BUILDING SCIENCE AND SERVICES

Assignment I Building Science and Services BLD62304103247

Karenina Devi Yuwono 0340802

SITE CONTEXT Current electrical wiring

SITE ISSUES

1. AIR CONDITONER PLACEMENT

The air conditioner position as in the current ceiling plan, should not be installed in the head and end of the bed. This is very important because it is the position where air is released directly to the body and head which may cause health problems.

If the air conditioner is not cleaned for a long time, the air blown out from the air conditioner will have moisture and germs as well. Which is one part that causes the respiratory system to malfunction. You may get cold or allergy easily.

2. EXCESSIVE HORSEPOWER OF THE AIRCONDITIONER

Currently, the horsepower of the AC in the current room is 1.5, that explains why the room gets unecessarily too cold when using the AC. The horspepower might be too big for the total heat load of the room, which will be calculate using the 7 step of the HVAC calculation in the folowing report.

3. INSUFFICIENT PLACEMENT and WATTAGE OF LIGHTING

The placement of the lighting in the current bedroom are ineffective and not comforting. When using

the working table, the shadow of ourself is blocking the lights that penetrate from the

center of the ceiling, and that's becoming an issue because I spent most of the time of my day sitting and doing works on the working table.

Another issue that come to the surface is that the wattage of the ceiling light that are too big and not used efficiently for the room therefore, some replacement of thelightings are required

SITE CONTEXT New proposed electrical wiring

SOLUTIONS

1. POSITION REPLACEMENT FOR AIR CONDITONER

The installation position should be in the long wall position. So that the cold air can distribute to the left and right of the room evenly. And not installing air conditioners on all electrical devices because while the air conditioner is working often have water problems with air dripping. If there is electrical equipment at the bottom will damage electrical equipment. It can cause an electric shock accident.

The most suitable position for installation in the bedroom is the side wall that is perpendicular to the bed. The wind direction from the machine blow across the body while sleeping. It may be installed slightly towards the end of the bed and will help reduce the risk of allergies or the respiratory system.

2. BRINGING DOWN THE HORSEPOWER OF THE AIRCONDITIONER HVAC Calculation

As we can see on the above 7 steps of HVAC calculation that the based on the total heat load, the AC unit required are only 0,8 which are rounded to 1 Horsepower. This explains the room is too cold while operating the air conditioner. It will improve our sleeping/activities qualities as weel as reduce down the energy used by half

3.

RELOCATE THE LIGHTING POSITIONS AND THE WATTAGE

To optimizing the lighting used, we must know which position are the

most

effective.

Lights

should

be

positioned

around

the

perimeter of the room order for the lights to be able to every sides and corner of the space. For this floor plan, I figured out that we only need 2 pieces of downlight lights because of the size of the room

As we can see on the new ceiling plan that the placement of both recessed light are placed right in front of the closet and near the working desk & bed. This coveres up the majority part of the bedroom

Another solutions to the issue regarding the lights on the working desk, I came up to the solution which

solving

the

problem

as

well

as

adding

another features to bedroom. Track lighting works best in a

minimalist bedroom with high ceilings. It

will help to decorate the interior of the bedroom.

Unlike another light that the light fixtures are fixed to the ceiling or wall, with track lighting fixtures, that problem is eliminated as the lights can be moved to suit your tastes.The users can move it toward the working desk as well as towards the bed for night reading, so it will have a double function. Also, with the distance from the light to the objects, it allows the light to difuse and become softer while pointing towards the object and will not likely to cause eye strain.

Questions of the day !

Why not using regular desk lamp? that if we are exposed to direct

Studies have shown

lighting for too long, it

can actually damage our eyes by increasing the risk of eye diseases. It cuts down on glare which is one of the main factors causing tired eyes and eye strain.

ENERGY USED CALCULATIONS

As shonw on the table above, the energy used for old design per month are

341,34 kW,

resulting the total bill to be cost RM 136,50. It is mostly because of the samsung air conditioner and LED ceiling light.

After solving the issues, we can see on the table of energy used for new design that changing the air conditioner horsepower and lighting wattage affect the monthly bill to RM 104,10.

BILL OF QUANTITIES

L1

L2

V1

INTERIOR PERSPECTIVE VIEW

rendered Interior perspective. with new lighting and VAC position and features

CONCLUSION

Although it may sounds simple, choosing the right

lighting and VAC area bit tricky and crucial

because we have to consider all posibilities that might be faced later. The comfort of the user are also important in this matter because they are the one who experiencethe space.

By conducting this project, I have learned a lot about how to choose the perfect lighting and ventilation while considering the cost and energy used,

Assignment II Building Science and Services BLD62304103247

Karenina Devi Yuwono 0340802

Room 2

Room 1

Toilet 1

Toilet 2

Room 3

Living room

DN

Room 4

Dining Area

Kitchen

Floor plan Scale 1 : 100 WALL 3

WALL 5

(9,8 ft)

(4,9 ft)

3000

1500

0051

)tf 9,4(

4 LL A W

0033

Room 4

)tf 8,01(

WALL 1

0033

1 LL A W

)tf 8,01(

Label

Facing outside with attached window

WALL 2

Facing outside

WALL 3

Facing room 3

WALL 4

Facing Living room

WALL 5

Facing Living room with attached door

4500 (14,76 ft)

WALL 2 Room 4 (not to scale)

II A. Heat transfer Calculation

WALL 1 (facing outside)

Area : Window

= 4,6 ft x 5,18 ft = 25,38 ft2

Brick wall = Total wall - Window

= (10,8 ft x 9,18 ft) - (4,6 ft x 5,18 ft) = 99,14 ft2 - 25,38 ft2 = 73,76 ft2

R-value Brick.

= 0.2 x Thickness = 0.2 x 5.9 in = 1,18

Window = R Interior film + R single pane = 0.68 + 0.91 = 1.76

7 a.m.

T = Outside temp - Inside temp = 25 C - 21 C = 77 F - 71 F = 6 F A. Window

= 25,38 ft2

A. Brick wall = 73,76 ft2 R Window

= 1.59

R Brick wall = 1,18

Area x

T

Q Brick wall =

Area x Q Window

R-Value

R-Value

73,76 ft2 x 6 F =

T

=

25,38 ft2 x 6 F =

1,18

= 375,05 BTU / hr

1,59

= 95,77 BTU / hr

Total heat transfer = Q brick wall + Q Window = 375,05 BTU/hr + 95,77 BTU/hr

= 470,82 BTU/hr

12 p.m.

T = Outside temp - Inside temp = 36 C - 21 C = 98 F - 71 F = 27 F A. Window

= 25,38 ft2

A. Brick wall = 73,76 ft2 R Window

= 1.59

R Brick wall = 1,18

Area x

T

Area x

Q Brick wall =

Q Window

T

=

R-Value

R-Value

73,76 ft2 x 27 F

25,38 ft2 x 27 F

=

= 1,18

1,59

= 1687,72 BTU / hr

= 430,98 BTU / hr

Total heat transfer = Q brick wall + Q Window = 1687,72 BTU/hr + 430,98 BTU/hr

= 2118,70 BTU/hr

5 p.m.

T = Outside temp - Inside temp = 30 C - 21 C = 86 F - 71 F = 15 F A. Window

= 25,38 ft2

A. Brick wall = 73,76 ft2 R Window

= 1.59

R Brick wall = 1,18

Area x

T

Q Brick wall =

Area x Q Window

R-Value

R-Value

73,76 ft2 x 15 F =

T

=

25,38 ft2 x 15 F =

1,18

= 937,62 BTU / hr

1,59

= 239,43 BTU / hr

Total heat transfer = Q brick wall + Q Window = 937,62 BTU/hr + 239,43 BTU/hr

= 1177,05 BTU/hr

WALL 2 (facing outside)

Area : Brick wall

= 14,76 ft2 x 9,18 ft2 = 135,49 ft2

R-value Brick wall

= 0.2 x Thickness = 0.2 x 5.9 in = 1,18

7 a.m.

T = Outside temp - Inside temp = 25 C - 21 C

Area x

T

Q Brick wall =

= 77 F - 71 F

R-Value

= 6 F

135,49 ft2 x 6 F =

A. Brick wall = 135,49 ft2

1,18

R Brick wall = 1,18 = 688,93 BTU / hr

Total heat transfer = Q brick wall = 688,93 BTU / hr

12 p..m.

T = Outside temp - Inside temp = 36 C - 21 C

Area x

T

Q Brick wall =

= 98 F - 71 F

R-Value

= 27 F 135,49 ft2 x 27 F =

A. Brick wall = 135,49 ft2

1,18

R Brick wall = 1,18

= 3100,19 BTU / hr

Total heat transfer = Q brick wall = 3100,19 BTU / hr

5 p..m.

T = Outside temp - Inside temp = 30 C - 21 C

Area x

T

Q Brick wall =

= 86 F - 71 F

R-Value

= 15 F 135,49 ft2 x 15 F A. Brick wall = 135,49 ft2 R Brick wall = 1,18

= 1,18 = 1722,33 BTU / hr

Total heat transfer = Q brick wall = 1722,33 BTU / hr

WALL 3 (facing other room)

The AC in Room 3 is rrarely turned on,that's why the temperature is on range 25C - 26C

Area : Brick wall

= 9.8 ft2 x 9,18 ft2 = 89,96 ft2

R-value Brick wall

= 0.2 x Thickness = 0.2 x 5.9 in = 1,18

7 a.m.

T = Outside temp - Inside temp = 24 C - 21 C

Area x

T

Q Brick wall =

= 75 F - 71 F

R-Value

= 4 F

89,96 ft2 x 4 F =

A. Brick wall = 89,96 ft2

1,18

R Brick wall = 1,18 = 304,94 BTU / hr

Total heat transfer = Q brick wall = 304,94 BTU / hr

12 p..m.

T = Outside temp - Inside temp = 26 C - 21 C

Area x

T

Q Brick wall =

= 80 F - 71 F

R-Value

= 9 F 89.96 ft2 x 9 F =

A. Brick wall = 135,49 ft2

1,18

R Brick wall = 1,18

= 686,13 BTU / hr

Total heat transfer = Q brick wall = 686,13 BTU / hr

5 p..m.

T = Outside temp - Inside temp = 25 C - 21 C

Area x

T

Q Brick wall =

= 77 F - 71 F

R-Value

= 6 F 89.96 ft2 x 6 F A. Brick wall = 135,49 ft2 R Brick wall = 1,18

= 1,18 = 457,42 BTU / hr

Total heat transfer = Q brick wall = 457,42 BTU / hr

WALL 4 (facing living room)

There are no air conditioner in the living room, that's why the temperature is on range 26C - 30C

Area : Brick wall

= 10,8 ft2 x 9,18 ft2 = 99,14 ft2

R-value Brick wall

= 0.2 x Thickness = 0.2 x 5.9 in = 1,18

7 a.m.

T = Outside temp - Inside temp = 26 C - 21 C

Area x

T

Q Brick wall =

= 80 F - 71 F

R-Value

= 9 F

99,14 ft2 x 9 F =

A. Brick wall = 99,14 ft2

1,18

R Brick wall = 1,18 = 756,15 BTU / hr

Total heat transfer = Q brick wall = 756,15 BTU / hr

12 p..m.

T = Outside temp - Inside temp = 30 C - 21 C

Area x

T

Q Brick wall =

= 87 F - 71 F

R-Value

= 16 F 99,14 ft2 x 16 F =

A. Brick wall = 99,14 ft2

1,18

R Brick wall = 1,18

= 1344,27 BTU / hr

Total heat transfer = Q brick wall = 1344,27 BTU / hr

5 p..m.

T = Outside temp - Inside temp = 28 C - 21 C

Area x

T

Q Brick wall =

= 84 F - 71 F

R-Value

= 13 F 99,14 ft2 x 13 F A. Brick wall = 99,14 ft2 R Brick wall = 1,18

= 1,18 = 1092,22 BTU / hr

Total heat transfer = Q brick wall = 1092,22 BTU / hr

WALL 5 (facing living room)

There are no air conditioner in the living room, that's why the temperature is on range 26C - 30C

Area : Door

= 2,9 ft x 6,8 ft = 19,72 ft2

Brick wall = A Total wall - A Door = (4,9 ft x 9,18 ft) - (2,9 ft x 6,8 ft) = 44,98 ft2 - 19,72 ft2 = 25,26 ft2

R-value Brick.

= 0.2 x Thickness = 0.2 x 5.9 in = 1,18

Door

= 2,17 (with thickness 1 3/4")

7 a.m.

T = Outside temp - Inside temp = 26 C - 21 C = 80 F - 71 F = 9 F A. Door

= 19,72 ft2

A. Brick wall = 25,26 ft2 R Door

= 2,17

R Brick wall = 1,18

Area x

T

Q Brick wall =

Area x Q Door

R-Value

R-Value

25,26 ft2 x 9 F =

T

=

19,72 ft2 x 9 F =

1,18

= 192,66 BTU / hr

2,17

= 81,78 BTU / hr

Total heat transfer = Q brick wall + Q Door = 192,66 BTU/hr + 81,78 BTU/hr

= 274,44 BTU/hr

12 p.m.

T = Outside temp - Inside temp = 30 C - 21 C = 87 F - 71 F = 16 F A. Door

= 19,72 ft2

A. Brick wall = 25,26 ft2 R Door

= 2,17

R Brick wall = 1,18

Area x

T

Area x

Q Brick wall =

Q Door

T

=

R-Value

R-Value

25,26 ft2 x 16 F

19,72 ft2 x 16 F

=

= 1,18

2,17

= 342,50 BTU / hr

= 145,40 BTU / hr

Total heat transfer = Q brick wall + Q Door = 342,50 BTU/hr + 145,40 BTU/hr

= 487,90 BTU/hr

5 p.m.

T = Outside temp - Inside temp = 28 C - 21 C = 84 F - 71 F = 13 F A. Door

= 19,72 ft2

A. Brick wall = 25,26 ft2 R Door

= 2,17

R Brick wall = 1,18

Area x

T

Q Brick wall =

Area x Q Door

R-Value

R-Value

25,26 ft2 x 13 F =

T

=

19,72 ft2 x 13 F =

1,18

= 278,28 BTU / hr

2,17

= 118,13 BTU / hr

Total heat transfer = Q brick wall + Q Door = 278,28 BTU/hr + 118,13 BTU/hr

= 396,41 BTU/hr

Conclusion

Time

Wall 1

Wall 2

Wall 3

Wall 4

Wall 5

7 a.m.

470,82

688,93

304,94

756,15

274,44

12 p.m.

2118,70

3100,19

686,13

1344,27

487,90

5 p.m

1177,05

1722,33

457,42

1092,22

396,41

Total

3766,57

5511,43

1448,49

3192,64

1158,75

(Unit : BTU/hr)

Based on the calculation and table above, the wall which have the highest Q is Wall 2 with 3100,19 BTU/hr at 12 p. m. The q value is much affected by the area. But due to the fact that Wall 2 is nealy 2 times bigger than Wall 1, it can be concluded that if both of them have the same area, then Wall 1 with 2118,70 BTU/hr, will have the highest heat absorption eventhough the Q value of the Wall 2 is higher .

II B. Green Insulation Product Development

1 .Product Description : A

multifunction

transmission

as

cushion well

as

insulator

reducing

to

the

reduce

posibilty

heat of

transfer,

person

sound

getting

hurt

because of the wall . Suitable for all walls except bathroom walls 2. Product Dimension : 350 cm x 24 cm x 2,5 cm 3. Product Weight

: 50 grams

4. Features

:

Can be used as thermal insulation, sound insulation, as well as wall protector Given the flexibility to choose which color is facing the desired side.

Lightweight and durable materials.

Easy installation and removal.

Using sandwich method that resulcting in the quick drop of temperature and can restrain the heat transfer from both sides.

Side 2

3 5 0

Side 1

M M

A T T A C H E D

M M

0 4 2

L O O P

A T T A C H E D H O O K

F A S T E N E R

S E P E R A T E D H O O K

&

D O U B L E T A P E

T O

L O O P S I D E D B E

A T T A C H E D W A L L S

O N

W I T H F O A M

F A S T E N E R

5. Installation

a. Attached the separated hook/loop on the desired wall surface

b. Paste the cushion insulator to the hook/loop fastener

INSTALL

c. Continuously attach each cushion to one another until reaching the desired amount

Front view

Side 1 Facing inside

or

Side view

Side 2 Facing inside

6. Materials :

Main Materials

: Felt fabric, Bubble wrap, Aluminium foil,Polyethylene Sponge

Complementary Materials : Hook and loop fastener, Double sided foam tape

Hook and loop fastener

Felt Fabric - Barrier 1 Bubble Wrap - Barrier 2 Aluminium foil - Barrier 3 PE Foam- Barrier 4

Side 1

Felt fabric

Side 2

Hook and loop fastener Able to hold maximum

Composed of interlocked

1500 grams

fibres which makes it a great insulator

Bubble wrap

2 sides with different color, giving flexibility for the users

Trapped heat inside each of the pockets

Aluminium foil Polyethylene Sponge

Reflecting the heat back at the source

A large number of ( Cut in half )

pockets

to prevent heat transfer.

not to scale Have well

sound-insulating as

properties

as

sound-absorbing

7. The making :

a. Each felt fabric cut and attached into one by sewing the edges and left some inches gap

b. PE foam cut and wrapped in aluminium foil

b.ii

b.iii

MM033

b.i

200 MM

d. PE foam & Aluminium foil wrapped in bubble wrap

d.i

d.ii

d.iii

e. Put in the felt pocket through the gap

f. Sewed each of the hook & loop fastener on each fabric side

Side 1

Side 2

g. Cut another hook&loop seperatedly and attached the double sided foam tape

->

h. The finished product

The cushion with 2

The seperated hook & loop

different sides of color

with double sided foam tape

8. Tools and materials cost

Materials

Size

Price

Felt fabric

2pcs x (35cm x 24cm)

RM 1

Bubble wrap.

33cm x 44cm

RM 0.5

Aluminium foil

33cm x 44cm

RM 0.5

PE sponge

33cm x 20cm x 1.5cm

RM 2

Hook and loop fasteners

2pcs x 35cm

RM 1

Double sided foam tape.

1 pc

RM 2

1pc

Free

Tools

Scissors

Free

Thread.

1pc

Rules

Free

Images RM 7

Total cost

9. Design value

Total cost repsonded by the 10 audiences : RM 150 Divided by 10 to get the average price.

: RM 15

Design value = Responded cost - Materials cost = RM 15 - RM 7 = RM 8

Conclusion

By doing this project, I am able to identify the calculation and formula to be proceeded to find and compare the heat transfer of each wall of the chosen space. In which, later will be used as an experiment to find the solution on what product will be made in order to reduce the heat transfer and the other features such as sound proofing and can be used as a cushion. In making the product, it's allowing me to come up with the originality of the design and ideas,

as well as practicing my critical thinking on

choosing which materials are the best, efficient and sold outside.

have a good design value to be

FINAL PROJECT Building Services Design in Kitchen

Karenina Devi Yuwono 0340802

Building Science and Services BLD62304103247

PART 1 (a) Site Study and Re-design Kitchen

Site Study In current situation, there are not much different activities

in the kitchen while on the MCO

compared to before MCO. because we rarely buy take-away food. The kitchen activities starts in the morning around 6 a.m. Since all of our family are coffee drinker, she

make our coffee

traditionally by pouring hot boiling water in a glass with coffee powder in it.

Then she starts to cook breakfast until 9.30 am. In our family we dont eat lunch, only breakfast and dinner.

For dinner, our family chef reheat the meal that were made in the morning, which have been divided into two

portions, for breakfast and dinner. Resulting in

approximately 4 hours for the kitchen operation per day.

Kitchen situation while preparing breakfast

As we can see from the photo above, the main working spaces in the kitchen are on the stove area and the sink area. The ingredients are placed on the countertop in between stove and sink.

Current kitchen layout plan

During this time of period, we spent most of our time inside the house, thus we tend to develop new hobbies, one of them is baking. Especially me and my mom.

Mostly we bake in the evening because it is cooler that in the afternoon, since there are the kitchen

natural ventilation in

Kitchen electrical and lighting plan

As in the electrical and lighting plan, theres one ceiling light in

the kitchen as well as

in the

pantry/dining room. This might raise some lighting problem.

Kitchen water supply and plumbing plan

Based on the water supply and plumbing plan, we can see that they have distributed properly and accurately, thus there will be no additional plumbing pipe. But there might be changes on the path pf the plumbing pipe, which will be analyzed on the following page.

Re-design Kitchen

Stove Placement On the new kitchen design layout, the first thing that I was move the position of the stove. On the previous layout of the kitchen, it can be seen that the stove is placed in front of the window ventilation, which might raises some problem. Based on the experience of the family chef, the window will likely to be covered with a film of oil, spatter, and steam drips, which will take more time and effort to clean. Moreover, if the window glass is exposed to the heat in a long period of time, the window glass will likely to break.

Sink Placement The change of place of the stove resulting in the change of place of the kitchen sink, which are moved in front of the window.

It

makes an effective use of the entire space. This is because there will be no cabinets on top. Resulting in more spacious space that in the previous kitchen layout, which have the cabinet on top of the sink.

Coffee Station

Based on the interview, I figured out that it is a necessity for the family to hace a coffee station, emphasizing that all of the family member are a coffee drinker, thus there will be no fuss in preparing the coffee, because we all can enjoy the coffee anytime we want, without preparing and washing the coffee equipment repeatedly. The user will also be able to enjoy the view outside the window through the dining area.

Refrigerator Placement

On the previous layout of the kitchen, the refrigerator is blocking the pathway and sight to the window. Moreover, the power usage of fridge are inefficient since the family does not really use the fridge. Therefore I propose the placement change of the fridge as well as the replacement of usage model.

the refrigerator to the lower power

PART 1 (b) Designing and Justification of Building Services Selection & Location

Electrical, lighting and VAC

The change of the lighting placement are based on the experience that the cook's faced such as blocked light, and insufficient lighting. Therefore, I propose a

new location of the lighting right

above the work surface (kitchen and pantry countertop) and

it prevents the user's body from

blocking the light when he or she stands at the counter working. It also throws light directly into open drawers. Another popossal is to add LED lightstrip under the countertop on the stove area to provide sufficient lighting Other than lighting, I also proposed a new outlet at the coffee station so that the user can operate the coffee machine.

The needs of the cooker hood are essentials for every kitchen. It will remove odors, smoke, grease and other pollutants that are released into the air while cooking and also easier in cleaning because it will prevent the growth of bacteria and mold.

Water supply and plumbing

The

usage

of

U

shaped

trap

is

to

prevent foul odour and insects in the soil pipe from entering the premises a

Fire Safety

The

original

kitchen

countertop

materials

are

ceramic tiles, and I will leave it to the original since it impervious to heat and water, won't stain, and less expensive than any other materials.

PRODUCED BY AN AUTODESK STUDENT VERSION

A

3400

3600

2200

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

B

COFFEE STATION

OVEN

3800

DINING TABLE

WASHING ROOM REF

PANTRY & DINING AREA

1645

KITCHEN

UTILITY ROOM

FAMILY ROOM

A

B

PL NEW KITCHEN PLAN 1 : 50

DRAWN BY : KARENINA D.Y. ID NO : 0340802 SUBJECT : BLD6230410324

ASSIGNMENT :

SCALE : 1 : 50

FINAL PROJECT

DATE : MONDAY, 3O NOV LECTURER : MS SHARON

PRODUCED BY AN AUTODESK STUDENT VERSION

NOTE

PRODUCED BY AN AUTODESK STUDENT VERSION

TO OTHER PLUMBING COFFEE STATION

OVEN

DINING TABLE

WASHING ROOM

TO SEWER

REF

PANTRY & DINING AREA

KITCHEN

LEGEND

UTILITY ROOM

FAMILY ROOM

SYMBOL

DESCRIPTION WATER SUPPLY WASTE WATER

TO OTHER PLUMBING

PL WATER SUPPLY AND PLUMBING PLAN 1 : 50

DRAWN BY : KARENINA D.Y. ID NO : 0340802 SUBJECT : BLD6230410324

ASSIGNMENT :

SCALE : 1 : 50

FINAL PROJECT

DATE : MONDAY, 3O NOV LECTURER : MS SHARON

PRODUCED BY AN AUTODESK STUDENT VERSION

NOTE

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

WATER TANK

PRODUCED BY AN AUTODESK STUDENT VERSION

OVEN

DINING TABLE

WASHING ROOM REF

PANTRY & DINING AREA

KITCHEN

UTILITY ROOM

FAMILY ROOM

LEGEND

PL ELECTRICAL WIRING AND LIGHTING PLAN

SYMBOL

1 : 50

DESCRIPTION SINGLE OUTLET DOUBLE OUTLET CEILING LIGHT TWO-GANG SWITCH SINGLE GANG SWITCH ELECTRICITY WIRING SWITCH WIRING

DRAWN BY : KARENINA D.Y. ID NO : 0340802 SUBJECT : BLD6230410324

ASSIGNMENT :

SCALE : 1 : 50

FINAL PROJECT

DATE : MONDAY, 3O NOV LECTURER : MS SHARON

PRODUCED BY AN AUTODESK STUDENT VERSION

NOTE

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

COFFEE STATION

EL ELEVATION A 1 : 20

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

LEGEND SYMBOL

DESCRIPTION ELECTRICITY WIRING

DRAWN BY : KARENINA D.Y. ID NO : 0340802 SUBJECT : BLD6230410324

ASSIGNMENT :

SCALE : 1 : 20

FINAL PROJECT

DATE : MONDAY, 3O NOV LECTURER : MS SHARON

PRODUCED BY AN AUTODESK STUDENT VERSION

NOTE

EL ELEVATION 1 : 20 B

LEGEND SYMBOL

DESCRIPTION ELECTRICITY WIRING

DRAWN BY : KARENINA D.Y. ID NO : 0340802 SUBJECT : BLD6230410324

ASSIGNMENT :

SCALE : 1 : 20

FINAL PROJECT

DATE : MONDAY, 3O NOV LECTURER : MS SHARON

PRODUCED BY AN AUTODESK STUDENT VERSION

NOTE

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION

PRODUCED BY AN AUTODESK STUDENT VERSION