PURELAB
Analytical Research
PURELAB Prima 7/15/30
The PURELAB Prima is ideal for feeding ultra-pure water systems and for a wide range of laboratory applications including glassware washing, autoclave feed and for use in environmental cabinets.
• Simple to use and maintain with a clear display of water quality • Auto rinse facility maintains purity of water after periods of low use • Minimal consumables delivers a lower cost of ownership • Provides for future changes in demand with easy upgradeability to
The costeffective choice for glassware washing
higher flow rates
• Optional integral feedwater boost pump reduces costs
Process Flow PURELAB Prima 7/15/30
Process Flow PURELAB Prima 7/15/30 Water Quality Sensor Outlet
PreTreatment
Feedwater Inlet
Boost Pump (optional)
Reverse Osmosis
Outlet
Outlet Reverse Osmosis
Reverse Osmosis
Sanitization Port
Drain
Outlet to Docking Vessel or Reservoir
PURELAB
Analytical Research
Treated Water Specifications Model
Make up rate1 Daily output (nominal max) 1 Output reverse pressure (max) Purity: Inorganic - minimum
Inorganic - typical Organics (MW>100 Dalton) TOC2 Bacteria2 Particles 1
Prima 7
7.5 l/hr 180 l/24 hour day 0.1 bar (1 psi) >90% rejection
up to 98% rejection >99% rejection <50 ppb <5 CFU/ml >99% rejection
Prima 15
15 l/hr 360 l/24 hour day 0.1 bar (1 psi) >90% rejection
up to 98% rejection >99% rejection <50 ppb <5 CFU/ml >99% rejection
Prima 30
30 l/hr 720 l/24 hour day 0.1 bar (1 psi) >90% rejection
up to 98% rejection >99% rejection <50 ppb <5 CFU/ml >99% rejection
Standard conditions are 4 bar inlet pressure, <0.1 bar back pressure at 15 degrees centigrade, fed with potable water and a clean pre-treatment
cartridge. Refer to flow tables outside these conditions. 2Subject to correct operating and maintenance procedures.
Dimensions and weights Height Width Depth Weight with internal boost pump Weight without internal boost pump
Feedwater Requirements
Source quality Fouling index - maximum Conductivity Free chlorine - maximum Heavy metals - maximum Silica - maximum Temperature Flowrate (maximum requirement) Drain requirements (gravity fall with air gap). Maximum during service Feedwater Pressure Maximum - without internal boost pump Minimum - without internal boost pump Maximum - with internal boost pump Minimum - with internal boost pump
460mm (18.1in) 410mm (16.2in) 270mm (10.6in) 13.5kg (30lb) 11.5kg (25lb)
460mm (18.1in) 410mm (16.2in) 270mm (10.6in) 14.5kg (32lb) 12.5kg (28lb)
460mm (18.1in) 410mm (16.2in) 270mm (10.6in) 15.0kg (33lb) 13.0kg (29lb)
Potable mains water supply 10 <1400µS/cm 0.5 ppm 0.05 ppm 30 ppm 1 - 35°C 145 l/hr 70 l/hr
Potable mains water supply 10 <1400µS/cm 0.5 ppm 0.05 ppm 30 ppm 1 - 35°C 150 l/hr 70 l/hr
Potable mains water supply 10 <1400µS/cm 0.5 ppm 0.05 ppm 30 ppm 1 - 35°C 155 l/hr 80 l/hr
6.0 bar (90 psi) 4.0 bar (60 psi) 2.0 bar (30 psi) Flooded Suction
6.0 bar (90 psi) 4.0 bar (60 psi) 2.0 bar (30 psi) Flooded Suction
6.0 bar (90 psi) 4.0 bar (60 psi) 2.0 bar (30 psi) Flooded Suction
100-240V ac, 50-60Hz all models 24V dc 52VA 28VA
100-240V ac, 50-60Hz all models 24V dc 52VA 28VA
100-240V ac, 50-60Hz all models 24V dc 52VA 28VA
2 x T3.15 Amp Jack Plug 3.5mm <45dBA
2 x T3.15 Amp Jack Plug 3.5mm <45dBA
2 x T3.15 Amp Jack Plug 3.5mm <45dBA
Electrical Requirements Mains input System voltage Power consumption with boost pump Power consumption without boost pump Fuses Reservoir level connection Noise level
ELGA LabWater Tel: +44 (0) 1494 887500 Fax: +44 (0) 1494 887505 Email: info@elgalabwater.com Website: www.elgalabwater.com ELGA is the global laboratory water brand name of Veolia Water Solutions and Technologies. The information contained in this document is the property of VWS (UK) Ltd, trading as ELGA LabWater, and is supplied without liability for errors or omissions. © VWS (UK) Ltd. 2010 – All rights reserved. ELGA® and PURELAB® are registered trademarks of VWS (UK) Ltd.
LITR 38751-04