Part number 47657030 1st edition English April 2014 SERVICE MANUAL Guardian™ SP.240R Guardian™ SP.275R Tier 3 Sprayer PIN YDYM00602 and above
INTRODUCTION
[10.001] Engine and crankcase
[10.202] Air cleaners and lines
[10.206] Fuel filters .
[10.210] Lift pump and lines
[10.216]
[10.254] Intake and exhaust manifolds and muf fler
12] Power shuttle transmission
Gearbox internal components
[21.200] Dropbox
Front axle system
Powered front axle front axle
Rear axle system
[27.100] Powered rear axle
[27.106] Rear bevel gear set and dif ferential
Brakes and controls
[35.106]
Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4
Fuel tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6 Engine cooling system Fan and drive T ransmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic
brakes
lock Hydraulic systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
service
10] Parking brake parking
systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.1
[35.000] Hydraulic
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.2 47657030 01/04/2014
V ariable displacement pump
Reservoir , cooler , and filters
Pneumatic system
Pneumatic system
[36.200] Pneumatic operated components
Frames and ballasting
[39.100] Frame
Steering
Hydraulic control components
Pump
Cylinders
Wheels
[44.51 Front wheels
[44.520] Rear wheels
Heating
Air conditioning
Electrical systems
Engine control system
[55.100] Harnesses and connectors
[55.050] Heating, V entilation, and (HV
[55.201]
[55.301] Alternator
[55.000]
[55.640] Electronic
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36.2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cab climate control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.2
AC) control system . . . . . . . . . . . . . . . . . 55.3
Engine starting system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.5 Battery [55.521]
controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.7
Cab sprayer
Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.8
modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.9 Spraying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47657030 01/04/2014
10] Chemical spraying
Foam marking system
Accessories
Accessories
Platform, cab, bodywork, and decals
Machine shields and guards operator seat
[90.150] Cab .
[90.151] Cab interior .
1
Spraying pump
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.4 47657030
01/04/2014
47657030 01/04/2014 1
INTRODUCTION
Basic instructions - Important notice regarding equipment servicing
Basic instructions - Shop and assembly
General specification - T ire and rim repair
Capacities Lubricants and fluid capacities
Product identification Machine serial number
Product identification (*)
Product identification (*)
Contents INTRODUCTION Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety rules (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety rules - Ecology and the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 T orque - Minimum tightening torques for normal assembly (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 T orque - Standard torque data for hydraulics (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (*) See content for specific models 47657030 01/04/2014 2
Personal safety
W ARNING
Maintenance hazard!
Before you start servicing the machine, attach a NOT OPERA warning tag the machine a visible area.
Failure comply could result death serious injury
Attach a NOT OPERA AG) the machine area that clearly visible whenever the machine not operating properly and / requires
Complete the tag information for the "REASON" the tag attached describing the malfunction service V alidate the reason for attaching the tag signing your name the designated area the The tag should only removed the person who signed and attached the after validating the repairs services have been completed.
NOT REMOVE THIS T AG! - arning) The tag should only removed the person who signed and attached the after validating the repairs services have been
See Other Side - (Reference additional information opposite side the
CNH Part Number - (Request this part number from you Service Parts Dealer obtain this NOT OPERA
NOT OPERA - arning!)
REASON - (Area for describing malfunction service required before
F Signed - (Signature area - signed the person validating the reason for installation the
INTRODUCTION
W0004A
(A) (D)
(E) (B)
(C) 87358697 1
(F)
T Components
47657030 01/04/2014 3
Safety rules
INTRODUCTION
BT09A213 1 47657030 01/04/2014 4
Safety rules
Personal safety
This the safety alert used alert you potential personal injury Obey all safety messages that follow this symbol avoid possible death injury
Throughout this manual you will find the signal words W and CAUTION followed special These precautions are intended for the personal safety you and those working with
Read and understand all the safety messages this manual before you operate service the
DANGER indicates a hazardous situation not will result death serious injury
W ARNING indicates a hazardous situation not could result death serious injury
CAUTION indicates a hazardous situation not could result minor moderate injury
T O FOLLOW
Machine safety
NOTICE: Notice indicates a situation that, not avoided, could result machine property damage.
Throughout this manual you will find the signal word Notice followed special instructions prevent machine property damage. The word Notice used address practices not related personal safety .
Information
NOTE: Note indicates additional information that clarifies other information this
Throughout this manual you will find the word Note followed additional information about a step, other information the The word Note not intended address personal safety property
INTRODUCTION
DEA
F AILURE
DANGER, W ARNING, AND CAUTION MESSAGES COULD RESUL T
SERIOUS INJUR Y .
47657030 01/04/2014 5
Safety rules - Ecology and the environment
Soil, air , and water are vital factors agriculture and life general. When legislation does not yet rule the treatment some the substances required advanced technology , sound judgment should govern the use and disposal products a chemical and petrochemical
NOTE: The following are recommendations that may assistance:
• Become acquainted with and ensure that you understand the relative legislation applicable your country
• Where legislation obtain information from suppliers cleaning with regard their fect man and nature and how safely and dispose these
• Agricultural consultants many cases, able help you
Helpful hints
• A void filling tanks using cans inappropriate pressurized fuel delivery systems that may cause considerable
• general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most them contain substances that may harmful your
• Modern oils contain not burn contaminated fuels and waste oils ordinary heating
• A void spillage when draining f used engine coolant gearbox and hydraulic brake not mix drained brake fluids fuels with Store them safely until they can disposed a proper way comply with local legislation and available
• Modern coolant antifreeze and other should replaced every two They should not allowed get into the soil, but should collected and disposed properly .
• not open the air - conditioning system contains gases that should not released into the Y our NEW HOLLAND dealer air conditioning specialist has a special extractor for this purpose and will have recharge the system properly
• Repair any leaks defects the engine cooling hydraulic system immediately
• not increase the pressure a pressurized circuit this may lead a component
• Protect hoses during welding penetrating weld splatter may burn a hole weaken allowing the loss oils, coolant, etc.
INTRODUCTION
47657030 01/04/2014 6
T orque - Minimum tightening torques for normal assembly
NOTE: through hardware torque specifications are shown poundinches. M10 through M24 hardware torque specifications are shown pound -
INTRODUCTION
METRIC NON - FLANGED HARDW ARE NOM. SIZE CLASS 8.8 BOL T and CLASS 8 NUT CLASS 10.9 BOL T and CLASS NUT LOCKNUT CL.8 W / CL8.8 BOL T LOCKNUT CL.10 W / CL10.9 BOL T UNPLA TED PLA TED W / ZnCr UNPLA TED PLA TED W / ZnCr N·m ( ) N·m ( ) N·m ( ) N·m ( ) 2 N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) 4 N·m ( ) N·m ( ) 7.5 N·m ( ) N·m ( ) 1 1 N·m ( ) N·m ( 128 ) 6.8 N·m ( ) N·m ( ) N·m ( 163 ) N·m ( 217 ) N·m ( 234 ) N·m ( 1 ) N·m ( 151 ) N·m ( 212 ) M10 ( ) N·m ( ) ( ) N·m ( ) N·m ( ) N·m ( ) M12 ( ) ( ) ( ) 121 ( ) ( ) ( ) M16 158 ( 1 ) 210 ( 155 ) 225 ( 166 ) 301 ( 222 ) 143 ( 106 ) 205 ( 151 ) M20 319 ( 235 ) 425 N·m ( 313 ) 440 ( 325 ) 587 ( 433 ) 290 ( 214 ) 400 ( 295 ) M24 551 N·m ( 410 ) 735 N·m ( 500 ) 762 N·m ( 560 ) 1016 N·m ( 750 ) 501 N·m ( 370 ) 693 N·m ( 510 )
47657030 01/04/2014 7
IDENTIFICA TION
Metric Hex head and carriage bolts, classes 5.6 and
INTRODUCTION
ARE NOM. SIZE CLASS 8.8 BOL T and CLASS 8 NUT CLASS 10.9 BOL T and CLASS NUT LOCKNUT CL.8 W / CL8.8 BOL T LOCKNUT CL.10 W / CL10.9 BOL T UNPLA TED PLA TED W / ZnCr UNPLA TED PLA TED W / ZnCr 2.4 N·m ( ) 3.2 N·m ( ) 3.5 N·m ( ) 4.6 N·m ( ) 2.2 N·m ( ) 3.1 N·m ( ) 4.9 N·m ( ) 6.5 N·m ( ) 7.0 N·m ( ) 9.4 N·m ( ) 4.4 N·m ( ) 6.4 N·m ( ) 8.3 ( ) 1 1 ( ) ( 105 ) ( 141 ) 7.5 ( ) 1 1 ( ) ( 179 ) ( 240 ) ( 257 ) ( 343 ) ( 163 ) ( 240 ) M10 N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) M12 N·m ( ) N·m ( ) 100 N·m ( ) 134 N·m ( ) N·m ( ) N·m ( ) M16 174 N·m ( 128 ) 231 N·m ( 171 ) 248 N·m ( 183 ) 331 N·m ( 244 ) 158 N·m ( 1 ) 226 N·m ( 167 ) M20 350 N·m ( 259 ) 467 N·m ( 345 ) 484 N·m ( 357 ) 645 N·m ( 476 ) 318 N·m ( 235 ) 440 N·m ( 325 ) M24 607 N·m ( 447 ) 809 N·m ( 597 ) 838 N·m ( 618 ) 1 1 N·m ( 824 ) 552 N·m ( 407 )
METRIC FLANGED HARDW
20083680 1 Identification Property Class Metric
nuts
20083681 2 47657030 01/04/2014 8
Hex
and locknuts, classes and
INTRODUCTION Identification Property Class Clock Marking Property Class and Identification marks ° apart indicate Class and marks 120 ° apart indicate Class INCH NON - FLANGED HARDW ARE NOMINAL SIZE SAE GRADE 5 BOL T and NUT SAE GRADE 8 BOL T and NUT LOCKNUT GrB W / Gr5 BOL T LOCKNUT GrC W / Gr8 BOL T UNPLA TED PLA TED SIL VER PLA TED W / ZnCr GOLD UNPLA TED PLA TED SIL VER PLA TED W / ZnCr GOLD 1 / 4 8 N·m ( ) 1 1 N·m ( ) ( 106 ) ( 142 ) 8.5 ( ) 12.2 N·m ( 109 ) 5 / ( 150 ) ( 204 ) ( 212 ) ( 283 ) 17.5 ( 155 ) ( 220 ) 3 / 8 ( ) ( ) ( ) ( ) N·m ( ) N·m ( ) 7 / N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) N·m ( ) 1 / 2 N·m ( ) N·m ( ) 104 N·m ( ) 139 N·m ( 103 ) N·m ( ) 108 N·m ( ) 9 / 107 N·m ( ) 142 N·m ( 105 ) 150 N·m ( 1 1 1 ) 201 N·m ( 148 ) 1 1 1 N·m ( ) 156 N·m ( 1 ) 5 / 8 147 N·m ( 108 ) 196 N·m ( 145 ) 208 N·m ( 153 ) 277 N·m ( 204 ) 153 N·m ( 1 ) 215 N·m ( 159 ) 3 / 4 261 N·m ( 193 ) 348 N·m ( 257 ) 369 N·m ( 272 ) 491 N·m ( 362 ) 271 N·m ( 200 ) 383 N·m ( 282 ) 7 / 8 420 ( 310 ) 561 ( 413 ) 594 ( 438 ) 791 ( 584 ) 437 N·m ( 323 ) 617 N·m ( 455 ) 1 630 ( 465 ) 841 ( 620 ) 890 ( 656 ) 1 187 ( 875 ) 654 ( 483 ) 924 ( 681 ) NOTE: For Imperial 1 / 4 and 5 / hardware torque specifications are shown pound - 3 / 8 through 1 hardware torque specifications are shown pound47657030 01/04/2014 9
INTRODUCTION INCH FLANGED HARDW ARE NOMINAL SIZE SAE GRADE 5 BOL T and NUT SAE GRADE 8 BOL T and NUT LOCKNUT GrF W / Gr5 BOL T LOCKNUT GrG W / Gr8 BOL T UNPLA TED PLA TED SIL VER PLA TED W / ZnCr GOLD UNPLA TED PLA TED SIL VER PLA TED W / ZnCr GOLD 1 / 4 9 ( ) N·m ( 106 ) N·m ( 1 ) N·m ( 150 ) 8 ( ) N·m ( 106 ) 5 / N·m ( 168 ) N·m ( 221 ) N·m ( 230 ) N·m ( 310 ) N·m ( 150 ) N·m ( 212 ) 3 / 8 ( ) ( ) ( ) ( ) ( ) ( ) 7 / ( ) ( ) ( ) 100 ( ) N·m ( ) N·m ( ) 1 / 2 N·m ( ) 108 N·m ( ) 1 N·m ( ) 153 N·m ( 1 ) N·m ( ) 104 N·m ( ) 9 / 1 N·m ( ) 156 N·m ( 1 ) 165 N·m ( 122 ) 221 N·m ( 163 ) 106 N·m ( ) 157 N·m ( 1 ) 5 / 8 162 N·m ( 1 ) 216 N·m ( 159 ) 228 N·m ( 168 ) 304 N·m ( 225 ) 147 N·m ( 108 ) 207 N·m ( 153 ) 3 / 4 287 N·m ( 212 ) 383 N·m ( 282 ) 405 N·m ( 299 ) 541 N·m ( 399 ) 261 N·m ( 193 ) 369 N·m ( 272 ) 7 / 8 462 N·m ( 341 ) 617 N·m ( 455 ) 653 N·m ( 482 ) 871 N·m ( 642 ) 421 N·m ( 1 ) 594 N·m ( 438 ) 1 693 N·m ( 512 ) 925 ( 682 ) 979 ( 722 ) 1305 ( 963 ) 631 N·m ( 465 ) 890 N·m ( 656 ) IDENTIFICA TION Inch Bolts and free - spinning nuts 20083682 3 Grade Marking Examples SAE Grade Identification 1 Grade 2 - Marks 4 Grade 2 Nut - Marks 2 Grade 5 - Three Marks 5 Grade 5 Nut - Marks 120 ° Apart 3 Grade 8 - Five Marks 6 Grade 8 Nut - Marks ° Apart 47657030 01/04/2014
INTRODUCTION
All Metal
optional methods) 20090268 4 Grade Identification Grade Corner Marking Method (1) Flats Marking Method (2) Clock Marking Method (3) Grade A Notches Mark Marks Grade B One Circumferential Notch Letter B Three Marks Grade C T Circumferential Notches Letter C Six Marks 47657030 01/04/2014 1 1
Inch Lock Nuts,
(Three
T orque - Standard torque data for hydraulics
INST ALLA TION ADJUST ABLE FITTINGS STRAIGHT THREAD O RING BOSSES
Lubricate the O - ring coating with a light oil
Install the O - ring the groove adjacent the metal backup washer which assembled the extreme end the groove (4)
Install the fitting into the SAE straight thread boss until the metal backup washer contacts the face the boss (5)
NOTE: not over tighten and distort the metal backup washer .
Position the fitting turning out (counterclockwise) a maximum one Holding the pad the fitting with a tighten the locknut and washer against the face the boss (6)
ANDARD T ORQUE T A FOR HYDRAULIC TUBES AND FITTINGS
TUBE NUTS FOR 37° FLARED FITTINGS O -
These torques are not recommended for tubes 12.7 ( 1 / 2 ) and larger with wall
0.889 ( ) The torque specified for ( ) wall tubes each application individually
Before installing and torquing ° flared fittings, clean the face the flare and threads with a clean solvent Loctite cleaner and apply hydraulic sealant L OCTITE ® 569 the ° flare and the
Install fitting and torque specified loosen fitting and retorque
INTRODUCTION
23085659 1
RING BOSS PLUGS ADJUST ABLE FITTING LOCKNUTS, SWIVEL JIC37° SEA SIZE TUBING THREAD SIZE T ORQUE T ORQUE 4 ( 1 / 4 ) 7 / - - N·m ( 9 - ) 8 - N·m ( 6 - ) 5 7.9 ( 5 / ) 1 / 2 - - ( - ) - ( - ) 6 9.5 ( 3 / 8 ) 9 / - - N·m ( - ) - N·m ( - ) 8 ( 1 / 2 ) 3 / 4 - - N·m ( - ) - N·m ( - ) ( 5 / 8 ) 7 / 8 - - N·m ( - ) - N·m ( - ) 19.1 ( 3 / 4 ) 1 - 1 / - 104 - 1 1 1 ( - ) - ( - ) 22.2 ( 7 / 8 ) 1 - 3 / - 122 - 136 N·m ( - 100 ) - 109 N·m ( - ) ( 1 ) 1 - 5 / - 149 - 163 N·m ( 1 - 120 ) 108 - 122 N·m ( - ) 31.8 ( 1 - 1 / 4 ) 1 - 5 / 8 - 190 - 204 ( 140 - 150 ) 129 - 158 ( - 1 ) 38.1 ( 1 - 1 / 2 ) 1 - 7 / 8 - 217 - 237 N·m ( 160 - 175 ) 163 - 190 N·m ( 120 - 140 ) 50.8 ( 2 ) 2 - 1 / 2 - 305 - 325 N·m ( 225 - 240 ) 339 - 407 N·m ( 250 - 300 )
thickness
47657030 01/04/2014
PIPE THREAD FITTING T ORQUE
Before installing and tightening pipe clean the threads with a clean solvent Loctite cleaner and apply sealant L OCTITE ® 567 PST P IPE S EALANT for all fittings including stainless steel L OCTITE ® 565 PST for most metal fittings. For high filtration / zero contamination tems use L OCTITE ® 545
INST ALLA TION ORFS - RING FLA T F ACED) FITTINGS
When installing ORFS fittings thoroughly clean both flat surfaces the fittings (1) and lubricate the O - ring (2) with light Make sure both surfaces are aligned properly T orque the fitting specified torque listed throughout the repair manual.
NOTICE: the fitting surfaces are not properly cleaned, the O - ring will not seal properly the fitting surfaces are not properly the fittings may damaged and will not seal properly
PIPE THREAD FITTING
NOTICE: Always use genuine factory replacement oils and filters ensure proper lubrication and filtration gine and hydraulic system oils.
The use proper and keeping the hydraulic system clean will extend machine and component life.
INTRODUCTION
Thread Size T orque (Maximum) 1 / 8 - N·m ( ) 1 / 4 - N·m ( ) 3 / 8 - ( ) 1 / 2 - N·m ( ) 3 / 4 - N·m ( )
5001
47657030 01/04/2014
1 183 2
Basic instructions - Important notice regarding equipment servicing
All repair and maintenance work listed this manual must carried out only qualified dealership strictly complying with the instructions and whenever the special
Anyone who performs repair and maintenance operations without complying with the procedures provided herein shall responsible for any subsequent
The manufacturer and all the organizations its distribution chain, including - without limitationnational, regional, local reject any responsibility for damages caused parts and / components not approved the facturer , including those used for the servicing repair the product manufactured marketed the manufacturer any case, warranty given attributed the product manufactured marketed the manufacturer case damages caused parts and / components not approved the manufacturer
The information this manual - - date the date the the policy the manufacturer for continuous Some information could not updated due modifications a technical commercial type, changes the laws and regulations dif ferent countries.
case refer your NEW HOLLAND Sales and Service
INTRODUCTION
47657030 01/04/2014
Basic instructions - Shop and assembly
Shimming
For each adjustment select adjusting shims and measure the adjusting shims individually using a eter , then add the recorded not rely measuring the entire shimming which may the rated value shown each
Rotating shaft seals
For correct rotating shaft seal proceed follows:
Before assembly , allow the seal soak the oil will sealing for least thirty Thoroughly clean the shaft and check that the working surface the shaft not
Position the sealing lip facing the
NOTE: W ith
hydrodynamic take into consideration the shaft rotation direction and position the grooves that they will move the fluid towards the inner side the
Coat the sealing lip with a thin layer lubricant (use oil rather than Fill the gap between the sealing lip and the dust lip double lip seals with grease.
Insert the seal its seat and press down using a flat punch seal installation not tap the seal with a hammer
While you insert the check that the seal perpendicular the When the seal make sure that the seal makes contact with the thrust
T o prevent damage the seal lip the position a protective guard during installation
- ring seals
Lubricate the O - ring seals before you insert them the This will prevent the O - ring seals from overturning and which would jeopardize sealing ficiency
Sealing compounds
Apply a sealing compound the mating surfaces when specified the Before you apply the sealing compound, prepare the surfaces directed the product container .
Spare parts
Only use CNH Original Parts NEW HOLLAND Original Parts.
Only genuine spare parts guarantee the same quality , and safety original they are the same parts that are assembled during standard production. Only CNH Original Parts NEW HOLLAND Original Parts can fer this
When ordering spare parts, always provide the following information:
• Machine model (commercial name) and Product Identification Number (PIN)
• Part number the ordered which can found the parts catalog
INTRODUCTION
O
47657030 01/04/2014
NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please
Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual
write to
admin@servicemanualperfect.com
me:
