Building Business August 2012

building business the latest news FROM YOUR building supplies SPECIALIST

ISSUE 44 : AUGUST 2012

Get your

2012 ITM cup draw inside Photo Credit: Rick Moran

LEAKY BUILDINGS

Bracing Specification

What are they and why get involved?

Pg 2-3

Understanding the changes Pg 12-13

Reading BUILDING BUSINESS will contribute 1 point towards your LBP skills maintenance requirement.

Ensure you log this in your ITM diary TODAY. AUGUST 2012

LEAKy BUILDINGS

Series of Articles on Weathertight Remediation

by Harry Dillon

Leaky buiildings - what are they and why get involved?

WEATHERTIGHT REMEDIATION

Article one of NINE

Welcome to the first in a series of articles based on a series of workshops on weathertight remediation for builders which the Department of Building and Housing has been running at centres all over New Zealand.

As the presenter of this course I have been able to share some of my experiences from a decade of remediating leaky buildings with fellow builders.

Whilst it would be impractical to cover all of the content of this full day workshop in this series we aim to cover some key points that may assist any builder who is considering getting into this line of work to perform quality remediation and manage any project risks.

Harry Dillon

So what actually is a leaky building?

At some point in its life a building is highly likely to allow some water past its cladding. It is how the building deals with that moisture that is the key. If moisture can’t quickly drain out and/or if air can’t circulate to promote drying behind the cladding, extensive damage can result. By far the majority of the hundreds of buildings I have been involved with showed few, if any, visible signs of water penetration and resultant damage. You don’t need to have cracked exterior plaster or have interior linings falling from a ceiling to have trapped moisture related damage. A gradual and occasional introduction of moisture is all that may be required to create an environment suitable for decay to be present and flourish. This can be relatively rapid where little or no treatment is present in the affected framing.

We don’t actually know exactly how many buildings have been, are or will be affected.

A 2009 Price Waterhouse report estimates between 22,000 and 88,000 homes, with the industry consensus around 40,000. A truly staggering number of families have been, are and will be impacted by this estimated $11bn phenomenon. Whilst a majority of current cases are appearing in Auckland, many experts believe that it is a New Zealand wide problem.

Those residing in dryer geographical areas just may not have discovered it yet.

So how did we end up here?

There is much conjecture and controversy about what has caused this problem but it is my view in short, that it is a systematic failure of the industry as a whole. Complex, incomplete and questionable suitability of building design, poor use and suitability of some products, incomplete technical knowledge and skill as well as too little on-going training for many involved in the building process have all contributed.

Why get involved?

Clearly there are a large number of leaky buildings needing repairs. This presents an opportunity for builders at a time when new builds are at historic low levels. There is a perception that getting involved in leaky

In this issue Weathertight Remediation Remote Home Management GIB Technical Support ITM Cup Coaches Interview Scyon Linea Weatherboard Powertools Disturbing Trends in Construction Sector 2

2-3 4 4 5 6 7 8-9

Pink Batts Peace of Mind Paslode Impulse Framemaster-Li PSP ClearVue Ram Board Structural Bracing with Plywood Futurewood Bathrooms

10 11 11 11 12-13 13 14-15

Waste Services Rheem Water Heating Building Fales in Samoa The ITM Fishing Show Cemix Concrete Clipper and Norton Blades ITM Cup Rugby Pack Promo

16 16 17 18 19 19 20

home repair work is risky and best avoided. While arguably there are more risks and unknowns associated with these projects, if a builder goes in with eyes open and is aware of these risks and ways that they can be managed a successful outcome is more likely to result. This will be of benefit not only to the builder but also the client and all those involved in the project.

In this series of articles, I will be talking about a range of things that are important for the builder to be aware of including: • Assessing the projects risks • Working with the right team • Tendering • Health and safety • What happens on site • The 4 “D”s

Suggested follow up areas for more information

DBH website: http://www.dbh. govt.nz/ws-info-for-buildingprofessionals

The DBH publications • Guide to Remediation Design • Guide to the Diagnosis of Leaky Buildings • Dealing with Timber in Leaky Buildings • Code Watch Issue 1: October 2011

COMING UP IN OCTOBER Article 2: Leaky Buildings Getting Involved (by Harry Dillon)

The author: Harry Dillon is a builder and has been involved with the repair of over 300 homes over the last 10 years. This article represents Harry’s views which may not necessarily be the same as the Department of Building and Housing or ITM.

LBP SKILLS MAINTENANCE ROADSHOW BSM has partnered with the Department of Building and Housing (DBH) to facilitate the delivery of training for skills maintenance required for Licensed Building Practitioners (LBP).

The Roadshow is looking at aspects of the LBP scheme and providing practitioners with the opportunity to submit feedback that may influence changes needed, now that Restricted Building Work (RBW) is here.

THE ROADShow will review the following: • What should the role of the Site Licence be?

• Should the Site Licence be split into a ‘Technical Supervision’ Licence and a ‘Project Manager’ Licence?

• Should any new licences be developed?

• Do any of the current licence competencies and performance indicators need to be amended?

• Should any work that is currently RBW be specifically excluded from being RBW?

WHEN:

Up until 30th August. 5:30pm – 8pm

WHERE: Nationwide WHY:

Earn 4 LBP points by attending, provide feedback.

For more information and meeting dates and locations visit www.bsm.org.nz

Easy As 1-2-3 Take the hassle out of completing three copies of the Record of Building Work form with the ITM triplicate book. Complete the form once and three copies are created; one for the Homeowner, one for the Council and one copy for you the Builder.

The book holds 25 jobs and is now available from your ITM Store.

Get yours today!

3

DO IT ONCE, DO IT RIGHT TECHNICAL SUPPORT FROM WINSTONE WALLBOARDS WHEN YOU NEED IT Free advice is just a phone call away If you want to avoid time-consuming and expensive call-backs, then take the guesswork out of installing GIB® plasterboard systems.

With the GIB® technical helpline covered 5 days a week during business hours, you can get your questions answered quickly and at no cost. Even if the technical team don’t have the answer then and there, they’ll find the right solution and get back to you within 24 hours.

Or THEY’Ll come to you The GIB® technical team offers free on-site skills maintenance sessions with a focus on best practice installation techniques and GIB® plasterboard systems. What’s more, you’ll accrue Licensed Building Practitioner (LBP) points for participating.

Call the GIB® technical helpline to arrange a session or visit the website www.gib.co.nz/contactus.

GIB® TECHNICAL HELPLINE

0800 100 442 MON - FRI, DURING BUSINESS HOURS

REMOTE HOME MANAGEMENT The Schlage LiNK Starter Kit includes everything needed to create a remote access solution. Installation and setup is simple

The Schlage® Bridge (required) is the brain of the Schlage LiNK™ Solution, enabling various wireless components to be managed remotely via the internet.

The Schlage® Appliance Module allows homeowners to control appliances remotely using the Schlage LiNK™ Solution.

For more information visit linkyourhome.co.nz

The Schlage® Wireless Keypad Lock allows the homeowner to remotely lock and unlock doors*.

• Wireless lock/unlock operation • Receive notification when lock is used • There’s no key to hide, lose, carry or forget • Add, change or delete user codes in seconds • Up to 19 unique user codes.

*only when used with the Schlage LiNKTM Solution

FREE ITM BUILDERS GLOVES WHEN YOU SPEND $200 OR MORE ON THE PRODUCTS FEATURED ON THIS PAGE 4

NEW

PRODUCT

NEW ITM CUP COACHES ALL FIRED UP Craig Philpott (Hawkes Bay) and Tabai Matson (Canterbury) have both scored themselves head coach gigs for the first time in ITM Cup Premiership rugby and they’re all fired up for the coming season…

Your team’s prospects?

Craig: The key thing for us is preparing smart and recovering smart.

We’ve got a very big first week starting with Auckland on the Thursday, Wellington the following Tuesday and Counties on the Friday. And we have a very big last week too with Manawatu on the Saturday, Canterbury on the Wednesday and Waikato on a Saturday.

Tabai: Expectation. One of the things about wearing a red and black jersey is wherever you play, people tend to play their A game against you so there’s a huge expectation to always be at your best.

Tabai: As always, Canterbury has very high expectations. We won last Tabai Matson year, and the players are there to win it again this year. A couple of key people who are really going to help us are Scott Robertson who has been appointed as forward coach and Aaron Mauger assisting with the attack.

Tabai: We started last year’s final with an average age of 21.6 so we had a very young roster. This year, they’re a year wiser, they’ve had a few more games under their belts, and some of them have been in the Crusaders environment, so one of the key areas we’ve improved on is experience.

Craig Philpott

Any fitness or injury issues?

Craig: The big thing for us is how the super rugby competition pans out. We’ve got ten guys away playing across three different franchises who will be coming back to us quite late in the piece. In terms of injuries, the only one we’re aware of is Richard Buckman who will unfortunately miss the bulk of the competition.

Tabai: The only person we’ll be missing is Brendon O’Connor who sustained a serious knee injury during the Crusaders campaign. It’s a season ender, really tough for him. Right now, I’m touching wood because everyone else seems to be feeling very well.

Key strengths?

Craig: A really good mix of youth and experience. We’ve got some young guys coming through with the likes of NZ under 20s first five Ihaia West. He’s up against an experienced Daniel Waenga so there’s a nice mix of youth and experience there competing in that position.

How can you improve on last year?

Craig: We lost four games last year, three of them against teams we were probably expected to beat. I think a big thing for us is mental toughness around those potential banana skin games, the ones you think you’re going to win but you don’t.

Any All Blacks in the team?

Craig: Possibly Zac, Israel, Hika and Ben Tameifuna. I wouldn’t be holding my breath about seeing much of Israel, but we might get some game time out of the other three.

Tabai: Hopefully Andy Ellis and Corey Flynn. Obviously we’re hopeful that they become All Blacks for the four nations, but if not, we’ll welcome them with open arms as we do.

Your toughest match?

Craig: The next one we play. We’re up in the premiership this year, with the big boys, which is where Hawkes Bay belongs. We’ve got six really tough games against the other premiership teams and four crossover games which are tough games as well.

Tabai: In the first week, we play three games in eight days.

We play north Harbour two days after we play Auckland; North Harbour, that’s the tough one for us.

North Harbour don’t have a mid week game at that stage so they’ll have seven days turnaround so they’ll be waiting and ready for an ambush.

5

THE WEATHERBOARD THAT WEATHERS WELL

Scyon Linea Weatherboard ®

®

What is it?

A 16mm thick horizontal weatherboard with deep shadow lines.

Where do you use it?

In residential applications wherever a contemporary design is required, including external walls in composite construction, upper-storey and groundlevel extensions, and internal feature walls.

What are the key benefits?

Design options. The 16mm thick profile creates consistent deep shadows. The range of corner finishing details – aluminium, PVC or Scyon® Axent™ Trim – means that a range of different looks can be achieved. Face or concealed fixing rounds out the options. The boards are available in 3 widths – 135, 150 and 180mm.

Easy to install. Scyon® Linea® Weatherboards are back bevelled to sit flush with the stud. Paint application is fast because the pre-primed sheets mean less paint and time is needed to achieve a quality finish.

breakthrough CLD® manufacturing technology, allowing for enhanced durability and stability when painted dark colours compared with other traditional timber alternatives.

Enhances energy efficiency. When Scyon® Linea® Weatherboard is used with the right insulation and in accordance with Clause H1 of the New Zealand Building Code, an R-Value of up to 2.2 can be achieved for the wall.

Extra security. James Hardie provides a 25 year product warranty on Scyon® Linea® Weatherboard.

Made from Scyon.® Linea® Weatherboard is made from Scyon® the advanced lightweight cement composite with heavy-duty performance. Not only is it resistant to fire and moisture damage from rot1, but it can also be gun nailed and is easy to cut.

1 When installed and maintained correctly and to the extent set out in James Hardie’s published literature current at the time of installation.

For more information on Scyon Linea Weatherboard ASK JAMES HARDIE or visit www.scyon.co.nz

Low maintenance. Scyon® Linea® Weatherboard will maintain its integrity and general appearance1.

Scyon® Linea® Weatherboard will resist shrinking, swelling and cracking1 to hold paint longer. Scyon® Linea® Weatherboard pioneers James Hardie’s

FREE ITM BUILDERS GLOVES WHEN YOU SPEND $200 OR MORE ON THE SCYON PRODUCT FEATURED ON THIS PAGE 6

POWERTOOLS

12V 10mm Cordless DRILL/DRIVER

255mm TABLE SAW with STAND

• All-metal gear construction • Single sleeve keyless chuck • Ample power for general joinery and fit-out tasks #6271DWPE

• 1500 watt, 4300 rpm • Extension from blade - right 600mm, left 610mm • Rear extension 715mm from centre of table • Includes WST-03 Stand (JM27000300) #MLT100

$14900

EXCL GST

23mm Rotary Hammer Drill

• 720 watt • 2 modes, rotary hammer drilling or drilling • One-touch sliding chuck SDS-Plus • One-touch depth rod adjuster #HR2300X6

$29900

EXCL GST

W

NE

Two-Tool Combo Kit

• Brand new pro series DS18DSDL 13mm driver drill • WH18DSAL 1/4” impact driver • 2 x 4.0Ah ultra capacity lithium Ion batteries and fan cooled smart charger • Supplied in a Hitachi tough case # KC18DLL

$63900

EXCL GST

W

NE

4-Piece 18v Combo Kit

• Impact drill, impact driver, circular saw and 115mm angle grinder • 2 x 4.0Ah ultra high capacity batteries • Smart charger and site bag # KC18DRL

$99500

EXCL GST

$79900

EXCL GST

AUTO FEED ScrewDRIVER

• Accepts up to 55mm length screw • Silent clutch • Direct drive transmission in reverse rotation • Includes: 3 x Philips bits, belt hook, carry case #6846

$49900

EXCL GST

190mm deep Cut circular saw • A 7 1/2” saw that cuts like an 8 1/4” • Compact and lightweight 4.2kg • PTFE coated base for smooth sliding on work-pieces • Supplied with TCT saw blade (20T) • Massive 78mm depth of cut • Robust carry case included #C7UY

$29900

EXCL GST

262mm slide compound mitre saw • Soft start and electronic constant speed control • Belt-drive for optimum power and safety • Cut 100 x 100mm Timber in one pass #C10FSB

$89900

EXCL GST

FREE ITM BUILDERS GLOVES WHEN YOU SPEND $200 OR MORE ON THE POWERTOOLS FEATURED ON THIS PAGE 7

disturbing trends in the residential conStruction sector

A regular column by Geoff Hardy a Commercial Lawyer

For many years now, I have been providing legal advice to builders. These days, hardly a week goes by when I do not receive a call from a builder who is at an emotional breakingpoint over a dispute that has arisen with his client, and who tells me that in 20 (30, 40) years of building, he has never encountered as difficult a situation as the one he has contacted me about.

of deals on a handshake are gone, as are the days when unpaid debts were something to be ashamed of. And so in many building projects, the property owner seems to regard it as his choice whether he will pay the full contract price or not.

That approach has been made all the easier by the fact that building is a service that has traditionally been done on credit. In other words, the builder

Hardly a week goes by when I do not receive a call from a builder who is at an emotional breaking point over a dispute.

I don’t believe this is due to a decline in building standards in recent years. These builders all hold recognised qualifications in building, and they take pride in their work. They have all satisfied the strict criteria for becoming licensed building practitioners under the Building Act. Furthermore, they own and operate small businesses that are dependent on maintaining good relations with their customers to ensure the steady stream of income they rely upon to feed their families.

does the work first, and then hopes to be paid for it later. That gives the dissatisfied property owner enormous power. And it is simply human nature that more and more owners these days are going to be motivated to use, and abuse, that power.

Rather, I think it is due to the fast-paced, competitive, and stressful age we live in, and the general decline in tolerance and understanding that is the inevitable result of it. Like it or not, the days

THE CUNNING PLAN The usual ploy is so commonplace that I call it the “cunning plan�. That is, at some stage during the course of the project, the owner develops a

8

suspicion that he is being fleeced by the builder.

However rather than making genuine efforts to make sure he is right, he generally goes quiet until he has obtained possession of the building, and there is one more installment of the contract price owing to the builder.

The days of deals on a handshake are gone, as are the days when unpaid debts were something to be ashamed of.

His intention is not to pay that installment, nor to take any steps to resolve the underlying dispute.

That is because he already has everything he wants – he has the finished building, and he has the builder’s money. The plan is to use that money, either as leverage to ensure the owner “wins” the dispute, or alternatively to pay it to another builder to complete any remaining work and rectify any defects.

I am not suggesting that the builder is always right and the owner always wrong. Many builders do sub-standard work, and even if they don’t, they make a hash out of communicating with their client and working through issues of discontent. On the

his mind. The only party with any real incentive to do so is the builder, who probably owes 90% of the unpaid invoices to subcontractors and suppliers, and desperately needs the balance simply to make ends meet.

To counteract the unfair advantage that a disenchanted owner-in-possession has, the builder has to resort to the law. Fortunately there are now some cheaper and quicker options than litigation, available to him under the Construction Contracts Act 2002. But whether he wins or loses, that will often mean that he has spent all of his profit margin on recovering his money, and he has effectively built that house for free.

TILTING THE PLAYING FIELD This would be hardship enough, were it not for the fact that the Government appears blind to this reality. Ever since the 2002 Hunn Report mistakenly concluded that builders were effectively immune from any accountability under the law, the Department of Building and Housing has been hell-bent on tilting the playing field more in favour of the homeowner. And so in addition to a number

We are on the verge of a building boom that will see supply and demand in the building secotr radically reversed. of worthwhile reforms such as builder licensing and building consent simplification, we are now seeing a rash of extra consumer rights and remedies about to be added to the already over-abundant and confusing pile.

flip side, however, there are many other property owners these days who do not hesitate to seize an opportunity to get goods or services at a discount, simply by not paying for them. And in between those two extremes, there are the vast majority of cases where the issues in dispute are simply a result of a series of genuine misunderstandings on both sides.

I am also not suggesting that the owner is not entitled to pursue his rights and enforce his remedies. If only he would do that. But resolving the underlying dispute is generally the last thing on

I really fear for the future of the small builders who do the high-end, architecturally-designed, residential building work. I don’t think the Government realise it, but coupled with the shift of responsibilities from Councils to the building trades and professionals, and the disciplinary powers of the Building Practitioners Board, these changes are going to drive more and more of these skilled craftsmen out of the market.

Interestingly we are on the verge of a building boom that will see supply and demand in the building sector radically reversed, so builders will have some bargaining power once again. But if they don’t use it, I believe they will find residential building an increasingly demoralising experience, and they will leave it to the group housing companies and residential divisions of the major construction companies. As a nation, we will be much the poorer for it.

Geoff Hardy has 35 years’ experience as a commercial lawyer and is the senior lawyer in the Auckland firm “Madison Hardy”.

He guarantees personal attention to new clients at competitive rates. His phone number is (09) 379 0700, fax (09) 379 0504, and e-mail geoff@madisonhardy.com. This article is not intended to be relied upon as legal advice.

9

Impulse FrameMaster-Li Framing Nailer

TM

®

The world’s number one framing nailer just got a whole lot better #B20543

$77700

Paslode Impulse Gas Technology Lithium-Ion Battery Technology • Charge in 1 hour, up to 6,000 nails per charge • Two lithium-Ion batteries included

EXCL GST

Low Tool Actuation Pressure • Reduces operator fatigue Tool-Free Depth of Drive Adjustment • Five depth of drive settings Suitable for 44 to 90mm Length Nails • Full range of 50 to 90mm nails in bright, galvanised, and stainless steel • Product Nail Guide attachment (B20540P) required to drive 44mm product nails • Suitable for 2.8 to 3.15mm Diameter Nails.

BONUS

Eagle Claw Nail Remover • Removes small trim nails without damaging timber • Hardened steel claws • Ideal for demolition

Nail Lock Out Bar • Eliminates blank tool firing, protects timber and tool.

ClearVue Polycarbonate Roofing

The look of glass at a fraction of the cost.

ClearVue’s high quality flat panel design will make the most of natural light, without the weight or cost of glass panels.

The polycarbonate panels are easily installed and require less structural support than heavy glass alternatives.

Paslode Eagle Claw and Beanie

TEMPORARY FLOOR PROTECTION Ram Board is a heavy-duty, temporary floor protection engineered for contractors. It lays out fast and is re-usable.

Ram Board is non-staining and utilises its Flex-Fiber™ and Spill Guard technology, impact resistant and breathable, allowing new floors to cure. It provides the perfect solution when protecting new or existing concrete, wood, tile, stone, linoleum, vinyl composition tile (vct), epoxy, and most other floor types.

BONUS

Available in 3700mm and 5100mm lengths in Clear or Grey.

1x FREE roll of Ram Tape with every 30m roll of Ram Board Contractor or 2 x 15m rolls of Ram Board Home Edition.

#RBH-15

$7900

EXCL GST

#RBC-30

$14900

EXCL GST

11

UNDERSTANDING CHANGES IN BRACING SPECIFICATION There have been numerous changes to the NZ Building code and standards over the past 12 months that have affected the Building Industry as a whole.

Whilst most of the changes have been well publicised a number have tended to slide by under the radar.

One change people may not be familiar with is the section of NZS 3604-Timber framed buildings that deals with bracing.

There are two main areas of change in regards to bracing.

Firstly the distribution rules have changed to encourage more even distribution of bracing throughout a structure.

And secondly the P21 (2010) protocol which is cited in NZS 3604 Timber framed buildings has been updated. The P21 method was updated to incorporate current best practice, remove ambiguities and align with the new loadings standard AS/NZS 1170.

From the 1st February 2012, all wall bracing unit ratings must be based on the new P21 (2010) protocol. While NZS 3604 shows us how to calculate bracing demand on a structure, it leaves it up to industry at large to supply methods of satisfying those demands. The change has meant that companies supplying systems for bracing have had to either, re-analyse, or re-test bracing panels in accordance with NZS 3604: 2011.

Make sure that you are specifying and using bracing systems which meet the latest requirements.

12

One trouble-free way to ensure plywood bracing meets these new standards is to specify Ecoply®. The EP bracing series has been specifically analysed in accordance with the new standard. The Ecoply™ EP bracing series simplifies the design and construction of bracing elements using plywood, by itself or in conjunction with GIB® plasterboard.

ECOPLY ® BRACING SPEC IFICATIONS: EP1

STRUCTURAL BRACING WITH PLYWOOD

3.3 ECoPLy® BRACING SPECI

FICATIoN – EP1

SINGLE SIDED STRuCT

uRAL PLyWooD BRACE

Specification No.

Minimum Wall Length

EP1

Lining Requirements

0.6 m

7 mm Ecoply® or Ecoply

BUs/m Wind

Barrier one side

BUs/m Earthquake

125

130

Framing Wall framing must comply

Fastening centres

with:

• NZBC B1 - Structure: AS1 Clause 3 Timber (NZS 3604:2011) • NZBC B2 - Durability : AS1 Clause 3.2 Timber (NZS 3602) Framing dimensions and height are as determine d by the NZS 3604 stud and top plate tables for load bearing and non load bearing walls.

Kiln dried verified structural grade timber must be used. Machine stress graded timber, such as Laserframe ®, is recomme nded.

Fasteners are placed at 150 mm centres around the perimeter of each sheet and 300 mm centres to intermedi ate studs.

Where more than one sheet forms the brace element each sheet must be nailed off independently.

Bottom plate fixing Use GIB Handibrac hold-dow n connections at each end of the bracing element. Refer to manufacturer installatio n instructions supplied with the connecto rs for correct installatio n instructions and bolt types to be used for either concrete or timber floors.

Within the length of the bracing element, bottom plates are fixed in accordance with the requirements of NZS 3604. ®

Lining

7 mm Ecoply fixed with 50 x 2.8 mm nails at 150 mm centres to perimeter of bracing element at no less than 7 mm from sheet edge and at 300 mm centres to intermediate studs ®

GIB HandiBrac® Hold Down

One layer of 7 mm Ecoply plywood or Ecoply Barrier fixed directly to framing or over cavity battens. If part sheets are used, ensure nailing at required centres is carried out around the perimeter of each sheet or part sheet. A 2-3 mm expansion gap should be left between sheets. ®

Fastening the Ecoply ® Fasteners Fasten with 50 x 2.8 mm galvanised or stainless steel flat head nails for direct fix, or 60 x 2.8 mm over cavity battens.

Place fasteners no less than 7 mm from sheet edges.

Fasteners for H3.2 CCA treated Ecoply Where fasteners are in contact with H3.2 CCA treated timber or plywood, fasteners shall be a minimum of hot dip galvanised.

In certain circumstances stainless steel fasteners may be required. Refer to table 8 of the Ecoply Specificat ion and Installation Guide for these circumstances and further fastener selection advice.

Where stainless steel nails are required, annular grooved nails must be used.

Ecoply Bracing Systems are designed to meet the requirements of the New Building Code and have Zealand been tested and analysed using the P21 method referenced in NZS 3604:2011 listed as an acceptable solution B1/AS1 Structure. Testing carried out using Ecoply was and Laserframe SG8 timber framing manufactured by ®

18

CHH WoodproduCts

Carter Holt Harvey Limited trading as CHH Woodprodu cts New Zealand, and GIB® products manufacture d by Winstone Wallboards Ltd. Substituting materials may compromise performance of the system. GIB® and GIB HandiBrac® are registered trade marks of Fletcher Building Holdings Ltd.

| ECoply | 0800 326 759 | www.chhw oodproducts.co.nz ®

In alignment with recent changes to NZS 3604:2011 Timber Framed Buildings the SP Bracing Series no longer meets the requirements of the new standard from the 1st February 2012 and should not be used. As such it has been removed from all CHH Woodproducts bracing specification material effective from the 1st January 2012.

Any Ecoply branded panel may be used for bracing as long as it is of a 7 – 12 mm thickness, is treated for the specific application in accordance with NZS 3602 and fixed in accordance with Ecoply bracing specifications.

ECOPLY EP bracing series benefits: • Higher bracing performance per metre than old SP elements • Reduced number of element types and simplified naming system • Single sided and double sided bracing elements • Special EPGs bracing element design for where plywood cladding comes to soffit line within 300mm of top plate • A single type, GIB® Handibrac, hold-down for all bracing elements • Simplified construction • Single page specifications for each bracing element type

Bracing values and specifications are specific to Ecoply branded structural plywood and cannot be used with any other plywood brand no matter how similar they may appear.

For more information on the new P21 (2010) protocol please view the Department of Building and Housing (DBH) website: http://www.dbh.govt.nz/bc-update-127 Ecoply® EP bracing specifications can be found at www.chhwoodproducts.co.nz

Specification No.

Minimum Wall Length

Lining Requirements

BUs/m Wind

BUs/m Earthquake

EPI

0.6m

7mm Ecoply® or Ecoply Barrier one side

125

130

0.6m

7mm Ecoply or Ecoply Barrier each side

140

150

7mm Ecoply® or Ecoply Barrier one side and 10mm GIB® Standard plasterboard other side

100

115

150

150

7mm Ecoply® or Ecoply Barrier one side and 10mm GIB® Standard plasterboard other side

100

115

150

120

EP2

0.4m EPG 1.2m 0.4m EPGs 1.2m

®

Note: Plywood side of element must be a maximum of 300mm below top plate.

THE FUTURE OF DECKING IS HERE FUTUREWOOD® is An all-in-one, environmentally sustainable and virtually maintenance free composite deck Now you can move away from the common rainforest timber deck with all of its associated environmental concerns and maintenance issues by using Futurewood composite decking.

Futurewood is made from recycled HDPE (industrial waste and some post-consumer plastic waste) sawdust and discarded rice husks, making it one of the most environmentally friendly composite decking options available.

Futurewood composite decking looks stylish, is cost effective and easy to install with the optional concealed fixing system giving the deck an added touch of class.

Futurewood decking is available in three colours, Walnut, Mahogany and Slate Grey. It comes as a standard 138mm x 23mm x 5400mm board.

So for a better looking, longer lasting and more environmentally sustainable deck ask your ITM store about Futurewood composite decking.

What’s more, it comes with a 15 year warranty against any rotting or white ants/termite attack.

13

BATHROOMS

CASCADE ACRYLIC SHOWERS

• Free upgrade to 1900mm high door set • Waste, glue and sealant pack included • Pivot door with drip channel • Splashsafe full length door seal • Frame reversible • 4mm safety glass to NZ standards • 5 year warranty • Made in New Zealand

EXCLUSIVE to ITM

FROM

$86900

Riviera Acrylic Shower

CEZANNE SHOWER • Space saving sliding round doorset • 6mm safety glass door complying to NZ standards • Magnetic door closure • Enclosure height 1970mm • 5 year warranty #0C9M009904 Moulded 9x9 RND #0C9F009904 Flat 9x9 RND

$120000 $130000 EXCL GST

NEW 2012/13 Catalogue out now

Large range of shower sizes in Neo, 2 and 3 sided options.

EXCL GST

EXCL GST

• Available in chrome or white • AquaCHECK corner drain system to prevent water damage • 1850mm high door and returns • Magnetic door closure • Waste, glue and sealant pack included #RIV915rndacfw #2RIV915RND FW

Free $50 Hunting & Fishing Voucher

$86900

GAUGUIN SPA BATH

GAUGUIN BATH

• 1675 x 780 x 500mm acrylic bath • 109 litre working water capacity • Includes heated pump, electronic control and wooden support frame • Contoured lumbar support and arm rests • Spa includes four chrome jets #0544002016

• 1675 x 780 x 500mm acrylic bath • 109 litre working water capacity • Anti slip tread pattern on floor • Contoured lumbar support and arm rest # 0144000006

$149900 NE

Kahlo Bath

EXCL GST

• • • • • •

Two size acrylic bath options 1675mm or 1800mm • Spa includes heated pump, electronic control and wooden support frame 1675 = 135 Litre / 1800= 170 Litre Bath, spa or shower over bath package options • Factory fitted upstands are recommended when bath is positioned against a wall Contoured arm rests (pictured bottom right) Wooden support frame available • Made in New Zealand Spa includes six (1675) or eight (1800) chrome jets, upgradable to whisper jets or whisper/mini combo

Size Options 1675x800x480 1800x800x480

Upstand Options No upstands 1 sided 2 sided 3 sided

Spa Options Standard spa Whisper jets Whisper/Mini jets Hydrotherapy

FREE ITM BUILDERS GLOVES WHEN YOU SPEND $200 OR MORE ON BATHROOM PRODUCTS FEATURED ON THIS PAGE 14

Tapware and accessories not included.

$34900

EXCL GST

W

EXCL GST

BATHROOMS

W

Grafton Vanity

NE

• Concealed opening system • Drawer only cabinet style • Available in three cabinet configurations • Complementing tower available • Cabinet made in New Zealand

• Introduced in July 2012 • Semi recessed 75mm thick polymarble top • 750, 900, 1200 and 1400mm double bowl sizes available • Soft closing drawers

Grafton 900mm single drawer white gloss model shown. Tapware not included.

Size Options 750mm 900mm 1200mm 1400mm Double

Configuration Options Double Drawer Floor Standing Double Drawer Wall Hung Single Drawer

STATESMAN DOUBLE DRAWER VANITY

STATESMAN VANITY

• Slimline vitreous china top with integrated overflow • Soft closing drawers • Melamine cabinet with PVC capped edges #7SDFM000702SV – 750mm #7SDFM001202SV – 1200mm

• Rectangular acrylic top • Soft closing doors and drawers • Made in New Zealand #7SWM000922 - 900mm

$75900

EXCL GST

$112000

EXCL GST

$49900

EXCL GST

Colour Options White Gloss, Charred Oak, Dark Oak, Basalt, Salt Wash, Silva Strata

900mm model shown.

Tapware not included.

#7SWM001222 - 1200mm

$53900

EXCL GST

FREE AQUALINE VANITY WASTE

FREE AQUALINE VANITY WASTE

PRIMUS SINK MIXER

PRIMUS SHOWER MIXER

• WELs Rating: mains - 3 Star 8L/min • Low/Unequal - 3 Star 8.5L/min • 5 year warranty #PMX1

• Suitable for mains or unequal low pressure • 5 year warranty #PSM5

$6999

$7999

PRIMUS BASIN MIXER

PRIMUS SLIDE SHOWER

EXCL GST

• WELs Rating: mains - 4 Star 7.5L/min • Low/Unequal - 3 Star 9L/min • High quality all metal construction • 5 year warranty #PMB5

$6999

EXCL GST

EXCL GST

• Suitable for all pressures • 2 year warranty • Monojet • All pressures #PSL8

$6999

EXCL GST

FREE ITM BUILDERS GLOVES WHEN YOU SPEND $200 OR MORE ON BATHROOM PRODUCTS FEATURED ON THIS PAGE 15

watch your waste

A Division of Transpacific Industries Group (NZ) Ltd

Order waste services direct from ITM and charge it to your ITM account

BIN TYPE

SIZE 3.0 cubic metre open top gantry bin (3.3L x 1.5W x 0.6H)

USE Hardfill*1 - Up to 3 tonnes General waste*2 - Up to 1.5 tonnes

9.0 cubic metre open top gantry bin (3.3L x 1.5W x 1.8H)

General waste*2 - Up to 1.5 tonnes

10.0 cubic metre open top smartskip bin (4.4L x 2.2W x 1.4H)

General waste*2 Up to 1.6 tonnes

15.0 cubic metre open top smartskip bin (4.4L x 2.4W x 1.8H)

General waste*2 Up to 2.5 tonnes

Port-O-Let Model 88 (Waterless) (2.1H x 1.2W x 1.2D)

ASK INSTORE FOR AN OBLIGATION FREE QUOTE SOME SERVICES ARE NOT AVAILABLE IN ALL AREAS. FOR OTHER BIN SIZES - PLEASE ASK INSTORE SPECIAL NOTES: 1. Hardfill/Cleanfill includes concrete, asphalt, masonry blocks, bricks, rocks, soil & clay. 2. General waste excludes hardfill/cleanfill and hazardous waste such as explosive, noxious, illegal or dangerous materials. 3. See your local ITM store for more details.

FROM MANSIONS To FALES “It was very bush, very ad-lib and my apprentices thought *!!#!*.

But helping out after the Samoa tsunami was one of the biggest challenges and most rewarding experiences I’ve ever had.”

Three years ago, Registered Master Builder Allister Saville from Arrowtown responded to an out of the blue email from ITM asking for help following the Samoa Tsunami. Here are his recollections.

hoped, which all came down unfortunately to a lack of organisation.

“But we got stuck in and after two weeks, we had built eight houses.

“We helped with one house in particular; this guy had lost all his children. When we went back this year, we saw him and it was such a tremendous experience.

The first view of the devastation First impressions “I was one of seven who went over roughly three weeks after the tsunami. We went to the village of Lepa and the devastation was laid out all around us.

There was literally nothing left in the lower part of the village.

“We also brought a generator donated by ITM and presented it at the church and it was very emotional.

“What my guys got out of it was amazing. They all left there enriched. We were blown away by the people…they’re just lovely people. They have a tight family network and the way they support each other, a lot of people could learn from that in our society

“Because there was going to be up to 40 volunteers there every week for the next couple of years, we set up a shower and toilet block straight away and built a rudimentary frame and truss plant. It was all pretty ad-lib…pretty bush…

“We slept on mattresses on the floor of the church hall and the village people fed us the whole time and they gave us a hand with the rebuilding, but a lot of them were totally shell shocked. Many had lost their families and they had all lost their homes.

Presenting the generator Why did you do it?

“It’s funny, I don’t know, I’m not religious, maybe I was just going through a soft spot but I thought, yes this something I can do, I can use my skills.

“I could donate clothes or money, but this way I could be sure that my contribution would get to the people who needed it, and after being there, I’m glad I made that decision.

Fale build in progress “We managed to put together a good group of guys – chippies, plumbers, electricians and labourers. But building upwards of 400 fales, it was huge task and I knew we would have to come back.”

Getting stuck in “I took two of my apprentices back the following year and some of my subbies came too. When we got there, they hadn’t made as much progress as I’d

“When I asked the apprentices to come for the second visit, they were all pretty keen. But a week into it, they thought *!!#!*, what have you done to us! It was really hot and it was tough work.

“But I saw those boys grow from apprentices to men in that time, and that was tremendously rewarding for me.”

Taking a well-earned break 17

7.0 Nights Saturday 0pm on TV 3

AUGUST ACTION

4th August Anglers Paradise Part 2 Packs of sharks are devouring all of the fish Matt and the team hook into, so a local Tahitian guides them to a remote atoll a further 80 miles away where the sharks are scarce and the fish are huge!

11

th

August

Trailer Boat - Game Fishing Waihau Bay The blue marlin are biting off East Cape, so Matt hitches on the boat and takes his apprentice Jake to Waihau Bay to have a go at catching his first marlin.

Jake gets some lessons he’ll never forget.

SIGN UP TODAY FOR BUILDING BUSINESS

AND EARN SKILLS MAINTENANCE POINTS Its quick and easy to subscribe online www.itm.co.nz/subscribe

!

18th August The Kayak Comp Day 1 Matt is new to kayak fishing, and he’s never fished the South Taranaki coast. So it’s the perfect place for him to go and compete with 200 kayak fishing enthusiasts. Don’t be fooled into thinking that Kayak fishers are disadvantaged, the size and number of the fish caught is truly impressive!

25th August The Kayak Comp Day 2 There are 200 anglers competing for honors in a kayak fishing comp, and it seems none of them want to share any information or local knowledge with Matt. In danger of a severe ass-whooping, Matt goes back to basics and uses big baits in the shallows to target big snapper.

6

Issues year per

1 point

per issue

CEMENT/blades

MULTICRETE

Fastcrete

• General concrete projects not requiring fast setting times • Recommended Uses: Steps, slabs, footings, pathways, driveways, deck posts, signage, mowing strips, garden edging, fence posts #GPC025 - 25kg

• For general concrete projects requiring very fast setting times with low structural requirements • Sets within 15 minutes #FSC025

$849

EXCL GST

#GPC040 - 40kg

$1299

EXCL GST

$949

EXCL GST

DUO Pro Blades

4x4 Explorer Blades

• 12mm high laser welded segments • General purpose • Patented split segment technology for greater cutting speed and longer life #DUO11522 - 115mm

• Multi-purpose blades for use on concrete, granite, steel and asphalt • Depth gauge arrows #D4X423025 - 230mm

$2999

$7599

EXCL GST

#DUO12522 - 125mm

$3499

EXCL GST

EXCL GST

#DUO18025 - 180mm

$4599

EXCL GST

#D4X430025 - 300mm

#D4X440025 - 400mm

$20900 $24900 EXCL GST

EXCL GST

MAKE A TIME TO See A SPECIALIST NORTHLAND

Thomsons ITM Building Centre Te Rapa 07 849 3674 Thomsons ITM Building Centre Whatawhata 07 829 8518 Timmo’s ITM Building Centre Te Awamutu 07 871 7545 Triangle Timber ITM Building Centre Tokoroa 07 886 6611 Whakatane ITM Building Centre 07 307 0031

Crighton ITM Building Centre Seaview 04 568 3896 Northpac ITM Building Centre Newlands 04 478 5489 Parapine ITM Building Centre Upper Hutt 04 527 6800 Tawa ITM Building Centre 04 232 5999 Tumu ITM Building Centre Masterton 06 370 6060

AUCKLAND

COROMANDEL

NELSON/MARLBOROUGH

Dargaville ITM Building Centre 09 439 8730 Far North ITM Building Centre 09 406 0048 Whangarei ITM Building Centre 09 437 9420 Waipu ITM Building Centre 09 432 0203 Albany ITM Building Centre 09 415 6889 Dayle ITM Building Centre Avondale 09 828 9791 Dysart Timbers ITM Building Centre Drury 09 294 9410 Dysart Timbers ITM Building Centre Glen Innes 09 521 3609 Hillside ITM Building Centre Glenfield 09 443 8101 MacClures ITM Building Centre Henderson 09 836 0088 Mahia ITM Building Centre Takanini 09 267 0234 Matakana ITM Building Centre 09 422 7525 Pinepac Kumeu ITM Building Centre 09 412 8148 Pinepac Swanson ITM Building Centre 09 832 0209 Pinepac Whenuapai ITM Building Centre 09 416 8164 Smith Timber ITM Building Centre East Tamaki 09 274 4942 Tuakau ITM Building Centre 09 236 8226 Waiuku ITM Building Centre 09 235 7289 Weck's ITM Building Centre Patumahoe 09 236 3684

WAIKATO/BAY OF PLENTY

Acorn ITM Building Centre Riverlea 07 856 6789 Cambridge ITM Building Centre 07 827 0953 Katikati ITM Building Centre 07 549 0689 Matamata Post and Rails ITM Building Centre 07 888 8189 Opotiki ITM Building Centre 07 315 5984 Oregon ITM Building Centre Mount Maunganui 07 575 3126 Oregon ITM Building Centre Papamoa 07 542 9005 Oregon ITM Building Centre Te Puna 07 552 5770 OTC Timber ITM Building Centre Otorohanga 07 873 8079 Rotoma ITM Building Centre Rotorua 07 347 7023 Taupo ITM Building Centre 07 378 9899 Tauranga ITM Building Centre 07 541 1232

Bargain Boards ITM Building Centre Kopu 07 868 9829 Barrier ITM Building Centre 09 429 0466 Coromandel Timber ITM Building Centre 07 866 8848 Pauanui ITM Building Centre 07 864 8579

CENTRAL NORTH ISLAND

Hometown ITM Building Centre Foxton 06 363 8049 Manawatu ITM Building Centre Palmerston North 06 356 9490 New Plymouth ITM Building Centre 06 758 8939 Rural ITM Building Centre Feilding 06 323 3400 Rural ITM Building Centre Marton 06 327 5458 Standard Timber ITM Building Centre Stratford 06 765 7800 T. Braithwaite Timbers ITM Building Centre Taumarunui 07 895 6881 Tumu ITM Building Centre Dannevirke 06 374 4260 Turangi ITM Building Centre 07 386 5736 Waitara ITM Building Centre 06 754 8822

HAWKES BAY

Total ITM Building Centre Hastings 06 879 7850 Tumu ITM Building Centre Gisborne 06 868 9599 Tumu ITM Building Centre Hastings 06 873 0999 Tumu ITM Building Centre Havelock North 06 872 7100 Tumu ITM Building Centre Napier 06 872 6222 Wairoa ITM Building Centre 06 838 7332

WELLINGTON/WAIRARAPA

Building World ITM Building Centre Wainuiomata 04 939 4486 Crighton ITM Building Centre Greytown 06 304 7193 Crighton ITM Building Centre Levin 06 368 4057 Crighton ITM Building Centre Paraparaumu 04 298 9726

Blenheim ITM Building Centre 03 578 3049 Havelock ITM Building Centre 03 574 1018 Kaikoura ITM Building Centre 03 319 5447 Motueka ITM Building Centre 03 528 7254 Nelson ITM Building Centre 03 548 5487 Picton ITM Building Centre 03 573 6888 Takaka ITM Building Centre 03 525 8222

CANTERBURY/WEST COAST

Basher's ITM Building Centre Amberley 03 314 8311 Darfield ITM Building Centre 03 318 7474 Dyers Road ITM Building Centre Bromley 03 384 4111 Geraldine ITM Building Centre 03 693 9397 Greymouth ITM Building Centre 03 7680441 Hamptons ITM Building Centre Waltham 03 374 3333 Helmack ITM Building Centre Ashburton 03 307 0412 Hillside ITM Building Centre Hornby 03 349 973 Kaiapoi ITM Building Centre 03 327 8829 Leeston ITM Building Centre 03 324 3300 McMullan Timber ITM Building Centre Hokitika 03 755 8519 Newble Timber ITM Building Centre Rangiora 03 313 4862 Timaru ITM Building Centre 03 688 8074

DUNEDIN/OTAGO/SOUTHLAND

E H Ball ITM Building Centre Invercargill 03 218 3787 Fraser Hardware ITM Building Centre Balclutha 03 418 0170 Garden Place ITM Building Centre Mosgiel 03 489 8885 Southbuild ITM Building Centre Winton 03 236 6055 Southern Lakes ITM Building Centre Cromwell 03 445 0081

For your nearest ITM Store phone 0800 for itm - www.itm.co.nz PRODUCTS ON PROMOTION: All prices exclude GST. Prices are valid from 1st August - 16th September 2012, unless specified otherwise. Some products may not be available in all ITM stores, but can be ordered in for customers. FREE ITM BUILDERS GLOVES CONDITIONS: Applies to purchases made between 1st August 16th September 2012 or while stocks last. Please note that the $200 (excl GST) qualifier for the ITM BUILDERS GLOVES applies to each supplier’s product featured and cannot be made up of smaller amounts spent on individual supplier’s products e.g. Customers will qualify for a giveaway if they purchase $200 of Hitachi products, NOT if they purchase $150 of Hitachi power tools and $50 on Marley products. Purchases must be made on one invoice/account. Offer is limited to two per customer.

All prices exclude GST.

ly while stocks last StrictStrictly while stocks last