iPhone速 6 Repair Flowchart
Back Up Your Device Repairing a device comes with the risk of damaging important components and losing data. Before repairing, securely back up your device. Back Up Via iTunes Connect your device to your computer and open iTunes. Select your device in the upper right corner and select Back Up Now in the Backups Window. Back Up Via iCloud Make sure you are connected to the Internet via WiFi. Go to Settings>iCloud>Storage & Backup. Switch iCloud Backup to ON and tap Back Up Now.
Tools Needed
#00 Phillips Screwdriver
Suction Cup 2
Pentalobe Screwdriver
Spudger or Pry Tool
iPhone 6 Screen Replacement
Heat Tool
Watch the Video Before you begin, watch our online repair video. Visit our YouTube channel and find your device. www.YouTube.com/iCrackediPhoneRepair
Important Tips Take Your Time Allow 1-2 hours for this repair and be patient. Most mistakes are caused by rushing through the steps. Be Gentle Remember that you are handling fragile hardware. Stay Organized Note the placement of screws and small parts as you disassemble the device. Keep screws and small parts from each step in separate, small compartments or containers, like drink caps, or laid out on a clean flat surface. Use a paperweight to hold your booklet open. Warranty Information We offer a lifetime warranty on any unused component that still has all protective films and stickers attached, or that is not functioning properly. You have waived the option for professional repair by attempting this on your own, therefore accepting responsibility for the outcome. The Apple warranty is void when the device is damaged, but further opening the device will void any supplemental insurance you may have purchased. More help and info can be found at iCracked.com/warranty. iPhone 6 Screen Replacement
3
step
1
Power Off and Remove Screws
Hold the power/sleep button down on the right side until “slide to power off� shows up on the screen. Slide the arrow from left to right. Note: If the screen is not functioning, power off the iPhone by holding down both the power button and the home button until the screen goes black, then release.
Pentalobe screwdriver
Remove the two Pentalobe screws next to the lightning port connector using a Pentalobe screwdriver. 4
iPhone 6 Screen Replacement
step
2
Lift and Separate Screen A
B
C Suction Cup
Spudger
A. Press the provided suction cup on the screen just above the home button. B. Carefully begin to pull up on the suction cup ring to create a gap between the plastic bezel surrounding the screen and the frame. C. Directly above the headphone jack is a trimmed area in which you will insert the flat end of the nylon spudger. Twist the spudger to help open the gap. NOTE: If the screen is shattered, place 2 to 3 pieces of packing tape over the shattered glass to form a flat suction surface.
iPhone 6 Screen Replacement
5
step
3
Lift and Hold Screen
Lift the bottom of the display assembly away from the rear case until it forms a 90-degree angle. CAUTION: Do not try to completely remove the display assembly from the frame! There are three flex cables still attached to the top of the iPhone, and removing the display assembly at this stage can destroy them.
6
iPhone 6 Screen Replacement
step
4
Disconnect Battery
Phillips screwdriver
Spudger
Continue holding the display assembly upward with one hand. Remove the two Phillips screws holding the battery plate in place. Remove the battery connector plate and set aside. Insert the pointed end of the spudger under the battery connector and gently lift up.
Note: Do not to pry up the socket on the logic board. You may break the connector entirely.
iPhone 6 Screen Replacement
7
step
5
Remove EMI Shield
Phillips screwdriver
Remove the five Phillips screws securing the EMI shield to the logic board. Remove the EMI shield and set aside. Note: The different color-marked screws are different sizes; note this as you set the screws aside for reassembly.
8
iPhone 6 Screen Replacement
step
6
Disconnect Four Flex Cables
2
1 4
3 Spudger
Insert the pointed end of the spudger beneath, and then lift up to disconnect: 1. Home button extension cable 2. Front-facing camera cable 3. LCD flex cable 4. Digitizer flex cable
iPhone 6 Screen Replacement
9
step
7
Remove Screen
Remove the screen assembly and lay it face down. Do not discard the damaged screen. Note: There are several items that will be transferred from the old display assembly to the new display assembly.
10
iPhone 6 Screen Replacement
step
8
Remove Ear Speaker Bracket
Phillips screwdriver
Remove the ear speaker and camera bracket by removing three Phillips screws. Remove the bracket and set aside.
iPhone 6 Screen Replacement
11
step
9
Remove Ear Speaker
Gently lift the right side of the camera assembly toward the left to expose the ear speaker. Remove the ear speaker and set aside.
12
iPhone 6 Screen Replacement
step
10
Remove Home Button Bracket
Phillips screwdriver
Remove the two screws holding the home button brackets in place. Remove the bracket and set aside.
iPhone 6 Screen Replacement
13
step
11 00
Disconnect Home Button Flex Cable
Spudger
Disconnect the home button flex cable, located left of the home button on the underside of the screen, by inserting the pointed end of the spudger beneath the connector and gently lifting.
14
iPhone 6 Screen Replacement
step
12 00
Unscrew Thermal Plate
Phillips screwdriver
Remove seven screws holding the large silver thermal plate to the screen. Note: The different color-marked screws are different sizes; note this as you set screws aside. iPhone 6 Screen Replacement
15
step
13
Heat Bottom of Screen
Heat Tool
Turn the display face-up, and gently heat the glass to the right of the home button with a hair dryer or heat gun. CAUTION: Too much heat can damage the device. Watch the repair video on our YouTube channel for proper heating instructions and demonstration.
16
iPhone 6 Screen Replacement
step
14
Peel Home Button Flex Cable
Spudger
Turn the display face-down again and use the flat end of the spudger to peel under the home button flex cable.
iPhone 6 Screen Replacement
17
step
15 00
Remove Home Button
Spudger
Using the flat end of the spudger, push the home button upward through its opening. You want to separate the rubber gasket from the screen. Remove the home button assembly and set aside.
18
iPhone 6 Screen Replacement
step
16 00
Reheat Bottom of Screen
Heat Tool
Turn the display face-up again, and gently heat the glass to the right of the home button with a hair dryer or heat gun. CAUTION: Too much heat can damage the device. Watch the repair video on our YouTube channel for proper heating instructions and demonstration.
iPhone 6 Screen Replacement
19
step
17 00
Remove Thermal Plate
Spudger
Using the spudger, carefully lift the home button extension flex cable from left to right. Remove and set aside the thermal plate.
20
iPhone 6 Screen Replacement
step
18 00
Heat Top of Screen
Heat Tool
Turn the display face-up again, and gently heat the top of the screen surrounding the camera lens and speaker with a hair dryer or heat gun. CAUTION: Too much heat can damage the device. Watch the repair video on our YouTube channel for proper heating instructions and demonstration.
iPhone 6 Screen Replacement
21
step
19 00
Peel Camera Cable
Spudger
Carefully peel up the front-facing camera cable from the right side to the left using the pointed end of the spudger. Note: Do not lose the rubber gasket for the ambient light sensor, shown still attached.
22
iPhone 6 Screen Replacement
step
20 00
Reheat and Disconnect Microphone
Heat Tool
Spudger
Turn the display assembly over again face up and apply more heat to the glass surrounding the front-facing camera with a hair dryer or heat gun. The upper microphone beneath this area is attached with strong adhesive and requires steady heat to weaken it.
Turn the display over face down. Very carefully peel up the gold block that is the upper microphone using the spudger along the bottom edge. iPhone 6 Screen Replacement
23
step
21 00
Remove Camera, Filter, and Film
Remove the front-facing camera assembly and set aside. Retrieve the ambient light sensor filter (white sticker) located in the sensor bracket and transfer it to your new screen.
Note: Only black assemblies have this white sticker. If you have a white iPhone screen, disregard the sticker step.
If your new assembly has an anti-static protective film covering the back side of the LCD, remove it before you begin reassembly. 24
iPhone 6 Screen Replacement
step
22 00
Transfer Spacers, Check Gasket & Adhesive
Remove the rubber spacers from the bottom of the original display assembly and transfer to the new display assembly.
Make sure the rubber ambient light sensor gasket is in place over the ambient light sensor as shown.
Peel the adhesive from the ear speaker rubber gasket for the upper microphone. iPhone 6 Screen Replacement
25
step
23
Align Microphone and Thermal Plate
Align the microphone onto the bezel, make sure the flex cable is placed over the alignment pin. Note: The orientation of the cable shown is intentionally improper in order to illustrate the microphone clearly. It will need to be turned around.
Align the thermal plate. Make sure the home button flex extension cable sits in front of the ledge of the bezel.
26
iPhone 6 Screen Replacement
step
24
Install Thermal Plate
Phillips screwdriver
Lay the thermal plate on the new assembly and screw in the seven Phillips screws holding the thermal plate in place.
iPhone 6 Screen Replacement
27
step
25 00
Install Home Button
Align the home button onto the new display assembly and press into place. Rest the flex button onto the two alignment pins indicated in red.
28
iPhone 6 Screen Replacement
step
26 00
Connect Home Button
Connect the home button flex cable onto the extension flex cable. Note the before (top) and after (bottom) images for reference.
Phillips screwdriver
Install bracket over the alignment pin, green. Insert and tighten two Phillips screws, red. iPhone 6 Screen Replacement
29
step
27 00
Set Sensor and Insert Ear Speaker
Lay the proximity and ambient light sensor into their brackets within the display assembly.
Insert the ear speaker into its rubber boot housing to the left of the front facing camera housing. Make sure that the oval opening on the back of the speaker drops into the ear speaker grill on the assembly. 30
iPhone 6 Screen Replacement
step
28 00
Install Camera
Lay the front-facing camera into the centering bracket. Double check that the ear speaker contacts, indicated in green, on the end of the front-facing camera/accessory flex cable are not damaged, torn or folded underneath the cable.
iPhone 6 Screen Replacement
31
step
29
Align and Attach Speaker Bracket
Place the ear speaker retaining bracket over the ear speaker. Make sure the flex cable and bracket align over the two pins. The two alignment pins should have passed through the ear speaker retaining bracket.
Phillips screwdriver
Insert and tighten the three Phillips screws that hold the ear speaker retaining bracket in place. 32
iPhone 6 Screen Replacement
step
30
Connect Four Flex Cables
2
1
3
4
Reconnect these cables in this order: 1. Digitizer flex cable 2. LCD flex cable 3. Front-facing camera cable 4. Home button extension cable
iPhone 6 Screen Replacement
33
step
31
Install EMI shield
Phillips screwdriver
Place the EMI shield over the four connected flex cables. Insert and install the five Phillips screws.
34
iPhone 6 Screen Replacement
step
32
Connect Battery
Connect the battery to the logic board.
Place the battery/dock connector flex cable retaining plate in place. Phillips screwdriver
Insert and tighten the two Phillips screws. iPhone 6 Screen Replacement
35
step
33
Do Not Close iPhone Yet
Lay the display assembly down onto the frame of the iPhone. Power on the iPhone, and test the display, touch screen, home button, front camera, upper microphone, and the proximity sensor.
36
iPhone 6 Screen Replacement
step
34 00
Align Tabs
If all tests are satisfactory, close the iPhone. The top of the display assembly has four tabs that must be aligned and inserted into the frame as shown. Lower the top of the display assembly at about a 20-degree angle into the slots cut into the frame.
iPhone 6 Screen Replacement
37
step
35 00
Set Bottom, Then Sides of Display
Press the bottom of the display assembly into the frame.
Press the left and right side into the frame.
38
iPhone 6 Screen Replacement
step
36
Re-install Screws
Pentalobe screwdriver
Re-install the two Pentalobe screws next to the lightning port plug using a Pentalobe screwdriver. THE END! After showing that repair who’s boss, do you think you have what it takes to be part of the most elite repair organization in the world as an iCracked iTech? Apply online today! www.iCracked.com/iTech Recycle Your Screen for Free! When finished with your repair, place your old screen inside the included white screen carrier. Place the carrier and old screen into the blue box. Apply the included prepaid shipping label to the blue box, seal it with tape, and drop it into the mail.
Tell your friends about your awesome repair and connect with us online!
iPhone 6 Screen Replacement
39
Š2014 iCracked, Inc. All rights reserved. All references to iCracked, the iCracked logo, and Mobi logo are trademarks of iCracked, Inc. iPhone, iPod, and iPad are trademarks of Apple, Inc. iCracked is an Independent Service Company and is in no way affiliated with Apple, Inc. But we love them!