OT Implant Manual 2016

Page 1

Made in Italy

Instructions manual for dentists and dental technicians


COMPONENTS AND ACCESSORIES MANUAL

OT EQUATOR BIOLOGIC ABUTMENT ONE BRAND, MULTIPLE SOLUTIONS OT EQUATOR BIOLOGIC ABUTMENT can be considered as the most advanced and versatile attachment for titanium implants. Created as an evolution of the OT Cap sphere, it maintains the advantages of its size minimization. It is also available for every fixture brand and model. The flexibility of this multi-purpose system ranges from overdenture to OT EQUATOR BIOLOGIC ABUTMENT, single attachment, from multiple types of bar to fixed rehabilitations.. A technique for immediate loading has also been developed that allows you to apply a temporary THREAD-REINFORCED ACRYLIC bridge attached to the implants on the patient in the same session following surgery. To complete the system, it was decided to use the OT EQUATOR attachment for a new series of titanium transmucosal MINI-MEDIO IMPLANT. Immediate loading in a combined prosthesis can be distributed more evenly on these reduced diameter fixtures thanks to the passive “SEEGER BAR”. The same advantages are obtained in the “SEEGER BRIDGE” fixed prosthesis.

BIOLOGY AND PARALLELISM This system has solved two problems. By mounting the OT Equator Biologic attachment during surgery instead of the healing screw, the ligament formed between the soft tissue and the titanium abutment remains a defense with the passage of time.

2

“SEEGER BRIDGE” FIXED PROSTHESIS

The screwing rotating system between the attachment and the implant (two mechanized and precise planes) creates a perfect closure that allows for hardly any infiltration. In contrast, other systems (such as MUA) with a male and a female hexagonal coupling are inserted in contact with a through screw, which more seldom than not reveal inaccuracies under a microscopic inspection. Furthermore, the screw threading from the outside to the inside of the implant is a potential conductor channel of germs and bacteria that may contaminate the interior of the fixture. Parallelism: 70/80 degrees of divergence are recovered with the Equator system in a very simple way without any future problems of unscrewing or the breakage of screws. The revolutionary concept of this type of prosthesis lies in the retention system, no longer entrusted to the screw alone, but assisted by the SEEGER elastic element inserted in the undercut of the OT EQUATOR attachment. The creation of any bridge is a simple operation thanks to the tolerances calculated between the attachment and the prefabricated parts that are used for its construction. The system has the prerogative of simplifying the technique of the fixed prosthesis screwed on implants in all its operating phases, with immediate loading ones as well as deferred loading, and also with divergences over 70 degrees. The system is presented as a universal technique thanks to the versatility of the OT Equator attachment, which can be applied to all types of implants on the market. It also addresses cases (with amazing simplicity) where there are already various implant types and intends to transform previously overdentures into fixed prostheses, through the insertion of additional fixtures.


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS OT EQUATOR BIOLOGIC ABUTMENT (O.B.A.)

The OT Equator Biologic Abutment attachments for a Seeger Bridge fixed prosthesis are custom made for all types and brands of implants in the world The attachments for well-known implant brands are shipped on the same day. Lesser known implants are shipped within 3-4 days of order.. REF. AT ORDER FORM DATE_______________________ ________________________

DENTAL TECHNICIAN

DENTIST

DISTRIBUTOR

NAME CITY E-MAIL LOCAL DISTRIBUTOR

IMPLANT BRAND TYPE

COMPONENTS AND ACCESSORIES

Autoclavable Assortment KIT 42 OBA attachments Customized on demand.

COD/REF

DIAMETER

EXAGON: AGON: POSITION

EXT INT

HEIGHT OF TRANSMUCOSAL

QUANTITY

COD/REF

QUANTITY

NOTE

Mod. 023 Rev.02 of 19-04-2016

(H) heights of the abutments: - For internal hexagon implants (H) from 0.5 to 7 mm - For external hexagon implants (H) from 2 to 7 mm

Please, fill this form out and send it through email to ordini@otimplant.it or through fax to n. +39 +39-051-42-14-884

To order, please download the order form from the website: www.otimplant.com

REF. AK42 IMPORTANT: THE ONLY SERVICE IN THE WORLD Our laboratory is able to identify and build to measure the OT Equator Biologic Abutment attachment for unknown implants or for those difficult to identify, even if they are already in the patient’s mouth. In such a case, it is necessary to provide one or more of the following information: • • • •

a healing screw an abutment with a screw removed from the implant an impression made with elastic material taken from the inside of the implant an intraoral or panoramic x-ray

3


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE� FIXED PROSTHESIS

OT EQUATOR BIOLOGIC ABUTMENT - SURGICAL PHASE

The OT Equator Biologic Abutment attachment should always be mounted on the head of the implant during surgery instead of the healing screw and should not be removed again. By doing this, you achieve an epithelium-connective biological junction that ensures an effective barrier against bacterial infiltration, significantly reducing the risk of periimplantitis.

BIOLOGIC EFFECT

Free gums Hemidesmosomal attachment Connective attachment

To maintain the health of the gingival tissues, the OBA attachment will no longer be removed. All subsequent sessions with the patient (impression taking, prosthesis testing and application) will be carried out on the sphere of the OT Equator Biologic Abutment. As there is no further need to work inside the fixture, all sessions are brief and without anesthesia since they pose neither discomfort nor pain to the patient.

4


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

TRANSFERS OF THE IMPRESSION AND FIXED SEEGER BRIDGE PROSTHESIS ANALOGUES OT Equator Inox analogues

Titanium transfer with screw for pick-up impression

Ø 4 mm

Plastic snap transfer for taking impressions

Ø 5 mm

OT Equator analogues in aluminium Plastic snap immediate-loading Mini Transfers

Ø 4 mm

5


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS DIVERGENCE ACRYLIC TEST BLOCK

To ensure that the prosthesis fits on divergent implants, we need to build a very solid and rigid acrylic block with embedded Extragrade titanium cylindrical abutments, appropriately positioned with the indented rim in the direction of the undercut. The acrylic block should be tested on both the model and in the patient’s mouth. If these tests are successful, it confirms that the prosthesis fits properly and that the model replicates the patient’s mouth precisely. By inserting and removing the prosthesis from the model, it is possible to see the insertion line that the dentist will repeat in the patient’s mouth.

ACRYLIC PLATE ARTICULATION IMPRESSION + WAX WALL Since the OT Equator Biologic Abutment attachment is already fixed in the patient’s mouth and should no longer be removed, the dentist can perform some tests in a new and simpler way compared to previous techniques. The acrylic plate, with two retentive caps inserted and with the wax wall above, will prove stable on the attachments in the patient’s mouth, allowing the dentist to create an occlusal plane on the wax without having to remove it and return it to the patient’s mouth again and again.

Thanks to the stability of the wax block (once the occlusal plane and the vertical dimension are defined), the patient leaves an impression in the wax with “OPEN-CLOSE-OPENCLOSE” movements with the antagonist teeth (the intercuspal in neuromandibolar position). The dentist also confidently obtains the centric relation position.

6


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE� FIXED PROSTHESIS

STABLE TEETH TEST IN THE MOUTH ON THE ATTACHMENTS With the models mounted in the articulator, the wax is removed from the acrylic plate. The technician blocks the test teeth (also commercial teeth) on the plate with wax and completes the modeling of the prosthetic body by giving it the size and aesthetics corresponding to those of the finished prosthesis

The acrylic plate with the teeth mounted in wax (stable in the mouth on the OT Equator attachments) allows the patient to try out the phonetics, to judge the aesthetics and possibly make suggestions. The dentist can technically evaluate the work at the same time.

FINISHED PROSTHESIS Finished prosthesis following the prosthetic protocol. These three tests performed on the patient in just two sessions of about 20 minutes each make it possible to finish the prosthesis with the certainty of delivering an aesthetically and technically perfect functional prosthesis to the patient.

7


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

FIXED PROSTHESIS: CYLINDRICAL ABUTMENTS IN EXTRAGRADE TITANIUM + CASTABLE HOUSING Extragrade cylindrical abutments in titanium with through-screws and castable housing

Extragrade cylindrical abutments in titanium without through-screws and castable housing

Extragrade cylindrical abutments in titanium with through-screws are used in all prostheses where the divergence does not create any aesthetic problems through leakage of the dental arch screws.

The screwless Extragrade titanium cylindrical abutments are used to build the “Seeger Bridge” fixed prosthesis on extremely divergent implants, taking advantage of the undercut as a retentive interlock with a single Seeger and in this way achieving a “snap” retention.

To gain experience using only the “snap” retention, you can begin by using cylindrical abutments with screws. Finish the job by closing the holes for the screws and use only Seegers without screws. If the prosthesis were to have stability problems later on (highly unlikely), you can open the hole and insert the screw.

Ø 3.5 mm

Straight (0°)

Bridge built with Extragrade abutments with through hole to be used without the screws and closed for aesthetic reasons

Ø 4 mm

Angled 15° Ø 5 mm

H 11.5 mm

8

H 6 mm

H 4 mm

H 2 mm

White Seeger

Pink Seeger (lab use)

Bridge finished with aesthetic “snap” retention (with only Seegers). If the prosthesis were to present signs of instability over the passage of time, the hole can be opened and a screw inserted.


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE� FIXED PROSTHESIS

FIXED PROSTHESIS: CYLINDRICAL ABUTMENTS IN EXTRAGRADE TITANIUM + CASTABLE HOUSING

To overcome the undercut of the implants during the insertion of the prosthesis, the Extragrade titanium cylindrical abutments should always be mounted with the indented rim in the direction of the undercut. The screwless abutments can be externally filed down and adapted to achieve any aesthetic advantages. Check by using the mask to make the most of the space available.

Build a robust structure with plastic bars and complete the shaping of the wax. The shape of the structure should be built and modeled on the basis of personal preference (adhering to the gum or raised or other concepts still). Characteristics: it should be rigid and strong. In applying the coating, take care with the Seeger housing in the castable abutments.

(1) Firstly secure the Extragrade incisors cylindrical abutments without through screws with anaerobic cement. (2) Insert a wax pin in the Extragrade cylindrical abutments with through screws, spread the cement on the outside of the abutment and in the casting hole. (3) Insert the casting in position. (4) Remove the wax pin from the abutment, which cleans the hole of excess cement as it comes out. (5) Insert and tighten the screw in the clean hole of the abutment.

1

2

3

4

5

9


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

EXTRAGRADE CASTABLE CYLINDRICAL ABUTMENTS WITH AND WITHOUT SCREWS - SINGLE SEEGER “SNAP” RETENTION Castable Extragrade cylindrical abutments with and without screws

without screws

Pour the coating in the hole of the cylinder up until it touches the castable model.

with screws

Castable Extragrade cylindrical abutments: Coating for cobalt-chrome castings. The internal coating chamber before casting

10

With a fine tipped probe, carefully fill the inside of the castable cylindrical abutment (which is the housing of the Seeger) continue and fill to the brim with the coating.

Carefully clean the Seeger housing (molten castable) using the special burr, before inserting the Seeger spring.


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

EXTRAGRADE CASTABLE CYLINDRICAL ABUTMENTS WITH AND WITHOUT SCREWS - SINGLE SEEGER “SNAP” RETENTION In order to obtain the “snap” retention (Seeger only without the screw), it is necessary to take advantage of the undercut between the implants. This choice should be made by the dental technician in the planning stages according to the following objectives: ensuring the stability of the prosthesis, preserving the aesthetics and, if possible, avoiding problems associated with screwing inside the patient’s mouth. The cylindrical castable abutments are mounted with the indented rim in the direction of the implant’s undercut. The plastic bars can be filed to place them in the best position and to mount the teeth in aesthetic position once the work is finished, despite the divergence between the implants.

11


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

FIXED PROSTHESIS: SEMIFINISHED TEMPORARY IMMEDIATE LOADING BRIDGE IN THREAD-REINFORCED ACRYLIC Titanium cylindrical abutments with through holes

1.8 mm

Semi-finished bridge (designed and built previously) dug out in the gingival area, reduced to an individual print holder

After surgery, the impression is taken with the semi-finished-bridge using the Mini Transfer, recording all the gnathologic data.

3 mm

Model cast in quick-setting plaster and silicone mask

H 6 mm

H 11.5 mm

H 4 mm

Before inserting the thread into the through-hole abutments, dull it on the flame

H 2 mm

White Seeger

Pink Seeger (lab use) Mini Transfer

12

Thread-reinforced structure

Semi-finished temporary bridge. With the palatal area eliminated and the teeth positioned in the mask, only the external part of the dental arch is used.


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

FIXED PROSTHESIS: SEMIFINISHED TEMPORARY IMMEDIATE LOADING BRIDGE IN THREAD-REINFORCED ACRYLIC The titanium cylindrical abutments can be filed and adapted in relation to the spaces, using the mask with the teeth in position. The reinforcement of the thread reinforced brige, once adopted, has been masked with matting paint. Refilled bridge with self-curing acrylic.

The titanium cylindrical abutments with through holes have no extragrade indented rim. The extragrade indented rim should be made with the utmost care with a burr during the work, or with the finished prostheseis, in the position corresponding to the divergence of the plants. It is important that the Seegers are loaded with the opening in the direction of the indented rim, which corresponds to the implant undercut.

The thread-reinforced acrylic bridge is finished and delivered to the dentist in about 2 hours. Even with temporary bridges, you should follow the insertion lines by placing them properly on the model and in the patient’s mouth. In this case you should insert the bridge beforehand on the incisor attachments by holding it at an angle in the direction of the implant, then compress it on the molar teeth at the same time and snap it into place.

13


COMPONENTS AND ACCESSORIES MANUAL

OT EQUATOR ATTACHMENT FOR OVERDENTURE

OVERDENTURE: OT EQUATOR ATTACHMENT IN TITANIUM + TIN COATING (Rhein ‘83 product)

Ø 4.4 mm

Ø 4.4 mm

To obtain a resilient retention with OT Equator attachment, use the OT Cap Normo caps made by Rhein ‘83

H 3.3 mm

H 2.1 mm

Ø 4.4 mm

By respecting the technical recommendations, the OT Equator attachment presents ideal conditions to be used successfully due to its size and retention; it works well in all such projects where a minimum of 3-4 implants form a tripod or a quadrilateral. In these cases, the prosthesis will present a good stability and the caps will last much longer.

14

H 3.3 mm

H 2.1 mm

Ø 4.4 mm

OT Equator with the TiN coating produced by Rhein ‘83 is a rigid retentive attachment and is used according to the instructions manual. For its size, the OT Equator attachment is applicable to any removable prosthesis. The retentive sphere coated in TiN has a protected surface with a hardness of more than 1600 Vickers. The OT Equator attachment is a rigid attachment without resilience. It is not indicated for use with a prosthesis with a single attachment. By using retentive caps of various colors and retention inserted in the stainless steel container, you can achieve the regulation of the removable prosthesis’ hold according to the prosthetic case.

The attachment, including the container and the retention cap, results in having a reduced size yet with a rigid retention. In making the OT Equator attachment compact, very retentive yet rigid results were achieved. The choice of the OT Equator attachment should be decided on the basis of these features. Cases of lower prosthesis with only two OT Equator attachments on two implants (close and aligned to each other) may encounter problems when the patient chews on the molars.

When two OT Equator attachments are in an interforaminal region, it is advisable to use a normo OT Cap made by Rhein ‘83 in order to obtain a resilient retention, which offers the same hold yet results in being more resilient.


COMPONENTS AND ACCESSORIES MANUAL

TITANIUM ROOT POSTS

OVERDENTURE: TITANIUM OT EQUATOR ROOT POSTS + TIN COATING Titanium OT Equator root posts The pack contains:

1 TiN-coated OT Equator root post 1 stainless steel container 2 elastic retention caps 1 protective washer

Use “Mooser” type cutters for boring root canals.

The OT Equator titanium root canal posts are extremely versatile and they are even used in small vertical spaces due to the low size of their attachment. Two MINIMEDIO-IMPLANTS have been linked with two root posts set on the roots in this prosthesis.

OT Equator Root canal pins: Upper Toronto Snap on the roots. It’s quite a controversial project, but we wanted to intentionally bring it back to its originality that could prove useful as a starting point for tackling different problems.

15


COMPONENTS AND STERILIZABLE ACCESSORIES MANUAL

MINI - MEDIO IMPLANT

MINI MEDIO IMPLANT: MONOBLOCK IMPLANTS WITH OT EQUATOR ATTACHMENTS + TIN COATING

SURGICAL MANDREL

Ø 2.7 mm

Ø 3.2 mm

Extention for surgical mandrel and ratchet

AUTOCLAVABLE BURRS KIT IMPLANTS PACK

Ratchet wrench

The STUDIO-LABORATORY-STUDIO KITS include 4 MINI MEDIO IMPLANTS, or 4 titanium OT EQUATOR attachments, and contain everything needed to rehabilitate an edentulous patient from surgery to the prosthesis with a “SEEGER BAR” dual-structure combined overdenture prosthesis.

RETENTIVE SYSTEM OT CAP DARK BLUE BOX SPHERICAL RETENTION

ASSORTED COMPONENTS FOR SEEGER BAR SPECIAL PRICE ONLY WHEN COMBINED WITH 4 MINI MEDIO IMPLANTS OR 4 OT EQUATOR ATTACHMENTS

16

OT BAR MULTIUSE RETENTIVE SYSTEM LIGHT BLUE BOX RETENTION BAR

ASSORTED COMPONENTS FOR SEEGER BAR SPECIAL PRICE ONLY WHEN COMBINED WITH 4 MINI MEDIO IMPLANTS OR 4 OT EQUATOR ATTACHMENTS


COMPONENTS AND STERILIZABLE ACCESSORIES MANUAL

MINI - MEDIO - IMPLANT

MINI MEDIO IMPLANT: MONOBLOCK IMPLANTS WITH OT EQUATOR ATTACHMENTS + TIN COATING These are monoblock implants with a selftapping screw that goes into the bone smoothly. The design and the wide surface of the screw favor the primary hold. The TiN-coated OT Equator attachment has a surface hardness of more than 1600 Vickers. The retentive caps should always be used by inserting them in the stainless steel container. The center of gravity of the attachment at a low gingival level does not create any leverage play. The assortment of caps with two types of hold allows you to manage the retention of the denture.

Four Mini Medio Implants: despite the divergence of the monoblock implants, the mesostructure is locked onto the implants in a simple, safe and passive way using the “Seeger Bar” system.

In the Mini Medio Implants, the threaded hole on the head of the OT Equator attachment allows you to use these implants for fixed prosthesis cases. Being that the implant is a monoblock, it can also be used for single-tooth replacement or for small bridges.

17


COMPONENTS AND ACCESSORIES MANUAL

“SEEGER BRIDGE” FIXED PROSTHESIS

REF. KF

Ø 3.2 mm

REF. IM2708 REF. IM2711 REF. IM2713 REF. IM2715

REF. MU35

REF. FP152 REF. FC19

Ø 2.7 mm

REF. IM3208 REF. IM3211 REF. IM3213 REF. IM3215

H 1.8 mm

REF. CMTFP

H

H 3 mm

ø MM 3.5

ø MM 4

ø MM 5

ø MM 3.5 REF. MTSEG ø MM 4.0 REF. MT40SEG ø MM 5.0 REF. MT50SEG

REF.CMTB30FP

H

REF. MTSFEG Straight 90°

REF. FC24 REF. AT REF. M27

ø MM 4 REF. CMC ø MM 5 REF. CM50C

REF. MTEG15SF Angled 15°

REF. M32

REF. B08

REF. KA42

ø MM 4 REF. CMEG40C

REF. VT4

REF. B11 REF. B13 REF. B15

REF. VC

REF. TTVL

ø MM 4 REF. MCEG15SF

REF. VT6

REF. VT8 REF. CHC

REF. TP2 REF. CMCMMI

REF. SCCK

REF. KRK

18

REF. TPM2

REF. AI412 REF. AI502

ø MM 3.5 REF. CMTGL ø MM 4 REF. CM40GL ø MM 5 REF. CM50GL

REF. VT10

REF. VXL

REF. TCV


COMPONENTS AND ACCESSORIES MANUAL

REF. SM6

“SEEGER BRIDGE” FIXED PROSTHESIS

INDEX

REF. KQC125

2 3 4 5

REF. SRM6 REF. SBS6

REF. KQ125

REF. SRL6

Ø 1.4 - 7 mm

Ø 1.7 - 9 mm

Ø 1.8 - 10 mm

REF. ACSES

REF.???? P1810 REF. REF. P1709 REF. P1407 REF. FM79

REF. SIDC

REF. SICS

REF. REF.????? FM910

REF. CC2D*

REF. 030*

REF. 130*

REF. ASSE

REF. FSS

OT Equator Biologic Abutment attachments Surgical phase - Biologic effect Transfers of the impression and fixed Seeger Bridge prosthesis analogues

6

REF. MBI

One brand, multiple solutions

Divergence acrylic test block - acrylic plate articulation

impression + wax wall

7 8 9 10 11 12 13 14

Stable teeth test - Finished prosthesis

15 16 17 18 19

Cylindrical abutments in extragrade titanium + castable housing Cylindrical abutments in extragrade titanium + castable housing Extragrade castable cylindrical abutments “snap” retention Extragrade castable cylindrical abutments “snap” retention Immediate loading: thread-reinforced acrylic bridge Immediate loading: thread-reinforced acrylic bridge Overdenture: titanium OT Equator attachment + tin coating (Rhein ‘83 product) Overdenture: OT Equator root posts + tin coating Mini Medio Implant Mini Medio Implant Components and accessories manual Index

TO BE USED WITH THE BLUE HANDLE

*Rhein ‘83 product

19


MOD. 002 REV.02 22/04/2016

Via Sebastiano Serlio, 26 - 40128 - Bologna - Tel. (+39) 051 4208111 - Fax 051 4214884 info@otimplant.it - www.otimplant.com


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.