Parts & Operation Manual
25/09/2014 Issue 5 2018
Page 1
Introduction
Dear Customer
We take this opportunity of welcoming you as the owner of a Robertson Machine. We want your machine to be the most efficient and productive piece of equipment you have. This small manual will help you to achieve this objective.
The correct parts and maintenance of your machine is very important to prevent downtime and equipment damage.
Warranty
Robertson® Manufacturing Ltd warrants new products sold by us to be free from defects in material and workmanship twelve months after delivery to the initial user. This warranty is for the replacement or repair of any part found to be defective during the warranty period. This warranty excludes any freight cost incurred by the dealer in giving effect to the warranty and specifically excludes all normal maintenance costs. Replacement parts provided under the terms of this warranty are covered for the remainder of the warranty period applicable to the product in which they are installed as if such parts were original components of that product.
Pre-delivery and warranty registration forms must be returned within 30 days of delivery.
These forms are found in your operators manual on the last few pages. This is to help both you as the customer and Robertson Manufacturing staff assist with any issues should they arise.
It is also Manditory that All bolts are checked and tightened, weekly for the first 4 weeks (or every 20hours of operation), then monthly (or every 100 hours operation).
M8 - 16 ft-lbs
M10 - 31 ft-lbs
M12 - 55 ft-lbs
M16 - 137 ft-lbs
M20 - 267 ft-lbs
With Load Cell weighing machines, this is crucial to maintain accurate weighing and to eliminate failure.
25/09/2014 Issue 5 2018 Page No. 2
Tools Required For Maintaining Operation 1 1/2 Ring Spanner x 2 30mm Ring Spanner x 2 24mm Ring Spanner x 2 19mm Ring Spanner 18mm Ring Spanner 13mm Ring Spanner Flexi Tube Grease Gun Page 2
Parts Ordering Information
When ordering components from this manual please state the section letter and item number of the component required EG Section A-3 Item No 4. Also find the serial number on the machine which can be found on the drawbar chassis tag.
25/09/2014 Issue 5 2018
Page No. 4
Page 4
Chassis Tag Location
5/05/2014 Section Wiring Page No. 2 Issue 5 2018 Pin No Description Colour 5 Earth Control Line Black 2 12 Volt Line Red Electric Floor Speed Controller Option Wiring Diagram Wiring Manual Parts List Page 19 ©Design Copyright Hustler Equipment™
12/05/2014 Section A-1 Page No. 1 Issue 5 2018 Main Machine Assembly Manual Exploded Front View 22 1
17 1 16 1 4 1 20 1 21 1 23 1 38 1 Page 28 ©Design Copyright Hustler Equipment™
Top Number = Item Number Bottom Number = Quantity
12/05/2014 Section A-1 Page No. 2 Issue 5 2018
Exploded Drive
Number = Item Number
Number = Quantity 3 1 13 1 9 1 12 1 11 1 35 1 29 1 6 2 5 1 27 1 14 1 Page 29 ©Design Copyright Hustler Equipment™
Main Machine Assembly Manual
View Top
Bottom
12/05/2014 Page No. 3
A-1 Page No.
Issue 5 2018
Section
3
Main Machine Assembly Manual Exploded Rear
39 2 28 2 7 2 26 2 32 1 8 2 34 4 33 1 31 1 36 1 37 1 Page 30 ©Design Copyright Hustler Equipment™
Top Number = Item Number Bottom Number = Quantity
12/05/2014 Section A-1 Page No. 4 Issue 5 2018
Exploded
Top Number = Item Number Bottom Number = Quantity 22 1 18 1 19 1 25 1 2 1 1 1 15 1 24 1 Page 31 ©Design Copyright Hustler Equipment™
Main Machine Assembly Manual
Drawbar Components
12/05/2014 Section A-1 Page No. 5 Issue 5 2018 Main Machine Assembly Manual Exploded Discharged View Top Number = Item Number Bottom Number = Quantity 10 1 Page 32 ©Design Copyright Hustler Equipment™
Main Machine Assembly Manual Parts List
12/05/2014
Page No.
5 2018
Section A-1
6 Issue
Item Number Quantity Part Name Manual Section Comments 1 1 6 Cell Junction Box Cover Assembly N-1 2 1 Battery Box Including Battery M-2 3 1 Crash Rail Assembly A-8 4 1 Elevator Assembly A-2-1L 5 1 Elevator Motor Mount Assembly A-14 6 2 Elevator Motor Retainer Plate Assembly A-22 7 2 Feed Sticker 8 2 Floor Chain Assembly A-18 9 1 Floor Drive Chain Assembly A-13 10 1 Floor Drive Shaft Bearing Assembly 1 A-5 11 1 Floor Drive Shaft Bearing Assembly 2 A-6 2.5 Inch Drive Shaft Components 12 1 Floor Drive Sprocket Assembly A-3 2.5 Inch Drive Shaft Components 13 1 Floor Drive Sprocket Support Assembly A-4 14 1 Floor Hydraulic Motor Cover Assembly A-12 15 1 Floor Pressure Relief Valve Assembly A-15 16 1 Front Panel Assembly A-10 17 1 Front Screen Frame 18 1 Load Cell Drawbar Lower Cover Assembly A-27 19 1 Load Cell Drawbar Top Cover Assembly A-26 20 1 Load Cell Head Unit Mount Assembly A-25 21 1 Load Cell Side Panel Top Support Brace Assembly A-11 22 1 Load Cell Towing Fixed Bolt On Assembly A-28 23 1 Main Chassis 24 1 Manual Valve Block Assembly A-16 25 1 Mega Comby Load Cell Junction Box Rev-002 Assembly 26 2 Mudguard 405-70-R18 Wheel Assembly A-32 27 1 RE 45 Floor Reduction Drive A-23 28 2 Robertson Sticker 970mm x 135mm 29 1 SF 2000 Floor Drive Cover Assembly A-9 30* 1 Spec's Chassis Tag Assembly A-3 31 1 Tail Door Assembly A-20 32 1 Tail Door Latch Assembly A-21 33 1 Tail Door Latch Assembly 2 A-21 34 4 Top Bolster Rail Assembly A-24 35 1 Twin Floor Drive Drive Shaft Assembly A-7-3 36 1 Twin Idler Shaft 1 Assembly A-19A 37 1 Twin Idler Shaft 2 Assembly A-19B 38 1 Valve Block Cover Assembly A-17 39 2 Wagon Sticker 40 1 Single Idler Shaft Assembly A-19-C Page 33 ©Design Copyright Hustler Equipment™
Page 34 ©Design Copyright Hustler Equipment™
Elevator Assembly Short-Long Manual Parts List
Elevator Long Pre February 2014
Section A-2 Page No. 1
Elevator Short Post February 2014
12/05/2014
5
Issue
2018
Page 35
Copyright Hustler Equipment™
©Design
12/05/2014 A-2-1L Page No. 1 Issue 5 2018 Elevator Long Assembly Manual Page 36 ©Design Copyright Hustler Equipment™
Bottom Number = Quantity
12/05/2014 A-2-1L Page No. 2 Issue 5 2018 7 6 18 23 18 23 16 6 17 23 13 1 3 1 1 1 6 1 2 2 5 2 4 3 Elevator Long Assembly Manual Explode View 1
Top Number = Item Number
Page 37 ©Design Copyright Hustler Equipment™
12/05/2014 A-2-1L Page No. 3 Issue 5 2018 A DETAIL A 18 23 19 17 16 6 17 23 3 1 1 1 6 1 2 2 5 2 4 3 9 6 7 6 15 4 19 17 16 6 8 6 12 8 14 1 Top Number = Item Number Bottom Number = Quantity
Explode View
Page 38 ©Design Copyright Hustler Equipment™
Elevator Long Assembly Manual
2
Elevator Long Assembly Manual Parts List
12/05/2014
5 2018
A-2-1L Page No. 4 Issue
Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Frame 2 2 Idler Shaft Assembly A-2-1 3 1 Elevator Drive Shaft Assembly A-2-3 4 3 Nylon Strip Assembly A-2-4 5 2 Idler Sprocket Assembly A-2-5 6 1 Elevator Shaft Cover 7 6 M10 x 25 x 1.5 Pan Head Bolt 8 6 10mm Flat Washer 9 6 M10 x 1.5 Nylock Nut 12 8 12mm Heavy Flat Washer 13 1 Elevator Chain Assembly A-2-6 14 1 Motor Drive Scraper 15 4 M12 x 1.75 Nylock Nut 16 6 M12 x 40 x 1.75 Coach Bolt 17 23 12mm Spring Washer 18 23 M12 x 1.75 Nut 19 17 M12 x 30 x 1.75 HT Bolt 20* 1 Drive Shaft Idler Scraper Page 39 ©Design Copyright Hustler Equipment™
12/05/2014 A-2-1S Page No. 1 Issue 5 2018 Elevator Short Assembly Rev 1 Manual Page 40 ©Design Copyright Hustler Equipment™
12/05/2014 A-2-1S Page No. 2 Issue 5 2018 7 6 18 19 18 19 16 6 17 19 13 1 3 1 1 1 6 1 2 2 5 2 4 3 Elevator Short Assembly Rev 1 Manual Explode View 1
Top Number = Item Number
Page 41 ©Design Copyright Hustler Equipment™
Bottom Number = Quantity
12/05/2014 A-2-1S Page No. 3 Issue 5 2018 A DETAIL A 18 19 19 13 16 6 17 19 3 1 1 1 6 1 2 2 5 2 4 3 9 6 7 6 15 4 19 13 16 6 8 6 12 8 14 1 Top Number = Item Number Bottom Number = Quantity Elevator Short Assembly Rev 1 Manual Explode View 2 Page 42 ©Design Copyright Hustler Equipment™
Elevator Short Assembly Rev 1 Manual Parts List
12/05/2014
Issue 5 2018
A-2-1S Page No. 4
Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Frame 2 2 Idler Shaft Assembly A-2-2 3 1 Elevator Drive Shaft Assembly A-2-3 4 3 Nylon Strip Assembly A-2-4 5 2 Idler Sprocket Assembly A-2-5 6 1 Elevator Shaft Cover 7 6 M10 x 25 x 1.5 Pan Head Bolt 8 6 10mm Flat Washer 9 6 M10 x 1.5 Nylock Nut 12 8 12mm Heavy Flat Washer 13 1 Elevator Chain Assembly A-2-5 14 1 Motor Drive Scraper 15 4 M12 x 1.75 Nylock Nut 16 6 M12 x 40 x 1.75 Coach Bolt 17 19 12mm Spring Washer 18 19 M12 x 1.75 Nut 19 13 M12 x 30 x 1.75 HT Bolt 20* 1 Drive Shaft Idler Scraper Page 43 ©Design Copyright Hustler Equipment™
Page 44 ©Design Copyright Hustler Equipment™
Idler Shaft Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 2 assemblies per machine
Section A-2-1Page No. 1
6/05/2014
Issue 5 2018 2 1 4 1 3 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Pivot Shaft 2 1 1/8 BSPT Grease Nipple Straight 3 1 M12 x 75 x 1.75 HT Bolt 4 1 M12 x 1.75 Nylock Nut
Page 45 ©Design Copyright Hustler Equipment™
Top Number = Item Number
Bottom Number = Quantity
6/05/2014 Section A-2-2 Page No. 1 Issue 5 2018
A
B DETAIL
8 2 4 2 3 1 5 2 7 1 1 1 2 1 5 2 6 4 9 1 Page 46 ©Design Copyright Hustler Equipment™
Elevator Drive Shaft Assembly Manual
DETAIL A
B
Elevator Drive Shaft Assembly Manual Parts List
Section A-2-2 Page No. 2
6/05/2014
Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Drive Shaft 2 1 10 x 10 x 50 Keysteel 3 1 0.375 x 0.375 x 90 Keysteel 4 2 1.5 " Shaft Collar Assembly 5 2 Drive Shaft Bush Housing Assembly A-2-2-1 6 4 3/8" x 3/4" Grubscrew 7 1 Drive Shaft Idler Sprocket 8 2 3/8 x 3/8 Grubscrew 9 1 Motor Coupling Sprocket ©Design Copyright Hustler Equipment™
Drive Shaft Bush Housing Assembly Manual Parts List
Issue 5 2018
Note: There are 2 assemblies per machine
Section A-2-2-1
6/05/2014
Top Number = Item Number
Quantity
Bottom Number =
1 1 2 1 5 2 Item Number Quantity Part Name Manual Section Comments 1 1 Bush Housing Frame 2 1 1/4 Grease Nipple Straight 4 1 Bronze Bush Requires Machining After Fitting 5 2 M30 x 2.50 Nut 4 1 Page 48 ©Design Copyright Hustler Equipment™
Long Nylon Strip Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 3 assemblies per machine
Section A-2-3 Page No. 1 Issue 5 2018
13/05/2014
4 4 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Nylon Strips 2 4 M6 x 20 Countersunk Bolt 3 4 6mm Panel Washer 4 4 M6 x 1.00 Nylock Nut 2 4 3 4 Page 49 ©Design Copyright Hustler Equipment™
Short Nylon Strip Assembly Rev 1 Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 3 assemblies per machine
Section A-2-3 Page No. 1 Issue
13/05/2014
5
2018
4 4 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Nylon Strips 2 4 M6 x 20 Countersunk Bolt 3 4 6mm Panel Washer 4 4 M6 x 1.00 Nylock Nut 2 4 3 4 Page 50 ©Design Copyright Hustler Equipment™
Top Number = Item Number
Bottom Number = Quantity
Idler Sprocket Assembly Manual Parts List 1
Note: There are 2 assemblies per machine
Section A-2-4 Page No. 1 Issue 5 2018
6/05/2014
1 2 2 Item Number Quantity Part Name Manual Section Comments 1 1 Idler Sprocket 2 2 Idler Sprocket Bush Page 51 ©Design Copyright Hustler Equipment™
5/05/2014 PageNo.1 ©DesignCopyrightRobertsonManufacturing™ Section A-2-5 Issue3 2014 TopNumber=ItemNumber BottomNumber=Quantity
4 2 2 4 3 3 Item Number Quantity PartName Manual Section Comments 1 2 Floor Link Chain Assembly 2 4 Elevator Slat1 3 3 Elevator Slat2 4 2 Link Chain Joiner Assembly 1 2 A DETAILA 5201544
ElevatorChainAssemblyRev1ManualPartsList
6/05/2014 Section A-2-6 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity Elevator Chain Assembly
4 2 2 5 3 4 Item Number Quantity Part Name Manual Section Comments 1 2 Floor Link Chain Assembly 2 5 Elevator Slat 1 3 4 Elevator Slat 2 4 2 Link Chain Joiner Assembly 1 2 A DETAIL A Page 52 ©Design Copyright Hustler Equipment™
Manual Parts List
Floor Drive Sprocket Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
12/05/2014
Issue 5
Section A-3 Page No. 1
2018
1 1 3 1 2 2 Item Number Quantity Part Name Manual Section Comments 1 1 45 Tooth Sprocket 2 2 3/8" x 1" UNC Grubscrew 3 1 Spacer Plate
Page 53 ©Design Copyright Hustler Equipment™
2" Bore
Floor Drive Sprocket Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
12/05/2014
1 Issue 5
Section A-3 Page No.
2018
1 1 2 2 Item Number Quantity Part Name Manual Section Comments 1 1 45 Tooth Sprocket 2 2 3/8" x 1" UNC Grubscrew 2 1/2" Bore Page 54 ©Design Copyright Hustler Equipment™
Floor Drive Sprocket Support Assembly Manual Parts List
12/05/2014 Page No. 1 Section A-4 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 3 1 2 2 5 1 4 2 Item Number Quantity Part Name Manual Section Comments 1 1 Outrigger Shaft Support 2 2 M12 x 35 x 1.75 HT Bolt 3 1 1/4 Grease Nipple Straight 4 2 12mm Spring Washer 5 1 Grease Point Sticker 6 1 Boss Support Bush 6 1 2" Bore Page 55 ©Design Copyright Hustler Equipment™
Floor Drive Sprocket Support Assembly Manual Parts List
12/05/2014 Section A-4 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 3 1 2 2 5 1 4 2 Item Number Quantity Part Name Manual Section Comments 1 1 Outrigger Shaft Support 2 2 M12 x 35 x 1.75 HT Bolt 3 1 1/4 Grease Nipple Straight 4 2 12mm Spring Washer 5 1 Grease Point Sticker 6 1 Support Bush 6 1 2 1 2 " Bore 2 1/2" Bore Page 56 ©Design Copyright Hustler Equipment™
Floor Drive Shaft Bearing Assembly 1 Manual Parts List
Top
Bottom
6/05/2014
A-5Page No. 1 Issue 5 2018
Section
Number = Item Number
Number = Quantity
3 1 5 3 2 3 4 3 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Exit Side Bearing Housing 2 3 16mm Heavy Flat Washer 3 1 UC 211-200 Bearing Assembly 4 3 16mm Spring Washer 5 3 M16 x 40 x 2.00 HT Bolt Page 57 ©Design Copyright Hustler Equipment™
Floor Drive Shaft Bearing Assembly 1 Manual Parts List
Top
Bottom
5/05/2014 Section A-5 Page No. 1 Issue 5 2018
Item Number
Number =
Quantity
Number =
1 1 2 3 5 3 3 1 1 0 Item Number Quantity Part Name Manual Section Comments 1 1 Exit Side Bearing Housing 2 3 16mm Heavy Flat Washer 3 1 UCF 213-208 Bearing 4 3 16mm Spring Washer 5 3 M16 x 40 x 2.00 HT Bolt 4 3 Page 58 ©Design Copyright Hustler Equipment™
Floor Drive Shaft Bearing Assembly 2 Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
5/05/2014
Section A-6 Page No. 1 Issue 5 2018
1 1 2 4 Item Number Quantity Part Name Manual Section Comments 1 1 UCF 213-208 Housing 2 4 16mm Heavy Flat Washer 3 4 16mm Spring Washer 4 4 M16 x 40 x 2.00 HT Bolt 5 1 UCF 213-208 Bearing 3 4 4 4 5 1 Page 59 ©Design Copyright Hustler Equipment™
Floor Drive Shaft Bearing Assembly 2 Manual Parts List
5/05/2014 Section A-6 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 5 1 4 4 2 4 3 4 Item Number Quantity Part Name Manual Section Comments 1 1 FB 211 Bearing Housing Assembly 2 4 16mm Heavy Flat Washer 3 4 16mm Spring Washer 4 4 M16 x 40 x 2.00 HT Bolt 5 1 UC 211-200 Bearing Assembly Page 60 ©Design Copyright Hustler Equipment™
Floor Drive Shafts Manual Parts List
5/05/2014
A-7 Page No. 1 Issue 5 2018
Section
1 1 2 1 3 1 Item Number Quantity Part Name Manual Section Comments 1 1 Single Floor Drive Drive Shaft Assembly A-7-1 2 1 Twin Floor Drive Drive Shaft Assembly A-7-2 3 1 Twin Floor Drive Drive Shaft Assembly A-7-3 Page 61 ©Design Copyright Hustler Equipment™
Top Number = Item Number Bottom Number = Quantity
Single Floor Drive Drive Shaft Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Section A-7-1 Page No. 1
5/05/2014
Issue 5 2018
A DETAIL
3 1 2 2 4 2 5 2 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Floor Drive Shaft 2 2 0.5 x 0.5 x 90 Keysteel 3 1 1/2 x 1/2 x 65 Keysteel 4 2 5 Tooth Sprocket Assembly A-7-2-2 5 2 Floor Drive Shaft Support A-7-2-1 2 2 5 2 4 2 1 1 Page 62 ©Design Copyright Hustler Equipment™
A B DETAIL B
Twin Floor Drive Drive Shaft Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
6/05/2014
Page No.
Issue 5 2018
Section A-7-2
1
4 1 2 2 6 4
1 1 1 5 4 Item Number Quantity Part Name Manual Section Comments 1 1 Floor Drive Shaft 2 2 0.5 x 0.5 x 90 Keysteel 3 1 1/2 x 1/2 x 180 Keysteel 4 1 1/2 x 1/2 x 65 Keysteel 5 4 5 Tooth Sprocket Assembly A-7-2-2 6 4 Floor Drive Shaft Support A-7-2-1 Page 63 ©Design Copyright Hustler Equipment™
3
Floor Drive Shaft Support Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 2 assemblies per machine
Section A-7-2-1 Page No. 1 Issue 5 2018
5/05/2014
6
4 1
5 2
Item Number Quantity Part Name Manual Section Comments 1 2 M12 x 1.75 Nut 2 2 12mm Spring Washer 3 1 Drive Shaft Support Frame 4 1 1/4 Grease Nipple Straight 5 2 M12 x 40 x 1.75 HT Bolt 6 1 Drive Shaft Bush May Require Machining After Fitting 3 1 Page 64 ©Design Copyright Hustler Equipment™
1
1 2
2 2
5 Tooth Sprocket Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Issue 5 2018
Note: There are 2 assemblies per machine
Section A-7-2-2
Page No. 1
5/05/2014
2 2 Item Number Quantity Part Name Manual Section Comments 1 1 5 Tooth Cast Sprocket 2 2 3/8 x 3/8 Grubscrew Page 65 ©Design Copyright Hustler Equipment™
1 1
Floor Drive Shaft 2.5 Inch Assembly Manual Parts List 4
Top Number = Item Number
Bottom Number = Quantity
Issue 5 2018
Section A-7-3 Page No. 1
5/05/2014
1 5
3 1 1 1
Item Number Quantity Part Name Manual Section Comments 1 1 Floor Drive Shaft 2.5 Inch Drive Shaft Components 2 2 0.5 x 0.5 x 90 Keysteel 2.5 Inch Drive Shaft Components 3 1 1/2 x 1/2 x 180 Keysteel 2.5 Inch Drive Shaft Components 4 1 1/2 x 1/2 x 65 Keysteel 2.5 Inch Drive Shaft Components 5 4 5 Tooth Sprocket Assembly A-7-3-2 2.5 Inch Drive Shaft Components 6 4 Shaft Support Assembly A-7-3-1 2.5 Inch Drive Shaft Components 2 2 Page 66 ©Design Copyright Hustler Equipment™
4
6 4
Shaft Support Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 4 assemblies per machine
Section A-7-3-1 Page No. 1 Issue 5 2018
5/05/2014
4 1 5
1 2 3 1 Item Number Quantity Part Name Manual Section Comments 1 2 M12 x 1.75 Nut 2 2 12mm Spring Washer 3 1 Drive Shaft Support Frame 2.5 Inch Drive Shaft Components 4 1 1/4 Grease Nipple Straight 5 2 M12 x 40 x 1.75 HT Bolt 6 1 Drive Shaft Bush Requires Machining After Fitting 7 2 12mm Heavy Flat Washer 3 1 2 2 7 2 Page 67 ©Design Copyright Hustler Equipment™
6 1
2
5 Tooth Sprocket Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
2 2
Note: There are 4 assemblies per machine
Section A-7-3-2 Page No. 1 Issue 5 2018
5/05/2014
Item Number Quantity Part Name Manual Section Comments 1 1 5 Tooth Cast Sprocket 2.5 Inch Drive Shaft Components 2 2 3/8 x 3/8 Grubscrew 1 1 Page 68 ©Design Copyright Hustler Equipment™
5/05/2014
Issue 5 2018 Top Number = Item Number Bottom Number = Quantity Crash
3 2 2 2 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Crash Rail Frame 2 2 12mm Spring Washer 3 2 M12 x 40 x 1.75 HT Bolt Page 69 ©Design Copyright Hustler Equipment™
Section A-8 Page No. 1
Rail Assembly Manual Parts List
5/05/2014 Section A-9 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
4 2 5 1 3 1 2 2 1 1 6 1 Item Number Quantity Part Name Manual Section Comments 1 1 Floor Drive Cover Frame 2 2 12mm Flat Washer 3 1 SF 2000 Guard Sticker 4 2 4mm R Clip 5 1 Caution 1 Sticker 6 1 Guard Edging Page 70 ©Design Copyright Hustler Equipment™
Floor Drive Cover Assembly Manual Parts List
Front Panel Assembly Manual Parts List
5/05/2014
Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
Section A-10 Page No. 1
4 8 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Front Panel Frame 2 14 M12 x 25 x 1.75 HT Bolt 3 14 12mm Spring Washer 4 8 M12 x 1.75 Nut 2 14 3 14 Page 71 ©Design Copyright Hustler Equipment™
Side Panels Top Support Brace Assembly Manual Parts List
Note. This Is For A Standard Machine, Non Load Cell
5/05/2014 Section A-11 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 5 4 6 4 3 3 2 7 4 4 Item Number Quantity Part Name Manual Section Comments 1 1 Standard Side Panel Top Support Brace Frame 2 7 12mm Flat Washer 3 3 4mm R Clip 4 4 12mm Spring Washer 5 4 M12 x 1.75 Nut 6 4 M12 x 30 x 1.75 HT Bolt
Page 72 ©Design Copyright Hustler Equipment™
6/05/2014 Section A-11 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 5 4 6 4 3 3 2 7 4 4 Item Number Quantity Part Name Manual Section Comments 1 1 Load Cell Top Support Brace Frame 2 7 12mm Flat Washer 3 3 4mm R Clip 4 4 12mm Spring Washer 5 4 M12 x 1.75 Nut 6 4 M12 x 30 x 1.75 HT Bolt
Side Panels Top Support Brace Assembly Load Cell Manual Parts List
Machine Page 73 ©Design Copyright Hustler Equipment™
Note. This Is For A Load Cell
Floor Hydraulic Motor Cover Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
13/05/2014
Section A-12 Page No. 1 Issue 5 2018
4 4 2 4 3 4 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Floor Hydraulic Motor Cover Tab 2 4 M12 x 25 x 1.75 HT Bolt 3 4 12mm Spring Washer 4 4 M12 x 1.75 Nut Page 74 ©Design Copyright Hustler Equipment™
Floor Drive Chain Assembly Manual Parts List
5/05/2014
Issue 5 2018
Number = Item Number
Number = Quantity
Section A-13 Page No. 1
Top
Bottom
2 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Floor Drive Chain Frame 2 1 16B-1 Joiner Link Assembly Page 75 ©Design Copyright Hustler Equipment™
Elevator Motor Mount Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
5/05/2014 Section A-14 Page No. 1 Issue 5 2018
3 2 5 2 2 1 6 4 4 4 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Elevator Motor Mount Frame 2 1 Danfoss OMH 500 Motor 3 2 1/2 Parallel Male - 1/2 Parallel Male Nipple 4 4 12mm Spring Washer 5 2 1/2 Dowty Seal 6 4 M12 x 30 x 1.75 HT Bolt Page 76 ©Design Copyright Hustler Equipment™
Floor Pressure Relief Valve Assembly Manual Parts List
Not used on High Flow Hydraulic valves
Top
Bottom Number = Quantity
12/05/2014
Page No.
Issue 5 2018
Section A-15
1
Number = Item Number
5 1 4 1 1 1 3 2 2 2 Item Number Quantity Part Name Manual Section Comments 1 1 3 Port Pressure Relief Valve Block 2 2 M6 x 55 x 1.00 HT Bolt 3 2 M6 x 1.00 Nylock Nut 4 1 1/4 Tapered Female - 1/4 Tapered Female 90 Deg Elbow 5 1 High Pressure Back Mount Gauge 6 3 1/2 Dowty Seal 7 2 1/2 Parallel Male - 1/2 Parallel Male Nipple 8 1 1/2 Parallel Male - 1/2 Tapered Male Nipple 8 1 7 2 6 3 6 3 7 2
Page 77 ©Design Copyright Hustler Equipment™
5/05/2014 Section A-16 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity 7 1 5 1 6 1 8 6 4 6 1 1 10 1 9 1 3 3 8 6
Page 78 ©Design Copyright Hustler Equipment™
Manual Valve Block Assembly Manual Parts List
5/05/2014 Section A-16 Page No. 2 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity 7 1 5 1 6 1 8 6 4 6 1 1 10 1 3 3 2 3
Page 79 ©Design Copyright Hustler Equipment™
Manual Valve Block Assembly Manual Parts List
5/05/2014 Section A-16 Page No. 3 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity 7 1 6 1 8 6 4 6 1 1 10 1 9 1 3 3
2 3 2 3 Page 80 ©Design Copyright Hustler Equipment™
Manual Valve Block Assembly Manual Parts List
Manual Valve Block Assembly Manual Parts List
5/05/2014 Section A-16 Page No. 4 Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 1 Danfoss Manual Silage Wagon Valve 2 3 8mm Spring Washer 3 3 M8 x 20 x 1.25 HT Bolt 4 6 1/2 Dowty Seal 5 1 3/8 Parallel Male Bung 6 1 1/2 Swivel - 1/4 Taper Male Adaptor 7 1 1/2 Tapered Male Tee 8 6 1/2 Parallel Male - 1/2 Parallel Male Nipple 9 1 Internal Blanking Grubscrew 10 1 External Blanking Plug Page 81 ©Design Copyright Hustler Equipment™
Section A-17 Page No. 1
5/05/2014
5 2018 Top Number = Item Number Bottom Number = Quantity
3 2 2 2` Item Number Quantity Part Name Manual Section Comments Stock Code 2 2 8mm Spring Washer WASPM8ZP 3 2 M8 x 16 x 1.25 HT Bolt BE8X16HTZP 1 1 Valve Block Cover Tab SWCFCCMC011 1 1
Hydraulic Units Page 82 ©Design Copyright Hustler Equipment™
Issue
Valve Block Cover Assembly Manual Parts List
Not used on High Flow
5/05/2014
Issue 5 2018 Top Number = Item Number Bottom Number = Quantity Valve Block Cover Assembly Manual Parts List 3 1 2 2 1 2 Item Number Quantity Part Name Manual Section Comments Stock Code 1 2 8mm Spring Washer WASPM8ZP 2 2 M8 x 16 x 1.25 HT Bolt BE8X16HTZP 3 1 Valve Block Cover SWCCVBC-1
Section A-17 Page No. 2
Page 83 ©Design Copyright Hustler Equipment™
Only used on High Flow Hydraulic Units
Twin Floor Chain Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
2
Note: There are 2 assemblies per machine
Section A-18 Page No. 1 Issue 5 2018
5/05/2014
A DETAIL A 3 2
26
Item Number Quantity Part Name Manual Section Comments 1 2 Floor Link Chain Assembly 2 26 50 x 25 Floor Slat 3 2 Link Chain Joiner Assembly Page 84 ©Design Copyright Hustler Equipment™
1 2
Single Floor Chain Assembly Manual Parts List
13/05/2014 Section A-18 Page No. 1 Issue 5 2018
= Item Number
= Quantity 2 2 3 17 1 2 Item Number Quantity Part Name Manual Section Comments 1 2 Chain 2 2 Link Chain Joiner Assembly 3 17 25 x 50 floor slat Page 85 ©Design Copyright Hustler Equipment™
Top Number
Bottom Number
Twin Idler Shaft 1 Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
13/05/2014
Section A-19A Page No. 1 Issue 5 2018
5 1
3 2 4 1 6 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Idler Shaft Frame 2 2 Adjuster Rod Assembly 3 2 Floor Idler Sprocket Assembly A-19A-1 4 1 Inside Shaft Support Frame 1 5 1 1 1/2 Shaft Collar Assembly 6 1 Outside Shaft Support Frame 2 2 Page 86 ©Design Copyright Hustler Equipment™
2 2
Floor Idler Sprocket Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 4 assemblies per machine
Section A-19A-1 Page No. 1 Issue 5 2018
13/05/2014
1 1 2 2 3
4 1 Item Number Quantity Part Name Manual Section Comments 1 1 Cast Sprocket 2 2 X-Lube Bush 3 1 1/4 Grease Nipple Straight 4 1 Grease Point Sticker Page 87 ©Design Copyright Hustler Equipment™
1
Twin Idler Shaft 2 Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Section A-19B Page No. 1 Issue 5 2018
13/05/2014
5 1 2 2 3 2 4 1 6 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Idler Shaft Frame 2 2 Adjuster Rod Assembly 3 2 Floor Idler Sprocket Assembly A-19A-1 4 1 Inside Shaft Support Frame 2 5 1 1 1/2 Shaft Collar Assembly 6 1 Outside Shaft Support Frame 2 2 Page 88 ©Design Copyright Hustler Equipment™
Single Idler Shaft Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Section A-19C Page No. 1 Issue 5 2018
13/05/2014
2 2 3 2 7 2 1 1 5 2 6 4 4 2 Item Number Quantity Part Name Manual Section Comments 1 1 Idler Shaft 2 2 Adjuster Rod Frame 3 2 Floor Idler Sprocket Assembly A-19A-1 4 2 1 1/2 Shaft Collar Assembly 5 2 3/8 x 3/8 Grubscrew 6 4 1" UNC Nut 7 2 End Shaft Support Frame 4 2 3 2 5 2 2 2 7 2 Page 89 ©Design Copyright Hustler Equipment™
5/05/2014 Section A-20 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 7 1 5 2 4 2 2 12 6 4 Item Number Quantity Part Name Manual Section Comments 1 1 Tail Door Frame 2* 12 Large Pan Head Rivet 3 1 Tail Door Rubber Flap 4 2 M12 x 85 x 1.75 HT Bolt 5 2 M12 x 1.75 Nylock Nut 6 4 12mm Flat Washer 7 1 Cam Frame Requires engineering for replacement 3 1 Page 90 ©Design Copyright Hustler Equipment™
Tail Door Assembly Manual Parts List
Tail Door Latch Assembly Manual Parts List
Note: There are 2 assemblies per machine
Section A-21 Page No. 1 Issue 5 2018
5/05/2014
Top Number = Item Number Bottom Number = Quantity
1 1 7 1 5 1 6 1 4 1 8 2 3 1 9 1 2 2 Item Number Quantity Part Name Manual Section Comments 1 1 Latch 2 2 12mm Flat Washer 3 1 M12 x 40 x 1.75 HT Bolt 4 1 M12 x 1.75 Nylock Nut 5 1 M10 x 1.5 Nut 6 1 M10 x 30 x 1.5 HT Bolt 7 1 Spring Adjuster Frame 8 2 M12 x 1.75 Nut 9 1 Tramp Spring Page 91 ©Design Copyright Hustler Equipment™
Elevator Motor Retainer Plate Assembly Manual Parts List
Note: There are 2 assemblies per machine
A-22
1
5/05/2014
Item Number
= Quantity
Section
Page No.
Issue 5 2018 Top Number =
Bottom Number
5 3 3 2 6 1 2 3 1 3 4 1 Item Number Quantity Part Name Manual Section Comments 1 3 12mm Spring Washer 2 3 12mm Flat Washer 3 2 M12 x 40 x 1.75 Coach Bolt 4 1 Elevator Motor Retainer Plate Frame 5 3 M12 x 1.75 Nut 6 1 M12 x 40 x 1.75 HT Bolt Page 92 ©Design Copyright Hustler Equipment™
Floor Reduction Drive Assembly Manual RE45
6/05/2014 Section A-23 Page No. 1 Issue 5 2018 15 1 5 1 4 1 7 1 8 1 10 1 11 1 6 1 13 2 14 1 1 2 9 3 3 3 12 1
Top Number = Item Number
Bottom Number = Quantity
Page 93 ©Design Copyright Hustler Equipment™
Top Number = Item Number
Bottom Number = Quantity
6/05/2014 Section A-23 Page No. 2 Issue 5 2018 Floor Reduction Drive Assembly Manual RE45 5 1 4 1 7 1 8 1 10 1 11 1 6 1 13 2 14 1 9 3 3 3 18 1
9 3 2 4 1 2 15 1 16 1 Page 94 ©Design Copyright Hustler Equipment™
Floor Reduction Drive Assembly Manual RE45 Parts List
Section A-23 Page No. 3 Issue 5 2018
6/05/2014
Item Number Quantity Part Name Manual Section Comments 1 2 M12 x 1.75 Nylock Nut 2 4 12mm Heavy Flat Washer 3 3 M8 x 65 x 1.25 HT Bolt 4 1 Idler 2 Assembly A-23-2 5 1 Idler 1 Assembly A-23-2 6 1 Reduction Mounting Plate Frame Assembly 7 1 No 1 Sprocket Reduction Assembly 8 1 No 2 Reduction Assembly 9 3 M8 x 1.25 Nylock Nut 10 1 No 1 Reduction Chain Assembly A-23-3 11 1 No 2 Reduction Chain Assembly A-23-3 12 1 Tramp Spring 13 2 Reduction Shaft Assembly A-23-4 14 1 Shaft Support 15 1 RE45 Hydraulic Motor Assembly A-23-1 16 1 Stablizer Shaft Page 95 ©Design Copyright Hustler Equipment™
RE45 Hydraulic Motor Assembly Manual Parts List
For 1750 & 2000 Side Feed Silage Wagon
5/05/2014
Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
Section A-23-1 Page No. 1
2 1 3 2 4 2 5 2 1 1 7 2 6 2 Item Number Quantity Part Name Manual Section Comments 1 1 RE 45 White Hydraulic Motor 2 1 15 Tooth x 0.75 Pitch x 1.25 Bore 3 2 3/8" x 3/4" Grubscrew 4 2 1/2 Parallel Male - 1/2 Parallel Male Nipple 5 2 1/2 Dowty Seal 6 2 12mm Spring Washer 7 2 M12 x 35 x 1.75 HT Bolt Page 96 ©Design Copyright Hustler Equipment™
Danfoss
500 Hydraulic Motor
Assembly Manual Parts List For 1250 & 1500 Side Feed Silage Wagon
Top Number = Item Number
Bottom Number = Quantity
Section A-23-1 Page No. 1 Issue 5 2018
5/05/2014
2 1 3 2 4 2 7 2 1 1 6 4 5 4 Item Number Quantity Part Name Manual Section Comments 1 1 Danfoss OMH 500 Motor 2 1 15 Tooth x 0.75 Pitch x 35mm Bore 3 2 3/8" x 3/4" Grubscrew 4 2 1/2 Parallel Male - 1/2 Parallel Male Nipple 5 4 12mm Spring Washer 6 4 M12 x 35 x 1.75 HT Bolt 7 2 1/2 Dowty Seal Page 97 ©Design Copyright Hustler Equipment™
Danfoss OMH 315 Hydraulic Motor Assembly Manual Parts List
All Models with the High Flow Hydraulic valve will use this motor configuration.
Top Number = Item Code
Bottom Number = Item Number
Section A-23-1 Page No. 1
13/05/2014 Issue 5 2018
5 2 2 2 1 2 6 1 7 4 3 4 4 1 Item Number Quantity Part Name Manual Section Comments Stock Code 1 2 1/2 Dowty Seal HYDD-08 2 2 1/2 Parallel Male - 1/2 Parallel Male Nipple HYDB-B-0808 3 4 12mm Spring Washer WASPM12ZP 4 1 15 Tooth x 0.75 Pitch x 35mm Bore SP15TOOTH12B-1 5 2 3/8 x 3/4 Grubscrew BEG/SCREW3/8X3/4 6 1 Danfoss OMH 315 Hydraulic Motor Danfoss 7 4 M12 x 35 x 1.75 HT Bolt BE12X35HTZP
Page 98 ©Design Copyright Hustler Equipment™
Idler Assembly Manual Parts List
Top Number = Item Number Bottom Number = Quantity Note: There are 2 assemblies per machine
Issue 5 2018
Section A-23-2 Page No. 1
5/05/2014
8 1 6 1 7 1 1 1 2 1 4 1 5 4 9 1 3 1 Item Number Quantity Part Name Manual Section Comments 1 1 M12 x 1.75 Nylock Nut 2 1 M12 x 1.75 Nut 3 1 12mm Spring Washer 4 1 M12 x 60 x 1.75 HT Bolt 5 4 12mm Flat Washer 6 1 12 Tooth 1" Plate Sprocket 7 1 6201 Bearing 8 1 Idler Arm 2 9 1 12mm Heavy Flat Washer Page 99 ©Design Copyright Hustler Equipment™
Top Number = Item Number
Bottom Number = Quantity
Reduction Chain Assembly Manual Parts List 1
Issue 5 2018
Note: There are 2 assemblies per machine
Section A-23-3 Page No. 1
5/05/2014
2 1 Item Number Quantity Part Name Manual Section Comments 1 1 No 1 Reduction Chain Frame 2 1 RC 60 HV Chain Joiner Page 100 ©Design Copyright Hustler Equipment™
1
Reduction Shaft Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 2 assemblies per machine
Section A-23-4 Page No. 1 Issue5 2018
5/05/2014
1 1 2 1 Item Number Quantity Part Name Manual Section Comments 1 1 Reduction Shaft 2 1 1/8 BSPT Grease Nipple Straight Page 101 ©Design Copyright Hustler Equipment™
Page 102 ©Design Copyright Hustler Equipment™
Top Bolster Rail Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Issue 5 2018
Note: There are 4 assemblies per machine
Section A-24 Page No. 1
5/05/2014
1 1 4 3 2 3 Item Number Quantity Part Name Manual Section Comments 1 1 Top Bolster Rail 2 3 M12 x 80 x 1.75 Coach Bolt 3 3 12mm Spring Washer 4 3 M12 x 1.75 Nut 3 3 Page 103 ©Design Copyright Hustler Equipment™
12/05/2014 Section A-25 Page No. 1 Issue 5 2018
Number = Item Number Bottom Number = Quantity
Cell Head Unit Mount Assembly Manual 4 1 1 1 12 1 11 1 10 1 3 1 7 1 5 8 A DETAIL A 8 4 Revision Number 6 8 2 4 9 1 Page 104 ©Design Copyright Hustler Equipment™
Top
Load
Load Cell Head Unit Mount Assembly Manual Parts List
12/05/2014
Item Number Quantity Part Name Manual Section Comments 1 1 Load Cell Head Unit Mount Frame 2 4 6mm Panel Washer 3 1 M12 x 1.75 Nylock Nut 4 1 Latch Assembly Frame 5 8 M6 x 20 x 1.00 HT Bolt 6 8 6mm Spring Washer 7 1 M12 x 60 x 1.75 HT Bolt 8 4 M6 x 1.00 Nut 9 1 Stad 04 Modified Head Unit Rev-002 Assembly 10 1 Load Cell Head Unit Cover Assembly A-25-1 11 1 Silage Wagon Load Cell Sensor Cable Rev 002 Assembly Note Revision No. 12 1 Silage Wagon Load Cell Power Cable Assembly Note Revision No.
Section A-25 Page No. 2 Issue 5 2018
Page 105 ©Design Copyright Hustler Equipment™
Load Cell Head Unit Cover Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
13/05/2014 Issue 5 2018 Page No. 1
A-25-1
Section
1 2 2 1 3 1 4 10 5 10 Item Number Quantity Part Name Manual Section Comments Stock Code 1 2 63.5mm x 25mm x 1mm Flush Mount Hinge MIHINGE2 2 1 Lexon Cover MILCOVER1MM 3 1 Load Cell Head Unit Cover Tab STOCK-LC-001 4 10 M4 x 0.7 Nut BEHEXM4ZP 5 10 M4 x 12 x 0.7 Pan Head Bolt BE4X12CSSCREWSS Page 106 ©Design Copyright Hustler Equipment™
13/05/2014 Section A-26 Page No. 1 Issue 5 2018
Number = Item Number
Number = Quantity
Top
Manual Parts List 1 1 4 6 2 6 3 6 Item Number Quantity Part Name Manual Section Comments 1 1 Load Cell Drawbar Top Cover Frame 2 6 8mm Flat Washer 3 6 8mm Spring Washer 4 6 M8 x 20 x 1.25 HT Bolt Page 107 ©Design Copyright Hustler Equipment™
Top
Bottom
Load Cell Drawbar
Cover Assembly
Page 108 ©Design Copyright Hustler Equipment™
Load Cell Drawbar Lower Cover Assembly Manual Parts List
13/05/2014
Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
Section A-27 Page No. 1
1 1 3 6 4 6 2 6 Item Number Quantity Part Name Manual Section Comments 1 1 Load Cell Drawbar Lower Cover Frame 2 6 8mm Flat Washer 3 6 M8 x 1.25 Nylock Nut 4 6 M8 x 25 x 1.25 HT Bolt Page 109 ©Design Copyright Hustler Equipment™
Load Cell Towing 50mm Bolt On Assembly Manual
13/05/2014 Section A-28 Page No. 1 Issue 5 2018
Top Number = Item Number Bottom Number = Quantity 2 1 1 1 15 2 19 2 14 1 16 2 18 3 4 3 3 2 13 4 11 4 6 4 10 4 22 1 5 4 12 18 8 4 23 1 21 1 9 10 7 1 8 20 Page 110 ©Design Copyright Hustler Equipment™
Load Cell Towing 50mm Bolt On Assembly Manual
Parts List
13/05/2014 Section A-28 Page No. 2 Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 1 Cat 1 Lower Link Pin 2 1 AG 3 Linch Pin 12 mm 3 2 M16 x 45 x 2.00 HT Bolt 4 3 M12 x 35 x 1.75 HT Bolt 5 4 16mm Flat Washer 6 4 M20 x 2.50 Nut 7 1 40mm Bolt On Draw Bar Tounge 8 4 20mm Spring Washer 9 10 M16 x 2.00 Nut 10 4 M20 x 90 x 2.50 HT Bolt 11 4 M18 x 2.5 Nylock Nut 12 18 16mm Spring Washer 13 4 M18 x 100 x 2.5 HT Bolt 14 1 Towing Eye Bolt On Frame 15 2 27mm Long Load Cell Casting 16 2 54mm Load Cell Bar Rev 002 17* 8 M16 x 40 x 2.00 HT Bolt 18 3 M12 x 1.75 Nut 19 2 35mm Long Load Cell Casting 20 8 M16 x 60 x 2.00 HT Bolt 21 1 7 Pin Plug Holder Assembly A-28-1 22 1 Robertson Jack Assembly A-28-2 23 1 Safety Chain 13mm Assembly A-28-3 Page 111 ©Design Copyright Hustler Equipment™
13/05/2014 Section A-28 Page No. 1 Issue 5 2018 Load Cell Towing 40mm Weld On
Manual
Number = Item Number Bottom Number = Quantity 6 1 5 1 12 2 11 1 11 1 15 2 1 3 2 3 14 10 13 2 8 2 10 4 18 1 7 4 9 4 19 1 17 1 3 8 4 8 Page 112 ©Design Copyright Hustler Equipment™
Assembly
Top
Load Cell Towing 40mm Weld On Assembly Manual Parts List
13/05/2014 Section A-28 Page No. 2 Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 3 M12 x 1.75 Nut 2 3 M12 x 35 x 1.75 HT Bolt 3 8 M16 x 60 x 2.00 HT Bolt 4 8 M16 x 40 x 2.00 HT Bolt 5 1 Cat 1 Lower Link Pin 6 1 AG 3 Linch Pin 12 mm 7 4 16mm Flat Washer 8 2 M16 x 45 x 2.00 HT Bolt 9 4 M18 x 100 x 2.5 HT Bolt 10 4 M18 x 2.5 Nylock Nut 11 1 Towing eye Frame Assembly 12 2 27mm Long Load Cell Casting 13 2 35mm Long Load Cell Casting 14 10 M16 x 2.00 Nut 15 2 54mm Load Cell Bar Rev 002 16* 18 16mm Spring Washer 17 1 7 Pin Plug Holder Assembly A-28-1 18 1 Robertson Jack Assembly A-28-2 19 1 Safety Chain 13mm Assembly A-28-3 Page 113 ©Design Copyright Hustler Equipment™
6 Cell Junction Box Cover Assembly Manual Parts List
13/05/2014 Section A-29 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
1 1 4 2 2 2 3 2 Item Number Quantity Part Name Manual Section Comments 1 1 6 Cell Junction Box Cover Tab 2 2 8mm Flat Washer 3 2 8mm Spring Washer 4 2 M8 x 25 x 1.25 HT Bolt 5 1 Load Cell Junction Box Rev-002 Assembly A-29-1 5 1 Page 114 ©Design Copyright Hustler Equipment™
Super Comby Load Cell Junction Box Rev-002 Assembly Manual
13/05/2014 Section A-29-1 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
2 5 3 1 4 1 5 4 6 4 7 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 100mm x 40mm Robertson Sticker 2 5 12mm Grommett 3 1 Circurt Board Rev 002 Assemby 4 1 Junction Box Assembly 5 4 M3 x 6 x 0.5 Pan Head Stainless Bolt 6 4 M4 x 12 x 0.70 Capscrew 7 1 Silca Gel Bag 100 GSM Note Revision Number On Board Page 115 ©Design Copyright Hustler Equipment™
Parts List
13/05/2014
A-30 Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity Battery Box Incl Battery Manual Parts List 2 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Battery Box Includes Lid & Tie Strap 2 1 12 Volt Battery 1 1 Page 116 ©Design Copyright Hustler Equipment™
Section
Spec's Chassis Tag Assembly Manual Parts List
Section A-31 Page No. 1
13/05/2014
5 2018
Issue
Top Number = Item Number Bottom Number = Quantity
2 1 1 4 Item Number Quantity Part Name Manual Section Comments Stock Code 1 4 4mm Rivet RI73AS55-5 2 1 Spec's Chassis Tag mitareplate Page 117 ©Design Copyright Hustler Equipment™
Page 118 ©Design Copyright Hustler Equipment™
Mudguard 405-70-R18 Wheel Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Issue 5 2018
Note: There are 2 assemblies per machine
Section A-32 Page No. 1
5/05/2014
Item Number Quantity Part Name Manual Section Comments 1 1 Mudguard 405-70-R18 Wheel Frame 2 4 12mm Heavy Flat Washer 3 6 12mm Spring Washer 4 2 M12 x 30 x 1.75 HT Bolt 5 2 M12 x 80 x 1.75 HT Bolt 6 2 M12 x 1.75 Nut A
2 4 3 6 5 2 6 2 3 6 4 2 Page 119 ©Design Copyright Hustler Equipment™
1 1
DETAIL A
X-Conveyor Belt & Chain Assembly Manual
Parts List
Top Number = Item Code
Bottom Number = Item Number
13/05/2014
5 2018
Issue
Section B-1 Page No. 1
Belt Conveyor
Page 120 ©Design Copyright Hustler Equipment™
Chain Conveyor
13/05/2014 B-2 Page No. 1 Issue 5 2018 X-Conveyor Assembly Manual - Rev 02 Page 121 ©Design Copyright Hustler Equipment™
X-Conveyor Assembly Manual - Rev 02
13/05/2014
Page No. 2 Issue 5 2018 5 4 3 1 6 1
B-2
Top Number = Item Number
1 1 4 1 8 1 9 1 11 1 2 1
used on Chain Units
used on Chain Units
used on Chain Units Only used on Chain Units Page 122 ©Design Copyright Hustler Equipment™
Bottom Number = Quantity
Only
Only
Only
X-Conveyor Assembly Manual - Rev 02 Parts List
13/05/2014
B-2 Page No. 3 Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 1 Bolt On Discharge Assembly - Rev 01 B-2-1 Only on chain drive 2 1 Conveyor Chain Assembly B-2-2 Only on chain drive 3 1 Drive Flap Cover 4 1 Front Idler Mount Assembly B-3.3 5 4 Large Pan Head Rivet 6 1 Motor Drive Assembly B-2-3 Use OMH 315 7* 1 Non Tracked Belt Assemby Only on belt drive 8 1 Roller Chain Drive Shaft Assembly B-2-4 Only on chain drive 9 1 Roller Chain Idler Shaft Assembly B-2-5 Only on chain drive 10* 2 Rubber Flap Assembly B-3-5 Only on belt drive 11 1 X-Conveyor Frame - Rev 02 Only on Chain drive Page 123 ©Design Copyright Hustler Equipment™
Bolt On Discharge Assembly Manual - Rev 01 Parts List
Top Number = Item Number
Bottom Number = Quantity
Section B-2-1 Page No. 1
6/05/2014
Issue 5 2018
Item Number Quantity Part Name Manual Section Comments Stock Code 1 7 12mm Spring Washer WASPM12ZP 2 1 Bolt On Discharge Frame - Rev 01 3 7 M12 x 1.75 Nut BEHEXM12ZP 4 4 M12 x 40 x 1.75 HT Bolt BE12X40HTZP 3 7 4 4 1 7 2 1 Page 124 ©Design Copyright Hustler Equipment™
Conveyor Chain Assembly Manual Parts List
Section B-2-2 Page No. 1
Top Number = Item Code
Bottom Number = Item Number
13/05/2014
5
Issue
2018
1 2 2 1 Item Number Quantity Part Name Manual Section Comments Stock Code 1 2 3 Inch Roller Chain Joiner Link CH3JOINER 2 1 Conveyer Chain Frame Page 125 ©Design Copyright Hustler Equipment™
Motor Drive Assembly Manual Parts List
Motor changed to a OMP200 when used with a Chain and Bar conveyer OMP 125 when used with a Belt Conveyer
Top Number = Item Number
Bottom Number = Quantity
B-2-3 Page No. 1
6/05/2014
Issue 5 2018
4 2 1 6 2 4 2 5 2 7 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Motor Mount 2 1 Danfoss OMP 125 HYD Motor 3 4 3/8 x 3/8 Grubscrew 4 2 M12 x 40 x 1.75 HT Bolt 5 2 12mm Spring Washer 6 2 M12 x 1.75 Nut 7 1 Motor Coupling Frame 8 2 1/2 Parallel Male - 1/2 Parallel Male Nipple 9 2 1/2 Dowty Seal 8 2 9 2
3
Page 126 ©Design Copyright Hustler Equipment™
Roller Chain Drive Shaft Assembly Manual Parts List
Section B-2-4 Page No. 1
13/05/2014
5 2018
Issue
Top Number = Item Code Bottom Number = Item Number 3 2 4 1 9 1 6 4 7 2 1 4 2 4 8 1 5 1 10 1 Item Number Quantity Part Name Manual Section Comments Stock Code 1 4 12mm Flat Washer WAM12FLAT WASHER 2 4 12mm Spring Washer WASPM12ZP 3 2 208-108 Bearing Assembly BRGUC208-24 4 1 208-108 Housing Assembly BRGF208C 5 1 3/8 x 3/8 x 100mm Keysteel STKEY3/8X3/8 6 4 M12 x 30 x 1.75 HT Bolt BE12X30ZPHT 7 2 M20 x 2.50 Nut BEHEXM20ZPNUT 8 1 Roller Chain Drive Shaft Frame 9 1 YAR 208 Housing Assembly BRGT208 10 1 Roller Adjuster B-3-6 Page 127 ©Design Copyright Hustler Equipment™
Roller Chain Idler Shaft Assembly Manual Parts List
13/05/2014 Issue 5 2018
Section B-2-5 Page No. 1
Top Number = Item Code Bottom Number = Item Number 1 2 4 2 2 4 3 1 5 2 Item Number Quantity Part Name Manual Section Comments Stock Code 1 2 208-108 Bearing Assembly BRGUC208-24 2 4 M20 x 2.50 Nut BEHEXM20ZPNUT 3 1 Roller Chain Idler Shaft Frame 4 2 YAR 208 Housing Assembly BRGT208 5 2 Roller Adjuster B-3-6 Page 128 ©Design Copyright Hustler Equipment™
6/05/2014 B-3 Page No. 1 Issue 5 2018
Page 129 ©Design Copyright Hustler Equipment™
X-Conveyor Assembly Manual
X-Conveyor Assembly Manual
Top Number = Item Number
Bottom Number = Quantity
6/05/2014 B-3 Page No. 2 Issue 5 2018 7 4 8 1 4 2 9 1 2 1 5 1 11 1 6 1 1 1
10 1 Page 130 ©Design Copyright Hustler Equipment™
X-Conveyor Assembly Manual Parts List
6/05/2014
B-3 Page No. 3 Issue 5 2018
Item Number Quantity Part Name Manual Section Comments 1 1 X-Conveyor Frame 2 1 Front Idler Mount Assembly B-3-3 4 2 Rubber Flap Assembly B-3-5 5 1 Motor Drive Assembly B-2-3 6 1 Idler Roller Assembly B-3-4 7 4 Large Pan Head Rivet 8 1 Non Tracked Belt Assemby 9 1 Drive Flap Cover 10 1 Bolt On Discharge Assembly B-3-1 11 1 Drive Roller Assembly B-3-2 Page 131 ©Design Copyright Hustler Equipment™
Bolt On Discharge Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
5/05/2014
5
Section B-3-1 Page No. 1 Issue
2018
7 3 7 1 7 2 1 Item Number Quantity Part Name Manual Section Comments 1 7 12mm Spring Washer 2 1 Bolt On Discharge Frame 3 7 M12 x 40 x 1.75 HT Bolt 4 7 M12 x 1.75 Nut Page 132 ©Design Copyright Hustler Equipment™
4
Drive Roller Assembly Manual Parts List
13/05/2014
Page No. 1 Issue 5 2018 Top Number = Item Number Bottom Number = Quantity
B-3-2
3 2 4 1 8 1 10 4 9 2 5 4 7 4 2 1 6 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Roller Frame 2 1 3/8 x 3/8 x 100mm Keysteel 3 2 208-108 Bearing Assembly 4 1 208-108 Housing Assembly 5 4 12mm Flat Washer 6 1 Roller Adjuster B-3-6 7 4 12mm Spring Washer 8 1 YAR 208 Housing Assembly 9 2 M20 x 2.50 Nut 10 4 M12 x 30 x 1.75 HT Bolt Page 133 ©Design Copyright Hustler Equipment™
Front Idler Mount Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
6/05/2014
B-3-3 Page No. 1 Issue 5 2018
6 3 3 7 4 4 5 3 2 1 Item Number Quantity Part Name Manual Section Comments 1* 1 Front Idler Mount Frame 2 1 Flap Cover 3 7 M10 x 30 x 1.5 HT Bolt 4 4 Large Pan Head Rivet 5 3 10mm Spring Washer 6 3 M10 x 1.5 Nut Page 134 ©Design Copyright Hustler Equipment™
Idler Roller Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
13/05/2014
5
B-3-4 Page No. 1 Issue
2018
2 2 3 2 4 4 5 2 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Idler Roller Frame 2 2 208-108 Bearing Assembly 3 2 YAR 208 Housing Assembly 4 4 M20 x 2.50 Nut 5 2 Roller Adjuster B-3-6 Page 135 ©Design Copyright Hustler Equipment™
Rubber Flap Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 2 assemblies per machine
B-3-5 Page No. 1
6/05/2014
5
Issue
2018
1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Flap 2 10 Large Pan Head Rivet Page 136 ©Design Copyright Hustler Equipment™
2 10
Roller Adjuster Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 3 assemblies per machine
B-3-6 Page No. 1
6/05/2014
5
Issue
2018
3 1 1 1 2 1 Item Number Quantity Part Name Manual Section Comments 1 1 M20 Threaded Rod 2 1 Stop Flat 3 1 1/4" x 1 3/4 Roll Pin Page 137 ©Design Copyright Hustler Equipment™
Axle Assembly 405-70-R18 Heavy Duty Assembly Load Cell Manual
Parts List
Top Number = Item Number Bottom Number = Quantity
5/05/2014
Section C-1 Page No. 2 Issue 5 2018
5 2 4 2 3 4 2 4 1 1 6 4 Item Number Quantity Part Name Manual Section Comments 1 1 Axle Frame Load Cell Axle Assembly 405-70-R18 Heavy Duty Assembly 2 4 405x70xR18 Traction Wheel Assembly 3 4 Grease Point Sticker 4 2 1/4 Grease Nipple 90 Deg 5 2 1/4 Grease Nipple Straight 6 4 Load Cell Mount Assembly 7 4 Page 138 ©Design Copyright Hustler Equipment™
5/05/2014 Section C-1 Page No. 1 Issue 5 2018 Axle Assembly 405-70-R18 Heavy
Standard Manual Parts
5 2 4 2 7 4 6 4 3 4 2 4 1 1 Top Number = Item Number Bottom Number = Quantity 9 4 8 4 Item Number Quantity Part Name Manual Section Comments 1 1 Axle Frame Standard 2 4 405x70xR18 Traction Wheel Assembly 3 4 Grease Point Sticker 4 2 1/4 Grease Nipple 90 Deg 5 2 1/4 Grease Nipple Straight 6 4 M20 x 65 x 2.50 HT Bolt 7 4 M20 x 2.50 Nut 8 4 20mm Spring Washer Page 139 ©Design Copyright Hustler Equipment™
Duty Assembly
List
405x70xR18 Wheel Assembly Manual Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: When ordering tyres please quote tread pattern TRAC Tread
Issue 5 2018
Note: There are 4 assemblies per machine
C-2 Page No. 1
6/05/2014
1 1 2 1 Item Number Quantity Part Name Manual Section Comments 1 1 13 x 18 x 8 Stud Rim Assembly 2 1 405x70xR18 Traction Tyre Page 140 ©Design Copyright Hustler Equipment™
5/05/2014
Issue 5 2018
Top Number = Item Number Bottom Number = Quantity 2 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 9 x 80 x 6 Stud Rim Assembly 2 1 11.5 x 80 x 15.3 AW Tyre Page 141 ©Design Copyright Hustler Equipment™
Section C-2 Page No. 1
11.5 x 80 x 15.3 Wheel Assembly Manual Parts List
400 x 60 x 15.5
Wheel Assembly Manual Parts List
Note: When ordering tyres please quote tread pattern
13/05/2014 Section C-2 Page No. 1 Issue 5 2018
Bottom
=
Top Number = Item Number
Number
Quantity
TRAC Tread 1 1 2 1 Item Number Quantity Part Name Manual Section Comments 1 1 60 x 15.5 Rim Assembly 2 1 400x60x15.5 AW Tyre AW Tread Page 142 ©Design Copyright Hustler Equipment™
70mm x 70mm Unbraked Hub & Stub Assembly Manual
Note: There are 4 assemblies per machine
Section C-3 Page No. 1
13/05/2014
5
Item
Quantity
Issue
2018 Top Number =
Number Bottom Number =
List 10 1 4 1 13 1 1 1 2 1 3 1 7 1 9 1 12 1 11 1 6 6 5 6 8 1 Item Number Quantity Part Name Manual Section Comments 1 1 70 x 70 Hub 2 1 30210 Small Wheel Bearing 3 1 30213 Large Wheel Bearing 4 1 90mm Dust Cap 5 6 M18 x 50 Wheel Stud 6 6 M18 Wheel Nut 7 1 Stub Split Pin 8 1 Grease Point Sticker 9 1 Stub Nut 10 1 70 x 70 Stub 11 1 70 x 70 Stub Seal 12 1 Stub Seal Carrier 13 1 1/4 Grease Nipple Straight Page 143 ©Design Copyright Hustler Equipment™
Parts
70mm x 70mm Braked Hub & Stub Assembly Manual Parts List
Issue 5 2018
Note: There are 2 assemblies per machine
Section C-3 Page No. 1
13/05/2014
Top Number = Item Number Bottom Number = Quantity
5 1 6 1 2 1 10 1 9 1 4 1 13 1 11 1 7 6 8 6 Item Number Quantity Part Name Manual Section Comments 1 1 6mm Grease Nipple Straight 2 1 70 x 70 Stub 3 1 70 x 70 Stub Seal 4 1 80 mm Dust Cap 5 1 Brake Arm 6 1 Brake Drum 7 6 M18 Wheel Nut 8 6 M18 x 50 Wheel Stud 9 1 SKF 30210 Small Wheel Bearing 10 1 SKF 30213 Large Wheel Bearing 11 1 Stub Nut 12 1 Stub Seal Carrier 13 1 Stub Split Pin 3 1 12 1 1 1 Page 144 ©Design Copyright Hustler Equipment™
80mm x 80mm x 8 Stud
Unbraked FAD Stub Assembly Manual
Parts List
Top Number = Item Number
Bottom Number = Quantity
Note: There are 2 assemblies per machine
Issue 5 2018
C-3 Page No. 1
6/05/2014
9 1 1 8 10 1 11 1 7 1 Item Number Quantity Part Name Manual Section Comments 1 8 M18 x 50mm x 1.5mm Wheel Stud c/w stub 2 8 M18 x 1.5mm Wheel Nut c/w stub 7 1 75mm x 130mm x 33.25 32215 Single Row Bearing Assembly 9 1 80mm x 80mm Stub 10 1 Stub Nut Retainer Clip 11 1 Stub Nut 13 1 Hub 8 Stud 14 1 Shoulder Ring 15 1 90x130x12 Oil Seal 16 1 55mm x 100mm x 29.45 32211 Single Row Bearing Assembly 17 1 Dust Cap 18 1 1/8 BSPT 90 deg Grease Nipple 14 1 13 1 2 8 16 1 11 1 17 1 15 1 18 1
Page 145 ©Design Copyright Hustler Equipment™
Load Cell Axle Mount Assembly Manual Parts List
Note: There are 4 assemblies per machine
6/05/2014
C-4 Page No. 1 Issue 5 2018
Top Number = Item Number Bottom Number = Quantity
3 1 14 8 12 8 5 1 7 1 6 2 11 2 8 1 9 1 13 8 10 2 4 1 2 1 1 1 Item Number Quantity Part Name Manual Section Comments 1 1 Axle Mount Adaptor Plate 2 1 32mm End Load Cell Casting 3 1 54mm Load Cell Bar Rev 002 4 1 32mm End Load Cell Casting 5 1 M18 x 100 x 2.5 HT Bolt 6 2 M18 x 2.5 Nylock Nut 7 1 M18 x 140 x 2.00 HT Bolt 8 1 M20 x 50 x 2.50 HT Bolt 9 1 M20 x 65 x 2.50 HT Bolt 10 2 20mm Spring Washer 11 2 M20 x 2.50 Nut 12 8 M16 x 65 x 2.00 HT Bolt 13 8 16mm Spring Washer 14 8 M16 x 2.00 Nut Page 146 ©Design Copyright Hustler Equipment™
13/05/2014 Section D-Amendments Page No. 1 Issue 5 2018 AMENDMENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Page 147 ©Design Copyright Hustler Equipment™
13/05/2014 Section D-Amendments Page No. 2 Issue 5 2018
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Page 148 ©Design Copyright Hustler Equipment™
NOTES
Please complete this form, remove and return to dealer
Dealer Copy
MODEL ..........................................................................................................
SERIAL NUMBER ..........................................................................................................
OWNER ADDRESS
.......................................................................................................... ......................................................................................................... ……………………………………………………………………
TELEPHONE NUMBER ..........................................................................................................
FAX NUMBER
E-MAIL ..........................................................................................................
DELIVERY DATE
DEALER NAME
DEALER
TELEPHONE NUMBER ..........................................................................................................
DECLARATION I declare that I have read this manual and understand the Warnings and Cautions Owner Signature............................................................Date………………..
Pre delivery check completed .................(initial) Dealer Signature................................................Date.........................
Issue 5 2018
Section D-Amendments Page No. 3
13/05/2014
Page 149
Copyright Hustler Equipment™
©Design
Page 150 ©Design Copyright Hustler Equipment™
Please complete this form, fold along the dotted lines on the reverse of this page, tape the edge, affix a stamp and post
Hustler's Copy
MODEL ..........................................................................................................
SERIAL NUMBER ..........................................................................................................
OWNER ADDRESS
.......................................................................................................... ......................................................................................................... ……………………………………………………………………
TELEPHONE NUMBER ..........................................................................................................
FAX NUMBER
E-MAIL ..........................................................................................................
DELIVERY DATE
DEALER NAME
DEALER TELEPHONE NUMBER ..........................................................................................................
DECLARATION
I declare that I have read this manual and understand the Warnings and Cautions Owner Signature............................................................Date……………….. Pre delivery check completed .................(initial)
Dealer Signature................................................Date.........................
13/05/2014
Section D-Amendments Page No. 4 Issue 5 2018
Page 151 ©Design Copyright Hustler Equipment™
13/05/2014 Section D-Amendments Page No. 5 Issue 5 2018 FOLD HERE FOLD HERE POST TO.... Hustler Equipment Int. PO Box 2127 Stortford Lodge Hastings 4153 New Zealand AFFIX STAMP HERE Page 152 ©Design Copyright Hustler Equipment™
Pre Delivery Check Sheet for Robertson Feed Out Wagons
Machine Options Fitted as Requested
Axle Bolts Checked
Breather Ports Lubricated on Lift Rams
All Points Greased
All Floor Chain Joiners Fitted and Tensioned Correctly
Floor Chains Engaged with Sprockets Correctly
Check Elevator Shaft Cover is Adjusted Correctly
All Hydraulic Hoses and Fittings, Tight and Checked for Leaks
Electric/Manual Controls Working
Jack Operation Correct
'R' Clip installed on Covers
All Joints Sealed
All Stickers Attached and Undamaged
Operators Manual Supplied
Reflectors
NZ Patent
Aussie Patent
Paint Job OK Test Run OK
Machine Runs Correctly
Machine Quiet in Operation
Lights Working - if fitted
Brakes Working and Adjusted Correctly - if fitted
Load Cell Weighing System, Calibrated and Weighing Correctly - if fitted
SILAGE WAGON RANGE
Cross Conveyer Belt Tracking Correct
Electric/Manual Floor Speed Controller Operational
COMBY RANGE
Safety Bolts (x2) Removed from Tilt Elevator - if Tilt Option Fitted
Electric/Manual Direction & Accessory Controls Operational
MEGA COMBY
Safety Bolts (x2) Removed from Tilt Elevator - if Tilt Option Fitted
Tilt Elevator Smooth and Correct Operation
Flap Sensor adjusted and Operational
(Check Bed Floor is Disabled when Elevator is Fully Up.)
Pin Captivators are Fitted Correctly - If Forks Fitted
Date……………………………………
Print Name Signed
Dealer Name
Comments:-
Serial Number………………………………
This form must be completed and returned with 30 days of inspection, Fax to Robertson Manufacturing Ltd to Validate Warrenty.
Section D-Amendments Page No. 6 Issue 5 2018
13/05/2014
Safety
Bolts Fitted All Wheel Nuts Checked OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK Page 153 ©Design Copyright Hustler Equipment™
All Nuts and Bolts Checked Tyre Pressures Correct
Chain Retainer
13/05/2014 Section D-Amendments Page No. 5 Issue 5 2018 FOLD HERE FOLD HERE POST TO.... Hustler Equipment Int. PO Box 2127 Stortford Lodge Hastings New Zealand AFFIX STAMP HERE Page 154 ©Design Copyright Hustler Equipment™