Environmental Science & Engineering Magazine September-October 2013

Page 1

September/October 2013

www.esemag.com


DULCOMETER®

diaLog

DACa

multi–parameter controller Experts in Chemical Feed and Water Treatment

The new diaLog DACa controller from ProMinent was developed for continuous measurement and control of required parameters and can be configured for one or two* measuring channels.

Two independent measurements (each with mV or mA inputs) and PID control in one device

Free choice and combination of 14 selectable measured variables

Two 2-way PID controllers with 4 metering pump outputs

Sensor monitoring for pH (glass breakage and short circuit)

Data logger for measured values, control variables, digital inputs, calibration data and events with storage on SD card and numerical depiction on the display

Control parameter switching using timer and externally controlled event

External setpoint adjustment via mA signal

Temperature compensated pH compensation for chlorine measurement

uring intelligent meas and controlling

+ data-logging! *depending on the application

Available from

Industrial Pump Systems

ProMinent Canada Toll Free: eMail: www.

1-888-709-9933 sales@prominent.ca prominent.ca

SANSOM EQUIPMENT LIMITED

ProMinent USA Phone: eMail: www.

(412) 787-2484 sales@prominent.us prominent.us


ÂŽ

WE SEE THE FUTURE IN EVERY DROP OF WATER SAVED.

DO YOU?

Master Meter is leading the development of smart water management solutions. We believe that our decisions today will ultimately affect the world we live in tomorrow — and it all begins with us.

Get the story at www.mastermeter.com/preserve


Contents ISSN-0835-605X • Sept/Oct 2013 Vol. 26 No. 5 • Issued October 2013 Editor and Publisher STEVE DAVEY E-mail: steve@esemag.com Founding Editor

TOM DAVEY

Sales Director PENNY DAVEY E-mail: penny@esemag.com Sales Representative DENISE SIMPSON E-mail: denise@esemag.com Accounting SANDRA DAVEY E-mail: sandra@esemag.com Circulation Manager DARLANN PASSFIELD E-mail: darlann@esemag.com Design and Production EINAR RICE Editorial Assistant PETER DAVEY E-mail: peter@esemag.com

Technical Advisory Board Archis Ambulkar Brinjac Engineering, Pennsylvania

FEATURES 6

DEPARTMENTS

Horrors of the past obscured by romantic images of rustic living

10 Society has benefited from 120 years of environmental journalism ES&E’s 25th anniversary special

Product Showcase . . . 71-75 Environmental News . 76-80 Professional Cards . . . 76-80 Ad Index . . . . . . . . . . . . . . 82

26 5S Society has recognized key contributors to the wastewater profession for over 70 years 28 Recent no-fault orders passing spill clean-up costs onto innocent parties 30 Managing distribution system water loss with pressure reducing valves 32 Modified SBR system offers effluent reuse potential

Jim Bishop Consulting Chemist, Ontario

36 Controlling Geosmin and MIB in water reservoirs and treatment plants

Peter Laughton P.Eng. Consulting Engineer, Ontario

40 Installing an innovative deep-trench drip disposal system

Bill DeAngelis, P.Eng. Associated Engineering, Ontario Marie Meunier John Meunier Inc., Québec Peter J. Paine Environment Canada

Environmental Science & Engineering is a bi-monthly business publication of Environmental Science & Engineering Publications Inc. An all Canadian publication, ES&E provides authoritative editorial coverage of Canada’s municipal and industrial environmental control systems and drinking water treatment and distribution. Readers include consulting engineers, industrial plant managers and engineers, key municipal, provincial and federal environmental officials, water and wastewater plant operators and contractors. Information contained in ES&E has been compiled from sources believed to be correct. ES&E cannot be responsible for the accuracy of articles or other editorial matter. Articles in this magazine are intended to provide information rather than give legal or other professional advice. Articles being submitted for review should be e-mailed to steve@esemag.com. Canadian Publications Mail Sales Second Class Mail Product Agreement No. 40065446 Registration No. 7750 Undeliverable copies, advertising space orders, copy, artwork, proofs, etc., should be sent to: Environmental Science & Engineering, 220 Industrial Pkwy. S., Unit 30, Aurora, Ontario, Canada, L4G 3V6, Tel: (905)727-4666, Fax: (905) 841-7271, Web site: www.esemag.com

46 Effective WWTP odour control systems provide many benefits 49 Improving nitrification at Caledonia’s wastewater treatment plant 52 Evaluating the impact of hexavalent chromium on drinking water 54 Quebec lakefront lodge gets new high-performance wastewater treatment system 56 Rain gauge network vital to cities when a major storm hits 60 Tuning the accuracy of WW lift station flow rates 62 Geotubes successfully used for storm water pond sediment dewatering 64 London recognized for its new biosolids ash management system 66 Four ways your DO measurements are being affected 69 Immediate pH correction for fluctuating flows offers many benefits 81 Innovative siphon hydraulics at Nanaimo’s new WTP cuts capital and operating costs Page 10

Page 30

Page 49



Comment by Tom Davey

Horror stories of past obscured by romantic images of rustic living

S

cience, chemistry, and engineering were the cutting edges of the Industrial Revolution which was undeniably brutal. Child labour, worker exploitation, dangerous working conditions, all were part of this revolution which reshaped our world forever. Charles Dickens brilliantly captured WKH XUEDQ VTXDORU LQ KLV ÂżFWLRQ \HDUV ago. More recently, social scientist PeWHU ) 'UXFNHU LQ KLV HVVD\ “The Age of Social Transformation,â€? wrote that, while industrial workers were LQGHHG SDLG SRRUO\ DW ÂżUVW WKH\ ZHUH still paid better than farm or household workers. Moreover factory workers ZRUNHG VSHFLÂżHG KRXUV XQOLNH VHUYDQWV and farmers who were often kept working at the whim of employers. Drucker notes that infant mortality rates dropped immediately when farmers and domestic servants moved into factory work. It should be added that technology led directly to the emancipation of women, as knowledge and intellectual skills increasingly displaced brutal muscle power in the industrial marketplace. Ultimately, the development of a skilled working class, along with the wealth generated by mass production, freed a long-abused rural class from centuries of misery and deprivation. The development of canals, roads, ships, railways and planes increasingly slashed the costs of food, goods and services in economies previously serviced by pack horses and camels. To the economies of scale were added the economies of scope, as advances in transportation technology rivaled that of manufacturing. A pack horse, carrying cotton goods to Liverpool, FRXOG RQO\ KDXO DERXW NLORJUDPV DV LW wound along Lancashire’s hilly terrain. The same horse pulling a canal barge could move several tonnes directly into the great port. Indeed, it was a canal that converted Manchester, an inland city, into a port with a global reach. The barges later carried food from around the world to feed the factory

6 | September/October 2013

workers, completing a cycle in the revolution that was to encircle the world. Fifty per cent of Britain’s economic growth since the Industrial Revolution was due to better nutrition, according to economist and Nobel laureate Robert Fogel. But nutrition alone does not always lead to better health. Increasingly, the

crowded slums around the factories led to lethal outbreaks of disease until the development of sanitary engineering drastically improved public health. Those diseases, which tragically are still endemic in many developing countries, are now found only in the history books of modern societies, a direct benHÂżW RI WKH ,QGXVWULDO 5HYROXWLRQ %XW SHUKDSV WKH ELJJHVW EHQHÂżW LV WKH one most overlooked: that democracy usually displaces despotism when citizen empowerment replaces feudal systems. The dynamic that gave the workers manufacturing skills, also gave them political power. Drucker notes pointedly that the three great destroyers of our age, Hitler, Stalin and Mao, produced absolutely nothing in their lifetimes, except wreckage. The works of the remarkable French-

man, Fernand Braudel, should be required reading. Conventional history tells us much about pharaohs, caesars, kings and queens, but surprisingly little about the lives of average people. ,Q *HRUJH 3XWWHQKDP D PDMRU ÂżJXUH LQ (OL]DEHWKDQ (QJOLVK OLWHUature, wrote: “The good and the bad of princes is more exemplary and thereby of greater moment than private persons.â€? And so it was that most histories were focused, with working people being virtually ignored. But in his books such as Structures of Everyday Life, the )UHQFK KLVWRULDQ UHFWLÂżHG WKLV KLVWRULFDO vacuum by showing how ordinary people lived and worked over the ages. Braudel weaves an intricate tapestry from historical facts, which dispels many of the romantic illusions that some youthful environmentalists have of pre-industrial society. He ignores the more regal focus of his contemporaries and deals with such fundamentals as births, marriages, and life expectancies of earlier societies. Also examined are energy sources and uses, economics, social change, and urbanization – all areas commonly neglected by orthodox historians. Many ecologists emotionally link acid rain with Blake’s Satanic Mills and now regard all industry and technology ZLWK GHHS VXVSLFLRQ %UDXGHOÂśV ÂżQGLQJV would undoubtedly shock some of our environmental zealots with their suspicions of, and deep seated resistance to, science and technology. In pre-industrial societies, millions labored in appalling conditions so that a few might OLYH LQ OX[XU\ (YHQ DW WKH WXUQ RI WKH th century it was said that Britain was KHDYHQ IRU SHRSOH ZKLOH EHLQJ D KHOO IRU PLOOLRQ Braudel’s research, however, reveals that even the rich lived in conditions that would disgust modern Canadians. Conventional French historians tell us of the wonders of the great chateaux, the glory of Versailles, its splendid architecture, glistening mirrors, and elegant intericontinued overleaf...

Environmental Science & Engineering Magazine


ONE O NE C COMPANY. OMPANY S STRONG TRONG B BRAN RAND DS. S

Biological Treatment | Filtration & ClariďŹ cation UV Disinfection & Ozone Oxidation | Mixing Applications Xylem offers a full spectrum of water and wastewater treatment solutions.

xylemwatersolutions.com/ca 1.800.588.7867 (PUMP)


Comment by Tom Davey ors. But when I visited Versailles not long ago, I learned that food was served cold because the kitchens were located far away from the main palace. In fact, WKH RULJLQDO PDUEOH ÀRRUV ZKLFK NHSW the palace so cold that wine was known to freeze in winter, were torn up to be replaced with wood. If the stench of the nobility’s houses centuries ago would nauseate us today, the hovels of the poor, by far the overwhelming majority, must have been unbearable. As Braudel so eloquently puts it, the world, prior to industrial development, was a brutal, disease-ridden and hungry place for its inhabitants, most of whom had very short life expectancies. The most comfortable inhabitants of WKRVH WLPHV ZHUH WKH ÀHDV OLFH UDWV DQG other vermin which infested the houses of rich and poor alike. Braudel stresses that every human being born before the 20th century was actually lucky to have lived. Most babies simply did not survive and those hardy ones who did, for the most part, had short lives punctuated by crippling diseases. Without contemporary sci-

ence, there were no drugs to ease the pain, or machines to diagnose many medical conditions that can easily be treated today. Ironically, the 16th century Flemish artist Pieter Bruegel painted wonderful ODQGVFDSHV ¿OOHG ZLWK EXFROLF SHDVDQWV frolicking happily in their rustic environments. While Bruegel’s name is similar to the historian’s, his paintings seem like artistic satires, at odds with WKH PLVHU\ UHYHDOHG E\ %UDXGHOœV ¿QGings. Most of our history was burdened by regular famine. Now we have lucrative fat farms, health clubs and companies such as Weight-watchers, whose clients pay money to work out and eat less. Actually paying money to diet and WRLO LQ J\PV UDWKHU WKDQ WKH ¿HOGV LV D situation unprecedented in human history. But our militant activists seem unaware that many less fortunate countries, lacking our technology, relentlessly continue a protracted and unequal battle with nature. Even more tragic is the fact that most poverty stricken peo-

ple are politically powerless, unable to protest their miserable conditions. The works of Braudel and Drucker should be required reading for today’s professional malcontents, perhaps even becoming mandatory issue when the protest placards are being handed out. If activists knew a little more history, some might become grateful for ¹ LQVWHDG RI KRVWLOH WR ¹ WKH EHQH¿WV RI technology, which have enriched and extended our lives, while creating a climate of political freedom in which to complain about it all.

This editorial was published in Tom Davey’s book “For Whom the Polls Tell�.

Waterra WS Water Level Sensors are advanced products utilizing the most recent electronic technology. Both our Water Level Sensors and Oil/Water Interface Sensors include innovative design features, as well as compactness, portability and reliability — all at an affordable price. • EXTREMELY LOW POWER CONSUMPTION • POLYETHYLENE COATED 3/8" STAINLESS STEEL FLAT TAPE • AVAILABLE IN BOTH METRIC & IMPERIAL GRADUATIONS

• AUTO SHUT-OFF • SENSITIVITY ADJUSTMENT • POWERED BY 4 AA CELLS • MEMBRANE ON/OFF SWITCH • WS-2 CLOSED REEL ALSO AVAILABLE

WATER LEVEL SENSORS www.waterra.com (CANADA) Waterra Pumps Limited sales@waterra.com • tel: 905.238.5242

8 | September/October 2013

(USA) Waterra USA Inc. waterra@openaccess.org • tel: 360.738.3366

Environmental Science & Engineering Magazine



ES&E’s 25th Anniversary Special

Society has benefited from 120 years of environmental journalism By Tom, Steve and Peter Davey

T

he year 2013 is indeed a milestone year. It marks Environmental Science & Engineering Magazine’s (ES&E) 25th birthday and 120 years of environmental journalism in Canada. It also marks the 30th anniversary of a historical research project Steve Davey did to commemorate Water & Pollution Control Magazine’s (W&PC) 90th birthday in 1983. W&PC’s origins began 120 years ago, when it was launched as The Canadian Engineer. W&PC had been a respected publication, which had several name changes over its lifespan after it began as a general magazine serving professional engineers. But, even in its early GD\V WKH SXEOLFDWLRQ ¿UVW D monthly and later as a weekly, had a profound interest in environmental engineering. Some of the early environmental engineering giants were featured in W&PC and it would be of interest to many environmental groups to know that there had been vigorous environmental concerns and remediation had taken place as early as the 1800s.

in the 1850s. Then, in approximately 1853, he was appointed chief engineer of the Montreal Waterworks, with the task of constructing a public water supply for the city. The project was so well executed, that his services were soon at a premium for similar installations elsewhere in the country. For some 25 years he was involved, often in a consulting capacity and sometimes as an employee, on waterworks projects for the cities of Toronto, St. Catharines, Hamilton, Quebec City, Ottawa, London, Halifax and Dartmouth. In 1872, he became chief engineer of the Ottawa Waterworks. Some Keefer projects were mentioned in The Canadian Engineer and he ran a professional card in it. Thomas Keefer was keenly aware of the need for engineering education in Canada. He was instrumental in introducing civil engineering at McGill University in Quebec DQG EHFDPH LWV ¿UVW SURIHVsor of engineering, in 1856, some 11 years before confederation. He was a founding PHPEHU DQG ¿UVW SUHVLGHQW RI the Canadian Society of Civil Engineers. This remarkable man died in 1915, in his 94th year. ApCanada’s water and propriately, a pumping stawastewater pioneers tion he designed in 1859 in The magazine had pubHamilton, Ontario, was deslished news on such engiignated a National Historical neering greats as Samuel Monument on June 11, 1983, and Thomas Keefer and their by the Canadian Society of biographies are well recordCivil Engineering. Keefer’s ed. Worthy of note: Thomas engineering masterpiece is Coltrin Keefer was active in kept in mint condition by The water transportation engineer- Thomas Keefer designed this historic Hamilton pumping Hamilton Museum of Steam & Technology and has been ing in the 1840s and railways station in 1859.

10 | September/October 2013

Environmental Science & Engineering Magazine


ES&E’s 25th Anniversary Special SXEOLFDWLRQ 7KHVH PHQ SOD\HG QRW RQO\ D featured several times in ES&E. tremendous role in the discipline of civW&PC also carried articles on WilLO HQJLQHHULQJ EXW WKH\ DOVR ZHUH YHU\ lis Chipman, the founder of Chipman DFWLYH LQ GHYHORSLQJ SURIHVVLRQDO DVVRand Power, which was almost certainFLDWLRQV :LOOLV &KLSPDQ ZDV D IRXQGLQJ O\ &DQDGDœV ¿UVW VLJQL¿FDQW FRQVXOWmember of the Ontario Association of LQJ HQJLQHHULQJ FRPSDQ\ %\ WKHQ KH Land Surveyors, the Association of Prohad completed both waterworks and IHVVLRQDO (QJLQHHUV RI 2QWDULR $3(2 VHZDJH WUHDWPHQW SURMHFWV LQ FLWLHV DQG WKH (QJLQHHULQJ ,QVWLWXWH RI &DQDGD from Halifax, Nova Scotia to Victoria, 'U %HUU\ WRR DOWKRXJK \RXQJHU WKDQ %ULWLVK &ROXPELD 6RPH RI &KLSPDQœV Willis Chipman, was instrumental in the SXEOLVKHG DUWLFOHV LQ WKH PDJD]LQH FRYformation of APEO. HUHG VXFK WRSLFV DV /RQGRQœV VHZDJH 7R UHYLHZ WKHVH HDUO\ LVVXHV RI WKH system, Oakville Waterworks AuxiliaPDJD]LQH LV WR JHW D QHZ DSSUHFLDWLRQ RI ry and the Ontario waterworks system. the term Civil Engineering, because it is :LOOLV &KLSPDQ HQJLQHHUHG ZDWHU DQG PRVW DSSDUHQW WKDW WKH ZRUNV DQG SURMVHZDJH SURMHFWV DFURVV &DQDGD XQWLO KH The founder of Chipman Power, Willis HFWV RI WKH FLYLO HQJLQHHU KDG LQ WUXWK D GLHG KRZHYHU WKH ¿UP GLG QRW VXUYLYH Chipman. profound civilizing LQÀXHQFH beyond its founders. ,W LV FRPPRQ IRU ZULWHUV WR XVH FDWKHGUDOV DQG RWKHU DU%XW E\ WKHQ RWKHU \RXQJ FRQVXOWLQJ FRPSDQLHV VXFK DV ( $ -DPHV DQG *RUH 1DVPLWK DQG 6WRUULH KDG EHJXQ WR PDNH FKLWHFWXUDOO\ DGYDQFHG EXLOGLQJV DV WKH PDUN RI D JUHDW FLYLOL]DWLRQ +RZHYHU LW ZDV WKH VHZHUV ZDWHUZRUNV DQG ZDVWH their mark in Canadian history. ( $ -DPHV EHJDQ LQ DQG DOWKRXJK LW KDV KDG VHYHUDO treatment schemes of the early pioneers that did much to rid QDPH FKDQJHV RYHU WKH \HDUV LW UHPDLQHG D YLDEOH DQG H[SDQG- FRXQWULHV RI W\SKRLG SDUDW\SKRLG DQG HYHQ FKROHUD 7KHVH LQJ FRPSDQ\ HYHQWXDOO\ EHFRPLQJ RQH RI WKH ODUJHU FRQVXOW- were frequent visitors to Canadian households, with a dramatLQJ HQJLQHHULQJ FRPSDQLHV LQ &DQDGD )RU PDQ\ \HDUV LW ZDV ic effect on infant mortality. ,Q WKH 6HSWHPEHU LVVXH RI WKH PDJD]LQH ( 5 %RXOWHU known as Proctor & Redfern Limited. *RUH 1DVPLWK 6WRUULH EHJDQ D OLWWOH ODWHU DQG LW WRR KDV D VXUYH\RU LV TXRWHG DV VD\LQJ ³the cleansing of house drains VHUYHG LQ DQ XQEURNHQ OLQH SUDFWLFLQJ DV *RUH 6WRUULH /LP- is a matter requiring the serious attention of civil authorities.� +H DGYLVHG WKHP WR YLVLW DOO RFFXSLHG GZHOOLQJV RQ HDFK OLQH RI LWHG EHIRUH EHFRPLQJ SDUW RI &+ 0 +,// LQ WKH ODWH V ,Q WKH HDUOLHU GD\V WKH PDJD]LQH FDUULHG VSHFL¿FDWLRQV DQG the sewer, with all the necessary implements and deodorants GUDZLQJV RI %ULWLVK EDWWOHVKLSV DV ZHOO DV WHFKQLFDO DUWLFOHV RQ WR FOHDQ WKH GUDLQV 7KLV SURFHGXUH ZDV RIIHUHG LQ UHVSRQVH WR WKH FRDO ¿UHG ERLOHUV RI 0RQWUHDOœV ZDWHUZRUNV 7KHUH ZHUH FRPSODLQWV UHJDUGLQJ RGRXUV IURP VHZHU OLQHV 'XULQJ WKH HDUO\ \HDUV IURP WR WKH PDJD]LQH reports of air pollution control devices even then, with adverWLVHPHQWV XUJLQJ UHDGHUV WR EX\ ³the smoke eaters.� Reports JDYH H[WHQVLYH FRYHUDJH WR RSHQLQJV DQG LPSURYHPHQWV RI ZDRI WKH HPHUJLQJ LQWHUHVW LQ R]RQH ZHUH DOVR FDUULHG LQ VRPH RI WHU DQG VHZDJH V\VWHPV $Q LVVXH GHVFULEHV WKH WHFKQLFDO KLJKOLJKWV RI RQH RI WKH :RUWKLQJWRQ SXPSV ZKLFK KDG EHHQ the early issues. ,Q WKRVH GD\V DUWLFOHV RQ :LOOLV &KLSPDQ DQG ODWHU WKH G\- UHFHQWO\ LQVWDOOHG DW WKH 0RQWUHDO :DWHUZRUNV ³The most important feature of modern interest is the high QDPLF \RXQJ 'U $OEHUW (GZDUG %HUU\ ZHUH IHDWXUHG LQ WKH duty attachment which was introduced by the Worthington Company eight years ago and enables the use of steam in a direct acting engine at a high rate RI H[SDQVLRQ ZLWK DQ\ IRUP RI À\ZKHHO engine. The principle is regarded by engineers as being one of the greatest advances in steam practice since the time of Watt ... it has been widely introduced in this continent and in Europe for all kinds of pumping machinery and has shown a savings of from 40 to 50 per cent over the old type of direct acting engine.� 7KH DUWLFOH DOVR GHVFULEHG +HLQH 6DIHW\ %RLOHUV ZKLFK VXSSOLHG VWHDP WR WKH :RUWKLQJWRQ 3XPSV

Professional cards in the early issues of The Canadian Engineer included such notables as T.C. Keefer, top right. www.esemag.com

A manual of civilization ,I WKH ZRUOG VXIIHUHG D FDWDFO\VPLF event which wiped out most of what continued overleaf... September/October 2013 | 11


ES&E’s 25th Anniversary Special QHHUV ZDUQHG WKDW V\VWHPV KDG WR EH GHYHORSHG LQ &DQDGD WR FRSH ZLWK VOXGJH UHPRYDO VLQFH GLOXWLRQ ZDV QR ORQJHU D SUDFWLFDO RU VDIH PHWKRG $QRWKHU DUWLFOH ZDV ZULWWHQ E\ D 7RURQWR :DWHU :RUNV LQVSHFWRU ZKR KDG EHHQ DVVLJQHG WR LQYHVWLJDWH DQ H[FHVVLYH XVH RI ZDWHU +H KDG GLVFRYHUHG DORQJ ZLWK QXPHURXV major and minor leaks, that many peoSOH ZHUH ¿OOLQJ XS SULYDWH SRQGV ZLWK FLW\ ZDWHU DQG VRPH LQGXVWULHV ZHUH ¿OOLQJ XS WKHLU KROGLQJ SRQGV IURP K\drants. ,Q 7RURQWR &LW\ (QJLQHHU 5 + Rust presciently did an article in the PDJD]LQH RQ XVLQJ JDUEDJH IRU SRZHU D WRSLF ZKLFK LV VWLOO D ZLGHO\ GLVFXVVHG VXEMHFW ,Q 'U : 3 0DVRQ RXWOLQHG WKH FDXVHV DQG HIIHFWV RI DFLGLF ZDWHU RQ SOXPELQJ DQG WKH SXEOLF

Montreal Waterworks-Worthington Pump, 1893.

mankind has learned and rebuilt, reFRQVWUXFWLRQ PLJKW EH VLPSOL¿HG LI WKH VXUYLYRUV XQHDUWKHG FRSLHV RI The Canadian Engineer. Since the publication covered many engineering disciplines IRU GHFDGHV DIWHU LW ZDV ODXQFKHG HDUO\ LVVXHV FRQWDLQHG D ZHDOWK RI LQIRUPDtion. ,Q D LVVXH IRU H[DPSOH VWRULHV UDQJLQJ IURP RQH RQ &RXQW =HSSHOLQ¶V HDUO\ DLUVKLSV WR RQH RQ 6LU 6DQIRUG )OHPLQJ WKH &DQDGLDQ ZKR LQYHQWHG WKH FRQFHSW RI LQWHUQDWLRQDO WLPH ]RQHV ZHUH SXEOLVKHG $OZD\V FRQFHUQHG ZLWK VDQLWDWLRQ WKH VDPH LVVXH UDQ DQ DUWLFOH RQ SXULI\LQJ VHZDJH E\ EDFWHULD ,Q LW WKH DXWKRU claimed that it is necessary to “help the EDFWHULD UHPRYH WKH ¿OWK IURP WKH ZDWHU E\ ¿[LQJ WKH SOXPELQJ VR DGHTXDWH DPRXQWV RI DLU DUH GLVFKDUJHG LQWR WKH VHZHUV DORQJ ZLWK WKH VHZDJH DQG E\ FRQVWUXFWLQJ WKH VHZHUV LQ D ZD\ WKDW WKH ÀRZ LV UDSLG DQG WKDW HYHU\ LQFK RI WKH GUDLQ KDV D WKRURXJK XQGXODWLRQ RI DLU WKURXJK LW %\ GRLQJ VR WKH SURFHVV RI EDFWHULDO VHZDJH SXUL¿FDWLRQ FRPPHQFHV LPPHGLDWHO\ DIWHU WKH VHZDJH HQWHUV WKH SLSHV ´ ,W VHHPV WKDW VRPH RI WKH LVVXHV IDFHG E\ VRFLHW\ LQ WKH HDUO\ th centuU\ DUH VWLOO ZLWK XV WRGD\ $ VWRU\ RXWOLQHV RQH SUREOHP HQJLQHHUV ZRXOG KDYH LI WKH PHWULF V\VWHP ZHUH DGRSW12 | September/October 2013

HG 7KH DXWKRU ZURWH WKDW WKDQNV WR WKH ,PSHULDO V\VWHP RI PHDVXUHPHQW LW ZDV HDV\ WR FRPSXWH WKH QXPEHU RI EULFNV D QHZ EXLOGLQJ ZRXOG UHTXLUH VLQFH EULFNV ZHUH WKUHH TXDUWHUV RI D IRRW E\ RQH TXDUWHU RI D IRRW ,I WKH VDPH FDOFXODWLRQ ZDV GRQH LQ PHWULF WKH DXWKRU FODLPHG LW ZRXOG EH IDU WRR FRPSOLFDWHG The same year, an article by R.S. Lea RI WKH &DQDGLDQ 6RFLHW\ RI &LYLO (QJL-

Ads from Canadian Engineer, circa 1899.

Early uses of electricity By 1904, electricity began to displace VWHDP DV WKH PDLQ SRZHU VRXUFH 7KDW VDPH \HDU LW ZDV DQQRXQFHG WKDW WKH *HQHUDO (OHFWULF &RPSDQ\ KDG GHYHORSHG D GLUHFW GULYH HOHFWULF SXPS ZKLFK HOLPLQDWHG WKH QHHG IRU EHOWV DQG JHDUV Additionally, technical details appeared RQ WKH :RUWKLQJWRQ FHQWULIXJDO SXPS ZKLFK ZDV VDLG WR EH PRUH HI¿FLHQW WKDQ SUHYLRXV GHVLJQV DQG ZDV VXLWHG IRU KDQGOLQJ VROLGV FRPPRQ WR VHZDJH WUHDWPHQW SODQWV DQG OLIW VWDWLRQV 'HQLV 3DSLQ LV FUHGLWHG ZLWK GHVLJQLQJ WKH ¿UVW FHQWULIXJDO SXPS DERXW ,Q LW ZDV QRWHG LQ WKH PDJD]LQH WKDW ( $ -DPHV KDG EHHQ DSSRLQWHG UHVLGHQW HQJLQHHU IRU WKH &ROG :DWHU 6HFWLRQ RI WKH 7RURQWR 6XGEXU\ EUDQFK RI WKH &DQDGLDQ 3DFL¿F 5DLOZD\ ,Q ZKHQ KH ZDV WKH WRZQ HQJLQHHU IRU 1RUWK 7RURQWR 0U -DPHV ZURWH DQ DUWLFOH IRU WKH SXEOLFDWLRQ GHVFULELQJ 1RUWK 7RURQWR¶V ZDWHU VXSSO\ DQG K\SRchlorite treatment. 'U *HRUJH * 1DVPLWK 'LUHFWRU RI /DERUDWRULHV IRU WKH +HDOWK 'HSDUWPHQW RI 7RURQWR DQG D IRXQGHU RI DQRWKHU consulting company, Gore & Storrie Limited, contributed an article on the FKHPLFDO SULQFLSOHV LQYROYHG LQ VHZDJH GLVSRVDO +H ZURWH ³,W PD\ QRZ EH DFFHSWHG DV D IDFW WKDW FKHPLFDO DFWLRQ LV WKH EDVLV RI HYHU\ DFWLRQ RI VHZDJH GLVSRVDO 7KDW WKLV LV WUXH WKH VDQLWDU\ HQJLQHHU KDV EHHQ VORZ WR UHFRJQL]H FRQWLQXHG RYHUOHDI

Environmental Science & Engineering Magazine


A Safe Place to Grow

IPEX Protects Your Investment Certain environments demand fail-safe systems. No leaks. No risk. IPEX understands the complexity of design and installation for demanding DOUBLE CONTAINMENT APPLICATIONS. And, unlike other manufacturers, our specialists are part of a division of IPEX dedicated solely to the design, production and installation of state-of-the-art double containment systems. With more than 20 years of experience and success, we are the proven experts. The IPEX family of double containment systems includes: GuardianTM PVC and CPVC, and Clear-GuardTM PVC pressure and drainage systems, EncaseTM PolyPro drainage systems,

CustomGuard® FRP and metal pressure systems and Centra-GuardTM leak detection systems. Safety and environmental concerns are top priorities on today’s industrial agenda. Reduction of emissions, energy conservation and prevention of ground water contamination are some of the areas where regulations are increasingly defining an important line between utilization and exploitation of our planet’s resources. For most common chemical-waste or process applications, IPEX offers systems that are both simple yet highly advanced technologies.

Double Containment Systems We build tough products for tough environments® Products are manufactured by IPEX Inc. GuardianTM, Clear-GuardTM, EncaseTM, CustomGuard®, and Centra-GuardTM are trademarks of IPEX Branding Inc.

Call 1-866-473-9462 or visit www.ipexinc.com


ES&E’s 25th Anniversary Special and he has struggled along for years, endeavouring of empirical experiments to improve existing methods of sewage disposal without having any sound basis for his experiment.â€? The staff of what was The Canadian Engineer had always taken an active role in the industry it served. Over a century ago, editorials by the then editor, Samuel Groves, commented on air pollution regulations: “Municipalities everywhere are beginning to enforce regulations with regards to the smoke nuisance, and rightly so. The evidence is overwhelming that the emissions of black smoke from boiler chimneys can be prevented withRXW ÂżQDQFLDO ORVV ´ Mr. Groves described the Meldrum furnace, which reduced emissions by forcing superheated steam under the airtight ash pits of the boiler. In 1906, he commented on the lack of proper sterilization in the Toronto Water Works System. “Now that Toronto is to have electrical energy at a reasonable price, there is no reason why one of these ozone sterilization plants should not form part of the city’s water works system. It is worthwhile for the Mayor and the corporation to look into this matter,â€? he said. While the magazine reported and presented opinions, it also devoted a lot of space to construction announcements, UHVHDUFK ÂżQGLQJV DQG UHYLHZV In 1905, a practical article appeared on thawing pipes using electricity, while another piece described the Gloucester sewage disposal works. An ongoing feature of each issue was a section entitled “Municipal works, etc.â€? This department gave short announcements of new projects along with the amount of money involved and, in some cases, the engineer who proposed it. In 1905, a $125,000 water works system for Saskatoon was announced in this section, along with a $10,000 water works system for Aurora, Ontario, where ironically ES&E Magazine was launched eight decades later. The magazine also announced in 1906 that Miss Nora Stanton Blatch was elected for membership to the American Society of Civil Engineers. She was in the vanguard of women’s liberation and LV EHOLHYHG WR EH WKH VRFLHW\ÂśV ÂżUVW ZRPan engineer. The headline on that par14 | September/October 2013

iments made at the Manchester Sewage Works in England. Iron salts were added to sewage inoculated with an organism found in old colliery workings and air Water and wastewater was blown through. This produced “a gains prominence Beginning in 1909, the magazine ran limpid sparkling and non-putrafactive a section called the “Sanitary Review,â€? HIĂ€XHQW.â€? In 1914, Messrs. Ardern and Lockett, which dealt with sewage and sewage disSRVDO ZDWHU VXSSO\ DQG SXULÂżFDWLRQ ,Q working in northern England, reported 1912, an article in this section described that a process which they had developed a device developed by Electra Clear “SURGXFHG DQ HQWLUHO\ VDWLVIDFWRU\ HIĂ€X:DWHU &R RI &OHYHODQG ZKLFK SXULÂżHG ent after a few hours’ aeration.â€? This ZDWHU E\ SDVVLQJ LW EHWZHHQ HOHFWULÂżHG became known as the Activated Sludge

ticular announcement read: “Once more masculine stronghold invaded.�

Winnipeg Aquaduct, circa 1918.

DOXPLQXP SODWHV DQG WKHQ ÂżOWHUHG LW through crushed quartz. That year Willis Chipman wrote an article on “Progress in Canada on the Biological Methods of Sewage Disposal during the Last 20 Years.â€? While typhoid epidemics are almost unheard of today in North America, thousands of Canadians died of the disease until sterilization of drinking and wastewater became widespread. In February 1912, the magazine reported on a federal bill before the Senate, which would make it a criminal offence to deposit any wastes from typhoid fever victims into, or near, waterways. In 1913, the magazine began to follow the development of what was to become known as the activated sludge process. That year Professor Gilbert J. Fowler announced the results of exper-

Process and is probably still the most important development in sewage treatment. Ardern and Lockett had a large bottleful of sewage, through which air was EORZQ IRU DERXW ¿YH ZHHNV 7KLV UHVXOWHG LQ WKH FRPSOHWH QLWUL¿FDWLRQ RI WKH VHZage. The supernatant water was decanted and an equal amount of fresh sewage was added and air blown in, resulting in QLWUL¿FDWLRQ LQ PXFK OHVV WLPH 7KH SURcedure was repeated many times, until there was enough activated sludge to inoculate fresh sewage in the proportion of one to four, or one to three. An entirely VDWLVIDFWRU\ HIÀXHQW ZDV REWDLQHG DIWHU D few hours’ aeration. The experiment was then made in casks placed outside and air was distributed through porous tiles. After four continued overleaf...

Environmental Science & Engineering Magazine



ES&E’s 25th Anniversary Special hours of blowing in contact with activatHG VOXGJH SHU FHQW SXULÂżFDWLRQ ZDV effected, based on oxygen consumption and albumenoid ammonia, or after six KRXUV SHU FHQW SXULÂżFDWLRQ 7KH GLVVROYHG R[\JHQ DEVRUEHG E\ VKDNHQ HIĂ€XHQW LQ ÂżYH GD\V DW ƒ& ZDV RQO\ SDUWV SHU FRPSDUHG ZLWK WZR parts proposed under the British Royal &RPPLVVLRQ RQ 6HZDJH 'LVSRVDO UHSRUW It was during this time period, that ZRUN EHJDQ RQ WKH PLOOLRQ :LQQLSHJ Aqueduct, which was designed to carry RYHU P G RI ZDWHU IURP 6KRDO /DNH WR WKH :LQQLSHJ DUHD D GLVWDQFH RI RYHU NP 7KH PDJD]LQH JDYH UHJXODU coverage of the construction and of the SUREOHPV HQFRXQWHUHG 7KH WRWDO HOHYDWLRQ GLIIHUHQFH EHWZHHQ :LQQLSHJ DQG 6KRDO /DNH LV RQO\ PHWHUV 7KLV WUDQVODWHV LQWR D GURS RI DSSUR[LPDWHO\ FP SHU PHWHUV which meant the aqueduct had to be constructed with extreme accuracy in order to ensure that the elevation drop was as near to the average as possible at all WLPHV 6DLQW %RQLIDFH ZDV WKH ÂżUVW PXnicipality supplied with water from the DTXHGXFW RQ 0DUFK ,Q WKH PDJD]LQH QRWHG WKDW Henderson, Kentucky, became one of WKH ÂżUVW FLWLHV WR LQFRUSRUDWH D SUHVVXUH W\SH XOWUDYLROHW VWHULOL]HU ZKLFK KDG DQ P /d capacity in its water treatPHQW SODQW By the early twenties, a social-economic shift was gaining momentum in &DQDGD $FFRUGLQJ WR D DUWLFOH LQ WKH PDJD]LQH SHU FHQW RI WKH SRSXODWLRQ OLYHG LQ FLWLHV LQ %\ WKLV SHUFHQWDJH KDG ULVHQ WR SHU FHQW 7KLV increase, as well as an increased standard of living and a corresponding growth of industry, was causing water supply costs WR ULVH ,Q DQ DQQRXQFHPHQW ZDV PDGH WKDW WKH *UHDWHU :LQQLSHJ :DWHU 'LVWULFW ZLVKHG WR UDLVH LWV UDWHV IURP WKUHH WR ÂżYH FHQWV SHU WKRXVDQG JDOORQV D SHU FHQW LQFUHDVH ,Q WKH HDUO\ V D \RXQJ 'U $OEHUW ( %HUU\ VWDUWHG WR JDLQ SURPLQHQFH LQ HQYLURQPHQWDO FLUFOHV ,Q DQ DUWLcle by him on the value of waterworks laboratory tests was published in the PDJD]LQH ,Q LW KH ZDUQHG WKDW Âłthe operator can only be sure of the safety of the ZDWHU KLV SODQW WUHDWV E\ GRLQJ VXIÂżFLHQW laboratory tests ´ +H DGGHG WKDW Âłthe 16 | September/October 2013

WEF Past President Geoff Scott (standing) with Dr. A.E. Berry - circa 1980.

more tests employed, the greater should be the assurance of the quality.â€? $ HGLWRULDO WUDJLFDOO\ HPSKDVL]HG 'U %HUU\ÂśV PHVVDJH UHJDUGLQJ the responsibility for pure water, after a Kingswell, Ontario man successfully sued the municipality for the death of his ZLIH IURP W\SKRLG 'U %HUU\ VXEPLWWHG DUWLFOHV WR WKH PDJD]LQH RQ D UHJXODU EDVLV UDQJLQJ IURP VHZDJH GLVSRVDO LQ &DQDGD WR YHJHWDEOH JURZWK LQ ZDWHU VXSSOLHV ,Q WKH PDJD]LQH ZKLFK KDG MXVW FKDQJHG LWV name to Water & Sewage, asked “who is the most widely known waterworks man?â€? ,W WKHQ DQVZHUHG ÂłThe answer is easy. Dr. Albert Edward Berry, Chief Engineer of the Ontario Department of Health, wins in a walk. Secretary of the Canadian section AWWA; founder and secretary of the Canadian Institute on Sewage and Sanitation; director of the American Water Works Association; Chairman of the Toronto branch E.I.C.; and in supervisory charge of all waterworks and sewage treatment plants in Ontario; with full control of 750 milk pasteurizing plants in Ontario; head of a provincial research laboratory with ten engineers and chemists; author of

numerous engineering articles; winner RI WKH ÂżUVW )XOOHU $ZDUG IRU PHULWRULRXV waterworks service – Dr. Berry’s name is a synonym for knowledge and authority in sanitary engineering matters ´ One issue that arose during the mid Âľ V ZDV ZKHWKHU RU QRW WR DGG Ă€XRULGH to drinking water, as an aid in the preYHQWLRQ RI GHQWDO FDULHV :DWHU VXSSOLHV LQ FHUWDLQ DUHDV RI WKH :HVW FRQWDLQHG WRR PXFK Ă€XRULGH DQG DV D UHVXOW PDQ\ SHRSOH HQGHG XS ZLWK PRWWOHG WHHWK 6WXGLHV however, showed that, in low concentraWLRQV Ă€XRULGH ZDV EHQHÂżFLDO :DWHU VXSSO\ ZDV DOVR D PDMRU FRQFHUQ IRU PLOLWDU\ HQJLQHHUV GXULQJ :RUOG :DU ,, ZKR ZHUH UHVSRQVLEOH IRU PHHWing the huge water requirements of their UHVSHFWLYH DUPHG IRUFHV 7KH KHDGOLQH RQ RQH ZDUWLPH IHDWXUH E\ 0DMRU 3HWHU : 5DLQLHU RIÂżFHU UHVSRQVLEOH IRU ZDWHU VXSSO\ ZDV ÂłWater for Monty’s Men´ ,W was the exciting story of the indispensable part played by water supply in the WULXPSK RI WKH %ULWLVK th Army in North $IULFD ,Q WKH ODWH Âľ V HDUO\ Âľ V D IRFXV on issues, such as industrial waste and WKH QHHG IRU VDQLWDU\ ODQGÂżOO VWDUWHG WR HYROYH ,Q WKH PDJD]LQH SXEOLVKHG DQ editorial on a need for sanitary landÂżOO Âł7KH GLVSRVDO RI UHIXVH LQ ODQGÂżOOV is gaining the increasing favour of the municipal engineers, many of whom are being pressed by the growing consciousQHVV RI WKH WD[SD\HUV LQ WKH SXEOLF VLJQLÂżcance of refuge disposal. Open dumping, burning dumps and other assorted methods which give rise to nuisances from odours and smoke, provide harbourage and food for rats and insects and are a source of a number of health hazards – the cry of the citizenry, newspapers and engineers is for their removal.â€? $ DUWLFOH E\ 'U %HUU\ HQWLWOHG ÂłCanadian Practice in Sewage Works,â€? challenged the engineering profession WR PHHW WKH UHTXLUHPHQWV RI D &DQDGLan public that was fast becoming enviURQPHQWDOO\ DZDUH “Canada is in the midst of a major program of activity in WKH VHZDJH ÂżHOG 7KHUH LV DQ LQFUHDVLQJ interest in this country in the prevention of stream pollution and the maintenance of the country’s greatest natural resources, its water supplies. It is the engineer’s continued overleaf...

Environmental Science & Engineering Magazine


INDUSTRIAL

PARTS AND PARTNERS. THEY JUST HAVE TO FIT. Standard and custom fabricated pipe, delivered straight to your location. 'SPN w UP w JO EJBNFUFS QMBJO FOE UISFBEFE PS HSPPWFE PVS JOEPPS QJQF GBDJMJUZ BU PVS NBJO EJTUSJCVUJPO DFOUSF JO $PODPSE 0OUBSJP DBSSJFT UIFN BMM o BOE EFMJWFST JU *O GBDU PVS CPPN USVDLT EFMJWFS MBSHF QJQF BOE mUUJOH PSEFST BU OP DIBSHF 8F DBSSZ B DPNQMFUF MJOF PG JOEVTUSJBM 17' BOE .30 QSPEVDUT UP LFFQ ZPVS CVTJOFTT SVOOJOH TNPPUIMZ "OE ZPV DBO DPVOU PO VT UP QSPWJEF USBDFBCJMJUZ GPS UIF QSPEVDUT ZPV VTF 0VS UFBN PG JO IPVTF TQFDJBMJTUT BSF BMXBZT SFBEZ UP QSPWJEF UFDIOJDBM BEWJDF BOE TPVSDF UIPTF IBSE UP mOE QSPEVDUT UIBU XJMM NBLF ZPVS KPC FBTJFS #FDBVTF UIBU T FYBDUMZ XIBU B HPPE QBSUOFS EPFT We know your business. It’s our job.

PLUMBING | HVAC | HYDRONICS | INDUSTRIAL FIRE PROTECTION | BUILDING MAINTENANCE

OPCMF DB t


ES&E’s 25th Anniversary Special responsibility to design and construct suitable sewage systems.� Environmental activism Canadian Municipal Utilities changed its name to Water & Pollution Control in the mid 1960s to focus entirely on environmental issues. This coincided with the surge of public concern about the environment and the publication of noteworthy books such as Rachel Carson’s Silent Spring in 1962. People, who had concerned themselves mainly with gross national product and their ever-increasing living standards, suddenly realized that much of the material progress which they enjoyed had been made at the expense of the environment. A tremendous change took place in public attitudes and many protest groups made sure governments were aware of their concerns. But the new awareness caused problems for the engineering community. Engineering proposals, which earlier had been routinely rubber stamped by governments at all levels, now faced a barrage of questions by concerned and often irate citizens’ groups before any of the projects could be implemented. Many worthwhile projects were abandoned or delayed by this new sociological phenomenon of protest groups, who adroitly used both the media and governments to adapt to their mind sets. The end result of this is that Environmental Impact Assessments are now de rigueur. Larger, sometimes planetary viewpoints emerged as society realized that there were few pollution problems which operated in isolation. W&PC responded to the new challenge, with articles which were written on a much broader philosophical plane. Topics, such as eutrophication, heavy metals, acid rain, and the mutagenic effects of chemicals, were published in the following years.

the magazine’s stance on under-priced drinking water. He argued that price drove consumption. When water was undervalued, it would be wasted, leading to environmental neglect and pollution. 7KH ÂżUVW LVVXH DOVR FDUULHG DQ DUWLFOH by Ontario Environment Minister Jim Bradley about the Municipal Industrial Strategy for Abatement (MISA) program. The objective was the virtual elimination of persistent toxic substances entering the environment. It called for strict monitoring and testing programs and resulted in a surge of spending in the environmental industry. Unfortunately, government emphasis on the MISA program was short-lived when the Liberal Party lost to the New Democrats, in the 1990 election. Many analytical laboratories, which had geared up for an anticipated demand for their services due Richard Rush to the MISA program, either went out of friend: “Why don’t you launch your own business, or abandoned the environmenenvironmental magazine?â€? he enquired. tal market. He knew that both Tom and Steve DavOne key component of the Ontario ey had been editors of Water & Pollu- government’s plan to deal with toxtion Control Magazine, and that the ic substances, such as PCBs, was the creation of the Ontario Waste Management Corporation in the early 1980s. Unfortunately, the OWMC became endlessly stymied by public opposition and activist groups, opposed to the location and use of its waste incineration facility and disposal site. Ultimately, after spendDavey family worked closely with both ing some $120 million in studies, the the Water Environment Association of OWMC was abandoned, without ever Ontario and the Ontario Water Works treating even a handful of waste. Association. In the late 1980s, ES&E carried many It seemed like a good idea and, during staff-written articles advocating the use WEFTEC’87, the launch of Environ- of PCB contaminated wastes as fuels mental Science & Engineering Maga- for cement kilns. The articles stressed zine (ES&E) was formally announced. that the rotary kilns were a good idea The reaction was most favorable. because they could harness the thermal 7KH ÂżUVW LVVXH UROOHG RII WKH SUHVVHV properties of the wastes while makin February 1988 and was immediately ing cement; that the PCBs had a long HPEUDFHG E\ WKH LQGXVWU\ 7KH YHU\ ÂżUVW UHVLGHQFH WLPH LQ WKH Ă€DPH OHDGLQJ WR editorial comment by Tom Davey was almost total destruction; and that there entitled: “Why low-bid systems are bad was a saving in valuable fuel used, infor the Canadian environmentâ€?, a theme stead of conventional incineration. which touched a nerve in both consul- However, public opinion was against tants and suppliers. This issue also car- the use of PCB wastes as fuel and ried an article by Federal Environment this option was abandoned. Much of Minister Tom McMillan, which echoed continued overleaf...

People, who had concerned themselves mainly with gross national product and their ever-increasing living standards, suddenly realized that much of the material progress which they enjoyed had been made at the expense of the environment.

The founding of ES&E Magazine Many things are conceived at parties and, appropriately, it was at a publishing event in 1987 that the idea of a new environmental magazine was raised by a 18 | September/October 2013

Environmental Science & Engineering Magazine


Effective Liquid Analysis A complete digital offering in one simple, expandable and unified platform. • Simplify your analytical measurements with a unified digital platform across the entire plant. • Sensors using MemoSens technology and protocol give you true plug-‘n-play simplicity for long-term reductions in commissioning and maintenance costs. • Our completely digital platform integrates seamlessly into your control systems. www.ca.endress.com/analysis

(QGUHVV +DXVHU &DQDGD /WG 6XWWRQ 'ULYH %XUOLQJWRQ 2QWDULR / / = 7HO )D[ LQIR#FD HQGUHVV FRP


ES&E’s 25th Anniversary Special lion. This was analogous to one second in 32 million years, surely space age achievements, yet the value of laboratories was, and still may be, too often the forgotten profession in environmental remediation. Non-point pollution sources, such as oil contamination in stormwater, began to be tackled in the early 1990s. In response, sophisticated catchment systems were developed to separate and retain oil in catch basins. In the 1990s, new and improved treatment processes emerged. Membrane technology for both drinking water and wastewater developed at an astonishing UDWH 2]RQH SUREDEO\ ÂżUVW XVHG LQ &DQada in Quebec, is now used in drinking water plants in Ontario and other parts of Canada. UV disinfection too, has become a prominent tool in both drinking water and wastewater management. The 1990s brought great change to Canada’s consulting engineers. In the November 1995 issue of (6 ( George Powell, of CH2M Gore & Storrie Limited, stated that, “as the consulting industry in Ontario downsized from about LQ WR XQGHU LQ to react to the slowdown in the domestic PDUNHW WKH QHHG WR GHYHORS RSSRUWXQLties internationally grew.â€? He went on to say that, “international design/build/ RZQ RSHUDWH WUDQVIHU %227 SURMHFWV DV WKH\ DUH RIWHQ FDOOHG DUH EHFRPLQJ WKH norm.â€?

George Powell with ES&E Managing Editor Sandra Davey, circa 1990.

Walkerton Clean Water Centre.

Canada’s PCB wastes ultimately were directed to the United States. Leak detection from underground storage tanks also became an important issue in the late 1980s. In the July 1991 issue of ES&E, an article by Richard Rush and Keith Metzger, of XCG Consultants, reported that there were approximately 70,000 retail gasoline storage tanks in Canada. Studies had shown that 20-25 per cent of these were found to be, or were suspected to be leaking. “The remediation cost could be many tens of billions of dollars – the same order of magnitude as the annual Canadian FedHUDO 'HÂżFLW â€? stated the authors. The fearsome “Hole in the Ozone Layerâ€? FDXVHG ODUJHO\ E\ FKORURĂ€XRURcarbon emissions, dominated the news in the 1980s. ES&E published several 20 | September/October 2013

articles on methods to recapture CFCs, including some from Dusanka Filipovic, who played an active role in the development of an innovative technology to recapture CFCs from refrigeration and air conditioning equipment, when serviced or decommissioned. Ms. Filipovic later won several awards for her engineering work, including the Engineering Medal for Research and Development from Professional Engineers of Ontario. The ozone layer, which once dominated media coverage, is no longer as newsworthy, since it is expected to recover sometime in the 21st century. Early on, after its launch in 1988, ES&E reported in several issues on the increasingly important role of environmental laboratories and how labs could now measure toxins to parts per quadril-

Walkerton- a game changer Throughout the 1980s and 1990s, the “RXW RI VLJKW RXW RI PLQG´ attitude towards water mains and sewer lines resulted in gross neglect of cleaning, repairing and replacing this infrastructure. In 2001, this attitude changed when eight people died and some 2,000 were made seriously ill, from E. coli O157 contamination in Walkerton, Ontario’s drinking water supply. Stan and Frank Koebel were workers at the Walkerton Public Utilities Commission at the time of the tragedy. Frank worked as the water foreman, while Stan worked as the Commission’s supervisor. Both would eventually plead guilty to falsifying reports and were formally sentenced in December 2004, with Stan receiving a year in jail and Frank nine months of house arrest. FRQWLQXHG RYHUOHDI

Environmental Science & Engineering Magazine


Flush lifting handle Slam lock with SFNPWBCMF PQFOFS )PME PQFO BSN IBOEMF Stainless hinges with UBNQFS QSPPG IBSEXBSF

4UBJOMFTT MJGUJOH TQSJOH GPS TNPPUI FBTZ PQFSBUJPO

%SJQ QSPPG HBTLFUFE ESBJO DIBOOFM QSFWFOUT JOmMUSBUJPO

t "MM TUBJOMFTT TUFFM IBSEXBSF t 8FMEFE UP $4" 8 assures weld integrity

'BMM UISV QSPUFDUJPO HSBUJOH hinged, safety orange with lifting handle

t 'MVTI EFTJHO FMJNJOBUFT USJQQJOH t 4USPOH XJUITUBOET QFEFTUSJBO & occasional traďŹƒc loads

3FDFTTFE QBEMPDL IBTQ

This Is The Open & Shut Case For Hatch Standards MSU MG Safety Hatch – Sets the standard in Canada for Fall-thru Protection. Available in single, double and multi-door sizes, all welded to CSA standards by Canadian Welding Bureau certiďŹ ed welders. For hatches, made right, in Canada contact us at sales@msumississauga.com (email) 1-800-268-5336 (voice), 1-888-220-2213 (fax). Check us out on the web at www.msumississauga.com

MSU Mississauga Ltd. 2222 S. Sheridan way, Building 3, Unit 300 Mississauga, Ontario Canada L5J 2M4


ES&E’s 25th Anniversary Special Reaction to their sentencing was mixed. Some felt it was justice served, while others believed the tragedy was the result of many other factors and that it could have happened elsewhere at any time. In 2002, Justice Dennis O’Connor released The Walkerton Report, which made some 93 recommendations and added new vigour and commitment to revitalizing Canada’s water and wastewater infrastructure. Among its many recommendations was mandatory certi¿FDWLRQ ZKLFK KDV FUHDWHG D QHZ OHYHO of professionalism among water plant operators. As the Ontario government had closed down its operator training facility in the mid 1990s, mandatory operDWRU FHUWL¿FDWLRQ KDV FUHDWHG DQ RSSRUWXnity for private sector operator training. Another victim of the Walkerton tragedy was the acceptance of the land application of biosolids. Many landowners and municipalities started denying permission to do so, in order to play it safe. )ROORZLQJ D ¿UH DW D VRRQ WR EH FRPPLVsioned sludge pelletization facility, the biosolids disposal situation in Toronto

Phil Sidhwa (L) with ES&E Editor Steve Davey.

became so desperate that the city trucked LWV ELRVROLGV WR D ODQGÂżOO LQ 0LFKLJDQ 1RZ WKH *UHHQ /DQH ODQGÂżOO QHDU /RQdon, Ontario, handles Toronto’s waste. In the January 2008 issue of ES&E, Phil Sidwa of Terratec Environmental wrote that, “considering the acceptance

of recycling by society, the rejection of ODQG¿OOV DQG WKH RYHUZKHOPLQJ HYLGHQFH of climate change, the arguments raised against the land application of biosolids WKDW KDYH PHW VWULFW TXDOLW\ VWDQGDUGV DUH not realistic.� The issue of global warming, while

NASM Plan Consulting and Application of Industrial and Municipal Materials Serving municipal, industrial and commercial NASM generators across the province Services Include: ¡ Preparing Non-Agricultural Source Material (NASM) Plans for submission to OMAF ¡ Provide all preparation for NASM Plans including soil sampling, field assessments and GIS site maps in compliance with OMAF and MOE regulations ¡ Perform follow up documentation for single and multi year NASM plans ¡ Provide transport and injection application of liquid and solid NASMs

For more information please contact: Rob Alton          or PAg, CCA-CA 905-312-4095

22 | September/October 2013

Mark Janiec PAg, CCA-CA 905-878-2800 ext 223

E. terratecsales@amwater.com

W. www.terratec.amwater.com

Environmental Science & Engineering Magazine


ES&E’s 25th Anniversary Special ¿UVW UDLVHG LQ E\ 7RP 'DYH\ LQ D Water & Pollution Control Magazine HGLWRULDO FRPPHQW DJDLQ WRRN FHQWUH VWDJH LQ &DQDGD ZLWK WKH JRYHUQPHQW UDWLI\LQJ WKH .\RWR $FFRUG LQ 7KH GHEDWH RYHU KXPDQ LQÀXHQFHG FOLPDWH FKDQJH VWLOO UDJHV RQ WRGD\ :KR FRXOG KDYH SUHGLFWHG WKDW $O *RUH D IRUPHU 9LFH 3UHVLGHQW RI WKH 8QLWHG 6WDWHV ZRXOG EH KRQRUHG E\ D 1REHO 3UL]H LQ IRU KLV HQYLURQPHQWDO DFWLYLWLHV IR FXVLQJ RQ JOREDO ZDUPLQJ" 7KH :DWHU (QYLURQPHQW )HGHUDWLRQ KDV DOVR UHFRJQL]HG JOREDO ZDUPLQJ DV D NH\ LVVXH IDFLQJ ERWK WKH ZDWHU DQG ZDVWHZDWHU LQGXVWU\ ,Q &DQDGD KDG D PXFK GULHU WKDQ XVXDO VSULQJ DQG PDQ\ DUHDV H[SHULHQFHG GURXJKW OLNH FRQGLWLRQV ,Q ES&E UDQ DQ DUWLFOH DERXW 9LFWRULD % & œV LPDJLQDWLYH SXEOLF UHODWLRQV FDPSDLJQ WR UHGXFH ZDWHU FRQ VXPSWLRQ E\ SHU FHQW The Great Recession ,Q WKH VXESULPH PRUWJDJH FULVLV EURNH WKURXJKRXW WKH ZRUOG DQG VWDUWHG D SHULRG RI LQVWDELOLW\ DQG XQFHUWDLQW\ WKDW VWLOO H[LVWV 4XHVWLRQV DERXW VWLPXOXV

SURJUDPV PXQLFLSDO EXGJHWV DQG SHQ VLRQV ZHUH ZRUULHG RYHU E\ DOO LQGXVWULHV 0DQ\ LQIUDVWUXFWXUH ELG GRFXPHQWV FRQ WDLQHG WKH SKUDVH ÂłManufacturers limited to Made in USA only´ 7KXV WKH IDFWRU RI WUDGH LQ &DQDGLDQ $PHULFDQ UHODWLRQV ZDV RQFH DJDLQ D FRQFHUQ ,Q WKH )HGHUDWLRQ RI &DQDGLDQ 0XQLFLSDOLWLHV LVVXHG D UHVROXWLRQ VWDWLQJ WKDW JRRGV DQG VHUYLFHV SURFXUHG IRU ORFDO LQIUDVWUXFWXUH SURMHFWV VKRXOG RQO\ FRPH IURP FRXQ WULHV “who do not impose trade restrictions against goods and materials manufactured in Canada.â€? )HDWXUHG LQ ES&EÂśV 6HSWHPEHU LVVXH ZDV 2QWDULRÂśV 3HHO 5HJLRQ GHEDWH RYHU SLSH VRXUFLQJ IRU LWV +DQODQ :DWHU 3URMHFW 7KH SURMHFW UHTXLUHG RYHU NP RI SLSH DQG FRXQFLO ZDV GHEDWLQJ EH WZHHQ 8 6 PDGH VWHHO SLSH RU FRQFUHWH SUHVVXUH SLSH PDQXIDFWXUHG LQ 2QWDULR (YHQWXDOO\ WKH SURMHFW RSWHG WR H[FOX VLYHO\ XVH FRQFUHWH SLSH 0D\RU +D]HO 0F&DOOLDQ RI 0LVVLVVDXJD YRWHG IRU &DQDGLDQ PDGH PDWHULDOV VD\LQJ Âłwe talk about free trade, but it really isn’t and it never has been...â€? $W WKH WLPH D EXV IDFWRU\ LQ 0LVVLVVDXJD KDG MXVW EHHQ

FORVHG GRZQ ,W KDG SUHYLRXVO\ RQO\ EHHQ DOORZHG WR PDQXIDFWXUH SHU FHQW RI HDFK EXV EHIRUH WKH\ ZHUH VKLSSHG WR WKH 8 6 IRU ÂżQLVKLQJ ,Q FRQWUDVW WR D ORW RI ODERXU PDUNHWV IROORZLQJ WKH ÂżQDQFLDO FULVLV FRQFHUQV RYHU D ORRPLQJ VKRUWDJH RI SURIHVVLRQ DO HQJLQHHUV EHJDQ WR GHHSHQ DV VWXGLHV DQG UHSRUWV FDPH RXW VKRZLQJ DQ DJLQJ ZRUNIRUFH DQG D VKRUWDJH RI TXDOLÂżHG DSSOLFDQWV (DUOLHU LQ (QJLQHHUV &DQDGD SXEOLVKHG D UHSRUW VWDWLQJ WKDW WKH\ H[ SHFW SURIHVVLRQDO HQJLQHHUV WR UHWLUH E\ $WWUDFWLQJ DQG UHWDLQLQJ QHZ HQJLQHHUV KDV EHHQ GLVFXVVHG E\ ES&E IRU D QXPEHU RI \HDUV \HW WKH LV VXH VWLOO FRQFHUQV WKH LQGXVWU\ %LOO 'H$QJOLV RI $VVRFLDWHG (QJL QHHULQJ ZKR DOVR VLWV RQ ES&EÂśV WHFKQL FDO DGYLVRU\ ERDUG GLVFXVVHG VWUDWHJLHV WR GHDO ZLWK D VKULQNLQJ ODERXU SRRO LQ D 1RYHPEHU DUWLFOH “As an indusWU\ ZH QHHG WR UHVROYH WR KLUH TXDOLÂżHG foreign-trained engineers,â€? KH VDLG DGGLQJ ÂłWe need to take the time to integrate new staff into our organizations, continued overleaf...

Drive Technology \ Drive Automation \ System Integration \ Services

.(( ',%0 0 /#) /'-),%

Dynamic, versatile and effective With optimum drive solutions for all applications that require an even balance of power and precision.

Driving the world

Toronto (905) 791-1553 ¡ Montreal (514) 367-1124 ¡ Vancouver (604) 946-5535

www.esemag.com

/+, /0 !/,-(/'-0 #-/(# 0 /'')#0 -" 0 . +.. 0 0 $ 0 $ 0* & * &$ * 0 , 0* & * &$ * +++"+,-/!%..& ). )%-/!" .( September/October 2013 | 23


ES&E’s 25th Anniversary Special

Bill De Angelis

remembering that the skills they bring to us were developed in different cultural settings.� In January 2011, Engineers Canada echoed this sentiment by launched a new website aimed to help newcomers to Canada plan their engineering career. New threats With ever-increasing automation and remote management, water and wastewater treatment and environmental systems increasingly face threats from PDOLFLRXV LQ¿OWUDWLRQV $FFRUGLQJ WR WKH Repository of Industrial Security Incidents, there was a 300 per cent increase in cyber-security events in the water/ wastewater industry between 2004 and 2009. In 2010, the discovery of the Stux-

net computer worm brought wide spread attention to cyber attacks on infrastructure and industrial control systems. The worm most notably infected computers in an Iranian nuclear plant. Since 2008, ES&E has run numerous articles on the vulnerability of infrastructure, such as keeping records of people who access plants, through smart locks, RU GHYHORSLQJ LQIUDVWUXFWXUH VSHFL¿F VHcurity policies. In ES&E’s Summer 2013 issue, Victor Wong, a consulting engineer with Opus Dayton Knight, advised municipalities to re-think their security strategies. Pointing to the risks of shared networks, common communication protocols and hardware, and accessibility of training documents online, Mr. Wong warned that water system compromises are not a question of if, but when. Paying it forward Global water supply is an ever-increasing problem and ES&E has strongly supported Water For People. This charitable organization was set up to provide clean drinking water to developing countries, using appropriate, inexpensive and

> Water & Wastewater Systems > Stormwater Treatment & Management > Modeling > Hydrologic & Hydraulic Analysis > Environmental Planning > Distribution, Collection, Treatment > Hydrogeology

www.delcan.com

24 | September/October 2013

sustainable technology. Outbreaks of lethal diseases, which haunted Europe and WKH $PHULFDV IRU FHQWXULHV KDYH HLWKHU been vastly reduced in a number of developing countries, or eliminated thanks to Water For People. ES&E’s Sales Director, Penny Davey, serves on the board of Water For People Canada. Many ES&E articles have postulated that environmental engineers have perhaps done as much for public health as the medical profession. When ES&E was launched in 1988, its goal was to be a voice for Canada’s water, wastewater and environmental protection professionals. Since then, ES&E staff members have been extensively involved with and have won awards from the Water Environment )HGHUDWLRQ WKH $PHULFDQ :DWHU :RUNV $VVRFLDWLRQ WKH :DWHU (QYLURQPHQW $Vsociation of Ontario and the Canadian Business Press. ES&E intends to continue providing vigorous forums where issues affecting environmental professionals can be debated and where new technologies, projects and policies can be introduced. Tom, Steve and Peter Davey

Tom Davey: Editor, 1988 - 2008 Steve Davey: Editor, 2008 - Present Peter Davey: Editorial Assistant, 2012 - Present

Sustainable Solutions

/TTAWA s -ARKHAM s ,ONDON s .IAGARA &ALLS s #ALGARY s 6ANCOUVER s 6ICTORIA $ELCAN 625 Cochrane Drive, Suite 500 Markham, Ontario, Canada L3R 9R9 Tel: 905.943.0500 Fax: 905.943.0400 water@delcan.com

Environmental Science & Engineering Magazine



ES&E’s 25th Anniversary Special

The 5S Society - recognizing key contributors to the wastewater profession for over 70 years

T

his year marked the 30th anniversary of the founding of the Ontario Chapter of The Select Society of Sanitary Sludge Shovelers (5S). The 5S Society had its beginnings in the United States, but there is some dispute as to where and by whom it was founded. A commonly accepted thesis is that the Original Chapter of the Five S Society was formed in Arizona in October 1940. Other people strongly contend that it had its beginnings in the Commonwealth of Pennsylvania with the Ted Moses High Hat Award. Whatever its origins, independent Chapters of the Society have since been formed in British Columbia, Quebec, Ontario, Alberta, Saskatchewan and Manitoba, the United Kingdom, Australia and New Zealand, and in many of the American States. In addition, there are Shovelers in Japan, Brazil and The Netherlands. The Chapter in New Zealand is probably the youngest, having been inaugurated in May, 1993.

26 | September/October 2013

( L to R ) ES&E staffers Steve, Penny and Tom Davey are all 5S members.

It will be of interest to Canadians to know that the former Governor General, the late Madame Sauve, was made an Honorary Member of the Florida

Chapter when she spoke at the WPCF Conference in Miami in 1975. The Honourable Roger Simmons, M.P. for Burin-St. George’s was similarly hon-

Environmental Science & Engineering Magazine


ES&E’s 25th Anniversary Special oured at the Conference in Las Vegas in 1980. The Society was formed to provide a means of recognizing those who have contributed freely of their time and talents to the growth, well-being and success of their individual Associations.

some other utilitarian or decorative purpose. It must always be worn or displayed to indicate a Member in good standing, the penalty for being found without the Shovel by another shoveler being to provide all those present with a refreshment of their choice. Each Member is provided with D 0HPEHUVKLS &HUWLÂżFDWH VLJQHG E\ WKH ,QĂ€XHQW ,QWHJUDWRU DV S+ DQG E\ twelve other shovelers for the remaining concentrations from pH 1 to pH 13.

:KLOH WKH ZRUGLQJ RQ WKH &HUWLÂżFDWHV may vary from Chapter to Chapter, it normally indicates that selection to Membership is in recognition of “outstanding service above and beyond the call of dutyâ€? to the Association. Membership bestows the accolade of elevation “RQ WKH RIÂżFLDO VKRYHO WR WKH KLJKHVW ULGJH RI WKH VOXGJH EHG ZLWK WKH WLWOH RI VHOHFW VDQLWDU\ VOXGJH VKRYHOHU DQG DOO WKH KRQRXU DWPRVSKHUH SHUTXLVLWHV DQG GLJQLW\ DSSHUWDLQLQJ WKHUHWR ´

5S Society Ontario Chapter REFLECTIONS

ON THE 30th ANNIVERSARY OF THE 5S ONTARIO CHAPTER (1983 TO 2013) SPECIAL ANNIVERSARY SUPPLEMENT TO THE SPRING 2013 5S NEWSLETTER

Founding members of the 5S Society Ontario Chapter.

Many of these hard workers do not become President of their Association, or receive one of the coveted awards associated with water pollution control activities, and the Five S Society does provide a method of expressing recognition and gratitude for their efforts. It is important to appreciate that one cannot ‘’joinâ€? the Society, but that members are “selectedâ€? on the basis of merit. There are no dues for Membership in the Society, nor are there any 2IÂżFHUV H[FHSW WKH Âł,QĂ€XHQW ,QWHJUDtorâ€?, who is designated by the neutral “pH 7â€?. Those who attend wastewater association events will have seen colleagues adorned with a “Gold Shovel Emblemâ€?. It is worn as a lapel pin, tie clasp or for www.esemag.com

September/October 2013 | 27


Legal Issues

Recent no-fault orders are dumping cleanup costs on innocent parties By John Willms

W

ith little public debate and virtually no media attention, several significant legal precedents are expanding the scope and financial impact of environmental obligations. Two recent court cases illustrate how the socalled “no-fault” provisions in Ontario’s environmental laws can saddle innocent parties, both corporate and individual, with millions of dollars in remediation costs. At the same time, a bankruptcy case in Newfoundland is forcing environmental agencies to pursue these innocent “deep pockets” ever more vigorously, to fund future cleanup projects.

The Ministry had already issued a remediation Order on the responsible parties, but they had fully expended their available insurance coverage. Spilled oil had spread onto City property. Therefore, a second Order could rightfully be issued to the Kawartha Lakes, as the party that “owns or has management and control of an undertaking or a property,” even though it bore no fault for the original spill. The City’s appeal of the remediation Order was denied by the Environmental Review Tribunal. The City’s further appeal was heard by the Ontario Court of Appeal on May 1, 2013. The Court dismissed the City’s appeal.

Case #1: City of Kawartha Lakes* In 2009, the City of Kawartha Lakes was ordered by the Ministry of the Environment (MOE) to clean up a fuel oil spill it did not cause. Since then, the municipality has fought a series of legal battles to correct what it considers “a breach of natural justice.” Kawartha

Case #2: Northstar Aerospace MOE has issued orders to ensure that the directors and officers (D&Os) of a bankrupt aerospace company are personally responsible for a multi-million dollar groundwater cleanup project around one of the firm’s former plants in Cambridge, Ontario. On November 14, 2012, the Ministry issued a Director’s Order to continue remediation work against 13 former D&Os of Northstar Aerospace (Canada) Inc. and its parent company Northstar Aerospace, Inc. This was issued on the grounds that they had “management or control” of the contaminated site between 2003 and 2012. However, it is likely that most or all of the groundwater contamination occurred prior to the tenure of any of the named D&Os. The outstanding site monitoring and cleanup is expected to cost some $15 million over the next 10 years. In turn, 12 of the former D&Os have appealed the Order to the Environmental Review Tribunal (ERT) and filed a motion in the Ontario Superior Court requesting it determine the validity of the Order under the bankruptcy proceedings. The ERT appeal has yet to be scheduled. The Superior Court hearing was held April 18, 2013, and the Court has reserved judgment. In the interim, the former D&Os must continue to pay

Lakes insists that, before imposing a cleanup Order on an “innocent party,” the MOE had a duty to first consider any other persons who may have been at fault for the spill, or the off-site migration of the oil. The MOE maintains it has the discretion to issue a preventative Order under section 157(1) of the Environmental Protection Act (EPA), to ensure prompt remediation and minimize any adverse effects without regard to fault. 28 | September/October 2013

the cleanup costs, estimated at $100,000 per month. Case #3: AbitibiBowater Inc. In a closely watched case, the Supreme Court of Canada has ruled that environmental cleanup orders issued by Newfoundland and Labrador on AbitibiBowater Inc. do not have priority over other claims in the bankruptcy queue. The company, which now operates as Resolute Forest Products Inc., had instituted restructuring proceedings in 2009. Subsequently, the province filed Ministerial remediation orders for five Abitibi sites and expropriated three of the properties. The estimated costs of the cleanup ranged between $50 and $100 million. The case was heard November 16, 2011, and the decision dismissing the appeal with costs was released December 7, 2012. While the decision is specific to the particular facts of this case, we expect that environmental ministries across the country will be considering the impact of the ruling and will be revising their enforcement policies (written or informal) accordingly. The inexorable conclusion is that environmental ministries will be issuing cleanup orders sooner rather than later, ignoring questions of causation and fault. They are looking for “deep pockets” to pay remediation costs and are making claims against both a company and its directors and officers. John Willms is a partner with Willms & Shier Environmental Lawyers LLP, E-mail: jwillms@willmsshier.com

*Details of this case were outlined in greater detail in an article, also by John Willms, entitled Kawartha Lakes fights MOE order to pay for oil spill costs” which appeared in the Summer 2013 issue of Environmental Science & Engineering Magazine - www.esemag.com.

Environmental Science & Engineering Magazine



Water Loss

Managing water loss with pressure reducing valves

O

n a global basis, it is estimated that 33 billion cubic meters of treated water are lost at an estimated cost of $15 billion per year. North America seems to be lagging behind in its awareness of this issue, but is gradually catching up to the rest of the world. System losses vary by utility; however, water losses ranging from 15 to 70 per cent are common. According to the Ontario Sewer and Watermain Association, up to 30 per cent of treated water in Canada goes into the ground. When a utility undertakes a major water loss project, multiple control zones with a single source of water (if possible) are required. These zones are referred to as DMAs, or district metered areas. It is common for a mid- to large-sized utility to establish hundreds of DMAs. Assuming residential, commercial and industrial users are being metered, you now have measured flow into the DMA, as well as flow to users. There is a direct correlation between pressure and leakage. If you reduce pressure by one per cent, you will reduce leakage by approximately 1.15 per cent (subject to variation). The goal then is to develop multiple smaller DMAs within a utility and give customers just enough pressure to serve their needs, while eliminating over-pressures. Good pressure management is typically the most economical approach to reducing water loss. Each DMA requires a meter as well as a pilot-operated control valve. These valves are built to different standards worldwide and vary from manufacturer to manufacturer. Different quality materials may be used by different manufacturers. There are also many options that can be added to increase the life of these valves, or to make maintenance easier. AWWA has a standard (Standard C530) for pilot-operated control valves that is highly recommended. Here are some options for pilot-operated control valves, for reducing pressure and leakage: 1. Standard pressure reducing valves A standard pressure reducing valve (PRV)

30 | September/October 2013

By Brad Clarke

is familiar to most users. For a utility undertaking pressure management and establishing DMAs, it is often an excellent selection. This valve has typically one pilot and one pressure setting. You manually set the pilot to the one pressure you desire downstream and that is the pressure you get. Downstream pressure setting is maintained as a constant, regardless of varying upstream pressures or flow rates. This style of valve needs a differential pressure of 10 psi, or .6 bar, between the inlet and outlet of the valve to function effectively. To change pressure, the operator must adjust the valve manually by changing the pressure setting on the pilot. This style of valve works very well with medium to high system pressures. If available pressure differential drops below 10 psi (.6 bar), pressure reducing valves cannot open fully and, as the available pressure drop is further reduced, flow approaches zero. 2. Low pressure pressure reducing valves - If very low pressures are encountered during peak demand periods, standard PRVs cannot supply the required flow. If inlet pressures drop below 10 psi (.6 bar), the differential pressure across the valve is not enough to maintain the valve in the open position. Valve capacity is reduced and downstream customers may not have enough water.

This issue can be overcome by using two pilots. The first is a standard PRV pilot that is used to control or reduce pressure at non-peak usage periods. The second is a modified altitude pilot that allows the main valve bonnet to vent to atmosphere at a predetermined low pressure (usually just below the downstream set-point). When inlet pressure drops below the low pressure setpoint, the main valve opens fully. This minimizes pressure loss during peak periods. The valve can open fully, even with pressures as low as 2 psi (.13 bar). A standard PRV typically has the pilot set for the lowest pressure required at peak demand, to make sure that all users have enough pressure to satisfy their needs. Remember that the outlet pressure setting remains constant, regardless of variances in inlet pressure or flow rate. During nonpeak usage, there is less demand on the system, so pressure loss though the distribution and service mains is much less. This results in higher downstream pressures, especially in areas remote from the PRV. At non-peak times, increased pressure has two negative outcomes: leakage rates increase and pipes burst. The above scenario can be overcome in part by using two standard PRV pilots on the main valve. One pilot is set for high demand pressure (day time), while the other is set for low demand pressure (night time). A solenoid valve is sup-

Environmental Science & Engineering Magazine


Water Loss plied and a basic timing controller decides which of the two pilots is utilized. Depending on availability of power, a standard solenoid with a locally sourced timing device may be used. Alternately, if no power is available, a battery-operated timer (submersible), combined with a latching solenoid valve using minimal power, may be utilized. The above options can be very economical, with excellent results; however it is important to consider the fire department’s minimum pressure requirements. 3. Pressure reducing valves — self adjusting based on flow (pressure/flow control) - Combination pressure flow control valves can be a very interesting option. This style of valve senses flow through pressure differential across either a correctly sized orifice plate, or partially open gate valve, downstream of the PRV. The standard PRV pilot has a large secondary diaphragm operator, that adjusts the pilot setpoint based on flow. The PRV pilot is set for minimum (night) pressure. The secondary operator then increases the setpoint as the flow increases. Minimum setpoint and pressure increase are deter-

www.esemag.com

mined, to ensure adequate pressure in all parts of the DMA at peak demand. A limitation on this style of valve is that it must be a single source to a DMA. Multiple valves feeding a DMA will not function correctly. 4. Pressure reducing valves incorporating third party control — time switched or flow modulation - When utilizing this type of control, a standard PRV complete with main valve and pilot is utilized. A third party manufacturer of controllers and interface units will adapt its equipment to interface with the PRV manufacturer’s pilot. Usually a Bias chamber will be mounted under the pilot, or an actuation device will be mounted on top of the pilot, depending on the controller manufacturer. Flow modulation will react to flow variations in the system and adjust pressure accordingly. If flow modulation is not required, time-based control can be utilized with this equipment. 5. Pressure reducing valves utilizing motor driven pilot interfacing with SCADA - In this case, a sturdy slow speed 24 VDC (AC option available) motor-op-

erated device is fitted to the top of the pilot and attaches to the adjustment screw. This device requires less than 1 amp to operate and is controlled by a 4 – 20 mA signal from the water distribution SCADA system. The very low power requirement lends itself well to a solar powered self-contained station. Extended power failure would result in constant pressure at the last setting. Pressure transmitters (upstream and downstream) can be used in conjunction with flow transmitters at the DMA, so that real time data is available on SCADA. This information allows continuous adjustments of pressures based on flow demand. 6. Pressure reducing valve pre-packaged systems - Utilities are utilizing pre-packaged systems on pressure reduction stations. These pre-packaged stations make sense for use in DMAs, because they are built in a clean environment, pretested and are quicker to install on site. They can be custom designed and are often more economical. Brad Clarke is with Singer Valve Inc. E-mail: brad@singervalve.com

September/October 2013 | 31


Wastewater Treatment

Low cost installation and operation of a modified SBR system with potential for effluent reuse By John Seguire and Albert Wakim

Norwood Water Pollution Control Plant.

T

he Norwood Water Pollution Control Plant in Peterborough County, Ontario, required a treatment capacity upgrade IURP DQ DYHUDJH GD\ ÀRZ RI P3/d WR P3/d. In addition to increased ÀRZ WKH HIÀXHQW OLPLWV ZHUH UHTXLUHG to be lower than for the original plant, to meet revised discharge permit conditions and to allow for the potential reuse RI HIÀXHQW IRU LUULJDWLRQ DW D ORFDO JROI course. The original WPCP included screening, grit separation, secondary treatment with a carousel-type extended aeration (EA) plant, and chlorine disinfection. After an assessment by AECOM, the preferred upgrade option was to install a second headworks screen, a Fluidyne

ISAM SBR system.

ISAM™ (Integrated Surge Anoxic Mix) sequencing batch reactor (SBR) for secondary treatment. Aluminum sulphate would be injected into the SBR to chemically precipitate phosphorus not removed biologiFDOO\ 7RWDO VHFRQGDU\ HIÀXHQW ZRXOG EH SROLVKHG LQ D '\QD6DQG GHHS EHG ¿OWHU followed by UV disinfection, before being discharged to the Ouse River. A septage receiving station was also required, as part of the upgrade. The ISAM SBR was selected as the preferred upgrade for the secondary treatment process, on the basis of its performance, simple design and costs. In addition, there was limited space available at the site for new construction and the ISAM SBR had a smaller footprint

than the alternatives reviewed. The SBR process incorporates primary treatment, aeration, settlement and sludge wasting in one reactor, and each of these phases operates on a time-based process cycle. The combination of these phases in the SBR tanks is known as a cycle. Because the SBR process can be DGMXVWHG WR VXLW VLWH VSHFLÂżF ZDVWHZDWHU FRQGLWLRQV LW KDV YHU\ Ă€H[LEOH SKDVH DQG cycle times. ,Q DGGLWLRQ WR SURFHVV Ă€H[LELOLW\ RSerating all phases of treatment in one reactor has the advantage of lower capital and O&M costs compared to other biological treatment systems. This is due to less tankage, interconnecting pipework and process equipment usage. The ISAM SBR system was chosen Design/Build Construction Management P3 Project Delivery Maple Reinders has been delivering innovative environmental construction projects for the Canadian market for over 46 years including design, operation and private ďŹ nancing.

LORNE PARK, ONTARIO

LAC LA BICHE, ALBERTA

PICTON, ONTARIO

WTP, KELOWNA

GOLDBAR, ABERTA

www.maple.ca 1-888-416-2753 Mississauga

|

Cambridge

|

Calgary

|

Kelowna

|

Edmonton

|

Halifax

|

Vancouver

|

32 | September/October 2013

Environmental Science & Engineering Magazine


Wastewater Treatment Table l. Average influent and effluent data for 2010 to 2012 at the Norwood WPCP. Parameter

Influent

Effluent

Effluent Objectives

Flow (m3/d ADF)

544

N/Aa

N/Aa

CBOD5 (mg/L)

182

< 2.1

5

TSS (mg/L)

182

<3

5

TKN (mg/L)

32.4

N/A

N/Aa

Ammonia-N (mg/L)

N/Aa

< 0.7

0.9

Total P (mg/L)

3.9

0.08

0.2

<2

100

b

E. coli (MPN /100 mL)

a

a

N/A

Note: a. Not applicable b. Most probable number for the Norwood WPCP as it has the ÀH[LELOLW\ DQG ORZHU FRVWV RI DQ 6%5 SURFHVV ZLWK WKH IROORZLQJ DGGLWLRQDO DGYDQWDJHV • ,W LQFRUSRUDWHV DQ DQDHURELF VWDJH ,6$0 ZKHUH SULPDU\ VROLGV DQG ZDVWH ELRORJLFDO VOXGJH IURP WKH 6%5 DUH VWRUHG DQG GLJHVWHG 7KLV UHGXFHV VOXGJH SURGXFWLRQ DQG SURYLGHV D VOXGJH VWRUDJH FDSDFLW\ RI DERXW GD\V ,W DOVR DOORZV FRQGLWLRQV IRU ELRORJLFDO SKRVSKRUXV UHPRYDO • 7KHUH LV DQ DQR[LF VXUJH WDQN 6$0Œ ZKLFK DFWV DV D EDODQFLQJ WDQN DQG GHQLWULILFDWLRQ DUHD UHGXF-

LQJ HQHUJ\ FRQVXPSWLRQ IRU VHFRQGDU\ DHUDWLRQ 'XULQJ SHULRGV RI KLJKHU LQIOXHQW IORZ DQG ZKHQ WKH 6%5 WDQN LV IXOO WKH 6%5 FRQWHQWV RYHUIORZ LQWR WKH 6$0 WDQN • 7KH DHUDWLRQ DQG PL[LQJ V\VWHP XVHV D MHW DHUDWRU ZKLFK LQFRUSRUDWHV D YHQWXUL QR]]OH 7KLV UHVXOWV LQ YHU\ HIILFLHQW DHUDWLRQ ZKLFK LV QRW VLJQLILFDQWO\ UHGXFHG LQ GLUW\ ZDWHU • 7KH PHFKDQLFDO GHVLJQ LV YHU\ VLPSOH ZKLFK UHVXOWV LQ D UREXVW SURFHVV WKDW LV HDV\ WR RSHUDWH DQG PDLQWDLQ 7KH PDLQ UHDVRQV IRU WKLV DUH WKH XQFRPSOLFDWHG GHVLJQV RI WZR PDLQ PHFKDQ-

LFDO FRPSRQHQWV WKH MHW PRWLYH SXPS DQG WKH GHFDQWHU • $ MHW PRWLYH SXPS LV XVHG WR WUDQVIHU PL[HG OLTXRU LQWR WKH 6%5 WR PL[ WKH 6%5 GXULQJ WKH DQR[LF SKDVH DQG WR SURYLGH DHUDWLRQ ZLWK VXSSOHPHQWDO EORZHUV GXULQJ WKH DHUDWLRQ SKDVH 7KH GHFDQWHU LV XVHG WR GLVFKDUJH VHFRQGDU\ HIIOXHQW IURP WKH 6%5 WDQN DIWHU WKH VHWWOLQJ SKDVH 7KH SDWHQWHG GHFDQWHU V\VWHP XVHV D VLPSOH DLU ORFN FUHDWHG ZLWK D VROHQRLG YDOYH DV ZHOO DV D FRQILJXUDWLRQ WKDW GHFDQWV ODUJH YROXPHV DW D ORZ ZHLU RYHUIORZ YHORFLW\ ISAM SBR system components 7KH XSJUDGHG SODQW ZDV FRPPLVVLRQHG DQG EHJDQ RSHUDWLQJ LQ 2FWREHU $ VXPPDU\ RI KRZ WKH 1RUZRRG :3&3 KDV SHUIRUPHG RYHU WKH ODVW WKUHH \HDUV LV VKRZQ LQ Table 1 $V WKH GDWD VKRZV WKH SODQW KDV PHW DOO HIÀXHQW TXDOLW\ UHTXLUHPHQWV RYHU WKLV WLPH SHULRG 0HDVXUHPHQWV KDYH FRQVLVWHQWO\ SODFHG ZHOO EHORZ GLVFKDUJH OLPLWV VLQFH WKH SODQW EHFDPH RSHUDWLRQDO (IÀXHQW TXDOLW\ LV DFFHSWDEOH IRU UHXVH DV JROI FRXUVH LUULJDWLRQ ZDWHU EXW XQIRUWX-

For those who want it all… and more.

multiCELL controlller

ELEMENT transmitter

ELEMENT neutrino transmitter

Blind or full display performance? No matter which process instrumentation solution is the right one for you – Bürkert offers the matching concept! Whether this means our blind ELEMENT neutrino transmitters or the ELEMENT series with removable display, it‘s up to you. And if you want more, why not take a look at our multiCELL multichannel transmitter/controller – with customized display for flow and analytic measurement, as well as a generic 4-20 mA input. Want to know more? Call us at Tel. (905) 632-3033 or visit www.burkert.ca

www.esemag.com

September/October 2013 | 33


Wastewater Treatment QDWHO\ WKH FRVW RI SLSLQJ WKH HIÀXHQW KDV PDGH WKLV XQIHDVLEOH 7KHUH KDV EHHQ D VLJQL¿FDQW UHGXFWLRQ LQ 2 0 FRVWV DV D UHVXOW RI WKH XSJUDGH 6LWH YLVLWV KDYH EHHQ UHGXFHG IURP ¿YH WLPHV WR WKUHH WLPHV SHU ZHHN DQG WKH HVWLPDWHG FRVW VDYLQJ LQ ODERXU LV SHU DQQXP $OWKRXJK WKH QHZ SURFHVV KDV LQFUHDVHG WKH DPRXQW RI HTXLSPHQW UHTXLULQJ PDLQWHQDQFH WKH DXWRPDWLRQ OHQGV LWVHOI WR LPSURYHG PDLQWHQDQFH SURFHGXUHV $GGLWLRQDOO\ WKH DELOLW\ WR UHPRWHO\ PRQLWRU WKH IDFLOLW\ UHGXFHV WKH QHHG WR EH RQ VLWH DQG DOORZV IRU LPSURYHG RSHUDWLRQDO SODQQLQJ $V ZHOO DV PDLQWDLQLQJ WKH EORZHUV ZKLFK SURYLGH DLU WR WKH MHW DHUDWLRQ V\VWHP RWKHU URXWLQH PDLQWHQDQFH IRU WKH ,6$0 6%5 LQFOXGHV JUHDVLQJ WKH GHFDQWHU DQG LQVSHFWLRQ RI WKH MHW SXPSV 6OXGJH GLVSRVDO FRVWV KDYH DOVR GHFUHDVHG ZLWK HVWLPDWHG FRVW VDYLQJV RI SHU \HDU 7KLV LV EDVHG RQ DQ DSSUR[LPDWHO\ SHU FHQW UHGXFWLRQ LQ VOXGJH FRPSDUHG WR WKH ROG SODQW /RZHU VOXGJH SURGXFWLRQ KDV DOVR EHHQ UHported for other facilities operating an ,6$0 6%5 V\VWHP 7KHUH LV DOVR DQ HQHUJ\ VDYLQJ DVVRFLDWHG ZLWK WKH WUDQVIHU DQG GLJHVWLRQ RI VOXGJH 6LQFH WKH SULPDU\ DQG ZDVWH DFWLYDWHG VOXGJH DUH VWRUHG DQG GLJHVWHG ZLWKLQ WKH ,6$0 6%5 2 0 FRVWV IRU VHWWOLQJ SXPSLQJ DQG GLJHVWLQJ LW LQ VHSDUDWH SURFHVVHV DUH UHPRYHG 7KH VLJQL¿FDQWO\ ORZHU VOXGJH SURGXFWLRQ ZLWK WKLV SURFHVV DOVR UHGXFHV HQHUJ\ DVVRFLDWHG ZLWK VOXGJH PDQDJHPHQW (QHUJ\ VDYLQJV DOVR UHVXOW IURP WKH XVH RI D VHSDUDWH DQR[LF ]RQH 6$0 DQG ZLWK WKH DQR[LF FRQGLWLRQV FUHDWHG LQ WKH 6%5 WDQN GXULQJ WKH VHWWOLQJ DQG LGOH SKDVHV 7KLV LV GXH WR QLWUDWH EHLQJ XVHG LQ SODFH RI R[\JHQ GXULQJ DQR[LF FRQGLWLRQV 7KLV UHGXFHV DHUDWLRQ GHPDQGV GXULQJ WKH DHURELF WUHDWPHQW VWDJH 7KH ,6$0 6%5 GRHV QRW UHTXLUH WKH FRQVWUXFWLRQ RI D SULPDU\ RU VHFRQGDU\ FODUL¿HU RU D VOXGJH GLJHVWHU 7KHUHIRUH FRVWV DVVRFLDWHG ZLWK FRQVWUXFWLRQ LQWHUFRQQHFWLQJ SLSH ZRUN SLSHV DQG YDOYHV ZKLFK DUH SDUW RI KDYLQJ VHSDUDWH WDQNV IRU WKHVH SURFHVVHV DUH HOLPLQDWHG 7KH XSJUDGHG SODQW DW 1RUZRRG KDG ORZHU FDSLWDO FRVWV WKDQ RULJLQDOO\ HVWL34 | September/October 2013

PDWHG (VWLPDWHG SURMHFW FRVW ZDV PLOOLRQ ZKLOH WKH DFWXDO FRVW ZDV PLOOLRQ 6RPH RI WKH VDYLQJV ZHUH GXH WR ORZHU WKDQ HVWLPDWHG FRQVWUXFWLRQ FRQWUDFW FRVWV EXW D VLJQL¿FDQW IUDFWLRQ RI WKH VDYLQJ ZDV GXH WR ORZHU SURMHFW PDQDJHPHQW DQG GHVLJQ FRQVXOWLQJ IHHV ,W LV IHOW WKDW WKLV ZDV SULPDULO\ GXH WR WKH XVH RI D SDFNDJH VHFRQGDU\ WUHDWPHQW V\VWHP DQG KDYLQJ D VLJQL¿FDQW DPRXQW RI WKH HQJLQHHULQJ VXSSOLHG E\ WKH 6%5 HTXLSPHQW SURYLGHU

$OWKRXJK WKH XSJUDGH HVVHQWLDOO\ GRXEOHG WKH VL]H RI WKH IDFLOLW\ DORQJ ZLWK LQFUHDVHG FDSDFLW\ WKH RSHUDWLQJ DXWKRULW\ KDV EHHQ DEOH WR UHDOL]H FRVW VDYLQJV LQ RSHUDWRU WLPH ELRVROLGV KDXOLQJ DQG LPSURYHG HIÀXHQW TXDOLW\ GXULQJ KLJK ÀRZ SHULRGV VXFK DV VSULQJ UXQ RII John Seguire is with the Ontario Clean Water Agency. Albert Wakim is with H2Flow Equipment Inc. E-mail: DOEHUW#K ÀRZ FRP

Delcan celebrates its 60th anniversary

D

HOFDQ &RUSRUDWLRQ DQ DZDUG ZLQQLQJ PXOWL GLVFLSOLQDU\ engineering, planning, management and technology ¿UP LV FHOHEUDWLQJ LWV WK DQQLYHUVDU\ 7KH ¿UP EHJDQ LQ 7RURQWR 2QWDULR LQ DV D VPDOO ¿YH SHUVRQ FRQVXOWDQF\ 4XLFNO\ DQG VWHDGLO\ 'HOFDQ H[SDQGHG WR D FRPSDQ\ ZLWK QRZ PRUH WKDQ HPSOR\HHV LQ PXOWLSOH RI¿FHV ZRUOG ZLGH 'HOFDQ KDV PDQ\ HPSOR\HHV ZKR KDYH LQYHVWHG PRUH WKDQ \HDUV RI WKHLU FDUHHUV WR WKH ¿UP ,Q IDFW 'HOFDQ KDV EHHQ WKH KRPH WR WKUHH JHQHUDWLRQV RI WKH 5LJJV IDPLO\ 7KH ¿UVW 5LJJV IDPLO\ PHPEHU -DFN 5LJJV MRLQHG 'HOFDQ LQ )ROORZLQJ LQ KLV IDWKHU¶V IRRWVWHSV -RKQ 5LJJV MRLQHG 'HOFDQ LQ -RKQ QRZ VHUYHV DV D YLFH SUHVLGHQW PDQDJLQJ 'HOFDQ¶V /RQGRQ 2QWDULR RI¿FH -RKQ DQG KLV IDWKHU -DFN KDG WKH RSSRUWXQLW\ WR ZRUN RQ D SURMHFW WRJHWKHU DQ RSSRUWXQLW\ WKDW -RKQ YDOXHG LPPHQVHO\ DQG LV QRZ DQ H[SHULHQFH WKDW KH LV DEOH WR VKDUH ZLWK KLV VRQ 5RE 5LJJV ZKR MRLQHG 'HOFDQ LQ :KHWKHU WKURXJK SURYLGLQJ WUDQVLW V\VWHPV VWUHDP QDWXUDOL]DWLRQ DQG JUHHQ EXLOGLQJV RU WKURXJK SURMHFWV OLNH WUDI¿F PDQDJHPHQW ZDWHU HI¿FLHQF\ PHDVXUHV DQG XUEDQ SODQQLQJ 'HOFDQ KDV GHOLYHUHG VROXWLRQV WKDW FRQVHUYH UHVRXUFHV DQG HQKDQFH WKH QDWXUDO HQYLURQPHQW 7KH ¿UP¶V FRPPLWPHQW WR FRUSRUDWH UHVSRQVLELOLW\ RXWVLGH RI FRQWUDFWHG ZRUN DQG GDLO\ RSHUDWLRQV LQFOXGHV

Three generations of the Riggs family have worked at Delcan.

DFWLYH SDUWLFLSDWLRQ LQ FRPPXQLW\ RUJDQL]DWLRQV ERWK DW WKH HPSOR\HH DQG FRUSRUDWH OHYHO 'HOFDQ KDV EHHQ D ORQJ VWDQGLQJ SDUWLFLSDQW LQ YDULRXV DQQXDO IXQGUDLVLQJ SURJUDPV LQFOXGing the United Way, Water For People, &DQDGLDQ &DQFHU 6RFLHW\¶V GDIIRGLO FDPSDLJQ ORFDO IRRG GULYHV DQG PDQ\ PRUH QRW IRU SUR¿W RUJDQL]DWLRQV DV LGHQWL¿HG E\ ORFDO RI¿FHV 'HOFDQ HPSOR\HHV KDYH EHHQ H[WUHPHO\ JHQHURXV DQG UHDGLO\ GRQDWHG PRQLHV WRZDUG WKHVH FKDULWLHV DV ZHOO DV IXQGUDLVHUV IRU QDWXUDO GLVDVWHU UHOLHI LQFOXGLQJ WKH +DLWLDQ HDUWKTXDNH DQG ERWK WKH -DSDQ HDUWKTXDNH DQG WVXnami relief efforts and, most recently, WKH &DOJDU\ $OEHUWD ÀRRGV ,Q DGGLWLRQ WR VXSSRUWLQJ ORFDO FKDULWLHV LQ WKH FRPPXQLWLHV LQ ZKLFK LWV HPSOR\HHV OLYH DQG ZRUN 'HOFDQ DOVR FRQWULEXWHV HYHU\ \HDU LQ VFKRODUVKLSV IRU SRVW VHFRQGDU\ HGXFDWLRQ ZZZ GHOFDQ FRP

Environmental Science & Engineering Magazine



Drinking Water Quality

Controlling Geosmin and MIB in drinking water reservoirs and treatment plants

G

eosmin (4, 8a-dimethyl-decahydronaphthalen-4a-ol) and MIB (2methylisoborneol) are the two most common naturally-occurring contaminants that cause taste and odour (T&O) problems. Their control in source water reservoirs and at WKH WUHDWPHQW SODQW FDQ EH GLI¿FXOW DQG expensive. Although MIB and geosmin do not pose a health threat, these compounds create a displeasing earthy/musty (E/M) taste and odour when present above sensory thresholds. Often the public perceives E/M water to be unsafe or unhealthy because it is aesthetically objectionable. This creates a public relations problem for the water utility and can result in loss of consumer trust. Project objectives and approach The central objective of the Water Research Foundation’s project #3032, A Decision Tool for Earthy/Musty Taste and Odour Control, was to develop a decision-making tool to help utilities develop reasonable and defensible treatment goals for managing geosmin and MIB T&O events. This decision methodology integrates the various facWRUV WKDW LQÀXHQFH WKH GHFLVLRQ PDNLQJ process. This project covers seven E/M T&O management-related topics: 1. Summarize the occurrence, treatability, and impact of MIB and geosmin

detection limit was in the range of 5 to 10 ng/L at 25°C. Under special conditions reproducible detection levels of 2 to 3 ng/L can be measured. In terms of the T&O intensity of geosmin and MIB, most E/M T&O events in water will proGXFH ÀDYRU SUR¿OH DQDO\VLV )3$ LQWHQsities in the middle to lower half of the scale (>4). Bad taste and odours can result in the loss of consumer trust in their water utility.

on water treatment plants. 2. Conduct utility and consumer surveys to identify how utilities are currently setting E/M T&O goals and how consumers perceive E/M T&Os. 3. Evaluate the effect of background water quality on the perception of E/M taste and odour. 4. Use case studies to illustrate how some utilities have addressed longterm E/M T&O issues. 5. Use this data to develop a tool to help water utility managers navigate the decision-making process for managing geosmin and MIB in the finished water. Measurement of Geosmin and MIB The literature review investigated analytical chemistry laboratory analysis capabilities as the reproducible limits of detection. The reproducible analytical

Human sensitivity to Geosmin and MIB Odour threshold concentration (OTC) studies described in the literature review vary between one and 15 ng/L at room temperature. A range of 5 to 10 ng/L is considered to be the general public’s OTC. These values are based upon the geosmin or MIB geometric mean, where 50 percent of the population can detect WKHP )3$ LQWHQVLW\ IRU WKH 27& LV RQH An evaluation of the effect of background water quality on human sensitivity found that it did not affect the odour SHUFHLYHG E\ DQ )3$ RGRXU SDQHO IRU geosmin or MIB. However, dechlorination increased the earthy odour of geosmin and the earthy odour of the geosPLQ 0,% FRPELQDWLRQ 7KLV FRQ¿UPV the chlorine odour intensity effect, that chlorine masks geosmin (earthy) odour. However, it does not affect the musty odour of MIB. continued overleaf...

WE DO IT ALL

CORROSION PROTECTION & SEALING SYSTEMS YOU CAN DEPEND ON

Extend Structure Life, Reduce Maintenance & Repair Costs • for industrial steelwork, pipework & road surfaces • above & below ground pipe, valves, fittings & steel • offshore marine piling protection • road, bridge, airport & asphalt applications A member of Winn & Coales International.

36 | September/October 2013

www.densona.com Toronto • Edmonton Denso North America Inc. 90 Ironside Cres. Unit 12 Toronto, ON M1X 1M3 Tel: 416.291.3435 Fax: 416.291.0898

Environmental Science & Engineering Magazine


+ - . * / 0 * & 1 * .* 2 1 3 * 5 & ! ' & + )!$' 5 & "' 4 ) ( 3 / & ( / &)!/ & * " " / ( $/ ! &/ &( )!$ ( ( #" & "'/ & " " ' ' &2 #!$ (#&' 5 & ( $ & ( #"/ ' " 6 + ( & " 5 #"* -#&' 4 ( 6 ( '' & +/ ( 5 #+ &' 4 #( &- & +/ #( &- # / " ( " ) ( '( "(& ) / )& #/ * " #"(&# / ) ' 5 & ( #" 4 )& / ! & " 6 & ! / " 6 # &' ) / ' 6 %) " " / #"(&# / $ ( & 5 , &' 4 "#, 6 + " #" '/ ) # " / '( &0 " " - & ) 5 " #!$#" "(' 4 #* &'/ & '/ &#) '/ &'/ )! '/ !! &'/ "( &'/ + * # "('/ ' #$ " * '/ ( ! #& '/ )" & #* &' 5 & &' 4 & ! &- 6 #" &-/ & ) &/ " 6 (/ " " ( (( &'/ & ' " 5 # # 4 / / / / , ( #" ( / # / # 5 &( &- ( &' 4 & * " & / ' / $ #"( ")#)' + ' / ! & " 5 ' " ( #" 4 / #& " &) &'/ #& " ' #"( "! "(

5 ) " " 6 + ( & " 4 ' " &/ & * (- " &/ ( & & ''/ & + & '' 5 # -! & 4 %) " &5 #( &- # )!$' 6 & " &' 5 " &# '( &' 4 ) #" ( #" " / "3 " & " " / & (( " / ! & " ' # &'/ %) , " / )(& "( #* &5 ) &- " 4 (/ ) " # & 5 $( * " 4 & "'/ )!$ ( ( #"'/ &) '' 6 / ( ( & " 6 %) $! "( #"(&# 5 ) & (! "(/ & "'$#&( 6 (#& 4 )!$'/ #'/ " & ! '/ * #((#! #$$ &'/ )' ##&'/ &)

# " / " ( . ( #" 5 #)& #"(&# 4 " #* &'/ ! 6 # # & (! "( 5 / (#&!+ ( & 6 )!$ ( ( #"' 3 $$ " ) ('/ " " &'/ )' " ( '/ #+ ) ( " / #&( , * '/ (#&! & "' 5 '( & ' 4 ' # &'/ ' #" ( #" " 1 " 0 #!$& '' " 0 " & !#* # !# '()& / ') $ )&/ & #" #, " ' #, " / #!$ ( #3 " & ( #" ( '

! " # $ !% &&&'( ) * *' +


Drinking Water Quality Regional differences in consumer perceptions Consumer surveys were conducted at two locations (one in Florida, one in a city on the Great Lakes), both prior to and during an E/M T&O event. Trends in consumer satisfaction and perception

^ E/KZ E'/E Z

'ƾŜŜĞůů ĹśĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ? Ĺ?Ć? Ć?ĞĞŏĹ?ĹśĹ? Ä‚ ^ĞŜĹ?Ĺ˝ĆŒ ĹśĹ?Ĺ?ĹśÄžÄžĆŒ ƚŽ ĹŠĹ˝Ĺ?Ĺś ŽƾĆŒ Ĺ?ĆŒĹ˝Ç Ĺ?ĹśĹ? ƚĞĂž ŽĨ Ć‰ĆŒŽĨÄžĆ?Ć?Ĺ?ŽŜÄ‚ĹŻĆ? Ĺ?Ĺś ŽƾĆŒ EÄžÇ ĹľÄ‚ĆŒĹŹÄžĆš ŽĨĨĹ?Ä?Ğ͘ tÄž ŽĨĨÄžĆŒ Ä‚ Ä?ŽžĆ‰ÄžĆšĹ?ĆšĹ?ǀĞ Ć?Ä‚ĹŻÄ‚ĆŒÇ‡ Ä‚ůŽŜĹ? Ç Ĺ?ƚŚ Ä‚ Ä?ĞŜĞĨĹ?Ćš ƉĂÄ?ĹŹÄ‚Ĺ?Ğ͘

'ƾŜŜĞůů ĹśĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ? >ĆšÄšÍ˜ Ĺ?Ć? Ä‚ ĆŒÄ‚Ć‰Ĺ?ĚůLJ Ĺ?ĆŒĹ˝Ç Ĺ?ĹśĹ? žƾŜĹ?Ä?Ĺ?ƉĂů ĂŜĚ ĞŜǀĹ?ĆŒŽŜžÄžĹśĆšÄ‚ĹŻ ĞŜĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ? ĚĞĆ?Ĺ?Ĺ?Ĺś ĨĹ?ĆŒĹľÍ• Ć?ƉĞÄ?Ĺ?Ä‚ĹŻĹ?ÇŒĹ?ĹśĹ? Ĺ?Ĺś ĆŒĆľĆŒÄ‚ĹŻ Ć?ÄžĆŒÇ€Ĺ?Ä?Ĺ?ĹśĹ?Í• Ç Ĺ?ƚŚ ƚŚĞ Ć‰ĆŒĹ?ĹľÄ‚ĆŒÇ‡ ĨŽÄ?ĆľĆ? ŽŜ Ć?ÄžÇ Ä‚Ĺ?Äž Ć?LJĆ?ƚĞž ĚĞĆ?Ĺ?Ĺ?Ĺś ĨŽĆŒ Ä?ŽƚŚ WÄ‚ĆŒĆš Ď´ KĹśĆšÄ‚ĆŒĹ?Ĺ˝ ĆľĹ?ĹŻÄšĹ?ĹśĹ? ŽĚĞ ĂŜĚ DĹ?ĹśĹ?Ć?ĆšĆŒÇ‡ ŽĨ ŜǀĹ?ĆŒŽŜžÄžĹśĆš ĚĞĆ?Ĺ?Ĺ?Ĺś Ć‰ĆŒŽŊÄžÄ?ĆšĆ?͘ KĆľĆŒ Ć?ÄžĆŒÇ€Ĺ?Ä?ÄžĆ?Í• Ć‰ĆŒĹ˝Ç€Ĺ?ĚĞĚ ƚŽ Ć‰ĆŒĹ˝Ć‰ÄžĆŒĆšÇ‡ Ĺ˝Ç ĹśÄžĆŒĆ?Í• Ć?ĞƉƚĹ?Ä? Ć?LJĆ?ƚĞž Ä?ŽŜĆšĆŒÄ‚Ä?ĆšĹ˝ĆŒĆ?Í• Ä?ĆľĹ?ĹŻÄšÄžĆŒĆ? ÍŹ ÄšÄžÇ€ÄžĹŻĹ˝Ć‰ÄžĆŒĆ?Í• Ä?ĆľĹ?ĹŻÄšĹ?ĹśĹ? ĚĞĆ?Ĺ?Ĺ?ĹśÄžĆŒĆ?Í• Ä‚ĆŒÄ?ĹšĹ?ƚĞÄ?ĆšĆ?Í• ƉůĂŜŜÄžĆŒĆ? ĂŜĚ ĞŜĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ? ĨĹ?ĆŒĹľĆ?Í• Ä‚ĹŻĆ?Ĺ˝ Ĺ?ŜǀŽůǀĞ Ä?ŽŜĆ?Ĺ?ÄšÄžĆŒÄ‚ĆšĹ?ŽŜ ŽĨ ĆŒÄžĆ‹ĆľĹ?ĆŒÄžĹľÄžĹśĆšĆ? ĨĆŒŽž Ç€Ä‚ĆŒĹ?ŽƾĆ? Ä‚Ć‰Ć‰ĆŒĹ˝Ç€Ä‚ĹŻ Ä‚Ĺ?ĞŜÄ?Ĺ?ÄžĆ?Í• ƚŽ ĞŜĂÄ?ĹŻÄž ĆľĆ? ƚŽ Ć‰ĆŒĹ˝Ç€Ĺ?ĚĞ ƚŚĞ žŽĆ?Ćš ĞŜǀĹ?ĆŒŽŜžÄžĹśĆšÄ‚ĹŻ ĂŜĚ Ä?Ĺ˝Ć?Ćš ÄžĨĨÄžÄ?ĆšĹ?ǀĞ ĚĞĆ?Ĺ?Ĺ?Ĺś Ć?ŽůƾĆšĹ?ŽŜĆ? ĂǀĂĹ?ĹŻÄ‚Ä?ĹŻÄž Ĺ?Ĺś ƚŽĚĂLJ͛Ć? ĹľÄ‚ĆŒĹŹÄžĆšĆ‰ĹŻÄ‚Ä?Ğ͘

YƾĂůĹ?ĨĹ?Ä?Ä‚ĆšĹ?ŽŜĆ?Í— x ^Ä? Ĺ?Ĺś Ĺ?Ç€Ĺ?ĹŻ ĹśĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ?Í• W͘ ĹśĹ? x ^ŽƾŜÄš ĹŹĹśĹ˝Ç ĹŻÄžÄšĹ?Äž ŽĨ ŽŜͲĆ?Ĺ?ƚĞ Ć?ÄžÇ Ä‚Ĺ?Äž Ć?LJĆ?ƚĞž ĚĞĆ?Ĺ?Ĺ?Ĺś ĨŽĆŒ DK Θ K ^ÄžÇ Ä‚Ĺ?Äž Ć‰Ć‰ĆŒĹ˝Ç€Ä‚ĹŻĆ? Ĺ?Ć? ÄžĆ?Ć?ĞŜƚĹ?Ä‚ĹŻÍ˜ x DĹ?ĹśĹ?žƾž ŽĨ Ďł ƚŽ Ď­ĎŹ Ç‡ÄžÄ‚ĆŒĆ? Ć‰ĆŒĹ˝Ĺ?ĆŒÄžĆ?Ć?Ĺ?ǀĞ Ä?ŽŜĆ?ƾůĆšĹ?ĹśĹ? ÄžÇ†Ć‰ÄžĆŒĹ?ĞŜÄ?Äž Ç Ĺ?ƚŚĹ?Ĺś ƚŚĞ ůĂŜĚ ĚĞǀĞůŽƉžĞŜƚ ÍŹ Ć?ÄžÇ Ä‚Ĺ?Äž ÍŹ Ç Ä‚Ć?ĆšÄžÇ Ä‚ĆšÄžĆŒ ÍŹ Ç Ä‚ĆšÄžĆŒ Ĺ?ŜĚƾĆ?ĆšĆŒÇ‡Í˜ x džƚĞŜĆ?Ĺ?ǀĞ ÄžÇ†Ć‰ÄžĆŒĹ?ĞŜÄ?Äž Ĺ?Ĺś Ä?ŽŜĚƾÄ?ĆšĹ?ĹśĹ? ŽŜͲĆ?Ĺ?ƚĞ Ĺ?ĹśĆ?ƉĞÄ?ĆšĹ?ŽŜĆ? ÍŹ Ĺ?ŜǀĞĆ?ĆšĹ?Ĺ?Ä‚ĆšĹ?ŽŜĆ?Í• Ç ĆŒĹ?ĆšĹ?ĹśĹ? ƚĞÄ?ŚŜĹ?Ä?Ä‚ĹŻ ĆŒÄžĆ‰Ĺ˝ĆŒĆšĆ?Í• ĂŜĚ Ä?ŽŜĆšĆŒÄ‚Ä?Ćš ĂĚžĹ?ĹśĹ?Ć?ĆšĆŒÄ‚ĆšĹ?ŽŜ͘ x džÄ?ĞůůĞŜƚ Ĺ˝ĆŒĹ?Ä‚ĹśĹ?ÇŒÄ‚ĆšĹ?ŽŜÄ‚ĹŻ ĂŜĚ ĆšĹ?žĞ žĂŜĂĹ?ĞžĞŜƚ Ć?ĹŹĹ?ĹŻĹŻĆ?Í• ĚĞžŽŜĆ?ĆšĆŒÄ‚ĆšÄžÄš Ä‚Ä?Ĺ?ĹŻĹ?ƚLJ ƚŽ žĂŜĂĹ?Äž ĂŜĚ Ć‰ĆŒĹ?Ĺ˝ĆŒĹ?ĆšĹ?njĞ Ć?ÄžÇ€ÄžĆŒÄ‚ĹŻ Ä‚Ć?Ć?Ĺ?Ĺ?ŜžÄžĹśĆšĆ? Ä‚Ćš ŽŜÄž ĆšĹ?žĞ Ĺ?Ĺś Ĺ˝ĆŒÄšÄžĆŒ ƚŽ žĞĞƚ Ć‰ĆŒŽŊÄžÄ?Ćš ĚĞĂĚůĹ?ŜĞĆ?͘ WůĞĂĆ?Äž Ć?ĞŜĚ ĆŒÄžĆ?ƾžÄž ƚŽ͗ ĹŻĹ?njΛĹ?ƾŜŜĞůůĞŜĹ?Ĺ?ĹśÄžÄžĆŒĹ?ĹśĹ?͘Ä?Žž

Ç Ç Ç Í˜Ć?ĞƉƚĹ?Ä?ĚĞĆ?Ĺ?Ĺ?ĹśÍ˜Ä?Ä‚

may tend to be the same across markets, although the distribution of perceptions did vary as a function of market and whether or not a T&O event was occurring. Utilities need to assess their own consumer bases for perception and acceptance of E/M odours in its market. This conclusion is supported by previous studies (Mackey et al. 2003 and 2004, Zhang 1992a and 1992b). This and previous research (Mackey et al. 2003) also indicate that, while consumer surveying is a useful measure of consumer satisfaction, it is not reliable as a sole means of diagnosing T&O problems. An increase in consumer complaints can indicate a problem, but the consumer’s descriptions alone should not be relied upon to consistently and accurately diagnose the type of T&O problem. Current utility practices A small survey of 19 current utility practices found that many of the respondents did not have clearly stated treatment goals. Thirty-four percent of the XWLOLWLHV GLG QRW KDYH D VSHFLÂżF JRDO DQG 29 percent had only a qualitative E/M treatment goal, such as “not objectionable to consumers.â€? Thirty-seven percent of the utilities had a quantitative treatment goal to address E/M T&O. The goals reported were within a reasonably narrow range: geosmin goals ranged from 5 to 18 ng/L and MIB goals ranged from “not detectableâ€? (3 to 5 ng/L) to a maximum of 18 ng/L. In all cases where quantitative goals were established, the aim was to minimize, or potentially eliminate con-

sumer complaints. The participating utilities set achievable treatment goals based upon consumer perceptions in their area DQG GHWHUPLQHG VSHFLÂżF ZDWHU WUHDWPHQW goals of 10 ng/L. 6RXUFH FRQWURO FDQ EH WKH ÂżUVW OHDVW expensive control option, particularly in the watershed. Hydraulic changes, including temporarily bypassing an E/M water source, changing the raw water blend, and taking water from different levels in a reservoir, can also be low-cost methods for mitigating T&O events. The literature review and the case studies found that, when this type of mitigation is not adequate or possible, powdered activated carbon (PAC) is generally preferred when concentrations are low enough not to preclude this choice. When the events occur too often, granular activated carbon (GAC) or advanced oxidation is used. Using a decision tool to evaluate options The data reported above were used to develop an Earthy/Musty Taste &Odour Management Decision Tool. It can help utilities characterize their E/M T&O problems, identify reasonable goals for geosmin and MIB control, and develop alternative scenarios for meeting these goals (i.e., determine what processes can meet different levels of desired geosmin and MIB removal). This methodology is designed to be used in a stepwise fashion, starting with characterization of the E/M T&O problem. Then it assesses the feasibility of proven (and if desired, new) approach-

HOW WOULD YOUR POLYMER SYSTEM HANDLE THIS POLYMER GEL BALL? Eductors and wetting heads are making a comeback, but the same inherent problems still persist – poor polymer hydration and system plugging. Only the PolyBlend DD4 dry polymer system ensures a plug-free system and fully hydrated polymer. The system prepares the most concentrated solution in the shortest amount of time, least amount of space, and with low power consumption. It’s an all-around green design, but the greatest benefit is to the bottom line – no polymer wastage and fully extended polymer molecules resulting in improved process performance with the absolute least amount of polymer.

See How We Handle Polymer Gel Balls Let our experienced staff assist you in your next dry or liquid polymer makedown system design.

38 | September/October 2013

416.743.3751 indachem.com Environmental Science & Engineering Magazine


Drinking Water Quality HV WR DGGUHVVLQJ WKH SUREOHP ,W ¿QLVKHV with an evaluation of the feasible options and selection of the next step(s) in the E/M T&O management process. However, at any point in the evaluation process, if all the alternatives appear XQWHQDEOH WKH XVHU PD\ HLWKHU UHGH¿QH a portion of the scenario and start over, or jump ahead to plan the next action(s). The Microsoft Excel version of this decision methodology, included on the Water Research Foundation’s web site, leads the user through the decision process, automates many of the calculations, and facilitates development of multiple event/management scenarios. The chief goal of this tool is to help the user develop a reasonable, attainable treatment goal, so they may be confused as to why it is only Step 2 in the decision process. The tool is organized in the VSHFL¿HG RUGHU EHFDXVH VHWWLQJ D JRDO and determining the feasible options to meet it are interrelated. :KHWKHU RU QRW D GH¿QHG JRDO LV WKH correct one for a given circumstance is based in part on the feasibility of implementing the needed change(s) to the feed water–treatment plant–storage sys-

tem. Determining what system changes might be needed to meet the goal cannot be achieved before a treatment goal is proposed. This tool can be used to develop as many different event/management scenarios as desired, until a treatment goal-feasible process options scenario is reached (or until the desired range of options is assessed). Chapters One-Three describe how to navigate the methodology and describe the required information. This tool is intended to facilitate the planning process, but is not intended to replace a detailed study, pre-design, and/or master plan. T&O abatement and treatment performance technologies and DSSURDFKHV YDU\ RQ D VLWH VSHFLÂżF EDVLV Studies and design efforts are required DQG VKRXOG EH WDLORUHG WR WKH VSHFLÂżF source water(s) at a given utility. Recommendations Regardless of the control approach to minimize taste and odour problems caused by earthy/musty odours in drinking water, it is important to understand the preventative methods and the connection between the source water, the

biology of production, the chemistry and treatment processes being considered, and the water distribution system. When possible, water utilities should: • Strongly consider conducting a watershed evaluation following a significant E/M T&O event to determine the possible cause(s) and to identify possible source control options. • Develop a source water monitoring plan to facilitate detection of incipient T&O events. • Determine their own odour threshold concentrations and specific treatment goals for geosmin and MIB in their background water, with its high and low chlorine concentrations, and monitor consumer complaints. • Carefully monitor their watershed by odour panel and chemical analysis for earthy/musty odours and/or geosmin and MIB, respectively. • Develop their own E/M T&O treatment goals, based on considerations of the extent of the problem, costs, logistics, and consumer sensitivity. For more information, visit www.awwarf.org

Boost Your Productivity in Sludge Dewatering Dehydris™ Twist Boosted Sludge Dewatering Using Piston Press Technology š 9ecX_d[i fbWj[ Òbj[h fh[ii [ƎY_[dYo WdZ Y[djh_\k]Wb fheZkYj_l_jo š ;Wio ef[hWj_ed WdZ ^_]^ f[h\ehcWdY[ š 7Y^_[l[ kf je *& Zho Yedj[dj j^hek]^ Wd [dj_h[bo WkjecWj[Z fheY[ii \hec c_n[Z Z_][ij[Z ibkZ][ š Kf je )& h[ZkYj_ed _d ibkZ][ Xkba YecfWh[Z je Yedl[dj_edWb Z[mWj[h_d]

INFILCO

Infilco Degremont, Inc. – %JTDPWFSZ %SJWF 3JDINPOE 7JSHJOJB t (800) 446-1150

www.degremont-technologies.com

A partnership with Bucher Unipektin

HEADWORKS | BIOLOGICAL | SEPARATIONS | MEMBRANES | OXIDATION DISINFECTION | BIOSOLIDS | INDUSTRIAL SYSTEMS

www.esemag.com

September/October 2013 | 39


Wastewater Treatment

Installing an innovative deep-trench drip disposal system By Archis Ambulkar, Stephen N. Zeller and David Horvat

H

arford Community College in Bel Air, Maryland, hired Brinjac Engineering Inc. to replace its existing septic system with a new centralized wastewater treatment plant. This involved a recirFXODWLQJ SDFNHG PHGLD ¿OWHU FRQVWUXFWHG wetlands treatment system and an innovative deep-trench drip disposal system for groundwater discharge of the treated VDQLWDU\ HIÀXHQW 7KLV LV WKH ¿UVW DSSOLFDtion of its kind in Maryland for groundZDWHU GLVFKDUJH RI WUHDWHG HIÀXHQW The college submitted an application to the Maryland Department of Environment (MDE) for a permit to discharge a PD[LPXP GDLO\ ÀRZ RI JDOORQV SHU GD\ ZLWK JSG DYHUDJH GDLO\ ÀRZ RI WUHDWHG ZDVWHZDWHU IURP WKLV new treatment plant to groundwater. The 0'( LVVXHG GLVFKDUJH OLPLWV RI PJ O BOD PRQWKO\ DYHUDJH PJ O VXVSHQGHG VROLGV PRQWKO\ DYHUDJH DQG mg/l total nitrogen, with a groundwater discharge permit to the college. The WWTP process includes primary VHGLPHQWDWLRQ WDQNV ÀRZ HTXDOL]DWLRQ tanks and recirculating packed media ¿OWHU WR DFKLHYH %2' UHGXFWLRQ DQG QLWUL¿FDWLRQ RI VFUHHQHG VHSWLF WDQN HIÀXHQW 7KLV LV IROORZHG E\ GHQLWUL¿FDWLRQ LQ D VXEVXUIDFH ÀRZ FRQVWUXFWHG ZHWODQG system, and a drip irrigation-dosed deepbed trench disposal system. The WWTP has no above-ground components and uses wetlands for polLVKLQJ WKH HIÀXHQW DQG IRU GHQLWUL¿FDWLRQ by use of a carbon source (methanol). 7KH SURSRVHG JSG SHDN gpd) plant design estimates considered DQ DUHD RI DSSUR[LPDWHO\ DFUHV IRU WWTP construction and around six acres for the deep-bed trench disposal beds, including reserved areas and monitoring wells. Reasons for drip disposal system selection Prior to selecting a drip irrigation-dosed deep-trench system, various options were evaluated for groundwater discharge, including a pressure-dosed

40 | September/October 2013

Drip tubing in trench.

deep-trench system. However, conventional pressure dosing of deep beds would require excessive pump capacity (horsepower) as well as wet well capacity. This was due to the need to dose at proper pressure and maintain that pressure over the entire trench (approximately 96 ft.) and all discharge holes. As well, pressure dosing of this magnitude would result in very challenging hydraulics, because the site was on a gentle hill with varying slopes. Horvat Excavating recommended using a drip irrigation system at the college, which was agreed to by Brinjac Engineering and further approved by the MDE. Among the reasons for this recommendation: • Simpler design, as the drip system is less susceptible to hydraulics/grades for this site.

‡ 0RUH FRQVLVWHQW DSSOLFDWLRQ RI HIÀXent into the trenches. • Ability to use smaller pumps as dose is easier to control. • Dose is more consistent and higher-volume discharge, due to drip design. • Cleaning of drip tube is automatic. • Fewer valves/regulators for deep trenches. • Estimated cost savings of more than GXH WR UHGXFHG GHSWK RI beds, piping, pump station size, pump size, less cost for control system. The dosing regime, with drip disSHUVDO XWLOL]HV ÀRZ HTXDOL]DWLRQ WLPHG dosing, which allows operationally deWHUPLQHG DYHUDJH ÀRZ W\SLFDOO\ to be spread over a 24 hour period. The system’s operational interface allows IRU SHDN ÀRZV WR EH DFFRPPRGDWHG

Environmental Science & Engineering Magazine


Wastewater Treatment automatically by decreasing rest time EHWZHHQ GRVHV $ ÀRZ PHWHU RIIHUV DGGLtional operational monitoring. Zones can EH EURXJKW LQ DQG RXW RI VHUYLFH HDVLO\ DW the control panel, with the controller auWRPDWLFDOO\ DGMXVWLQJ GRVHV WR WKH DFWLYH zones. Design basis of drip disposal system The site layout proposed in the Onsite Sewage Disposal System Concept ReSRUW SUHSDUHG IRU WKH FROOHJH E\ DQRWKHU HQJLQHHU DQG DSSURYHG E\ WKH 0'( ZDV XVHG DV WKH EDVLV IRU GHVLJQLQJ WKH in-ground deep-trench system. The proposed drip system deep-trench area conVLVWHG RI ‡ 3ULPDU\ DUHD WKDW ZRXOG VHUYH GDLO\ ÀRZV IURP WKH ::73 XS WR gpd. ‡ 6HFRQGDU\ DUHD WKDW ZRXOG VHUYH DV D EDFNXS DV QHHGHG DQG ZRXOG SURYLGH D FDSDFLW\ RI DERXW JSG DGGLWLRQDO FDSDFLW\ DQG D UHVHUYH DUHD ZLWK FDSDFLW\ IRU IXWXUH XVH LI QHHGHG SHU 0'( UHJXODWLRQV $Q H[isting Aberdeen disposal bed on college property was proposed to handle UHPDLQLQJ JSG ÀRZV IURP WKH treatment plant, once it was remediated to eliminate high nitrogen in the groundwater. 7KLV GLVSRVDO V\VWHP LQYROYHG DQ LQ ground deep-trench absorption area, with SUHVVXUL]HG GULS WXELQJ EHLQJ XVHG IRU dosing each lateral. In the primary area, WKUHH GLIIHUHQW HOHYDWLRQV ZHUH XVHG IRU WKH ODWHUDOV GXH WR WKH VORSH RI WKH VLWH 7KLV ZDV WR NHHS WKH GHSWK RI WKH WUHQFK FRYHU WR IW PLQLPXP WKH DJJUHJDWH PLQLPXP IW EHORZ WKH ODWHUDO DQG D IW PD[LPXP WUHQFK GHSWK 7KHUH KDYH EHHQ D WRWDO RI WUHQFKHV HDFK IW ORQJ DQG IW ZLGH LQ WKH SULPDU\ DUHD DQG D WRWDO RI RI WKH VDPH VL]H LQ WKH UHVHUYH DUHD &RPSRQHQWV RI WKH GULS WUHQFK GLVSRVDO V\VWHP IRU SULPDU\ DQG UHVHUYH DUHDV LQFOXGH ‡ 'ULS WUHQFK ZHW ZHOO JDO FDpacity). ‡ 'HHS WUHQFK FRQWURO EXLOGLQJ K\GUDXOLF XQLW GLVF ¿OWHUV 89 XQLW SXPS FRQWURO SDQHO DQG GULS YDOYH FRQWUROV ‡ 6HSWLF WDQN EDFNZDVK WDQN DQG 89 recirculation pumps. ‡ =RQHV VL[ LQ SULPDU\ DQG WKUHH LQ VHFondary areas. ‡ 7UHQFKHV SHU ]RQHV QLQH www.esemag.com

‡ 7UHQFKHV LQ SULPDU\ DQG LQ VHFondary . ‡ &HOOV (DFK FHOO LQFOXGHV WZR WUHQFKHV ‡ 3LH]RPHWHUV VL[ LQ SULPDU\ DQG WKUHH in secondary areas. ‡ ,QVSHFWLRQ SRUWV RQH SHU WUHQFK ‡ 5HPRWH YDOYHV VL[ LQ SULPDU\ DQG three in secondary areas. ‡ )ORZ PHWHUV RQH IRU PHDVXULQJ ÀRZV to deep trenches. Drip system design details 7KH GULS GLVSRVDO V\VWHP ZDV SURYLG-

HG E\ $PHULFDQ 0DQXIDFWXULQJ ,WV GHVLJQ LQYROYHV VL[ ]RQHV RU FHOOV LQ WKH SULPDU\ DUHD DQG WKUHH ]RQHV IRU WKH EDFNXS or secondary area. Zones are grouped to minimize piezometers and their resulting PRQLWRULQJ ZRUN (DFK FHOO ]RQH FRQWDLQV D SLH]RPHWHU H[WHQGLQJ IW EHORZ WKH WUHQFKHV WR PHDVXUH WKH GHSWK RI WKH JURXQGZDWHU EHQHDWK :KHQ WKH JURXQGZDWHU LV ZLWKLQ IW RI WKH ERWWRP RI WKH WUHQFKHV WKH SLH]RPHWHU ZLOO VKXW RII dosing to this cell. $OO FHOOV ZHUH FRQVWUXFWHG RI Âą LQ ODW-

Introducing

Teledyne Isco’s This non-contact sensor penetrates the water with laser technology to measure velocity at multiple subsurface points Simplify your collection system monitoring with these advantages:

t No conďŹ ned space entry with mounting hardware in place

t Multipoint subsurface velocity measurement ensures quality reading without manual proďŹ ling

t Advanced submerged ow option measures in-pipe t

velocity (not single-point velocity) during surcharged conditions Bidirectional velocity measurement

Real velocity data is below the surface

.POUSFBM t 5PSPOUP t 4BSOJB t %BSUNPVUI t $BMHBSZ t 7BODPVWFS

Toll Free: 1.888.965.4700 info@avensys.com / www.AvensysSolutions.com September/October 2013 | 41


Wastewater Treatment erals, 96 ft. long with 27 drip holes per lateral, or 54 drip holes per cell. The dose per cell was determined by the elevation and OHQJWK RI WKH ODWHUDO ¿YH WLPHV WKH YROXPH RI ERWK ODWHUDOV DQG HTXDO WR WKH YROXPH of the manifold and delivery lines. With a 3 ft. head, each cell disposes of 69.12 gal/min. For a typical cell, composed of two trenches, the total dose is 355 gallons, ZLWK H[FHVV ZDWHU LQ WKH GLVWULEXWLRQ SLSH GUDLQLQJ EDFN WR WKH GRVH SXPS VWDWLRQ There are 4.17 cycles per day for the entire primary area. This disposes of the total UHTXLUHG SHDN ÀRZ RI JDO GD\ 7KH ]RQHV KDYH VXE]RQHV WR NHHS WKH LQ GRVLQJ VXSSO\ OLQHV OHVV WKDQ IW long in order to minimize friction loses. All of the laterals are composed of WZR UXQV RI OLQHDO IHHW IRU D WRWDO RI OLQHDO IHHW RI GULS WXELQJ SHU ODWHUDO 7KH GLVWDO HQG RI HDFK UXQ KDV D ORRS RI ÀH[LEOH 39& WXELQJ WR FRQQHFW WKH VHFRQG UXQV 7KLV DOORZV WKH VXSSO\ DQG UHWXUQ OLQH PDQLIROGV WR EH RQ WKH VDPH side as well as all of the delivery line and UHWXUQ OLQHV IRU HDVLHU FRQVWUXFWLRQ 7XELQJ LV WKHQ SDVVHG WKURXJK D LQ SHUIRUDWHG 39& SLSH IRU SURWHFWLRQ RI WKH WXELQJ DQG WR DOORZ WKH ZDWHU WR

42 | September/October 2013

Figure 1: Overall site layout with WWTP and deep trench area.

ÀRZ RXW 7KH HQG RI HDFK ODWHUDO SDLU RI GULS WXELQJ LQ RQH SLSH JRHV LQWR D UHWXUQ PDQLIROG WKHQ LQWR D LQ UHWXUQ SLSH WR WKH K\GUDXOLF XQLW 7KLV UHWXUQ OLQH ZLOO EH XVHG ZKHQ WKH WXELQJ LV IRUZDUG ÀXVKHG LQ RUGHU WR VFRXU WKH LQWHULRU RI WKH WXELQJ and all lines. 5HWXUQ OLQHV XVHG IRU ÀXVKLQJ DUH

LQ GLDPHWHU GXH WR WKH ORZHU ÀRZ UDWHV UHTXLUHG 7KH GULS WXELQJ LV PDQXIDFWXUHG E\ 1HWD¿Pâ„¢ $ FRQWLQXRXV VHOI ÀXVKLQJ GULSSHU GHVLJQ ÀXVKHV GHEULV DV LW LV GHWHFWHG DQG HQVXUHV XQLQWHUUXSWHG GULSSHU RSHUDWLRQ 0LFURELDO JURZWK LV FRQWUROOHG E\ URXWLQH DXWRPDWLF IRUZDUG ÀXVKLQJ RI WKH QHWZRUN

Environmental Science & Engineering Magazine


Wastewater Treatment not allow roots to enter. Drip system controls and operations (IÀXHQW IURP ZDVWHZDWHU WUHDWPHQW goes into a drip-feed duplex pump staWLRQ 7KH JDO PLQ KS WXUELQH SXPSV have check valves to keep water in the delivery lines at all times, and also to prevent the pumps from pumping through each other. They are mounted in “coolJXLGHV ´ RU ODPLQDU ÀRZ FROODUV 7KH coolguides pull water along the pump to the discharge port located in the centre of the pump to keep them cool. The HCC station has controls similar to a drip system. The heart of the drip control panel is a programmable logic controller. It controls a duplex pump station, alternating the pumps in normal operation, reverting to one pump when the Figure 2: Deep bed disposal system with trench zones. ¿UVW SXPS IDLOV 'ULS FRQWUROV SURYLGH IRU at a velocity greater than 2 ft./sec. PDLQWDLQV D FRQVWDQW ÀRZ RI JDO KU ÀRZ HTXDOL]DWLRQ ZLWK SHDN ÀRZ PDQConstruction of the RAM drip tubing RYHU SUHVVXUH UDQJHV RI WR SVL %H- agement, and have been designed to opis unique in that the internal diaphragm FDXVH WKH HIÀXHQW LV GLVWULEXWHG DW DQ XO- erate on a repeat cycle timer basis. and labyrinth provide for an exact WUD ORZ UDWH ODUJH TXDQWLWLHV RI HIÀXHQW :KHQ D ÀRDW VLJQDO WHOOV WKH FRQWURO DPRXQW RI HIÀXHQW WR EH GLVFKDUJHG IURP can be economically distributed over panel that there is enough water to beeach of its emitters, which are spaced large areas, during controlled periods of gin the dose, the timer cycles between a at 1 ft. intervals along the entire length time, without saturating the surrounding rest time (off time) and a run time (pump of the RAM drip tubing. Each emitter VRLO 7KH HPLWWHUV KDYH RUL¿FHV WKDW GR continued overleaf...

The Waterra FHT-45 high turbidity filter offers the most surface area available in a capsule designed specifically for groundwater monitoring. features • SMALL LOTS, PRE-CERTIFIED BY ICPMS • HIGH VOID VOLUME FOR LONG FILTER LIFE • MOLDED COMPOUND INLET IS STANDARD • HIGH QUALITY POLYETHERSULPHONE 0.45 FILTER MEDIA • UNIQUE OPEN PLEAT GEOMETRY FOR MAXIMUM MEDIA EXPOSURE • EACH FILTER IS PRE-RINSED WITH ONE LITRE OF DE-IONIZED WATER • MEDIUM TURBIDITY WATERRA FMT-45 & 0.2 MICRON CAP300X2 ALSO AVAILABLE

DISPOSABLE FILTERS www.waterra.com (CANADA) Waterra Pumps Limited sales@waterra.com • tel: 905.238.5242 (USA) Waterra USA Inc. waterra@openaccess.org • tel: 360.738.3366

www.esemag.com

September/October 2013 | 43


Wastewater Treatment on time). Hand off auto switches allow running of the pump valves in a manual mode. Drip controls automatically operDWH ¿HOG ÀXVKLQJ RI WKH GULS WXELQJ DQG ¿OWHUV 7KH FRQWURO V\VWHP KDV EHHQ HTXLSSHG ZLWK D ³SHDN HQDEOH´ FLUFXLW WR PDQDJH SHDN ÀRZV DQG H[FHVV ZDWHU XVH ,I WKH water level continues to rise enough to RYHUFRPH WKH SHDN HQDEOH WKLUG ÀRDW DQG WKH SHDN HQDEOH VHOHFWRU VZLWFK LV RQ ³SXPS´ RU ³SXPS DQG DODUP ´ WKH OHDG ]RQH ZLOO EH GRVHG UHJDUGOHVV RI WKH WLPH 7KH UHVW SHULRG EHWZHHQ GRVHV ZLOO EH UHGXFHG LQ RUGHU WR LQFUHDVH GDLO\ ÀRZ WR HDFK ]RQH WR RI WKH GHVLJQ ÀRZ XS IURP WKH VWDQGDUG :KHQ WKH SHDN HQDEOH FLUFXLW KDV EHHQ GHDFWLYDWHG DQG WKH FRPSOHWH ¿QDO ]RQH GRVH KDV RFFXUUHG WKH VWDQGDUG SXPSLQJ F\FOH ZLOO UHVXPH ,I WKH ZDWHU level continues to rise enough to overFRPH WKH ³KLJK OHYHO´ IRXUWK ÀRDW WKH audiovisual alarm will activate until silenced. The alarm circuit will latch until PDQXDOO\ UHVHW DIWHU WKH KLJK OHYHO ÀRDW returns to its normal position. The high OHYHO ÀRDW LV QRW D WLPHU RYHUULGH ÀRDW

Drip tubing used for trenches.

:KHQ WKH KLJK OHYHO ÀRDW DFWLYDWHV LW does not turn the pump on. 7KH FRQWURO SDQHO LV IROORZHG E\ D K\GUDXOLF XQLW ZKLFK FRQWDLQV PLFURQ GLVF ¿OWHUV WR HQVXUH WKDW QR VROLGV JR LQWR WKH GULS WXELQJ 7KH K\GUDXOLF XQLW DOVR FRQWDLQV D PDJQHWLF ÀRZ PHWHU WR DFFXUDWHO\ PHDVXUH ÀRZ 7KH VXEPHUVLEOH SXPS GHOLYHUV HIÀXHQW WKURXJK D 89 GLVLQIHFWLRQ V\VWHP LQWR HDFK ¿OWHU

$ ¿OWHU EDFN ÀXVKLQJ VFKHGXOH LV WULJJHUHG DW WKH EHJLQQLQJ RI HDFK GRVH F\FOH 2QH ¿OWHU YDOYH FORVHV EORFNLQJ WKH ÀRZ RI XQ¿OWHUHG HIÀXHQW WR WKDW ¿OWHU $IWHU D VKRUW GHOD\ WKH RWKHU ÀXVKLQJ YDOYH RSHQV EDFN ÀXVKLQJ WKH XQXVHG ¿OWHU $FFXPXODWHG LPSXULWLHV GLVFKDUJH EDFN LQWR WKH SUHWUHDWPHQW XQLW 7KLV FORVLQJ DQG RSHQLQJ SURFHGXUH RI WKH ¿OWHU DQG EDFN ÀXVK YDOYHV FDXVHV D FKDQJH

Pump Station Callouts Getting You Down? Check out the New PSL 5.0 Hybrid Pump Station Level Controller

www.greyline.com 888-473-9546 WEFTEC Booth 4502

44 | September/October 2013

Environmental Science & Engineering Magazine


Wastewater Treatment

Drip supply/return lines with solenoid, isolation, air/vacuum release valves.

RI ÀRZ ZLWKLQ WKH XQLW WR SURYLGH ¿OWHUHG ZDWHU IURP RQH ¿OWHU WR EDFN ÀXVK WKH RWKHU ¿OWHU 7KH EDFN ÀXVK SURFHGXUH ODVWV DS SUR[LPDWHO\ VHFRQGV DQG WKHQ WKH EDFN ÀXVKLQJ YDOYH FORVHV 2QO\ DIWHU WKH ¿UVW ¿OWHU KDV FRPSOHWHG LWV EDFN ÀXVKLQJ F\FOH ZLOO WKH VHFRQG ¿OWHU EHJLQ LWV F\FOH

www.esemag.com

Typical drip distribution piping with air/vacuum release valves.

RI EDFN ÀXVKLQJ LQ WKH VDPH PDQQHU V\VWHP ZDV HDV\ WR LQVWDOO DQG SURYLGHG D $V RI -DQXDU\ WKH GHHS WUHQFK VLPSOHU VROXWLRQ IRU +DUIRUG &RPPXQLW\ V\VWHP LV RSHUDWLQJ ZLWK QR SUREOHPV DQG &ROOHJH VWDII DQG PDQDJHPHQW LV SURYLGLQJ DXWRPDWHG GLVSRVDO RI HIÀX HQW 2SHUDWRUV DW WKH FROOHJH YHULI\ ZDWHU Archis Ambulkar and Stephen N. Zelle GHSWK LQ WKH SLH]RPHWHUV LI DQ\ DQG LQ are with Brinjac Engineering Inc. David VSHFWLRQ SRUWV ZHHNO\ WR PRQLWRU WKH GLV Horvat is with Horvat Excavating. SRVDO EHGV 2YHUDOO WKLV IXOO\ DXWRPDWHG E-mail: aambulkar@brinjac.com

September/October 2013 | 45


Odour Control

Effective WWTP odour control provides many benefits

T

he Swansea wasteacid scrubbing tower, followed water treatment by two sodium hydroxide/hyplant in Wales pochlorite scrubbers (pH9 and was constructed in pH11). The emission discharge 1996 to meet the stringent limit of H2S was set at 70 ppb. European Union tests for A number of sporadic odour Swansea Bay. At the time, complaints had been investiit was deemed to be one of gated and were determined to the most technologically coincide with the plant’s doors advanced wastewater treatbeing opened. In 2006, the ment plants in the world. chemical scrubber developed The plant was constructed a leak and extensive refurbishpartially below ground, so as ment/replacement was going to to be virtually invisible from be required. inland. The works included The Terminodour Air Handling Unit installed at Swansea Client options and process an activated sludge plant; Bay WWTP. selection work in the whole of Wales. inlet screening; primary, With the chemical scrubber The plant is designed to handle requiring major refurbishment of the secondary and tertiary treatment prior to UV disinfection; and discharge via a a population equivalent of 165,000. scrubber vessels, the client requested Due to its close proximity to residen- Imtech to investigate potential options. long sea outfall into Swansea Bay. The plant is owned and operated tial areas, careful attention was paid to As well, poor air quality issues within by Dwr Cymru Welsh Water, who odour control and twin-train three-stage the building that had led to the doors appointed Imtech Process (formerly 70,000 m3/hr chemical scrubbers were being opened, were to be investigated. MEICA) as their process contractor used. The following options were actively Each train consists of a sulphuric considered: partners, to carry out all new upgrade

46 | September/October 2013

Environmental Science & Engineering Magazine


Odour Control

The Terminodour system was installed at Swansea WWTP’s lamella areas, inlet works and FOG areas.

• Refurbish/replace and increase volumetric flow through the chemical scrubber. • Replacement of the primary lamella tank covers. • Septicity control applied to the incoming sewer.

• A Terminodour positive pressure ionisation system. Replacement of the primary lamella tank covers was eliminated, due to the lack of manpower available on-site to constantly remove and replace the covers for sludging and backwash arrangements.

Septicity control was eliminated, as the operational cost of dosing was unsustainable. Refurbishment/replacement of the existing chemical scrubber was technically an acceptable solution, but capital costs were high and the limitations on improving the extraction rate were considerable. Terminodour had a relatively low capital cost and very low operational costs, but was unproven on a project of this magnitude. However, it had worked successfully at several smaller Dwr Cymru Welsh Water sites. Imtech decided to carry out a trial of Terminodour in the primary lamella tank area of the building, which was the area of most concern in the plant. If the trial was successful, it would be installed throughout the building. Process description The Terminodour™ system is located in an Air Handling Unit (AHU) situated within the building. The AHU is manufactured from double-skin galvanised mild steel (stainless steel is continued overleaf...

For over two decades SPD Sales team has remained dedicated to the promotion; supply and support of instrumentation and chemical feed products for the process control market. Our highly trained and qualified personnel provides full technical application and product support to industries and municipalities, putting forward the highest quality products and instrumentation solutions for our clients. We build strong, long lasting partnerships with our clients by providing comprehensive product support and calibration services.

64 Northam Drive Mississauga, ON L4V 1J2 Phone: (905) 678-2882 Fax: (905) 293-9774 Email: sales@spdsales.com www.sp ds al es. co m TF: 800-811-2811

www.esemag.com

September/October 2013 | 47


Odour Control Performance testing

Location:

Average H2S (ppm)

Maximum H2S (ppm)

TWL:

2.00

22.00

Handrail:

0.15

0.66

% Reduction:

92.5%

97%

Table 1. Results from OdaLog gas monitors.

an option), with a foam core providing acoustic insulation and protection from the elements. Air is drawn in through external louvers by heavy duty fans, mounted within the AHU and then filtered to remove particulates. Air is then fed into the plasma reactor section, where it flows over corona discharge tubes and oxygen molecules are ionised. Ionised air is then fed via stainless steel ductwork into the lamella tank area. When the negatively charged oxygen ions meet the positively charged hydrogen sulphide ions, a collision occurs

and oxidation reaction commences. No separate ventilation system is required for the building, as the Terminodour system provides ventilation and odour abatement. The process is ATEX certified, for operation in explosive atmospheres. Performance testing The primary lamella area was sectioned off from the rest of the building and the Terminodour system was installed. OdaLog gas monitors were installed just above the top water level (TWL). Another

See us at WEFTEC 2013 Oct. 4 - 9, Booth 2679

KSB Service - skills you can count on KSB Pumps Inc. has expanded its service facilities to provide you with a full range of service repair options for your pumps, regardless of the manufacturer. Hard-to-find spare parts? No problem, we have the resources to locate or re-manufacture everything you need. Technology that drives success!

www.ksb.ca Pumps Valves Systems

48 | September/October 2013

set of monitors were located on the handrail approximately 1.5 m above the lower logger. The criteria for success were determined to be an 80 per cent reduction in odours between the two logger points. The results are detailed in Table 1. The operators’ favourable response, combined with the successful performance test data, led to CSO Technik being awarded the balance of the contract. Terminodour was then installed to service the inlet screenings, the fats, oil and grease area, the aeration tanks, and the outfall area. Post installation review The system has run effectively for several years and the following benefits have been noted: • The system continues to provide effective odour control and no complaints were received. • Capital cost of the system was less than 50 per cent of refurbishing the chemical scrubber. • Operators no longer have to wear breathing apparatus to carry out their duties. • The client has been able to reclassify and downgrade hazardous areas. • Corrosion within the building, particularly to the control panel busbars and wiring, which were being replaced every six months, has been eliminated. • Maintenance is minimal but carried out by CSO Technik under a quarterly service agreement. • Operational costs have been drastically reduced. Kusters Water is the exclusive distributor of Terminodour in North America. For more information, E-mail: jim.weidler@kusterszima.com

Environmental Science & Engineering Magazine


Wastewater Treatment

Improving nitrification at a WWTP with variable loading By Duane Forth, Dave Chapman and Tim Howarth

T

he Caledonia Wastewater Treatment Plant services the Town of Caledonia (Pop. approx. 9,600) and has a nominal design capacity of 7,200 m3/d. It uses a conventional activated sludge process ZLWK ÀRZ HTXDOL]DWLRQ WHUWLDU\ ¿OWUDWLRQ HIÀXHQW FKORULQDWLRQ GH FKORULQDtion, chemical addition for phosphorus removal and aerobic sludge digestion. A septage receiving station handles private holding tank, septic tank and portable toilet wastes from the local DUHD 7UHDWHG HIÀXHQW IURP WKH SODQW LV discharged into the Grand River, and is required to meet monthly averages for concentrations of cBOD5 (25 mg/L), TSS (25 mg/L), TP (0.3 mg/L), and ammonia (1 mg/L from May to November and 2 mg/L from December to April). A consultant study in 2006 recommended that the plant be de-rated to 4,600 m3/d. In October 2008, a Compre-

Al Campbell (operator) using a sludge judge to take a core sample from clarifier. Dave Chapman and Jim Matthews, CPO Inc., provided technical assistance – training.

hensive Performance Evaluation (CPE) was conducted and the liquid train was

rated as capable of meeting the nominal design capacity of 7,200 m3/d.

(AVE YOUU EVER L R LOOK OOK OKKED E AT AT THE AT THE HEE TRUE COST OF OWNE N RSHIP FORR YOUR LIFT SSTATIONS N 7HE 7HEN YYOU SEE BE 7HE B YOND INITTIAL PU PURCH RCHASE AS PRICE TO OOTHER LIFIFE C E CYCL YCL C E COST STS L ST S IKE INSTALLA LL TIOON N PUM MP EFlCIENCCY AND PPOWE WERR D R DRA DRAW RAA O

OPERATION AND A MA MAINTENA ENANCE NCE

ASSOCIATTED LABO ABOR T R TIME IME AN A D EEQUI U PMENT AND PPART AR S S YOU YOU WI WILL LL APPRECIA IATE THEE 3MI 3M TH , OVE , OVELLESS APPR P OACCH /UR /UR OP OPERA ERATOR TOR SAFE ABBOVE VE GRA GRADE DE 7ET 7E DE 7 LL -OUNTED 0UMPP 3T 3TATITIONS NS WI WITH TH LONG LAASTING NG HIGH GHLY LY EFl EFllCIE CIENT NT 3 , 3 , .O 3 . N #LOG 0U 0UMPS MPS DE DELIV LIVER ER THE LOW WEST LLIFT ST STATI ST ATION ATI O OPEERAT ON R ING CO C STS n INC INCLUD UDING ING SAVINGGS VVS SUB SUBMER MERSIB MER SIBLES SIB ES

#!,, 6)3)4 3MITHAND,OVELESS COM

www.esemag.com

3EE FOR YOURSELF 2EQUEST A VIEW AT YOUR FACILITY WITH A VISIT FROM ONE OF OUR TRAVELING DEMO 0UMP 3TATIONS AT 3MITH!ND,OVELESS COM

September/October 2013 | 49


Wastewater Treatment 7KH DQQXDO DYHUDJH GDLO\ ÀRZ ZDV RI WKH QRPLQDO GHVLJQ FDSDFLW\ DQG WKH SODQW PHW HIÀXHQW FRPSOLDQFH LQ DOO PRQWKV HYDOXDWHG +RZHYHU WKH DYHUDJH PRQWKO\ HIÀXHQW DPPRQLD ZDV PDUJLQDOO\ FRPSOLDQW LQ VHYHUDO RI WKH PRQWKV UHYLHZHG 7KH ::73 IDLOHG WR PHHW FRPSOLDQFH IRU HIÀXHQW DPPRQLD IRU WKUHH PRQWKV LQ $V VXFK WKHUH ZHUH FRQFHUQV WKDW WKH H[LVWLQJ SODQW FRXOG FRQVLVWHQWO\ DFKLHYH HIÀXHQW DPPRQLD FRPSOLDQFH DV ORDGV LQFUHDVHG 7KHUH ZDV DOVR D ODFN RI FODULW\ FRQFHUQLQJ WKH FDSDFLW\ RI WKH H[LVWLQJ IDFLOLW\ DQG WKH QHHG IRU IXWXUH XSJUDGHV $ WHFKQLFDO DVVLVWDQFH SURJUDP ZDV LQLWLDWHG LQ -XQH WR GHWHUPLQH WKH FDXVH RI YDULDEOH HIÀXHQW DPPRQLD FRQFHQWUDWLRQV EHWWHU GH¿QH WUXH SODQW FDSDFLW\ DQG LGHQWLI\ SURFHVV ERWWOHQHFNV LPSDFWLQJ SHUIRUPDQFH (QKDQFHG PRQLWRULQJ WRWDO PDVV FRQWURO DQG GDWD WUHQGLQJ ZHUH LQLWLDWHG ZLWK RSHUDWLRQV VWDII 5RXWLQH 3URFHVV &RQWURO 0HHWLQJV 3&0V ZHUH KHOG DW WKH SODQW WR UHYLHZ GDWD WUHQGV GLVFXVV LVVXHV LPSDFWLQJ SHUIRUPDQFH DQG LGHQWLI\ DQG GRFXPHQW IROORZ XS $ GHVLJQ FRQVXOWDQW ZDV UHWDLQHG WR LGHQWLI\ RSWLRQV DQG FRVWLQJ WR LPSURYH

Al Campbell takes a mixed liquor sample.

WKH SODQW¶V KHDGZRUNV SURYLGH VWHS IHHG XSJUDGH WKH GLJHVWHUV HWF 'HVSLWH LPSURYHPHQWV LQ SURFHVV FRQWURO DQG PRQLWRULQJ HIÀXHQW DPPRQLD FRQFHQWUDWLRQV VSLNHG WR DQ DYHUDJH RI PJ / LQ -XO\ 'XULQJ WKLV XSVHW LW ZDV REVHUYHG WKDW VHFRQGDU\ HIÀXHQW DONDOLQLW\ GURSSHG WR QHDU ]HUR ZKLOH S+ GHFUHDVHG WR V X %HFDXVH HDFK PJ / RI 7RWDO .MHOGDKO 1LWURJHQ 7.1 UHTXLUHV PJ / RI DONDOLQLW\ WR QLWULI\ LW ZDV VXVSHFWHG WKDW WKH DONDOLQLW\ LQ &DOHGRQLD¶V UDZ VHZDJH ZDV QRW VXI¿FLHQW IRU FRPSOHWH QLWUL¿FDWLRQ ZKHQ KDXOHG VHZDJH LV DGGHG 6XEVH-

TXHQWO\ HIIRUWV IRFXVHG RQ LGHQWLI\LQJ DQG UHVROYLQJ ORZ DONDOLQLW\ DQG S+ LVVXHV WR LPSURYH WKH FRQVLVWHQF\ RI QLWUL¿FDWLRQ %HQFK VFDOH WHVWV ZHUH FRQGXFWHG LQ 6HSWHPEHU WR GHWHUPLQH LI LQKLELWRU\ VXEVWDQFHV LQ WKH UDZ VHZDJH RU ODFN RI DONDOLQLW\ ZHUH WKH FKLHI FDXVHV RI XSVHWV 7KH VWXG\ FRQFOXGHG WKDW WKH KDXOHG VHZDJH ZDV QRW LQKLELWRU\ EXW GLG VLJQL¿FDQWO\ LQFUHDVH 7.1 ORDGLQJ WR WKH SODQW ,W DOVR HVWDEOLVKHG RSHUDWLQJ JRDOV RI D PLQLPXP RI PJ O DONDOLQLW\ DQG D S+ RI V X LQ WKH VHFRQGDU\ HIÀXHQW 2SHUDWRUV LQLWLDWHG URXWLQH PHDVXUHPHQWV RI DONDOLQLW\ DQG S+ LQ WKH VHFRQGDU\ HIÀXHQW DQG PDQXDOO\ DGGHG EDJV RI VRGD DVK VRGLXP FDUERQDWH WR WKH SULPDU\ HIÀXHQW ZKHQ OHYHOV IHOO EHORZ RSHUDWLQJ JRDOV 'XULQJ WKH VXPPHU RI WKH\ DGGHG VRPH NJ RI VRGD DVK SHU GD\ 'XH WR WKH DPRXQW RI PDQXDO ODERXU LQYROYHG LQ DGGLQJ VRGD DVK D WULDO ZDV FRQGXFWHG XVLQJ VRGLXP DOXPLQDWH LQ SODFH RI DOXPLQXP VXOSKDWH DOXP IRU SUHFLSLWDWLQJ SKRVSKRUXV $OXP FRQVXPHV PJ / RI DONDOLQLW\ IRU HDFK PJ / DGGHG 0HWFDOI DQG

TOGETHER, MEETING THE CHALLENGES OF CLEAN WATER Are you looking for ways to improve your water treatment quality, to remove more TOC and THMs, to increase your filter runs or to generate less sludge? Kemira can help you solve these challenges and much more. At Kemira, we aim to be a leading water chemicals supplier for raw and waste water applications, serving municipalities and water intensive industries. Together with our customers, we apply our knowledge and expertise to develop innovations that address the sustainable future of water. Tel. +1 800 465 6171 or +1 450 652 0665 info.canada@kemira.com www.kemira.com

50 | September/October 2013

Environmental Science & Engineering Magazine


Wastewater Treatment Eddy 2003). In contrast to alum, sodium aluminate is strongly alkaline and therefore does not consume alkalinity. Sodium aluminate has a percentage of aluminum-ion of 10.7%, in comparison to 4.3% for liquid alum. As sodium aluminate is more expensive than alum on a per unit volume basis, the trial compared dosages and costs to those for alum and supplementary soda ash. For an eight week period in the fall of 2011, the performance of alum with supplementary soda ash dosed to one train was compared to sodium aluminate dosed to the second train. Results indicated that sodium aluminate was an acceptable alternative to alum. Subsequently the entire plant was switched to sodium aluminate for total phosphorus control in November 2011. The plant operated with only sodium aluminate from November 2011 until the end of June 2012. Then, supplemental liquid caustic (sodium hydroxide) ZDV DGGHG WR PDLQWDLQ VHFRQGDU\ HIÀXent alkalinity above the operating goal of 50 mg/L Conclusions The addition of hauled sewage conWULEXWHG WR SRRU QLWUL¿FDWLRQ SHUIRUPDQFH %HQFK VFDOH QLWUL¿FDWLRQ WHVWV determined that the hauled sewage was not inhibitory. High concentrations of TKN in the hauled sewage exerted an alkalinity demand which exceeded that of the raw sewage. 1LWUL¿FDWLRQ UDWHV GURSSHG ZKHQ VHFRQGDU\ HIÀXHQW S+ GHFUHDVHG EHORZ and ceased entirely at a pH of 5.7 s.u.. 7R DFKLHYH HIÀXHQW DPPRQLD FRQFHQWUDtions below 1.0 mg/L in the summer and 2.0 mg/L in the winter, operating goals RI PJ / DONDOLQLW\ DQG V X S+ had to be maintained in the secondary HIÀXHQW DV PLQLPXPV Soda ash addition was successful in PDLQWDLQLQJ VHFRQGDU\ HIÀXHQW JRDOV for pH and alkalinity but was labour intensive. Substituting alum with sodium aluminate for phosphorus removal ZDV VXFFHVVIXO LQ DFKLHYLQJ HIÀXHQW phosphorus concentrations and mainWDLQLQJ HIÀXHQW S+ DQG DONDOLQLW\ RSerating goals. However, supplemental pH and alkalinity control was still required during the summer when inÀXHQW 7.1 FRQFHQWUDWLRQV ZHUH KLJKHU www.esemag.com

Figure 1 is a trend graph of effluent ammonia concentrations for a three and a half year period.

and alkalinities were lower. 9DULDEOH QLWUL¿FDWLRQ SHUIRUPDQFH was not related to lack of unit process capability and the plant did not need to be de-rated. lnvolving operators in the technical assistance program and chemical dosage study was critical to

ensuring sustainability of the results. Duane Forth is with Veolia Water Canada. Tim Howarth is with Haldimand County. Dave Chapman is with CPO Inc. For more information, E-mail: duane.forth@veoliawaterna.com

TORNADO® Heavy Duty Rotary Lobe Pumps Designed for the highest Operational Reliability with low life cycle costs, maintenance in place, and featuring NETZSCH GSS-Technology - a positive separation between product and gear box.

3 Ranges 12 Models 0 - 4400 gpm NETZSCH, the world market leader with 60 years of experience and over 500,000 progressing cavity pump installations worldwide. With sales, production and service on 6 continents ensuring customer support to provide NETZSCH Pumps & Systems - Solutions you can trust

Learn more.

NETZSCH Canada, Inc. Tel: 705-797-8426 email: info@netzsch.ca www.netzsch.ca September/October 2013 | 51


Drinking Water Treatment

Evaluating the removal costs of hexavalent chromium in drinking water

C

hromium typically occurs in two oxidation states in the natural environment, water treatment processes and water distribution systems: trivalent chromium (chromium-3, Cr(III), Cr+3), and hexavalent chromium (chromium-6, Cr(VI), Cr+6). Trivalent chromium has been considered an essential human nutrient. Recent studies, however, have shown no deleterious effects from low Cr(III) in the diet and there is no known biological mechanistic function for Cr(III) in cells. This calls into question whether Cr(III) is truly an essential nutrient (Di Bona et al. 2011). Hexavalent chromium has been demonstrated to be a human carcinogen when inhaled. Its health effects through ingestion, which is the dominant exposure route for drinking water, are currently under review. Hexavalent chromium in drinking ZDWHU ZDV ÂżUVW EURXJKW WR WKH SXEOLFÂśV attention in 1993 when Erin Brockovich highlighted contamination in groundwater near Hinkley, California. In 2010, the Environmental Working Group (EWG) reported trace levels of hexavalent chromium in 31 of 35 U.S. tap waters tested. Although this was not a peer-reviewed VFLHQWLÂżF VWXG\ LW GLG UHQHZ SXEOLF LQterest in hexavalent chromium. USEPA is currently considering whether or not to establish maximum FRQWDPLQDQW OHYHOV 0&/ VSHFLÂżFDOO\ for hexavalent chromium. A February

Hexavalent chromium contamination was the subject of the bio-pic movie “Erin Brockovich� which starred Julia Roberts.

2011 U.S. congressional hearing, which was largely focused on the EWG study, further highlighted the hexavalent chromium issue. The goal of this review is to better inform potential regulatory action on this issue by summarizing what is known about hexavalent chromium, as well as pointing out gaps in current knowledge. Health effects Decades of epidemiological studies have shown that occupational exposure of workers in various industries (electroplating, chrome pigment, mining, leather tanning, and chrome alloy production) to

Figure 1. Potential range of national annualized cost of Cr(VI) treatment to various treatment goals. 52 | September/October 2013

airborne hexavalent chromium posed increased risks of lung cancer. Assessments of the carcinogenic potential of inhaled hexavalent chromium are summarized in the Integrated Risk Information System (IRIS) for chromium (USEPA, 1998), Kimbrough et al (1999), and references in IARC (1990). In early 2012, the Water Research Foundation partnered with the American :DWHU :RUNV $VVRFLDWLRQÂśV :DWHU ,QGXVtry Technical Action Fund to fund WaterRF project #4432, National and California Treatment Costs to comply with Potential Hexavalent Chromium MCLs. This project was a collaborative effort amongst Chad Seidel and Chris Corwin of Jacobs Engineering Group Inc., Issam Najm of Water Quality & Treatment Solutions, Inc., and Nicole Blute and Xueying Wu of Hazen and Sawyer. Approach To conduct the cost estimates, the research team used data analyzed in another WaterRF project, Total Chromium and Hexavalent Chromium Occurrence Analysis, to identify entry points (EP) with reported Cr(VI) and total chromium levels. Five potential Cr(VI) treatment goals were considered: 1, 2, 5, 10, and 20 Îźg/L. The team then developed treatment capital and operations and maintenance (O&M) costs as a function of EP size for each of four technologies: UHGXFWLRQ FRDJXODWLRQ ÂżOWUDWLRQ 5&) strong base anion exchange (SBA),

Figure 2. Potential range of California annualized cost of Cr(VI) treatment to various treatment goals. Environmental Science & Engineering Magazine


Drinking Water Treatment weak base anion exchange (WBA), and reverse osmosis (RO). Treatment costs were based on a combination of engineers’ estimates, information from existing plants where available, and EPA cost equations. Previous work at Glendale Water and Power was particularly helpful for this task, and D ¿QDO UHSRUW RQ WKLV ZRUN was submitted to the California Department of Public Health. For each EP size and target Cr(VI) level, the treatment technology with the lowest annualized cost was then determined. National costs were estimated by summing the costs of treatment systems for all EPs. Results National cost estimates ranged sigQL¿FDQWO\ GXH SULPDULO\ WR WZR IDFWRUV uncertainty in occurrence data and different waste handling scenarios. For each treatment option, one scenario for waste handling was a simple and lower cost option, and the second was a complex and higher cost option, resulting in upper and lower limits for cost estimates. Figure 1 presents the potential range of the annualized cost for each Cr(VI) treatment goal based on the combination of the ranges under both Scenarios One and Two. Annualized costs were calculated as the sum of the annual O&M cost and the amortized capital cost. For a Cr(VI) goal of 20 Οg/L, the national annualized cost may range from $300 million/yr to $1.2 billion/yr. For a Cr(VI) goal of 1 Οg/L, the national annualized cost may range from $7.1 billion/yr to $82 billion/yr. Annual O&M costs comprise approximately 50% of the annualized costs for each Cr(VI) treatment goal under Scenario One and approximately 50–80% under Scenario Two. These increase with lower treatment goals, due to the more stringent requirements for residuals handling and disposal. &DOLIRUQLD FRVW HVWLPDWHV EHQH¿Wed from more robust occurrence data, thereby reducing one level of uncertainW\ EXW FRVW HVWLPDWHV VWLOO UHÀHFW D UDQJH due to uncertainties regarding different waste handling scenarios. Figure 2 presents the potential range of the California annualized cost for each Cr(VI) treatment goal based on the combination of the ranges under Scenarios One and Two. For a Cr(VI) goal of 20 Οg/L, the www.esemag.com

California annualized cost may range from $80 million/yr to $120 million/yr. For a Cr(VI) goal of 1 Οg/L, the California annualized cost may range from $2.6 billion/yr to $8.4 billion/yr. The report noted that these estimates are based on limited information, and PDQ\ NQRZOHGJH JDSV ZHUH LGHQWL¿HG during the course of the analysis. Occurrence data from EPA’s Third Unregulated Contaminant Monitoring Rule will greatly help tighten national estimates. All of

WKH HVWLPDWHV ZRXOG EHQH¿W IURP DGGLtional treatment studies on waters with different water quality conditions. WaterRF’s project, Impact of Water Quality RQ &U 9, 5HPRYDO (I¿FLHQF\ DQG &RVW is addressing this need and includes an online cost calculator for utilities. Several ongoing Tailored Collaboration projects are also investigating Cr(VI) treatment. )RU PRUH LQIRUPDWLRQ YLVLW www.awwarf.org

PREVENT MICROBIAL INDUCED CORROSION

Microbial Induced Corrosion and Water Infiltration are two major problems common to sewage collection systems. Whether for new construction or rehabilitation, Xypex Crystalline Technology is a most effective and permanent solution. Worldwide, in both sewage collection and wastewater treatment structures, Xypex has been proven to cost effectively mitigate chemical attack in severe biochemical conditions and prevent water infiltration even under extreme hydrostatic pressure.

www.xypex.com September/October 2013 | 53


Wastewater Treatment

Popular Quebec lakefront lodge gets new highperformance wastewater treatment system By Roger Lacasse

S

aint-Hippolyte’s Auberge du Lac Morency resort is nestled in the heart of the Laurentian Mountains, 50 minutes north of Montreal. Built in 1934 on the shores of Lake Morency, it welcomes thousands of visitors every year. Over the years, the resort has grown into an international holiday destination, prized by ecologically-minded travellers for its environmentally-friendly approach to lodging and its first-rate, locally grown and sustainable gourmet fare. The owners share a long-time commitment to protecting the natural surrounding habitat with their guests, who are invited to make easy eco-gestures to limit the environmental impact of their stay. Challenges Installed almost 20 years ago, the existing intermittent sand filter septic system treated wastewater generated from different sources, such as the dining room’s kitchen, the spa and approximately 40 rooms and 60 condo units. However, it had reached

Auberge Morency in Saint-Hippolyte is located on the shores of Lake Morency in the Laurentian Mountains.

Installed almost 20 years ago, the existing intermittent sand filter septic system treated wastewater generated from different sources, such as the dining room’s kitchen. the end of its useful life and began to show signs of failure. Final effluent discharge into a nearby stream, leading to Lake Morency and then into Lake L’Achigan, was deemed harmful to the sensitive watercourse and had preoccupied the local lake association for some time. The nature of the site’s geology prevented any infiltration. Additionally, space available for a new installation and access to the mountainous setting was quite limited. Therefore, the owners required an ultra compact system, which could be delivered to the site partly pre-packaged. Also, its footprint had to pose minimal restrictions to the popular outdoors activities offered year-round at the resort. The solution called for an on-site, high-performance wastewater treatment system, offering exceptional levels of effluent quality and stable treatment performances, including disinfection, nitrogen reduction and phosphorus removal. The solution would have to be permanent, low maintenance and offer top treatment performance for many years. Solution High-quality effluent produced by EcoprocessTM Membrane Bioreactor from Premier Tech Aqua met the strictest quality requirements for discharge. This was as much for the reduction of 54 | September/October 2013

The final footprint of the treatment plant, including raw sewage lift station, primary treatment and balancing tank is 518 m2.

The three pre-packaged, rotomolded tanks inside the 90 m2 building house the membranes.

organic matter and suspended solids as for tertiary treatment. Membrane filtration units and the electro-mechanical components were delivered to the site in prefabricated modules to Environmental Science & Engineering Magazine


Wastewater Treatment ensure simple, high-quality installation. The building housing the MBR treatment technology, measures just over 90 m2 and was easily integrated into the surrounding environment. The footprint of the complete treatment plant, including the raw sewage lift station, primary treatment and balancing tank, covers a total surface of 518 m2. Table 1 shows data provided by Roy & Vézina Associés, which Premier Tech Aqua used to design the Ecoprocess MBR. These parameters are for a daily maximum flow of 70 m3/d and a temperature of 16°C The environmental discharge objectives for this project’s final effluent are shown in Table 2. Treatment performance levels offered by the Ecoprocess

Wastewater generated from the kitchen flows first through a grease trap to retain fats, oil and grease and then to individual septic tanks. Membrane Bioreactor are shown in Table 3. Complete treatment process Wastewater generated from the kitchen flows first through a grease trap to retain fats, oil and grease and then to individual septic tanks. Each tank is equipped with an effluent filter to retain a certain percentage of suspended solids. A pumping station for the clarified wastewater collects and carries it from all the septic tanks to an equalization tank. It has an effective volume of 23.3 m3 with eight hours retention time. Two of the three pumps installed inside the equalization tank are dedicated to feeding the membrane bioreactor. The other is used to recirculate water to the sludge storing tank for phosphorus removal. Ecoprocess MBR technology One membrane bioreactor, of an approximate effective volume of 41 m3, is separated into four compartments. The first compartment is equipped with fine bubble diffusers, which provide oxygen for biological wastewater treatment. The effective volume of the basin is 26 m3. The three other compartments operate in parallel and serve as membrane ultrafiltration tanks that clarify the wastewater. Each ultrafiltration tank is 5 m3 and holds a flat sheet membrane with an effective surface of 100 m2. Three pumps withdraw permeate out of the bioreactor and redirect it to a perforated pipe covered by crushed stone. The treated water then flows by gravity into the watercourse. Biological and chemical sludge are pumped into a storage tank. The operating cycles of the biological aeration, self-scouring, mechanical and chemical backwash of the membrane, are controlled by a state-of-the art central panel, specifically designed for this application. Telemetry is also available. The treatment system, installed and commissioned by Premier Tech Aqua in the spring of 2013, is designed to ensure the simplicity, reliability and robustness required for on-site wastewater treatment. Roger Lacasse is with Premier Tech Aqua. For more information, E-mail: lapa2@premiertech.com www.esemag.com

Parameters

Concentrations

Carbonaceous biochemical oxygen demand (CBOD5)

252 mg/L

(Total suspended solids) TSS

131 mg/L

Total phosphorus (Ptot)

12 mg/L

Table 1. Data used to design the Ecoprocess MBR.

Parameters

Concentrations

CBOD5

≤ 15 mg/L

TSS

≤ 15 mg/L

Fecal coliforms

≤ 200 CFU/100 mL

Ptot

≤ 0.5 mg/L

Table 2. Discharge objectives for the final effluent.

Parameters

Annual average concentration at effluent

CBOD5

≤ 5 mg/L

TSS

≤ 10 mg/L

Fecal coliforms

≤ 200 CFU/100 mL

Ptot

≤ 0.1 mg/L

Table 3. Treatment performance levels offered by Ecoprocess MBR.

Toronto • Kitchener • Kingston Edmonton •

Halifax • Cincinnati

XCG Consultants provides innovative, practical & sustainable environmental solutions in:

Municipal Infrastructure

Wastewater & Water Treatment

Water Resources

Site Assessment

Solid Waste

Remediation & Risk Assessment sessmen ment

Hazardous Materials als Management Mana nag ent

Training & Operations rations ns

www.xcg.com

ore information. ormat atio Visit xcg.com for mor more

September/October 2013 | 55


Infrastructure Management

Helping agencies cope when a storm hits

T

he rainfall event that hit the Greater Toronto Area on July 8, 2013, exceeded the 1 in 100 year return period in many areas. Total rainfall in some areas exceeded 110mm within a two hour period. The timing and intensity of the storm had immediate and long-term impacts on the region. Serious disruption to commuters ZDV FDXVHG E\ VXUIDFH ÀRRGLQJ ÀRRGHG highways, limited public transport and even a partially submerged two-storey passenger train. The lasting impacts, which are not always easy to identify and quantify, were ÀRRGLQJ WR EXVLQHVVHV DQG KRPHV DQG ZDVWHZDWHU RYHUÀRZ LQWR WKH HQYLURQPHQW 7KHVH HQYLURQPHQWDO DQG ¿QDQcial consequences are generally caused by the inability of stormwater infrastructure to cope with large rainfall events. A UDLQIDOO HYHQW LV GH¿QHG DV D UDLQIDOO YROXPH SUHFHGHG DQG IROORZHG E\ D VSHFL¿F dry period. With large storm events such as the one on July 8 being reported more frequently, people are looking for answers as to why their homes and businesses DQG FRPPXWHU URXWHV DUH EHLQJ ÀRRGed. In the current age of information, 24-hour media coverage and connection through social media, municipal and government agencies are being pressured to quickly respond to hazardous

Serious disruption to commuters was caused by surface flooding, flooded highways, limited public transport.

environmental events. The senior management of such agencies rely on their support departments to help inform the public and to understand the extent of the rainfall in these large storms. Cole Engineering Group Ltd. from Markham, Ontario, is leading the way in real-time environmental monitoring and analytic solutions in the Greater Toronto Area. Working collaboratively with the Cities of Toronto and Mississauga and the Region of Peel, they have been able to streamline the data collection and analysis process of rain gauge networks. The importance of real-time rainfall

monitoring could not have been greater during and after the excessive rainfall on July 8. 7KH ÂżUP ZDV DEOH WR SURYLGH WKHLU clients with alarms to operations staff during the event, followed by meaningful analysis within a number of hours. Using a combination of rain gauges equipped with wireless cell technology and dynamic spatial analysis tools, Cole Engineering was able to provide the agencies in the area with graphical representations of rainfall distribution across the area. The speed with which this infor-

Serving Ontario’s Consultants & Contractors

1-855-586-3545 56 | September/October 2013

Soil Sampling Gas Probes & Monitoring Wells Injection Well Installations Well Maintenance Decommissioning Soil Cuttings Removal Mobile Water Treatment

LandsharkDrilling.ca Environmental Science & Engineering Magazine


Infrastructure Management

Total Rainfall Depth Distribution.

mation can be collected, analyzed and distributed is critical when informing stakeholders looking for answers. Graphical representation, often referred to as a rainfall map or isohyetal map, allows the viewer to quickly and easily understand rainfall distribution and pinpoint the worst affected areas. Given the right setup, the analysis can be comSOHWHG DQG YHULÂżHG ZLWKLQ KRXUV RI rainfall events. The density and connectivity of a

www.esemag.com

Maximum 120 Minute Intensity Distribution.

rainfall network are critical components in meeting current expectations. Its main purpose, in terms of managing an urban centre, is to correlate rainfall with the VXUIDFH ZDWHU JHQHUDWHG &RQÂżGHQFH LQ the rainfall data and its distribution over space and time is an important part of this correlation. Numerous studies have been conducted to investigate the effects of rain gauge density on the accuracy of the data captured. Rainfall is extremely variable in both space and time. As

such, large variations in intensity and volume across geographical areas have been documented, especially during extreme rainfall. There is no right or wrong level of rain gauge distribution density; however, it should be directly linked to the value of assets within the network’s coverage. The Cities of Toronto and Mississauga and the Region of Peel are leading the way for urban centers, with continued overleaf...

September/October 2013 | 57


Infrastructure Management one rain gauge per 20 km2. To put that in perspective, the United Kingdom, said to be the leading country in terms of rain gauge density, has one gauge for every 76 km2. 7KH EHQH¿WV RI D OLYH UDLQ JDXJH network include the speed of analysis, detection of early warning alarms and remote diagnostics. A live setup is achieved by integrating the rain gauge and logger into the available wireless cell network. There are numerous rain gauge technologies that offer different levels of sophistication. The sophistication of the setup should match the vulnerability of the geographical area, ranging from logging-only setups in uninhabited areas, to real-time setups in a downtown city core. Real-time rain gauge capabilities FDQ EH D YDOXDEOH SDUW RI D ÀRRG SURWHFtion system, tracking a storm as it moves across a vulnerable area. Operation and maintenance of a UDLQ JDXJH QHWZRUN FDQ DOVR EHQH¿W from real-time setups. Custom alarms FDQ EH FRQ¿JXUHG WR LQIRUP WKH UHPRWH operator that an equipment problem is

A rainfall event is defined as a rainfall volume preceded and followed by a specific dry period.

impending, or has occurred. This helps to increase the duration between regular maintenance visits and reduce the downtime of a rain gauge. Rainfall maps are also powerful tools following damaging rainfall events. The graphical representation allows for quick and easy assimilation by lay-

persons or engineers. Improved quality control, quick analyses and a real-time setup, give senior management of municipal and government agencies the FRQ¿GHQFH WR LQIRUP WKH FRQVWLWXHQWV RI the magnitude of a rainfall event. This helps alleviate public uncertainty, or XQUHVW IROORZLQJ D ÀRRG 7KH LVRK\HWDO

%LVKRS :DWHU 7HFKQRORJLHV ,QF Bishop Water Technologies are the Agents/Distributors for Tencate GeotubeÂŽ in Eastern Canada. With over 15 years combined experience, we are Canada's leader in GeotubeÂŽ installations for sludge management. Our focus is on the development and implementation of simple, cost effective, environmentally responsible sludge management solutions for our clients.

Our Cutting Edge Technologies

x GeotubeÂŽ Technology x Advanced Biofilm Wastewater Treatment

x Chemical Treatment x Lagoon Sludge Profiling x Bacteria and Enzymes x Engineering Solutions x Leasing Options

STORMWATER STORAGE MODULES • Easy to Install & Clean • 97% Void Space • High Strength • Stackable • 18, 24, 30 or 36" Heights

www.bishopwater.ca

Phone: 610-236-1100 Email: stormwater@brentwoodindustries.com Web: www.brentwoodindustries.com

58 | September/October 2013

Environmental Science & Engineering Magazine


Infrastructure Management map also offers great value to the planning, design and management of water resources. Isohyetal maps spatially represent UDLQIDOO DPRXQWV RYHU D VSHFL¿HG GXUDtion. Simply a contour map of rainfall, they use colour ramps and contour lines, to represent distribution of rainfall across a geographical area. The two most common forms are the total rainfall volume and the peak rainfall intensity. The total rainfall volume map is the total rainfall recorded for a single rainfall event. The peak rainfall intensity map, which offers greater engineering value, is the representation of peak rainfall volXPH RYHU D VSHFL¿F WLPH SHULRG 7KH LQtensity map is used in a similar way to the traditional intensity-duration-frequency (IDF) curves. It compares measured rainfall intensity to that of a statistically derived return period. The intensity map allows engineers to quickly understand the distribution of rainfall across any given catchment. This becomes a powerful tool when trying to make sense of D PHDVXUHG ÀRZ UHVSRQVH LQ VWRUPZDWHU

management structures and conveyance systems. It allows engineers to underVWDQG ZK\ ÀRRGLQJ RFFXUUHG LQ RQH DUHD and not another. Cole Engineering’s isohyetal mapping tools rely on custom back-end data management processes to ensure that the ¿QDO UDLQIDOO PDS FDQ EH TXLFNO\ PRGL¿HG WR PHHW HQJLQHHUV¶ QHHGV 7KH SURcess stores the original data and generates maximum peak intensities for multiple durations. This back-end process JUHDWO\ VSHHGV XS WKH ¿QDO JHQHUDWLRQ of meaningful rainfall maps, especially when selecting the appropriate duration for a given catchment. The selected duration should closely match the time of concentration (maximum duration of ÀRZ WKURXJK D FDWFKPHQW RI D FDWFKment being analyzed. The mapping process uses Geographical Information Survey (GIS) geoprocessing tools to create both the rainfall surface and rainfall contours. Techniques such as Thiessen polygons, polynomial interpolation, spline interpolation and Kriging, can be used to interpolate be-

tween rain gauges and create the rainfall surface. Studies have been conducted to measure the appropriateness of each interpolation method. Factors such as rain gauge density and topography affect the accuracy of the different methods. Cole Engineering is looking to a cloud based rainfall mapping solution to circumvent these resource issues. This will supplement their existing web based environmental data management and analysis tools. The July 8, 2013 event was an eye-opener for many people on how destructive rainfall can be. However, by KDYLQJ VXI¿FLHQW FRYHUDJH RI UDLQ JDXJes which provide data in real-time, understanding the impact and being able to make quick decisions is achievable. This also allows for the creation of detailed and informative maps that allow all parties to understand both the challenges and the bigger picture when it comes to managing exceptional rain events. For more information, E-mail: cstebbing@coleengineering.ca

Supplying a wide range of test kits and instrumentation for the detection and quantification of contaminants in soil, waste, water and air; ensuring your data quality objectives are met.

DO pH ORP COND TDS

SRB CO2 H 2S LEL TEMP

Western Regional Office 100, 18130-105 Avenue NW Edmonton, AB T5S 2T4 Phone: 1-800-560-4402 sales@ospreyscientific.com

www.esemag.com

PCP PAH PCB BTEX TPH

Pesticides Turbidity Toxicity Salinity Nutrients

Eastern Regional Office 3620B Laird Road, Unit 7 Mississauga, ON L5L 6A9 Fax: 1-877-820-9667 www.ospreyscientific.com

September/October 2013 | 59


Wastewater Instrumentation

New developments in tuning the accuracy of lift station flow rates

W

DVWHZDWHU XWLOLWLHV ¿QG WKHPVHOYHV IDFHG ZLWK LQFUHDVLQJO\ WLJKW EXGJHWV DQG PXVW VHDUFK IRU FRVW HIIHFWLYH ZD\V WR PRQLWRU DQG UHFRUG OLIW VWDWLRQ ÀRZ UDWHV $V ZDVWHZDWHU FROOHFWLRQ V\VWHPV DJH LW EHFRPHV LPSRUWDQW WR DFFXUDWHO\ PRQLWRU LQÀRZ DQG LQ¿OWUDWLRQ , , DW OLIW VWDWLRQV (QJLQHHUV DQG XWLOLW\ PDQDJHUV UHO\ KHDYLO\ RQ WKH DFFXUDF\ RI GDWD WR PDNH VRXQG GHFLVLRQV WR LPSURYH DQG PDLQWDLQ WKHLU V\VWHP¶V HI¿FLHQF\ 9ROXPHWULF ÀRZ PHDVXUHPHQW WHFKQLTXHV DUH DPRQJ WKH VLPSOHVW DQG PRVW DFFXUDWH PHWKRGV IRU PHDVXULQJ ÀRZ %XW FDOFXODWLQJ YROXPHWULF OLIW VWDWLRQ

SXPSLQJ FDSDFLWLHV WR SURGXFH LQÀXHQW ÀRZ UDWHV PD\ EH PLVOHDGLQJ 3XPS FDSDFLWLHV FRQVWDQWO\ FKDQJH GXH WR DSSOLHG KHDG SUHVVXUH DQG SXPSLQJ FRQGLWLRQV 2QO\ WXQLQJ DQG XSGDWLQJ SXPS FXUYHV ZKLOH UHDFWLQJ WR WKHVH FKDQJLQJ FRQGLWLRQV FDQ LPSURYH YROXPHWULF ÀRZ DFFXUDFLHV 7KH 9ROXFDOF 6\VWHP IURP 0DLG /DEV XWLOL]HV VRIWZDUH WR WXQH SXPS FDSDFLWLHV EDVHG RQ YROXPHWULF LQÀXHQW UDWHV 7KLV V\VWHP UHTXLUHV D GDWD ORJJHU WR VWRUH WKH SXPS F\FOH DQG YROXPHWULF GDWD ,W PDNHV WXQLQJ DQG UHWXQLQJ SXPS FDSDFLWLHV SRVVLEOH 9ROXFDOF ZDV DEOH WR DFKLHYH RYHUDOO DFFXUDFLHV RI “ SHU FHQW KRZHYHU WKLV DFFXUDF\

The Volucalc System from Maid Labs utilizes software to tune pump capacities based on volumetric influent rates. This system requires a data logger to store the pump cycle and volumetric data. It makes tuning and retuning pump capacities possible. 60 | September/October 2013

VHHPHG WRR ORZ IRU D WXQHG SXPS FDOFXODWLRQ 3DUW RI WKH GLVFUHSDQF\ UHVWHG ZLWK WKH VRIWZDUH¶V DOJRULWKP $LPLQJ WR DGGUHVV WKH ORZ SHUFHQWDJH IRU WXQHG ÀRZ PRQLWRULQJ %HQRLW %HDXGRLQ RI 0DLG /DEV WHVWHG KLV DOJRULWKP ZLWK SHUIRUPDQFH VRIWZDUH WKDW HPXODWHG W\SLFDO ÀRZ UDWHV JHQHUDOO\ VHHQ LQ OLIW VWDWLRQV 7KH VRIWZDUH HPXODWLRQV LQFOXGHG LQÀXHQW ÀRZ UDWHV EDVHG RQ WLPH RI GD\ DQG GHULYHG UDLQIDOO DV , , events %HDXGRLQ¶V UHVHDUFK IRXQG WKDW LQ PRVW FXUUHQW FDOFXODWLRQV LQFOXGLQJ GUDZGRZQ WHVWV 6&$'$ V\VWHP¶V WLPH VWDPSHG GDWD ZKLFK XVH WKH PDQXIDFWXUHU¶V SXPS FXUYHV ZHUH LQDFFXUDWH 0RVW OLIW VWDWLRQV FROOHFW LQÀRZ LQ D ZHW ZHOO DQG SXPS OLIW LW WR WUDYHO WKURXJK D JUDYLW\ V\VWHP 0DQ\ XWLOLWLHV KRZHYHU XVH IRUFH PDLQV RU FRPELQH JUDYLW\ IRUFH PDLQ V\VWHPV WR WUDQVSRUW HIÀXHQW ÀRZ WR ZDVWHZDWHU WUHDWPHQW SODQWV 9DULDEOHV UHODWHG WR SXPSLQJ FDSDFLWLHV DOVR QHHGHG FRQVLGHUDWLRQ WKHVH SXPS FDSDFLWLHV FDQ YDU\ EDVHG RQ VL]H KRUVHSRZHU DQG W\SH RI SXPS V LQVWDOOHG $OVR PRVW OLIW VWDWLRQV ZLOO H[SHULHQFH D ZLGH UDQJH RI HOHFWULFDO LVVXHV IURP VWDUWHUV FRQWDFWRUV DOWHUQDWRUV DQG DVVRUWHG UHOD\V ZKLFK DIIHFW WKH DFFXUDF\ RI ÀRZ FDOFXODWLRQV 0DLG /DEV DOVR IRXQG XQGHU DQG over-designed station pumping capacLWLHV ZKLFK LPSHGHG IRUFH PDLQ SUHVVXUHV WKURXJKRXW FROOHFWLRQ V\VWHPV 7KLV GRHV QRW HYHQ DFFRXQW IRU WKH FRQVWDQW DOWHULQJ RI LQÀXHQW ÀRZ UDWHV RU WKH GUDZGRZQ VLSKRQ HIIHFWV RQ HDFK F\FOH RI WKH OLIW VWDWLRQ 2QFH GHYHORSHUV DW 0DLG /DEV XQGHUVWRRG ZK\ WXQHG ÀRZ V\VWHPV SURGXFHG UHVXOWV ZLWK RQO\ “ SHU FHQW DFFXUDF\ WKH TXHVWLRQ ZDV WKHQ KRZ WR RYHUFRPH WKHVH G\QDPLF SURSHUWLHV 'HYHORSHUV NQHZ WKH VDPH ROG GUDZGRZQ WHVW ZRXOG QR ORQJHU EH VXI¿FLHQW ,W IDLOHG WR DFFRXQW IRU FKDQJHV LQ WKH LQÀXHQW UDWHV WKH IRUFH PDLQ SUHVVXUHV WKH GUDZGRZQ HIIHFW RU WKH VLSKRQ HIIHFW 'HYHORSHUV KDG WR DGMXVW IRU WKH VLSKRQ HIIHFW WKH GUDZGRZQ HIIHFW WKH

Environmental Science & Engineering Magazine


Wastewater Instrumentation possibility of mismatched pumps, the VXEPHUVLRQ RI LQÀXHQW SLSHV WKH FDSDFLW\ YROXPH RI LQÀXHQW SLSHV HWF Maid Labs had to do much more to their software to provide overall accuUDF\ 3DVW SURGXFW VXFFHVVHV ZRUNHG WR the advantage of researchers, as it gave them the ability to review hundreds of UDZ GDWD ¿OHV $UPHG ZLWK WKLV LQIRUmation and dozens of lift station videos, Maid Labs’ research and development team determined that the original emulation software produced calculated data WRR VLPSO\ WR SURYLGH DFFXUDWH WHVWV Beaudoin’s original algorithm was ULJKW MXVW OLPLWHG 6R KH FUHDWHG D QHZ DQG KLJKO\ YHUVDWLOH DOJRULWKP :KDW began as a single white board with the original algorithm, expanded to eight white boards of mathematical equations, designed to continuously tune SXPS FDSDFLWLHV The result of Maid Labs’ research and development team’s efforts, is a FRPSOH[ EXFNHW DQG VWRS ZDWFK DOJRULWKP WKDW VXFFHVVIXOO\ WDNHV WKH G\QDPLF QDWXUH RI OLIW VWDWLRQV DQG ÀRZ UDWHV LQWR DFFRXQW 7KH UHVXOWLQJ 0HUmaid system is a lift station performance

The Mermaid system produces usable results.

DQDO\]HU ZKLFK FDOFXODWHV DYHUDJH ÀRZ rates within two per cent of a standard PDJQHWLF ÀRZ PHWHU ,W DOVR SURYLGHV critical data on the electrical perforPDQFH DQG HI¿FLHQF\ RI WKH OLIW VWDWLRQ LQ WKH SURFHVV ,Q DGGLWLRQ WR DGGUHVVLQJ WKH FRQcerns of utilities’ budget restrictions, the Mermaid system follows government guidelines for cost-effective and enviURQPHQWDOO\ HI¿FLHQW ÀRZ PRQLWRULQJ $ FROOHFWLRQ V\VWHP¶V HI¿FLHQF\ LV QRW MXVW DERXW ÀRZ UDWHV ,W LV WKH FRP-

ELQDWLRQ RI DFFXUDWH ÀRZ GDWD SXPS capacities, head losses and horsepower, ZKLFK SURGXFHV XVDEOH UHVXOWV 7XQLQJ WKH DFFXUDF\ ZLOO SURYLGH NH\ GDWD IRU , , VWXGLHV K\GUDXOLF PRGHOLQJ DQG OLIW VWDWLRQ HI¿FLHQFLHV The Mermaid system is being used by utilities across Canada and the UnitHG 6WDWHV DQG LV DYDLODEOH IURP $YHQV\V 6ROXWLRQV For more information, E-mail: lclement@3spgroup.com

TOXIC GAS SHUTOFF Water For People is dedicated to creating reliable access to safe drinking water, improved sanitation facilities, and hygiene education programs in Africa, Asia, Central America, and South America.

It’s not enough to help some but not others. In the regions where we work, we are committed to providing access to every person–today and in the future–and we monitor our work for at least 10 years post-implementation to guarantee its impact.

Water For People–Canada De L’eau Pour Tous–Canada

Water For People-Canada 245 Consumers Road, Suite 400 Toronto, Ontario M2J 1R3

www.esemag.com

anada Canada

300

Emergency Valve Actuator Replaces Gas Scrubber • Gas Detector or Manual Activation Fire Code Approved for Toxic Gases • Fail-Safe Battery Operated System (877)-476-4222 www.halogenvalve.com September/October 2013 | 61


Stormwater Management

Geotubes successfully used for stormwater pond sediment dewatering By Mark Tymecki and Mark Simpson

E

fficient cleanout of stormwater management (SWM) ponds has been an ongoing challenge for many years. During construction and over time, properly functioning SWM ponds collect sediment from a designated catchment area. As they fill with sediment, efficiency diminishes and eventually they need to be cleaned out. With many ponds now approaching their first cleaning cycle,

this challenge is becoming even more prevalent. Evaluating the options The traditional approach to pond cleaning is to drain it, put it on bypass, then use heavy machinery to dig out, stockpile and haul away the sediment. This method works well in certain applications, particularly if dry weather is expected and the cleanout can be per-

The area is lined and graded slightly to a low point, allowing control of discharged water from the tubes.

The remote controlled hydraulic dredge pumps slurry into the Geotubes.

62 | September/October 2013

formed quickly. It is also widely understood and many contractors are well experienced with this approach. The Geotube® approach involves the use of a hydraulic dredge and large synthetic bags, commonly referred to as Geotubes, to collect and dewater the sediment. This method has not been widely used for Ontario SWM ponds, because the technology is relatively new and the flocculation process (polymer addition) is not widely understood. However, this is changing, as more successful applications are completed. The non-invasive nature of this approach is appealing for a number of reasons. In May 2013, the Geotube method was chosen for cleaning out three ponds in Vaughan, Ontario, for the following reasons: • No need to drain the pond, or take it off-line, while the cleaning process took place. • Extremely low impact to the surrounding naturalized area, due to the absence of construction vehicle traffic. • Minimized impact to the surrounding community and reduced carbon footprint, as the number of trucks required to haul dewatered and consolidated sediment was substantially reduced. • Minimal impact on the receiving downstream watercourse, since neither the flow volumes, nor turbidity levels from the pond, were affected during the cleanout. Implementation First, an appropriate lay down area was prepared to deploy the Geotubes. It was lined and graded slightly to a low point, so that water discharged from the tubes could be controlled and directed back into the pond. A remote controlled dredge with tow lines was then deployed into the pond. It was guided by a cable in a grid pattern to ensure no areas of the pond bottom were missed. The dredge pumped a slurry of sed-

Environmental Science & Engineering Magazine


Stormwater Management

Geotube being pumped with slurry from pond.

iment and water through a 6” diameter hose from the pond, through a polymer injection system and then into the Geotube where dewatering took place. The sediment volume in situ totalled approximately 3,100 m3, at between 9% and 22% solids. As expected, higher percentage solids content was found in the pond forebays. The Geotube continued to dewater the sediment after pumping was completed. Generally the longer it is allowed to sit, the more dewatering takes place.

Geotube after approximately one month of dewatering.

After approximately one month, the tubes are ready to be opened up and the sediment removed. Conclusion The pond cleanout was a success. The project delivery team was able to achieve the objectives of a fast, efficient, low impact pond cleanout within the allotted time and cost constraints. By early August, sediment in the tubes had completed its consolidation process. At this stage, the tubes were ready to be cut

open and the sediment removed. There is no one solution for SWM cleanout applications, due to their diverse nature. However, in this case, Geotube technology proved to be both cost-effective and environmentally sensitive. Mark Tymecki, C.E.T. and Mark Simpson, P.Eng. MBA, are with Layfield Environmental Systems Ltd. For more information, E-mail: tstarchuk@layfieldgroup.com

Waterra introduces the HydraSleeve — a new way to collect discrete interval samples. With no need to purge or dispose of purge water, this groundwater sampler reduces your costs by saving time. • COLLECT SAMPLES WITH NO DRAWDOWN & MINIMAL AGITATION • EASY TO USE – SIMPLY "POP & SQUEEZE" OPEN THE TOP, THEN ATTACH YOUR LINE & THE RE-USEABLE WEIGHT • NO FLUID MIXING FROM OTHER INTERVALS • NO PURGING NEEDED • A SINGLE HYDRASLEEVE CAN DELIVER SAMPLES OF 650 ML TO 2 LITRES FROM 2" MONITORING WELLS • HYDRASLEEVE PRODUCTS ARE ALSO AVAILABLE FOR 1" AND 4" MONITORING WELLS

HYDRASLEEVE www.waterra.com

(CANADA) Waterra Pumps Limited sales@waterra.com • tel: 905.238.5242 (USA) Waterra USA Inc. waterra@openaccess.org • tel: 360.738.3366

www.esemag.com

September/October 2013 | 63


Biosolids Management

London recognized for its new biosolids ash management system

T

he City of London, Ontario, operates six wastewater treatment plants. Sludge generated DW ¿YH RI WKHVH LV WUXFNHG WR the Greenway Pollution Control Plant where it is mixed in holding tanks with Greenway’s sludge. All of this sludge is WKHQ VHQW WR D ÀXLGL]HG EHG LQFLQHUDWRU For years, ash produced through the incineration process had been discharged to a two lagoon system where it was stored and then periodically transported off-site. While lagoons are used by many municipalities for the management of various waste streams, they do present their own set of challenges. Maintenance and general upkeep can be labour-intensive. Lagoons eventually become full and their contents must be disposed of. :LWK OLPLWHG RSWLRQV IRU ¿QDO GLVposal of the material and the high cost associated with removing ash and transporting it off-site, a solution was sought which would not only reduce the operational costs of managing ash, but also produce an end product which could be more easily disposed of. Bishop Water Technologies began working with the City of London in the spring of 2010, to develop a solution using the GeotubeŽ dewatering technology to manage the ash waste stream. Extensive on-site testing and trials were conducted to determine the optimum chemical for conditioning the material for dewatering with the Geotube technology. The City then requested a pilot project, to determine the effectiveness of the technology at dewatering and retaining the ash material on a larger scale. The solution In late 2010, Bishop Water began a pilot project using a Geotube unit measuring 30 ft. in circumference and 50 ft. long. The unit was situated around the perimeter of the existing lagoon cells. The ash slurry was diverted from the lagoon cells, discharging directly into the unit. Existing infrastructure was used to chemically condition the material. Fil-

64 | September/October 2013

Geotube units dewatering clear filtrate during the filling process.

trate produced through the dewatering process was discharged by gravity to the existing lagoon cells. Based on the success of the pilot project, the City of London determined WKDW *HRWXEH XQLWV ZRXOG RIIHU VLJQLÂżFDQW EHQHÂżWV ZKHQ FRPSDUHG WR PDQDJing the waste stream using the on-site lagoon cells. The City retained R.V. Anderson Associates as the lead engineering group for the project. Throughout 2011, Bishop Water worked closely with both R.V. Anderson and the City of London, to develop a methodology and design for the installation which would allow the Geotube units to operate as effectively as possible. Construction Construction of a permanent Geotube installation began in the fall of 2011. Concrete dewatering cells were constructed to accommodate the required units. Jersey barriers were used to segregate the cells, with each of the FHOOV VORSLQJ VOLJKWO\ WR D ÂżOWUDWH FROOHFtion basin. The dewatering cells were originally constructed to accommodate seven Geotube units measuring 75 ft. in circumference and 55 ft. long. However, to allow for increased capacity, the system has since started to use units 85

ft. in circumference and 55 ft. long. 7KH XQLWV XVHG LQFRUSRUDWH ÀDW HQG technology. This allows a higher capac-

How Geotube dewatering technology works Dewatering with Geotube technology is a three-step process. In the FRQÂżQHPHQW stage, the *HRWXEH FRQWDLQHU LV ÂżOOHG ZLWK dredged waste materials. The conWDLQHUÂśV XQLTXH IDEULF FRQÂżQHV WKH ÂżQH JUDLQV RI WKH PDWHULDO In the dewatering phase, excess water simply drains from the container. The decanted water is often of a quality that can be reused or returned for processing, or returned to native waterways without additional treatment. ,Q WKH ÂżQDO SKDVH consolidation, the solids continue to compress due to desiccation, as residual water vapour escapes through the fabric. Volume reduction can be as high as 90 per cent.

Environmental Science & Engineering Magazine


Biosolids Management ity than traditionally fabricated Geotube units, yet has the same footprint.

Volume reduction can be as high as 90 per cent.

Prior to the implementation of the Geotube units the raw ash slurry was discharged directly from the plant to onsite lagoons where it was stored and periodically transported offsite.

Performance The performance of Geotube units to date has not only met the expectations of the City of London, but exceeded them. The simplicity of the technology allows operators at the Greenway Pollution Control Plant, to monitor the installation and operate key components of the facility remotely. This means no additional personnel are required to operate the installation and minimal work hours are required by existing staff. Filtrate produced through the dewatering process is transferred to a lift station and then pumped back into the treatment process at the Greenway Plant for further treatment prior to discharge. The plant was designed to provide maximum on-site storage capacity. The City of London has arranged for the dewatered material to be used as an aggregate for concrete, NHHSLQJ LW RXW RI LWV ODQG¿OO 7KLV LV EHLQJ GRQH DW D IDU ORZHU cost than the previous practice of emptying the lagoons. As well as being considered a success by the City, the ash management system was awarded the 2012 Technical Innovation Award, by the Ontario Public Works Association, and the American Public Works Association Technical Innovation Award for 2013. For more information, E-mail: kevin@bishopwater.ca

When you’re ready to make a greater impact When you’re ready to go further in your career You are ready for American Public University American Public University is ready to help you move your career forward. We offer respected degrees in Environmental Science, Environmental Policy & Management, and more — completely online. And people are taking notice. We’ve been nationally recognized by the Sloan Consortium for effective practices in online education, and 99% of employers surveyed would hire one of our graduates again.*

When you’re ready, visit StudyatAPU.com/ese

*APUS Alumni Employer Survey, January 2011-December 2011 We want you to make an informed decision about the university that’s right for you. For more about our graduation rates,the median debt of students who completed each program, and other important information, visit www.apus.edu/disclosure.

www.esemag.com

September/October 2013 | 65


Monitoring

DO measurements affected by many factors By Patrick Higgins

T

KH PRVW VLJQL¿FDQW YDULDEOH for dissolved oxygen measurements is temperature, so it is important to ensure that any temperature sensor is measuring correctly. Due to the increase or decrease in molecular activity, diffusion of oxygen through the membrane of an electrochemical probe, or sensing element of an optical probe, changes with temperature. The change in diffusion rate based on temperature can be up to approximately 4% per degree Celsius for steady-state electrochemical sensors, depending on the membrane material, and 1% per degree Celsius for rapid pulse sensors. It is approximately 1.5% per degree Celsius for optical sensors. For example, if the temperature of a sample changes from 20°C to 15°C, the probe signal would decrease by varying rates depending on the sensor in use. This gives a lower DO per cent saturation reading even though the per cent saturation of the water has not changed. Therefore, the sensor signal must be compensated for changes in temperature. This is done by adding a thermistor to the circuit of older, analog instruments. For newer, digital instruments, the software compensates for temperature changes with proprietary algorithms, which use temperature readings from the probe’s thermistor. Temperature and oxygen solubility in water The above adjustment only compensates for temperature’s effect on the oxygen diffusion rate through a membrane or sensing element. In addition to this, temperature also affects the ability of water to dissolve oxygen. The solubility of oxygen in water is directly proportional to temperature (see Table 1). Warmer water cannot dissolve as much oxygen as colder water. For example, in an oxygen saturated sample of water at sea level (exposed to 760 mmHg of barometric pressure), the per cent saturation value will be 100% regardless of the temperature because it is fully saturated.

66 | September/October 2013

Table 1.

However, th H the dissolved di l d oxygen mg/L /L concentration will change with temperature because the solubility of oxygen in water changes with it. For instance, at 15ºC water can dissolve 10.08 mg/L, while at 30ºC water can only dissolve 7.56 mg/L of oxygen even though the per cent saturation value is 100% in both samples. Therefore, we must compensate the mg/L concentration reading, as per the temperature of the sample. Both of these temperature effects are factored into the conversion of the probe signal to a mg/L concentration. For newer, digital instruments, the software compensates for both of these temperature-related factors, after instrument calibration and during readings. The temperature compensation for the per cent saturation reading is em-

pirically i i ll dderived, i d while hil th the conversion i from per cent saturation, temperature and salinity to a mg/L concentration is automatically carried out by the instruPHQW¶V ¿UPZDUH )RUPXODH DYDLODEOH LQ Standard Methods for the Examination of Water and Wastewater are used. Determining DO mg/L from per cent saturation The following explains how to convert per cent saturation to mg/L (also referred to as ppm): Step one: Determine the per cent saturation, temperature, and salinity of the sample. (Let’s assume a sample is measured to have: 80% DO saturation 0 ppt salinity at 20ºC.) Step two: Multiply the per cent saturation reading by the value in appro-

Environmental Science & Engineering Magazine


Monitoring priate column (depends on salinity) and row (depends on temperature) based on the Oxygen Solubility Table. (Using Step One assumption: Multiply .80 (which is the DO per cent) by 9.09 (value from oxygen solubility table at 0 salinity and 20ÂşC) = 7.27 mg/L. Result: Using the above sample, 7.27 is the mg/L value that corresponds to an 80% DO saturation reading of a sample with zero salinity at 20ÂşC. Salinity- the second variable The second variable that affects DO concentration is the salinity of the water sample. While the per cent saturation reading is not a function of the salinity (or dissolved solids content) of the water, the mg/L concentration changes VLJQLÂżFDQWO\ ZLWK VDOLQLW\ $V WKH VDOLQity of water increases, its ability to dissolve oxygen decreases. For example, oxygen saturated freshwater with 0 ppt salinity at 25ÂşC contains 8.26 mg/L of oxygen, while oxygen saturated sea water (~36 ppt) at the same pressure and temperature contains only 6.72 mg/L of dissolved oxygen. Thus, salinity (along with temperature)

must be factored into the instrument’s calculation of mg/L. This calculation is based on the per cent saturation reading, temperature reading, and the measured or entered salinity value, using formulae found in Standard Methods for the Examination of Water and Wastewater. Correcting for salinity The salinity value used by the instrument in the calculation of mg/L is obtained one of two ways, depending on the instrument being used. For dissolved oxygen instruments that also measure conductivity, the salinity value measured by the conductivity sensor is used for the mg/L calculation. Therefore, it is important to ensure the conductivity sensor is calibrated and reading accurately in order to obtain accurate DO mg/L readings. For dissolved oxygen instruments that do not have a conductivity sensor, the salinity value of the sample must be manually entered by the end user. When sampling water of varying salinity, for example in brackish waters such as estuaries or coastal wetlands, it is recommended that you use

a dissolved oxygen instrument that also measures conductivity for highest data DFFXUDF\ $ GLVVROYHG R[\JHQ LQVWUXment that also has a conductivity sensor will use the real-time salinity readings from the conductivity sensor for every mg/L calculation. This will make sampling easier, since it will not be necessary to manually change the correction factor at each new sampling site. It’s important to keep in mind, when calibrating a DO meter, if you have to manually input the salinity value, to input the value of the water you will be measuring. If you have a conductivity sensor in conjunction with the DO sensor, make sure the conductivity is calibrated properly in order to compensate for the correct salinity value. Barometric pressure – the third variable Barometric pressure affects the pressure of oxygen in a sample of air or water. For example, the percentage of oxygen in air is always 21%, but the actual pressure of oxygen varies with changes LQ EDURPHWULF SUHVVXUH $W VHD OHYHO WKH continued overleaf...

MUNICIPAL • INDUSTRIAL WATER • WASTEWATER • BIOENERGY

www.greatario.com 519-469-8169 sales@greatario.com www.esemag.com

September/October 2013 | 67


Monitoring pressure of oxygen is 160 mmHg (.21 x 760 mmHg). In a fully aerated sample, under these conditions, the per cent saturation measured by a sensor would be 100% (160/160 x 100%). If the temperature of the sample is 25ºC, the instrument would calculate the dissolved oxygen concentration as 8.26 mg/L. As the sample is moved up in altitude and kept air-saturated, the barometric pressure would decrease and so would the pressure of oxygen in the sample. At 1126 ft of elevation, the pressure of oxygen would be 153 mmHg (.21 x 730 mmHg) and the per cent saturation relative to sea level read by the probe would be 95.6% (153/160 x 100%) in the fully aerated sample. If the temperature of the sample is 25ºC, the instrument would calculate a dissolved oxygen concentration of 7.92 mg/L or 96% of 8.26 based on YSI’s Oxygen Solubility Table. The effect of barometric pressure is overcome by proper sensor calibration. Barometric pressure is used in the majority of dissolved oxygen sensor calibrations as described in the Calibration section of The Dissolved Oxygen Handbook, since it determines the absolute pressure of oxygen in a sample of air or water at the time of calibration and it is this pressure which is measured by all oxygen sensors. When calibrating oxygen sensors, the sensor’s output is set to this known

68 | September/October 2013

pressure off oxygen. If the th sensor outt put changes after calibration, then the instrument would calculate a per cent saturation based on a simple linear regression calculation. Thus, as long as the system does not drift, the sensor’s output can always be XVHG WR GH¿QH WKH R[\JHQ SUHVVXUH LQ any medium after performing a proper calibration, and the use of the barometric pressure (or altitude) at the time of calibration is the key factor in setWLQJ WKH SURSHU FDOLEUDWLRQ FRHI¿FLHQW Therefore, it is not necessary to correct for changes in barometric pressure by recalibrating after performing a proper initial calibration in order to obtain acFXUDWH UHDGLQJV LQ WKH ¿HOG Flow dependence – the fourth variable Steady-state electrochemical sensors (polarographic and galvanic) consume oxygen during measurement and therefore require sample movement or the UHDGLQJV ZLOO EH DUWL¿FLDOO\ ORZ 7KLV LV FRPPRQO\ UHIHUUHG WR DV ÀRZ GHSHQGHQFH VLQFH WKH VHQVRU LV GHSHQGHQW RQ ÀRZ RU

water t movementt across th the membrane b iin order to obtain accurate readings. Optical sensors, however, use a non-consumptive method for dissolved oxygen measurements, resulting in a VHQVLQJ PHWKRG ZLWK ]HUR ÀRZ GHSHQdence or stirring requirement. However, VWXGLHV KDYH FRQ¿UPHG UHVSRQVH WLPHV on optical sensors can be improved with ÀRZ $FFXUDF\ GRHVQœW FKDQJH MXVW WKH amount of time to get to a reading. This may be an advantage when measuring many BODs. For steady-state electrochemical sensors, the membrane material and thickness dictates the degree of the sensor’s ÀRZ GHSHQGHQFH )RU H[DPSOH SRO\HWKylene membranes, frequently notated as 3( UHTXLUH OHVV PRYHPHQW RU ÀRZ WKHQ WUDGLWLRQDO SRO\WHWUDÀXRURHWK\OHQH 7KH stirring dependence of each sensor and membrane type, along with the recommended stirring rates, is listed in YSI’s Membrane Comparison Guide. Patrick Higgins is with YSI, a Xylem brand. For more information, E-mail: cosentino.f@spdsales.com

Environmental Science & Engineering Magazine


Instrumentation

Immediate pH correction for fluctuating flows offers many benefits

I

n a number of water, wastewater and industrial process applications, pH is one of the most critical and highly sensitive analytical measurements. In wastewater treatment, pH can be measured online in the aeration basins to control the acidic or alkaline condition of the mixed liquor, in order to provide optimum conditions for microorganism activity. Drinking water plants also need accurate and reliable pH control systems at the supply inlet, to determine the appropriate treatment for incoming water. They also need to ensure proper pH of the treated water before it enters the public water supply. Most instrumentation sensors offer relatively constant performance and response time. However, being based on an electrochemical measurement, this is

not always the case for a pH electrode. There are many process factors which can influence their response rate and accuracy. There are three common methods to determine pH: 1. Visual method using litmus paper. 2. Photometric method which uses a spectrophotometer to measure the wavelength. 3. Potentiometric method which is an electro-chemical measurement of the EMF created by a chemical reaction. The only one, which can be used in process control for continuous in-line measurement, is the potentiometric method. However, there are many factors which can cause a delay in accurate measurement. The response time can vary based on the thickness and composition of the probe gel layer, diaphragm porosity, reference contamination, age

By Sadiq Khan

of probe, glass membrane integrity, and the length of the signal cable. To achieve the nominal tolerance of 0.01 pH units, a response time of 30 seconds is needed. This delay in response time can have a negative impact on any of the pH critical processes, especially reverse osmosis systems and biological treatment. For example, a delay in pH response can easily result in the fouling of an RO membrane due to the incorrect dosing of caustic, or halt the bacteria activity of microorganisms in a biological process. An overdose of caustic into the process stream (if the flow rate were to drop and not be compensated for) could cause the water’s pH to drop below the specified range for the RO membranes. This is of particular concern when the concentrate (reject waste) is being recycontinued overleaf...

Worldwide Engineers with a Passion for Solutions All Engineers are qualified professionals but the best solutions come from a team of: UÊ Ì iÊÃi>à i`Ê> `ÊiÝ«iÀ i Vi` UÊ ÊÌ iÊ Ü i`}i>L iÊ> `Ê proficient UÊ Ì iÊvÀià Ê> `Êi Ì Õà >ÃÌ V

Õi «À Ìi`ÊÌ ÊÞ ÕÀÊiÝ>VÌÊ specification, our team provides customized, environmental and sustainable engineering solutions for your unique objectives.

HEAD OFFICE

70 Valleywood Drive, Markham, ON CANADA L3R 4T5 T. 905.940.6161 | 416.987.6161 www.ColeEngineering.ca

www.esemag.com

September/October 2013 | 69


Instrumentation

Save the Date! August 17-20, 2014 Metro Toronto Convention Centre, Toronto, Ontario

www.apwa.net/congress 70 | September/October 2013

cled into the feed stream to improve overall efficiency. In this case, the flow rate will be fluctuating and the pH will be decreasing, due to the formation of carbonic acid. An ideal solution would be to correct the pH immediately based on flow. A program has been implemented in Burkert Fluid Control’s type 8619 multiCELL multifunction transmitter/controller to do just this. It is done using multiple logic blocks to allow for a great deal of flexibility. In an inline pH control system, it is essential to confirm the measurement line has the minimum flow The 8619 multiCELL multivelocity. This is because function transmitter/controlthe chemical injection nozler. zle may be any distance away from the analytical measurement point. If the flow becomes static, the pump will continue to dose until the pH adjusted process fluid reaches the measuring point. This will result in a drastic overshoot beyond the set-point pH levels. The multiCELL program uses a “System Switch” logic block, which can be used to override the program if there is no flow detected. The override, in this case, would be to keep the pump turned off, even if the pH set-point is not achieved. When trying to adjust a pH dosing pump based on attenuating flow, a ratio flow control loop can be used. This will need to be combined with a PID (proportional-integral-derivative) loop, using pH as the process value. When the two outputs are combined using only a scaled value of fifty present on each, the result will be the desired full range. This has been done in the multiCELL using the “PROP”, “On/Off”, “PID”, and arithmetic “A+B” function blocks. This method is effective for dosing chemicals in a safe and effective manner to protect RO membranes from damage. It also increases efficiency and cost control, by minimizing excess dosing of flocculants and neutralization chemicals. With the sheer range of pH applications throughout all water and wastewater treatments and the criticality of each of these measurements on the process as a whole, it is definitely worth taking the time to implement a well-thought-out pH control system. Carefully considering the layout of injection points, pH measurement points and the potential need for integrated flow compensation between the two, will lead to a more responsive pH loop, a more efficient chemical dosing scheme and better overall process control. Sadiq Khan is with Burkert Fluid Control Systems. E-mail: sadiq.khan@burkert.com Environmental Science & Engineering Magazine


American Public University is a leading provider of quality online education. APU offers more than 180 undergraduate and graduate degree and certificate programs for environmental science, policy, and management professionals. When you’re ready to learn more, visit StudyatAPU.com/ESE. Tel: 877-777-9081 E-mail: info@apus.edu Web: StudyatAPU.com/ESE American Public University

Biosolids management

Small double wall tanks

American Water provides beneficial reuse of biosolids; advanced technologies - Class A biosolids; mobile dewatering; digester, reactor, tank and lagoon cleaning; confined space entry; treatment plant by-pass; vacuum and haulage services; custom, mobile screening; and free assessments and quotations. Tel: 800-846-2097 E-mail: terratecsales@amwater.com Web: www.terratec.amwater.com

Small double wall tanks, from 20 to 405 gallons, provide primary and secondary containment for hazardous and corrosive chemicals in one unit. Linear polyethylene tanks are certified to NSF/ANSI Standard 61, and high-density crosslink resin tanks for chemical storage. ISO 9001:2008 Certified. Web: www.assmann-usa.com

American Water

Assmann Corporation of America

Submerged fixed film

Denso Petrolatum Tapes

%UHQWZRRGœV VXEPHUJHG ¿[HG ¿OP technology, AccuFAS, provides biological treatment for your siteVSHFL¿F SURFHVV JRDOV ,WV LQQRYDWLYH combination of distribution and vertical ÀRZ PHGLD eliminates shortcircuiting and SURYLGHV HYHQ ÀRZ DQG DLU GLVWULEXWLRQ for optimum contact between the waste stream and biomass. Tel: 610-374-5109 E-mail: waterinfo@ brentwoodindustries.com Web: www.brentwoodindustries.com

Proven worldwide for well over 100 years, Denso Petrolatum Tapes offer the best, most economical, long-term corrosion protection for all above and below ground metal surfaces. Requiring only minimum surface preparation and environmentally responsible, Denso Petrolatum Tape is the solution to your corrosion problems in any corrosive environment. For applications in mines, mills, refineries, steel mills, pulp & paper, oil & gas, and the waterworks industry. The answer is Denso! 7HO )D[ E-mail: blair@densona-ca.com Web: www.densona.com Denso

Brentwood Industries

Combination pH/ORP electrodes The new combined pH/ORP electrodes, Memosens CPS16D, CPS76D and CPS96D from Endress+Hauser, now make customers’ processes even more transparent. Two parameters measured at the same time or DOWHUQDWHO\ S+ SOXV H[WUD VHQVRU FKHFN - don’t leave room for interpretation. $QG IRU WKH ¿UVW WLPH RQH VLQJOH VHQVRU is able to deliver the rH-value! E-mail: info@ca.endress.com Web: www.ca.endress.com/memosens

Endress+Hauser Canada

CSF-34 sampler

Vertical screening system

Reciprocating rake screening system

Samplers have changed. The Endress +Hauser CSF34 is the new benchmark, with a choice of vacuum or peristaltic pumping and up to 24 simultaneous sampling routines. Add up to four industrial digital sensors with data logging and connect to SCADA with the latest communication protocols including Ethernet. The new CSF-34 is a complete monitoring and collection solution. E-mail: info@ca.endress.com Web: www.ca.endress.com

The new Vertical Auger MonsterŽ 6FUHHQ ¿WV inside pump stations. Wastewater pump stations are facing DQ LQÀX[ RI VHZHU FORJJLQJ ÀXVKDEOH wipes, so JWCE engineers developed the Auger Monster – AGV which conveys wipes straight up and out of the sewer system. 7HO )D[ E-mail: sales@envirocan.ca Web: www.envirocan.ca

JWC Environmental has introduced the new Bar Screen Monster™, using H[FOXVLYH technology WR FDSWXUH PRUH GHEULV 7KH ¿UVW VHOI contained reciprocating rake screening system is designed to capture and transport large amounts of wastewater debris to the discharge point. 7HO )D[ E-mail: sales@envirocan.ca Web: www.envirocan.ca

Endress+Hauser Canada

Envirocan

Envirocan

www.esemag.com

Product & Service Showcase

Online education

September/October 2013 | 71


Flow monitor FlowSiren, a wireless, low power, multisensor open FKDQQHO ÀRZ monitor with vision sensor, allows you to PHDVXUH DQG YLHZ DQ\ ÀRZ FRQGLWLRQV using contact and non-contact sensors. Advanced power management keeps the FlowSiren alive for over a year, uploading hourly data to your server location. Tel: 514-354-2511 E-mail: info@geneq.com Web: www.geneq.com

Product & Service Showcase

Geneq

Process mixing system The HYDRAULIX mixing systems feature a unique double nozzle design which allows for even energy distribution. This process optimizes solids suspension and contact to promote efficiency in a wide range of wastewater and bio-fuels applications. E-mail: sales@greatario.com Web: www.greatario. com

Greatario Engineered Storage Systems

New area-velocity flow meter

With the AVFM 5.0 Area-Velocity Flow Meter you FDQ PRQLWRU ÀRZ through open channels, partially full sewer pipes DQG VXUFKDUJHG SLSHV ZLWKRXW D ÀXPH RU ZHLU 7KLV QHZ ÀRZ PHWHU LV GHVLJQHG for municipal stormwater, combined HIÀXHQW UDZ VHZDJH DQG LUULJDWLRQ water. Tel: 888-473-9546 E-mail: info@greyline.com Web: www.greyline.com/avfm50.htm Greyline Instruments

H2FLOW SBR

Toxic gas multi-actuator valve controller

Single channel fluorometer

The H2FLOW SBR consists of FLUIDYNE Sequencing Batch Reactor internals integrated into a glass-fusedto-steel tank. It features jet aeration headers that never require replacement, and a solidsH[FOXGLQJ ¿[HG GHFDQWHU ZKLFK KDV been proven in many installations. Tel: 905-660-9775 :HE ZZZ K ÀRZ FRP

The Hexacon Model III Gas Shutoff System has a New OLED information display and the optional programmable relay interface module provides clear, timely, informational outputs. The microprocessor system measures and applies a torque of 30 foot-pounds or 50 foot-pounds for test or emergency valve closures for cylinder and ton container valves. Tel: 877-476-4222, Fax 949-261-5033 Web: www.halogenvalve.com Halogen Valve Systems

Turner Designs’ Enviro-T™ is an accurate, single channel ÀXRURPHWHU ZKLFK installs into a plumbing tee for direct in-line measurements. It is easily integrated with data collection systems, and provides a 4 - 20 mA signal output proportional to the relative concentration of WKH ÀXRURSKRUH RI LQWHUHVW LQ WKH VDPSOH water. It offers a wide dynamic range, low sensitivity, a compact package and easy integration with controllers. Tel: 604-872-7894, Fax: 604-872-0281 E-mail: salesv@hoskin.ca Web: www.hoskin.ca

H2Flow Equipment

Hoskin Scientific

Water quality monitoring

Inclined screw press

Protecting sensitive watershed

The YSI EXO Advanced Water Quality Multi-Parameter Monitoring Platform features wireless bluetooth communication, smart sensors, wet-mateable sensor/cable connectors, built in GPS, and extended battery life (90 days). New parameters include fDOM and total algae. Tel: 604-872-7894, Fax: 604-872-0281 E-mail: salesv@hoskin.ca Web: www.hoskin.ca

Huber Technology’s RoS3Q Inclined Screw Press dewaters sludge to provide impressive cake solids. The slow rotating auger handles the toughest of sludge. The RoS3Q runs unattended using fully automatic operation. Cost of ownership is very low. Tel: 704-990-2055 E-mail: marketing@hhusa.net Web: www.huberforum.net/ros3q

Strescon Limited in Saint John, New Brunswick, has supplied the largest Stormceptor ever installed in Atlantic Canada, an STC 14,000 installed at the Costco Wholesale site in Fredericton. The site encompasses Corbett Brook and adjacent wetlands on the grounds of the University of New Brunswick, which are home to various species, a mature forest and wetlands. Tel: 800-565-4801 E-mail: info@imbriumsystems.com Web: www.imbriumsystems.com; www.stormceptor.com

Hoskin Scientific

Huber Technology

Imbrium Systems

72 | September/October 2013

Environmental Science & Engineering Magazine


Double containment

Leak detection system

Utilizing 150 plus years of combined experience selling, designing, manufacturing, installing and servicing onsite hypochlorite generation equipment, the team at PSI have, with MicrOclor, implemented innovations to ensure equipment reliDELOLW\ PDWFKHV WKH RSHUDWLRQDO EHQHÂżWV of switching to an Onsite Hypochlorite Generation system. Contact Indachem IRU D FRVW EHQHÂżW DQDO\VLV Tel: 416-743-3751 Web: www.indachem.com

ClearGuardTM is a fail-safe, pressurerated clear containment piping system allowing for easy visual detection of leaks and minimizing risk for transport of aggressive chemicals in buildings. Clear-Guard Double Containment utilizes IPEX’s patented Centra-LokTM ÂżWWLQJ GHVLJQ ZKLFK NHHSV WKH FDUULHU pipe perfectly centered inside the containment pipe. Fittings are available in clear or “cost savingâ€? opaque. Tel: 866-473-9462 Web: www.ipexinc.com

IPEX double containment systems can be equipped with a patented Centra-Guard™ point-of-collection leak detection system. Centra-Guard systems are available for aboveground, suspended piping applications, with sensors housed in saddle-type clamps, as well as for below-grade piping systems, with sensors located in drip leg assemblies. Tel: 866-473-9462 Web: www.ipexinc.com

Indachem

IPEX

IPEX

Thermal drying

Through thermal sludge drying, Innodry 2E can be used to reduce the volume and improve the quality of wastewater biosolids. Innodry 2E’s innovative and patented combination of proven technologies allows the advantages of both direct and indirect dryers. Tel: 804-756-7600 Web: www.degremont-technologies.com Infilco Degremont

Electronic metering pumps

EMEC metering pumps provide quality, accuracy and a number of design innovations including: industryleading 5 year warranty on their solid construction PTFE diaphragm; master/ slave integration; integrated automatic re-priming system; integral pH and Redox pumps with direct probe input. KGO Group Ltd. is the Canadian distributor. Tel: 905-847-1544 E-mail: info@kgogroup.com KGO Group

www.esemag.com

Sludge dewatering

Dry polymer systems

The Dehydris™ Twist is an advanced sludge dewatering process from Degremont, employing the Bucher Unipektin hydraulic piston press technology. Up to 30% reduction in sludge bulk volume can be achieved over conventional dewatering and digested sludge can be dewatered to autothermal conditions before incineration. Tel: 804-756-7600 Web: www.degremont-technologies.com

KGO Group builds safety and quality into each of its dry polymer systems. Unique features include: SS construction, plug and dust-free wetting devices, standard knife-gate isolation valve, welded or quick connect ÂżWWLQJV ORZ SRO\PHU KRSSHU LQGLFDWLRQ DQG &6$ FHUWLÂżHG components. Tel: 905-847-1544 E-mail: info@kgogroup.com

Infilco Degremont

KGO Group

Interpreter register Master Meter’s Interpreter Register System, based on proven DialogŽ 3G technology, is a universal AMR upgrade that replaces the existing register on almost any brand of meter in minutes, without service interruption. It delivers AMR technology without wires or connections. Tel: 514-795-1535 E-mail: clauret@mastermeter.com Web: www.mastermeter.com Master Meter

Product & Service Showcase

Next generation OSHG equipment

Ultrasonic meter

OctaveÂŽ offers the latest in ultrasonic metering technology and is an excellent alternative to mechanical compound, single-jet, and turbine meters with no moving parts. Octave excels at maintaining sustained accuracy for the life of the meter while providing smart AMR capabilities. Tel: 514-795-1535 E-mail: clauret@mastermeter.com Web: www.mastermeter.com Master Meter

September/October 2013 | 73


Access hatches MSU MG Safety Hatches are the “open and shut caseâ€? for access hatches. They are manufactured to CSA standards right here in Canada by Canadian :HOGLQJ %XUHDX FHUWLÂżHG ZHOGHUV Web: www.msumississauga.com

MSU Mississauga

Product & Service Showcase

Portable gas chromatograph

The NETZSCH TORNADOÂŽ positive displacement, self priming, valveless pumps, offer high performance and are selected and configured for the requirements of each application. They are designed for intermittent or continuous operation, provide gentle pumping of the pumped product and are ideally suited for transfer, process and dosing applications. There are highly abrasion resistant and replaceable protection plates on both faces of the housing. Tel: 705-797-8426, Fax: 705-797-8427 E-mail: info@netzsch.com Web: www.netzsch.com

Noble is one of Ontario’s largest suppliers of pipe, valves, fittings and accessories for the wastewater and water treatment industries. The Noble Advantage: • 40 branches in Ontario • 200 delivery trucks • 500,000 sq. ft. distribution centre • Pipe cutting & grooving services Tel: 800-529-9805 Web: www.noble.ca

NETZSCH Canada

Noble

Flow meter

Diaphragm metering pumps

The Frog-4000 is a Hand-Held Portable Gas Chromatograph for detection of benzene, toluene, ethylbenzene, BTEX and other VOCs in water, air, and soil. It performs analysis in the ÂżHOG LQ PLQXWHV UHTXLUHV OLWWOH WHFKQLFDO H[SHUWLVH LGHQWLÂżHV WKH DFWXDO FRPpounds, and delivers sensitive results to allow instant decisions. Tel: 800-560-4402 E-mail: VDOHV#RVSUH\VFLHQWLÂżF FRP Web: ZZZ RVSUH\VFLHQWLÂżF FRP

The Sigma Series of diaphragm metering pumps from ProMinent has many new advanced features. With a removable/ externally mountable HMI (Human Machine Interface), variable metering SURÂżOHV GLDSKUDJP UXSWXUH ZDUQLQJ system, and cost savings through energy consumption based on power required, Sigma provides more safety and reliability for optimum metering results. Tel: 888-709-9933, Fax: 519-836-5226 E-mail: sales@prominent.ca Web: www.prominent.ca

Osprey Scientific

ProMinent Fluid Controls

Electronic motor

Grit removal system

The DRC electronic motor gives great ÀH[LELOLW\ in mounting a gear unit as it can EH PRXQWHG GLUHFWO\ YLD ÀDQJH DQG pinion shaft end. A completely new mechatronic drive system is created, WRJHWKHU ZLWK D KLJKO\ HI¿FLHQW KHOLFDO bevel, helical or parallel-shaft helical gear unit. Tel: 905-791-1553 E-mail: marketing@sew-eurodrive.ca Web: www.sew-eurodrive.ca

PISTAŽWorks™ is a packaged all in one headworks and grit removal scheme, offering a compact footprint and speedy/ efficient installation. The system features a fully automated control system, an integrated screening system for solids retention, a PISTAŽ Grit Concentrator, a PISTAŽ TURBO™ Grit Washer and a PISTAŽ 360™ Grit Chamber. Tel: 913-888-5201, Fax: 913-888-2173 E-mail: answers@smithandloveless.com Web: www.smithandloveless.com

SEW-Eurodrive

Smith & Loveless

74 | September/October 2013

Equipment supplier

Rotary lobe pump

DulcoFlowÂŽ flow meter is based on the ultrasonic measurement method. Operation without moving parts guarantees a long service life and wear-free operation. Its measurement range is between 0.1 and 50 litres per hour. A unique feature is that, for the first time, pulsed flow and the amount of liquid which has been dispensed by each pump stroke can be reliably and precisely measured and monitored. Tel: 888-709-9933, Fax: 519-836-5226 E-mail: sales@prominent.ca Web: www.prominent.ca ProMinent Fluid Controls

Enhance bioremediation

The Waterloo Emitter™ is a simple, lowcost device designed for the remediation of contaminated groundwater. It enables oxygen or other amendments to diffuse through silicone or LDPE tubing in a controlled uniform manner, enhancing DHURELF ELRUHPHGLDWLRQ ,W ¿WV 150 mm diameter wells. Tel: 905-873-2255, Fax: 905-873-1992 E-mail: instruments@solinst.com Web: www.solinst.com Solinst

Environmental Science & Engineering Magazine


New and Improved Hydrolift

Veolia has a wide range of solutions for biosolids processing and management. Our extensive portfolio of in-house technologies ranges from thermal (dryers, incinerators, thermal hydrolyzers) to biological processes (anaerobic (co) digestors, ammonia removal, etc.). We deliver sustainable systems tailored to customers’ need as solution, turn-key or DBO projects. Tel: 905-286-4846 E-mail: salescanada@veoliawater.com Web: veoliawaterstna.com

The portable, electrically operated Hydrolift has been one of the most popular mechanical actuators for the Waterra Inertial Pump, and we’ve been working to make it better. Today, the improved Hydrolift is more durable and easier to use and most importantly, more affordable than ever. Tel: 905-238-5242, Fax: 905-238-5704 E-mail: sales@waterra.com Web: www.waterra.com

Veolia Water Solutions & Technologies Canada

Waterra Pumps

Waterra Pumps

The Waterra Inertial Pumping System is the most widely used pump for monitoring wells in Canada. For developing, purging and sampling — nothing else comes close. Tel: 905-238-5242, Fax: 905-238-5704 E-mail: sales@waterra.com Web: www.waterra.com Waterra Pumps

EcoPlug Wellcaps

Trickling filters

The EcoPlug™ offers the latest in well plug design and is the only well cap made from recycled materials. If you’re looking for a durable, tamper-proof well cap that will withstand repeated use (and abuse) over many years, the EcoPlug is an excellent fit for your requirements. This well cap is available for 3/4”, 1”, 2” and 4” monitoring wells. Tel: 905-238-5242, Fax: 905-238-5704 E-mail: sales@waterra.com Web: www.waterra.com Waterra Pumps

Waterloo Biofilters® are efficient, modular trickling filters for residential and communal sewage wastewaters, and landfill leachate. Patented, lightweight, synthetic filter media optimize physical properties for microbial attachment and water retention. The self-contained modular design for communal use is now available in 20,000L/d and 40,000L/d ISO shipping container units - ready to plug in on-site. Tel: 519-856-0757, Fax: 519-856-0759 E-mail: wbs@waterloo-biofilter.com Web: www.waterloo-biofilter.com Waterloo Biofilter

PVC or Polyethylene

The Waterra Clear PVC EcoBailer and Weighted Polyethylene EcoBailer are both eco-friendly products. A better weight distribution allows these bailers to sink straighter, and the efficient valve design makes them the fastest sinking bailers available. Tel: 905-238-5242, Fax: 905-238-5704 E-mail: sales@waterra.com Web: www.waterra.com

Inertial pumping system

Amalgam UV lamps

Repair mortar

WEDECO Ozone Generators from Xylem eliminate pollutants, coloured substances, odours and micro-organisms without creating harmful byproducts. They are compact in design to reduce overall footprint, and provide reduced energy consumption per unit of ozone production. Tel: 514-695-0100, Fax: 514-697-0602 Web: www.xylemwatersolutions.com/ca

Xylem’s WEDECO ECORAY® ultraviolet lamps offer significant savings in operation and life cycle costs. The UV lamps incorporate a new long-life coating and improved overall stability and performance. An innovative gas and amalgam mixture in the lamp utilizes up to 80 percent less mercury. Corresponding electronic ballast cards have been fine-tuned to the specific requirements of ECORAY lamp aging characteristics. Tel: 514-695-0100, Fax: 514-697-0602 Web: www.xylemwatersolutions.com/ca

Megamix II thick repair mortar for resurfacing deteriorated concrete manholes, sewer pipe and water tanks is formulated for superior bond, chemical durability and high strength. It can be sprayed or trowel applied up to a thickness of 2 inches. It is NSF 61 approved. Tel: 604-273-5265 Web: www.xypex.com

Xylem

Xylem

XYPEX Chemical Corporation

Chemical-free water treatment

www.esemag.com

Product & Service Showcase

Biosolids and bioenergy

September/October 2013 | 75


ES&E NEWS New satellite maps track algal blooms in Great Lakes Acoustic Panels, Enclosures & Products WE WELCOME YOUR INQUIRIES

Email: info@acousticproductsales.com Web: www.acousticproductsales.com Tel: (613) 551-6100

Five decades of excellence in infrastructure ™•Š——’—Â?ȹǭȸŽ—Â?’—ŽŽ›’—Â?

• ANTHRACITE • QUALITY FILTER SAND & GRAVEL • CARBON • GARNET ILMENITE • REMOVAL & INSTALLATION 20 Sharp Road, Brantford, Ontario N3T 5L8 • Tel: (519) 751-1080 • Fax: (519) 751-0617 E-mail: swildey@anthrafilter.net • Web: www.anthrafilter.net

High Pressure Water Jetting Liquid/Dry Vacuum Services Dry Ice Cleaning Hydro Vac Excavating

www.aquablast.ca

Markham, Ontario 905-747-8506 WeKnowWater@BV.com Consulting • Engineering • Construction • Operation

76 | September/October 2013

www.bv.com

Scientists from the Michigan Tech Research Institute are using satellite data to generate maps of harmful algal blooms (HABs) in the Great Lakes. The maps show the location and extent of HABs, as well as areas of water quality and public health concern, in the Western Basin of Lake Erie, Saginaw Bay on Lake Huron and Green Bay on Lake Michigan. They are updated weekly and are available online at: www.mtrihabsmapping.org “These maps give unprecedented access to real-time data to inform stewardship decisions and promote sustainable ecosystem restoration and protection efforts,â€? said Robert Shuchman, co-director of MTRI and a lead scientist on the HABs satellite-mapping project. The data will be useful to commerFLDO VSRUW DQG FKDUWHU ÂżVKHUPHQ VDLORUV tourists and public water system managers, as well as beach managers. It is predicted that the general public will use it as well. “After all,â€? said Shuchman, “you don’t want your grandkids going to the beach and jumping into pea soup.â€? The work is presently funded by the US EPA Great Lakes Restoration Initiative. www.mtu.edu

First Nations water management funded The Natural Sciences and Engineering Research Council of Canada (NSERC) will provide $1.65 million over six years, to fund the H20 CREATE Program for Water and Sanitation Security in First Nations. Dr. Farenhorst at the University of Manitoba will lead the program, through the Collaborative Research and Training Experience (CREATE) initiative. Leading researchers from Trent University, the University of Manitoba, and the University College of the North, will establish an innovative and culturally respectful research training program that will provide a highly-trained labour force and an innovative system. This is urgently needed to address the Canadian water and sanitation crisis in First Nations communities. Environmental Science & Engineering Magazine


ES&E NEWS Potential employers may interact with trainees by providing work terms and student training workshops, as well as by serving as advisors on trainees’ research projects organizations.The H2O &5($7( SURJUDP LV WKH ¿UVW WUDLQLQJ program in Canada to combine technical water and wastewater management training with Indigenous theory, law and methodological skills training. www.trentu.ca

Specialists in a comprehensive range of Municipal, Environmental, Structural, Building, Water Resources, Transportation and Municipal Engineering Collingwood

Bracebridge

Orillia

Email: info@cctatham.com

Barrie

Web: www.cctatham.com

30+ Years of Water and Wastewater Solutions

Siemens marks 100 years of water treatment Siemens Water Technologies is marking a century of industry innovation and leadership with the 100-year anniverVDU\ RI WKH ÂżUVW FKORULQH JDV PHWHULQJ unit for water disinfection, a milestone EUHDNWKURXJK LQ WKH ÂżJKW DJDLQVW ZDWHUborne disease. 7KH ÂżUVW FRPPHUFLDOO\ SURGXFHG JDV chlorinator was installed in 1913 in a public drinking water system by Wallace & Tiernan, now a Siemens Water Technologies company. The technology revolutionized the way the world fought water-borne diseases which killed nearly 30,000 people per year in the 1900s in the United States alone. “The use of chlorine in water treatment has arguably done more to safeguard the health of the world than any other development,â€? said Dr. Lukas /RHIĂ€HU 6LHPHQV :DWHU 7HFKQRORJLHV CEO. “To this day, chlorination in general is still the most widely used disinfection method.â€? www.water.siemens.com

Wastewater Collection/Treatment Water Supply/Treatment/Storage/Distribution „ Environmental Site Assessment/Remediation „ Hydrogeological Investigations/Modelling „ Watershed/Stormwater Management „ Information Technology/Data Management „ „

3,000 Staff; 90+ Offices

1.800.265.6102 www.CRAworld.com

Worldwide Engineering, Environmental, Construction, and IT Services

35 YEARS DREDGING HIGH SPEED CENTRIFUGES HIGH VOLUME PUMPING-HDPE PIPE HDPE PIPELINE FUSING GEO TUBE DEWATERING Competent and Complete Services Lagoons, Digesters, Ponds, Lakes, Marinas, Waste Reduction, Municipal & Industrial

Tel: (506) 684-5821 | Fax (506) 684-1915 | www.girouxinc.com Ideal mixing for: Anoxic Basins Aeration Basins Large Bubble Mixing Technology Sludge Mixing Drinking water storage tank mixing Innovative, air burst driven mixing Sewage pump station grease cap busting & odor control Most energy-efficient mixing Industrial Applications No in-basin moving parts Food processing applications, liquor blending Easy installation & a wide range of mixing applications

HYDRO-PULSE

HYDRO-LOGIC ENVIRONMENTAL INC. 762 Upper St. James St., Suite 250, Hamilton, ON L9C 3A2 Ph: 905-777-9494 Fax: 905-777-8678 info@hydrologic.ca www.hydrologic.ca

Puralytics earns IWA’s Global Honour Award Puralytics’ SolarBag™ will receive the International Water Association’s (IWA) Global Honour Award for Drinking Water Supply, for its innovative solution to providing access to safe drinking water. The IWA will present the award in October in Nairobi, Kenya. It will jointly recognize Puralytics and Good Samaritan Ministries, for their combined work to implement and administer this successful drinking water project across peri-urban Malawi. The three-liter SolarBag is a reusable continued overleaf... www.esemag.com

AIR RELEASE/VACUUM BREAK VALVES FOR SEWAGE & WATER • “ANTI-SURGE /ANTI-SHOCKâ€? • 10-YEAR WARRANTY • ALL STAINLESS

HYDRO-LOGIC ENVIRONMENTAL INC. RGX

762 Upper St. James St., Suite 250, Hamilton, ON L9C 3A2 Ph: 905-777-9494 Fax: 905-777-8678 info@hydrologic.ca www.hydrologic.ca

RBX

RELIANT WQA WATER QUALITY AERATOR for Lagoons and Aquaculture

• Course & fine bubble aeration • Tames sludge buildup • Eliminates thermal stratification • Eliminates seasonal turnover

Coarse & ďŹ ne bubble aeration

• Only 4 hp Tames moves 9 MGD sludge buildup Eliminates thermal stratiďŹ cation • Handles up to 5 acres per unit Eliminates seasonal turnover 4 hp moves MGD • Efficient - Only Up to 15 lbs 9O2/hr Handles up to 5 acres per unit • Low maintenance EfďŹ cient: Up&toSimple! 15 lbs O /hr 2

Low maintenance & Simple!

HYDRO-LOGIC ENVIRONMENTAL INC. 762 Upper St. James St., Suite 250, Hamilton, ON L9C 3A2 Ph: 905-777-9494 Fax: 905-777-8678 info@hydrologic.ca www.hydrologic.ca

September/October 2013 | 77


ES&E NEWS Insitu Groundwater Contractors • • • • • P: 519-763-0700 F: 519-763-6684 • 150 Stevenson Street, South Guelph, ON N1E 5N7

Dewatering systems Mobile groundwater treatment systems Well and pump installation and maintenance Pump, filter, generator rentals Sediment tank rentals Insitu groundwater remediation systems

www.insitucontractors.com

INTERNATIONAL WATER SUPPLY LTD. WWW.IWS.CA

WELL AND PUMP MAINTENANCE Performance Testing, Inspections, Well Rehabilitation & Repairs Lineshaft and Submersible Turbines 342 Bayview Drive, Box 310, Barrie, Ontario, Canada L4M 4T5

Tel: (705) 733-0111, Fax: (705) 721-0138 E-Mail: iws@iws.ca

ZDWHU SXUL¿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¿OO WKH EDJ ZLWK ZDWHU DQG OHDYH LW H[SRVHG WR WKH VXQ IRU D IHZ KRXUV DOORZLQJ LW WR EH XVHG PXOWLSOH WLPHV SHU GD\ 7KH HPSW\ EDJ FDQ EH VWRUHG IRU XS WR VHYHQ \HDUV DQG FDQ EH UHXVHG KXQGUHGV RI WLPHV www.puralytics.com

Minister Aglukkaq visits Norway to tackle climate pollutants

10 Alden Road Markham, Ontario Canada L3R 2S1 Tel: 905-475-1545 Fax: 905-475-2021 www.napier-reid.com

Package Wastewater Treatment Plants/SBR/MBR/RBC/EA/DAF

10 Alden Road Markham, Ontario Canada L3R 2S1 Tel: 905-475-1545 Fax: 905-475-2021 www.napier-reid.com

Package Water Treatment Plants/Gravity/Pressure/Membrane/Ion Exchange/GAC

78 | September/October 2013

/HRQD $JOXNNDT 0LQLVWHU RI WKH (QYLURQPHQW 0LQLVWHU RI WKH &DQDGLDQ 1RUWKHUQ (FRQRPLF 'HYHORSPHQW $JHQF\ DQG 0LQLVWHU IRU WKH $UFWLF &RXQFLO WUDYHOOHG WR 2VOR 1RUZD\ LQ 6HSWHPEHU WR SDUWLFLSDWH LQ WKH KLJK OHYHO DVVHPEO\ RI WKH &OLPDWH DQG &OHDQ $LU &RDOLWLRQ &&$& WR 5HGXFH 6KRUW /LYHG &OLPDWH 3ROOXWDQWV ³$V DQ $UFWLF QDWLRQ &DQDGD SURIRXQGO\ XQGHUVWDQGV WKH FOLPDWH DQG SXEOLF KHDOWK EHQH¿WV RI UHGXFLQJ VKRUW OLYHG FOLPDWH SROOXWDQWV VXFK DV EODFN FDUERQ DQG PHWKDQH ´ VDLG 0LQLVWHU $JOXNNDT ZKR LV FKDLU RI WKH $UFWLF &RXQFLO &DQDGD¶V 1RUWK LV HVSHFLDOO\ VHQVLWLYH WR WKH HIIHFWV RI EODFN FDUERQ DV WKHUH LV DQ DGGLWLRQDO ZDUPLQJ HIIHFW ZKHQ GHSRVLWHG RQWR VQRZ DQG LFH &DQDGD LV D IRXQGLQJ PHPEHU OHDG SDUWQHU DQG WKH ODUJHVW ¿QDQFLDO FRQWULEXWRU RI WKH &&$& ± WKH ¿UVW JOREDO HIIRUW WR WUHDW WKHVH SROOXWDQWV DV D FROOHFWLYH FKDOOHQJH 7KH ZRUN RI WKH &&$& LV FRPSOHPHQWDU\ WR WKDW RI WKH 8QLWHG 1DWLRQV )UDPHZRUN &RQYHQWLRQ RQ &OLPDWH &KDQJH ZKHUH &DQDGD LV ZRUNLQJ Environmental Science & Engineering Magazine


ES&E NEWS with other parties to achieve substantial reductions in greenhouse gas emissions.

Peter J. Laughton, P. Eng.

Parry Sound Receives AWWA Water Landmarks Award The Old Waterworks Pumphouse in Parry Sound, Ontario, has been honored as a Canadian Water Landmark by the AWWA. It recognizes the people who operated the Old Pump House which kept Parry Sound residents safe from LOOQHVV DQG ÂżUH IRU \HDUV The Old Pumphouse, the only shoreOLQH EXLOGLQJ UHPDLQLQJ IURP WKH WK century in Parry Sound, also received a Heritage Designation from the Province of Ontario. As part of the waterworks designed for the town by John Galt, it demonstrated the technical and scientific achievements of its era. Mark Carr, executive director of the Ontario Water Works Association, preVHQWHG WKH DZDUG RQ $XJXVW Âł,W LV QRW SUHVHQWHG OLJKWO\ ´ VDLG &DUU Âł7KLV LV DQ international award that looks at the hisWRULFDO VLJQLÂżFDQFH RI ZDWHU IDFLOLWLHV throughout Mexico, the United States and Canada and it doesn’t have to be awarded every year...the last time it was DZDUGHG ZDV WR WKH +RRYHU 'DP in Nevada, and a reservoir and gatehouse in Cambridge, Massachusetts.â€? For a landmark to receive the award LW PXVW EH RYHU \HDUV ROG DQG PXVW EH recognized in the community as a popXODU YDOXHG DQG KLVWRULFDOO\ VLJQLÂżFDQW property. While the hilltop water tanks are gone and the pipes replaced, the Old Pumphouse facility remains as a home on the shores of Georgian Bay.

Consulting Engineer

Environmental Engineering Services

Alliston, Ontario CANADA

p.laughton@pjlaughtonenv.com

tel: +1.705.434.9563 cell: +1.289.221.4220

Consulting Engineers and Scientists 1-800-265-9662 www.rjburnside.com

Zimbabwe inventor receives 2013 Stockholm Water Prize Dr. Peter Morgan of Zimbabwe has received the Stockholm Water Prize for his life-long work to protect the health and lives of millions of people through improved water and sanitation technologies. King Carl XVI Gustaf of Sweden presented the prize to Dr. Morgan on September 5, at a Royal Award Ceremony during the World Water Week held in Stockholm. continued overleaf... www.esemag.com

September/October 2013 | 79


ES&E NEWS An estimated 1.8 billion people live without access to safe drinking water and 2.5 billion people do not have access to adequate sanitation. The consequences are disastrous. Diseases caused by unsafe water and inadequate sanitation kill more than 5,000 people each

20 th

ANNUAL!

day. This year’s laureate, Dr. Morgan, has spent the last four decades inventing and advancing low-cost practical solutions to provide access to safe sanitation and clean water that are being used by millions of people worldwide. “Many currently existing solutions

ENVIRONMENTAL

to provide clean water and sanitation are unaffordable, impractical and out of reach for the world’s poorest people,” said the Stockholm Water Prize Committee in its citation. “As a result of Dr. Morgan’s pioneering work, countless communities now enjoy safer water, a cleaner environment and quality of life.” Several of Dr. Morgan’s most prominent innovations, including the “B” type bush pump and the Blair Ventilated Improved Pit (VIP) latrine, have been adopted as the national standard by the government of Zimbabwe. Huge numbers of Blair VIP latrines, designed for both families and schools, have been built and serve millions of people in Zimbabwe alone. Many more have been built worldwide. Dr. Morgan also created the “Upgraded Family Well”, a concept where families can support themselves, which now helps half a million people improve the quality of water obtained from traditional wells. www.siwi.org

www.envirogate.ca

COMPLIANCE

ESSENTIALS 2013 For Managers, Consultants and Practitioners

November 25-27, at the Mississauga, Ontario, Grand Banquet & Convention Centre. Proven courses to ensure environmental compliance and due diligence at your facility!

November 25 Environmental Regulations & Compliance, 2013 November 26 Waste & Wastewater Compliance & Due Diligence November 27 Waste (Not):

Preparing for Ontario’s New Reduction & Stewardship Rules

For further information, please contact: Judy Earl, Envirogate Event Management, Tel: 416-920-0768, Fax: (416) 920-0620, E-mail: judy@templegateinfo.com 80 | September/October 2013

Environmental Science & Engineering Magazine


Water Treatment

Innovative use of siphon hydraulics will reduce capital and operating costs at Nanaimo’s new WTP By Matthew Lozie

C

onstruction is currently unGHUZD\ RQ WKH JUHHQÂżHOG South Fork Water Treatment Plant (WTP), which is designed to supply 116 ML/d of membrane ÂżOWHUHG ZDWHU WR WKH &LW\ RI 1DQDLPR British Columbia. The design incorporates a unique siphon feature that replaces traditional permeate pumps used on the downstream side of a submerged membrane plant. The design presented some interesting challenges, such as plant siting and layout, and plant and siphon hydraulics. Located on the east coast of Vancouver Island, the City of Nanaimo

(Pop.90,000) has experienced continuous growth for more than ten years. Several key factors led to the City’s decision to build a new water treatment plant to serve the community. Among them was the fact that its existing water supply is from the South Fork Dam, located on the South Nanaimo River, and that the City currently uses gaseous chlorine for disinfection. Since 2000, the Province of British Columbia, through its regional Health Authorities, has implemented higher water quality standards. The Vancouver Island Health Authority had in the past accepted a chlorination-only dis-

Figure 1: South Fork water treatment process.

Figure 2: Building layout of the South Fork Water Treatment Plant. www.esemag.com

infection strategy, but the source water quality did not meet the current, more stringent water quality standard, or its QHZ ¿OWUDWLRQ GHIHUUDO FULWHULD These factors, together with Nanaimo’s recent and projected population growth, paved the way for a Water Supply Strategic Plan. It outlined the longterm vision of water supply for the City DQG LGHQWL¿HG WKH QHHG IRU D QHZ ZDWHU treatment plant. Treatment selection Associated Engineering, in partnership with MWH Canada, was retained WKURXJK D TXDOL¿FDWLRQ EDVHG VHOHFWLRQ to perform design services that included piloting several water treatment processes. A detailed review of water treatment options led to the following that were piloted in 2009 and 2010: 1) Conventional treatment using dissolved air flotation (DAF) and granular media filtration. 2) Direct filtration using granular media filtration. 3) Submerged membrane filtration. Following a review of the pilot study results, the options were evaluated using a Triple Bottom Line + Risk approach to form a basis from which the City could make a transparent, informed and calculated decision. The membrane option scored the highest and also had the lowest risk. It offered a robust and responsive treatment scheme, with the least amount of operator attention required to address seasonal turbidity spikes in the source water. Hydraulics The overall hydraulics of the water supply system played an important role in plant site and membrane technology selection, and the evaluation of gravity YHUVXV SXPSHG ÀRZ 7KH SODQW VLWH ZDV selected to intercept the hydraulic grade line that currently runs from an intake on South Fork Dam to the distribution system within the City. There was suf¿FLHQW H[FHVV SUHVVXUH KHDG WR SHUPLW water to be gravity fed into the new continued overleaf... September/October 2013 | 81


Advertiser INDEX

Company

Page

ACG Technology ...........................83 American Public University ..........65 American Public Works Association ....................................70 American Water/Terratec Env. .....22 Associated Engineering .................5 Avensys ..........................................41 Bishop Water Technologies .........58 Brentwood Industries....................58 Burkert Fluid Control Systems.....33 C&M Env. Techologies ..................25 Cancoppas .....................................15 CIMA Canada .................................42 Cole Engineering ...........................69 Corrugated Steel Pipe Institute ....84 Delcan .............................................24 Denso .............................................36 Endress + Hauser ..........................19 Envirocan ......................................83 Geneq .............................................59 Greatario ........................................67 Greyline Instruments.....................44 Grundfos ........................................46 Gunnell Engineering .....................38 H2Flow ............................................42 Halogen Valve Systems ................61 Hanna Instruments Canada ..........29 Hoskin Scientific......................31, 45 Huber Technology ...........................9 Indachem ........................................38 Infilco Degremont .........................39 IPEX ................................................13 Kemira ............................................50 KSB Pumps ....................................48 Landshark Drilling .........................56 Maple Reinders Group ..................32 Master Meter ....................................3 Monitario ........................................35 MSU Mississauga ..........................21 NETZSCH........................................51 Noble...............................................17 Orival ..............................................68 Osprey Scientific ...........................59 Pro Aqua.........................................37 ProMinent .........................................2

Water Treatment plant, where the hydraulic grade would be reduced, due to losses DFURVV FRQWURO YDOYHV RSHQ ÀRFFXlation tanks, and membranes. Water is then conveyed from a new treated water clearwell to the distribution system. Using siphon operation is an important feature of the South Fork WTP. As energy conservation was a key project target, there was a strong impetus to take advantage of a sloping site by using a siphon as WKH GULYLQJ IRUFH IRU ¿OWUDWLRQ UDWKHU than permeate pumps - the typical approach. The design made full use of the selected site grade by placing the clearwell downhill from the WTP. Through an inter-disciplinary review and a preliminary design Value Engineering session, the design team determined that the optimal plant layout would incorporate a gallery below the membrane tanks. It would house the individual membrane permeate valves required for siphon control. Placing this gallery on the downhill side of the WTP greatly reduced the excavation required. Submerged membranes using the siphon approach were deemed more appropriate than pressurized PHPEUDQHV WR ¿W ZLWK WKH H[LVWLQJ system hydraulic grade line. The driving factors were the lower operating trans-membrane pressure required to operate submerged membranes and the feasibility of placing pre-treatment open basins, upstream of the membranes. After a submerged membrane system procurement phase was completed, GE Water & Process Technologies Canada was awarded the procurement contract.

SEW-Eurodrive ..............................23 Smith & Loveless...........................49 Solinst Canada...............................27 SPD Sales .......................................47 Stantec............................................44 Waterloo Biofilter Systems ...........23 Waterra ...........................8, 43, 57, 63 WTP Equipment .............................26 XCG Consultants ...........................55 Xylem ................................................7 Xypex ..............................................53

82 | September/October 2013

Siphon operation The siphon will be primed by airdriven ejectors that are placed at high points in the permeate piping. These ejectors will eliminate air during plant start-up and maintain vacuum conditions within the permeate piping during operation. One end of the siphon will be connected to individual headers tied to the submerged

membrane cassettes. The other end of the siphon will be submerged in the clearwell. Once the permeate valves are opened, the siphon will operate by JUDYLW\ ÀRZ DQG ZLOO EH FRQWUROOHG E\ permeate valves. The permeate control valves will be placed on each membrane train WR FRQWURO WKH SHUPHDWH ÀRZ UDWH As each tank of submerged membrane cassettes becomes fouled during normal operation, these control valves will compensate for the varying membrane trans-membrane pressure required to maintain operDWRU VHOHFWHG ÀRZ UDWH WKURXJK WKH membranes. During the detailed design phase it was important to ensure that the pipe and ancillary equipment were rated for vacuum conditions. Any pipe that will be subjected to vacuum conditions requires proper material selection and wall thickness to avoid buckling. The UV equipment and pipe couplings had to be rated for partial vacuum conditions. It was also critical that any source of air leak into the siphon be eliminated. Chemical injection lines and sample pump lines will EH ¿WWHG ZLWK DXWRPDWHG LVRODWLRQ valves or backpressure valves to avoid accidental air leaks, that could jeopardize siphon operation. Long-term sustainability Construction of the South Fork WTP is scheduled for completion in early 2015. Once operating, it will be the largest siphon-powered membrane plant in North America. The plant will provide the residents RI 1DQDLPR ZLWK KLJK TXDOLW\ ¿Otered water through a robust memEUDQH ¿OWUDWLRQ SURFHVV WKDW FDQ UHspond to the turbidity spikes common to the South Nanaimo River. Innovative use of the siphon saves capital costs by eliminating permeate pumping and its associated building footprint costs, as well as long-term operating costs for utility power and maintenance. Matthew Lozie, P.Eng. is with Associated Engineering. E-mail: loziem@ae.ca

Environmental Science & Engineering Magazine



CSPI and ES&E: standing together in the trenches, shoulder-to-shoulder, coast-to-coast across Canada. For 25 years, we’ve shared a deep commitment to communicating news and information that promote better understanding and improved, environmentally responsible water management solutions. As Canadians, we’re all in this together; and through technological innovation and a more prudent, holistic approach to real life problem solving, our industry is helping Canada achieve sustainable success in its long-term stewardship of our precious natural resources. The members of the Corrugated Steel Pipe Institute congratulate Environmental Science and Engineering magazine for a quarter century of success in providing an impartial journalistic forum to acknowledge, address and disseminate relevant news and technical information to help realize this important goal.

For more news from In The Trenches visit us at cspi.ca


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.