iPhoneÂŽ 7 Plus Repair Flowchart
Back Up Your Device Repairing a device comes with the risk of damaging important components and losing data. Before repairing, securely back up your device. Back Up Via iTunes Connect your device to your computer and open iTunes. Select your device in the upper right corner and select Back Up Now in the Backups Window. Back Up Via iCloud Make sure you are connected to the Internet via WiFi. Go to Settings>iCloud>Storage & Backup. Switch iCloud Backup to ON and tap Back Up Now.
Tools Needed
#00 Phillips Screwdriver
Pentalobe Screwdriver
Suction Cup
2
Y00 or Y000 Screwdriver
Spudger or Pry Tool
iPhone 7 Plus Screen Replacement
Tweezers
Heat Tool
Watch the Video Before you begin, watch our online repair video. Visit our YouTube channel and find your device. www.YouTube.com/iCrackediPhoneRepair
Important Tips Take Your Time Allow 1-2 hours for this repair and be patient. Most mistakes are caused by rushing through the steps. Be Gentle Remember that you are handling fragile hardware. Stay Organized Note the placement of screws and small parts as you disassemble the device. Keep screws and small parts from each step in separate, small compartments or containers, like drink caps, or laid out on a clean flat surface. Use a paperweight to hold your booklet open. Warranty Information We offer a lifetime warranty on any unused component that still has all protective films and stickers attached, or that is not functioning properly. You have waived the option for professional repair by attempting this on your own, therefore accepting responsibility for the outcome. The Apple warranty is void when the device is damaged, but further opening the device will void any supplemental insurance you may have purchased. More help and info can be found at iCracked.com/warranty. iPhone 7 Plus Screen Replacement
3
step
1
Power Off and Remove Screws
Hold the power/sleep button down on the right side until “slide to power off� shows up on the screen. Slide the arrow from left to right. NOTE: If the screen is not functioning, power off the iPhone by holding down both the power button and the home button until the screen goes black, then release.
Pentalobe screwdriver
Remove the two Pentalobe screws next to the lightning port connector using a Pentalobe screwdriver. 4
iPhone 7 Plus Replacement
step
2
Apply Heat & Place Suction Cup
Heat Tool
Suction Cup
Using a hot air gun or hair dryer, warm up the screen to approximately 100 F to loosen the gasket between the bezel and the frame. After heating, attach the suction cup to the glass just above the home button. Pulling up with light force, you should see a gap appear just above the headphone jack. You may need to heat multiple times to get adhesive to release. NOTE: If the screen is shattered, place 2 to 3 pieces of packing tape over the shattered glass to form a flat suction surface.
iPhone 7 Plus Screen Replacement
5
step
3
Lift and Separate Screen A
B
Spudger
A. While lifting with the suction cup, begin running the spudger along the left edge of the phone in order to separate the display from the frame. B. Carefully repeat on the right side. There are flex cables located along the right side.
6
iPhone 7 Plus Screen Replacement
step
4
Lift and Hold Screen
There are locking tabs at the top of the display bezel. Release these tabs by slipping the top of the display toward the bottom. CAUTION: Do not try to completely remove the display assembly from the frame! There are several flex cables still attached to the top of the iPhone, and removing the display assembly at this stage can destroy them. Open the display assembly away from the frame, like a book, in order to access the cables and brackets. Make sure the display is set onto the frame itself.
iPhone 7 Plus Screen Replacement
7
step
5 00
Remove Retaining Plate
Tri-Wing screwdriver
Locate the battery/dislplay assembly/home button retaining plate and remove the 4 screws that hold the plate in place. Remove the retaining plate.
8
iPhone 7 Plus Screen Replacement
step
6
Disconnect Battery Cable
Spudger
Using the pointy end of the spudger, lift from under the battery cable’s metal edge and disconnect the flex cable from the connector. CAUTION: Only pry up on the connector and not the socket it came from. If you pry up on the logic board socket, you may break the connector completely.
iPhone 7 Plus Screen Replacement
9
step
7
Disconnect LCD & Home Button Cables
1
2
Spudger
Using the pointy edge of the spudger, lift up to disconnect the following: 1. LCD/Digitizer flex cable 2. Home button extension/force touch cable 10
iPhone 7 Screen Replacement
step
8
Remove Retaining Bracket
Y00 screwdriver
Slide the display down a bit to get clear access to the camera retaining bracket at the top right of the phone. Remove the three Tri-wing screws. Remove the retaining bracket.
iPhone 7 Screen Replacement
11
step
9 00
Disconnect Camera Flex Cable
Spudger
Disconnect the front-facing camera flex cable from the logic board. The area shown is the safest area to not accidentally damage any logic board components.
12
iPhone 7 Screen Replacement
step
10
Remove Display Assembly
Remove the display assembly from the iPhone. NOTE: There are several parts that will be transferred from the old display assembly to the new display assembly.
iPhone 7 Screen Replacement
13
step
11
Remove Frame Adhesive
Using the spudger, remove all black and white adhesive on the inner perimeter of the frame. DO NOT use any metal tools. They can scratch or damage the frame. CAUTION: Be extremely careful when removing the adhesive. If the tool slips, there is potential to cause irreparable damage.
14
iPhone 7 Screen Replacement
step
12
Remove Screws
Phillips screwdriver
Using a #00 Phillips screwdriver, remove the five Phillips screws securing the ear speaker and camera bracket to the display assembly.
iPhone 7 Screen Replacement
15
step
13 00
Remove Bracket
Remove the ear speaker retaining bracket.
16
iPhone 7 Screen Replacement
step step
14 00
Remove Ear Speaker
Gently lift the front-facing camera up and fold over to the left to expose the ear speaker.
Remove the ear speaker.
iPhone 7 Screen Replacement
17
step
15
Remove Screws & Retaining Bracket
Y00 screwdriver
Using a Y00 screwdriver, remove the four tri-wing screws holding the home button retaining bracket in place. Remove the home button retaining bracket. NOTE: The home button is screwed to the retaining plate. Take caution to not allow the home button flex cable to be torn. 18
iPhone 7 Plus Replacement
step
16
Separate Cables CAUTION: The home button flex cable within the display is free-floating and not adhered to the bezel. Take extreme caution disconnecting the home button flex cable from the home button extension cable.
Spudger (x2)
Using two spudgers, hold the bottom cable down while separating the top cable
iPhone 7 Plus Screen Replacement
19
step step
00 17 00
Heat Display
Heat Tool
Heat the display in the area shown in order to assist in loosening the adhesive holding the home button flex cable to the bezel.
20
iPhone 7 Plus Replacement
step step
00 18 00
Separate Cable from Bezel CAUTION: If the home button is damaged, this will render the phone unusable. The home button with flex cable CANNOT be replace and retain fingerprint scanning.
Spudger
GENTLY slide the flat end of the spudger under the home button flex cable to separate it from the bezel.
iPhone 7 Plus Screen Replacement
21
step step
00 19 00
Remove Home Button
Carefully slide the home button and flex cable out through the front of the display.
22
iPhone 7 Plus Replacement
step step
00 20 00
Reheat and Disconnect Microphone
Heat Tool
Turn the display assembly over and heat the indicated area with a hot air to loosen the proximity sensor from its bracket on the underside.
iPhone 7 Plus Screen Replacement
23
step step
00 21 00
Lift Sensors from Display
Lift the ambient light sensor free from the display assembly.
Go to the opposite side and lift the proximity sensor free from the display assembly.
24
iPhone 7 Plus Replacement
Lift Microphone step
00 22
Insert Step Title Here
Spudger
Carefully use the flat end of the spudger to get underneath the front-facing camera cable and slide it under in order to break the adhesive loose from the bezel. NOTE: Before you start sliding the spudger underneath, look closely and ensure you are under the cable and not in between the two halves of the cable.
iPhone 7 Plus Screen Replacement
25
step
23 00
Remove Cable
Spudger
Continue to lift the cable under the microphone. CAUTION: Do not pull the cable. You will most likely tear it.
Remove the front-facing camera and set aside.
26
iPhone 7 Plus Screen Replacement
step
24 00
Locate Ambient Light Filter
NOTE: The ambient light filter should be preinstalled on the new display. Black screens will have a white filter and white screens will have a yellow filter. Should these be missing, it is vital that you move it from the original display to the new display.
iPhone 7 Screen Replacement
27
step
25
Locate Rubber Gasket
NOTE: A rubber gasket should be attached to the ambiet light sensor. Do not lose it.
28
iPhone 7 Plus Screen Replacement
Transfer Filter & Remove Assembly Cover
step
26
If not preinstalled, remove and transfer the ambient light sensor filter located in the ambient light sensor bracket built into the bezel. Ttransfer to the new display assembly.
Black screen has a white filter
White screen has a yellow filter
Remove the anti-static cover from the back of the display assembly. iPhone 7 Plus Screen Replacement
29
step
27
Install Home Button
Pass the home button and flex cable through the front of the display. Align the flex cable onto the two pins within the bezel. Make sure the flex cable goes under the home button extension cable. Set the cable onto the alignment pin on the bezel.
30
iPhone 7 Screen Replacement
step
28
Connect Cable
Connect the home button to the home button flex cable.
iPhone 7 Screen Replacement
31
step
29
Install Screws
Tri-Wing screwdriver
Align the home button bracket over the connector shown by the arrow. Insert and tighten the four tri-wing screws.
32
iPhone 7 Plus Replacement
step step
30 00
Remove Adhesive Backing
Remove the adhesive backing over the microphone area.
iPhone 7 Screen Replacement
33
step step
31 00
Install Microphone
Align the ear speaker contacts on the frontfacing camera cable with the two pins in the display. Lay the microphone into place.
34
iPhone 7 Screen Replacement
step
32
Insert Sensors
Set the proximity sensor into its bracket.
Set the ambient light sensor into its bracket.
iPhone 7 Screen Replacement
35
step
33 00
Insert Ear Speaker
Set the ear speaker in place, making sure the spring contacts are at the bottom and the ear speaker is pushed into the rubber gasket. If you release the ear speaker, it should stay in place.
36
iPhone 7 Screen Replacement
step
34 00
Connect Front-Facing Camera
Fold the front-facing camera over the top of the ear speaker and set into the bracket.
iPhone 7 Screen Replacement
37
step
37 00
Insert Retaining Bracket
Phillips screwdriver
Place the retaining bracket for ear speaker and front-facing camera in place. Insert and tighten the five Phillips screws.
38
iPhone 7 Screen Replacement
step
38
Install Adhesive
Before installing the new display assembly, replace the inner frame adhesive. Peel off the larger area of the adhesive backing so that only the adhesive that sets inside the frame remains.
iPhone 7 Screen Replacement
39
step
39
Install Adhesive
Set the inner adhesive backing into the frame. Notice there is a cutout that frames the rear camera area.
40
iPhone 7 Screen Replacement
step
40
Install Adhesive
Gently use the spudger to smooth the adhesive onto the frame. Do this around the entire circumference of the phone.
iPhone 7 Screen Replacement
41
step step
41 00
Install Adhesive
Carefully remove the middle layer of adhesive. You will be left with the gasket and inner protector still attached. This will allow you to install the display without pulling the gasket off the frame.
Verify your front-facing camera cable is installed correctly. It should lay down exactly as shown. 42
iPhone 7 Screen Replacement
step step
42 00
Connect Front-Facing Camera
Connect the front-facing camera cable onto the logic board. CAUTION: Do not force the cable into the socket. If it’s not seating properly, the cable is either not aligned or debris has fallen into the connector.
iPhone 7 Screen Replacement
43
step
43
Re-install Screws
Phillips screwdriver
Place the retaining bracket for the cameras back into place. Insert and tighten the two Phillips screws.
44
iPhone 7 Screen Replacement
step
44
Connect Home Button Flex Cable
Open the display like a book, making sure the display is resting on top of the frame. Connect the home button/force touch flex cable. CAUTION: Do not force the cable into the socket. If it’s not seating properly, the cable is either not aligned or debris has fallen into the connector.
iPhone 7 Screen Replacement
45
step
45
Connect Cables
1
2
Connect the following cables in order: 1. LCD/Digitizer flex cable 2. Battery flext cable CAUTION: Do not force the cable into the socket. If it’s not seating properly, the cable is either not aligned or debris has fallen into the connector. 46
iPhone 7 Replacement
step
46
Insert Screws
Tri-Wing screwdriver
Place the flex cable retaining bracket over the flex cables. Insert and install the four tri-wing screws. NOTE: Do not over-tighten the retaining plate screws. They are in close proximity to the logic board and irreparable damage to the logic board is possible. iPhone 7 Screen Replacement
47
step
47
Power On & Test NOTE: Do not close the iPhone all the way yet.
Lay the display assembly down. Power on the iPhone. Test the display, touch screen, home button, front camera, upper microphone, and the proximity sensor. Once you are satisfied all components are working power down the phone and continue reassembly.
48
iPhone 7 Replacement
step
48
Remove Adhesive
Lay the display on top of the frame and, while pulling slightly to the left, remove the left side adhesive backing from the internal gasket.
iPhone 7 Screen Replacement
49
step
49
Remove Adhesive
Open the display again like a book and remove the left side adhesive backing from the internal gasket.
50
iPhone 7 Replacement
step
50
Install Display Assembly
NOTE: The display assembly has two tabs that must be aligned and inserted into the frame, as shown.
Slide the top end of the tabs under the frame, as shown. iPhone 7 Screen Replacement
51
step
51
Install Display Assembly
Pentalobe screwdriver
Starting at the bottom of the screen, press around the edges of the display assembly. Insert the two Pentalobe screws next to the lightning port. 52
iPhone 7 Replacement
step
52
The End THE END! After showing that repair who’s boss, do you think you have what it takes to be part of the most elite repair organization in the world as an iCracked iTech? Apply online today! www.iCracked.com/iTech Recycle Your Screen for Free! When finished with your repair, place your old screen inside the included white screen carrier. Place the carrier and old screen into the blue box. Apply the included prepaid shipping label to the blue box, seal it with tape, and drop it into the mail.
Tell your friends about your awesome repair and connect with us online!
iPhone 7 Screen Replacement
53
Š2017 iCracked, Inc. All rights reserved. All references to iCracked, the iCracked logo, and Mobi logo are trademarks of iCracked, Inc. iPhone, iPod, and iPad are trademarks of Apple, Inc. iCracked is an Independent Service Company and is in no way affiliated with Apple, Inc. But we love them!