Aluminum Extrusion

A L U M I N U M & E X T R U S I O N S

F O R T H E S I G N I N D U S T R Y

ITEM- NUMBER

DESCRIPTION

ITEM- NUMBER

DESCRIPTION

ALUMINUM

2T12520020020

TUBE ⅛” x 2” x 2” x 20’ ALUM.

2T12520020020

TUBE ⅛” x 2” x 2” x 20’ ALUM.

2T12512512520

TUBE ⅛” x 1¼” x 1¼” x 20’ ALUM.

2T12512512520

TUBE ⅛” x 1¼” x 1¼” x 20’ ALUM.

2T12515015020

TUBE ⅛” x 1½ x 1½ x20’ ALUM.

2T12515015020

TUBE ⅛” x 1½ x 1½ x 20’ ALUM.

2TO6315015020

TUBE 1/16” x 1½ x 1½ x 20’ ALUM.

2TO63115015020

TUBE 1/16” x 1½ x 1½ x 20’ ALUM.

2TO6310010020

TUBE 1/16” x 1” x 1” x 20’ ALUM.

2TO6310010020

TUBE 1/16” x 1” x 1” x 20’ ALUM.

2TO6320020020

TUBE 1/16” x 2“ x 2” x 20’ ALUM.

2T12510010020

TUBE ⅛” x 1” x 1” x 20’ ALUM.

2T12510020020

TUBE ⅛” x 1” x 2” x 20’ ALUM.

2T12507515020

TUBE ⅛” x ¾” x ¾ “ x 20’ ALUM.

2T06307507520

TUBE 1/16” x ¾” x ¾” x 20’ ALUM.

2T12520020010

TUBE ⅛” x 2” x 2” x 10’ ALUM.

2T06307507510

TUBE 1/16” x ¾” x ¾” x 10’ ALUM.

2T06310010010

TUBE 1/16” x 1” x 1 “ x 10’ ALUM.

2T12515015010

TUBE ⅛ X 1½” x 1½” x 10’ ALUM.

2T06315015010

TUBE1/16 x 1½” x 1½” x 10’ ALUM.

212507515010

TUBE ⅛ x ¾” x 1½” x 10’ ALUM.

212510020010

TUBE ⅛ x 1” x 2” x 10’ ALUM.

212510010010

TUBE ⅛ x 1” x 1” x 10’ ALUM.

2T06320020010

TUBE1/16 x 2” x 2” x 10’ ALUM.

ITEM- NUMBER

DESCRIPTION

Custom cutting available ITEM- NUMBER

DESCRIPTION

2CS-MFTS6

Monoclic Spring

2CSS-10-3-20

CSS-10-3x20’ B-Lite Gold

2CS-ERP11

Easyclic Spring Rear Profile

2CSS-11-4-20

CSS-11-4x20’ B-Lite Chrome

2CS-ELP13

Monoclic Corner Angle

2CSS-11-3-20

CSS-11-3x20’ B-Lite Gold

2CS-EFT12

Easyclic Spring Front Trim

2CSS-11-1-20

CSS-11-1x20’ Mill Finished

2CSS-12-3-20’

CSS-12-3-20’ B-Lite Gold

2CSS-16-26’1”

CSS-16x26’1” 6063 T-5

2CSS-15-26’1”

CSS-15x26’1” 6063 T-5

2CSS-14-1-20

CSS-14 1x20’ Mill Finished

2CSS-13-1-20

CSS-13 1x20’ Mill Finished

2CSS-13-1-20

CSS-13 1x20’ Mill Finished

ITEM- NUMBER

DESCRIPTION

2BAR12510020

Rect. Bar ⅛” x 1” x 20’

2BAR18812520

Rect. Bar 3/16” x 1” x 20’

ALUMINUM

ITEM- NUMBER

DESCRIPTION

ITEM- NUMBER

DESCRIPTION

2A18810010020

ANGLE 3/16” x 1” x 1” x 20’ ALUM.

2A12520020010

ANGLE ⅛” x 2“ x 2” x 10’ ALUM.

2A18820020020

ANGLE 3/16” x 2” x 2” x 20’ ALUM.

2A18820020020

ANGLE 3/16” x 2” x 2” x 10’ ALUM.

2A12520010020

ANGLE ⅛” x 1½” x 1½” x 20’ ALUM.

2A12520010010

ANGLE ⅛” x 2” x 1” x 10’ ALUM.

2A06320020020

ANGLE 1/16” x 2” x 2 “ x 20’ ALUM.

2A06310010010

ANGLE 1/16” x 1” x 1 “ x 10’ ALUM.

2A12507507520

ANGLE ⅛ x 3/4” x 3/4” x 20’ ALUM.

2A12515015010

ANGLE ⅛ x 1½” x 1½” x 10’ ALUM.

2AO6315015020

ANGLE 1/16” x 1½“ x 1½” x 20’ ALUM.

2AO6315015010

2A06307507520

ANGLE 1/16” x 1½“ x 1½” x 10’ ALUM.

ANGLE 1/16 x ¾” x ¾ “ x 20’ ALUM.

2A12507507510

ANGLE ⅛ x ¾” x ¾” x 10’ ALUM.

2A37550050025

ANGLE ⅜” x 5” x 5” x 25’ ALUM.

2A12510010015

ANGLE .125 x 1” x 1” x 15’ ALUM.

2A37560040025

ANGLE ⅜” x 6” x 4” x 25’ ALUM.

2A06305005010

ANGLE 1/16 x ½” x ½” x 15’ ALUM.

2A37560060025

ANGLE ⅜” x 6” x 6 “ x 25’ ALUM.

2A06307507510

ANGLE 1/16 x ¾” x ¾” x 10’ ALUM.

2A25020020020

ANGLE ¼ x 2” x 2” x 20’ ALUM.

2A06320020010

ANGLE 1/16 x 2” x 2” x 10’ ALUM.

2A12520020020

ANGLE ⅛” x 2“ x 2” x 20’ ALUM.

2A12515015020

ANGLE ⅛” x 1½” x 1½” x 20’ ALUM.

2A125210010020

ANGLE ⅛” x 1” x 1” x 20’ ALUM.

2A06310010010

ANGLE 1/16” x 1” x 1 “ x 10’ ALUM.

2A06305005020

ANGLE 1/16 x ½” x ½” x 20’ ALUM.

2A06307507508

ANGLE 1/16 x ¾” x ¾” x 8’ ALUM. 2RT250035144

Drawn .250 x.035 x 144 3003 H14

PLANCHAS DE ALUMINIO APLICACIONES: R贸tulos, Paneles, Exhibidores POP, Cajas Lum铆nicas, Vallas.

EXTRUSIONS

ALUMINUM SHEETS

ITEM-NUMBER

280-48144-111 280-48120-111 280-48096-111 263-48144M111 263-48120M111 263-48120-111 263-48096M111 263-48096-111 250-48144-111 250-48120-111 250-48096-111 240-60144-111 240-60120-111 240-48144-111 240-48144M111 240-48120M111 240-48120-111 240-4896M111 240-48096-111 232-60144-111 232-60096-111 232-60096M111 232-60120-111 232-60120M111 232-48120M111 232-48144-111 232-48144M111 232-48120-111 232-48096-111 240-60096-111 263-60096M111 263-60120M111 263-60144M111

DESCRIPTION

CLASS-CODE

.080x48x144 White /white .080x48x120 White /white .080x48x96 White /white .063x48x144 White Masked .063x48x120 White/white Masked .063x48x120 White Un Masked .063x48x96 White/white Masked **USAR 63-48096M111***** .050x48x144 Masked White/white .050x48x120 Masked White/white .050x48x96 Masked White/white .040x60x144 White/ White .040x60x120 White /white .040x60x144 White /white .040x60x144 White /white Masked .040x60x120 Masked White /white .040x60x120 White /white .040x60x96 Masked White /white .040x60x96 White /white .032x60x144 White /white .032x60x96 White /white .032x60x96 White /white Masked .032x60x120 White /white .032x60x120 White /white Masked .032x48x120 Masked White /white .032x48x144 White /white .032x48x144 Masked White /white .032x48x120 White /white .032x48x96 White /white .032x60x96 White /white .063x60x96 White /white Masked .063x60x120 White /white Masked .063x60x144 White /white Masked

ITEM-NUMBER

DESCRIPTION

263-48120-102 250-48120-101 240-48120-131 240-48120-156 240-48120-171 240-48120-193 240-48120-105 240-48120-101 240-48120-103 240-48120-104 240-48096-131 240-48096-156 240-48096-171 240-48096-110 240-48096-101 240-48096-102 240-48096-103 240-48096-104 240-48096-235 240-48120-235

.063x48x120 .050x48x120 .040x48x120 .040x48x120 .040x48x120 .040x48x120 .040x48x96 .040x48x120 .040x48x144 .040x48x120 .040x48x96 .040x48x144 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x120

100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

CLASS-CODE

Matte Black /white Raven Black /white Red /white Caut. Yellow/ White Ivy Green/white Brigth Puple/white Orange/white Raven Black/white Heron Blue/white Heron Blue/heron Red/white Caut. Yellow/ White Ivy Green/white Raven Black/black Raven Black /white Matte Balck /white Heron Blue /white Hero Blue/hero Med Gray/charco Med Gray/charco

101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101

ITEM-NUMBER

290-48096-400 290-48120-400 290-48144-400

ESPESOR ALTO ANCHO

.090 x 48 x 96 .090 x 48 x 120 .090 x 48 x 144 .080 x 60 x 96 .080 x 60 x 120 .080 x 60 x 120 .080 x 48 x 144 .080 x 48 x 144 .080 x 48 x 96 .080 x 48 x 120 .080 x 48 x 120 .080 x 36 x 144 .080 x 48 x 96

263-60144-52 263-60096-52 263-60120-52 263-48144-52 263-48120-52 263-48096-52 236-36096-52 263-36120-52 263-36144-52

.063 x 60 x 144 .063 x 60 x 96 .063 x 60 x 120 .063 x 48 x 144 .063 x 48 x 120 .063 x 48 x 96 .063 x 36 x 96 .063 x 36 x 120 .063 x 36 x 144

263-48144-400 263-48120-400 263-48096-400 263-36144-400

.063 x 48 x 144 .063 x 48 x 120 .063 x 48 x 96 .063 x 36 x 144

250-48144-400 250-48144-52 250-48120-400 250-48120-52 250-48096-400 250-48096-52 250-36096-52 250-36120-52 250-36144-52

.050 x 48 x 144 .050 x 48 x 144 .050 x 48 x 120 .050 x 48 x 120 .050 x 48 x 96 .050 x 48 x 96 .050 x 36 x 96 .050 x 36 x 120 .050 x 36 x 144

240-48144-400 240-48120M400 240-48120-400 240-48096M400 240-48096-400 240-36120-400

.040 x 48 x 144 .040 x 48 x 120 .040 x 48 x 120 .040 x 48 x 96 .040 x 48 x 96 .040 x 36 x 120

232-48120-400 232-48096-400 232-36120-400

.032 x 48 x 120 .032 x 48 x 96 .032 x 36 x 120

2250-48096-40

.025 x 48 x 96

216-34076-400 216-36076-400

5052 5052 5052 5052 5052 5052 5052-H32 5052-H32 5052-H32 5052-H32 5052-H32 5052-H32 5052 5052 5052

ITEM-NUMBER

ESPESOR ALTO ANCHO

2190-48120-40 2188-48120-40 2188-48096-40

.190 x 48 x 120 .188 x 48 x 120 .188 x 48 x 96

2125-60192-52 2125-60120-52 2125-60144-52 2125-60156-52 2125-60096-52 2125-48168-52 2125-48144-40 2125-48144-52 2125-48156-52 2125-48096-40 2125-48096-52 2125-48120-40 2125-48120-52 2125-36120-52 2125-36144-52 2125-48180-52

.125 x 60 x 192 .125 x 60 x 120 .125 x 60 x 144 .125 x 60 x 156 .125 x 60 x 96 .125 x 48 x 168 .125 x 48 x 144 .125 x 48 x 144 .125 x 48 x 156 .125 x 48 x 96 .125 x 48 x 96 .125 x 48 x 120 .125 x 48 x 120 .125 x 36x1 20 .125 x 36 x 144 .125 x 48 x 180

26061T6

1/2” x 48 x 144 ALUM. PLATE

2250-48192-6061 2125-48096-3003 2188-48192-3003

4’ x 16’ ALUM. BRHIGT TREAD PLT 4’ x 8’ ALUMBRIGHT TREAD PLT 4’ x 16’ ALUM. BRHIGT TREAD PLT

COLOR

5052 5052 5052 5052 5052 5052 5052 5052

1

ALUMINUM

280-60096-52 280-60120-400 280-60120-52 280-48144-400 280-48144-52 280-48096-52 280-48120-400 280-48120-52 280-36144-52 280-48096-400

COLOR

5052 5052 5052

5052 5052 5052 5052 5052 5052

.016 x 34 x 76 MILL FINISHED 30 .016 x 34 x 76 MILL FINISHED 30

ITEM-NUMBER 240-48120M231

ESPESOR ALTO ANCHO

240-48120M235 240-48120-230

.040 x 48 x 120 MIRROR CLEAR .040 x 48 x 120 B.B. CLEAR ANODIZED .040 x 48 x 120 CLEAR SATIN ANODIZED

240-48120M236 240-48120-232

.040 x 48 x 120 B.B. GOLD ANODIZED .040 x 48 x 120 GOLD SATIN ANODIZED

240-48096-240

.040 x 48 x 96

BRONZE ANODIZED

COLOR

ALUMINUM ITEM- NUMBER

DESCRIPTION

Custom cutting available

2SIGNCOMP2075

2¼” Retainer 24’5”

2SIGNCOMP2055

1½” Retainer 24’5”

2SIGNCOMP2056-20

Econo Molding 20’

2SIGNCOMP2056

Econo Molding 24’5”

2SIGNCOMP5116

040 x 10 x ¼ WB Raceway Cover

2SIGNCOMP2056P

Econo Molding 24’5”

2SIGNCOMP4580

Signcomp R/C Sing Face Bleed

2SIGNCOMP2034

Single Face Filler 24’5” Econ.

2SIGNCOMP4000

Signcomp Single Face Body 9” R

2SIGNCOMP2034P

Single Face Filler 24’5” Econ.

2SIGNCOMP1985

Socket Raceway 24’5”

2SIGNCOMP1987

Transformer Raceway Cover 24’2”

2SIGNCOMP1986

Socket Raceway Cover 24’2”

2SIGNCOMP1948

¾” Wall Frame 24’2”

2SIGNCOMP1949

1¼” Wall Frame 24’2”

2SIGNCOMP1981

2 PC Trans Raceway-Front 24’2”

2SIGNCOMP2075

2¼ Dual Frame Cover 24’5”

2SIGNCOMP1982

2 PC Trans Raceway-Back 24’2”

2SIGNCOMP1986

Transformer Raceway Cove 24’2”

2SIGNCOMP4540

Signcomp R/C Med. Body Dual

2SIGNCOMP4550

Signcomp R/C Med. B Bleed

2SIGNCOMP4560

Single Face Body 9” R/C

2SIGNCOMP4220

Signcomp 2.25 Dual Rad. Cover

2SIGNCOMP4260P

Signcomp Bleed Tension Cover

2SIGNCOMP4280

Signcomp 1.5” Retainer R/C

2SIGNCOMP4200

Signcomp Dual Frame R/C

2SIGNCOMP2122

Bleed Retro Frame Cover 24’5”

2SIGNCOMP2128

2¾” Divider 24’5”

2SIGNCOMP4280

Signcomp 1.5” Retainer R/C

2SIGNCOMP1941

2 Part Large Outer Frame 24’5”

2SIGNCOMP1959

2 Part Large Inner Frame 24’6”

2SIGNCOMP1989

Trans Raceway Mounting Clip

2SIGNCOMP5290-1

Raceway Cvr.Screw 2Pt Retainer

2SIGNCOMP1007

DESCRIPTION S1 3¼” ROUND POST 24’

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1210

S3 3¼” RADIUS POST 24’

ITEM- NUMBER

DESCRIPTION

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1100

S2 2” SQUARE POST 24’

2SIGNCOMP1233

S3 3¼” SQUARE POST 24’

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1260

S3 3¼” SLIDE BODY 24’2”

ITEM- NUMBER 2SIGNCOMP1120

DESCRIPTION

EXTRUSIONS

ITEM- NUMBER

S2 BLEED BODY 24’ 2”

ITEM- NUMBER

DESCRIPTION

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1200

S2/S3 REVEAL 24’

2SIGNCOMP1270

S3 3¼” BLEED BODY 24’2”

EXTRUSIONS

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1500

S7 7” RADIUS POST 24’

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1510

S7 7” RECTANGULAR POST 24’

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1592

S7 HINGE BODY 24’2”

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1662

1 1¼DIVIDER 24’

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1666

INSERT RETAINER 16’1”

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1550

S7 REVEAL 24’

ITEM- NUMBER

DESCRIPTION

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1570

S7 7” BLEED BODY 24’2”

2SIGNCOMP1668

INSERT DIVIDER 16’

EXTRUSIONS

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1671

6” RADIUS ¼ ROUND END 24’2”

7-1/2” 1/4”

1/4” Joiner Bracket

1/4” Corner Angle Slot

1/4” Steel Mounting Plate 5-3/16”

W ater Relief Channel

Raceway Cover Ta b

Inner Body Flanges

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP2015

MEDIUM BODY 24’5”

3/8” Oversized Hole 10-3/4”

1/4” Joiner Bracket Slot

Ballast Bracket Slots

1/4”

8-7/16”

Raceway Cover Ta b

Hinge Screw

Part #5170

W ater Relief Channel

Inner Body Flanges

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP2005

WIDE BODY 24’ 5”

1/4” Corner Angle Part #5312

Closure Screw

Part #5180

1-3/4”

1-11/16”

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP2040

RETRO BODY 24’5”

Corner Angle Screw

Part #5218

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1592

S7 HINGE BODY 24’2”

ITEM- NUMBER

DESCRIPTION

2SIGNCOMP1668

INSERT DIVIDER 16’

T E N S I O N I N G

S Y S T E M S

F O R

F L E X I B L E

F A C E S

EXTRUSIONS

Sign Cabinet Body Extrusions Single Face Body 24’5” 2SIGNCOMP2025

6-1/8”

Retro Body 24’5”

1/4”

2SIGNCOMP2040

3-15/16” .040 aluminum back

Hinge Screw 2SIGNCOMP5170

1-3/4”

1-11/16”

Medium Body Part #2015

7-1/2”

1/4” 5-3/16” Screw 2SIGNCOMP5170

Wide Body 24’5” 2SIGNCOMP2005

10-3/4”

1/4” 8-7/16”

Hingeable Retainer Extrusions Bleed Tension Frame Cover 24’5” 2SIGNCOMP2095

Tension Frame 24’5”

Dual Frame 24’5”

1½” Tension Frame Cover

2¼” Dual Frame Cover

2SIGNCOMP2065

2SIGNCOMP2085

2SIGNCOMP2084

2SIGNCOMP2075

Frame Brace 2SIGNCOMP5350

Frame Support Tube 2SIGNCOMP2175

Frame Brace 2SIGNCOMP5350

Frame Support Tube 2SIGNCOMP2175

T E N S I O N I N G

S Y S T E M S

F O R

F L E X I B L E

F A C E S

2” Retro Frame 24’5”

EXTRUSIONS

Retro Frame Extrusions Bleed Retro Frame

2SINGCOMP2112

2SIGNCOMP2105

2-3/8” Retro Frame Cover

2SIGNCOMP2115 (Optional Brake Form Cover)

Frame Brace 2SIGNCOMP5350

Frame Support Tube 2SIGNCOMP2175

Frame Brace 2SIGNCOMP5350

Flat Bleed Retro Frame

Wall Mount Retro Frame

Flat Bleed Retro Frame Cover

Wall Mount Retro Frame Cover

Part #2104

Frame Support Tube 2SIGNCOMP2175

2SIGNCOMP2090

Part #2121

NOTE: Wall Mount Retro Tensioning Tool, 2sigcomp5137 required.

2SIGNCOMP2091

Flat Bleed Retro Frame

Flat Bleed Retro Frame

Extended Bleed Retro Cover

1-1/2” Flat Retro Frame Cover

Part #2104

Part #2104

Part #2123

Part #2125

Retro Fascia Frame Extrusions Bleed Fascia Frame 24’ 5”

1-1/2” Fascia Frame 24’5”

Part 2SIGNCOMP2092

(Optional Brake Form Cover)

2SIGNCOMP2094

Cover Screw 2SIGNCOMP5195

Corner Key 2SIGNCOMP5210

(Optional Brake Form Cover)

Frame Corner Angle 2SIGNCOMP5305 Corner Key 2SIGNCOMP5210

Cover Screw 2SIGNCOMP5195

T E N S I O N I N G

S Y S T E M S

F O R

F L E X I B L E

F A C E S

EXTRUSIONS

Divider Bar Dual Divider 24” 2SIGNCOMP2142

2-1/2” Dual Divider Cover

2SIGNCOMP2146

6” & 9” Radius Cast Aluminum Corners Medium Body

Wide Body

Single Face Body

Dual Frame

with 2-1/4” Dual Frame Cover

Tension Frame

with Bleed Tension Frame Cover

NOTE: The hingeable body and frames are cast aluminum 2-1/4” Dual Frame Cover and Bleed Tension Frame Covers are injection molded polycarbonate, pre-primed ready for paint/top coating.

Hingeable Systems Configurations Medium Body

Single Face Body

Retro Body

13-3/4”

17”

9-1/4”

4-7/8”

Tension Frame

14”

17-1/4”

9-3/8”

4-15/16”

Tension Frame

14-1/2”

17-3/4”

9-5/8”

5-3/16”

Dual Frame

Wide Body

with 2-1/4” Dual Frame Cover

with Bleed Tension Frame Cover

with 1-1/2” Tension Frame Cover

T E N S I O N I N G

S Y S T E M S

F O R

F L E X I B L E

F

A C E S

EXTRUSIONS

The very best flexible face tensioning system.

Easy to use:

Tension Clip

1. FOLD fabric over mandrel.

2. SNAP clip onto mandrel & fabric.

3. INSERT Tension Clip with fabric into either retro frame or hingeable frame. * * * *

2SIGNCOMP5360

No holes to drill.

No fasteners required. Easy to adjust and will not migrate. Absolutely no slippage .

Clips attach to fabric, face side up. Once attached, faces may be rolled for transport or storage.

Simple to tension, quick to release. The Tensioning Tool allows for easy and controlled tensioning force. Tension Clips release from the extruded frame with a standard slotted screwdriver .

Tension Clip Body

Tension Clip Mandrel Face Side Up

of

Side Profile Tension Clip with Fabric

T ool

Tension Clip Mandrel

Tensioning

1. FOLD

T ool Wall Mount Tensioning

Tension Clip Body

2. SNAP

3. INSERT Shown in Retro Frame Part #2112

UL Recognized

Component

System:

The Under writers Laboratory file number is (E136850).

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

EXTRUSIONS

Tensioning System Instructions 2.) Fold the fabric over the mandrel.

D. Tension Clip Attachment 1.) Place the mandrel, smooth side up, on the fabric just inside the clip placement line.

(Illus. 5)

(Illus. 3.)

Illus. 5

3.) Rotate the fabric and mandrel for ward by lifting the edge nearest you to stand the mandrel and fabric up on its edge.

(Illus. 6)

Illus. 3

IMPORTANT - Tension Clips are attached to the fabric graphic side up.

NOTE - The Tension Clip is comprised of two components: The Tension Clip Body and the Tension Clip Mandrel.

(Illus. 4) Illus. 6

Tension Clip Body

4.) With the SignComp logo facing toward you, use thumb pressure to drive one end of the clip body down on to the mandrel and fabric.

(Illus. 7 & 8) (4)

(5) Tension Clip Mandrel

Illus. 4

Illus. 7

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

E. Tension Clip Placement

EXTRUSIONS

Tensioning System Instructions (Illus. 10)

For: Dual Frame, 2” Retro Frame and 1-1/2” Fascia Frame.

Place Tension Clips approximately 6” on center .

5.) Using palm pressure, drive the remaining end of the clip body down onto the mandrel and fabric.

1-1/2” Fascia Frame Part #2094

(Illus. 7, 8, & 9.)

Dual Frame Part #2065

2” Retro Frame Part #2112

For: Tension Frame, Bleed Retro Frame, Flat Bleed Retro Frame, Dual Divider and Bleed Fascia Frame.

Place Tension Clips approximately 5” on center .

Bleed Fascia Frame Part #2092

Tension Frame Part #2085

Bleed Retro Frame Part #2105

Flat Bleed Retro Frame Part #2104

Dual Divider Part #2142

Illus. 8

Illus. 10

Illus. 9

HINT: Do not try to drive both ends of the clip

body down onto the mandrel and fabric at the same time. Snap one end down then the other end.

HINT - Tension Clip Position may be adjusted with out removing the T ension Clip from the fabric.

Slide the clip mandrel in the direction you wish to move the Tension Clip. Follow this by sliding the Tension Clip Body. Repeat this procedure until position adjustment is achieved.

HINT - The Tension Clip may be detached from the fabric by pulling the Tension Clip Body straight off and away from the fabric and Tension Clip Mandrel.

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

EXTRUSIONS

Tensioning System Instructions F. Tensioning 1.) Lay the assembled frame flat with the extruded Tension Channel facing up.

2.) Lay the fabric, with the Tension Clips attached, over the assembled frame graphic side up.

3.) Insert the Tension Clips into the Tension Channel of the assembled frame. Work your way around the frame just starting each clip into the extruded frame as shown.

(Illus. 12 & 13.)

HINT: When pulling on the fabric do not pull directly on the fabric flap or Tension Clip doing so will cause the T ension Clip to pop off. When pulling on the face grasp the fold and pull the face into place.

Illus. 11

4.) Using the Tension Tool, exert a downward for ce onto each Tension Clip, pressing it into the extruded frame as shown.

(Illus. 12 & 13.)

HINT: Just start the Tension Clips in one or two clicks, working your way around the frame. Go back around a second time and apply tension by driving the Tension Clips down into the frame. Do not over tension . Apply just enough tension to achieve a smooth, flat appearance.

G. Tension Tool Use

Illus. 12 Rotate

Hook the Tension Tool tip under the outside rail of the assembled frame. Slide the Tension Tool along the outside rail. With gentle, consistent pressure, force the Tension Clip into place by pressing the “wings� of the Tension Tool downward onto any portion of the Tension Clip.

By pushing or pulling the Tension Tool handle while the Tension Tool tip is inserted under the outside rail, leverage is gained to exert for ce down on to the Tension Clip.

(Illus 12 & 13.)

NOTE: Downward pressure may be applied to either end or the middle of the Tension Clip.

Outside Rail

Illus. 13

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

H. Releasing the Tension and Removing the Tension Clip

or

EXTRUSIONS

Tensioning System Instructions (T ilt) (Rotate)

A standard slotted screwdriver is used to release tension from the installed fabric. Insert the tip of the screwdriver into the recess located at the backside of the Tension Clip. Rotate or tilt the screwdriver to separate the Tension Clip teeth away from the extruded teeth within the frame. This will release the tension or allow the Tension Clip to be removed from the frame by prying or pulling the Tension Clip up & out.

(Illus. 14 &15.)

1.) Insert the screwdriver tip into the Tension Clip recess.

2.) Rotate or tilt the

screwdriver to release the Tension Clip teeth away from the extruded frame.

3.) Remove Tension Clip

by prying or pulling it out and up from the frame.

Illus. 14

I. References

ST RAI G H T

Illus. 15

ANG L ED

T E N SI O N C H A N N E L FR A M E S

T E N SI O N C H A N N E L FR A M E S

D ual Fram e

Ten sion Fram e

Part #2065

Recess on backside

Tension Clip Body

Part #2085

Important Note: It is important to note the stretch factor of the flexible fabric varies considerably for each brand. When tensioning large sign faces (10’ x 10’ or larger) it is advisable to test the stretch factor by using a strip of the same fabric with one tension clip on each end.

Tension Clip Mandrel

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

EXTRUSIONS

Tensioning System Instructions Befor e beginning, thoroughly read all tensioning instructions.

Tools Required: 1.

2.

SignComp Tensioning Tool, part #5135.

Pen or marker .

1

3.

4.

2

Flexible Sign Fabric Requirements

ST RAI G H T

FOR:

TENSION CHANNEL FRAMES

1½” Fascia 24’5” Frame 2SIGNCOMP2094

Dual Frame 24’5” 2SIGNCOMP2065

Razor blade or utility knife.

Standard slotted screw driver.

2” Retro Frame 24’5” 2SIGNCOMP2112

Dual Divider 24’5” SIGNCOMP2142

Tension Clip Requirements

To determine the approximate number of Tension Clips required, measure the outside dimensions of the assembled sign frame. You will require a minimum of two (2) Tension Clips for ever y perimeter foot. Use 6” on center for straight tension channel frames and 5” on center for angled tension channel frames.

12’

6’ To the outside dimensions of any assembled STRAIGHT TENSION CHANNEL FRAME, add 1-1/2” of flexible fabric to all four sides. (Add a total of 3” of fabric to both the height and width dimensions of the assembled frame.)

NOTE: Measure from the center of the Dual Divider .

12’

Outside dimensions = 36’ (perimeter feet) x 12” = 432”.

432” / 6” = 72 Tension Clips for straight tension channel frames. 432” / 5” = 87 Tension Clips for angled tension channel frames.

ANG L ED

FOR:

Example Sign Size

TENSION CHANNEL FRAMES

See page 4, E. Tension Clip Placement for further details.

Bleed Fascia Frame 24’5” 2SIGNCOMP2092

Tension Frame 24’5” 2SIGNCOMP2085

Bleed Retro Frame 24’5” 2SIGNCOMP2105

Flat Bleed Retro Frame Part #2104

To the outside dimensions of any assembled ANGLED TENSION CHANNEL FRAME, add 3” of flexible fabric to all four sides. (Add a total of 6” of fabric to both the height and width dimensions of the assembled frame.)

6’

S I G N

E X T R U S I O N S

A N D

S Y S T E M S

3

Basic Instructions

EXTRUSIONS

Tensioning System Instructions HINT: Angled Tension Channel Frames may be

used as a straight edge to draw the clip placement line and trimmed to size fabric line.

A. Trim the flexible sign fabric to size The fabric is to be cut to the appropriate size. See page 1, 1. Flexible Sign Fabric Requirements.

B. Establish the Tension Clip Placement Line

Bleed Fascia Frame 24’5” 2SIGNCOMP2092

Tension Frame 24’5” 2SIGNCOMP2085

Bleed Retro Frame 24’5” 2SIGNCOMP2105

Flat Bleed Retro Frame Part #2104

IMPORTANT - Address the fabric graphic side up.

The clip placement line is to be located on the graphic side of the fabric.

FOR ALL FRAMES:

Draw or drop the clip placement line 1-1/2” in from the edge of the trimmed to size fabric.

HINT : Straight Tension Channel Frames may be

placed on the fabric and traced along the outside perimeter of the frame to establish the clip placement line. Be sure to add 1-1/2” of fabric outside the clip placement line to establish the trimmed to size fabric.

(Illus. 1 & 2)

IMPORTANT : Be sure to adjust the position of the angled tension channel frame to accommodate the additional fabric required. See Page 1, 1. Flexible Sign Fabric Requirements. ension NOTE: For Large Applications:

For applications larger than 10’, move the T Clip placement line in approximately 1/4” for ever y 5’ increment. For example a 15’ x 15’ Frame Tension Clips are to be placed approximately 1-3/4” in from the trimmed to size fabric. See page 7, important note.

C. Notch the Corners

1½” Fascia Frame 2SIGNCOMP2094

Dual Frame 24’5” 2SIGNCOMP2065

2” Retro Frame 24’5” 2SIGNCOMP2112

Cut away an approximate 2-1/2” square notch from the fabric edge in each of the four corners of the trimmed to size fabric.

HINT :

1½” Tension Clip Placement Line Trimmed to Size Flexible Sign Fabric

Illus. 1

2½” Notched Corner (Discard)

2½”

Illus. 2

1½” ”

2½”

(Graphic Side Up)

Trimmed to Size Flexible Sign Fabric

EXTRUSIONS

SignComp products offer mounting

options

Internal Mounting SystemInboard Posts

Base Plate Mounting

Fabricated base skirts are easily removed for access to mounting plates

Base Plate Mounting

Direct Burial

Wall projection, ceiling mount and sleeve mounting applications are available options

External Mounting SystemOutboard Posts

Base Plate Mounting

Direct Burial W all projection, ceiling mount and sleeve mounting applications are available options

Direct Burial

SignComp’s Insert Panels are: Quickly removable Completely interchangeable Easily replaceable They simply slide in and out after the Insert Panel End Cover is removed.

Illuminated applications Non-illuminated applications Hingeable and Non-hingeable aluminum framework Flush frameless appearance Concealed structural divider

Choice of custom size panels

Custom

Panel

Custom height panels may be placed anywhere on the face Insert

Custom

Insert

Panel

Panel

Panel

Choice of three Extruded Aluminum Insert Panels 4”, 6” and 8” or create custom height Aluminum Insert Panels by fixing Top and Bottom Aluminum Insert Adaptors to .090” aluminum sheet * Extruded aluminum * 16’1” extruded lengths * Clear anodized to facilitate the sliding

motion

* For illuminated applications:

Routed out graphics backed with plastic

* For non-illuminated applications:

Painted or applied vinyl graphics

Create custom height Plastic Insert Panels by fixing Top and Bottom Plastic Insert Adaptors to .125” plastic sheet * Extruded modified DR white acrylic * 8’1” extruded lengths * For illuminated applications:

Surface painted opaque background over applied masking films (applied masking films are removed to reveal translucent graphics) * For non-illuminated applications: Painted or applied vinyl graphics

4” Extruded Panels

6” Extruded Panels

8” Extruded Panels

Custom Height Aluminum Panels

Custom Height Plastic Panels

EXTRUSIONS

A simple new approach to flush changeable message panels

EXTRUSIONS

SignComp products offer variety for design applications Series 12 Hinge Body

Part #1612 For low profile, hingeable applications

Adjustable Reveal

6” Radius ¼ Round End

Plan View

Available with or without 6” Radius Ends

2SIGNCOMP1671

Elevation

View

Series 7 Hinge Body 24’2”

2SIGNCOMP1592 For post & panel, hingeable applications

Adjustable Reveal

3 Post Selections

Plan View

Plan View

Elevation

View

Elevation

View

Elevation

View

Series 7 Single Face Hinge Body

Part #1602 For wall mounted, hingeable applications

6” Radius 1/4 Round End 2SIGNCOMP1671

Plan View

Adjustable Reveal

Available with or without 6” Radius Ends

Series 3 Access Body

Part #1290 For non-illuminated,

post & panel applications

Adjustable Reveal

Plan View

8 Post Selections

Series 7/12 Retro Body

Part #1600 For retro fit or custom depth applications

Plan View

Custom depth, hingeable, single or double face applications are achieved by attaching the Series 7/12 Retro Body to fabricated or existing sign cabinet frames.

Insert Panels slide in and slide out after Insert End Cover is removed

Hingeable aluminum framework

Simply remove Insert End Cover to access insert panels Insert Panels are supported the full width by concealed Insert Dividers

End view of Insert Divider

Flush, countersunk stainless steel fasteners hold the Insert End Cover in place Concealed, structural dividers support the Insert Panels Aluminum Insert Panels, Insert Divider and Aluminum Insert Panel Adaptors are supplied clear anodized to facilitate the sliding motion Integrated, hingeable frame allows for easy access for service

EXTRUSIONS

The simplicity of SignComp’s changeable Insert Panels on hingeable aluminum frames

EXTRUSIONS

Available in Series 3, 7 and 12

Series 12 Hinge Body

Series 7 Hinge Body

Part #1612

Series 7 Single Face Hinge Body

Part #1592

Double face, ground mounted, hingeable applications

Double face, post & panel, hingeable applications

Part #1602

Single face, wall mounted, hingeable applications

2-5/16

Series 7/12 Retro Body Part #1600

The Insert Panel System easily integrates with: 12 Hinge Body 7 Hinge Body 7 Single Face 3 Access Body 7/12 Retro Body

Choice of two End Covers Insert End Cover

Extended Insert End Cover

Part #1696 1/8”

1-1/4”

Part #1698

1-1/4”

3/16”

Corner Key

Part #5210

1-1/4”

1-3/16”

Corner Key Part #5210

Insert Divider Tab shelf Extruded Insert Panel

Part #1290 Double Face, post & panel, non-hingeable applications

Custom depth, hingeable, single or double face applications are achieved by attaching the Series 7/12 Retro Body to fabricated or existing sign cabinet frames.

Double face or single face, post & panel or ground mounted, hingeable applications

Series Series Series Series Series

Series 3 Access Body

Access Frame Part #1690

Access Frame Part #1690

Series 3 square ⅜ cap 2SIGNCOMP 5406

Divider corner angle 2SIGNCOMP5300

Custom cutting available Hinge Screw 2SIGNCOMP5170

2T-12-14-75 Teck 12-14x3/4in.

Reg Post Cap ⅜ S7 2SIGNCOMP5034

Frame corner angle 2SIGNCOMP 5305

Use Teck #10 x ⅝ 2SIGNCOMP5218

Closure Screw 2SIGNCOMP5180

Cap Screw 2SIGNCOMP5040

EXTRUSIONS

Corner Key 2SIGNCOMP5210

EC-8R

EXCELLART EXTRUSIONS

1 3/32” 8”

1”

1” EC-4,7&8

ITEM- NUMBER 2EC-8R

EC-4,7,8-P

DESCRIPTION

Narrowline Retainer

EC 8R FRAME 26’ MILL FINISH

EC-8R Frame System

ITEM- NUMBER

The EC-8R frame system is 8" in depth and is designed for double face cabinets. EC-8R system was designed for lightweight interior and exterior applications. Unique to the EC-8 system is its 1" radius retainer. This system will hold up to 3/16" material in its built-in retainer system. The removable retainer integrally locks into the EC-8 frame to close the face in on both sides. When closed, it will lock itself into the EC-8 frame showing no exterior fasteners. Corner angles have also been raised off the bottom of the frame to avoid any visible fasteners around the cabinet. Available in mill finish.

2EC4/7/8-NARROWLINE

EC 4,7,8 RETAINER 20’ 6IN. MILL

2EC4/7/8-P

EC 4,7,8 RETAINER 20’ 6”. BRONZE

EC-4,N

3 7/16” 1 1/16” ITEM- NUMBER

EC-8

DESCRIPTION

DESCRIPTION

2EC4N

EC 4N NARROW LINE 26’ MILL FIN

2EC7-P

EC 7 FRAME 20’ 6” BRONZE

2EC7R-P

EC 7R FRAME 20’ 6” BRONZE

7⅛” 1”

EC-4,RN

EC-8 Frame System The EC-8 Frame system is designed for double face applications. Like the EC-4 & 7 frame systems they all use the "snap" retainer system. This frame system can be used for enter and exit signs or directory signs.

ITEM- NUMBER 2EC-8

DESCRIPTION EC 8 FRAME 26’ MILL FINISH

3 7/8” 1” ITEM- NUMBER 2EC4RN

DESCRIPTION EC 4RN NARROW LINE 26’ MILL FIN

EC-6

1½” 1⅜”

ITEM- NUMBER 2EC-6

6½” ITEM- NUMBER

5⅝”

2EC-6R

DESCRIPTION

EC 6 FRAME 26’ MILL FINISH

DESCRIPTION EC 6R FRAME 26’ MILL FINISH

EXCELLART EXTRUSIONS

EC-6R

EC-6R Frame System

EC-6 Frame System This is a versatile family of sign frame extrusions suitable for most single face applications and some double face situations when using pan formed faces. When constructing a simple, economical, single face sign, the EC-6R frame is an ideal choice since its one-piece design dramatically reduces fabrication time. Of course you will still have a removable retainer on one end to facilitate sliding the face out of the way for service access to the interior of the cabinet. For those times when you require a slightly deeper cabinet, just select the desired EC retainer, including our Flex System, and attach to the EC-6 frame body. With this construction, depths of up to 9" can be obtained. Available in both mill finish and pre-painted dark bronze.

The EC-6 frame system is one of many versatile sign frame extrusions suitable for most single face applications and some double face situations when using pan formed faces. When constructing a simple, economical single face sign the EC-6R frame is an ideal choice based on its one-piece design dramatically reduces fabrication time. This system will have removable retainers on one end to facilitate sliding the face out of the way for service access to the interior of the cabinet. For those times when you require a slightly deeper cabinet just select the desired EC retainer system. With the EC-6 frame many depths can be obtained based on the retainer desired. The EC-6 Frame System is available in both mill and pre-painted dark bronze finishes.

EC-12P

EC-12 Standard Frame System 12” 1⅝”

ITEM- NUMBER 2EC12-P

DESCRIPTION

EC12 STANDARD 20’6” BRONZE.

The widest frame in the EC family, the EC-12 frame can be used for monument signs, pole signs with larger diameter poles or whenever a deeper cabinet is desired. This frame has a design similar to the popular EC-6 and EC-9 frames and boasts a strong 8" corner angle. When using the EC-12 as the main frame body and your choice of any retainer in the EC line you can achieve depths from 12 3/4" with the LF retainer to 20" with the EC Flex System.

The EC-12 frame is available in both mill and pre-painted dark bronze finishes.

EXCELLART EXTRUSIONS

EC-12

7 13/16” 7 3/16”

12”

7”

1⅝”

ITEM- NUMBER 2EC12-HINGED-P

DESCRIPTION

Ec 12 Hinged Frame 20’6” Bron.

7¼”

EC-12 Hinged Frame System Our widest double face frame extrusion for use when hinged access to the light fixtures is desired, monument signs, pole signs with large diameter poles or whenever a deeper cabinet is required. The integral hinge combines a clean appearance with a functional drainage channel. Another design feature is the ability to add a second retainer to the frame. This retainer holds the inside face in place for your readerboard while using the integral retainer system as your vandal cover. When assembled, a reveal is only shown on top of the cabinet, the side and bottom retainers close neatly into place creating a flush cabinet. Cabinet depths from 13 1/4" to 19 ¾" can be achieved depending on the retainer selected. The EC-12 frame is available in both mill finish and pre-painted dark bronze finishes.

ITEM- NUMBER

DESCRIPTION

2EC-CHANLETTRACEWAY

Ec Chan. Lett. Raceway Set

EC-Channel Letter Raceway Consists of: EC-CLR Back - Part #14010-01 EC-CLR Front - Part #14010-02 EC-CLR Lid - Part #14010-03 This is a three (3)-component raceway that will accommodate all the GFI transformers being manufactured to meet UL 2161 requirements. Back and Front extrusions "snap" together to form a 7 1/4" x 7 13/16" raceway. The Front panel can be drilled or routed prior to assembly. A hinged lid is used for easy access. Available in 20'0" stock lengths or cut to size. End caps, braces and baffles are also available.

1⅛” 1 7/16” 1½” 1½” 5/16” 5/16”

ITEM- NUMBER

2F/HINGEDRETAINER-P

DESCRIPTION F Hinged Retainer 20’6” Bronz

ITEM- NUMBER 2F/STANDARD

DESCRIPTION F Standard Retainer 26’ Mill

1½”

ITEM- NUMBER

DESCRIPTION

2EC-LF/RETAINER

Ec Lf Retainer 20’6” Mill Fin.

2EC/LF-RETAINER/1X5

Eclf Retainer 1”x ⅝ X 12’

ITEM- NUMBER

1½”

1¼”

ITEM- NUMBER

2EC-IDS/24X73

DESCRIPTION 24x73 Ids System W/retainer

Standard Frame With Bleed Cover

DESCRIPTION

2RROD2076012

Rond Rod ½” X 12’

2PS4037537510

Pipe Sch 40 ⅜8” Nps 20’.

2PS40387537512

Pipe Sch 40 ⅜” Nps 12’

2CSS-13-1-20

Css-13-1 X 20’ Mill Finished

2CSS-14-1-20

Css-14-1 X 20’ Mill Finished

2CSS-15-26-1”

Css-15 X 26’1” 6063 T-5 Alumi.

2CSS-16-26’1”

Css-16 X 26’1” 6063 T-5 Alumi.

2CSS-12-3-20

Css-12-3 X 20’ B-lite Gold

2CSS-11-1-20

Css-11-1 X 20’ Mill Finished

2CSS-11-3-20

Css-11-3 X 20’ B-lite Gold

2CSS-11-4-20

Css-11-4 X 20’ B-lite Chrome

2CSS-10-3-20

Css-10-3 X 20’ B-lite Gold

Teak

EC-Flex Clip

Signcom P 5040

Signcomp 5170

Signcom PS 180

EXCELLART EXTRUSIONS

1¼”