2016 HALF TRANSFER SHAKER FEEDER 8 LANE ‐ 12 LANE ‐ 16 LANE
A&K Development Company ‐ Eugene, Oregon Phone: 541‐686‐0012 Web: www.akdco.net E‐Mail: akdco@akdco.net
2016 HALF TRANSFER SHAKER FEEDER 8 LANE ‐ 12 LANE ‐ 16 LANE
Introduction
A&K Development Introduction
Warranty Authorization Notice
Section I
Drive & Motor Assembly
Common Parts
Section II
Flex Drive Assembly
Common Parts Lubrication Schedule
Section III
Shaker Arms & Mount Assembly
Common Parts
Section IV Section IV
Spring Mount Components Spring Mount Components
C Common Parts P t
Section V
Linear Actuator Assembly
Common Parts Control Panel
Section VI
Shaker Pan Components
Common Parts Belting, Sides, Etc.
Section VII
Shaker Snout Assembly
Common Parts
Section VIII
Master Spare Parts List
All Common Parts
TOC
DEVELOPMENT COMPANY FOOD PROCESSING EQUIPMENT Tel: 541-686-0012
MANUFACTURE & DESIGN
410 Chambers Street Eugene, Oregon USA 97402
Fax: 541-485-2892 Email: akdevelop@aol.com
A&K Development Company, Inc. warrants A&K equipment and parts to be free from defects in material and workmanship on the date of purchase, for a period of one (1) processing season and the start-up of the second (2nd) processing season, and that the equipment provided by A&K shall conform to the specification and drawings. A&K will repair or replace any part of the equipment proved defective. This limited warranty applies only when equipment is properly installed, operated and maintained in accordance with A&K written recommendations. This warranty does not cover, and A&K shall not be liable for, any malfunction, damage or normal wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, improper adjustment, lack of lubrication or substitution of non A&K component parts nor shall A&K be liable for malfunction, damage or normal wear caused by the incompatibility with A&K equipment of structures, accessories, equipment or materials not supplied by A&K, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by A&K. A&K at its sole discretion determines whether the equipment is defective by reason of material or workmanship. The A&K limited warranty described in this paragraph is in lieu of any other A&K warranty. A&K makes no other warranties, express or implied, including but not limited to any implied warranties of merchantability or fitness for a particular purpose. THE SOLE AND EXCLUSIVE REMEDY for any breach of the A&K limited warranty shall be the repair or replacement for buyer, at A&K’s option and expense, of any equipment component or part manufactured by A&K, which proves to be in breach of the A&K limited warranty. Any repaired or replaced equipment component or part shall be provided F.O.B. factory.
A&K
SHALL UNDER NO CIRCUMSTANCES BE LIABLE TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR OTHER INDIRECT DAMAGES OF ANY KIND. This limited warranty and limitation of remedies gives you specified legal rights and you may also have other rights which vary from state to state.
A&K DEVELOPMENT POLICY 1. To constantly improve its products whenever it is practical to do so. 2. Reserves the right to redesign or change its equipment or component parts, without incurring any obligation to install or furnish such changes on equipment previously delivered. 3. Unauthorized changes or additions to equipment manufactured by A&K Development relieves the company of any further responsibility for warranty of operation and breakage replacement. 4. The information contained in this manual is representative of a typical system. Performance of the equipment is dependent on many factors not within the scope of the manual and should be considered in relation to the entire processing line. 5. This manual is intended only as an operation and maintenance guide for a typical system and is subject to change through revisions and additions without notification. 6. Authorization must be secured before any equipment or parts are returned for credit or replacement. When equipment or parts are returned, the freight must be prepaid or other arrangements made by A&K Development.
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8 8‐LN LN
12 12‐LN LN
16 16‐LN LN
HTS‐16‐001
WORLDWIDE MOTOR, 1 HP, 1800 RPM, 56CB BASE
1
1
1
HTS‐16‐002
SHEAVE 5/8", 60 HZ OPERATION
1
1
1
HTS‐16‐006
SHEAVE 7/8", 50 HZ OPERATION
1
1
1
HTS‐16‐003
DRIVE PULLEY
1
1
1
HTS‐16‐007
BUSHING STEEL SPLIT, DRIVE PULLEY
1
1
1
1
1
1
1
1
1
1
1
1
AK‐13‐FDS‐A037 PULLEY COVER ASSEMBLY AK‐13‐FDS‐DB‐007 PULLEY BACK HTS‐16‐004
V‐BELT, A35
PULLEY COVER ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐008
1/4"‐20 X 3/4" GRADE 5 HEX HEAD BOLT
2
2
2
HTS‐16‐009
1/4" FLAT WASHER
2
2
2
HTS‐16‐010
1/4" LOCK WASHER 1/4" LOCK WASHER
2
2
2
I‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8 8‐LN LN
12 12‐LN LN
16 16‐LN LN
AK‐15‐FDS‐013
MOTOR MOUNT, ADJUSTABLE
1
1
1
AK‐15‐FDS‐012
MOTOR MOUNT, FIXED
1
1
1
MOTOR MOUNT ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐011
1/2"‐13 X 2" HEX HEAD BOLT
2
2
2
HTS‐16‐012
1/2"‐13 X 2 1/4" BUTTON HEAD BOLT
2
2
2
HTS‐16‐013
7/16" X 3/4" GRADE 5 HEX HEAD BOLT
2
2
2
HTS‐16‐014
1/2" FLAT WASHER
4
4
4
HTS‐16‐015 HTS 16 015
1/2" CAM LOCK WASHERS (2 PER) 1/2 CAM LOCK WASHERS (2 PER)
4
4
4
I‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # HTS‐16‐001
A
WORLDWIDE MOTOR, 1 HP, 1800 RPM, 56CB BASE
B
MOTOR MOUNT, ADJUSTABLE
AK‐15‐FDS‐013
C
MOTOR MOUNT, FIXED
AK‐15‐FDS‐012
I‐3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
SHEAVE 5/8", 60 HZ OPERATION
HTS‐16‐002
B
SHEAVE 7/8", 50 HZ OPERATION /
HTS‐16‐006 S 6 006
C
DRIVE PULLEY
HTS‐16‐003
D
BUSHING STEEL SPLIT, DRIVE PULLEY
HTS‐16‐007
F
V‐BELT, A35
HTS‐16‐004
I‐4
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS DRIVE & MOTOR ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
A
PULLEY COVER ASSEMBLY
B
PULLEY PULLEY BACK BACK
PART # AK‐13‐FDS‐A037 AK 13 FDS DB 007 AK‐13‐FDS‐DB‐007
I‐5
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
E
E
18.312
D
D
2.000
C
C
7.875
.562
B
B
PART NUMBER: AK-13-FDS-DB-007 PULLEY BACK DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: ASTM A36 Steel
DrawnBy: CRAIG
FINISH: BENGAL SILVER PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS: .074
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
DATE: 4/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
3
FOOD PROCESSING EQUIPMENT
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:2.047 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
18.437 1 E
E
3
D
D
TYP. G
C
C
7.874
B
B
PARTNUMBER: AK-13-FDS-A037 PULLEY COVERWELDMENT DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: Material <not specified> ITEM NO.
PART NUMBER
MATERIAL
REV
THICKNESS
DESCRIPTION
1
AK-13-FDS-136
ASTM A36 Steel
A
.062
PULLEY COVER BASE
.062
PULLEY COVER END
1
A
.062
PULLEY COVER END
1
2
AK-11-FDS-182
ASTM A36 Steel
3
AK-11-FDS-183
ASTM A36 Steel
8
7
6
QTY. FINISH: SAFETY YELLOW 1 PRESS BRAKE INFORMATION
5
BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
THICKNESS:
DrawnBy: CRAIG
DATE:12/1/2009
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:3.674 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER FLEX DRIVE ASSEMBLY ‐ COMMON PARTS FLEX DRIVE ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART AK‐13‐CS‐A116
ITEM DESCRIPTION S O DRIVE SPRING BOARD ASSY (4 PER SET) W/ HARDWARE
AK‐13‐CS‐A116A FIBERBOARD ASSEMBLY (ONE FIBERBOARD) W/ BRACKETS
8 8‐LN
12‐LN
16‐LN 6
1
1
1
4
4
4
SPRINGBOARD ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐016
7/16"‐14 X 1 3/4" GRADE 8
16
16
16
HTS‐16‐017
7/16" CAM LOCKS
16
16
16
HTS‐16‐018
5/16"‐18 X 1 1/2" GRADE 8
8
8
8
HTS‐16‐019
5/16" NYLOCKS 5/16 NYLOCKS
8
8
8
II‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER FLEX DRIVE ASSEMBLY ‐ COMMON PARTS FLEX DRIVE ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION S O
8 8‐LN
12‐LN
16‐LN 6
AK‐15‐FDS‐A001 FLEX DRIVE SHAFT ASSY
1
1
1
AK‐13‐CS‐A115
1
1
1
COLOR SORTER SHAKER DRIVE ASSY (SELL AS ONLY ASSY)
DRIVE MOUNT‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐020
7/16" x 1 1/2" SOCKET HEAD CAP SCREW
4
4
4
HTS‐16‐021
7/16" CAM LOCKS (2 PER)
4
4
4
II‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER FLEX DRIVE ASSEMBLY ‐ COMMON PARTS FLEX DRIVE ASSEMBLY ‐ COMMON PARTS
A
DRIVE SPRING BOARD ASSY (4 PER SET) W/ HARDWARE
AK‐13‐CS‐A116
B
FIBERBOARD ASSEMBLY (ONE FIBERBOARD) W/ BRACKETS
AK‐13‐CS‐A116A
II‐3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER FLEX DRIVE ASSEMBLY ‐ COMMON PARTS FLEX DRIVE ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
7/16" x 1 1/2" SOCKET HEAD CAP SCREW
HTS‐16‐020
B
7/16" CAM LOCKS (2 PER) / ( )
HTS‐16‐021 S 6 02
C
FLEX DRIVE SHAFT ASSY
AK‐15‐FDS‐A001
D
COLOR SORTER SHAKER DRIVE ASSY (SELL AS ONLY ASSY)
AK‐13‐CS‐A115
II‐4
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
E
E
1
D
D
5
C
C
A
7
6
4
2
B
B
A SECTION A-A SCALE 1 : 1.75
ITEM NO.
A
PART NUMBER
MATERIAL
REV A
1
AK-11-FDS-219
2
AK-11-FDS-SBO-021
AISI TGP 1045 ROUND BAR AISI TGP 1045 ROUND BAR
3
AK-11-FDS-SBO-022
4
AK-11-FDS-SBO-027
5
AK-11-FDS-SBO-A07
THICKNESS
DESCRIPTION
QTY.
16L FDS SPRING SHAFT
1
.060 OFFSET
4
A36 M/S ROUND BAR
BEARING OFFSET PIN
6
AISI TGP 1045 ROUND BAR Material <not specified>
.000 OFFSET
2
BEARING HOUSING ASSY
6
6
N-07
Material <not specified>
ADAPTER SLEEVE NUT
6
7
W-07
Material <not specified>
ADAPTER SLEEVE WASHER
6
8
7
6
5
PART NUMBER: AK-13-CS-A115 DESCRIPTION : COLOR SORTER SHAKER DRIVE ASSEMBLY
DEVELOPMENT COMPANY MATERIAL: SEE BOM
FOOD PROCESSING EQUIPMENT
THICKNESS:
FINISH: BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + OR - .030
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
3
MANUFACTURE & DESIGN
DATE: 6/29/2012
Drawn By: CRAIG PRESS BRAKE INFORMATION
.XXX = + OR - .010
410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:23.00 REVISION 1
A
Drawing Location: Y:\01-A&K Engineering Files\A&K Machinery\Color Sorter\
3
L ubrication TABLE 42a
Pre-Lubricated
Relubrication Amounts
Mariner bearing units come standard with an approximate 1/3rd grease fill. The bearings contain Mobil FM222 (NLGI #2, Aluminum Complex Food Grade Grease). Because the bearings come from the factory pre-lubricated, you should not add grease to the unit before placing into service.
Bearing Number
Relubrication Depending on the application, re-lubrication may be necessary to maximize bearing life. in these instances it is important to add only the amount of grease listed in Table 42a. The purpose of this relubrication is to ensure that your bearing is not running dry, but take care not to overfill your bearing. Ideally, a 1/3rd grease fill should be maintained.
Fill Amount oz.
204 205
0.05 0.06
206
0.10
207
0.15
208
0.15
209
0.20
210
0.25
211
0.35
212
0.45
See Table 42b for information on the frequency of relubrication intervals. Please note that relubricating a bearing may cause the operating temperature of the bearing to increase. This increase is temporary and the bearing should return to normal operating temperature after a short period of time.
Before Relubrication -Clean the grease fitting and surrounding area. -Clean nozzle or tip of greasing equipment -Ensure that the grease you intend to install is compatible with previously installed lubricant. -For best results, the bearing should be in rotation during relubrication.
Over Lubrication Warning Completely filling a bearing with grease may significantly decrease bearing life. Do not relubricate a bearing with more lubricant than listed in table 42a. Avoid the practice of pumping grease until you feel resistance, or until lubrication is emitted from bearing seals. TABLE 42b Relubrication Intervals
Environment
DN* Value
Clean
40,000 and below
Clean
40,000-70,000
Temperature (F°)
Interval
5-150°
6-12 months
150-210°
2-6 months
5-150°
2-6 months
150-210°
1 month
5-150°
1 week to 1 month
150-210°
1 day to 2 weeks
Dirty
Any DN
Very dirty
Any DN
Any temp.
1 day to 2 weeks
Exposed to water splashes
Any DN
Any temp.
daily
*DN = bore of the bearing (mm) x rpm
www.marinerbearings.com
HALF TRANSFER FIBER BOARD REPLACEMENT INSTRUCTIONS
Ensure 4 Hole Plates are on Bearing End
2 Hole Plates on Pan Mount End
5/16 Grade 8 Bolts Must be Tight
REMOVE (1) FIBER BOARD - REPLACE WITH NEW FIBER BOARD - DO THIS STEP 4 TIMES - REPLACE (1) FIBER BOARD AT A TIME 7/16 GRADE (8) BOLTS MUST BE TORQUED TO 60 FT/LBS WHEN REPLACING FIBER BOARDS, MUST REPLACE ALL (4) NOTE: IF ONE IS BAD ALL ARE BAD
HALF TRANSFER DRIVE REPLACEMENT INSTRUCTIONS
1. REMOVE PULLEY COVER - RECORD RPM
4. REMOVE DRIVE PULLEY
Drive Assembly
2. REMOVE DRIVE SPRING BOARDS
3. REMOVE DRIVE BELT
5. LOOSEN DRIVE MOUNT BOLTS 6. REMOVE DRIVE ASSEMBLY
7. INSTALL NEW DRIVE ASSEMBLY
8. INSTALL & TIGHTEN DRIVE MOUNT BOLTS DRIVE MOUNT BOLTS MUST BE TORQUED TO 65 ft/lbs
12. RE-INSTALL DRIVE SPRING BOARDS TIGHTEN BEARING BOLTS FIRST LINE UP PAN END OF FIBER BOARD WITH HOLES - IMPORTANT FIBER BOARD MUST BE IN A STRAIGHT LINE WITH PAN MOUNT
9. RE-INSTALL DRIVE PULLEY 10. ALIGN DRIVE PULLEY WITH MOTOR SHEAVE SO BELT WILL RUN STRAIGHT 13. RUN SHAKER TO ENSURE RPM IS THE SAME THEN INSTALL PULLEY COVER
11. RE-INSTALL DRIVE BELT
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER ARM & ARM MOUNT ASSEMBLY ‐ COMMON PARTS SHAKER ARM & ARM MOUNT ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
8 8‐LN
12‐LN
16‐LN 6
LARGE SHAKER ARM ASSY W/SPRINGS & HARDWARE (#FS250‐00)
12
12
12
LARGE SHAKER ARM (SHAKER ARM ONLY W/BUSHINGS)
12
12
12
313
LOWER SPRING ‐ HEAVY
12
12
12
314
UPPER SPRING, LIGHT
12
12
12
335
BUSHING, LARGE SHAKER ARM (#FS250‐03)
24
24
24
12
12
12
305 FS‐250‐01
ITEM DESCRIPTION S O
AK‐11‐FDS‐131 SHAKER SPRING LOWER MOUNT
SHAKER ARM & ARM MOUNT ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
HTS‐16‐022
305B
8‐LN
12‐LN
16‐LN
/ / 7/16"‐14 X 1/2" SOCKET HEAD CAP SCREW
24
24
24
HARDWARE FOR LARGE SHAKER ARM (INCLUDES: (1) 3/8" X 5 1/2" HEX BOLT, (1) 3/8"‐16 NYLOCK HEX NUT, (2) 3/4"‐10 X 4" HEX BOLTS, (2) 3/4" LOCK WASHERS, (2) 3/4"‐10 FULL HEX NUTS, (2) 3/8"‐16 X 1 1/2" HEX BOLTS, (2) 3/8" FLAT WASHERS, (2) 3/8"‐16 NYLOCK HEX NUTS
12
12
12
III‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER ARM & ARM MOUNT ASSEMBLY ‐ COMMON PARTS SHAKER ARM & ARM MOUNT ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # 305
A
LARGE SHAKER ARM ASSY W/SPRINGS & HARDWARE (#FS250‐00)
B
LARGE SHAKER ARM (SHAKER ARM ONLY W/BUSHINGS) ( / )
C
LOWER SPRING ‐ HEAVY
313
D
UPPER SPRING, LIGHT
314
E
BUSHING, LARGE SHAKER ARM (#FS250‐03)
335
F
SHAKER SPRING LOWER MOUNT
FS 250 01 FS‐250‐01
AK‐11‐FDS‐131
III‐2
8
7
6
4
5
1
2
3
REVISIONS ZONE
F
REV.
DESCRIPTION
DATE
APPROVED
1
E
E
D
D
6
4 5
C
C
7
2
9
ITEM NO. 1 2 3 4 5 6 7 8 9
8
B
PART NUMBER FS250-01 FS250-04 FS250-06 FS250-07 FS250-05 38550 38FLAT 38LOCK 094-PIN
DESCRIPTION SPRING ARM ASSEMBLY LOWER SPRING-SHAKER ARM GUIDE-LOWER SPRING CAP-UPPER SPRING UPPER SPRING-SHAKER ARM 3/8-16NC X 5 1/2 HEX HEAD CAP SCREW 3/8 DIAMETER SAE FLAT WSHER 3/8-16NC LOCK NUT
QTY. 1 1 1 1 1 1 1 1 2
B
CUSTOMER : PART NUMBER: FS250-00 DESCRIPTION : SPRING ARM ASSEMBLY A
A
THICKNESS:
MATERIAL: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
DATE: 12/26/1998
Drawn By:
FINISH:
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + OR - .030
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
3
.XXX = + OR - .010
THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:2 SHEET 1 OF 1
WEIGHT: REVISION 1
Drawing Location: O:\GRADERS\FS\SPRING ARM\
3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION S O
AK‐12‐FDS‐DB‐013 SPRING CAPTURE (HORIZONTAL ASSY)
8 8‐LN
12‐LN
16‐LN 6
4
4
4
AK‐13‐FDS‐121
SPRING PLATE
4
4
4
AK‐12‐FDS‐031
SPRING MOUNT PLATE
2
2
2
AK‐15‐FDS‐042
SPRING MOUNT
2
2
2
HORIZONTAL SPRING MOUNT ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐023
3/4" X 5" HEX HEAD BOLT GRADE 8
4
4
4
HTS‐16‐024
3/4" JAM NUT
4
4
4
IV‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
4
4
4
4
4
4
ORANGE SPRING, VERTICAL SPRING ASSY
4
4
4
AK 12 FDS DB 013 SPRING AK‐12‐FDS‐DB‐013 SPRING CAPTURE, VERTICAL SPRING ASSY CAPTURE VERTICAL SPRING ASSY
4
4
4
AK‐13‐FDS‐A034 SUB FRAME SPRING MOUNT, VERTICAL SPRING ASSY AK‐12‐FDS‐DB‐012 RAIL GUIDE, VERTICAL SPRING ASSY LHL 1000D 01
VERTICAL SPRING VERTICAL ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐025
1/2"‐13 X 3 1/2" HEX HEAD BOLT GRADE 8
4
4
4
HTS‐16‐026
1/2+‐13 JAM NUT
4
4
4
IV‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # AK‐12‐FDS‐DB‐013
A
SPRING CAPTURE (HORIZONTAL ASSY)
B
3/4" 3/4" X 5" HEX HEAD BOLT GRADE 8 X 5" HEX HEAD BOLT GRADE 8
HTS 16 023 HTS‐16‐023
C
3/4" JAM NUT
HTS‐16‐024
IV‐3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
SPRING PLATE
AK‐13‐FDS‐121
B
SPRING MOUNT PLATE
AK‐12‐FDS‐031 2 S 03
C
SPRING MOUNT
AK‐15‐FDS‐042
IV‐4
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS SPRING MOUNT ASSEMBLIES ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # AK‐13‐FDS‐A034
A
SUB FRAME SPRING MOUNT, VERTICAL SPRING ASSY
B
RAIL RAIL GUIDE, VERTICAL SPRING ASSY GUIDE VERTICAL SPRING ASSY
C
ORANGE SPRING, VERTICAL SPRING ASSY
LHL 1000D 01
D
1/2"‐13 X 3 1/2" HEX HEAD BOLT GRADE 8
HTS‐16‐025
E
1/2+‐13 JAM NUT
HTS‐16‐026
F
SPRING CAPTURE, VERTICAL SPRING ASSY
AK 12 FDS DB 012 AK‐12‐FDS‐DB‐012
AK‐12‐FDS‐DB‐013
IV‐5
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐005
LINEAR ACTUATOR (#CC58HD/E/101/AA36/S)
1
1
1
HTS‐16‐027
CONTROL BOX, LINEAR ACTUATOR
1
1
1
2
2
2
AK‐15‐FDS‐DB‐016 MOUNTS, LINEAR ACTUATOR
LINEAR ACTUATOR ASSEMBLY ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐027
1/2" NYLOCK NUT
1
1
1
HTS‐16‐028
1/2" FLAT WASHER
1
1
1
HTS‐16‐029
1/2"‐13 X 12" GRADE 5 HEX HEAD BOLT
1
1
1
V‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS
LETTER A
ITEM DESCRIPTION LINEAR ACTUATOR (#CC58HD/E/101/AA36/S)
PART # HTS‐16‐005
V‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS
LETTER A
ITEM DESCRIPTION CONTROL BOX, LINEAR ACTUATOR
PART # HTS‐16‐027
V‐3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS LINEAR ACTUATOR ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # AK‐15‐FDS‐DB‐016
A
MOUNTS, LINEAR ACTUATOR
B
1/2" 1/2" NYLOCK NUT NYLOCK NUT
HTS 16 038 HTS‐16‐038
C
1/2" FLAT WASHER
HTS‐16‐028
D
1/2"‐13 X 12" GRADE 5 HEX HEAD BOLT
HTS‐16‐029
V‐4
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
AK‐11‐FDS‐A052
INFEED PAN WELDMENT ASSY, 8‐LANE
1
0
0
AK‐15‐FDS‐A007
DISCHARGE PAN WELDMENT ASSY, 8‐LANE
1
0
0
AK‐11‐FDS‐A051
DISCHARGE PAN WELDMENT ASSY, 8‐LANE (SEED SAVER)
1
0
0
AK‐15‐FDS‐A004
INFEED PAN WELDMENT ASSY, 12‐LANE
0
1
0
AK‐11‐FDS‐A046
DISCHARGE PAN WELDMENT ASSY, 12‐LANE
0
1
0
AK‐15‐FDS‐A003
DISCHARGE PAN WELDMENT ASSY, 12‐LANE (SEED SAVER)
0
1
0
AK‐11‐FDS‐DB‐A02 INFEED PAN WELDMENT 16‐LANE
0
0
1
AK‐11‐FDS‐DB‐A03 DISCHARGE PAN WELDMENT 16‐LANE
0
0
1
AK‐11‐FDS‐A010
INFEED PAN WELDMENT, 16‐LANE SEED SAVER
0
0
1
AK‐11‐FDS‐A014
DISCHARGE PAN WELDMENT, 16‐LANE SEED SAVER
0
0
1
AK‐11‐FDS‐267
SIDE SUPPORT DISCHARGE (DISCH. PAN WELDMENT)
2
2
2
VI‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
AK‐12‐FDS‐DB‐004 CORN COVER BRACKET, 16‐LANE SPLIT PAN
2
2
2
AK‐12‐FDS‐DB‐005 CORN COVER (#100 BLACK BELTING), 16‐LANE SPLIT PAN
1
1
1
AK‐12‐FDS‐DB‐032 CORN COVER BACKING BAR, 16‐LANE SPLIT PAN
2
2
2
AK‐11‐FDS‐DB‐078 8/16‐LANE SEED SAVER BELT, BLACK W/GUIDES / /
1
0
2
AK‐11‐FDS‐DB‐083 8/16‐LANE SEED SAVER BELT, BLACK RH SLOT
1
0
2
AK‐11‐FDS‐DB‐087 8/16‐LANE SEED SAVER BELT, BLACK LH SLOT
1
0
2
AK‐11‐FDS‐DB‐075 STRAP, 8/16‐LANE SEED SAVER BELT
1
0
2
AK‐12‐FDS‐024
STRAP, 12‐LANE SEED SAVER BELT
0
1
0
AK‐12‐FDS‐022
12‐LANE SEED SAVER BELT (FOUR GUIDES)
1
1
1
AK‐12‐FDS‐023
12‐LANE SEED SAVER BELT (FOUR GUIDES)
1
1
1
SEED SAVER BELTS & CORN COVERS ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
AK‐12‐FDS‐DB‐004 CORN COVER BRACKET, 16‐LANE SPLIT PAN
7
9
14
AK‐12‐FDS‐DB‐005 CORN COVER (#100 BLACK BELTING), 16‐LANE SPLIT PAN
7
9
14
AK‐12‐FDS‐DB‐032 CORN COVER BACKING BAR, 16‐LANE SPLIT PAN CORN COVER BACKING BAR, 16‐LANE SPLIT PAN
12
12
12
AK‐11‐FDS‐DB‐078 8/16‐LANE SEED SAVER BELT, BLACK W/GUIDES
12
12
12
VI‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
AK‐11‐FDS‐DB‐054 SAFETY RAILS (YELLOW)
8‐LN
12‐LN
16‐LN
2
2
2
AK‐15‐FDS‐011
FRONT SLIDE, WHEEL (BRASS)
2
2
2
AK‐12‐FDS‐032
REAR SLIDE, WHEEL (BRASS)
2
2
2
VI‐3
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
CORN COVER BRACKET, 16‐LANE SPLIT PAN
AK‐12‐FDS‐DB‐004
B
CORN CORN COVER (#100 BLACK BELTING), 16‐LANE SPLIT PAN COVER (#100 BLACK BELTING) 16 LANE SPLIT PAN
AK 12 FDS DB 005 AK‐12‐FDS‐DB‐005
C
CORN COVER BACKING BAR, 16‐LANE SPLIT PAN
AK‐12‐FDS‐DB‐032
D
1/4"‐20 X 3/4" BUTTON HEAD CAP SCREW
HTS‐16‐032
E
1/4"‐20 LOCK WASHER
HTS‐16‐033
VI‐4
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
8/16‐LANE SEED SAVER BELT, BLACK W/GUIDES
AK‐11‐FDS‐DB‐078
B
8/16 8/16‐LANE SEED SAVER BELT, BLACK RH SLOT LANE SEED SAVER BELT BLACK RH SLOT
AK 11 FDS DB 083 AK‐11‐FDS‐DB‐083
C
8/16‐LANE SEED SAVER BELT, BLACK LH SLOT
AK‐11‐FDS‐DB‐087
D
STRAP, 8/16‐LANE SEED SAVER BELT
AK‐11‐FDS‐DB‐075
E
STRAP, 12‐LANE SEED SAVER BELT
AK‐12‐FDS‐024
F
12‐LANE SEED SAVER BELT (FOUR GUIDES)
AK‐12‐FDS‐022
G
12‐LANE SEED SAVER BELT (FOUR GUIDES)
AK‐12‐FDS‐023
VI‐5
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER PAN ASSEMBLY ‐ COMMON PARTS SHAKER PAN ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART # AK‐11‐FDS‐DB‐054
A
SAFETY RAILS (YELLOW)
B
FRONT FRONT SLIDE, WHEEL (BRASS) SLIDE WHEEL (BRASS)
AK 15 FDS 011 AK‐15‐FDS‐011
C
REAR SLIDE, WHEEL (BRASS)
AK‐12‐FDS‐032
VI‐6
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
A
NEW DOG BONE BRACKET
3/10/2015
MILES
B
REMOVED SOME PARTS
5/27/2015
MILES
E
E
D
D
C
C
B
B
A
ITEM NO.
PART NUMBER
MATERIAL
THICKNESS
DESCRIPTION
1
AK-11-FDS-263
ASTM A36 Steel
.187
SIDE SUPPORT 12L PAN 1/2 T
2
2
AK-11-FDS-270
A36 M/S RECT BAR
1.50
SPRING MOUNT
1
REV
QTY.
PART NUMBER: AK-11-FDS-A052 DESCRIPTION: INFEEDPANWELDMENT 8L
3
AK-11-FDS-271
ASTM A572 GRADE 50
.750
SPRING MOUNT PLATE
1
4
AK-11-FDS-300
ASTM A36 Steel
.105
FLEX DRIVE 8L PAN 1/2 T
1
5
AK-11-FDS-301
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
3
6
AK-11-FDS-DB-088
ASTM A36 Steel
.250
SIDE SUPPORT 12L PANE 1/2 T
2
MATERIAL: Material <not specified>
.187
SPRING BRACKET
1
FINISH: BENGAL SILVER
SPRING MOUNT
2
7
AK-12-FDS-DB-015
ASTM A36 Steel
8
AK-12-FDS-DB-016
A36 M/S ROUND BAR
9
AK-12-FDS-DB-019
ASTM A36 Steel
.187
SPRING BRACKET (LEFT)
1
10
AK-15-FDS-026
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
6
8
7
A
6
5
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 12/29/2010
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:296.047 REVISION B 1
SCALE: 1:8 SHEET 1 OF 2
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
F
8
7
6
4
5
1
2
3
REVISIONS ZONE
2
REV.
DESCRIPTION
DATE
APPROVED
A
REMOVED & ADDED PARTS
5/27/2015
MILES
F
6
E
E
A
5.687
14
D
D
12
A
41.00
17
10 8 3
C
C
14.750
16
8
7
B
A
5.811
ITEM NO.
PART NUMBER
MATERIAL
THICKNESS
DESCRIPTION
1
AK-09-FDS-126
ASTM A36 Steel
REV
.250
PIVOT MOUNT
QTY. 2
2
AK-11-FDS-069
ASTM A36 Steel
.375
PIVOT ARM
2
3
AK-11-FDS-127
A36 M/S ROUND BAR
FILLER
4
4
AK-11-FDS-133
ASTM A36 Steel
.105
8L PAN 1/2 T
1
5
AK-11-FDS-218
ASTM A572 GRADE 50
.750
SPRING MOUNT
2
6
AK-11-FDS-267
ASTM A36 Steel
.187
SIDE SUPPORT DISCHARGE
2
7
AK-11-FDS-296
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
8
AK-11-FDS-297
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
9
AK-11-FDS-298
ASTM A36 Steel
.312
CROSS BRACE
1
10
AK-11-FDS-DB-002
A36 M/S RECT BAR
2X6
SPRING MOUNT GUSSET
2 1
B
5
PART NUMBER: AK-15-FDS-A007 DESCRIPTION: DISCHARGE PANWELDMENT 8L
11
AK-11-FDS-DB-058
ASTM A36 Steel
.375
LATCH PLATE
12
AK-11-FDS-DB-059
ASTM A36 Steel
.250
LATCH PLATE
1
13
AK-12-FDS-DB-016
A36 M/S ROUND BAR
SPRING MOUNT
2
14
AK-15-FDS-025
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
4
MATERIAL: Material <not specified> FINISH: BENGAL SILVER
A
15
AK-15-FDS-027
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
1
16
AK-15-FDS-028
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB ( LEFT )
1
17
FS-220-105
ASTM A36 Steel
.187
SHAKER PAN LIP
1
18
AK-12-FDS-029
ASTM A36 Steel
.187
SPRING BRACKET
2
8
7
6
5
DETAIL A SCALE 1 : 4
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:200.260 REVISION A 1
SCALE: 1:8 SHEET 1 OF 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
15
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
A
NEW CHUTE & DOG BONE BRACKETS
3/10/2015
MILES
E
E
D
D
C
C
B
A
ITEM NO.
PART NUMBER
MATERIAL
1
AK-09-FDS-126
ASTM A36 Steel
2
AK-11-FDS-037
ASTM A36 Steel
3
AK-11-FDS-069
ASTM A36 Steel
4
AK-11-FDS-127
A36 M/S ROUND BAR
REV A
THICKNESS
DESCRIPTION
.250
PIVOT MOUNT
QTY. 2
.105
SEED SAVER 8L PAN 1/2 T SEED SAVER
1
.375
PIVOT ARM
2
FILLER
4
5
AK-11-FDS-218
ASTM A572 GRADE 50
.750
SPRING MOUNT
2
6
AK-11-FDS-267
ASTM A36 Steel
.187
SIDE SUPPORT DISCHARGE
2
7
AK-11-FDS-296
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
8
AK-11-FDS-297
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
9
AK-11-FDS-298
ASTM A36 Steel
.312
CROSS BRACE
1 2
10
AK-11-FDS-DB-002
A36 M/S RECT BAR
2X6
SPRING MOUNT GUSSET
11
AK-11-FDS-DB-058
ASTM A36 Steel
.375
LATCH PLATE
1
12
AK-11-FDS-DB-059
ASTM A36 Steel
.250
LATCH PLATE
1
13
AK-13-FDS-108
SEE BOM
BACK PLATE
1
14
AK-13-FDS-109
SEE BOM
FRONT PLATE
1
B
PART NUMBER: AK-11-FDS-A051 DESCRIPTION: DISCHARGE PANWELDMENT 8L
15
FS-220-105
ASTM A36 Steel
.187
SHAKER PAN LIP
1
16
AK-13-FDS-130
A36 M/S RECT TUBE
2 X 3 X .250
SPRING SUPPORT TUBE
4
17
AK-13-FDS-133
ASTM A36 Steel
.500
SPRING PLATE
4
18
AK-12-FDS-DB-016
A36 M/S ROUND BAR
A
SPRING MOUNT
4
MATERIAL: Material <not specified>
19
AK-11-FDS-DB-080
ASTM A36 Steel
A
.120
CHUTE
2
FINISH: BENGAL SILVER
20
AK-15-FDS-025
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
4
21
AK-15-FDS-027
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
1
22
AK-15-FDS-028
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB ( LEFT )
1
8
7
6
5
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:228.614 REVISION A 1
SCALE: 1:8 SHEET 1 OF 2
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
F
8
7
6
4
5
B
6
1
2
3
REVISIONS
SECTION B-B
ZONE
REV.
DESCRIPTION
DATE
APPROVED
A
NEW DOG BONE CAPTURES
4/7/2015
MILES
F
C
E
E
13
B
D
D
7
17
62.625 I.D
A
5.687
20.000
9
DETAIL D SCALE 1 : 6
C
C
5.811
A 4
DETAIL C SCALE 1 : 6
14.750
6.236
D
10
12 11
B
A
25.907
25.907
B
A 15
8
.579
16
8.311
5 3
A
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
PART NUMBER AK-09-FDS-126 AK-11-FDS-069 AK-11-FDS-127 AK-11-FDS-218 AK-11-FDS-265 AK-11-FDS-266 AK-11-FDS-267 AK-11-FDS-273 AK-11-FDS-282 AK-11-FDS-DB-002 AK-11-FDS-DB-058 AK-11-FDS-DB-059 FS-220-106 AK-12-FDS-029 AK-15-FDS-025 AK-15-FDS-028 AK-15-FDS-027 8
MATERIAL ASTM A36 Steel ASTM A36 Steel A36 M/S ROUND BAR ASTM A572 GRADE 50 ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel A36 M/S RECT TUBE A36 M/S RECT TUBE A36 M/S RECT BAR ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel 7
REV
THICKNESS .250 .375
DESCRIPTION PIVOT MOUNT PIVOT ARM FILLER SPRING MOUNT CROSS BRACE 12L PAN 1/2 T SIDE SUPPORT DISCHARGE PAN SUPPORT TUBE PAN SUPPORT TUBE SPRING MOUNT GUSSET LATCH PLATE LATCH PLATE 12L SHAKER PAN LIP SPRING BRACKET DOG BONE SUPPORT TAB DOG BONE SUPPORT TAB ( LEFT ) DOG BONE SUPPORT TAB
.750 .312 .105 .187 2 X 3 X .250 2 X 3 X .250 2X6 .375 .250 .187 .187 .120 .120 .120 6
QTY. 2 2 4 2 1 1 2 1 1 2 2 2 1 2 4 1 1 5
DETAIL A SCALE 1 : 6
PART NUMBER: AK-11-FDS-A046 DESCRIPTION: DISCHARGE PANWELDMENT 12L DEVELOPMENT COMPANY MATERIAL: Material <not specified>
THICKNESS:
DrawnBy: CRAIG
FINISH: BENGAL SILVER PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:260.940 REVISION A 1
SCALE: 1:12 SHEET 1 OF 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
1 2
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
D
D
8
9
C
C
7 1 5
4
10
B
3
A
ITEM NO.
PART NUMBER
MATERIAL
THICKNESS
DESCRIPTION
1
AK-11-FDS-259
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
3
2
AK-11-FDS-270
A36 M/S RECT BAR
1.50
SPRING MOUNT
1
REV
QTY.
3
AK-11-FDS-271
ASTM A572 GRADE 50
.750
SPRING MOUNT PLATE
1
4
AK-12-FDS-DB-015
ASTM A36 Steel
.187
SPRING BRACKET
1
5
AK-12-FDS-DB-016
A36 M/S ROUND BAR
6
AK-12-FDS-DB-019
ASTM A36 Steel
7
AK-15-FDS-026
ASTM A36 Steel
.120
8
AK-15-FDS-045
ASTM A36 Steel
.105
A .187
1
MATERIAL: Material <not specified>
DOG BONE SUPPORT TAB
6
FINISH: BENGAL SILVER
2015 FLEX DRIVE 12L PAN 1/2 T
1
AK-15-FDS-046
ASTM A36 Steel
.187
2015 SIDE SUPPORT 12L PAN 1/2 T
2
AK-15-FDS-047
ASTM A36 Steel
.250
2015 SIDE SUPPORT 12L PANE 1/2 T
2
7
6
DEVELOPMENT COMPANY
2
SPRING BRACKET (LEFT)
9 8
PART NUMBER: AK-15-FDS-A004 DESCRIPTION: 2015 INFEEDPANWELDMENT 12L
SPRING MOUNT
10
5
B
2
THICKNESS:
DrawnBy: CRAIG
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 12/29/2010
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:368.620 REVISION 1
SCALE: 1:8 SHEET 1 OF 2
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
E
E
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
D
D
13
C
B
A
C
ITEM NO.
PART NUMBER
MATERIAL
THICKNESS
DESCRIPTION
1
AK-09-FDS-126
ASTM A36 Steel
REV
.250
PIVOT MOUNT
QTY. 2
2
AK-11-FDS-069
ASTM A36 Steel
.375
PIVOT ARM
2
3
AK-11-FDS-127
A36 M/S ROUND BAR
FILLER
4
4
AK-11-FDS-218
ASTM A572 GRADE 50
.750
SPRING MOUNT
2
5
AK-11-FDS-265
ASTM A36 Steel
.312
CROSS BRACE
1
6
AK-11-FDS-267
ASTM A36 Steel
.187
SIDE SUPPORT DISCHARGE
2
7
AK-11-FDS-273
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
8
AK-11-FDS-282
A36 M/S RECT TUBE
2 X 3 X .250
PAN SUPPORT TUBE
1
9
AK-11-FDS-DB-002
A36 M/S RECT BAR
2X6
SPRING MOUNT GUSSET
2
10
AK-11-FDS-DB-058
ASTM A36 Steel
.375
LATCH PLATE
2
11
AK-11-FDS-DB-059
ASTM A36 Steel
.250
LATCH PLATE
2
12
AK-11-FDS-DB-080
ASTM A36 Steel
.120
CHUTE
2
13
AK-12-FDS-019
ASTM A36 Steel
.105
12L PAN 1/2 T (SEED SAVER)
1
14
AK-12-FDS-024
ASTM A36 Steel
15
AK-12-FDS-025
ASTM A36 Steel
16
AK-12-FDS-026
ASTM A36 Steel
17
AK-12-FDS-029
ASTM A36 Steel
18
AK-15-FDS-025
19
AK-15-FDS-027
20 21 8
A
3 B
PART NUMBER: AK-15-FDS-A003 DESCRIPTION: 2015 DISCHARGE PANWELDMENT 12L
.120
STRAP
2
.120
FRONT PLATE
1
.120
BACK PLATE
1
.187
SPRING BRACKET
2
MATERIAL: Material <not specified>
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
4
FINISH: BENGAL SILVER
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB
1
AK-15-FDS-028
ASTM A36 Steel
.120
DOG BONE SUPPORT TAB ( LEFT )
1
FS-220-106
ASTM A36 Steel
.187
12L SHAKER PAN LIP
1
7
A
6
5
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:280.557 REVISION 1
SCALE: 1:8 SHEET 1 OF 2
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
E
E
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
A
CHANGES
8/20/2013
RON A
B
NEW DOG BONE CAPTURES
4/7/2015
MILES
E
E
4 8
7 D
D
B
3 C
C
1
B
A
B
ITEM NO.
PART NUMBER
MATERIAL
REV
THICKNESS
DESCRIPTION
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
AK-11-FDS-032 AK-11-FDS-DB-001 AK-11-FDS-DB-015 AK-11-FDS-DB-016 AK-11-FDS-DB-017 AK-11-FDS-DB-026 AK-11-FDS-DB-027 AK-11-FDS-DB-034 AK-11-FDS-DB-035 AK-11-FDS-DB-046 AK-11-FDS-DB-047 AK-11-FDS-DB-048 AK-11-FDS-DB-096 AK-12-FDS-DB-015 AK-12-FDS-DB-016 AK-12-FDS-DB-019 AK-12-FDS-DB-024 AK-15-FDS-026
A36 M/S RECT TUBE ASTM A572 GRADE 50 ASTM A36 Steel ASTM A36 Steel ASTM A572 GRADE 50 ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel A36 M/S ROUND BAR ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel
C
2 X 3 X .120 .750 .187 .187 .750 .105 .187 .187 .250 .375 .375 .375 .187 .187
PAN SUPPORT TUBE SPRING MOUNT SIDE SUPPORT 8L PAN 1/2 T SIDE SUPPORT INNER 8L PANE 1/2 T SPRING MOUNT FLEX DRIVE 8L PAN 1/2 T SIDE SUPPORT 8L PANE 1/2 T SIDE SUPPORT 8L PANE 1/2 T SPRING BRACKET SPACER PAN GUSSET PAN GUSSET PAN GUSSET PAN SUPPORT SPRING BRACKET SPRING MOUNT SPRING BRACKET (LEFT) PAN STIFFENER DOG BONE SUPPORT TAB
3 2 2 2 1 2 2 2 2 1 1 1 1 1 2 1 1 6
8
7
A A
A A A
A A
.187 .250 .120 6
5
PART NUMBER: AK-11-FDS-DB-A02 DESCRIPTION: INFEEDPANWELDMENT 16L DEVELOPMENT COMPANY MATERIAL: Material <not specified>
THICKNESS:
DrawnBy: CRAIG
FINISH: BENGAL SILVER PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 12/29/2010
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:543.271 REVISION B 1
SCALE: 1:16 SHEET 1 OF 2
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS ZONE
.375
DESCRIPTION
DATE
APPROVED
B
ADDED SEED SAVER PAN
1/22/2014
CRAIG S
A
17.375
15 F
REV.
B
16
A
6.0
SECTION A-A SCALE 1 : 10
19
86.75
F
E
23
E
DETAIL G SCALE 1 : 5
19.313 40.625
D
13
DETAIL B SCALE 1 : 5
27
24
D
D
27
D
B
10.811
21
27
27
14.750
G 5 SECTION F-F SCALE 1 : 10
19
C
B
A
ITEM NO.
PART NUMBER
MATERIAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
AK-09-FDS-126 AK-11-FDS-032 AK-11-FDS-040 AK-11-FDS-069 AK-11-FDS-126 AK-11-FDS-127 AK-11-FDS-037 AK-11-FDS-218 AK-11-FDS-DB-002 AK-11-FDS-DB-018 AK-11-FDS-DB-043 AK-11-FDS-DB-044 AK-11-FDS-DB-049 AK-11-FDS-DB-055 AK-11-FDS-DB-058 AK-11-FDS-DB-059 AK-12-FDS-DB-008 AK-12-FDS-DB-025 AK-12-FDS-DB-026 FS-220-105 AK-11-FDS-DB-079 AK-11-FDS-DB-082 AK-11-FDS-DB-076 AK-11-FDS-DB-080 AK-14-FDS-029 AK-14-FDS-030 AK-15-FDS-025 AK-15-FDS-027 AK-15-FDS-028 AK-15-S-005 AK-15-S-006 AK-16-FDS-021
ASTM A36 Steel A36 M/S RECT TUBE ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel A36 M/S ROUND BAR ASTM A36 Steel ASTM A572 GRADE 50 A36 M/S RECT BAR ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel SEE BOM ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel ASTM A36 Steel
8
7
REV D
A
A
THICKNESS
DESCRIPTION
QTY.
.250 2 X 3 X .120 .187 .375 .312
PIVOT MOUNT PAN SUPPORT TUBE SIDE SUPPORT INNER DISCHARGE PIVOT ARM CROSS BRACE FILLER SEED SAVER 8L PAN 1/2 T SEED SAVER SPRING MOUNT SPRING MOUNT GUSSET SIDE SUPPORT DISCHARGE PAN GUSSET PAN GUSSET PAN GUSSET SNOUT GUSSET LATCH PLATE LATCH PLATE PAN SUPPORT CHANNELL PAN STIFFENER PAN STIFFENER SHAKER PAN LIP BACK PLATE BACK PLATE (LEFT) SEED SAVER ANGLE PLATE CHUTE TOP COVER ( SEED SAVER ) LOWER COVER ( SEED SAVER ) DOG BONE SUPPORT TAB DOG BONE SUPPORT TAB DOG BONE SUPPORT TAB ( LEFT ) SEED SAVER COVER ANGLE SEED SAVER COVER ANGLE ( LEFT ) PAN SUPPORT CHANNEL
4 2 2 4 1 6 2 2 2 2 1 1 1 1 2 2 1 2 1 2 1 1 2 4 1 2 4 1 1 2 2 2
.105 .750 2X6 .187 .375 .375 .375 .375 .375 .250 .187 .250 .250 .187 .120 .120 .120 .120 .062 .062 .120 .120 .120 .105 .105 .105 6
5
C
6.579
28 8
7
F
29
37.782
37.782
5.811 8.311 SECTION D-D SCALE 1 : 10
E
B
18
PART NUMBER: AK-11-FDS-DB-A03 DESCRIPTION: DISCHARGE PANWELDMENT 16L DEVELOPMENT COMPANY MATERIAL: Material <not specified>
THICKNESS:
DrawnBy: CRAIG
FINISH: BENGAL SILVER PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:467.769 REVISION B 1
SCALE: 1:8 SHEET 1 OF 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
DETAIL E SCALE 1 : 5
8
7
6
4
5
1
2
3
R E V IS IO N S ZO N E
REV.
D E S C R IP TIO N
D ATE
APPRO V ED
F
E
E
D
D
2
C
C
5
B
B
ITE M N O .
A
PART N UM BER
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19
A K -1 1 -F D S -0 3 0 A K -1 1 -F D S -0 3 1 A K -1 1 -F D S -0 3 2 A K -1 1 -F D S -0 3 3 A K -1 1 -F D S -0 3 4 A K -1 1 -F D S -0 3 5 A K -1 1 -F D S -0 3 6 A K -1 1 -F D S -0 4 1 A K -1 1 -F D S -0 4 2 A K -1 1 -F D S -1 2 8 A K -1 1 -F D S -1 6 7 A K -1 1 -F D S -1 6 9 A K -1 1 -F D S -1 7 0 A K -1 1 -F D S -1 7 1 A K -1 1 -F D S -1 7 2 A K -1 1 -F D S -1 7 3 A K -1 1 -F D S -1 7 5 A K -1 1 -F D S -1 8 5 8
M A TE R IA L
REV
A S T M A 3 6 S te e l A A S T M A 3 6 S te e l A A 3 6 M /S R E C T TU B E A A S T M A 3 6 S te e l A A S T M A 3 6 S te e l A A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l M / S 2 .0 " S C H E D U L E 8 0 A S T M A 3 6 S te e l A S TM A 5 7 2 G R A D E 5 0 A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l M /S 1 1/2" SC H E D U LE 80 7
TH IC K N E S S
D E S C R IP T IO N
.1 0 5 .1 8 7 2 X 3 X .1 2 0 .1 8 7 .1 8 7 .1 0 5 .1 0 5 .1 0 5 .1 0 5 .1 8 7
Q TY .
F L E X D R IV E 8 L P A N 1 / 2 T 2 S ID E S U P P O R T 8 L P A N 1 / 2 T 2 P A N S U P P O R T TU B E 3 IN N E R TU B E S U P P O R T 6 S I D E S U P P O R T I N N E R 8 L P A N E 1 /22 T D O G B O N E SU P P O R T TA B 2 D O G B O N E SU P P O R T TA B 2 D O G B O N E SU P P O R T TA B 1 D O G B O N E SU P P O R T TA B 1 S ID E S U P P O R T 8 L P A N E 1 / 2 T 4 IN F E E D P A N A R M O U TE R 1 IN F E E D A R M F LA T B A R IN N E R 1 MATERIAL: Material <not specified> IN F E E D A R M S P R IN G M O U N T 5 FINISH: BENGAL SILVER IN F E E D A R M E N D C A P 1 IN F E E D A R M E N D P L A TE 1 PRESS BRAKE INFORMATION IN F E E D A R M G U S S E T 1 BEND DEDUCTION IN F E E D A R M S U P P O R T 1 PRESS BRAKE V DIE PRESS BRAKE PUNCH IN F E E D P A N A R M IN N E R 1
PART NUMBER: AK-11-FDS-A010 DESCRIPTION: INFEEDPANWELDMENT 16L
.5 0 .7 5 0 .2 5 0 .2 5 0 .5 0 .1 8 7 6
5
4
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
FOOD PROCESSING EQUIPMENT
DATE: 12/29/2010
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:16 SHEET 1 OF 2
WEIGHT:731.151 REVISION A 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
1
8
7
6
5
4
1
2
3
R E V IS IO N S ZO N E
REV.
D E S C R IP TIO N
D ATE
APPRO V ED
F
E
E
4
D
D
C
C
B
B
A
ITE M N O . 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16
PART N UM BER A K -0 9 -F D S -1 2 6 A K -1 1 -F D S -0 3 2 A K -1 1 -F D S -0 3 3 A K -1 1 -F D S -0 3 7 A K -1 1 -F D S -0 3 9 A K -1 1 -F D S -0 4 0 A K -1 1 -F D S -0 6 6 A K -1 1 -F D S -0 6 7 A K -1 1 -F D S -0 6 9 A K -1 1 -F D S -1 2 6 A K -1 1 -F D S -1 2 7 A K -1 1 -F D S -1 5 7 A K -1 1 -F D S -1 5 8 A K -1 1 -F D S -1 7 6 F S-2 2 0 -1 0 5 8
M A TE R IA L REV A S T M A 3 6 S te e l A 3 6 M /S R E C T TU B E A A S T M A 3 6 S te e l A A S T M A 3 6 S te e l A A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A S T M A 3 6 S te e l A 36 M /S R O U N D BA R A S TM A 5 7 2 G R A D E 5 0 A S T M A 3 6 S te e l M /S 3/4" SC H ED U LE 80 7
TH IC K N E S S .2 5 0 2 X 3 X .1 2 0 .1 8 7 .1 0 5 .1 8 7 .1 8 7 .1 0 5 .1 0 5 .3 7 5 .3 1 2
D E S C R IP T IO N Q TY . P IV O T M O U N T 4 P A N S U P P O R T TU B E 2 IN N E R TU B E S U P P O R T 4 S E E D S A V E R 8 L P A N 1 / 2 T S E E D S A2V E R S ID E S U P P O R T D IS C H A R G E 2 S I D E S U P P O R T I N N E R D I S C H A R G2E D O G B O N E SU P P O R T TA B 3 D O G B O N E SU P P O R T TA B 3 P IV O T A R M 4 MATERIAL: Material <not specified> C RO SS BRAC E 1 FINISH: BENGAL SILVER F IL L E R 6 S P R IN G M O U N T 2 PRESS BRAKE INFORMATION SP R IN G B R A C E S U P P O R T 2 BEND DEDUCTION TU B E S U P P O R T 2 PRESS BRAKE V DIE PRESS BRAKE PUNCH 2
PART NUMBER: AK-11-FDS-A014 DESCRIPTION: DISCHARGE PANWELDMENT 16L
.7 5 0 .5 0 0
6
5
4
DEVELOPMENT COMPANY THICKNESS:
DrawnBy: CRAIG
FOOD PROCESSING EQUIPMENT
DATE: 2/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
WEIGHT:383.374 REVISION 1
SCALE: 1:12 SHEET 1 OF 3
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
9
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
E
E
D
D
.200
C
C
11.053
.765
B
B
PARTNUMBER: AK-11-FDS-267 SIDE SUPPORT DISCHARGE DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: ASTM A36 Steel
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS: .187
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
DATE:2/16/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
3
FOOD PROCESSING EQUIPMENT
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:17.302 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
51.908
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
A
CUTOUT
5/22/2012
MILES
B
ADDED BENDS CHANGED BEND ANGLE
7/2/2012
APPROVED CRAIG S
C
MATERIAL
7/23/2012
RON A
E
E
D
D
69.500
1.656
11.000
.406
5.753
11.156
58.157
1.688
4.503
.250
C
C
R.062
R.156
11.000
11.000
B
B
PART NUMBER: AK-12-FDS-DB-005 DESCRIPTION: CORNCOVER DEVELOPMENT COMPANY
A
MATERIAL: 100 LB BLACK BELTING
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS:
C
DATE: 4/18/2012
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:0.860 REVISION C 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS
BELT LENGTH 35"
ZONE
REV.
DESCRIPTION
DATE
APPROVED
E
E
40.437
SECTION A-A SCALE 1 : 6
D
.375 TYP. D
.265 TYP.
6.250 TYP. 1.469 C
C
A .875
2.291
.500
A 6.429
B
B
8.250 .625
.500
10.250
19.937
10.250
PARTNUMBER: AK-11-FDS-DB-078 16L FDSSEEDSAVER BELT DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: BLACK BELTING
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS:
DATE:7/15/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:7.592 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS
BELT LENGTH 35"
ZONE
REV.
DESCRIPTION
DATE
APPROVED
E
E
40.437 .265 TYP.
D
D
.375 TYP.
SECTION A-A SCALE 1 : 6
6.250 TYP. C
C
1.469
.875
2.291
A
.500
A
5.583 .500 3X
B
B
8.250
.500 3X 5.500
14.719
14.718
5.500
PARTNUMBER: AK-11-FDS-DB-083 16L FDSSEEDSAVER BELT DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: BLACK BELTING
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS:
DATE:7/15/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:7.302 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS
BELT LENGTH 35"
ZONE
REV.
DESCRIPTION
DATE
APPROVED
E
E
6.250 TYP.
40.437
.375 TYP.
D
D
.265 TYP.
SECTION A-A SCALE 1 : 6
C
C
1.469 2.291
A .875
.500
A 5.583
.500 3X
8.250
B
5.500
14.718
14.719
B
.500 3X
5.500
PARTNUMBER: AK-11-FDS-DB-087 16L FDSSEEDSAVER BELT DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: BLACK BELTING
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
THICKNESS:
DATE:7/21/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:7.302 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
F
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
BELT LENGTH 35" SECTION A-A
F
1.298 7.500 TYP. 8.250 2X .265 TYP.
E
E
.375 TYP.
2.291 2X
D
D
62.596
C
C
A .500
.875
A
B
10.59
20.70
20.70
B
10.59
PARTNUMBER: AK-12-FDS-022 DESCRIPTION: 12LFDSSEEDSAVERBELT DEVELOPMENT COMPANY
A
MATERIAL: 100 LB BLACK BELTING PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 7
6
5
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
DATE:7/15/2011
DrawnBy: CRAIG
FINISH:
8
THICKNESS:
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:10.787 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
.500 2X
.500 TYP.
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
1.298 SECTION A-A
8.250 2X
F
7.500 TYP.
BELT LENGTH 35"
20.940
.265 TYP.
E
E
.375 TYP.
.500 2X
62.596 D
D
2.291 2X .500 4X
C
C
A .500 TYP. .875 TYP.
A
B
B
PARTNUMBER: AK-12-FDS-023 DESCRIPTION: 12LFDSSEEDSAVERBELT DEVELOPMENT COMPANY
A
MATERIAL: 100 LB BLACK BELTING PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 7
6
5
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
DATE:7/15/2011
DrawnBy: CRAIG
FINISH:
8
THICKNESS:
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:11.079 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
20.95
8
7
6
4
5
1
2
3
REVISIONS
DETAIL A SCALE 1 : 1
ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
2.000
E
E
81.445 .125 R.625 2X
D
D
R.141
C
C
B A
B
B
DETAIL B SCALE 1 : 1.5
1.000
R.500 2X
A
PART NUMBER: AK-11-FDS-DB-054 PANGUARD DESCRIPTION:
.124
.375
DEVELOPMENT COMPANY MATERIAL: ASTM A36 Steel FINISH: SAFETY YELLOW
.500 8
PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH
.750 7
6
5
THICKNESS: .062
DrawnBy: CRAIG
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
DATE: 6/9/2011
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
3
FOOD PROCESSING EQUIPMENT
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:3.378 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\16Ln Drive Back Concept\
.875
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
3.000
1.312 E
E
D
D
.390 1.062 1.260 .937
.625
.250
.937
1.500
.390 C
C
.813 1.938
.250 1.031
.281
B
.437 B
PARTNUMBER: AK-15-FDS-011 FRONT WHEEL SLIDE DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: Brass
THICKNESS:
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
DATE:8/27/2012
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 1:8 SHEET 1 OF 1
WEIGHT:1.529 REVISION 1
A
Drawing Location: F:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
BREAK ALL SHARP EDGES
8
7
6
4
5
1
2
3
REVISIONS ZONE
REV.
DESCRIPTION
DATE
APPROVED
F
3.000 .172
E
E
1.062
D
D
1.260
.875 .875
C
C
1.813 .265 1.000
1.500
.187
B
B
90.0°
PART NUMBER: AK-12-FDS-032 REARWHEEL SLIDE DESCRIPTION: DEVELOPMENT COMPANY
A
MATERIAL: Brass
THICKNESS:
DrawnBy: CRAIG
FINISH: PRESS BRAKE INFORMATION BEND DEDUCTION PRESS BRAKE V DIE PRESS BRAKE PUNCH 8
7
6
5
DATE: 8/27/2012
UNLESS OTHERWISE SPECIFIED TOLERANCE INFORMATION .X = + O R - .0 3 0
.XX = + OR - .020
FRACTION = + OR - 1/16"
4
FOOD PROCESSING EQUIPMENT
3
.XXX = + OR - .010
MANUFACTURE & DESIGN 410 CHAMBERS ST. EUGENE, OR 97402 - TEL (541) 686-0012 FAX (541) 485-2892 THIRD ANGLE PROJECTION
ANGLES = + OR - 1/2 DEG
2
SCALE: 2:1 SHEET 1 OF 1
WEIGHT:1.358 REVISION 1
A
Drawing Location: Q:\01-PMF-EngineeringOfficeFiles\Customer Info\A&K\A&K-2005 Thru 2050\Shaker\Flex Drive Feed Shaker\
.530
HALF TRANSFER DISASSEMBLY/ASSEMBLY INSTRUCTIONS
1. REMOVE METERING CONVEYOR
4. REMOVE INFEED PAN
2. REMOVE DRIVE SPRING BOARDS 5. REMOVE DISCHARGE PAN
3. SHAKERS INSTALLED BEFORE 2015 REMOVE HORIZONTAL SPRINGS
6. DISCONNECT LINEAR ACTUATOR
7. REMOVE SUB-FRAME RAIL BLOCK SPRING CLAMPS 8. REMOVE SUB-FRAME
REASSEMBLY
9. LOWER SUB-FRAME ONTO RAILS
10. RE-ATTACH RAIL BLOCK SPRING CLAMPS
11. RE-ATTACH LINEAR ACTUATOR
8 4
6 9
12. INSTALL DISCHARGE PAN SNOUTS UNDER HUSKER, THEN LOWER PAN ONTO SUB-FRAME
2 11 3
5
7 1
14. TIGHTEN DISCHARGE PAN SHAKER ARM BOLTS
LEAVE SHAKER ARM BOLTS LOOSE
13. PUT ON DRIVE SPRING BOARDS FROM BEARINGS TO DISCHARGE PAN, LEAVE LOOSE
15. TIGHTEN DISCHARGE PAN DRIVE SPRING BOARDS
16. INSTALL INFEED PAN - LEAVE SHAKER ARM BOLTS LOOSE
17. PUT ON DRIVE SPRING BOARDS FROM BEARINGS TO INFEED PAN, LEAVE LOOSE
8 4
6
2 7
11
9 3
5
1
18. TIGHTEN INFEED PAN SHAKER ARM BOLTS
19. TIGHTEN INFEED PAN DRIVE SPRING BOARDS
20. SHAKERS INSTALLED BEFORE 2015 - RE-INSTALL HORIZONAL SPRINGS
21. SET TO HEIGHT, LEVEL FRAME ADJUST EACH FOOT UP OR DOWN UNTIL THE FRAME IS LEVEL FROM C TO CORNER
HALF TRANSFER RAIL BLOCK REPLACEMENT INSTRUCTIONS
1. LOOSEN RAIL SPRING CLAMPS
2. LIFT SHAKER FRAME 1" OFF OF RAILS
3. REMOVE RAIL BLOCK
4. INSTALL NEW RAIL BLOCK
5. ON DISCHARGE END LIFT SHAKER 1" REPLACE WITH NEW BLOCK - WHEN TIGHTENING BOLT MAKE SURE SLIDE BLOCK CAN PIVOT - USE BLUE LOCTITE ON BOLT
6. LOWER SHAKER FRAME ONTO RAILS
7. RE-TIGHTEN RAIL SPRING CLAMPS TO 1/2" - OK TO TIGHTEN MORE AS LONG AS SHAKER MOVES IN & OUT WHILE RUNNING SHAKER MUST BE RUNNING TO MOVE IN & OUT
HALF TRANSFER RAIL REPLACEMENT INSTRUCTIONS
1. DISCONNECT & REMOVE LINEAR ACTUATOR
4. LIFT SHAKER FRAME OFF OF RAILS
2. REMOVE LINEAR ACTUATOR ARM
5. REMOVE BOLT & LOWER RAILS
3. LOOSEN ORANGE SPRING CLAMP
6. INSTALL NEW RAILS - LEVEL RAILS WITH
7. LOWER SHAKER FRAME ONTO RAILS
8. TIGHTEN ORANGE SPRING CLAMPS
ELECTRICAL BOX
9. RE-INSTALL LINEAR ACTUATOR MOUNT
10. RE-INSTALL LINEAR ACTUATOR - DO NOT SPIN LINEAR ACTUATOR TO ADJUST LENGTH USE EXTEND & RETRACT ELECTRICAL BOX TO LINE UP LINEAR ACTUATOR WITH MOUNT ON FRAME
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
FS‐208‐01‐MS SHAKER SNOUT, 8‐LANE & 16‐LANE MILD STEEL (#FS208‐01)
1
0
2
FS‐212‐01‐MS SHAKER SNOUT, 12‐LANE MILD STEEL (#FS212FDS‐A01)
0
1
0
318
SNOUT SECURING BRACKET W/HOOK (#FS‐220‐048)
1
2
2
317
OVERCENTER LATCH CLAMP (DE‐STACO) ( )
1
2
2
SNOUT SECURING BRACKET ‐ HARDWARE QTY REQUIRED PER HALF‐ TRANSFER A&K PART
ITEM DESCRIPTION
8‐LN
12‐LN
16‐LN
HTS‐16‐034
1/2" x 1" HEX HEAD BOLT
1
2
2
HTS‐16‐035
1/2" x 1 1/2" HEX HEAD BOLT
2
4
4
HTS‐16‐036
1/2" FLAT WASHER
3
6
6
HTS‐16‐037
1/2" LOCK WASHER
3
6
6
VII‐1
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
SHAKER SNOUT, 8‐LANE & 16‐LANE MILD STEEL (#FS208‐01)
FS‐208‐01‐MS
B
SHAKER SNOUT, 12‐LANE MILD STEEL (#FS212FDS‐A01) ( )
FS 212 01 MS FS‐212‐01‐MS
VII‐2
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS SHAKER SNOUT ASSEMBLY ‐ COMMON PARTS
LETTER
ITEM DESCRIPTION
PART #
A
SNOUT SECURING BRACKET W/HOOK (#FS‐220‐048)
318
B
OVERCENTER LATCH CLAMP (DE‐STACO #341)) ( ))
317
VII‐3
HALF TRANSFER SNOUT REPLACEMENT INSTRUCTIONS
1. LOOSEN SNOUT LATCH BARS 2. DISCONNECT SNOUT LATCH BARS
3. LOOSEN SNOUT MOUNT BOLTS
4. LIFT SNOUT
5. REMOVE SNOUT MOUNT BOLTS 6. REMOVE SNOUT
7. ALIGN NEW SNOUT MAKING SURE NUMBERS ON SNOUT MATCH NUMBERS ON PAN
8. INSTALL SNOUT MOUNT BOLTS, LEAVE LOOSE
9. PIVOT SNOUT DOWN
10. ATTACH SNOUT LATCH BARS 11. TIGHTEN SNOUT LATCH BARS
12. TIGHTEN SNOUT MOUNT BOLTS
A&K DEVELOPMENT COMPANY ‐ HALF TRANSFER SHAKER FEEDER COMMON PARTS COMMON PARTS
A&K PART # 305
305B
ITEM DESCRIPTION LARGE SHAKER ARM ASSY W/SPRINGS & HARDWARE (#FS250‐00) HARDWARE FOR LARGE SHAKER ARM (INCLUDES: (1) 3/8" X 5 1/2" HEX BOLT, (1) 3/8"‐ HARDWARE FOR LARGE SHAKER ARM (INCLUDES: (1) 3/8" X 5 1/2" HEX BOLT (1) 3/8" 16 NYLOCK HEX NUT, (2) 3/4"‐10 X 4" HEX BOLTS, (2) 3/4" LOCK WASHERS, (2) 3/4"‐10 FULL HEX NUTS, (2) 3/8"‐16 X 1 1/2" HEX BOLTS, (2) 3/8" FLAT WASHERS, (2) 3/8"‐16 NYLOCK HEX NUTS
313
LOWER SPRING ‐ HEAVY
314
UPPER SPRING LIGHT UPPER SPRING, LIGHT
317
OVERCENTER LATCH CLAMP (DE‐STACO #341))
318
SNOUT SECURING BRACKET W/HOOK (#FS‐220‐048)
335
BUSHING, LARGE SHAKER ARM (#FS250‐03 OR BUSHING #3885)
AK‐11‐FDS‐131
SHAKER SPRING LOWER MOUNT
AK‐11‐FDS‐267
SIDE SUPPORT DISCHARGE (DISCH. PAN WELDMENT)
AK‐11‐FDS‐A010
INFEED PAN WELDMENT, 16‐LANE SEED SAVER
AK‐11‐FDS‐A014
DISCHARGE PAN WELDMENT, 16‐LANE SEED SAVER
AK‐11‐FDS‐A046
DISCHARGE PAN WELDMENT ASSY, 12‐LANE
AK‐11‐FDS‐A051
DISCHARGE PAN WELDMENT ASSY, 8‐LANE (SEED SAVER)
AK‐11‐FDS‐A052
INFEED PAN WELDMENT ASSY, 8‐LANE
AK‐11‐FDS‐A052
INFEED PAN WELDMENT ASSY, 8‐LANE (SEED SAVER)
AK‐11‐FDS‐DB‐054
SAFETY RAILS (YELLOW)
AK‐11‐FDS‐DB‐075
STRAP, 8/16‐LANE SEED SAVER BELT
AK‐11‐FDS‐DB‐078
8/16‐LANE SEED SAVER BELT, BLACK W/GUIDES
AK‐11‐FDS‐DB‐083 AK 11 FDS DB 083
8/16‐LANE 8/16 LANE SEED SAVER BELT, BLACK RH SLOT SEED SAVER BELT, BLACK RH SLOT
AK‐11‐FDS‐DB‐087
8/16‐LANE SEED SAVER BELT, BLACK LH SLOT
VIII‐1
A&K DEVELOPMENT COMPANY ‐ COLOR SORTER SHAKER FEEDER COMMON PARTS COMMON PARTS
A&K PART #
ITEM DESCRIPTION
AK‐11‐FDS‐DB‐A02 INFEED PAN WELDMENT 16‐LANE AK‐11‐FDS‐DB‐A03 DISCHARGE PAN WELDMENT 16‐LANE AK‐12‐FDS‐022
12‐LANE SEED SAVER BELT (FOUR GUIDES)
AK‐12‐FDS‐023
12‐LANE SEED SAVER BELT (FOUR GUIDES)
AK‐12‐FDS‐024
STRAP, 12‐LANE SEED SAVER BELT
AK‐12‐FDS‐031
SPRING MOUNT PLATE
AK‐12‐FDS‐032
REAR SLIDE, WHEEL (BRASS)
AK‐12‐FDS‐DB‐004
CORN COVER BRACKET, 16‐LANE SPLIT PAN
AK‐12‐FDS‐DB‐005
CORN COVER (#100 BLACK BELTING), 16‐LANE SPLIT PAN
AK‐12‐FDS‐DB‐012
RAIL GUIDE, VERTICAL SPRING ASSY (ABOVE ORANGE SPRING)
AK‐12‐FDS‐DB‐013
SPRING CAPTURE (HORIZONTAL ASSY)
AK‐12‐FDS‐DB‐032
CORN COVER BACKING BAR, 16‐LANE SPLIT PAN
AK‐13‐CS‐A115
COLOR SORTER SHAKER DRIVE ASSEMBLY (SELL AS ONLY ASSY) COLOR SORTER SHAKER DRIVE ASSEMBLY (SELL AS ONLY ASSY)
AK‐13‐CS‐A116
DRIVE SPRING BOARD ASSY (4 PER SET) WITH HARDWARE
AK‐13‐CS‐A116A
FIBERBOARD ASSEMBLY (ONLY ONE FIBERBOARD)
AK‐13‐FDS‐121
SPRING PLATE
AK 13 FDS A034 AK‐13‐FDS‐A034
SUB SUB FRAME SPRING MOUNT WELDMENT, VERTICAL SPRING ASSY FRAME SPRING MOUNT WELDMENT VERTICAL SPRING ASSY
AK‐13‐FDS‐A037
PULLEY COVER ASSY
AK‐13‐FDS‐DB‐007
PULLEY BACK
AK‐15‐FDS‐011
FRONT SLIDE, WHEEL (BRASS)
AK‐15‐FDS‐012
MOTOR MOUNT, 8‐LANE, 12‐LANE
AK‐15‐FDS‐013
MOTOR MOUNT, 16‐LANE VIII‐2
A&K DEVELOPMENT COMPANY ‐ COLOR SORTER SHAKER FEEDER COMMON PARTS COMMON PARTS
A&K PART #
ITEM DESCRIPTION
AK‐15‐FDS‐042
SPRING MOUNT
AK‐15‐FDS‐A001
FLEX DRIVE SHAFT ASSY
AK‐15‐FDS‐A003
DISCHARGE PAN WELDMENT ASSY, 12‐LANE (SEED SAVER)
AK‐15‐FDS‐A004
INFEED PAN WELDMENT ASSY, 12‐LANE
AK‐15‐FDS‐A004
INFEED PAN WELDMENT ASSY, 12‐LANE (SEED SAVER)
AK‐15‐FDS‐A007
DISCHARGE PAN WELDMENT ASSY, 8‐LANE
AK‐15‐FDS‐DB‐016
MOUNTS, LINEAR ACTUATOR
FS‐208‐01‐MS
SHAKER SNOUT, 8‐LANE & 16‐LANE MILD STEEL (PRINT #FS208‐01)
FS‐212‐01‐MS
SHAKER SNOUT, 12‐LANE MILD STEEL (PRINT #FS212FDS‐A01)
FS‐250‐01
LARGE SHAKER ARM (SHAKER ARM ONLY W/BUSHINGS)
HTS‐16‐001
WORLDWIDE MOTOR, 1 HP, 1800 RPM, 56CB BASE (#NAT1‐18‐56CB)
HTS‐16‐002
SHEAVE 5/8", 60 HZ OPERATION
HTS‐16‐003
DRIVE PULLEY DRIVE PULLEY
HTS‐16‐004
V‐BELT, A38
HTS‐16‐005
LINEAR ACTUATOR (#CC58HD/E/101/AA36/S)
HTS‐16‐006
SHEAVE 7/8", 50 HZ OPERATION
HTS 16 007 HTS‐16‐007
BUSHING BUSHING STEEL SPLIT, DRIVE PULLEY STEEL SPLIT DRIVE PULLEY
HTS‐16‐008
1/4"‐20 X 3/4" GRADE 5 HEX HEAD BOLT
HTS‐16‐009
1/4" FLAT WASHER
HTS‐16‐010
1/4" LOCK WASHER
HTS‐16‐011
1/2"‐13 X 2" HEX HEAD BOLT
HTS‐16‐012
1/2"‐13 X 2 1/4" HEX HEAD BOLT VIII‐3
A&K DEVELOPMENT COMPANY ‐ COLOR SORTER SHAKER FEEDER COMMON PARTS COMMON PARTS
A&K PART #
ITEM DESCRIPTION
HTS‐16‐013
7/16" X 3/4" GRADE 5 HEX HEAD BOLT
HTS‐16‐014
1/2" FLAT WASHER / "
HTS‐16‐015
1/2" CAM LOCK WASHERS (2 PER)
HTS‐16‐016
7/16"‐14 X 1 3/4" GRADE 8
HTS‐16‐017
7/16" CAM LOCKS
HTS‐16‐018
5/16"‐18 X 1 1/2" GRADE 8
HTS‐16‐019
5/16" NYLOCKS
HTS‐16‐020
7/16" x 1 1/2" SOCKET HEAD CAP SCREW
HTS‐16‐021
7/16" CAM LOCKS (2 PER)
HTS‐16‐022
7/16"‐14 X 1/2" SOCKET HEAD CAP SCREW
HTS‐16‐023
3/4" X 5" HEX HEAD BOLT GRADE 8
HTS‐16‐024
3/4" JAM NUT
HTS‐16‐025 HTS 16 025
1/2"‐13 X 3 1/2" HEX HEAD NUT GRADE 8 1/2 13 X 3 1/2 HEX HEAD NUT GRADE 8
HTS‐16‐026
1/2+‐13 JAM NUT
HTS‐16‐027
1/2" NYLOCK NUT
HTS‐16‐028
1/2" FLAT WASHER
HTS 16 029 HTS‐16‐029
1/2" 13 X 12" GRADE 5 HEX HEAD BOLT 1/2"‐13 X 12" GRADE 5 HEX HEAD BOLT
HTS‐16‐030
1/4"‐20 NYLOCK NUT
HTS‐16‐031
1/4"‐20 FLAT WASHER
HTS‐16‐032
1/4"‐20 X 3/4" BUTTON HEAD CAP SCREW
HTS‐16‐033
1/4"‐20 LOCK WASHER
HTS‐16‐034
1/2" x 1" HEX HEAD BOLT VIII‐4
A&K DEVELOPMENT COMPANY ‐ COLOR SORTER SHAKER FEEDER COMMON PARTS COMMON PARTS
A&K PART #
ITEM DESCRIPTION
HTS‐16‐035
1/2" x 1 1/2" HEX HEAD BOLT
HTS 16 036 HTS‐16‐036
1/2" 1/2" FLAT WASHER FLAT WASHER
HTS‐16‐037
1/2" LOCK WASHER
HTS‐16‐038
CONTROL BOX, LINEAR ACTUATOR
LHL 1000D 01
ORANGE SPRING, VERTICAL SPRING ASSY (LEE SPRING #1000D‐01)
VIII‐5