Installation instructions screw

Page 1

Installation Instructions Screw Mounted Lights

Models beginning: D0-LIN80, D0-LUI80, D0-MICRO, D0-MACRO, D0-POINT, D0-TEC, D3-DIA85, D4-CRAT, D4-DIA05, D5-CHAR, D5-LUI55, D5-TEC, D6-LIN80, D6-LUI80, Y0-CARPI, Y0-CITY, Y0- COMO, Y0-CORFU, Y0-FALK, Y0-KRIOS, Y0-LEDA, Y0-POLAR, Y0-TEC, Y1-LECCE, Y1-LUCCA, Y1-SMART, Y2-STORM, Y2-TORNA The following instructions are provided to assure safe installation and operation of the LED light. The installer is responsible for following all national electrical code requirements and/or any state of local code requirements. INSTALLATION SHOULD BE PERFORMED BY A CERTIFIED ELECTRICIAN. Light/Family

Cutout (mm/in)

Mounting Holes

Light/Family

Cutout (mm/in)

Mounting Holes

Light/Family

Cutout (mm/in)

Mounting Holes

D0-LIN35 D0-LUI35 D0-POINT D0-MICRO D0-MACRO D0-TEC D3-DIA85 D4-CRAT D4-DIA05 D5-LUI55

185/7.28 185/7.28 55/2.17 26/1.02 26/1.02 53/2.09 67/2.64 98/3.86 82/3.23 113/4.45

3 3 2 2 2 3 3 4 3 3

D5-TEC D6-LIN80 D6-LUI80 Y0-CARPI* Y0-CITY* Y0-COMO* Y0-CORFU* Y0-FALK Y0-FALKM Y0-FALKB

74/2.91 133/5.24 133/5.24 25/0.98 25/0.98 25/0.98 25/0.98 52/2.05 69/2.72 82/3.23

3 3 3 2 2 2 2 3 3 3

Y0-LEDA Y0-KRIOS Y0-POLAR Y0-TEC Y1-LECCE* Y1-LUCCA* Y1-SMART Y2-STORM Y2-TORNA

26/1.02 19/0.75 19/0.75 26/01.02 25/0.98 25/0.98 19/0.75 26X53/1.02X2.09 32/1.26

2 2 2 3 2 2 2 2 2

* Diameter is only to accomidate attached driver FOR WOOD/HARD SURFACE INSTALLATION 1. Select a suitable location where the light is to be installed. 2. Begin by cutting/drilling a hole for recessing the light (ILLUSTRATION 1). Please refer to cutout dimension/mounting holes matrix above for diameter of cut out. Proper cut out size is critical to allow proper surface area to secure screws for installation. 3. Wires should be run to the location the light is to be installed prior to installation. If a third party driver is to be used, please reference the supplimental guide as well as follow all manufacture’s installation instructions. 4. Make sure all power is off at the location where the light is to be installed. 5. Remove outer trim ring by gripping securely and rotating the trim in a counter clockwise direction (ILLUSTRATION 2a) or gripping the trim ring firmly and pulling away from the housing (ILLUSTRATION 2b). This will expose the mounting holes. Place trim ring in a secure area to avoid damaging the finish. 6. Hold the light in the exact location where it will be mounted and mark the holes for the mounting screws (ILLUSTRATION 3). Please refer to cutout dimension/mount holes matrix above for number of mounting holes. 7. Now remove the light from the installation location and drill appropriately sized pilot holes for the mounting screws being used. ** MAKE SURE ALL POWER IS TURNED OFF BEFORE MAKING ANY ELECTRICAL CONNECTIONS ** 8. Connect the lead wires for the light based on the application (24V power supply, Cantalupi Single Channel Dimmer, compatable driver/dimmer, etc.) (ILLUSTRATION 4). This step should be completed before final installation of the light. ** LIGHTS SHOULD NEVER BE LEFT HANGING BY LEAD WIRES AS THIS COULD DAMAGE ELECTRICAL COMPONENTS HOUSED IN THE ATTACHED DRIVER OR LIGHT ** 9. Replace the light base, without the trim ring, into the recessed area and secure with screws in pre-drilled pilot holes from step 6 (ILLUSTRATION 6). 10. Finally, realign the trim ring onto base of light and rotate clockwise to lock into place (ILLUSTRATION 7a) or firmly push the trim ring into the core (ILLUSTRATION 7b). FOR DRYWALL INSTALLATION (optional drywall kit if needed) 1. Select a suitable location where the light is to be installed. 2. Begin by cutting/drilling a hole for recessing the light (ILLUSTRATION 1). Please refer to cutout dimension/mounting holes matrix above for diameter of cut out. Proper cut out size is critical to allow proper surface area to secure screws for installation. 3. Wires should be run to the location the light is to be installed prior to installation. If a third party driver is to be used, please reference the supplimental guide as well as follow all manufacture’s installation instructions. 4. Make sure all power is off at the location where the light is to be installed. 5. Remove outer trim ring by gripping securely and rotating the trim in a counter clockwise direction (ILLUSTRATION 2a) or gripping the trim ring firmly and pulling away from the housing (ILLUSTRATION 2b). This will expose the mounting holes. Place trim ring in a secure area to avoid damaging the finish. 5. Hold the light in the exact location where it will be mounted and mark the holes for the mounting screws (ILLUSTRATION 3). Please refer to cutout dimension/mount holes matrix above for number of mounting holes. 6a. For installation with drywall kit: i. Remove the light from the installation site and drill appropriately sized pilot holes for the mounting screws being used. ii. Insert the metal drywall supports, included with your order, carefully aligning the pre-drilled holes in the drywall supports with the pilot holes from step 6a.ii (ILLUSTRATION 5). Page 1

Illustration 1

Illustration 2a

Illustration 2b

Illustration 3

Cantalupi USA, Inc. • 616 Druid Road, East • Clearwater, FL 33756 • (727) 462-2526 • (727) 683-9720 fax • www.cantalupiusa.com • technical@cantalupiusa.com


** MAKE SURE ALL POWER IS TURNED OFF BEFORE MAKING ANY ELECTRICAL CONNECTIONS ** ii. Connect the lead wires for the light based on the application (24V power supply, Cantalupi Single Channel Dimmer, compatable driver/dimmer, etc.) (ILLUSTRATION 4). This step should be completed before final installation of the light. iii. Replace the light base, without the trim ring, into the recessed area and align with metal drywall supports and pilot holes from previous steps. Secure with screws through supports and drywall (ILLUSTRATION 6). 6b. For installation without drywall kit: ** MAKE SURE ALL POWER IS TURNED OFF BEFORE MAKING ANY ELECTRICAL CONNECTIONS ** i. Connect the lead wires for the light based on the application (24V power supply, Cantalupi Single Channel Dimmer, compatable driver/dimmer, etc.)(ILLUSTRATION 4). This step should be completed before final installation of the light. i. While holding the light base in place, without the trim ring, into the recessed area, secure with screws through mounting holes marked in Step 5 (ILLUSTRATION 6). ** LIGHTS SHOULD NEVER BE LEFT HANGING BY LEAD WIRES AS THIS COULD DAMAGE ELECTRICAL COMPONENTS HOUSED IN THE ATTACHED DRIVER OR LIGHT ** 7. Finally, realign the trim ring onto base of light and rotate clockwise to lock into place (ILLUSTRATION 7a) or firmly push the trim ring into the core (ILLUSTRATION 7b).

Illustration 4

FOR PLASTER FRAME INSTALLATION 1. Plaster frame should installed by a qualified contrator prior to installation of light. 2. Once plaster frame is installed, follow instructions for drywall installation without drywall kit. FOR CONCRETE POUR INSTALLATION (requires concrete pour can) 1. Place concrete pour can in desired position/location using concrete forms, as per design. 2. Wires should be run to the location the light is to be installed prior to installation. If a third party driver is to be used, please reference the supplimental guide as well follow all manufacture’s installation instructions. 3. Make sure all power is off at the location where the light is to be installed. 4. Pour concrete as per manufacturer’s intructions. Pouring of concrete around forms should be completed by a professional contractor. 5. Concrete should be allowed to set completely before proceeding. 6. Remove outer trim ring by either gripping securely and rotating the trim in a counter clockwise direction (ILLUSTRATION 2a) or gripping the trim ring firmly and pulling away from the housing (ILLUSTRATION 2b). This will expose the mounting holes. Place trim ring in a secure area to avoid damaging the finish. 7. Hold the light in the exact location where it will be mounted and mark the holes for the mounting screws (ILLUSTRATION 3). Please refer to cutout dimension/mount holes matrix above for number of mounting holes. 8. Now remove the light from the installation location and drill appropriately sized pilot holes for the mounting screws being used. 9. Connect the lead wires for the light based on the application (24V power supply, Cantalupi Single Channel Dimmer, compatable driver/dimmer, etc.) (ILLUSTRATION 4). This step should be completed before final installation of the light. 10. Replace the light base, without the trim ring, into the recessed area and secure with screws in pre-drilled pilot holes from step 6 (ILLUSTRATION 6). 11. Finally, realign the trim ring onto base of light and rotate clockwise to lock into place (ILLUSTRATION 7a) or firmly push the trim ring into the core (ILLUSTRATION 7b).

Illustration 5

Illustration 6

EXAMPLES OF LIGHT HOUSINGS

Illustration 7a

Example Example

Example

Example

Illustration 7b

Page 2 Cantalupi USA, Inc. • 616 Druid Road, East • Clearwater, FL 33756 • (727) 462-2526 • (727) 683-9720 fax • www.cantalupiusa.com • technical@cantalupiusa.com Updated July 08, 2013


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.