Efficient Design of Differential Trans- Conductance Amplifier with Sub-Threshold Biasing Stabilizati

Int. Journal of Electrical & Electronics Engg.

Vol. 2, Spl. Issue 1 (2015)

e-ISSN: 1694-2310 | p-ISSN: 1694-2426

Efficient Design of Differential TransConductance Amplifier with Sub-Threshold Biasing Stabilization in Low Power CMOS Technologies Jasmeen Kaur1, Vishal Mehta2 1

2

School of Electronics and Electrical Engineering, Chitkara University, Rajpura, India Chitkara University Research and Innovation Network, Chitkara University, Rajpura, India 1

jasmeen.kaur@chitkara.edu.in, 2vishal.mehta@chitkara.edu.in

Abstract: In this paper, a low voltage differential CMOS trans-conductance amplifier using 180nm on cadence is presented. This design operates in sub threshold region of ±0.5V-1.5V and biasing stabilization has been checked by observing relationship between differential voltage and biasing variations on Nano-scale. Simulation results shows maximum differential output is obtained when biasing current reaches 500nA with CMRR 88db and static power consumption on normal input conditions is 241nW. In this paper, layout of OTA has been presented after verifying DRC and LVS by using assura tool of cadence suite.

Keywords- OTA; virtuoso; assura; spectre; bias

I. INTRODUCTION Due to the advancement in technology and rapid growth of the microelectronics circuits, the low voltage, low power and high performance circuits are generally preferred in VLSI industry [1]-[3]. The transconductance Amplifier is one of the basic building blocks of any analog application [4]. The Transconductance Amplifier is widely used in integrated amplifier, filter and discrete applications. The transconductance amplifier has differential voltage input i.e. it takes the difference of the input voltages V1 and V2 which produces the current as output. Hence transconductance amplifier is basically voltage controlled current source. The output current will vary according to the differential input voltage applied while keeping the accuracy and linearity maintained [5]. In recent years, various transconductance amplifier circuits has been purposed having low operating voltage and low power dissipation .The transconductance amplifier differs from conventional operational amplifier in output as output of conventional operational amplifier is voltage whereas in Transconductance Amplifier, output is current [6-9].

where Gm1 and Gm2 is positive transconductance and negative transconductance respectively. Fig 1 shows the Transconductance Amplifier where Vin+ is the noninverting input voltage and Vin- in inverting input. Fig 2 shows the basic concept used in transconductance amplifier with differential inputs V1 and V2. Voltage Vb is used to generate the biasing current Ib in the circuit.

Transistor Qb will act as current source. Differential input is used in the circuit which provide better common mode rejection ratio (CMRR), reduce harmonic distortions in the circuit and produce increased output voltage as compared to the single ended Amplifier [11-12].

Fig 1- Transconductance Amplifier

Fig 2- Differential Pair input of Trans-conductance Amplifier

II. BASIC CIRCUIT CONFIGURATION An ideal differential input Transconductance Amplifier has infinite input and output impedance [10]. The ideal transfer characteristics of operational transconductance amplifier is given as Iout1 = Gm1 (V1 − V2) (1) Iout2 = Gm2 (V1 − V2) NITTTR, Chandigarh

(2) EDIT -2015

III. PROPOSED CIRCUIT In this paper, a transconductance amplifier with biasing stabilization is designed. Fig 3 shows the schematic diagram of this transconductance amplifier designed using Cadence Virtuoso tool using 180nm technology. In this schematic, transistor M4, M5, M6 and M7 will act as differential transistor. Input voltage V1 and V2 is applied 14

Int. Journal of Electrical & Electronics Engg.

Vol. 2, Spl. Issue 1 (2015)

e-ISSN: 1694-2310 | p-ISSN: 1694-2426

to transistor M4, M5, M6 and M7 whose difference is converted to output current. Rest of the transistors is used as current mirrors. These transistors have same source gate voltages which will produce almost same drain current.

Hence, these transistors will act as current mirrors. In current mirror circuit output current is approximately equals to input current.

Fig 5- Transient response of Transconductance Amplifier

Fig 3- Schematic of transconductance Amplifier

Fig.4 represent optimized Layout view of the given schematic which is designed using Cadence tool (Virtuoso layout Editor) and physical verification of layout design is done using Cadence Assura tool.

Table 1 show the amplified output response of the voltage is varied from 0.50V to 1.50V.I-bias is set to 50nA. As shown in the table 1, output voltage will increase with the increase in input voltage.

Table 1- Variation of output voltage with input voltage Vin1

Vin2

Vout1

Vout2

0.50 V

-0.50 V

1.80V

1.454V

0.75 V

-0.75V

1.85V

1,458V

1V

-1V

1.88V

1.463V

1.25V

-1.25V

1.94V

1.469V

1.50V

-1.50V

1.99V

1.479V

Table 2 shows the variation of output voltage with the change in biasing current Ibias at differential input voltage Âą0.75V and Vdd 1.8V. Table 2- Variation of output voltage with biasing current

Fig 4- Optimized Layout design of Transconductance Amplifier

IV. RESULT & DISCUSSIONS The simulation of the circuit shown in Fig 3 is done using Cadence Spectre tool in 180nm CMOS technology. Fig 5 shows the output transient response of the given circuit when Âą0.75V is applied at the differential inputs having Ibias current equals to 50nA and Vdd is set to 1.8 V 15

Ibias

Vout1

Vout2

25n A

1.83V

1.47V

50n A

1.845V

1.458V

100n A

1.85V

1.43V

200n A

1.852V

1.40V

500n A

1.855V

1.37V

Fig 6 shows the DC response of the given transconductance amplifier. Static power consumption of the circuit is calculated using calculator in Cadence Spectre tool and it is approximately equals to 241.93 nW.

NITTTR, Chandigarh

EDIT-2015

Int. Journal of Electrical & Electronics Engg.

Vol. 2, Spl. Issue 1 (2015)

e-ISSN: 1694-2310 | p-ISSN: 1694-2426

V. CONCLUSION In this paper we represent differential trans-conductance amplifier for low power applications. This amplifier can be used for low voltage transducers, filter designs and ADC circuits. Low power consumption also increases its significance in delta sigma modulator circuits where gain stabilization is required at different varying conditions.

REFERENCES

Fig 6- DC characteristics of Transconductance Amplifier

Fig 7 shows the AC response of the circuit which represents the gain and phase change with frequency.

Common mode rejection ratio (CMRR) of the circuit is calculated and is equals to 88db.

Table 3 shows the Simulated Characteristics of Transconductance Amplifier. The simulated result shows that the power consumption and CMRR with given characteristics is 241.93nW and 88db respectively.

Specifications

Table 3- Design specifications Simulated

CMOS technology

180nm

Vdd

1.8V

Supply voltage

±0.5V-±1.5V

Bias Current

50n A

CMRR

88db

Static Power Consumption

241.93nW

[1] Chandrakasan, Anantha P., Samuel Sheng, and Robert W. Brodersen.

"Low-power CMOS digital design." IEICE Transactions on Electronics 75.4 (1992): 371-382.

[2] Raikos, George, and Spyridon Vlassis. "0.8 V bulk-driven operational amplifier." Analog integrated circuits and signal processing 63.3 (2010): 425-432.

[3] SILVEIRA, F., FLANDRE, D. Low power analog CMOS for cardiac pacemakers. Design and Optimization in Bulk and SOI Technologies.

Kluwer Academic Publishers, 2004 [4] Nguyen, Trung-Kien, and Sang-Gug Lee. "Low-voltage, low-power CMOS operation transconductance amplifier with rail-to-rail differential input range." Circuits and Systems, 2006. ISCAS 2006. Proceedings.

2006 IEEE International Symposium on. IEEE, 2006.

[5] T.Y. Lo and C.C. Hung, “A 1 GHz OTA-based low-pass filter with a high speed automation tuning scheme,” IEEE Asia solid-stage conference, pp. 408-411, 2007.

[6] Yavari, Mohammad, and Omid Shoaei. "Low-voltage low-power fastsettling CMOS operational transconductance amplifiers for switchedcapacitor applications." IEE Proceedings-Circuits, Devices and Systems 151.6 (2004): 573-578.

[7] Zao, Liu, et al. "The design and optimization of gain-boosted OTA for high speed and high accuracy sample and hold amplifier." ASIC, 2007.

ASICON'07. 7th International Conference on. IEEE, 2007.

[8] P. Corbishley and E.R. Villegas, “A Low Power Low Voltage Rectifier Circuit,” MWSCAS '06, vol. 2, pp. 512–515, 2006.

[9] de Carvalho Ferreira, L. H., and T. C. Pimenta. "An ultra low-voltage ultra low power rail-to-rail CMOS OTA Miller." Circuits and Systems, 2004. Proceedings. The 2004 IEEE Asia-Pacific Conference on. Vol. 2.

IEEE, 2004.

[10] Chanapromma, Chaiyan, and Kanchana Daoden. "A CMOS fully differential operational transconductance amplifier operating in subthreshold region and its application." Signal Processing Systems (ICSPS), 2010 2nd International Conference on. Vol. 2. IEEE, 2010.

[11] Mohieldin, Ahmed Nader, Edgar Sánchez-Sinencio, and José SilvaMartínez. "Nonlinear effects in pseudo differential OTAs with CMFB." Circuits and Systems II: Analog and Digital Signal Processing, IEEE Transactions on 50.10 (2003): 762-770.

[12] Mohieldin, Ahmed N., Edgar Sánchez-Sinencio, and José SilvaMartínez. "A fully balanced pseudo-differential OTA with common-mode feedforward and inherent common-mode feedback detector." Solid-State Circuits, IEEE Journal of 38.4 (2003): 663-668.

Fig 7- AC characteristics of Transconductance Amplifier

NITTTR, Chandigarh

EDIT -2015

16