‘WE MAKE THINGS FLOAT’
Twin Set Display Manual
Twin Set Display Manual Please take the time to read carefully through the instructions in this user manual. This will allow you to install and operate the Twin Set Display correctly. This manual contains important information about safety, use, limitations, warranty and technical support. You are strongly advised to read this user manual carefully prior to using the Twin Set Display. By taking the levitation module into use, you accept the terms and conditions that are stated in the user manual concerning safety, use, and technical support. Tip: Keep this user manual for future reference.
Contents
1 General Description
6
2 Using the Twin Set Display
7
a. Unpacking b. Placing the base c. Power connection d. Use of the carrier plateau e. How to set up the Twin Set Display f. Position of Ultrabook™ on the carrier plateau g. Switching the Twin Set Display off
3 Safety and Protection
a. General safety warnings b. Overheating c. Electromagnetic fields EMF d. Power Interruptions
4 Cleaning and maintenance
a. Cleaning b. Storage c. Replacement d. Environment
7 8 9 9 11 13 14
15 15 17 18 19
20 20 20 21 21
1 General Description The display contains 2 separate elements.
A)The internal main base supply and intergrated levitation system with mirror top. B)The Carrier Plateau which carries the product(s). Product Specifications Rated input voltage Rated frequency Rated input power Classification none Water penetration Conditions for use temp Relative humidity Storing conditions temp
100 - 240V 50 - 60Hz 60W max IP x 0 -10oC to +35oC from 30% to 90% -20oC to +50oC (no condensation)
You must take measures to prevent magnetic interference between this device and other appliances.
6
2 Using the Twin Set Display A. Unpacking - Carefully unpack the Levitation Display box. - Unwrap the carrier plateau and base. - The carrier plateau and the base are a matched set. - The base and carrier plateau are numbered. Please do not interchange them with other display sets. - Never hold the base module upside down. The magnet clamped mirror could possibly fall out.
7
B. Placing the base - The base should be placed on a flat horizontal surface. - Make sure, you keep the space between the knobs on the bottom of the base open, so ventilation air can enter through the bottom of the base. - Avoid bright lights on the sensors (black central ‘eyes’ on top of the base) - The Twin Set Display can only be used indoors. Avoid humid conditions. The Display can become - damaged due to moisture, humidity or liquids. Make sure the nearby surroundings of the Display - adheres to the general safety and warnings as stated in Section 3 and 4.
8
C. Power connection - Inside the base are two universal power adaptors which are combined into one power cable with a US power plug attached to it. - The device is turned on by putting the power plug into the power socket. There is no power button. - Never use the display when power cables seem to be damaged. - Do not try to replace the power cable(s). Please refer to your contact on the last page of this manual. D. Use of the carrier plateau - The carrier plateau is controlled by an optical system. Therefore you must not put anything between the sensor eyes of the base and the reflective spots, which can be seen on the bottom of the carrier plateau. Otherwise the carrier plateau will fall down. - Do not push or bump the carrier plateau from the sensors.
9
- Watch out! The Carrier Plateau is magnetic, it will attract iron and magnetic parts. It could influence objects that are vulnerable to magnetic fields. - When building something around the display, make sure it doesn’t have iron or other magnetic parts in it, as it can influence the levitation. !
- NEVER BRING TWO CARRIER PLATEAUS NEAR EACH OTHER! +35
-10
They will attract each other with force and they could be damaged!
10
E. How to setup the Twin Set Display Step 1) Place the base unit inside it ’s proper external housing. Step 2) Insert the powerplug into a powersocket. (see Topic C) You can see that both sensors have a faint red glow in the middle of each sensor. Step 3) Let the carrier plateau slightly rest on top of your fingers. Hold the the carrier plateau carefully above the sensor eyes. At the bottom of the carrier plateau there are 2 reflective dots, those should be positioned right above the sensor eyes. You can feel a ‘lock’ occur. This means that the levitation system has the carrier plateau in control. Step 4) Carefully let go of the carrier plateau. READY! !
+35
*Step 3 and 4 might require some practice. -10
11
Step 6) The base will keep the carrier plateau levitated. Always make sure that the carrier plateau is floating horizontally. If it’s leaning slightly backwards or sideways, then you must reposition the product(s) on the carrier plateau. If the carrier plateau and product(s) are not balanced correctly, the system might overheat. Heat protection will kick in and will shut the system down. If this happens, pull out the main plug, let the system cool off for 10 minutes, then repeat actions from step 2. Notes If the carrier plateau falls down, carefully ‘pull’ of the carrier plateau from the base and repeat actions starting from step 3. Make sure you never hold the base sideways or upside down, the mirror top could fall out and become damaged (Magnetic clamp).
12
F. Example : Position of Ultrabook™ on the carrier plateau Open the screen at approximately 100 degrees.
~ 100 degrees
Place the back of the Ultrabook™ exactly against the edge of the ‘location mark’ on the back of the carrier plateau.
location mark Sideview
13
G. Switching the Twin Set Display off - If the carrier plateau is in the levitating (floating) position, carefully remove the carrier plateau with the product(s) from the position and place it away from any metal or magnetic objects. - Pull the power plug out of the main socket. - Allow the Twin Set Display to cool off for 15 minutes before cleaning or storing. - When the Twin Set Display is stored, place the carrier plateau upside down with the reflective spots facing upwards. To prevent scratching put some cardboard / thick paper in between. - For Storage information see Chapter 4 topic B.
14
3 Safety and Protection A. General Safety Warnings - Please stay away from dangerous situations and refrain from creating dangerous situations mentioned below: - Water and electricity are an extremely dangerous combination. Do not use this device in a humid environment (for example a bathroom or in the immediate vicinity of a shower, swimming pool or aquarium, etc). - Do not allow water or other liquids to enter or land on the device. The Twin Set Display is not moisture-resistant. - Do not take the Twin Set Display apart unless you are qualified to do this to avoid the risk of electric shocks. Have maintenance and servicing carried out by qualified maintenance personnel. Please contact Crealev for further service. - Flames or other objects such as candles or heaters must not be placed on top of or near to the Twin Set Display. The power adaptor is suitable for voltages from 100V to - 240V. The powerplug connected to the adaptor is suited for the US.
15
- The mains supply operates with power adapter. They can only be replaced by qualified personnel. - Do not damage the power cable and avoid twisting the cable. - Never try to remove the rubber bottom of the carrier plateau. - This Twin Set Display is only intended for persons who are instructed to use this display. - Do not place any side or upward heavy burden on the Twin Set Display. - Situate the Twin Set Display on a stable, level surface and ensure that there is at least 20 cm free space around the device and 40 cm above the device to prevent overheating. - Never move the Twin Set Display during use. - Do not use the Twin Set Display at room temperatures lower than 14 degrees fahrenheit, or higher than 95 degrees fahrenheit.
16
- Ensure that ventilation openings at the bottom of the base remain open during use. - Allow the Twin Set Display to cool off for 15 minutes before cleaning or storing. - Never use the Twin Set Display if it is damaged or seems to malfunction. - The Twin Set Display does not have an on/off switch. If you would like to disconnect the appliance from the mains supply, remove the plug from the socket. Before doing so, remove the carrier plateau from its levitation position.
B. Overheating The Twin Set Display is equipped with an automatic overheating trip. If the appliance is insufficiently cooled ( if for example the ventilation openings are covered), the device switches off automatically. If the Twin Set Display is overloaded or if the base has too much excitation, due to imbalance, or other over burdening, the base can heat up and the thermal protection will shut the device down.
17
!
Temperatures:
oF +35 95 14 oF -10
The specified data apply when the Twin Set Display is placed on top of a table. Maximum operating temperature Minimum operating temperature Temperature rise base at no excitation Thermal shutdown case temperature
95 oF 14 oF 50 oF ≈131 oF
If the safety overheating protection shuts the device down, the carrier plateau with the product(s) will fall down on the base. Please be aware of potential danger considering the load and weight of and on the carrier plateau. If this happens, remove the cause of the overheating, remove the plug from the mains socket and allow the device to cool off for approximately 15 minutes. Then reinsert the plug into the socket.
C. Electromagnetic fields (EMF) Guidelines for magnetic sensitive objects: Due to the presence of magnets in the device and carrier plateau the module generates a magnetic field. This could be interfering with magnetic sensitive objects like a creditcard or pacemaker. 18
!
+35 Technical Note -10
Approximately 300 Gauss of magnetic field strength is safe for magnetic stripe devices like credit cards. Stray field at 2.5 cm (1 inch) distance <300 [Gauss] The Twin Set Display complies with all the guidelines for electromagnetic fields (EMF). Providing the Twin Set Display is used correctly and according to the instructions in this user manual, it is safe for use according to the now available scientific evidence.
D. Power Interruption
!
In the event that the power is interrupted, the carrier plateau will land on the base with great force. This occurs with a slap, but does not have a negative effect on the operation of the system. If this occurs, please restore power, ‘pull’ off the Carrier Plateau from the base and repeat the instructions ‘How to set up the levitation system’ from step 3. +35
-10
19
4 Cleaning and Maintenance A. Cleaning Always remove the plug from the mains socket and allow the Twin Set Display to cool for approximately 15 minutes before you clean it. Never use abrasive sponges, abrasive cleaning agents or aggressive solvents for cleaning the levitation module. Remove dust from the appliance. Dust can have a negative effect on the optical sensors and therefore on the operation of the Twin Set Display. Clean the exterior of the Twin Set Display with a clean damp cloth. Do not allow any water or other liquids to enter or land on the base module.
B. Storage Please store the Twin Set Display, preferably in the packaging or protective wrappings. Please store the Twin Set Display in a dry safe place without extreme temperature changes.
20
When the Twin Set Display is stored, place the carrier plateau upside down on the base with the reflective spots facing upward. This will prevent the permanent magnets from disturbing the rubber covering at the bottom of the carrier plateau.
C. Replacements The Twin Set Display has replaceble parts. The carrier plateau, the mirror, the module in the base, the fans and the power adaptors can be replaced. Replacement can only be done by qualified +35personnel.
!
-10 For replacement inquiries please call Crealev.
D. Environment Do not dispose of this device at the end of its lifecycle with the rest of the normal household refuse. Preferably deposit it at one of the government-indicated collection points so that it can be recycled. In doing so, you will be contributing to a cleaner living environment.
21
5 Declaration of Conformity We, Crealev BV Klokgebouw 170 5617 AB EINDHOVEN Netherlands declare under our sole responsibility that the product as originally delivered,
Name: Levitation Display System Type: CLD-CL2.3 Function: The Levitation Display System is able to levitate a laptop. The Levitation Display System consist of a base above which a magnetic carrier plateau floats. This carrier plateau serves as floatation plateau for laptops. The base contains electronic elements for stabilization of the Levitation Display System. The carrier plateau does not contain any electronics, it contains only passive permanent magnets. Complies with the essential requirements of the following European Directives, and carries the CE marking accordingly:
• • •
Low voltage directive: EN 2006/95/EC EMC directive: EN 2004/108/EC RoHS directive: EN 2002/95/EC
and conforms with the following harmonized European standards:
• • • • •
EN 60204-1: 2006 EN 61000-6-1: 2007 EN 61000-6-3: 2007 EN 14121-1 NEN 5509
Electrical safety, part 1 EMC, Immunity, part 6-1 EMC, Emission, part 6-3 Risk analysis Design for user manuals
Eindhoven, The Netherlands Ger Jansen Date: 20-3-2011 Director Crealev BV Signature:
Crealev BV Klokgebouw 170 5617 AB EINDHOVEN Netherlands
crealev@crealev.com www.crealev.com