNOZ0007 6003398057216

LENGTH CUTTING THICKNESS OXYGEN PRESSURE ACETYLENE PRESSURE

88 mm 1-5 mm 1.5 (bar) 0.5 (bar)

88 mm 5-10 mm 2.0 (bar) 0.5 (bar)

88 mm 10-30 mm 2.5 (bar) 1.0 (bar)

88 mm 30-60 mm 3.0 (bar) 1.0 (bar)

88 mm 60-100 mm 3.5 (bar) 1.5 (bar)

88 mm 100-200 mm 4.0 (bar) 1.5 (bar)

MODEL

0.8mm (1/32)

1.2mm (3/64)

1.6mm (1/16)

2.4mm (3/32)

3.2mm (1/8)

PART NUMBER BARCODE

EWNOZ0015 6003398057278

EWNOZ0016 6003398057285

EWNOZ0017 6003398057292

EWNOZ0019 6003398057315

EWNOZ0020 6003398057322

LENGTH CUTTING THICKNESS OXYGEN PRESSURE PROPANE PRESSURE

76 mm 1-5 mm 1.5 (bar) 0.5 (bar)

76 mm 5-10 mm 2.0 (bar) 0.5 (bar)

76 mm 10-30 mm 2.5 (bar) 1.0 (bar)

76 mm 60-100 mm 3.5 (bar) 1.5 (bar)

76 mm 100-200 mm 4.0 (bar) 1.5 (bar)

• Oxy Acetylene Long cutting nozzles

Can be used with EWREG0006 & EWCUT0002

GAS CONSUMABLES

PNM Cutting Nozzles

• Oxy Propane short cutting nozzles • Two piece nozzles

Pre-Packs

3 per

pack

PNM CUTTING NOZZLE 0.8MM

1 per

pack

EWPACGC010 6003398059494

PNM CUTTING NOZZLE 1.2MM

EWPACGC011 6003398059500

1 per

pack

PNM CUTTING NOZZLE 1.6mm

1 per

pack

EWPACGC012 6003398059517

PNM CUTTING NOZZLE 1.9MM

EWPACGC013 6003398059524

Can be used with EWREG0006 & EWCUT0002

PNME Cutting Nozzles

MODEL

0.8mm (1/32)

1.2mm (3/64)

1.6mm (1/16)

2.0mm (5/64)

2.4mm (3/32)

3.2mm (1/8)

PART NUMBER BARCODE

EWNOZ0025 6003398057360

EWNOZ0026 6003398057377

EWNOZ0027 6003398057384

EWNOZ0028 6003398057391

EWNOZ0029 6003398057407

EWNOZ0031 6003398057421

LENGTH CUTTING THICKNESS OXYGEN PRESSURE PROPANE PRESSURE

92 mm 1-5 mm 1.5 (bar) 0.5 (bar)

92 mm 5-10 mm 2.0 (bar) 0.5 (bar)

92 mm 10-30 mm 2.5 (bar) 1.0 (bar)

92 mm 30-60 mm 3.0 (bar) 1.0 (bar)

92 mm 60-100 mm 3.5 (bar) 1.5 (bar)

92 mm 100-200 mm 4.0 (bar) 1.5 (bar)

• Oxy Propane long cutting nozzles • Two piece nozzles

Can be used with EWREG0006 & EWCUT0002

Page 18

WELDING Torch Mounted Flashback Arrestor 3/8

Regulator Mounted Flashback Arrestor 3/8

• Protection against flashback & gas reverse flow • Spring loaded non return valve • Sintered stainless steel flame arrestor Barcode:

Code no:

EWREG0001 ACETYLENE EWREG0005 OXYGEN

Description:

6003398057452 6003398057476

EWREG0016 ACETYLENE EWREG0002 OXYGEN

6003398057513 6003398057469

Pre-Packs

FLASHBACK ARRESTORS TORCH MOUNTED (QTY 1 OXY & 1 ACET)

Pre-Packs

FLASHBACK ARRESTORS REGULATOR MOUNTED (QTY 1 OXY & 1 ACET)

1 per

pack

1 per

pack

Description:

Barcode:

1 per

pack

1 per

pack

EWPACGC001 6003398053874

For use with Tradeweld gas torches and regulators

EWPACGC002 6003398053881

For use with Tradeweld gas torches and regulators

Oxygen Hose 8mm (Blue)

Acetylene Hose 8mm (Red) • 8mm inner diameter reinforced hose

• 8mm inner diameter reinforced hose

Code no: Barcode: EWCAB0020 6003398062272

Code no: Barcode: EWCAB0021 6003398062289

Sold per meter

Sold per meter

Hose Fittings

Pre-Packs - Hose Fittings • Replacement nuts and tailpieces for oxygen and acetylene hose

Code no:

Description:

EWTT00238 EWTT00244 EWTT00243

OXYGEN NUT R/H 3/8 6003398057797 ACETYLENE NUT L/H 3/8 6003398057858 TAILPIECE 8MM 6003398057841

• Replacement nuts and tailpieces for oxygen and acetylene hose

Barcode: Code no: Barcode: EWPACGC035 6003398059647

Sold individually

Sold per Set

Y Piece Connector

Straight Line Cutting Machines • For operating two gas lines from one regulator

• Includes 1.8m track Code no:

Description:

Barcode:

EWNOZ0040 OXYGEN 6003398057438 EWNOZ0041 ACETYLENE 6003398057445

Suitable for use on the Tradeweld flowmeters

• Compact straight line cutter • Durable aluminium design • Forward and reverse function • Supplied with cutting torch & 1.8m Track • Extra tracks available

Code no:

Description:

EWM0127-L EWM0129-L

BOD-30 AUTO CUTTING MACHINE (BEETLE) 6003398062944 EXTRA RAIL FOR CUTTING MACHINE 1.8M 6003398062968

Barcode:

For use with Gas cutting

GAS CONSUMABLES & ACCESSORIES

Code no:

• Protection against flashback & gas reverse flow • Spring loaded non return valve • Sintered stainless steel flame arrestor

Pre-packed Brazing Rods Solid carbon steel Supplied in straight cut lengths

12 per pack

CCR 3.0MM

TOOW4292 6003751031570

Suited for sheet metal work such as motor bodies, tubular & galvanized iron fabrication as well as for copper & for brazing cast iron, & heavy steel sections. May be used for fusion-weld brass

BBR 2.0MM

TOOW4293 10 per 6003751031587 pack

BBR 3.0MM

TOOW4294 6003751031594

6 per

pack

BBR FLUX COATED 3.0MM TOOW4295 6003751031600

5 per

pack

Used in the repair of automotive parts, pipes, tanks, trailers, refrigeration equipment, aluminium casting, and structural shapes

ALUMINIUM GAS BRAZING 1.6MM TOOW4296 6003751031617

20 per pack

ALUMINIUM GAS BRAZING 3.2MM TOOW4297 6003398069509

14 per pack

Widely used as a general purpose silver brazing filler metal as well as in joining copper to steel in refrigeration pipe work

SILVER SOLDER BARE 1.5MM

2 per

Flux coated silver brazing type alloy for joining all ferrous and copper metals, stainless steel, nickel and its alloys, steel castings, malleable and cast iron, tungsten carbides

SILVER SOLDER FLUX COATED 1.5MM

COPPER TEC 2.0MM TOOW4308 6003751031723

8 per

pack

TOOW4306 TOOW4307 2 per pack 6003751031709 6003751031716 pack COPPER TEC 3.0MM TOOW4309 4 per pack 6003751031730

ALUMINIUM FLUX 50G

TOOW4303 6003751031693

Suitable for brazing

Page 19

WELDING NON ADJUSTABLE

FULLY ADJUSTABLE

• Auto darkening lens is ANSI approved • Viewing area: 30mm x 88mm • Cartridge Size: 110mm x 90mm x 9mm • Light State: DIN 4 • Dark State: Variable Shade: 9 - 11 - 13 • Switch Time: 1/10 000s • Light to Dark: 0.25 - 0.45s • Adjustable Shade Control: 9 - 11 - 13 (Selector On Cartridge) • Power On/Off: Automatic • Power Supply: 2 x AAA • Alkaline 1.5V Batteries • Arc Sensor: 1 • Operating Temperature: -5ºC +55ºC • Storing Temperature: -20ºC +70ºC Code no: Barcode: EWHEL0001 6003398083130

Replacement Lenses EWLENS011B 6003398109847 EWLENS013 6003398075159 EWLENS012 6003398075142

• INNER CLEAR LENS 001/005 • OUTER CLEAR LENS 001/005 • AUTO DARKENING FILTER LENS 001/005

WELDING FACE SHIELDS YEAR

WARRANTY

Code no: Barcode: EWHEL0005 6003398060605

Replacement Lenses

• INNER CLEAR LENS 020 • OUTER CLEAR LENS 020

• Auto darkening lens is ANSI approved • Viewing area: 90 x 35mm • Cartridge size: 110 x 90 x 9mm • Arc sensor: 2 • Light state: DIN 4 • Dark state: Variable shade 9-13 • Shade control: external, variable • Power on/off: fully automatic • Sensitivity control: low - high, by control dial • UV/IR protection: DIN16 • Power supply: Solar cell 2 x AAA alkaline • Battery change required • Switching time: 1/15000s (light to dark) • Dark to light: Min - max, by control dial • Low amp. TIG: >10 amps(DC), 10 amps(AC) • Grinding function: yes • Low volume alarm: yes • ADF self check: yes • Operating temp: Code no: Barcode: -5ºC~+55ºC • Storing temp: -20ºC~+70ºC EWHEL0006 6003398060612

Replacement Lenses • INNER LENS 001/005 • OUTER CLEAR LENS 001/005 • AUTO DARKENING FILTER LENS 001/005

Ideal for MIG , STICK & TIG welding

EWLENS010 EWLENS011 EWLENS018

6003398060728 6003398088272 6003398075203

• INNER LENS 006 • OUTER LENS 006 • AUTO DARKENING FILTER LENS 007

Ideal for MIG , STICK & TIG welding and grinding

FULLY ADJUSTABLE euro style

FULLY ADJUSTABLE • Auto darkening lens is ANSI approved • Viewing area: 92 x 42mm • Cartridge size: 110 x 90 x 10mm • Arc sensor: 2 • Light state: DIN 4 • Dark state: Variable shade 9-13 • Shade control: external, variable • Power on/off: fully automatic • Sensitivity control: low-high, by dial • UV/IR protection: DIN16 • Solar powered (with 1 non-replaceable Lithium battery) • Switch. time: 1/5000s (light to dark) • Dark to light: 0.25 - 0.45s Auto • Low amperage: 10 amps • Grinding function: yes • Operating temp: -5ºC~+55ºC • Storing temp: -20ºC~+70ºC Code no: Barcode: EWHEL0021 6003398094662

Replacement Lenses

• Auto darkening lens is ANSI approved • Cartridge size: 110 x 90 x 9mm • Arc sensor: 2 • Light state: DIN 4 • Dark state: variable shade, 9-13 • Shade control: external, variable • Includes replacement cover lenses • Features auto-off circuitry at 15-20min & low battery indicator • Power on/off: fully automatic • UV/IR protection: DIN16 • Power supply: solar cell • Battery powered with solar assist ± 5000hrs • Switching time: 1/25000s (light to dark) • Dark to light: 0.1-1.0S by control dial • Low amperage TIG: ≥5A(DC), ≥5A(AC) • Grinding function: yes • Low volume alarm: yes • ADF self check: yes • Operating temp: -5ºC~ +55ºC Code no: Barcode: • Storing temp: -20ºC~+70ºC EWHEL0007 6003398066881

Replacement Lenses • INNER CLEAR LENS 021 • OUTER CLEAR LENS 021

Ideal for MIG , STICK & TIG welding and grinding

Page 20

6003398109809 6003398109816

FULLY ADJUSTABLE

• Auto darkening lens is ANSI approved • Viewing area: 90 x 35mm • Cartridge size: 110 x 90 x 5mm • Arc sensor: 2 • Light state: DIN 4 • Dark state: Fixed shade 10/11 • Shade control: fixed shade 10/11 • Power on/off: fully automatic • Sensitivity control: Unadjustable, auto • UV/IR protection: DIN16 • Power supply: solar cells • No battery change required • Switching time: 1/5 000s (light to dark) • Dark to light: 0.25 - 0.45s auto • Low amperage TIG: >35A(DC) • Operating temp: -5ºC~+55ºC • Storing temp: -20ºC~+70ºC

6003398109823 6003398109830

EWLENS019 EWLENS020

Ideal for MIG , STICK & TIG welding and grinding

NON ADJUSTABLE

EWLENS021 EWLENS022

Code no: Barcode: EWHEL0020 6003398094655

Replacement Lenses

Ideal for MIG , STICK & TIG welding

EWLENS011B 6003398109847 EWLENS013 6003398075159 EWLENS012 6003398075142

• Auto darkening lens is ANSI approved • Viewing area: 90 x 35mm • Cartridge size: 110 x 90 x 10mm • Arc sensor: 2 • Light state: DIN 4 • Dark state: Variable shade 9-13 • Shade control: external, variable • Power on/off: fully automatic • Sensitivity control: non adjustable • UV/IR protection: DIN16 • Solar powered (with 1 non-replaceable Lithium battery) • Switch. time: 1/5000s (light to dark) • Dark to light: 0.25 - 0.45s Auto • Low amperage: 20 amps • Grinding function: yes • Operating temp: -5ºC~+55ºC • Storing temp: -20ºC~+70ºC

EWLENS016 EWLENS017 EWLENS015

6003398075180 6003398075197 6003398075173

• INNER CLEAR LENS 007 • OUTER CLEAR LENS 007 • AUTO DARKENING FILTER LENS 007

Ideal for MIG , STICK & TIG welding and grinding

WELDING Skull Cap

Solar Helmet Head Gear

• For protection of the head and neck during welding

• Fits standard welding helmet

Code no: Barcode: EWHEL0004 6003398077153

Code no: Barcode: EWLENS018 6003398075203

Sold Individually

Auto Goggles • Auto darkening lens is ANSI Z87.1 Approved • Fixed shade of DIN 10/11 & clear state shade DIN 3 • Lens darkening reaction time is 0.5ms Code no: Barcode: TOOW4263 6003398055533

Ideal for robotic & automated welding, inspectors, visitors, etc.

Goggles • Ideal for Gas welding Code no: Barcode: TOOW4243 6003751006974

Sold Individually

Flip Front Face Shield • Standard welding helmet • Adjustable headgear • Lens size 108 x 51mm Code no: Barcode: TOOW4242 6003751009067

Sold individually

Pre-Packs

Sold individually

• Ideal for grinding, inspectors, forman, visitors, etc.

Code no: Barcode: TOOG727A 6003751002488

Sold individually

Code no:

Description:

Barcode:

TOOW4242G TOOW4242A TOOW4242H TOOW4242B

SHADED FOR FLIP FRONT SHADED FOR FLIP FRONT CLEAR FOR FLIP FRONT CLEAR FOR FLIP FRONT

6003398074084 6003751012166 6003398074091 6003751012173

CHROME LEATHER GLOVES

CHROME LEATHER GLOVES

• 8” • Elbow

• 2.5” • Wrist

Code no: Barcode: TOOG725B 6003751007971

Code no: Barcode: TOOG725C 6003751014795

Sold per pair

Sold per pair

CHROME LEATHER GLOVES

Workers’ Glove

• 2.5” • Wrist • Green lined

• Candy Stripe • Wrist

Code no: Barcode: TOOG725D 6003751014856

Code no: Barcode: TOOG725A 6003751012401

Sold per pair

Sold per pair

Riggers’ Glove

Leather Glove

• Candy Stripe • Wrist • Heavy duty

• Tig welding • Wrist

Code no: Barcode: TOOG733 6003751339133

Code no: Barcode: TOOG755 6003751348098

Sold per pair

1/pack 5/pack 1/pack 5/pack

Sold per pair

Page 21

GOGGLES / FACE SHIELDS & GLOVES

Safety Goggles - Clear

WELDING Electrode Holder KD 300 Amp

Electrode Holder KD 500 Amp

Code no: Barcode: TOOW4239 6003751014719

Code no: Barcode: TOOW4240 6003751002105

Sold individually

Electrode Holder 300 Amp

Electrode Holder 400 Amp

Electrode Holder 600 Amp

• Heavy Duty • Industrial • Collet Type – (Optimus)

• Heavy Duty • Industrial • Collet Type – (Optimus)

• Heavy Duty • Industrial • Collet Type – (Optimus)

Code no: Barcode: EWC0072 6003398060384

Code no: Barcode: EWC0073 6003398060391

Code no: Barcode: EWC0074 6003398060407

Sold individually

Sold individually

Sold individually

ELECTRODE HOLDERS & EARTH CLAMPS

Sold individually

Arc Earth Clamp 300 Amp Crocodile style

Arc Earth Clamp 500 Amp Crocodile style

Code no: Barcode: TOOW4238 6003751014702

Code no: Barcode: TOOW4241 6003751343185

Sold individually

G - Type Brass Earth Clamp 500 Amp • Heavy Duty

Code no: Barcode: EWC0064 6003398060315

Sold individually

Page 22

Sold individually

WELDING • Rated at 200 Amps • Used on cables with an area of 10mm2 to 25mm2 • Used on welding cables to fit on most welding machines

2 per

QUALITY

Welding Accessories

pack

Code no: Barcode: EWPACA001 6003398058855

Pre-Pack Jack Plugs 35-50mm Welding Accessories

2 per

QUALITY

Welding Accessories

pack

• Dinse Connectors • Rated at 200 Amps • Used on welding machines to connect welding cables.

Code no: Barcode: EWPACA003 6003398058879

Sold 2 per pack

QUALITY

• Rated at 350 Amps • Used on cables with an area of JACK PLUG 35mm2 to 50mm2 DINSE MALE 2 35-50MM pack

Sold 2 per pack

Jack Plugs 50-70mm

Code no: Barcode: EWC0053 6003398060209

Sold individually

Pre-Pack Machine Sockets 35-50mm

Female Cable Connector 35-50mm

QUALITY

Welding Accessories

• Dinse Connectors • Rated at 350 Amps 2 per

pack

EWC0059 6003398060261 Code no: Barcode: EWPACA004 6003398058886

Sold Individually

Sold 2 per pack

EWC0061 6003398060285 Code no: Barcode: EWC0054 6003398060216

Sold Individually

Dinse Connector DIGITEC 10-25mm

Female Cable Connector 50-70mm

Code no: Barcode: EWC0055 6003398060223

Sold individually

Sold individually

Bar Connector Black

• For ARC 500/600 EWM0013-I & EWM0014-I

• For MCOW4226 Digitec 200

• For ARC 500/600 EWM0013-I & EWM0014-I

Code no: Barcode: EWC0049 6003398060179

Sold individually

• Rated at 500 Amps • Used on cables with an area of 50mm2 to 70mm2 • Used to connect welding cables together

Code no: Barcode: EWC0056 6003398060230

Bar Connector red

Code no: Barcode: EWC0051 6003398075999

Sold individually

• Rated at 500Amps • Used on welding machines to connect welding cables.

• Rated at 500 Amps • Used on cables with an area of 50mm2 to 70mm2 • Used on welding cables to fit on most welding machines

Sold individually

• Connectors • Rated at 350 Amps • Used on cables with an area of 35mm2 to 50mm2 • Used to connect welding cables together

JACK PLUG DINSE MALE 35-50MM

Machine Sockets 50-70mm

Code no: Barcode: EWC0057 6003398060247

• Connectors • Rated at 200 Amps • Used on cables with an area of 10mm2 to 25mm2 • Used to connect welding cables together

Sold 2 per pack

per

Code no: Barcode: EWPACA002 6003398058862

Female Cable Connector 10-25mm

Pre-Pack Machine Sockets 10-25mm

Code no: Barcode: EWC0050 6003398060186

Sold individually

Sold individually

Welding Cables

• 16mm2 area 60% duty cycle at 105 Amps

• 25mm2 area 60% duty cycle at 135 Amps

• 35mm2 area 60% duty cycle at 180 Amps

• 50mm2 area 60% duty cycle at 295 Amps

Code no: Barcode: EWCAB1161 6003398067215

Code no:

Barcode:

Code no:

Barcode:

Code no:

Barcode:

EWCAB1162

6003398067222

EWCAB1163

6003398067239

EWCAB1164

6003398067246

Sold per meter

Pre-Pack Cable Lug 16-10mm

Pre-Pack Cable Lug 25-10mm

4 per

4 per

pack

Code no: Barcode: EWPPLUG0001 6003398070475

Sold in Packs of 4

Pre-Pack Cable Lug 35-10mm 4 per

pack

Code no: Barcode: EWPPLUG0002 6003398070482

Sold in Packs of 4

pack

Code no: Barcode: EWPPLUG0015 6003398070499

Sold in Packs of 4

Page 23

WELDING CONSUMABLES

Pre-Pack Jack Plugs 10-25mm

WELDING 5 Row Wire Brush

Coarse Block Brush

• Mild Steel

Code no: Barcode: TOOB38 6003751003997

Code no: Barcode: TOOB39 6003751016911

Sold Individually

Sold Individually

4 Row Wire Brush

Sword Brush With Scraper- Plastic Handle

• Mild Steel

• 4 x 16

Code no: Barcode: TOOB37A 6003751002242

Code no: Barcode: TOOB40 6003751030696

Sold Individually

Chipping Hammer

Kwikweld Transformer Oil 1L

• Spring Steel Handle

• For oil cooled welders

Code no: Barcode: TOOH837 6003751006981

Code no: Barcode: TOOO1284 6003751004192

Sold Individually

Sold Individually

Pre-Pack Welding Clamp Magnet

Pre-Pack Welding Clamp Magnet

Pre-Pack Welding Clamp Magnet

• Small • 72mm

• Medium • 92mm

• Xtra-Large • 110mm

Code no: Barcode: TOOW4235 6003751003256

Code no: Barcode: TOOW4234 6003751009654

Code no: Barcode: TOOW4233 6003751017253

Sold Individually

Sold Individually

Sold Individually

Earth & Electrode Welding Cable Set

ARC Welding Kit - 6 Pc Semi Industrial WELDING

KIT 6 PIECE SEMI INDUSTR IAL MMA

TOOW4237A

WELDING

WIRE BRUSHES / CHIPPING HAMMER / MAGNETS / SETS

Sold Individually

SEMI INDUSTRIAL

INCLUDES: • Flip front face shield • 2.5m x 16mm Green welding cable with earth clamp • 2.5m x 16mm Green cable with electrode welding holder • 5 Row wire brush • Metal chipping hammer • Pair of welding gloves

WARNING!

Trade Brands

SA

Using welding machines and and keep machinery plasma cutters can be dangerous. away from children. times. Select Always the correct machine Wear protective gear in work take care, and accessories area at all for the job.

www.lgtools.co.za Made in China

Code no: Barcode: TOOW4237A 6003751001245

Contents • Flip front face shield • 2.5m x 16mm green welding cable with earth clamp • 2.5m x 16mm green welding cable with electrode holder • 5 Row wire brush • Metal chipping hammer • Pair of welding gloves

Sold Individually

Earth & Electrode Welding Cable Set

– Jack Plug FITTING 10-25 (BLUE) • 1 x 300 amp Electrode holder • 1 x 300 amp Earth clamp • 2 x Jack plug 10-25 dinse type connectors • 2 x 1.5m, 25mm2 Blue welding cable Code no: Barcode: EWCAB1070 6003398061473

Ideal for inverter type welding machines

Page 24

Earth & Electrode Welding Cable Set

180AMP – JACK PLUG FITTING 10-25 (GREEN) • 1 x 300 amp Electrode holder • 1 x 300 amp Earth clamp • 2 x Jack plug 10-25 dinse type connectors • 2 x 1.5m, 16mm2 Green welding cable Code no: Barcode: EW-10066 6003751364920

Ideal for inverter type welding machines

• 1 x 300 amp Electrode holder • 1 x 120 amp Booster clamp • 1 x 2.5m welding cable

Code no: Barcode: TOOW4237C* 6003751014665

Ideal for transformer/ oil type welding machines

Earth & Electrode Welding Cable Set H/D

(OIL COOLED MACHINES) – LUG FITTING • 1 x 300 amp Electrode holder • 1 x 300 amp Earth clamp • 2 x 16 x 10mm Lug type connectors • 2 x 2.5m, 25mm2 Blue welding cable Code no: Barcode: TOOW4332 6003751026804

Ideal for transformer/ oil type welding machines

WELDING VYTEC 6013 Mild Steel Electrodes

Code no:

Description:

Barcode:

EW00900 EW00901

2.5MM X 5KG 3.2MM X 5KG

6003398079164 6003398079164

Sold by 5KG Box

E6013 – Mild Steel Welding Rod

E6

01

3

E6

3

01

3

E6

2.0mm

2.5mm

3.2mm

4.0mm

PART NUMBER BARCODE

EW00716 6003398060957

EW00717 6003398060964

EW00718 6003398060971

EW00719 6003398060988

LENGTH AMPS

300 mm 50 - 80

350 mm 60 - 100 mm

350 mm 100 - 140 mm

350 mm 150 - 210 mm

PART NUMBER BARCODE

EW00700 6003398060766

EW00701 6003398060773

EW00702 6003398060780

EW00703 6003398060797

LENGTH AMPS

300 mm 50 - 80

350 mm 60 - 100

350 mm 100 - 140

350 mm 150 - 210

MODEL

2.5mm

3.2mm

4.0mm

PART NUMBER BARCODE

EW00705 6003398060803

EW00706 6003398060834

EW00707 6003398060841

LENGTH AMPS

400 mm 70-110

400 mm 100-140

400 mm 140-180

Tradeweld E7018-1 is an all position low hydrogen electrode designed for high quality, high speed welding on a wide range of carbon & alloy steels requiring radiographic examination. Metal transfer is of smooth spray type with stable arc.

MODEL

2.5mm

3.2mm

PART NUMBER BARCODE

EW00753 6003398061220

LENGTH AMPS

400 mm 45-85

MODEL

2.5mm

PART NUMBER BARCODE

EW00751 6003398061206

LENGTH AMPS

400 mm 45-85

Sold in 1kg boxes

01

E6

01

3

Sold in 5kg boxes

E7018-1 Low Hydrogen Welding Rod E7

01

8-1

E7

01

8-1

Tradeweld E6013 is a smooth running, all positional (including vertical down) rutile type electrode featuring low spatter loss & high operator appeal.

Its superiority in general shop welding & structural work, & its ability to weld on rusty plate surfaces makes it the ideal choice for general purpose welding.

Slag is quick freezing & easily detached from fillet and butt welds & in many cases, is self lifting. The appearance of the weld is excellent.

MODEL

Sold in 4kg boxes

E308L-16 Stainless Steel Welding Rod E3

08

L-1

6

E3

08

L-1

6

Tradeweld E308L-16 is a rutile basic all position stainless steel electrode for 19CR 10Ni type steels as well as 201, 202, 301, 302, EW00750 304L & 308 excellent corrosion resistance in oxidising environments 6003398061190 such as nitric acid, smooth bead appearance & easy slag release as well as corrosion resisting than CHM-308, CHG308.

400 mm 70-120

E309L-16 Stainless Steel Welding Rod E3

09

L-1

E3

6

09

L-1

6

Tradeweld 309L-16 is a rutile basic high CrNi alloyed buffer electrode for welding stainless steel to mild steel as well as root passes in clad EW00752 steel. Excellent weldability and slag release. Weldable on AC & DC and 6003398061213 with high resistance to embrittlement & buffer layer for hardfacing applications.

3.2mm

400 mm 70-120

Sold in 5kg boxes

E312L-16 Stainless Steel Welding Rod E3

12

-16

E3

12

-16

A rutile coated stainless electrode. Easy to weld in all positions (except vertical down). The highly PART NUMBER EW00726 EW00727 EW00728 alloyed electrode is extremely resistant to hot BARCODE 6003398061053 6003398061060 6003398061077 cracking even when diluted with carbon, austenitic & high alloys of steel. Weld deposits give excellent LENGTH 400 mm 400 mm 400 mm resistance to corrosion and oxidation & good scaling AMPS 40-80 75-110 110-150 resistance up to 1000˚C (1850˚F). Recommended for the repair & maintenance of all steels, particularly those of unknown compositions, joining dissimilar steels such as stainless steel to carbon steels and repairing Die’s & Tool steels. Use a buffer layer prior to hard surfacing.

MODEL

2.5mm

3.2mm

4.0mm

Sold in 5kg boxes

E316L-16 Stainless Steel Welding Rod E3

16

E3

L-1

16

6

L-1

6

A low carbon rutile steel electrode. Easy to weld in all positions (except vertical down).

PART NUMBER EW00723 EW00724 EW00725 The smooth arc transfer characteristics leaves low BARCODE 6003398061022 6003398061039 6003398061046 spatter levels, excellent bead shape & good slag removal. Applications for Tradeweld E316L-16 LENGTH 300 mm 350 mm 400 mm include the single & multi-pass welding of matching AMPS 60-80 90-110 110-150 molybdenum content bearing stainless steel such as 301, 302, 303, 304, and 304L types. The 2.5% molybdenum content gives an increased resistance to pitting, corrosion & raises the creep strength for higher temperatures applications.

MODEL

2.0mm (4kg)

2.5mm (5kg)

3.2mm (5kg)

Sold in 5kg boxes

Page 25

WELDING ELECTRODES

Sold in 5kg boxes

WELDING A basic, graphite coated nickel/iron electrode for high strength repair & maintenance welding of spherical PART NUMBER EW00710 EW00711 EW00712 graphite (S.G) iron, austenitic cast iron, meehanite & BARCODE 6003398060896 6003398060902 6003398060919 a wide range cast iron. It produces a soft stable arc with minimal penetration & spatter & is very tolerant LENGTH 350 mm 350 mm 350 mm to parent metal condiments such as oil and dirt. The AMPS 50-80 80-110 110-140 ductile nickel/iron weld deposit is readily machinable and has the higher strength required for welding S.G irons. Where higher joint strength is important, Tradecast 60ENiFe-CI may be used for root and fill passes followed by capping passes with Tradecast 100 for smoother surface finish.

Nickel Cast 60 Cast Iron 55%

MODEL

60

EN iFe 60 -CI EN iFe -CI

2.5mm

3.2mm

4.0mm

Sold in 1kg boxes

A basic, graphite coated electrode for the repair & maintenance of a wide range of cast iron PART NUMBER EW00713 EW00714 EW00715 components. It produces a soft stable arc with BARCODE 6003398060926 6003398060933 6003398060940 minimal penetration & splatter. It is very tolerant to parent metal contaminants such as oil and dirt.

LENGTH 350 mm 350 mm 350 mm The ductile Nickel based weld deposit is readily AMPS 60-90 90-110 120-150 machinable with good colour match to most cast irons. Applications of the Tradecast 99 include the repair and reclamation of engine blocks cylinder heads differential housings, gear boxes, pump & machine housings & pulleys etc. in some applications Tradecast 99 has a good “wetting” action due to the high nickel weld deposit.

Nickel Cast 99 Cast Iron 99%

MODEL

99 EN iFe 99 -CI EN iFe -CI

2.5mm

3.2mm

4.0mm

Sold in 1kg boxes

Pre-packed Electrodes Smooth running, all positional (including vertical down) rutile type electrode featuring low spatter loss & high operator appeal. Superior in general shop welding & structural work, & able to weld on rusty plate surfaces. Ideal choice for general purpose welding. Slag is quick freezing & easily detached from fillet and butt welds & in many cases, is self lifting. The appearance of the weld is excellent.

6013 2.0MM

12 per

6013 2.5MM

10 per

EWPACELE001 6003398059050 EWPACELE002 6003398059067

6013 3.2MM

EWPACELE003 6003398059074

All position low hydrogen electrode designed for high quality, high speed welding on a wide range of carbon & alloy steels requiring radiographic examination. Metal transfer is of smooth spray type with stable arc.

pack pack

7018-1 2.5MM

8 per

pack

EWPACELE010 6003398059098

8 per

A rutile coated stainless electrode. Weld in all positions (except vertical down). Highly alloyed electrode extremely resistant to hot cracking even when diluted with carbon, austenitic & high alloys of steel. Weld deposits give excellent resistance to corrosion and oxidation & good scaling resistance up to 1000˚C (1850˚F). Recommended for the repair & maintenance of all steels, particularly unknown compositions, joining dissimilar steels such as stainless steel to carbon steels and repairing Die’s & Tool steels. Use a buffer layer prior to hard surfacing.

8 per

312 2.5MM

EWPACELE035 6003398059203

312 3.2MM

EWPACELE036 6003398059210

pack

A low carbon rutile steel electrode. Weld in all positions (except vertical down). Smooth arc transfer leaves low spatter levels, excellent bead shape & good slag removal.

Applications: single & multi-pass welding of matching molybdenum content bearing stainless steel such as 301, 302, 303, 304, and 304L types. The 2.5% molybdenum content has increased resistance to pitting, corrosion & raises the creep strength for higher temperatures applications.

pack

316L-16 2.0MM

6 per

316L-16 2.5MM

pack

EWPACELE040 6003398059234

pack

WELDING ELECTRODES

Pre-packed Electrodes Basic, graphite coated nickel/iron electrode for high strength repair & maintenance welding of spherical graphite (S.G) iron, austenitic cast iron, meehanite & a wide range cast iron. Produces a soft stable arc with minimal penetration & spatter & is very tolerant to parent metal condiments such as oil and dirt. The ductile nickel/iron weld deposit is readily machinable & has higher strength required for welding S.G irons. Where higher joint strength is important it be used for root & fill passes followed by capping passes with Tradecast 100 for smoother surface finish.

EWPACELE045 6003398059272

6 per

pack

GOUGE 3.2MM

6 per

EWPACELE056 pack 6003398059326

CAST IRON 55% 2.5MM EWPACELE060

CAST IRON 55% 3.2MM EWPACELE061

Suitable for Arc welding

TRADEweld offers a comprehensive range of welding electrodes for most applications.

E-mail: sales@lgtools.co.za Tel: 031 717 6800 www.lgtools.co.za Or order on RapidTrade Page 26

6003398059340 6003398059357

6 per

pack

6 per

pack

pack

EWPACELE041 6003398059241 8 per

Suitable for Arc welding

HF 55 3.2MM

10 per

ALUMINIUM ARC 2.5MM TOOW4291 6003751031563

4 per

pack

WELDING Mild Steel TIG Wire (5kg)

Stainless Steel 308 TIG Wire

• Suitable for single-pass and multi-pass welding for structures fabricated by carbon steel and 500MPa grade low alloy steel, such as vehicles, bridges, construction and mechanical structures

• Used to weld 302, 304L wrought & cast form stainless steel • Excellent for joining similar austenitic stainless steel

Code no:

Desc.:

Barcode:

Code no:

Desc.:

Barcode:

EWMG00028 EWMG00029 EWMG00030

ER70S-6 1.6MM ER70S-6 2.4MM ER70S-6 3.2MM

6003398074657 6003398074664 6003398074671

EWSW00030 EWSW00032

ER308 1.6MM ER308 3.2MM

6003398061329 6003398061343

Sold in 5kg Tubes

Sold in 5kg Tubes

Aluminium TIG Wire (5KG)

Stainless Steel 316 TIG Wire

• 5% Silicon, softer than 5356 • It is a general purpose filler alloy • Less sensitive to cracking and produces a shiny clean weld • Excellent for joining cast to wrought form alloys

Code no:

Desc.:

Barcode:

EWSW00025 EWSW00026 EWSW00027

ER316 1.6MM ER316 2.4MM ER316 3.2MM

6003398061299 6003398061305 6003398061312

Sold in 5kg Tubes

Code no:

Desc.:

Barcode:

EWMG00022 EWMG00023 EWMG00024

4043 1.6MM 4043 2.4MM 4043 3.2MM

6003398074596 6003398074602 6003398074619

• 5% Magnesium, it has a high shear strength, corrosion and crack resistance • Used to weld/repair injection moulds and in the marine environment Code no:

Desc.:

Barcode:

EWMG00025 EWMG00026 EWMG00027

5356 1.6MM 5356 2.4MM 5356 3.2MM

6003398074626 6003398074633 6003398074640

Sold in 5kg Tubes

TIG WIRE

• Used for low impact toughness & high strength and welds that need a low ferrite.

• Used to weld stainless 316L together & has excellent anti corrosion property’s

Page 27

WELDING Mild Steel MIG Wire 15kg

Mild Steel MIG Wire 5kg • A general purpose mild steel welding wire • Suitable for single-pass and multi-pass welding for structures fabricated by carbon steel and 500MPa grade low alloy steel such as vehicles, bridges, construction and mechanical structures

• A general purpose mild steel welding wire • Suitable for single-pass and multi-pass welding for structures fabricated by carbon steel and 500MPa grade low alloy steel such as vehicles, bridges, construction and mechanical structures

Code no:

Desc.:

Barcode:

Code no:

Desc.:

Barcode:

EWMG00006 EWMG00002A EWMG00003B

ER70S-6 0.8MM ER70S-6 0.9MM ER70S-6 1.0MM

6003398053973 6003398055717 6003398054178

EWMG00001 EWMG00002 EWMG00003 EWMG00004

ER70S-6 0.8MM ER70S-6 0.9MM ER70S-6 1.0MM ER70S-6 1.2MM

6003398055694 6003398055700 6003398055724 6003398055755

Sold Individually in 5kg Spools

Sold Individually in 15kg Spools

Mild Steel Flux Cored MIG Wire 5kg

Mild Steel Flux Cored (Gas Assisted) MIG Wire 15kg • A general purpose gasless mild steel welding wire • Ideal for welding on site, non cosmetic finish

• A flux cored gas assisted mild steel welding wire • Suitable for welding medium and thick plates fabricated by mild steel and 490Mpa high strength steel • Popularly used in flat and horizontal and fillet welds of vessels, machines and bridges

Code no:

Desc.:

Barcode:

Code no:

Desc.:

Barcode:

EWSW00006

GASLESS FLUX CORED 0.9MM

6003398053959

EWMG00008 EWMG00009

ER 71-T1 1.2MM ER 71 T1 1.6MM

6003398055793 6003398055809

Sold Individually in 5kg Spools

Sold Individually in 15kg Spools

Stainless Steel 308L MIG Wire 15kg

Stainless Steel 309L MIG Wire 15kg

MIG WIRE

• Used to weld 302, 304L wrought & cast form stainless steel • Excellent for joining similar austenitic stainless steel

• Used to weld dissimilar alloys like mild to stainless steel • Excellent toughness and high strength

Code no:

Desc.::

Barcode:

Code no:

Desc.:

Barcode:

EWMG00017 EWMG00010

ER308L 1.0MM ER308L 1.2MM

6003398055885 6003398055816

EWMG00019 EWMG00011

ER309L 1.0MM ER309L 1.2MM

6003398055908 6003398055823

Sold Individually in 15kg Spools

Sold Individually in 15kg Spools

Stainless Steel 316L MIG Wire 15kg

Aluminium MIG Wire For Spool Gun 500g ALUMINIUM MIG WIRE 4043 0.8MM

• Used for low impact toughness & high strength and welds that need a low ferrite.

• Used to weld stainless 316L together & has excellent anti corrosion property’s

• 5% Silicon, softer than 5356 it is a general purpose filler alloy • Less sensitive to cracking & produces a shiny clean weld • Excellent for joining cast to wrought form alloys ALUMINIUM MIG WIRE 5356 0.8MM

• 5% Magnesium, it has a high shear strength, corrosion & crack resistance • Used to weld/ repair injection moulds and in the marine environment

Code no:

Desc.:

Barcode:

Code no:

EWMG00018 EWMG00015

ER316L 1.0MM ER316L 1.2MM

6003398055892 6003398055861

EWMG00020 ALUMINIUM MIG WIRE 4043 0.8MM EWMG00021 ALUMINIUM MIG WIRE 5356 0.8MM

Sold Individually in 15kg Spools

Page 28

Desc.:

Sold Individually in 500g Spools

Barcode: 6003398068786 6003398073407