Luting Compass
A step-by-step guide for permanent, indirect restorations.
Overview of step-by-step guides Choose your procedure
FIND YOUR INSTRUCTION-PAGE WITH THE COMPASS-MAP BELOW
1st CHOICE WHAT RESTORATION TYPE ARE YOU PERFORMING?
2nd CHOICE WHAT RESTORATION MATERIAL ARE YOU USING?
3rd CHOICE WHAT PREPARATION ARE YOU LUTING ON?
4th CHOICE WHAT LUTING MATERIAL DO YOU PREFER TO USE?
These guidelines are simplified graphical step-by-step instructions. Please refer to the official instructions for use for further details.
Steps/times may vary, depending on materials used.
Light-curing luting materials (see option 6-9) may only be used if sufficient light exposure through the restoration can be guaranteed.
1 4 7 9 8 5 6 2 3
Dentine/EnamelComposite Zirconia / Metal Silicate Ceramic ABABABAB Inlay/ Onlay/ Overlay Composite 16 Silicate Ceramic 27 Zirconia 26 Metal (e.g. Gold) 2 Veneer Composite 6 Silicate Ceramic 7 Zirconia 6 Crown / Bridge Composite 16163638 Silicate Ceramic 27274749 Zirconia 26264648 Metal (e.g. Gold, PFM, CoCr) 2 2 4 4 Post Metal (e.g. Titanium) 5 Glass Fiber 5 Zirconia 5 A Dual-curing Resin Cement B Light-curing Composite 1234
1st Step Pretreatment Restoration
Composite: Sandblast
2nd Step Pretreatment Preparation
Tooth enamel: Phosphoric etch (selective etch)*
Roughen with rotary instrument
3rd Step Luting
1
Composite:
Material Selection Luting SoloCem Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation ONE COAT 7 UNIVERSAL* Material Selection Etching Etchant Gel S*
COLTENE Diamond Instruments with fine grit (red color ring) Sandblast Clean Dry Etch 15s Roughen Bond 20s Cure 10s ≥800 mW/cm2 * Cure 30s each ≥800 mW/cm2 Cure 3s or wait Remove excess Rinse 20s Rinse Blow 5s Discard Dry Dry Bond 20s* Lute Blow 5s Place Optional: If improved bond strength is required due to low retentive preparation Overview
Roughening
1st Step Pretreatment Restoration
Zirconia/Metal: Sandblast
Sandblast
2nd Step Pretreatment Preparation
Roughening
Tooth enamel: Phosphoric etch (selective etch)
Composite: Roughen with rotary instrument
3rd
Luting
2
Step
Material Selection Luting SoloCem Priming Restoration –Priming Preparation ONE COAT 7 UNIVERSAL*
Selection
Etchant Gel S*
Material
Etching
COLTENE Diamond Instruments with fine grit (red color ring)
Clean Etch Rinse Dry Dry
Silicate
Etch 15s Roughen Rinse Rinse Dry Dry Bond 20s Lute Place Cure 3s or waitRemove excess Blow 5s* Discard Cure 10s ≥800 mW/cm2 * Cure 20s each or wait ≥800 mW/cm2 Optional: If improved bond strength is required due to low retentive preparation Overview
Ceramic: Hydrofluoric etch
1st Step Pretreatment Restoration
Composite: Sandblast
2nd Step Pretreatment Preparation
Zirconia/Metal: Sandblast
Silicate Ceramic: Hydrofluoric etch
3rd Step Luting
3
Material Selection Luting SoloCem Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation –Sandblast Sandblast Etch Bond 20s Place Cure 3s or waitRemove excess Blow 5s Discard Lute Rinse Clean Clean Dry Dry Dry Cure 30s each ≥800 mW/cm2 Overview
1st Step Pretreatment Restoration
Zirconia/Metal: Sandblast
2nd Step Pretreatment Preparation
Zirconia/Metal: Sandblast
Ceramic: Hydrofluoric etch
Silicate Ceramic: Hydrofluoric etch
3rd Step Luting
4
Material Selection Luting SoloCem Priming Restoration –Priming Preparation –
Silicate
Sandblast Sandblast Clean Dry Clean Etch Rinse Dry Dry Etch Rinse Dry Discard Remove excess Lute Place Cure 3s or wait Cure 20s each or wait ≥800 mW/cm2 Overview
5 1: 00 min ParaCore SLOW 1:00 min ParaCore 0:30 min 1st Step Pretreatment Post 2nd Step Pretreatment Root Canal
Step, Option 2 Luting Material Selection Luting SoloCem Priming Post –Priming Root Canal –3rd Step, Option 1 Luting Material Selection Luting ParaCore Priming Post –Priming Root Canal ParaBond Dispense Clean/Dry According to manufacturer’s specifications Blow 2s Blow 2s Place Lute Lute Discard Condition 30s Remove excess Remove excess Cure 30s or wait ≥800 mW/cm2 Bond 30s M ix 1:1 Discard LuteLute Place Cure 30s or wait ≥800 mW/cm2 Overview
3rd
1st Step Pretreatment Restoration
Composite/Zirconia: Sandblast
2nd Step Pretreatment Preparation
Material Selection
Etching Etchant Gel S
Roughening COLTENE Diamond Instruments with fine grit (red color ring)
Tooth enamel: Phosphoric etch (selective etch)
15s
Composite: Roughen with rotary instrument
Zirconia/Metal: Sandblast Material
3rd Step Luting
6
Luting BRILLIANT EverGlow/BRILLIANT EverGlow Flow Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation ONE COAT 7 UNIVERSAL
Selection
Clean Dry Etch
Roughen Sandblast Bond 20s Blow 5s Lute Place Bond 20s Blow 5s Clean Dry Rinse Dry Rinse 20s Dry Cure 10s ≥800 mW/cm2 Cure 40s each ≥800 mW/cm2 Remove excess Overview
Sandblast
1st Step Pretreatment Restoration
Silicate Ceramic: Hydrofluoric etch
Etch
2nd Step Pretreatment Preparation
Material Selection
Etching Etchant Gel S
Roughening COLTENE Diamond Instruments with fine grit (red color ring)
Tooth enamel: Phosphoric etch (selective etch)
Etch 15s
Composite: Roughen with rotary instrument
Zirconia/Metal: Sandblast Material
3rd Step Luting
7
Luting BRILLIANT EverGlow/BRILLIANT EverGlow Flow Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation ONE COAT 7 UNIVERSAL
Selection
Roughen Sandblast Bond 20s Blow 5s Lute Place Bond 20s Blow 5s Clean Dry Rinse Dry Rinse 20s Dry Rinse Dry Cure 10s ≥800 mW/cm2 Cure 40s each ≥800 mW/cm2 Remove excess Overview
1st Step Pretreatment Restoration
Composite/Zirconia: Sandblast
2nd Step Pretreatment Preparation
Silicate Ceramic: Hydrofluoric etch
3rd Step Luting
8
Material
Luting BRILLIANT EverGlow/BRILLIANT EverGlow Flow Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation ONE COAT 7 UNIVERSAL Sandblast Clean Etch Bond 20s Bond 20s Blow 5s Bond 5s Lute Place Rinse Dry Dry Cure 10s ≥800 mW/cm2 Cure 40s ≥800 mW/cm2 Remove excess Overview
Selection
1st Step Pretreatment Restoration
Silicate Ceramic: Hydrofluoric etch
2nd Step Pretreatment Preparation
Silicate Ceramic: Hydrofluoric etch
3rd Step Luting
9
Material Selection Luting BRILLIANT EverGlow/BRILLIANT EverGlow Flow Priming Restoration ONE COAT 7 UNIVERSAL Priming Preparation ONE COAT 7 UNIVERSAL Rinse Dry Dry Rinse Etch Etch Bond 20s Place Remove excess Bond 20s Blow 5s Lute Cure 10s ≥800 mW/cm2 Cure 40s each ≥800 mW/cm2 Blow 5s Overview
© COLT E NE – www.coltene.com
Coltène/Whaledent AG Feldwiesenstrasse 20 9450 Altstätten / Switzerland
Center
DE Coltène/Whaledent GmbH + Co. KG
30 DE-89129 Langenau 80000331 08.22
CH
Service
service@coltene.com
Raiffeisenstraße