SAB vpenjalni trni DIN69871

Tool holders DIN ISO 7388-1 (DIN 69871)

© SAB d.o.o.

2021

DIN ISO 7388-1 (DIN 69871)

L1

F2 L2

L6

A

L1

F2 L2

L6 A

A

DIN 69871 AD+B

D1

D2 D3

D8

D6

Cone

D1

D11

20°

D2

D1

A

2

E1

E1

L5

L7 L5

DIN 69871 A/AD

D1

D6 D8

D2 D3

L5

L7 L5

D3

D6

D8

D11

D12

L1

L2

L5

L6

L7

A

E1

F2

30

31.75 M12

13

50

<45

-

-

47.80 15.90 15.00 16.40 19.00 3.20

21

Min.35

40

44.45 M16

17

63.55

<50

M4

M4

68.40 15.90 18.50 22.80 25.00 3.20

27

Min.35

50

69.85 M24

25

97.50

<80

M4

M6

101.75 15.90 30.00 35.50 35.70 3.20

42

Min.35

Material: Case hardened steel with min. 900 N/mm² of tensile strength in core.

Execution: Case hardened 58±2 Hrc. Depth of case 0.6 - 0.8 mm. Black oxidised.

Accuracy: Taper angle AT3 quality class or better. Rougness Ra < 0.2

All dimensions in this catalogue are in millimeters unless otherwise specified.

3

DIN ISO 7388-1 (DIN 69871)

Key benefits of THERMO Shrink-fit: Unlike more traditional tool clamping systems, Shrink-fit toolholding employs heating and cooling properties of steel in order to achieve superior clamping force.

Inside diameter of the toolholder is precisely manufactured to be slightly smaller than the shank diameter of the cutting tool at the room temperature.

Using shrink-fit machine heat is applied to the toolholder allowing it to expand so that the cutting tool can fit in. Upon cooling down toolholder contracts to its original dimension the cutting tool.

This clamping system allows for certain benefits not found in more traditional clamping:

•

Superior tool runout - monobloc toolholder, without clamping elements (bolts, nuts, etc.)

•

Higher rigidity - tool shank is gripped 360 deg., through the whole bore length

•

Straightforward operation - fast tool change, less accessories required

•

Increased tool life - better chip load distribution along the cutting edge

•

Easier workpiece approach - thinner profile, reduced nose diameter, various toolholder lengths

•

Enhanced reach - with use of cylindrical shrink fit extensions

•

Internal coolant supply - delivering coolant through the toolholder to the tool edge for better chip removal and superior surface finish.

•

Coolant ports sealable using M4 screws.

•

High pressure nozzles for better coolant direction at higher rpm.

•

Extended spindle life - tool holders fine balanced G2.5 at 25 000 rpm or more.

•

Costs saving - higher machine productivity due to stable operation, increased feeds and speeds and cutting depths.

SAB has two decades worth of experience in supplying customers around the world with only top-quality Shrink fit toolholders.

4

DIN ISO 7388-1 (DIN 69871)

THERMO Shrink-fit chucks x1 x2 4.5° d3 d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

d1 3 3 3 4 4 4 5 5 5 6 6 6 8 8 8 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 20

d2 9 9 9 10 10 10 11 11 11 21 21 21 21 21 21 24 24 24 24 24 24 27 27 27 27 27 27 33 33 33 33 33 33

d3 19 25 31 20 26 32 21 27 33 27 27 27 27 27 27 32 32 32 32 32 32 34 34 34 34 34 34 42 42 42 42 42 42

x1 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160

x2 36 36 36 36 36 36 42 42 42 47 47 47 47 47 47 50 50 50 50 50 50 52 52 52

Code SF03.D30.080 SF03.D30.120 SF03.D30.160 SF04.D30.080 SF04.D30.120 SF04.D30.160 SF05.D30.080 SF05.D30.120 SF05.D30.160 SF06.D30.080 SF06.D30.120 SF06.D30.160 SF08.D30.080 SF08.D30.120 SF08.D30.160 SF10.D30.080 SF10.D30.120 SF10.D30.160 SF12.D30.080 SF12.D30.120 SF12.D30.160 SF14.D30.080 SF14.D30.120 SF14.D30.160 SF16.D30.080 SF16.D30.120 SF16.D30.160 SF18.D30.080 SF18.D30.120 SF18.D30.160 SF20.D30.080 SF20.D30.120 SF20.D30.160

30 Form AD

5

DIN ISO 7388-1 (DIN 69871)

THERMO Shrink-fit chucks x1 x2 4.5° d3 d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

40

Form AD+B

6

d1 3 3 3 4 4 4 5 5 5 6 6 6 8 8 8 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 20 25 25 25 32 32 32

d2 9 9 9 10 10 10 11 11 11 21 21 21 21 21 21 24 24 24 24 24 24 27 27 27 27 27 27 33 33 33 33 33 33 44 44 44 44 44 44

d3 19 25 31 20 26 32 21 27 33 27 27 27 27 27 27 32 32 32 32 32 32 34 34 34 34 34 34 42 42 42 42 42 42 53 53 53 53 53 53

x1 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 100 160 200 100 160 200

x2 36 36 36 36 36 36 42 42 42 47 47 47 47 47 47 50 50 50 50 50 50 52 52 52 58 58 58 63 63 63

Code SF03.D44.080 SF03.D44.120 SF03.D44.160 SF04.D44.080 SF04.D44.120 SF04.D44.160 SF05.D44.080 SF05.D44.120 SF05.D44.160 SF06.D44.080 SF06.D44.120 SF06.D44.160 SF08.D44.080 SF08.D44.120 SF08.D44.160 SF10.D44.080 SF10.D44.120 SF10.D44.160 SF12.D44.080 SF12.D44.120 SF12.D44.160 SF14.D44.080 SF14.D44.120 SF14.D44.160 SF16.D44.080 SF16.D44.120 SF16.D44.160 SF18.D44.080 SF18.D44.120 SF18.D44.160 SF20.D44.080 SF20.D44.120 SF20.D44.160 SF25.D44.100 SF25.D44.160 SF25.D44.200 SF32.D44.100 SF32.D44.160 SF32.D44.200

DIN ISO 7388-1 (DIN 69871)

3º THERMO Shrink-fit chucks

Slim execution

x1 x2 3° d3 d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

d1 3 3 3 4 4 4 5 5 5 6 6 6 8 8 8 10 10 10 12 12 12 16 16 16

d2 9 9 9 10 10 10 11 11 11 12 12 12 14 14 14 16 16 16 18 18 18 24 24 24

d3 15 19 23 16 20 24 17 21 25 18 22 26 20 24 28 22 26 30 24 28 32 30 34 38

x1 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160

x2 36 36 36 36 36 36 42 42 42 47 47 47 47 47 47

Code SF03.D44.080.3 SF03.D44.120.3 SF03.D44.160.3 SF04.D44.080.3 SF04.D44.120.3 SF04.D44.160.3 SF05.D44.080.3 SF05.D44.120.3 SF05.D44.160.3 SF06.D44.080.3 SF06.D44.120.3 SF06.D44.160.3 SF08.D44.080.3 SF08.D44.120.3 SF08.D44.160.3 SF10.D44.080.3 SF10.D44.120.3 SF10.D44.160.3 SF12.D44.080.3 SF12.D44.120.3 SF12.D44.160.3 SF16.D44.080.3 SF16.D44.120.3 SF16.D44.160.3

40

Form AD+B

7

DIN ISO 7388-1 (DIN 69871)

“3-in-1” THERMO Shrink-fit chucks

Internal coolant supply

x1 x2 4.5° d3 d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

1 - Open

40

Form AD+B

d1 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 25 32

d2 21 21 21 21 24 24 24 24 27 27 27 27 33 33 33 33 44 44

d3 27 27 27 27 32 32 32 32 34 34 34 34 42 42 42 42 53 53

x1 80 120 80 120 80 120 80 120 80 120 80 120 80 120 80 120 100 100

x2 36 36 36 36 42 42 47 47 47 47 50 50 50 50 52 52 58 63

2 - Closed

3 - High speed

Code SF06.D44.080.IK SF06.D44.120.IK SF08.D44.080.IK SF08.D44.120.IK SF10.D44.080.IK SF10.D44.120.IK SF12.D44.080.IK SF12.D44.120.IK SF14.D44.080.IK SF14.D44.120.IK SF16.D44.080.IK SF16.D44.120.IK SF18.D44.080.IK SF18.D44.120.IK SF20.D44.080.IK SF20.D44.120.IK SF25.D44.100.IK SF32.D44.100.IK

Including high speed nozzles and sealing plugs

8

DIN ISO 7388-1 (DIN 69871)

Extended “3-in-1” THERMO Shrink-fit chucks Internal coolant supply

x1 x2 2°

Radial runout ≤ 0,003 mm

d3 d2 d1

4.5°

1 - Open

d1 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 25 25 32 32

2 - Closed

G2.5 at 25 000 min-1I

3 - High speed

d2 21 21 21 21 24 24 24 24 27 27 27 27 33 33 33 33 44 44 44 44

d3 34 37 34 37 38 41 38 41 40.5 43.5 40.5 43.5 48 51 48 51 53 53 53 53

x1 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200

x2 36 36 36 36 42 42 47 47 47 47 50 50 50 50 52 52 58 58 63 63

Code SF06.D44.160.IK SF06.D44.200.IK SF08.D44.160.IK SF08.D44.200.IK SF10.D44.160.IK SF10.D44.200.IK SF12.D44.160.IK SF12.D44.200.IK SF14.D44.160.IK SF14.D44.200.IK SF16.D44.160.IK SF16.D44.200.IK SF18.D44.160.IK SF18.D44.200.IK SF20.D44.160.IK SF20.D44.200.IK SF25.D44.160.IK SF25.D44.200.IK SF32.D44.160.IK SF32.D44.200.IK

40

Form AD+B

Including high speed nozzles and sealing plugs Vibration-dampening tapered profile

9

DIN ISO 7388-1 (DIN 69871)

THERMO Shrink-fit chucks Compact execution

x1 x2 4.5° d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

40

Form AD+B

10

d1 3 4 5 6 8 10 12 14 16 18 20 25 32

d2 9 10 11 20 20 24 27 33 33 44 44 46 47

x1 65 65 65 65 65 65 65 70 70 70 70 70 75

x2 36 36 42 47 47 50 50 50 56 58

Code SF03.D44.065 SF04.D44.065 SF05.D44.065 SF06.D44.065 SF08.D44.065 SF10.D44.065 SF12.D44.065 SF14.D44.070 SF16.D44.070 SF18.D44.070 SF20.D44.070 SF25.D44.070 SF32.D44.075

DIN ISO 7388-1 (DIN 69871)

End mill holders Slim execution

x1

d3 d2 d1

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

d1 6 6 6 8 8 8 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 20 25 25 25 32 32 32

d2 17 17 17 21 21 21 24 24 24 27 27 27 29 29 29 33 33 33 35 35 35 39 39 39 47 47 47 57 57 57

d3 25 30 31 29 35 35 32 37 38 35 40 41 37 42 43 41 46 47 43 48 49 47 50 50 47 47 47 57 57 57

x1 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160 100 130 160

Code WE06.D44.100F WE06.D44.130F WE06.D44.160F WE08.D44.100F WE08.D44.130F WE08.D44.160F WE10.D44.100F WE10.D44.130F WE10.D44.160F WE12.D44.100F WE12.D44.130F WE12.D44.160F WE14.D44.100F WE14.D44.130F WE14.D44.160F WE16.D44.100F WE16.D44.130F WE16.D44.160F WE18.D44.100F WE18.D44.130F WE18.D44.160F WE20.D44.100F WE20.D44.130F WE20.D44.160F WE25.D44.100F WE25.D44.130F WE25.D44.160F WE32.D44.100F WE32.D44.130F WE32.D44.160F

40

Form AD+B

11

DIN ISO 7388-1 (DIN 69871)

End mill holders x1

d2 d1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

40

Form AD+B

12

d1 6 6 6 6 6 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 14 14 14 14 14 16 16 16 16 16 16

d2 25 25 25 25 25 28 28 28 28 28 35 35 35 35 35 42 42 42 42 42 44 44 44 44 44 48 48 48 48 48 48

x1 50 100 120 160 200 50 100 120 160 200 50 100 120 160 200 50 100 120 160 200 50 100 120 160 200 35 63 100 120 160 200

Code WE06.D44.050 WE06.D44.100 WE06.D44.120 WE06.D44.160 WE06.D44.200 WE08.D44.050 WE08.D44.100 WE08.D44.120 WE08.D44.160 WE08.D44.200 WE10.D44.050 WE10.D44.100 WE10.D44.120 WE10.D44.160 WE10.D44.200 WE12.D44.050 WE12.D44.100 WE12.D44.120 WE12.D44.160 WE12.D44.200 WE14.D44.050 WE14.D44.100 WE14.D44.120 WE14.D44.160 WE14.D44.200 WE16.D44.035 WE16.D44.063 WE16.D44.100 WE16.D44.120 WE16.D44.160 WE16.D44.200

DIN ISO 7388-1 (DIN 69871)

End mill holders x1

d2 d1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

d1 18 18 18 18 18 20 20 20 20 20 20 25 25 25 25 25 25 32 32 32 32 32 40

d2 50 50 50 50 50 52 52 52 52 52 52 50 50 65 65 65 65 52 52 72 72 72 90

x1 63 100 120 160 200 35 63 100 120 160 200 35 60 100 120 160 200 45 63 100 160 200 120

Code WE18.D44.063 WE18.D44.100 WE18.D44.120 WE18.D44.160 WE18.D44.200 WE20.D44.035 WE20.D44.063 WE20.D44.100 WE20.D44.120 WE20.D44.160 WE20.D44.200 WE25.D44.035 WE25.D44.060 WE25.D44.100 WE25.D44.120 WE25.D44.160 WE25.D44.200 WE32.D44.045 WE32.D44.063 WE32.D44.100 WE32.D44.160 WE32.D44.200 WE40.D44.120

40

Form AD+B

13

DIN ISO 7388-1 (DIN 69871)

End mill holders

Internal coolant supply

d2

Radial runout ≤ 0,003 mm

d1

x1

G6.3 at 25 000 min-1

40

Form AD+B

14

d1 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 25 32 40

d2 25 25 28 28 35 35 42 42 44 44 48 48 50 50 52 52 65 72 90

x1 50 100 50 100 50 100 50 100 50 100 63 100 63 100 63 100 100 100 120

Code WE06.D44.050.IK WE06.D44.100.IK WE08.D44.050.IK WE08.D44.100.IK WE10.D44.050.IK WE10.D44.100.IK WE12.D44.050.IK WE12.D44.100.IK WE14.D44.050.IK WE14.D44.100.IK WE16.D44.050.IK WE16.D44.100.IK WE18.D44.050.IK WE18.D44.100.IK WE20.D44.050.IK WE20.D44.100.IK WE25.D44.100.IK WE32.D44.100.IK WE40.D44.120.IK

DIN ISO 7388-1 (DIN 69871)

Collet chucks 1:10 for DIN6388 collets x1

d1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

Range 1.5 - 16 1.5 - 16 1.5 - 16 2 - 25 2 - 25 2 - 25 4 - 32 4 - 32

x1 70 100 160 70 100 160 80 140

d1 43 43 43 60 60 60 72 72

Code SP16.D44.070 SP16.D44.100 SP16.D44.160 SP25.D44.070 SP25.D44.100 SP25.D44.160 SP32.D44.080 SP32.D44.140

40

Form AD+B

15

DIN ISO 7388-1 (DIN 69871)

ER Collet chucks d1

x1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

40

Form AD+B

16

ER 16 16 16 16 16 20 20 20 20 20 25 25 25 25 25 32 32 32 32 32 40 40 40 40 40

Range 0.5 - 10 0.5 - 10 0.5 - 10 0.5 - 10 0.5 - 10 1 - 13 1 - 13 1 - 13 1 - 13 1 - 13 1 - 16 1 - 16 1 - 16 1 - 16 1 - 16 2 - 20 2 - 20 2 - 20 2 - 20 2 - 20 3 - 26 3 - 26 3 - 26 3 - 26 3 - 26

x1 63 100 130 160 200 70 100 130 160 200 60 100 130 160 200 70 100 130 160 200 80 100 130 160 200

d1 28 28 28 28 28 35 35 35 35 35 42 42 42 42 42 50 50 50 50 50 63 63 63 63 63

Code ER16.D44.063 ER16.D44.100 ER16.D44.130 ER16.D44.160 ER16.D44.200 ER20.D44.070 ER20.D44.100 ER20.D44.130 ER20.D44.160 ER20.D44.200 ER25.D44.060 ER25.D44.100 ER25.D44.130 ER25.D44.160 ER25.D44.200 ER32.D44.070 ER32.D44.100 ER32.D44.130 ER32.D44.160 ER32.D44.200 ER40.D44.080 ER40.D44.100 ER40.D44.130 ER40.D44.160 ER40.D44.200

DIN ISO 7388-1 (DIN 69871)

ER Collet chucks Mini execution

x1

d1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

ER 11 11 11 16 16 16

Range 0.5 - 7 0.5 - 7 0.5 - 7 0.5 - 10 0.5 - 10 0.5 - 10

x1 70 100 160 70 100 160

d1 16 16 16 22 22 22

Code ER11.D44.070M ER11.D44.100M ER11.D44.160M ER16.D44.070M ER16.D44.100M ER16.D44.160M

20 20 20 25 25 25

1 - 13 1 - 13 1 - 13 1 - 16 1 - 16 1 - 16

70 100 160 70 100 160

28 28 28 35 35 35

ER20.D44.070M ER20.D44.100M ER20.D44.160M ER25.D44.070M ER25.D44.100M ER25.D44.160M

40

Form AD+B

17

DIN ISO 7388-1 (DIN 69871)

Morse taper holders for drills x1

d1

Radial runout ≤ 0,005 mm G6.3 at 25 000 min-1

40

Form AD+B

MK 1 1 2 2 3 3 4 4

x1 50 100 50 116 70 136 95 167

d1 25 25 32 32 40 40 48 48

Code MK1B.D44.050 MK1B.D40.100AD MK2B.D44.050 MK2B.D40.116AD MK3B.D44.070 MK3B.D40.136AD MK4B.D44.095 MK4B.D40.167AD

Morse taper holders for mills x1

d1

Radial runout ≤ 0,005 mm G6.3 at 25 000 min-1

40

Form AD+B

18

MK 1 2 3 4

x1 50 50 70 95

d1 25 32 40 48

Code MK1A.D44.050 MK2A.D44.050 MK3A.D44.070 MK3A.D44.095

DIN ISO 7388-1 (DIN 69871)

Threaded shank milling cutter holders x1 A

d3 d2 M

Radial runout ≤ 0,003 mm G2.5 at 25 000 min-1

M M6 M6 M6 M6 M8 M8 M8 M8 M10 M10 M10 M10 M10 M12 M12 M12 M12 M12 M12 M16 M16 M16 M16 M16 M16

A 25 50 75 100 25 50 75 100 25 50 75 100 125 25 50 75 100 125 150 25 50 75 100 125 150

x1 44 69 94 119 44 69 94 119 44 69 94 119 144 44 69 94 119 144 169 44 69 94 119 144 169

d2 10 10 10 10 13 13 13 13 18 18 18 18 18 21 21 21 21 21 21 29 29 29 29 29 29

d3 13 20 23 25 15 23 23 25 20 23 28 32 32 24 24 31 33 36 40 29 34 34 36 40 42.5

Code EF06.D44.044 EF06.D44.069 EF06.D44.094 EF06.D44.119 EF08.D44.044 EF08.D44.069 EF08.D44.094 EF08.D44.119 EF10.D44.044 EF10.D44.069 EF10.D44.094 EF10.D44.119 EF10.D44.144 EF12.D44.044 EF12.D44.069 EF12.D44.094 EF12.D44.119 EF12.D44.144 EF12.D44.169 EF16.D44.044 EF16.D44.069 EF16.D44.094 EF16.D44.119 EF16.D44.144 EF16.D44.169

40

Form AD+B

19

DIN ISO 7388-1 (DIN 69871)

Combi shell mill holders for milling cutters d2

Radial runout ≤ 0,005 mm

d1

x1

G6.3 at 25 000 min-1 l1

40 Form AD

20

d1 16 16 16 22 22 22 27 27 27 32 32 32 40 40 40

x1 55 100 150 55 100 150 55 100 150 60 100 150 60 100 150

x2 45 90 140 43 88 138 43 88 138 46 86 136 46 86 136

d2 32 32 32 40 40 40 48 48 48 58 58 58 70 70 70

x2

l2 27 27 27 31 31 31 33 33 33 38 38 38 41 41 41

Code KD16.D40.055 KD16.D40.100 KD16.D40.150 KD22.D40.055 KD22.D40.100 KD22.D40.150 KD27.D40.055 KD27.D40.100 KD27.D40.150 KD32.D40.060 KD32.D40.100 KD32.D40.150 KD40.D40.060 KD40.D40.100 KD40.D40.150

DIN ISO 7388-1 (DIN 69871)

Shell mill holders for cutters with driving slot

Internal coolant supply

x1

Radial runout ≤ 0,005 mm

d1

d2

l1

G6.3 at 25 000 min-1

x2

d1 16 16 16 16 16 22 22 22 22 22 27 27 27 27 27 32 32 32 32 32 40 40

x1 35 100 130 160 200 35 100 130 160 200 35 100 130 160 200 50 100 130 160 200 50 100

l1 17 17 17 17 17 19 19 19 19 19 21 21 21 21 21 24 24 24 24 24 27 27

d2 38 38 38 38 38 50 50 50 50 50 50 50 50 50 50 78 78 78 78 78 89 89

Code AD16.D44.035 AD16.D44.100 AD16.D44.130 AD16.D44.160 AD16.D44.200 AD22.D44.035 AD22.D44.100 AD22.D44.130 AD22.D44.160 AD22.D44.200 AD27.D44.035 AD27.D44.100 AD27.D44.130 AD27.D44.160 AD27.D44.200 AD32.D44.050 AD32.D44.100 AD32.D44.130 AD32.D44.160 AD32.D44.200 AD40.D44.050 AD40.D44.100

40

Form AD+B

21

DIN ISO 7388-1 (DIN 69871)

Holders for indexable inserts drills

d2

Radial runout ≤ 0,005 mm G6.3 at 25 000 min-1

40

Form AD+B

d1 20 25 32

d1

x1

x1 65 70 75

d2 40 45 52

Code VB20.D44.065 VB25.D44.070 VB32.D44.075

Quick-change tapping heads

d1

x1

Length compensation in compression and tension.

40

Form AD+B

22

Tap size M3 - M14 M6 - M24 M14 - M33 M22 - M48

Compensation ± 7.5 ± 12.5 ± 20.0 ± 22.5

Insert size 1 2 3 4

x1 74 98 169 185

d1 36 53 78 96

Code GN12.D40.074 GN20.D40.098 GN33.D40.169 GN48.D40.185

DIN ISO 7388-1 (DIN 69871)

HV drill chucks for RH and LH rotation x1

d1

Radial runout ≤ 0,02 mm G2.5 at 25 000 min-1

mm 0.3 - 8 0.5 - 13 1 - 16

x1 70 76 80

d1 36 44 51

Code HV08.D40.070 HV13.D40.076 HV16.D40.080

40 Form AD

Integrated precision drill chuck with Hexagonal key lock.

For drilling, milling, reaming and tapping.

Through coolant.

Drill chuck slipping impossible due to chuck being screwed with the holder body.

Compact design, enhanced reach.

Range up to 8, 13 or 16 mm.

NC drill chucks for RH rotation x1

d1

Special wrench supplied.

Radial runout ≤ 0,03 mm G6.3 at 12 000 min-1

mm 0-8 0 - 10 1 - 13 3 - 16

x1 70 74 80 97

d1 37 43 48 53

Code NC08.D40.070 NC10.D40.074 NC13.D40.080 NC16.D40.097

40 Form A

Integrated drill chuck with high clamping force achieved through special wrench.

2x chucking torque vs. hand tightening.

Drill bit slipping nearly impossible.

Drill chuck slipping impossible due to chuck being screwed with the holder body.

Compact design, external coolant supply.

Range up to 8, 10, 13 or 16 mm.

23

DIN ISO 7388-1 (DIN 69871)

Blank bars x1

Machineable soft body.

d1

Cone and flange hardened and finished.

Pre-balanced

40 Form A

d1 63.5 63.5

x1 160 250

Code RL63.D40.160 RL63.D40.250

Test bars x1

Precisely ground length and diameter.

d1

Radial runout ≤ 0,003 mm Test certificate and protective case supplied.

40 Form A

24

d1 40

x1 250

Code TB40.D40.250

© SAB d.o.o.

2021

25

DIN ISO 7388-1 (DIN 69871)

THERMO Shrink-fit chucks x1 x2 4.5° d3 d2 d1

Radial runout ≤ 0,003 mm Balanced G2.5 at 25 000 min-1

50

Form AD+B

26

d1 3 3 3 4 4 4 5 5 5 6 6 6 8 8 8 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 20 25 25 25 32 32 32

d2 9 9 9 10 10 10 11 11 11 21 21 21 21 21 21 24 24 24 24 24 24 27 27 27 27 27 27 33 33 33 33 33 33 44 44 44 44 44 44

d3 19 25 31 20 26 32 21 27 33 27 27 27 27 27 27 32 32 32 32 32 32 34 34 34 34 34 34 42 42 42 42 42 42 53 53 53 53 53 53

x1 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160 100 120 160 100 120 160

x2 36 36 36 36 36 36 42 42 42 47 47 47 47 47 47 50 50 50 50 50 50 52 52 52 58 58 58 63 63 63

Code SF03.D55.080 SF03.D55.120 SF03.D55.160 SF04.D55.080 SF04.D55.120 SF04.D55.160 SF05.D55.080 SF05.D55.120 SF05.D55.160 SF06.D55.080 SF06.D55.120 SF06.D55.160 SF08.D55.080 SF08.D55.120 SF08.D55.160 SF10.D55.080 SF10.D55.120 SF10.D55.160 SF12.D55.080 SF12.D55.120 SF12.D55.160 SF14.D55.080 SF14.D55.120 SF14.D55.160 SF16.D55.080 SF16.D55.120 SF16.D55.160 SF18.D55.080 SF18.D55.120 SF18.D55.160 SF20.D55.080 SF20.D55.120 SF20.D55.160 SF25.D55.100 SF25.D55.120 SF25.D55.160 SF32.D55.100 SF32.D55.120 SF32.D55.160

DIN ISO 7388-1 (DIN 69871)

3º THERMO Shrink-fit chucks Slim execution

x1 x2 3° d3 d2 d1

Radial runout ≤ 0,003 mm Balanced G2.5 at 25 000 min-1

d1 6 6 6 8 8 8 10 10 10 12 12 12 16 16 16

d2 12 12 12 14 14 14 16 16 16 18 18 18 24 24 24

d3 18 22 26 20 24 28 22 26 30 24 28 32 30 34 38

x1 80 120 160 80 120 160 80 120 160 80 120 160 80 120 160

x2 36 36 36 36 36 36 42 42 42 47 47 47 47 47 47

Code SF06.D55.080.3 SF06.D55.120.3 SF06.D55.160.3 SF08.D55.080.3 SF08.D55.120.3 SF08.D55.160.3 SF10.D55.080.3 SF10.D55.120.3 SF10.D55.160.3 SF12.D55.080.3 SF12.D55.120.3 SF12.D55.160.3 SF16.D55.080.3 SF16.D55.120.3 SF16.D55.160.3

50

Form AD+B

THERMO Shrink-fit chucks

Compact execution

x1 x2 4.5° d2 d1

Radial runout ≤ 0,003 mm Balanced G2.5 at 25 000 min-1

d1 6 8 10 12 14 16 18 20 25 32

d2 20 20 24 27 33 33 44 44 46 47

x1 65 65 65 65 70 70 70 70 70 75

x2 36 36 42 47 47 50 50 50 56 58

Code SF06.D55.065 SF08.D55.065 SF10.D55.065 SF12.D55.065 SF14.D55.070 SF16.D55.070 SF18.D55.070 SF20.D55.070 SF25.D55.070 SF32.D55.075

50

Form AD+B

27

DIN ISO 7388-1 (DIN 69871)

“3-in-1” THERMO Shrink-fit chucks Internal coolant supply

x1 x2 4.5°

Balanced G2.5 at 25 000 min-1

d3 d2 d1

Radial runout ≤ 0,003 mm

1 - Open

50

Form AD+B

d1 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 25 25 32 32

d2 21 21 21 21 24 24 24 24 27 27 27 27 33 33 33 33 44 44 44 44

d3 27 27 27 27 32 32 32 32 34 34 34 34 42 42 42 42 53 53 53 53

x1 80 120 80 120 80 120 80 120 80 120 80 120 80 120 80 120 100 120 100 120

x2 36 36 36 36 42 42 47 47 47 47 50 50 50 50 52 52 58 58 63 63

2 - Closed

3 - High speed

Code SF06.D55.080.IK SF06.D55.120.IK SF08.D55.080.IK SF08.D55.120.IK SF10.D55.080.IK SF10.D55.120.IK SF12.D55.080.IK SF12.D55.120.IK SF14.D55.080.IK SF14.D55.120.IK SF16.D55.080.IK SF16.D55.120.IK SF18.D55.080.IK SF18.D55.120.IK SF20.D55.080.IK SF20.D55.120.IK SF25.D55.100.IK SF25.D55.120.IK SF32.D55.100.IK SF32.D55.120.IK

Including high speed nozzles and sealing plugs

28

DIN ISO 7388-1 (DIN 69871)

Extended “3-in-1” THERMO Shrink-fit chucks Internal coolant supply

x1 x2 2°

Radial runout ≤ 0,003 mm

d3 d2 d1

4.5°

1 - Open

d1 6 6 8 8 10 10 12 12 14 14 16 16 18 18 20 20 25 25 32 32

2 - Closed

G2.5 at 25 000 min-1

3 - High speed

d2 21 21 21 21 24 24 24 24 27 27 27 27 33 33 33 33 44 44 44 44

d3 34 37 34 37 38 41 38 41 40.5 43.5 40.5 43.5 47.5 50.5 47.5 50.5 58.5 61.5 58.5 61.5

x1 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200 160 200

x2 36 36 36 36 42 42 47 47 47 47 50 50 50 50 52 52 58 58 63 63

Code SF06.D55.160.IK SF06.D55.200.IK SF08.D55.160.IK SF08.D55.200.IK SF10.D55.160.IK SF10.D55.200.IK SF12.D55.160.IK SF12.D55.200.IK SF14.D55.160.IK SF14.D55.200.IK SF16.D55.160.IK SF16.D55.200.IK SF18.D55.160.IK SF18.D55.200.IK SF20.D55.160.IK SF20.D55.200.IK SF25.D55.160.IK SF25.D55.200.IK SF32.D55.160.IK SF32.D55.200.IK

50

Form AD+B

Including high speed nozzles and sealing plugs Vibration-dampening tapered profile

29

DIN ISO 7388-1 (DIN 69871)

End mill holders x1

d2 d1

Radial runout ≤ 0,003 mm Balanced G6.3 at 18 000 min-1

50

Form AD+B

30

d1 6 6 6 6 6 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 14 14 14 14 14 16 16 16 16 16 18 18 18 18 18 20 20 20 20 20

d2 25 25 25 25 25 28 28 28 28 28 35 35 35 35 35 42 42 42 42 42 44 44 44 44 44 48 48 48 48 48 50 50 50 50 50 52 52 52 52 52

x1 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200 63 100 120 160 200

Code WE06.D55.063 WE06.D55.100 WE06.D55.120 WE06.D55.160 WE06.D55.200 WE08.D55.063 WE08.D55.100 WE08.D55.120 WE08.D55.160 WE08.D55.200 WE10.D55.063 WE10.D55.100 WE10.D55.120 WE10.D55.160 WE10.D55.200 WE12.D55.063 WE12.D55.100 WE12.D55.120 WE12.D55.160 WE12.D55.200 WE14.D55.063 WE14.D55.100 WE14.D55.120 WE14.D55.160 WE14.D55.200 WE16.D55.063 WE16.D55.100 WE16.D55.120 WE16.D55.160 WE16.D55.200 WE18.D55.063 WE18.D55.100 WE18.D55.120 WE18.D55.160 WE18.D55.200 WE20.D55.063 WE20.D55.100 WE20.D55.120 WE20.D55.160 WE20.D55.200

DIN ISO 7388-1 (DIN 69871)

End mill holders x1

d2 d1

Radial runout ≤ 0,003 mm Balanced G6.3 at 18 000 min-1

d1 25 25 25 25 25 25 32 32 32 32 32 40 50

d2 50 65 65 65 65 65 65 72 72 72 72 90 90

x1 35 80 100 120 160 200 35 100 120 160 200 100 125

Code WE25.D55.035 WE25.D55.080 WE25.D55.100 WE25.D55.120 WE25.D55.160 WE25.D55.200 WE32.D55.035 WE32.D55.100 WE32.D55.120 WE32.D55.160 WE32.D55.200 WE40.D55.100 WE50.D55.125

50

Form AD+B

End mill holders Internal coolant supply

Radial runout ≤ 0,003 mm

d1

d2

x1

Balanced G6.3 at 18 000 min-1

d1 6 8 10 12 14 16 18 20 25 32 40

d2 25 28 35 42 44 48 50 52 65 72 90

x1 63 63 63 63 63 63 63 63 80 100 100

Code WE06.D55.063.IK WE08.D55.063.IK WE10.D55.063.IK WE12.D55.063.IK WE14.D55.063.IK WE16.D55.063.IK WE18.D55.063.IK WE20.D55.063.IK WE25.D55.080.IK WE32.D55.100.IK WE40.D55.100.IK

50

Form AD+B

31

DIN ISO 7388-1 (DIN 69871)

End mill holders Slim execution

x1

d3 d2 d1

Radial runout ≤ 0,003 mm G6.3 at 25 000 min-1

50

Form AD+B

32

d1 6 6 6 6 8 8 8 8 10 10 10 10 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 25 25 25 25 32 32 32

d2 17 17 17 17 21 21 21 21 24 24 24 24 27 27 27 27 29 29 29 29 33 33 33 33 35 35 35 35 39 39 39 39 47 47 47 47 57 57 57

d3 25 30 31 40 29 35 35 44 32 37 38 47 35 40 41 50 37 42 43 52 41 46 47 56 43 48 49 58 47 52 53 62 55 60 61 70 70 71 72

x1 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 100 130 160 200 130 160 200

Code WE06.D55.100F WE06.D55.130F WE06.D55.160F WE06.D55.200F WE08.D55.100F WE08.D55.130F WE08.D55.160F WE08.D55.200F WE10.D55.100F WE10.D55.130F WE10.D55.160F WE10.D55.200F WE12.D55.100F WE12.D55.130F WE12.D55.160F WE12.D55.200F WE14.D55.100F WE14.D55.130F WE14.D55.160F WE14.D55.200F WE16.D55.100F WE16.D55.130F WE16.D55.160F WE16.D55.200F WE18.D55.100F WE18.D55.130F WE18.D55.160F WE18.D55.200F WE20.D55.100F WE20.D55.130F WE20.D55.160F WE20.D55.200F WE25.D55.100F WE25.D55.130F WE25.D55.160F WE25.D55.200F WE32.D55.130F WE32.D55.160F WE32.D55.200F

DIN ISO 7388-1 (DIN 69871)

Collet chucks 1:10 for DIN6388 collets x1

d1

Radial runout ≤ 0,003 mm G6.3 at 18 000 min-1

Range 1.5 - 16 1.5 - 16 1.5 - 16 2 - 25 2 - 25 2 - 25 4 - 32 4 - 32

x1 70 100 160 70 100 160 80 140

d1 43 43 43 60 60 60 72 72

Code SP16.D55.070 SP16.D55.100 SP16.D55.160 SP25.D55.070 SP25.D55.100 SP25.D55.160 SP32.D55.080 SP32.D55.140

50

Form AD+B

33

DIN ISO 7388-1 (DIN 69871)

ER Collet chucks x1

d1

Radial runout ≤ 0,003 mm Balanced G6.3 at 18 000 min-1

50

Form AD+B

34

ER 16 16 16 16 16 25 25 25 25 25 32 32 32 32 32 40 40 40 40 40

Range 0.5 - 10 0.5 - 10 0.5 - 10 0.5 - 10 0.5 - 10 1 - 16 1 - 16 1 - 16 1 - 16 1 - 16 2 - 20 2 - 20 2 - 20 2 - 20 2 - 20 3 - 26 3 - 26 3 - 26 3 - 26 3 - 26

x1 63 100 130 160 200 60 100 130 160 200 70 100 130 160 200 80 100 130 160 200

d1 28 28 28 28 28 42 42 42 42 42 50 50 50 50 50 63 63 63 63 63

Code ER16.D55.063 ER16.D55.100 ER16.D55.130 ER16.D55.160 ER16.D55.200 ER25.D55.060 ER25.D55.100 ER25.D55.130 ER25.D55.160 ER25.D55.200 ER32.D55.070 ER32.D55.100 ER32.D55.130 ER32.D55.160 ER32.D55.200 ER40.D55.080 ER40.D55.100 ER40.D55.130 ER40.D55.160 ER40.D55.200

DIN ISO 7388-1 (DIN 69871)

ER Collet chucks Mini execution

Radial runout ≤ 0,003 mm

d1

d2

x1

Balanced G6.3 at 18 000 min-1

ER 11 11 16 16 20 20 25 25

Range 0.5 - 7 0.5 - 7 0.5 - 10 0.5 - 10 1 - 13 1 - 13 1 -16 1 - 16

x1 100 160 100 160 100 160 100 160

d1 16 16 22 22 28 28 35 35

Code ER11.D55.100M ER11.D55.160M ER16.D55.100M ER16.D55.160M ER20.D55.100M ER20.D55.160M ER25.D55.100M ER25.D55.160M

50

Form AD+B

35

DIN ISO 7388-1 (DIN 69871)

Morse taper holders for mills x1

d1

Radial runout ≤ 0,005 mm Balanced G6.3 at 18 000 min-1

50

Form AD+B

MK 1 2 3 3 4 5

x1 45 60 65 150 70 100

d1 25 32 40 40 48 63

Code MK1A.D55.045 MK2A.D55.060 MK3A.D55.065 MK3A.D50.150A MK4A.D55.070 MK5A.D55.100

Morse taper holders for drills x1

d1

Radial runout ≤ 0,005 mm Balanced G6.3 at 18 000 min-1

50

Form AD+B

36

MK 1 2 3 4 5

x1 45 60 65 95 105

d1 25 32 40 48 63

Code MK1B.D55.045 MK2B.D55.060 MK3B.D55.065 MK4B.D55.095 MK5B.D55.105

DIN ISO 7388-1 (DIN 69871)

Threaded shank milling cutter holders x1 A

d3 d2 M

Radial runout ≤ 0,003 mm Balanced G2.5 at 25 000 min-1

M M8 M8 M8 M10 M10 M10 M12 M12 M12 M16 M16 M16 M16

A 50 100 150 50 100 150 50 100 150 50 100 150 200

x1 69 119 169 69 119 169 69 119 169 69 119 169 219

d2 13 13 13 18 18 18 21 21 21 29 29 29 29

d3 20 25 30 24 32 40 23 33 47 32 42 45 55

Code EF08.D55.069 EF08.D55.119 EF08.D55.169 EF10.D55.069 EF10.D55.119 EF10.D55.169 EF12.D55.069 EF12.D55.119 EF12.D55.169 EF16.D55.069 EF16.D55.119 EF16.D55.169 EF16.D55.219

50

Form AD+B

37

DIN ISO 7388-1 (DIN 69871)

Combi shell mill holders for milling cutters d2

Radial runout ≤ 0,003 mm

d1

x1

Balanced G6.3 at 18 000 min-1 l1

50 Form AD

38

d1 16 16 16 16 22 22 22 22 27 27 27 27 32 32 32 32 40 40 40 40 50

x1 55 100 150 200 55 100 150 200 55 100 150 200 55 100 150 200 55 100 150 200 70

x2 45 90 140 190 43 88 138 188 43 88 138 188 41 86 136 186 41 86 136 186 54

d2 32 32 32 32 40 40 40 40 48 48 48 48 58 58 58 58 70 70 70 70 90

x2

l2 27 27 27 27 31 31 31 31 33 33 33 33 38 38 38 38 41 41 41 41 46

Code KD16.D50.055 KD16.D50.100 KD16.D50.150 KD16.D50.200 KD22.D50.055 KD22.D50.100 KD22.D50.150 KD22.D50.200 KD27.D50.055 KD27.D50.100 KD27.D50.150 KD27.D50.200 KD32.D50.055 KD32.D50.100 KD32.D50.150 KD32.D50.200 KD40.D50.055 KD40.D50.100 KD40.D50.150 KD40.D50.200 KD50.D50.070

DIN ISO 7388-1 (DIN 69871)

Shell mill holders for cutters with driving slot Internal coolant supply

x1

Radial runout ≤ 0,003 mm

d1

d2

l1

Balanced G6.3 at 18 000 min-1

x2

d1 16 16 16 16 22 22 22 22 27 27 27 27 32 32 32 32 40 40 40 40 50 60

x1 35 100 160 200 35 100 160 200 35 100 160 200 35 100 160 200 50 100 160 200 120 70

l1 17 17 17 17 19 19 19 19 21 21 21 21 24 24 24 24 27 27 27 27 30 40

d2 38 38 38 38 50 50 50 50 50 50 50 50 78 78 78 78 89 89 89 89 129 129

Code AD16.D55.035 AD16.D55.100 AD16.D55.160 AD16.D55.200 AD22.D55.035 AD22.D55.100 AD22.D55.160 AD22.D55.200 AD27.D55.035 AD27.D55.100 AD27.D55.160 AD27.D55.200 AD32.D55.035 AD32.D55.100 AD32.D55.160 AD32.D55.200 AD40.D55.050 AD40.D55.100 AD40.D55.160 AD40.D55.200 AD50.D55.120 AF60.D50.070

50

Form AD+B

39

DIN ISO 7388-1 (DIN 69871)

Holders for indexable inserts drills d2

Radial runout ≤ 0,005 mm

d1

x1

Balanced G6.3 at 18 000 min-1

50

Form AD+B

d1 20 25 32 40

x1 70 70 75 80

d2 40 45 52 60

Code VB20.D55.070 VB25.D55.070 VB32.D55.070 VB40.D55.080

Quick-change tapping head d1

x1

Length compensation in compression and tension

50 Form A

40

Tap size M3 - M14 M6 - M24 M14 - M33 M22 - M48

Compensation ± 7.5 ± 12.5 ± 20.0 ± 22.5

Insert size 1 2 3 4

x1 74 98 159 175

d1 36 53 78 96

Code GN12.D50.074 GN20.D50.098 GN33.D50.159 GN48.D50.175

DIN ISO 7388-1 (DIN 69871)

HV drill chucks for RH and LH rotation x1

d1

Radial runout ≤ 0,02 mm Balanced G6.3 at 25 000 min-1

mm 1 - 16

x1 80

d1 51

Code HV16.D50.080

50 Form AD

Integrated precision drill chuck with Hexagonal key lock.

For drilling, milling, reaming and tapping.

Through coolant.

Drill chuck slipping impossible due to chuck being screwed with the holder body.

Compact design, enhanced reach.

NC drill chucks for RH rotation x1

Special wrench supplied. d1

Radial runout ≤ 0,03 mm Balanced G6.3 at 12 000 min-1

mm 1 - 13 3 - 16

x1 80 97

d1 54 57

Code NC13.D50.080 NC16.D50.097

50 Form A

Integrated drill chuck with high clamping force achieved through special wrench 2x chucking torque vs. hand tightening Drill bit slipping nearly impossible Drill chuck slipping impossible due to chuck being screwed with the holder body.

Compact design, external coolant supply.

Range up to 8, 10, 13 or 16 mm.

41

DIN ISO 7388-1 (DIN 69871)

Blank bars x1

Machineable soft body.

d1

Cone and flange hardened and finished.

Pre-balanced

50 Form AD

d1 95.5 95.5

x1 160 250

Code RL95.D50.160 RL95.D50.250

Test bars x1

Test certificate and protective case supplied.

d1

Precisely ground length and diameter.

Radial runout ≤ 0,003 mm

50 Form A

42

d1 63

x1 250

Code TB63.D50.250

© SAB d.o.o.

2021

Find additional information and product catalogues

www.sab.hr

SAB d.o.o.

Podborska 1b / 43500 Daruvar tel. + 385 43 675 850 fax. + 385 43 334 700 sab@sab.hr / www.sab.hr Note: Product photos and illustrations are not binding. Product descriptions, technical specifications and dimensions are binding only when explicitly agreed upon. We reserve right to make technical modifications as well as price changes. We take no liability for print or type errors. Only our terms and conditions are valid. 02/2021