413 owners manual

Tow-Type 0222413 CVR

4/25/05

11:15 AM

Page 1

Operations / Instruction / Parts

113 / 213 / 313 / 413

TOW-TYPE PAVERS

Printed in U.S.A.

BOMAG Paving Products 618 N. Enterprise Dr. Warrensburg, MO 64093

Catalog Number

0222413

5/05

Table of Contents Introduction General Safety Instructions Assembly Units Paver Set Up and Operation Cleaning / Wash Down ProPaver General Maintenance Operators Station Power Unit Pullbox Hopper Assembly Screed Assembly Electrical Hydraulic System Blank Page Kohler Engine Manual Honda Engine Manual Robin Engine Manual Warranty Statement

2 3-5 6-7 8-10 11 12 13-18 19-23 24-39 40-48 49-50 51-53 54 55-70 71-126 127-158 Inside Back Cover

1

WARNING: Do not attempt to operate the Paving Machine before thoroughly reading, comprehending, and following the instructions in the operator's manual. Serious injury or death may occur!

This tow type paver was carefully designed and manufactured to provide the utmost in dependable service. To obtain the best results and keep it operating efficiently, read and follow the instructions in the operator's manual.

This safety alert symbol identifies important safety messages in this manual.

When you see this symbol, be alert to the possibility of personal injury and carefully read the message that follows.

This new machine has been factory tested, lubricated, and initial settings and adjustments carefully made. However, it is recommended that a thorough inspection of the entire machine be made prior to starting , to correct ant problems which may have occurred during transit.

The information contained in the Operator's Manual should enable experienced paving personnel to operate and maintain this unit. The sequence and detail of operating and servicing instructions are presented to assist an adequately trained equipment operator in performing paving and maintenance tasks.

The specifications, descriptive information, operating, and servicing instructions contained in this manual were adequate and accurate at the time of approval for printing. Improvement of the product is a constant goal at BOMAG Paving Products, so we reserve the right to make changes at any timewithout notice and without incurring any obligation. BOMAG Paving Products is vitally interested in yoursatisfaction and we are anxious to help you with all of your maintenance and service needs.

Record the serial number of both the paver and engine in the space provided below. Your dealer needs this information to give you prompt, efficient service when you order parts or optional equipment.

Paver Model Number________________Serial Number________________ Engine Make______________Model___________Serial Number Optional Equipment

Date 2

General Safety Instructions One of the primary considerations in designing and manufacturing this ProPaver by BOMAG was to make the machine and the operation of same as safe as possible. Shielding, simple adjustments and other safety features were built into the Paver wherever possible.

All machinery should be operated and serviced only by responsible persons who have been properly instructed and delegated to do so. Read and thoroughly understand all instructions contained in this manual, the engine manual, and all optional equipment manuals before attempting to operate or service the paver.

1) Only the operators should be allowed on the operator's platform when the paver is in operation.

2) be

Clothing worn by all persons working close to the paver should fairly tight and belted. Loose jackets, shirts or pants should never be worn because of the danger of getting caught in moving parts.

3) Be sure all shields and guards are in place and in good condition before starting the machine.

4)

Always mount and dismount the paver from the rear, using the walkway, steps and handrails provided. Never dismount paver to the side, or forward.

5) Assure that all hands and feet are clear of moving parts before starting paver.

6) Make sure everyone is clear of the paver before starting so they cannot be struck by or caught in moving parts.

7) ing

Never attempt to tow or move the ProPaver before first engagthe tow hitch arms, the machine could possibly overturn.

8) to

Keep the operator's platform clean, Do not use it as a place carry loose tools, lunch boxes, etc.

9) Refuel the paver only when the engine has been shut off. Do not permit sparks, open flames or smoking within 50 feet of paver when refueling. Never refuel paver with screed heaters lit and operating.

10) or

Never allow horseplay near the paver when it is in operation being serviced.

Safety is no accident - Take time to be safe!!!!

3

Escaping hydraulic fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before disconnecting any hydraulic lines, be sure to relieve all pressure. Before applying pressure to a system , be sure all connections are tight and that all lines, tubes, and hoses are not damaged. Fluid escaping from a very small hole can be almost invisible. Use a piece of cardboard or wood, rather than hands, to search for suspected leaks.

11)

If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.

12)

Always be sure that all control switches are in the "OFF", "Pause", or "Neutral" position, hopper wings and screed are lowered and the engine is shut off before leaving the operator's station.

13)

Never use the wash down system when the screed heaters are lit or operating.

14)

Never clean, lubricate, or service the paver when it is running.

15)

Do not open propane valves to the screed burners unless flame is present to light the burners. An accumulation of unburned gas could result in explosion. Do not allow smoking when lighting propane fired screed burners.

16)

Do not allow smoking or the use of open flame when checking the electrolyte level in the battery. An explosion could result.

If skin or eyes are exposed flush immediately with water and see a doctor.

Safety suggestions for persons working in the area of an operating paver 1)

When working in the vicinity of the machine, stand in full view of the operator; but never in front of the machine when the machine is operating. Stay clear of hopper, side arms, and screed when machine is operating. Do not walk in front of the hopper or extended screed, or stand at the end of the screed if the hydraulic screed extensions are being used.

2)

If necessary to remove spillage from the roadway, have the operator stop the machine first. Working close to a moving machine is dangerous Accidents don't just happen- they are caused!

Take time to be safe!!!

4

3)

Do not remove paving material from the hopper or auger trough while the paver is operating. The operator should be advised when adjustments are being made.

4)

Do not attempt service or repairs you do not understand or cannot perform competently.

5)

Never go between the tuck and the paver.

6)

Do not attempt to clean , lubricate or service the paver while it is running.

7)

If any safety related defects are discovered, inform the operator to shut the machine down and correct the defect.

Pick up and transportation procedure

When you receive your new ProPaver, you should establish the proper pick up procedure for your truck. The proper chain link to maintain a level and stable condition should be located and marked permanently with paint or wire. If the truck used to transport the Propaver is a short bed vehicle, a small winch should be mounted to the frame of the truck to secure the bed in the horizontal position.

BOMAG Paving Products, does not recommend transporting the ProPaver for long distances while attached to your dump truck. A maximum speed of 35 miles per hour is recommended.

A trailer is recommended for this function. The transportation of the ProPaver for short distances is described in the above paragraph.

Safety doesn't cost - It saves!

Take time to be safe!!!

5

Assembly Units POWER UNIT GROUP The Power unit group consists of a heavy-duty 20-horse power engine that is coupled to a triple gear pump. The pump nearest to the engine is an eight-gallon per minute pump, and drives all hydraulic cylinder functions (gates, wings, screed extensions, screed lift and hitch arms.)

The next two pumps drive the left and right augers. four gallon per minute pumps each.

These are

If your paver has the electric over hydraulic backup option, this is a four-gallon per minute pump driven by an electric DC motor. This pump will drive all cylinder functions. This pump cannot drive the auger drive functions. This backup system may be used by actuating the ignition key switch counter clockwise, to the electric hydraulic position on the ignition switch.

All BOMAG Paving Products tow type asphalt pavers are equipped with manual hand pumps. These pumps are capable of driving all cylinder functions of the machine. The appropriate valve must be actuated, for the function you are attempting during the stroking motion of the pump.

HOPPER ASSEMBLY The hopper on the ProPaver by BOMAG tow type pavers is eight feet wide with a wing on each side. The wings are hydraulically operated, which allows the operator to raise and lower them with ease. The lowering of the wings eliminates any truck/paver interference and also allows easy access to the asphalt mix from the side of the paver.

This is especially valuable when you need to shovel from the hopper.

WARNING: Never attempt to remove asphalt mix from an operating machine. Instruct the truck driver and the paver operator to cease operation before attempting to remove mix from the hopper.

The hopper gates are hydraulically operated with adequate pressure to close the gates, when the hopper is full of asphalt. The gates may be operated independently or as one by adjusting the valves located on the hopper back, directly above the hydraulic pump cover. The double acting cylinders on the gates permits trouble free metering of material on the open and close operations, and will eliminate excess material clean up at the end of the paved mat.

6

SCREED ASSEMBLY The screed assembly on the BOMAG Paving Products tow type asphalt pavers have a standard paving width of eight feet, and can be hydraulically extended to thirteen feet. This is a very unique screed in so much that the entire mat surface is compacted. The screed extensions are not strike offs, they have compacting wear plates attached to them.

The screed depth controls are attached to the hopper frame by two spherical, self-aligning, cast iron nuts. This is to insure effortless depth adjustment regardless of the paving setting.

The screed assembly may be adjusted to a three-inch crown or a two-inch invert.

Because of the tight machining tolerances of the connecting joints between the screed and the hopper, accuracy of the mat thickness can be accomplished. When an adjustment or setting is made on the depth control screw, a rapid change in mat thickness is accomplished and can be maintained with ease. In most cases, when a desired mat thickness is obtained, little or no compensation will need to be made.

UNDERCARRIAGE The independent mounted boggy assemblies contribute largely to an accurate and successful paving operation. The independent boggies are precisely located, and mounted into the hopper frame. This offers the capabilities to pave at different depths on either sides of the screed assembly, and offers an accurately paved mat.

To change the paving depth from five to ten inches, in lieu of the standard zero to five inch setting, it is necessary to remove and flip the boggy assemblies over, and reinstall them into the support legs.

Two double acting cylinders power the hitch arms that attach to the dump truck to pull the paver. The hitch arms have three position adjustments for the rim rolls and side rolls that will permit attaching to most trucks.

WARNING: Never get betweenthe dump truck and the paver when attempting to engage the two. Serious injury or death could result!!

WARNING: Never attempt to tow the paver before first engageing the hitch arms. Serious injury or death could result!!!

7

Paver set up and operation When the paver is on the job site and before asphalt is dumped in the hopper, the machine should be sprayed with cleaning fluid (with the spray cleaning system furnished) inside the hopper, on the bumper rollers, augers, screed extensions, and under the screed.

Check the screed for crown, valley, or level condition. This is accomplished by checking the indicator for the "0" setting and by sighting the underside of the leading edge of the screed. Adjust the screed to proper position with the ratchet on the center of the screed. Detach chains holding the paver to the truck by raising the truck bed. Start the engine, move the hopper wings and tow hitch arms to the open position.

Connect the tow hitch arms in the rear wheels of the truck.

Excessive pressure should not be applied to the tires; retract the hitch arms only until the side rolls touch the tires of the truck.

To move the paver in position for the first paving pass, put the tailgate hook in the center of the tailgate of the truck and hook the screed lift chain into the tailgate hook. Raise the screed off the ground about four inches.

Before beginning to pave, it is essential that the screed be elevated a distance equal to the desired mat depth plus enough extra height to allow for the mat compaction by rolling. This is done by placing "starting blocking" under the screed. If a finished mat depth of two-inches is desired, starting blocks two and one quarter inch thick would provide a suitable starting height. The starting blocks should be at least as long as the width of the screed wear plate, and placed lengthwise with the direction of travel. Place one block under each end of the screed. If necessary, place additional blocks beneath the screed extensions. This placement will provide the screed wear plate with bearing surfaces that are essentially parallel with the grade. Lower the screed, bringing it to rest upon the starting blocks. With the screed in this position rotate the screed depth cranks until the screed wear plate is completely flat on the starting blocks and free rotary travel (no resistance) of the screed depth cranks is attained. Rotate the screed depth cranks an additional one half turn clockwise. When paving begins, check mat depth and adjust screed depth cranks until desired mat depth is attained. Use the screed depth gauge as a reference point only.

To adjust the ProPaver by BOMAG paving width from the standard eightfeet, simply extend the hydraulic screed extensions to the desiredpaving width. The screed extension controls are located on eachoperator's console.

8

Before beginning to pave with bituminous materials, the screed should be preheated. This helps to prevent the hot mix from sticking to a cold screed plate, and produces a smooth, tight mat surface.

Preheating should be performed if the machine sets a long period of time between loads allowing the screed plate to cool. At the beginning of the day allow 15 minutes for heat up of a cold screed.

Shorter periods of time will be sufficient when the screed is sitting on warm material. When heating the screed, the extensions should be retracted full in to insure proper heating of the extension wear plate.

IMPORTANT: Avoid overheating of the screed which may warp the screed wear plate and frame.

Never refuel paver with screed heaters lit and operating.

Never use the wash down system when the screed heaters are lit or operating.

Do not open propane valves to the screed burners unless flame is present to light the burners. An accumulation of unburned gas could result in explosion. Do not allow smoking when lighting propane fired screed burners. If screed heaters should go out for any reason, never attempt to relight until excess propane is ventilated from the screed burner chamber.

Failure to observe the above could result in fire, personal injury or death!!!

To light the screed heaters, turn the tank. Adjust the pressure valve until the eight psi. Hold an open flame next to the nozzles and open the burner valve. Repeat the opposite burner.

valve on top of the propane gage reads between six and holes in one of the burner the previous steps to light

The ProPaver's screed strike off shoes are located on the end of the screed extensions and may be used in two different ways. When not paving adjacent of previously paved areas, the strike off shoes should be free floating. Loosen the jam nuts on the outer most hex head bolts, and rotate the bolts counter clockwise until the strike off 9

shoe will move easily. bolts.

Retighten the jam nuts to secure the hex head

Loosen the jam nuts on the two vertical five inch long all thread hex head bolts, and rotate the bolts clockwise until maximum vertical movement of the screed strike off shoe is available. Retighten the jam nuts to secure the long hex head bolts. The screed strike off shoes are now full floating, and will maintain a positive edge of the mat at any paving depth.

When paving next to a previously paved area, if a smooth joint is to be made, the screed strike off shoe on the side where the joint is being made should be adjusted so that it is level with the bottom of the screed wear plate and secured. To secure the screed strike off shoe, simply reverse the steps described previously to make the shoe full floating.

Set tailgate chains on truck to desired opening of the tailgate.

Raise the truck bed sufficently to dump into the paver hopper. Engage the augers at this time in the "Automatic" position. Open gates sufficently to allow material to the augers. It is not necessary to open the gates to full open position. The augers are visible from the rear of the machine and a constant check on material in front of the screed can be observed continuously. This will be very helpful when operation of the augers is in the "Manual" position. When the augers are operating in the "Automatic" position, the augers will engage and disengage when the material flow is needed.

Move the paver forward four or five feet and stop at this point.

Check the thickness of the pad. This will allow time for the screed extensions to warm up properly to provide for a smoother mat finish.

When you approach the end of the paving pass, observe the augers and the amount of material in front of the screed. Within a short timr the operator will be able to close the gates, and control the amount of material in front of the screed to match within a few inches of the previous mat. No tailing of the pad and virtually all clean up at the end of the pad is eliminated.

Hook the screed lift chain in the tailgate hook and raise the rear of the paver off the pad. Caution should be taken when approaching the end of the pass to minimize the amount of material in the hopper. This will make it easier to maneuver the machine to the next pass.

If the width of the required pass is less than eight feet, the pull can be lapped over the previous pull. The screed on the lapped side of the paver is to be set on "0" and the screed extension fully retracted. The compaction of the screed should erase any marks in the asphalt mat.

10

Cleaning / Wash Down To ensure proper performance and maximum life of the ProPaver, it must be cleaned and washed down with diesel fuel at the end of each work day while the machine is still warm. Daily clean up of the paver can significantly increase the life of components in the material handling areas and reduce many mat problems. Abrasive materials which accumulate in bearing, auger, and hopper areas can break loose and produce tears in the mat as they pass under the screed. All residual asphalt materials should be removed from the paver, especially in the material handling areas, and the surfaces sprayed to "terminate" any remaining residue. This leaves a petroleum film on surfaces to reduce the potential for material sticking the next time the paver is used.

The clean up and wash down procedure should be performed away from the paving site. The paver should be moved to a designated area and all functions shut off.

WARNING: Diesel fuel is both flammable and slippery, extreme care must be exercised during the clean up and wash down procedure to avoid fire or personal injury.

Never wash down the machine while burners are operating. This could result in fire or explosion!!!

Never smoke or allow other persons who are smoking into the area during wash down. This could result in fire or explosion!!!

Never stand in the hopper or on or around the augers while the paver is operating.

Run the augers only when required to gain access to all surfaces and only after personnel are out of the material handling areas.

There is a wash down hose on the ProPaver, next to the left operator's console. The ON/OFF toggle switch is located on the right console. The wash down switch should be turned on only immediately before wash down is to begin, and off immediately after it is completed.

11

ProPaver General Maintenance The ProPaver tow type paver/finisher is a high quality product designed to provide many years of reliable operation if properly maintained. The following information will aid in proper maintenance.

1) During the first few hours/days of operation with a new machine, check fasteners (bolts, nuts, ect.) on high vibration areas to ensure tightness. Occasionally these will become loose while a machine is starting up. Tighten any loose fasteners you might find. This should not continue after 10 to 20 hours of operation, (hitch arm bolts, hopper wing mounting bolts, ect.).

2) Replace fluids and filters as recommended in the Power Unit Maintenance and Lubrication Points sections.

3) Refer to and follow recommendations in the Wear Check Points section.

4) Check and maintain all fluid levels daily.

5) Clean asphalt residue from hopper, screed augers, and anywhere else it accumulates after each use. (Refer to Cleaning/Wash Down Section) 6) Repair (touch up) paint chips, nicks and worn spots to prevent exposing raw steel to the elements to help prevent rust.

7) Replace any decals that have been damaged, worn, or painted over.

12

Operators Station 4

1 3 2

5 7

7

6

10 Item 1 2 3 4 5 6 7 8 9 10

Qty. 2 1 1 1 1 1 2 2 1 2 1

9 Description Operation Control Valves 400 Gate Control Sight Temperature Gauge Propane Fuel System Engine Throttle Control Panel Hand Pump Auger Controls Screed Crown Adjustment Screed Burners Operators Platform

8 Pg.# 14 14 15 15 15 16 17 17 18 18

13

Operation Control Valves

6

1

Item 1 2* 3 4 5 6 7 8 9 10 11 12

2

3

Qty. 1 1 1 1 1 1 1 1 1 1 1 1

4

5

7

8

9

11

Description Towarm Control / Releases and Engages Towarms Gate Control / Opens and Closes Hopper Gates Wing Control / Extends and Retracts Wings Extension Control / Extends and Retracts Screed Extensions LS Screed Depth Control / Raises and Lowers paving surface LS 400 Gate Control LS / Sets Gates to be used separate or together 400 Gate Control RS / Sets Gates to be used separate or together Screed Lift Control / Raises and Lowers Screed Gate Control / Opens and Closes Hopper Gate Wing Control / Extends and Retracts Wings Extension Control / Extends and Retracts Screed Extensions RS Screed Depth Control / Raises and Lowers paving surface RS

* When Gate Control Knobs are in the out position the gates operate separately When Gate Control Knobs are in the in position the gates operate together

14

10

12

Pg.#

Fuel System / Sight Temp Guage

4

2 3 1

Item 1 2 3 4

Qty. 1 1 1 1

Description Propane Conversion Engine Throttle Sight Temperature Gauge Propane Regulator

Part # 5213020 4150048 3445100 5686050

Pg.#

**Models manufactured in 2002 have this Propane Conversion Kit, Part # 5213040

15

Control Panel Assembly

1

2 8 3 4 5 7

6 Item 1 2 3 4

5 6

7 8

Qty. 1 1 1 2 2 2 2 1 2 1 2 1 1

Description Gauge Cover, Hopper End Amo Meter, 30+/3012V Hourmeter RH Slot Machine Screw #10-32 x 3/4"Lg. #10 Washer, Lock #10-32 Hex Nut Panel Mounted Fuse Holder RH Slot Machine Screw #10-32x1-1/2" Lg. #10-32 Hex Nut #10 Washer, Lock #10 Washer, Flat Sealed Two Way Toggel Switch Ignition Switch

Aux. Pump Solenoid is located behind Control Panel.

16

Part # 9216418 6547413 6547814 7731100 7962034 7561230 6473350 7731105 7561230 7962034 7958034 6860100 6547815

Pg.#

Hand Pump / Auger Control

1 2

3

Item 1 2 3

Qty. 2 1 1

Description HydraulicHandPump Feed /Reverse Switch Automatic/Manual Switch

Part # 3662250 6860105 6861005

Pg.#

17

Screed Crown Adjustment / Screed Burner

1

2

3

Item 1 2 3

18

Qty. 1 1 2

Description Screed Crown Indicator Screed Crown Adjustment Turnbuckle Screed Burner Assembly

Pg.# 45 45 45

Power Unit Assembly 3 2

1

4

Item 1 2 3 4

Qty. 1 1 1 1

Description Propane Fuel System Triple Gear Pump Assembly Flow Divider Assembly Auger Manifold Assembly

Pg.# 20 21 22 23

Robin Power Unit Installed

19

Propane Fuel System

1

2

3

4

Item 1 2 3 4

20

Qty. 1 1 1 1 1

Description Propane Conversion 40# Propane Tank Propane Regulator Kohler Engine Command 20HP Honda Engine GX620

Part # 5213020 5872413 5686050 4272020 4272030

Pg.#

54-70 71-126

Triple Gear Pump 2 1

3

4

5 6

7 8

Item 1 2 3 4 5 6 7 8

Qty. 3 1 1 1 1 1 1 1 1

Description Fitting Hyd. 12HB-12MOR Pump, Triple Gear Fitting Brass EL90 8HB-6MP Fitting Hyd. Adaptor 6MJFO-6MOR Fitting Hyd. EL90 6MFJO-6MOR Fitting Brass Reducer 6MP-4MP Fitting Hyd. Reducer 10MOR-6FOR Coupling 1-7/16" x 5/8" HS Adapter Pump Coupling

Pg.# 3299555 3662413 3328440 3300344 3340344 3422360 3372510 4215110 4006050

21

Flow Divider

1 9

2 3

8

4 5

6

7

Item 1 2 3 4 5 6 7 8 9

22

Qty. 1 1 2 3 1 1 2 1 1

Description Valve Flow Divider Flow Divider Body FTG Hyd. Plug HH-4MOR FTG Hyd. Adpt. 6MJ-6MOR FTG Hyd. EL90 8MJ-6MOR FTG Hyd. Adpt. 8MJ-6MOR Valve Check Valve Relief Internal Adj. Set Valve Check

Part # 3937112 9938400 1366200 3300345 3340440 3300440 3931339 3935370 3931339

Pg.#

Auger Manifold Assembly 3 4 2 5 1 6

7 9

8

10

Item 1

2 3 4 5 6 7 8 9 10

Qty. 6 12 12 2 2 4 2 1 6 4 1 1

Description Plug Packard 2 Wire Male Plug Packard Male Term 14-6 Plug Packard Cable Seal Relief Valve Valve Sol 2 Way N/O 12 VDC Valve # Way 12VDC FTG Hyd. EL 90 6 MJFO-6 MOR FTG Hyd. Adpt. 8MJ-8MOR FTG Hyd. Plug 7mm Expanding Sherx FTG Hyd. EL90 6MJFO-6MOR FTG Hyd. Plug SH-8MOR Valve Body 413 Augers

Part # 6648021 6648131 6648110 3935370 3935335 3935339 3340344 3300415 3362000 3344345 3367415 9105100

Pg.#

23

Pullbox Hopper Group Assemblies 7

5

10

8

1

12

3

11

2 6 9 4

Item 1 2 3 4 5 6 7 8 9 10 11 12

24

Qty. 4 2 2 1 3 2 2 2 1 1 1 2

Description Bumper Roller Assembly Boggie Wheel Assembly Towarm Assembly Screed Lift Bracket Assembly Tailgate Hook Weldment Hopper Wing Assembly Asphalt Splash Guard 413 Hopper Weldment Hydraulic Tank Assembly Diesel Tank Assembly Valve Assembly, 400 Gate Control Screed Screw Assembly

Part # 9258401 9104006 9255205 9136200 9475000 9456001 9980400 9871108 9871113 9150102

Pg.# 25 26-28 29-30 31 32 33 34 35 36 37 38 39

Bumper Roller Assembly

1

2

3

4 5

Item 1

2 3 4 5

Qty. 2 2 2 4 2 2 1

Description Anchoring Pin HHCS 5/16"-18x 1-1/4" Washer Flat 5/16" Bumper Roller Bearing Bumper Roller Assembly Bumper Roller Axle 413 Hopper Weldment

Part # 9636000 7727525 7962254 4070110 9258401 9253962 9980400

Pg.#

Note: Right and Left Sides are assembled identically.

25

Boggie Wheel Assembly Instl.

2 1 3

4 5

6 7 8

Item 1 2 3

7

Qty. 1 1 4 4 4 4 2 4 4 4 2 2 2 2 2 2 2

8

1

4 5

6

26

Description Beetle Weld LH Beetle Weld RH Hex Nut 5/8-11 Bolt 5/8-11x2 Washer Flat 5/8 " Washer Lock 5/8" Axle-Boggie Hex Nut 1/2"-13 self locking Bolt 1/2"-13x3 Washer Lock 1/2" Pin Screed Arm Hookup Pin Anchoring Hex Nut 5/16"-18 Bolt 5/16"-18x1-1/4" Washer Flat 5/16 " Washer Lock 5/16" Boggie Wheel Assembly Pneumatic Tires Hard Tires Hopper Weldment

Part # 9980001 9980000 7561294 7721755 7956294 7962294 9763420 7571278 7721660 7962278 9636003 9636000 7561254 7721525 7956254 7962254 9104008 9104009 9982410

Pg.#

27 28

Boggie Wheel Assembly, Pneumatic

2

1

3 7

6

5 Item 1 2 3 4 5 6 7

Qty. 1 2 8 4 4 4 4 4

4 Description Boggie Weldment Axle Pneumatic Bearing Retainer Hex Jam Nut 1" Pneumatic Wheel Hex Jam Nut 1" Washer Lock Bolt 5/8"-11x1 HHCS

Part # 9104010 9253972 9253908 7566342 4889010/9990031 9955413 7962294 7721749

Pg.#

Note: Right and Left sides are identical.

27

Boggie Wheel Assembly, Hard Tires

2 1

6

5 3 4 Item 1 2 3 4 5 6

Qty. 1 8 4 4 2 4 4

Description Boggie Weldment Washer Flat1-1/4" Solid Tire w/Bearing Collar Shaft 1-1/4" Axle, Solid Wheels Washer Lock Bolt 5/8"-11x1 HHCS

Note: Right and Left sides are identical

28

Part # 9104010 7958374 4889011 4195111 9253961 7962294 7721749

Pg.#

Towarm Assembly 2 3 4

5 6 7

1

8 9 10 11

12

13 14 Item 1 2 3 4

5 6 7 8 9 10 11 12 13 14

Qty. 1 1 1 4 4 4 2 2 2 1 1 1 1 1 1 1 1 1

Description Cotter Key Nut Castle 1"-14 Washer Hardened Bolt 3/8"-16x 1" Washer Lock 3/8" Hex Nut 3/8"-16 Bolt 3/8"-16x 1" Washer Lock 3/8" Washer Fender 3/8" Lever Towarm RH Trunion Zerk-Grease STR 1/4"-28 Lever Towarm RH Towarn Assembly RH Towarm Assembnly LH (not shown) Drill Bushing Towarm Chain Towarm Support Spring

Part # 7636625 7563343 7976700 7721563 7962262 7561262 7721563 7962262 7971262 9524001 9906600 5997500 9524000 9255107 9255106 4150625 9268310 5780054

Pg.#

2.7

Note: Right and Left assemblies are identical

29

Towarm Assembly 1 5 6

7

4 3 2

8 9

11 10

Item 1 2 3 4 5 6 7 8 9 10 11

Qty. 1 1 1 1 1 1 1 1 1 1 1 2 1

Description 1/2" Retaining Pin, Towarm Adjustment 100mm Internal Retaining Ring Wheel Roller Bearing Rim Roller Tire For Ball Bearing Washer Towarm 3/8" Washer Lock 3/8" Bolt 3/8"-16x 1" Shaft Roller MTG Towarm LH Shaft Roller MTG Towarm RH (not shown) Arm Tow Hitch LH Arm Tow Hitch RH (not shown) 90mm Side Thrust Bearing Roller, Tire Side

Note: Right and Left Sides are assembled identically.

30

Part # 7636510 7696100 4070300 9278711 9955001 7962262 7739567 9242805 9242806 9029100 9029101 4070100 9211600

Pg.#

Screed Lift Bracket Assembly

1

7

6 2 5

Item 1 2 3 4

5 6 7

Qty. 1 1 2 3 3 3 1 1 1

4

3

Description 413 Hopper Weldment Screed Lift Bracket Screed Pin Arm Hook-Up Anchoring Pin HHCS 5/16"-18x1-1/4" Washer Flat 5/16" Top Anchor Pin, Wing Cylinder Screed Lift Cylinder Screed Lift Arm

Part # 9980400 9136200 9636002 9636000 7721525 7962254 9636102 3220342 9029400

Pg.#

31

Tailgate Hook Weldment

1 2 3 4

5

6

7

Item 1 2 3 4 5 6 7

Qty. 3 3 1 2 2 2 2 1

Description Hook Tailgate Rubber Grip Center Chain Chain 18" Side Chain Hex Nut 3/4"-10 Bolt 3/4"-10x 2-1/2" Screed Lift Arm

Note: Right and Left sides are identical

32

Part # 9475000 5449413 9268400 9268300 9268200 7571310 7725799 9029400

Pg.#

Wing Assembly

1

2

6

4 3

5

Item 1

Qty. Description 1 413 Wing RH 1 413 Wing LH (Not Shown) 2 413 Wing Pin (Not Shown) 2 1 Clevis Pin 1/2"x 1" 3 1 Wing Cylinder 4 1 Cylinder Pin 1" 5 1 413 Hopper Weldment 6 1 Bulkhead Weld RH 1 Bulkhead Weld LH (Not Shown) Note: Right and Left Assemblies are identical.

Part # 9985411 9985412

Pg.#

7636400 3220340 7636470 9980400 9150413 9150414

33

Asphalt Splash Guard

2

1

3

Item 1 2 3

34

Qty. 1 1 1

Description Asphalt Splash Guard LH Asphalt Splash Guard RH 413 Hopper Weldment

Part # 9456001 9456002 9980400

Pg.#

413 Hopper Weldment

1

5

2

6 3 4 7

Item 1 2 3 4 5 6 7

Qty. 1 2 2 1 1 2 1 1

Description 413 Hopper Weldment Hopper Front Support Brace Gate Cylinder Anchor Gate LH Gate RH Key- 413 Hopper Gate Cylinder LH Gate Cylinder RH

Part # 9980400 9134010 9021040 9245213 9124214 9515375

Pg.#

35

Hydrualic Tank Assembly 1 2 3 4

17

5

16 6 7

15

8

9 14

10 13

11 12

Item 1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17

36

Qty. 8 8 2 2 1 1 1 1 1 1 2 1 1 1 4 1 1 8 8 3 1 1

Description Hex Nut 1/4"-20 Washer Lock 1/4" Cover Plate,Hydraulic Tank Gasket Hydraulic Tank Hydraulic Tank Weldment Closed Nipple 3/4" Filter Return Drain Manifold Hydraulic Fitting Adaptor 12MOR-12MP Hydraulic Fitting EL90 8MJ-8MOR Hydraulic Fitting Plug SH-8MOR Hydraulic FittingTee 6MJ-6MJ-8MOR Electric Pump Power Unit Pump Mounting Outer Ring HHCS 5/16"-18x 2-1/2" Hydraulic Pump Mounting Ring Gasket, Hydraulic Tank Pump Mounting HHCS 5/16"-18x 3/4" Seal Washer (Located Internally/Not Shown) Suction Strainer 3/4" (Located Internally) Sight Temperature Gauge Fuel Cap

Part # 7561246 7962246 9208805 9208802 9871106 3420752 3284075 9539413 3303555 3340415 3367415 3381400 3662280 9698001 7721533 9698000 9444010 7721519 4761000 3284130 3445100 5159813

Pg.#

O.3

Diesel Tank Assembly

1 2

Item 1 2 3 4 5

Qty. 1 1 4 4 1

Description Diesel Tank Weldment Gasket, Hydraulic & Diesel Tanks Hex Nut 1/4"-20 Washer Lock 1/4", Med. Cover Plate, Hydraulic & Diesel Tanks

4

3

5

Part # 9871110 9208802 7561246 7962246 9208805

Pg.#

37

Valve Assembly,400 Gate Control

1

2

3

Item 1 2 3

38

Qty. 2 1 4

Description Adjustable Valve Needle w/Knob Valve Body for Gate Control Fitting Hydraulic Adaptor 6MJFO-6MOR

Part # 3939200 9105101 3300344

Pg.#

Screed Screw Assembly

1 2

**Models 213 and 313 only**

3 Item 1 2 3 4 5 6

4

5

Qty. 1 1 1 1 1 2 1 4

Description Depth Adjustment Crank Roll Pin 3/8" x 1-1/2" 413 Hopper Weldment 2 pc. Collar 1.25 Depth Adjustment Screw 72mm Screed Screw Housing Bearing, 1-1/4" Bore Washer Lock, 1/2"

Part# 9225412 7636567 9980400 1195400 9225215 9493090 4074100 7962278

Note: Right and Left sides are identical 6

1

18

Power Depth Control Model 413 2

19

3

17 4 16 5 6 15 14

13

7 8

12 9 11

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Qty. 1 1 2 2 1 1 1 1 1 1 1 2 1 2 2 1 1 1 2

Description Motor (Screw) CHAR-LYNN 101-18 Pin Roll 5/16 X 1-3/4 End,SPHER Rod Male 1/2-20 RH Nut Hex Self Locking 1/2-13 Coupling-HYD MTR/Screed Screw Pin Roll 3/8 X 1-3/4 Extension Long Grease Zerk Zerk Grease-STR 1/4 28 Collar Split 1.125 Screw-SCRD Depth ADJ 813/413 Nut Spherical Adjusting 813 HHCS G5P 1/2-13x11/2 Anchor-Screed Screw HYD MTR Washer,Lock 3/8 PLTD HHCS G5P 3/8-16 X 1.

Pin Cotter 3\32X2 Yoke-HYD MTR Anchor 413 1992 Ball Socket .75 ID X 2 OD Nut Hex Self Locking 1/2-20

Part# 3549745 7636525 5251704 7571278 9215013 7636568 9273900 5997500 5195298 9225216 9576453 7721652 9021451 7962262 7721563 7636580 9994400 5051220 7571280

10

39

Screed Assemblies

4

3

5

6

1

Item 1 2 3 4 5

40

Qty.

Description Screed Weldment Wear Plates (Not Shown) Screed Back Assembly-Inside Screed Back Assembly-Outside Screed Crown Adjustment Assembly Screed Burner Assembly Blade Assembly Auger Assembly

Pg.# 41 42 43 44 45 45 46-47 48

Screed Weldment Assembly

8 7

6

3

2 1

4 5

Item 1 2 3 4 5 6

7 8

Qty. 1 1 2 1 4 4 2 12 2 2 2 1 1

Description Screed Weldment LH Screed Weldment RH Replaceable Screed Nose Front Spanner Plate Screed Tube Flange Guide Tube Retaining Ring (not shown) HHCS G5P 5/8"-11 x 7" Washer Flat 5/8" USS PLTD Washer Lock 5/8" PLTD Hex Nut 5/8"-11 PLTD 413 Single Step Spanner Plate Rear Out Spanner Plate Inner

Part # 9980110 9980111 9557114 9283040 9437100 7698000 7721775 7958294 7962294 7569214 9852901 9283020 9283021

Pg.#

41

Screed Wear Plates

1 2

3

Item 1 2 3

42

Qty. 1 1 1 6

Description Wear Plate Screed Extention Wear Plate LH Screed ExtentionWearPlate RH(not shown) Shim Wear Plate

Part # 9646000 9646006 9646007 9773015

Pg.#

Screed Back Assembly - Inside

2

3

1

Item 1

2 3

4

4

Qty. 2 1 1 1 1 1 1 1 6 2 1 2 2 2

Description Tube Guide LH Grease Zerk 1/8"-27 WPT Long Grease Zerk 1/8"-27 Female WPT Extention-Grease Zerk Screed Extention Cylinder Heat Shield Assembly Heat Shield Outer Heat Shield Spacers Anchor-Screed Cylinder Clevis Pin 3/4" x2" Cotter Pin 1/8" x 1 3/4" HHCS G5P 1/2"-13 x 1 3/4" Washer Lock 1/2" PLTD Hex Nut 1/2" PLTD

Part # 9458000 5997330 5997332 9273200 3220124 9771000 9771002 9263501 9136032 7636460 7636600 7721654 7962278 7561278

Pg.#

NOTE: Left and Right Hand Assemblies Are Identical.

43

Screed Back Assembly - Outside

2 1 3 4

Item 1 2 3 4

Qty. 1 1 2 4 2

Description Burner Cover LH Burner Cover RH Screed Hose Trough w/ Bulkheads Burner Hold-down Screed Hose Cover

NOTE: Left and Right Hand Assemblies Are Identical.

44

Part # 9269156 9269155 9906510 9474402 9216420

Pg.#

Screed Crown Adjustment Assembly Screed Burner Assembly

1

6 2

3

4

5 7

Item 1 2 3 4 5

6 7

Qty. 2 1 1 1 1 1 1 1 1 1 1 1 2 2

Description Center Divider Spacer Scale Indicator Screed Scale Adjusting Rod Scale Indicator Spring - Ratchet Lever Tie Rod End ES330 RH Tie Rod End ES330 LH Rubber Grip For Crown Jack Ratchet Cover Spring Loaded Ratchet Handle Weld 96 Turnbuckle Spring Spanner Plate Propane Burner Valve Assembly Propane Burner Assembly

Part # 9791807 9218554 9712002 9218857 4793548 5251330 5251331 5449813 9678008 9678011 9921011 4793547 9940100 9257512

Pg.#

NOTE: Left and Right Hand Assemblies Are Identical on Numbers 6 and 7.

45

Blade Assembly

1 2

3

5

4

Item 1 2 3 4 5

Qty. 1 1 1 4 2 3

Description Screed Extention Clamp LH Screed Extention Blade LH Screed Extention Blade RH (not shown) Shim Screed Extention Clamp Standard Screed Extention Nose Double Nut Special

NOTE: Left and Right Hand Assemblies Are Identical.

46

Part # 9183055 9093032 9093033 9773030 9557015 9577000

Pg.#

Blade Assembly 1

9 8 7

2

6

3

5

4

Item 1 2 3 4 5 6 7 8 9

Qty. 1 1 1 1 1 1 1 1 1 2 1

Description Screed Extention Tube-Top LH Screed Extention Tube-Bottom LH Bolt-Up End Blade LH Bolt-Up End Blade RH (not shown) Standard Screed Extention End LH StandardScreedExt. EndRH(not shown) Auger Motor Auger Limit Switch Tube Clamp Auger Motor Tube Roll Pin 3/8" x 1 3/4

Part # 9907113 9907112 9093300 9093301 9250011 9250012 3549752 9860200 9183101 9908010 9636568

Pg.#

NOTE: Left and Right Hand Assemblies Are Identical.

47

Auger Assembly

2 3 1

Item 1

2 3

Qty. 2 2 2 6 12 1 1 1 1 1

Description Bearing w/ Collar Flange CARR G5P 1/2"-13 x 1-1/2 CARR G5P 1/2"-13 x 1-1/2 Hex Nut 1/2-13 Auger 8" LH Auger 8" RH Universal Joint LH Universal Joint RH Roll Pin 3/8" x 2

NOTE: Left and Right Hand Assemblies Are Identical.

48

Part # 4070200 4437081 7109648 7109652 7561278 9035001 9035002 9512010 9512010 7636571

Pg.#

Electrical Scheme

+

1

-

GRN 2

2

MOTOR ALT

AMPS SOL 1

MOTOR STARTER

SOL 2 OFF

AUX PUMP MOTOR

RUN R1

AUX PUMP

START

MOTOR KILL WIRE GROUND TO KILL

S1 BAT

ST

START SOL

OOOX FUSE 1 15 AMP

IGN

GRN 2

R1 ENGINE RUN

OOXX FUSE 2 15 AMP

ACC

R2 AUX PUMP STOP

XOXO

KEY SWITCH

0

0

0

0

0

HOUR METER

DIESEL SPRAY OFF

ON

R2

S2 AUX PUMP SOL

2

LH CONTROL PANEL

RH CONTROL PANEL 2

LH AUGER AUTO MAN

XO

LH AUGER LIMIT

OFF FWD REV

AC -

DIODE BRIDGE

+

XOO OX

RH AUGER AUTO MAN

XO

DUMP VALVE COIL GRN 2

AC

OOX

REV VALVE COIL GRN 2

RH AUGER LIMIT FWD VALVE COIL

OFF FWD REV

DIODE BRIDGE

XOO OOX

2

GRN 2

AC -

OX

GRN 2

FWD VALVE COIL GRN 2

+

DUMP VALVE COIL

AC REV VALVE COIL

49

YELLOW

PURPLE

BLK 14-2

WHT 13-2

PUR 16-1

PUMP SPRAY DIESEL

RH

ORANGE

B

A

P16

D

C

B

BLACK

WHITE

PURPLE

YELLOW

BLUE

A

C

BLACK

LH AUGER LIMIT SWITCH

B

WHITE

HYD VALVE AREA

NCCOM

NO

NCCOM

NO

NCCOM

NO

NCCOM

LH CONTROL PANEL

WHITE

BLACK

WHITE

BLK 12

A

P15

YEL 18-1

BLU 15

WHITE

BLACK

WHITE

BLACK

WHITE

MAN

LH AUGER AUTO-MAN SWITCH

AUTO

BLUE 15 ORANGE

ORANGE

ORG 10-2

REV

LH AUGER FEED-REV SWITCH

FEED

BLU 15

NO

AC

BLACK

WHITE

-

WHITE

BLACK

WHITE

BLACK

WHITE

BLACK

WHITE

BLACK

P14 PUR 16

BLU 15

B

LH REV

LH FEED

A

RH CONTROL PANEL

COM NC

NO

COM NC

NO

COM NC

+

PINK 19 AC

NO COM NC

WHITE

BLK 14

WHT 13

PURPLE

YELLOW

BLUE

ORANGE

VALVE STACK GROUNDING LUG

RH

B

DUMP

A

LH

B

BLK 14-2

BLK 14-1

WHT 13-2 WHT 13-1

PUR 21

YEL 23

BLU 20

ORG 10-1

DUMP

A

P25

REV

RH AUGER FEED-REV SWITCH

FEED

PURPLE ORG 10-2

ORANGE

WHITE

YELLOW

P26

MAN

RH AUGER AUTO-MAN SWITCH

AUTO

GRN 2-6

NO

PUR 16-1

ORANGE PINK 19

BLACK

YEL 18-1

BLUE GRN 2-2 GRN 2-6

WHITE

GRN 2-8

P10

GRN 2-1

BLACK

GRN 2-5 B

RH REV

RH FEED

A

PUR 21-2

BLU 20

P24

AC

ACC

BLACK

WHITE

-

+

PINK 24 AC

IGN

START

KEY SWITCH BATT

NAPA KS6180

A

B

C

2

AMPS

RH AUGER LIMIT SWITCH

1-2

1

FUSE 2 15 AMP

INSTRUMENT PANEL

2

BLACK

3

1

WHITE

P23

NO

PINK 24

GRN 2-5 GRN 2-4 GRN 2-3

GRN 2-4

YEL 18 PUR 16

2 1

RED 1-1

COM NC

11

ON

1

2

1 5

2

1 5

2

BLK

4

3

HOUR METER

0 0 0 0 0

BLACK

BRN 7

BLK 3 10 GA BRN 7

BRN

P1

ORANGE 3

BLK

BLK

HOPPER F GROUND

2

ORANGE 10-

GREEN 2-2 RED 6

GRN TO OIL PRESS SW.

WHT-WHT

BROWN 7

BLACK 12 WHT 13-1

2 GA

ENGINE

NEG

2

GREEN 2-2

BLK 12

BATTERY

PUR-RED

GRN JUMPER

BRN 7

RED 6

STARTER

BLU-RED

STARTER SOLENOID

AUXILLARY PUMP

AUX. PUMP SOLENOID

RED 1 (2 GA)

POS

INSTRUMENT PANEL GROUND LUG

GREEN 2-3

BLU

BLACK

3 4

BLU

BLACK

AUX. PUMP DEFEAT RELAY (R1)

RED

BLACK

ENGINE RUN RELAY (R2)

ORANGE 3-1

BLK 12

FUSE 1 15 AMP

DIESEL SPRAY

OFF

BLK 3

NCCOM

P13

4 3

YEL 18-2 B

YEL 23-2 B

A

PUR 16 YEL 18

B

P11

GRN 2-2 A

NO

GRN 2-8

P21 GRN 2-3

P12

PUR 21-3

P20

B

YEL 23-1

A

-1 14

P22

D

BLU 20 YEL 23

C

PUR 21

B

LK B

PUR 21-3 PUR 21-2

F

PUR 21-1

A

RED 1-1 (12 GA)

E

BLK 1-3 (6 GA)

D

GREEN 2-1

C

GREEN 2-2

B

B

50 A

A

BLACK

Electrical Diagram

4

A

YEL 23-1

PUR 16-3

PUR 16-2

HYDRAULIC RESERVIOR

LH SCREED DEPTH SCREW

LH SCREED EXTENSION

WINGS

LH GATE

TOW ARMS

8CC

4CC

4CC

LH SCREED SCREW

SCREED LIFT CYLINDER

RH SCREED SCREW

RH SCREE EXTENSION CYL.

RH WING CYLINDER

FULLY OPEN THESE VALVES AND EITHER HANDLE WILL OPERATE BOTH GATES. FULLY CLOSE BOTH VALVES AND GATES RH GATE CYLINDER ARE OPERATED BY THEIR RESPECTIVE VALVE HANDLES.

RH HAND PUMP

MAIN HYDRAULIC PUMPS

LH SCREED EXTENSION CYL.

LH WING CYLINDER

LH GATE CYLINDER

TOW ARM CYLINDER

LH HAND PUMP

MOTOR ELECTRIC PUMP

ENGINE

RH SCREED DEPTH SCREW

RH SCREED EXTENSION

WINGS

RH GATE

SCREED LIFT

TO 2000 PSI

TO 2000 PSI

SET RELIEF VALVE

SET RELIEF VALVE

AUGER CONTROL VALVE PACKAGE

SET RELIEF V

Hydraulic Scheme

51

Hydraulic Diagram B 1

A 2

3

8

7

16

9 11

17

15

10

E

D

5 C 6

4

14

F

I

H 18

G

19 20

13

12 23 25 24

27 26

K 28 33

21

J

31 M 32

29 L 30

N 34

22 36

35

O 37 38 39 41 42

40

43

Q P 44

48

50

45 49

51

S

46

T

R 47

U

52

52

53 V

Item A B C D E F G H I J K L M N O P Q R S T U V

Part Screed Cyl. LH ScreedLiftMotorLH Screed Cyl. RH ScreedLiftMotorRH Valve Bank LH Gate Cyl. LH& RH 400 Gate Control Screed Lift Cyl. Valve Bank RH Wing Cyl. LH Manafold Towarm Cyl LH Towarm Cyl RH Wing Cyl. RH Hydrualic Tank Triple Pump Flow Divider Auger Manifold Hand Pump LH Hand Pump RH Lines to Auger LH Lines to Auger RH

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

Hydraulic Diadram Hose # 1479500-0580 1479500-0635 1479500-0480 1479500-0480 1479500-0635 1479500-0580 1479500-0480 1479500-0480 1479475-0350 1479475-0350 1479475-0350 1479475-0350 1479550-0340 1479475-0350 1479550-0315 1479475-0350 1479500-0285 1479500-0220 1479500-0480 1479500-0480 1479500-0390 1479500-0390 1479500-0245 1479500-0245 9350406 9350405 1479500-0480 1479500-0480 1479500-0570 1479500-0680 1479500-0680 1479500-0570 1479500-0390 1479500-0390 1481525-0650 1481525-0180 1481600-1110 1482525-1100 1479525-0300 1479500-1305 1484800-0150 1484800-0140 1484800-0140 9908103 9908100 9908101 9908102 1481525-0510 1479500-0160 1481525-0335 1479500-0155 1481600-0350 1481600-0380

53

This page intentionally left blank.

54

Kohler Engine Manual

55

Kohler Engine Manual

56

Kohler Engine Manual

57

Kohler Engine Manual

58

Kohler Engine Manual

59

Kohler Engine Manual

60

Kohler Engine Manual

61

Kohler Engine Manual

62

Kohler Engine Manual

63

Kohler Engine Manual

64

Kohler Engine Manual

65

Kohler Engine Manual

66

Kohler Engine Manual

67

Kohler Engine Manual

68

Kohler Engine Manual

69

Kohler Engine Manual

70

Honda Engine Manual

71

Honda Engine Manual

72

Honda Engine Manual

73

Honda Engine Manual

74

Honda Engine Manual

75

Honda Engine Manual

76

Honda Engine Manual

77

Honda Engine Manual

78

Honda Engine Manual

79

Honda Engine Manual

80

Honda Engine Manual

81

Honda Engine Manual

82

Honda Engine Manual

83

Honda Engine Manual

84

Honda Engine Manual

85

Honda Engine Manual

86

Honda Engine Manual

87

Honda Engine Manual

88

Honda Engine Manual

89

Honda Engine Manual

90

Honda Engine Manual

91

Honda Engine Manual

92

Honda Engine Manual

93

Honda Engine Manual

94

Honda Engine Manual

95

Honda Engine Manual

96

Honda Engine Manual

97

Honda Engine Manual

98

Honda Engine Manual

99

Honda Engine Manual

100

Honda Engine Manual

101

Honda Engine Manual

102

Honda Engine Manual

103

Honda Engine Manual

104

Honda Engine Manual

105

Honda Engine Manual

106

Honda Engine Manual

107

Honda Engine Manual

108

Honda Engine Manual

109

Honda Engine Manual

110

Honda Engine Manual

111

Honda Engine Manual

112

Honda Engine Manual

113

Honda Engine Manual

114

Honda Engine Manual

115

Honda Engine Manual

116

Honda Engine Manual

117

Honda Engine Manual

118

Honda Engine Manual

119

Honda Engine Manual

120

Honda Engine Manual

121

Honda Engine Manual

122

Honda Engine Manual

123

Honda Engine Manual

124

Honda Engine Manual

125

Honda Engine Manual

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

WARRANTY BOMAG PAVING PRODUCTS EQUIPMENT IS WARRANTED FOR A PERIOD OF SIX (6) MONTHS FROM “IN SERVICE DATE” ESTABLISHED BY THE “WARRANTY REGISTRATION FORM” COMPLETED, SIGNED AND FILED WITH BOMAG PAVING PRODUCTS WHEN THE UNIT IS INITIALLY PLACED IN SERVICE. FAILURE TO TRANSMIT TO BOMAG PAVING PRODUCTS THE COMPLETED AND SIGNED WARRANTY REGISTRATION FORM WITHIN 10 DAYS OF PLACING THE EQUIPMENT IN SERVICE WILL DISQUALIFY THIS WARRANTY ON THE EQUIPMENT. THIS WARRANTS BOMAG PAVING PRODUCTS EQUIPMENT TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP. NO OBLIGATION IS ASSUMED BY BOMAG PAVING PRODUCTS FOR EQUIPMENT RENDERED DEFECTIVE OR DAMAGED THROUGH NORMAL WEAR, IMPROPER APPLICATION OR MISUSE. BOMAG PAVING PRODUCTS OBLIGATION UNDER THIS WARRANTY SHALL BE LIMITED TO REPAIR OR EXCHANGE, AT OUR OPTION, F.O.B. OUR FACTORY, OF ANY BOMAG PAVING PRODUCTS EQUIPMENT OR PART WHICH PROVES TO BE DEFECTIVE, BOMAG PAVING PRODUCTS ASSUMES NO OBLIGATION FOR CLAIMS THAT ARE INCIDENTAL TO THE REPAIR OR EXCHANGE OF OUR PRODUCTS. THIS WARRANTY IS SUBJECT TO BOMAG PAVING PRODUCTS BEING NOTIFIED IMMEDIATELY UPON THE DISCOVERY OF ANY DEFECTIVE MATERIAL AND/OR WORKMANSHIP WITHIN THE SAID SIX (6) MONTH WARRANTY PERIOD, AND THE HOLDING OF THE ITEM FOR BOMAG PAVING PRODUCTS INSPECTION AND DISPOSITION. ANY AFFIRMATION OF FACT OR PROMISE MADE BY ANY AGENT, DISTRIBUTOR, DEALER, OR EMPLOYEE OF BOMAG PAVING PRODUCTS SHALL NOT BE DEEMED TO CREATE AN EXPRESS WARRANTY THAT THE GOODS SHALL CONFORM TO THE AFFIRMATION OR PROMISE. THE BUYER IS SOLELY RESPONSIBLE FOR DETERMINING SUITABILITY FOR USE. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART. THIS WARRANTY STATES OUR ENTIRE AND EXCLUSIVE LIABILITY AND THE BUYER’S EXCLUSIVE REMEDY FOR CLAIM OF DAMAGES IN CONNECTION WITH THE SALE OR USE OF BOMAG PAVING PRODUCTS EQUIPMENT. IN NO EVENT SHALL BOMAG PAVING PRODUCTS BE MADE LIABLE TO CONSEQUENTIAL OR SPECIAL DAMAGES WHATSOEVER, NOR FOR ANY SUM IN EXCESS OF THE PRICE RECEIVED FOR THE PRODUCTS FOR WHICH THE LIABILITY IS CLAIMED OR ASSOCIATED. BOMAG PAVING PRODUCTS RESERVES THE RIGHT TO CHANGE THE DESIGN AND SPECIFICATIONS OF OUR PRODUCTS WITHOUT NOTICE, OR INCURRED OBLIGATIONS.

FOR FURTHER INFORMATION CONTACT DEALERSHIP.

Tow-Type 0222413 CVR

4/25/05

11:15 AM

Page 1

Operations / Instruction / Parts

113 / 213 / 313 / 413

TOW-TYPE PAVERS

Printed in U.S.A.

BOMAG Paving Products 618 N. Enterprise Dr. Warrensburg, MO 64093

Catalog Number

0222413

5/05