Dear Woodworker:
Thank you for your purchase and welcome to the Laguna Tools group of discriminating woodworkers. I understand that you have a choice of where to purchase your machines and appreciate the confidence you have in our products. Every machine sold by Laguna Tools has been carefully designed and well thought through from a woodworker’s perspective. I cut on our bandsaws, lathes, table saws and combination machines. Through my hands-on experience, I work hard to make our machines better. I strive to give you machines that inspire you to create works of art. Machines that are a joy to run and work on. Machines that encourage your performance. Today, we offer high-performance machines with innovative solutions that meet the needs of woodworkers and their ever-evolving craft. I started Laguna Tools as a woodworker; I still am. Thank you again for becoming a Laguna Tools customer.
Torben Helshoj President and Founder – Laguna Tools Imagination, Innovation and Invention at work.
Table of contents Safety Rules
Page number 4
Warranty
5
Noise emission
6
Specification sheet
6
Receiving your planer
7
Introduction to your planer
7
What you will receive with the planer
8
Parts of the planer
9
Where to locate your planer
10
Unpacking your planer
11
Assembly and setup
12
Running and adjusting the planer
16
Maintenance
23
Troubleshooting
24
Electrical drawing
27
Exploded view drawings and parts lists
28
3
Safety Rules As with all machinery, there are certain hazards involved with the operation and use. Using it with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you have any questions relative to the installation and operation, do not use the equipment until you have contacted your supplying distributor. Read carefully before operating the machine. 1. Keep the working area clean and be sure adequate lighting is available. 2. Do not wear loose clothing, gloves, bracelets, necklaces or ornaments. Wear face, eye, respiratory and body protection devices as indicated for the operation or environment. 3. Be sure that the power is disconnected from the machine before tools are serviced or an attachment is to be fitted or removed. 4. Never leave the machine with the power on. 5. Do not use dull, gummy or cracked cutting tools. 6. Be sure that the keys and adjusting wrenches have been removed and all the nuts and bolts are secured.
4
Limited Warranty New woodworking machines sold by Laguna Tools carry a one-year warranty from the date of shipping. Laguna Tools guarantees all new machines sold to be free of manufacturers’ defective workmanship, parts and materials. We will repair or replace, without charge, any parts determined by Laguna Tools, Inc., to be a manufacturer's defect. We require the defective item/part to be returned to Laguna Tools. In the event the item/part is determined to be damaged due to lack of maintenance, cleaning or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused when repair or alterations have been made or attempted by others. Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. woodworking machine. Warranty may be voided upon the addition of such noted tools and/or modifications, determined on a case-by-case basis. Normal user alignment, adjustment, tuning and machine settings are not covered by this warranty. It is the responsibility of the user to understand basic woodworking machinery settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer. Parts, under warranty, are shipped at Laguna Tools, Inc's cost either by common carrier, FedEx Ground service or similar method. Technical support to install replacement parts is primarily provided by phone, fax, or e-mail. The labor required to install replacement parts is the responsibility of the user. Laguna Tools is not responsible for damage or loss caused by a freight company or other circumstances not in our control. Only new machines sold to the original owner are covered by this warranty. For warranty repair information, call 1-800-332-4094. Copyright 2010 Laguna Tools, Inc. ** Warning – no portion of these materials may be reproduced without written approval from Laguna Tools, Inc. All documentation subject to change without notice
5
Noise emission. Notes concerning noise emission Given that there exists a relationship between noise level and exposure times, it is not precise enough to determine the need for supplementary precautions. The factors affecting the true level of exposure to operators are clearly the amount of time exposed, the characteristics of working environment, other sources of dust and noise, etc. For example, adjacent machines, in other words, affect the level of ambient noise. It is possible that exposure level limits will vary from country to country. Specification sheet. Machine Motor Planer table size Planer table extension rollers Cutter head Dust chute diameter Max planer width Max planning height Maximum planning depth Maximum moulding depth Feed speeds Cutter speed Volts Weight net/gross Packaging size
MPL3000-0120 13" Planer/Moulder 2 HP 17-3/4" x 13" (450mm x 330mm) Yes 3 knives (included) 4 inches (100mm) 13" (330mm) 6" (152mm) 1/8" (3.2mm) 3/4" [19mm] 2 speed (12 and 20 FPM) 5000 RPM 220 V, single phase 275 lbs/295 lbs (120kg/135kg) 26 3/8" x 19 7/8" X 45 3/8" (670mm x 500mm x 1150mm)
6
Receiving your machine. Note. It is probable that your machine will be delivered by a third party. Before you unpack your new machine, you will need to first inspect the packing, invoice and shipping documents supplied by the driver. Ensure that there is no visible damage to the packing or the machine. You need to do this prior to the driver leaving. All damage must be noted on the delivery documents and signed by you and the delivery driver. You must then contact the seller (Laguna Tools) within 24 hours. Introduction to planer/moulders. The planer/moulder is designed to give you years of safe service. Read this owner’s manual in its entirety before assembly or use. The planer/moulder is generally defined as a machine that cuts planks of wood smooth and parallel and that can also produce mouldings. The machine achieves this by the plank being pushed by powered rollers along a flat table under a revolving cutter head. There are many types of cutter heads, but this machine uses a three-blade configuration. The parallel blade system gives a finish without lines, and this also allows the insertion of the moulding blades into the same cutter head. Additional Instructions for the use of planer/moulder. Like all machines, there is danger associated with the machine. Injury is frequently caused by lack of knowledge or familiarity. Use this machine with respect. If normal safety precautions are overlooked or ignored, serious personal injury may occur. 1. Supporting the work. Only make cuts if the work piece is stable and never attempt to cut unstable planks or injury may occur. 2.Cutting depth. Never exceed the maximum cutting depth as stated in the specification for your machine. It is far better to take several small cuts rather than large cuts. 3. Direction of cut. Planing against the grain is dangerous and could produce chatter or excessive chip out. Always plane with the grain. 8.Guards. Guards are designed to reduce the risk of injury. Always use the guards. 10. Stock. Your safety will be greatly enhanced if you only use good lumber. Only work with lumber after you have inspected it completely. Staples, nails, loose knots and any other metal in the plank will damage your cutter head and could cause injury or fire. If you have any question about a piece of lumber, do not use it.
7
What you will receive with the planer. 1
5
2
6
7
8
9
3
4
10
1. Roller support plates. 2. Guides. 3. Rollers. 4. Dust chute. 5. Leveling feet. 6. Gear box handle. 7. Gibs. 8. Screws. 9. Guide support rod. 10. Handles.
8
Parts of the planer/moulder. 6
9
7
1
2
3
4
5 8
11
12
10
9
The planer/moulder major parts are discussed in this manual. If you are not familiar with the planer/moulder, take the time to read this section and become familiar with the machine. 1. Body. The body is made from pressed steel and is designed to give the machine support and rigidity. 2. Lifting rods. The lifting rods are extendable from the machine. Lifting strops can be attached to the rods when lifting or moving the machine. 3. Support rollers. The support rollers support the work piece and effectively extend the table area. 4. Start/stop switch. 5. Power cable. A power cable is supplied with the machine. The plug may not suit your electrical installation and may have to be replaced. 6. Table. The table is made from cast iron and supports the work while it is being machined. The table has a fine ground finish. 7. Guides. Adjustable guides are provided to adjust the position of the work when using the machine moulder function. 8. Dust chute. A 4-inch diameter dust chute is provided. The dust chute must be connected to a dust collector with a minimum capacity of 1000 c.f/m. The machine produces a lot of sawdust and wood chippings; the stronger the dust collector the better. 9. Table adjusting handle. The table adjusting handle raises and lowers the table. 10. Motor. The motor provides the power to the cutter head. 11. Cutter head. The cutter head takes three planer knives or three moulder knives. 12. Tool tray. The tool tray is located on the top of the machine for ease of access. It stores all the tools and setting jigs that are supplied with the machine. Where to locate your machine. Before you remove your machine from the pallet, select the area where you will use your machine. There are no hard-and-fast rules for its location, but below are a few guidelines. 1. There should be an area at the front and back of the machine suitable for the length of wood that you will be machining. 2. Adequate lighting. The better the lighting, the more accurate and safely you will be able to work. 3. Solid floor. You should select a solid, flat floor, preferably concrete or something similar.
10
4. Close to power source and dust collection. Unpacking your machine.
Boxed machine
Box removed
Pallet securing bolts Side panel removed, parts inside To unpack your machine, you will need tin snips, knife and a wrench.
11
1. Using the tin snips, cut the banding that is securing the machine to the pallet (if fitted). WARNING: EXTREME CAUTION MUST BE USED BECAUSE THE BANDING WILL SPRING AND COULD CAUSE INJURY. 2. Lift the box off and discard. 3. Using the knife, cut the plastic wrap from the top. The accessories that were ordered could be attached to the side of the machine, and extreme caution must be taken so that the parts do not fall and cause injury or damage. Remove them and set aside. 4. Some of the parts supplied with the machine may be shipped inside the machine. To access these parts, remove the machine side panels. 4. Remove the base mounting bolts that secure the machine to the pallet. The mounting bolts are accessed from underside of the pallet. 5. The machine can be lifted using a forklift truck or hoist. If no forklift truck or hoist are available, the machine can be removed from the pallet as follows. Note. The machine is heavy, and if you have any doubt about the described procedure, seek professional assistance. Do not attempt any procedure that you feel is unsafe or that you do not have the physical capability of achieving. With two or more people, move the machine so that the base of the machine is over the edge of the pallet. Tilt the machine away from the pallet so that the base of the machine touches the floor, slide the pallet from under the machine and then move the machine to the vertical position so that it is completely resting on the floor. To lift the machine off the pallet using a sling, pull the lifting rods out from the machine’s main body. Fit the sling around the sling rods and lift the machine off the pallet with a hoist. The hoist must have a lifting capacity of no less than 2000 lbs. Remove the pallet and lower the machine to the floor. Assembly and setup. Fitting the leveling feet. 1. Raise the machine off the ground onto wooden blocks. 2. Fit a leveling bolt to the four corners of the machine into the tapped holes that the pallet fixing bolts have been removed from. 3. Lower the machine to the ground and place a spirit level on the table of the machine. 4. Adjust the leveling feet until the Leveling feet spirit level shows that the table is level in both directions and that the machine will not rock.
Fixing hole
Note. If you move the machine, you may find that the leveling bolts will need to be readjusted.
12
Fitting the support rollers.
Support roller Support roller plates 1. Attach the support roller plates to the side of the table, both inand out-feed sides. Do not fully tighten. 2. Fit the support rollers to both in- and out-feed sides of the machine. 3. Using a straight edge, adjust the rollers level with the table and fully tighten Straight edge the fixing screws. Note. You have to check for level at both sides of the rollers.
13
Fitting the gear box engage/disengage handle. Screw on the gear box handle and tighten the lock nuts.
Fitting the guides. Gear engage/disengage handle
Guides Guide support shaft Fit the guide support shaft to the in- and out-feed sides of the machine. Attach the guides and secure with the clamping screw knobs. Fitting the dust chute.
Dust chute
Upper fixing screws
Lower fixing screws
14
Note. The dust chute has to be removed to access the cutter head. Attach the dust chute with the upper and lower fixing screws. Connecting the electrical supply. Note. A qualified electrician must carry out the installation. Ensure that the electrical supply corresponds with that of the machine (single-phase 220 V). It is recommended that you use a 30-amp mains breaker. If you need a longer cable than that supplied on the machine, you can connect a new cable into the internal power termination. Note. The machine is not normally supplied with an electrical plug, as the type of plug will be dependent on the installation.
Internal power termination
Connecting the dust collection. Connect a 4-inch flexible hose between the dust collection hood and your dust collector. Once fitted, pull on the hose to ensure that the connection is tight. You do not want it to come off during production. Note. You will need a dust collection system with a minimum of 1000-cubic-feet-per-minute capacity. The stronger the dust collection the better, as the machine is capable of producing a lot of waste.
Dust collection hood
Cleaning the machine. The machine is shipped with the non-painted surfaces protected from rust by a film of grease. The grease must be removed with WD40 or similar, as it attracts saw dust and dirt. The surfaces should then be coated with a Teflon lubricant or similar. Anti-kickback teeth Teflon tends to dry and will not attract sawdust and dirt. To reduce table friction, it is recommended that the table is polished with a good-quality wax. This will also afford a degree of protection from rust. Anti-kickback teeth. The anti-kickback teeth must be free to move, or they will not fulfill their function. With the power disconnected, check that all the teeth move freely. If they do not, lubricate with Teflon-based lubricant.
15
Running and adjusting the machine. Changing the cutter blades.
Chip breaker
Cutter head
Gib
jacking screw
Disconnect the power from the machine. Never conduct any maintenance or fitting of cutters with the power connected to the machine. 1. Remove the cover and the dust hood. 2. Loosen all the screws in the gibs. There are three gibs for each blade.
Gib Blade 3. The gibs clamp the cutter blade and have jack screws that force the gibs vertically. The gib and slot in the cutter head are tapered, and the vertical movement clamps the blade to the cutter head. When the machine is prepared for shipping, all the parts are greased. This may cause the gib to stick in place. Cut a piece of wood to the approximate shape shown above, loosen the gib jacking screws and give each gib a sharp knock. This will force the gib down and break the joint between the gib and the cutter head.
16
4. The blade will probably also be stuck against the cutter head. If the blade will not easily slide vertically, loosen by prying sideways as shown with a screwdriver. Care must be taken not to damage the blade or yourself while extracting the blades. 5. Clean the gibs, cutter head and blades. Take exceptional care when cleaning the blades; they are very sharp and could cause injury. Take great care in cleaning the cutter head slots, as this will ease later removal of the blades. Fitting and adjusting blades. Disconnect the power from the machine. Never conduct any maintenance or fitting of cutters with the power connected to the machine. The blades rest on two jack screws (one each end of the cutter head). The jack screws adjust the height of the blade. 1. Fit the gibs into the cutter head slot. 2. Fit the blade into the cutter head slot. 3. Loosely adjust the gib screws so that there is very little clearance between the gib and the blade but ensure that the blade is not clamped. 4. Hold the setting jig on the cutter head with the raised portion over the blade. Raise the cutter head jacking screw until the edge of the blade just touches the raised portion. Take care when raising the jacking screw that no excessive force Brass-tipped rod is placed on the blade cutting edge, or you could damage it. 5. Repeat for the other end of the blade. 6. Holding the blade tight against the jacking screw with the brass-tipped rod, fully tighten the jacking screws. 7. Repeat for the other blades. 8. Adjust the red chip breaker so that there is a small clearance between it and the edge of the blade. Ensure that the screws are tight. 9. Rotate the cutter head by hand to ensure that it rotates freely. 10. Refit the top cover and dust chute. Note. There is a short gib in the center of the cutter head. This is used for fitting moulder blades. This, along with the spacer, must be fitted when using planer knives to ensure that the blade is fully supported and clamped.
17
Fitting moulder blades. Disconnect the power from the machine and never conduct any maintenance or fitting of cutters with the power connected to the machine. The moulder blades are fitted into the same slots in the cutter head as the planer blades. When fitting moulder blades, do not fit the two outside gibs. Only use the central gib. 1. Fit the setting jig. 2. After cleaning the slot blade and gib, fit the gib and moulder blade into the cutter head slot. 3. Loosely adjust the gib screws so that there is very little clearance between the gib and the blade but ensure that the blade is not clamped. 4. Using the brass-tipped rod, hold the blade firmly Moulder blade Setting jig down onto the bottom of the cutter head slot while the edge of the blade is just touching the setting jig and tighten the gib jacking screws. 5. Repeat for the other blades. 6. Adjust the red chip breaker so that it is fully clear of the cutters. Ensure that the screws are tight. 7. Rotate the cutter head by hand to ensure that it rotates freely. 8. Remove the setting jig and refit the top cover and dust chute. Setting the guides. Disconnect the power from the machine. Never conduct any maintenance or fitting of cutters with the power connected to the machine. The guides can be adjusted to any position on the table. They must be set in relation to the moulder blades as follows. 1. Place the wood to be moulded on the table against one of the guides. 2. Raise the table so that the moulder blade almost touches the job.
Guides
18
3. Loosen the guide and move to align the job with the cutter head and clamp. 4. Bring the other guide up against the job and clamp in position. 5. Check that the job moves freely without excessive clearance. Test Run. Now that the assembly is complete, it is time to conduct a test run. During the test run, you will check the following points. 1. Motor starts and runs smoothly. 2. The stop button functions correctly. Before you run the machine, check the following. 1. All the tools have been removed from the machine. Start / stop buttons 2. All the guards are in place. Start / stop button 3. You are wearing the appropriate closed safety equipment. 4. You have read and understood the instruction manual. Note. If any of the below functions fail to operate correctly, the fault must be corrected prior to continuing to the next test. Any investigation to find or correct a fault must be conducted with the power disconnected. Note. The stop button, when pressed in, with remain in the off position until reset. To reset the stop button, unlatch the cover. Check that the cover is unlatched prior to conducting the below tests. 1. Put the gear box handle in the neutral position. Note. Never start the machine with the gearbox engaged. 2. Start the machine by pressing the green start button. The machine should run smoothly with little or no vibration. 3. Press the red stop button. The machine should slow down and stop. Adjustments. Note. The machine has had all its functions calibrated at the factory, but due to shipping conditions, some movement may have taken place. This is unavoidable, and it is therefore recommended that the following checks are made prior to starting production. As the machine is used, some functions may move, and it is good practice to know the process for adjusting the machine prior to production.
19
Adjusting the planer/moulder table height.
Table height adjustment handle
Height scale
Height pointer
Move the table to the thickness that you require. Note. Until you get experience with the machine, it is suggested that after setting the table thickness you machine a scrap piece of wood and check that the thickness is correct before you machine your production. Setting the table height indicator. Plane a piece of scrap wood and measure the thickness. Loosen the height pointer and adjust to the planed thickness. Note. There are two height scales (one on either side of the table). Both height pointers have to be adjusted to the same dimension. Adjusting the drive belts. The drive belts should be checked after running the machine for approximately 10 hours. The belts embed into the pulleys and will slacken off slightly. If they are not adjusted, slippage may accrue, and this will cause early belt failure. There should be approximately 3/16" deflection when the belt is pressed with moderate finger pressure. To increase the tension on the belts, loosen the support bracket nuts. Move the bracket down and re-tighten the nuts. Note. To access the drive belts and motor, remove the side covers. Note. Disconnect the power to the machine prior to conducting machine adjustments or repairs.
Motor
Adjustment slots
20
Adjusting the feed rollers. The table rollers come factory set 1/8" below the cutter head to suit the planer function. When moulding, the feed rollers have to be adjusted to suit the job. It is not possible to be accurate in determining the feed roller height, as this will depend on the profile that is being used. A good rule of thumb is to set the rollers 1/4" below the cutter head and fine tune as required. Checking the height of the rollers. 1. Place a piece of hardwood on the table. 2. Bring the table up until it just touches the in- and out-feed rollers. Note the height reading. 3. Bring the table up until it just touches the cutter blade (the rollers are spring loaded and will move up). Note the height. 4. The difference between the two readings is the distance the rollers are lower than the cutter blade. Checking that the rollers are parallel to the table. 1. Place a piece of parallel hardwood approximately 1-inch wide on the table under the in-feed roller at one end. 2. Bring the table up until the wood just touches the roller. 3. Move the wood to the other side under the same roller and check that it just touches the roller. 4. If there is a difference, the roller height should be adjusted. 5. Repeat for the other roller. Adjusting the roller heights.
Roller height adjusters Lock nut Cap 1. Unscrew the caps and remove. 2. Loosen the lock nut. 3. The threaded shaft has flats to suit the wrench supplied. Adjust the shaft to suit the adjustment required. 4. Tighten the lock nut and replace the cap. Note. There is a nut on the top of the threaded shaft. Do not loosen the nut, as this adjusts the spring pressure and is factory set.
21
Adjusting the table parallel to the cutter head.
Chain tension bracket
Sprocket
The table is factory set parallel to the cutter head and should not need adjustment. If the machine is producing a tapered cut, adjustment can be made as follows. Disconnect the power from the machine. Never conduct any maintenance or fitting of cutters with the power connected to the machine. 1. Place a piece of parallel hardwood approxiimately 1-inch wide on the table at one side under the cutter head. 2. Raise the table so that the wood just touches the cutter head (not the blade). 3. Remove the wood and check the other end of the cutter head. Both ends should be the same. 4. If both sides are the same, then no adjustment is required and, in all probability, the blades have been installed correctly. If they are different, loosen the chain tension bracket and move back. 5. Remove the chain from one sprocket and turn the sprocket. Only a small adjustment should be required, and it is suggested that the sprocket should be turned two teeth at a time. 6. Replace the chain. 7. Re-tension the chain and lock the adjuster in place. 8. Recheck the table to cutter head. Note. Mark the sprocket positions before removing the chain, or you could end up confused as to what the original setting was.
22
Installing a bed board. Certain operations require that the cutter cuts through the job. This will require that you make and fit a board to the table of the machine. Four holes are provided in the table to attach a board. The dimensions of the board are not important, but it is suggested that the board is 12 3/8" wide x Board fixing holes 31 1/4" long and a minimum of 1/4" thick (depending on the amount you want to cut through the job). You will need four 3/8" x 1" countersunk screws to attach the board to the table. (Screws not supplied.) Note. The screws must be sub flush. Note. To reduce friction, it is suggested that the board is waxed after assembly. Maintenance. As with any machine, to ensure optimal performance, you must conduct regular maintenance. Daily checks. 1. Clean the machine and lubricate unpainted surfaces with a Teflon-based lubricant. Wipe off any excess and buff with a dry polishing cloth. This will reduce the likelihood of rust forming and reduce the friction on the tables as the wood is machined. 2. Check cutter blades for chips and dullness. 3. Generally inspect the machine for damage and loose or warn parts. Weekly checks. 1. Clean the cutter head. 2. Check cutter blades for chips and dullness. 3. Generally inspect the machine for damage and loose or worn parts. 4. Check the dust extraction for blockages and any large bits that could cause blockages. Monthly checks. 1. Check the motor drive belts for wear, splits and cuts. 2. Clean the motor compartment and the motor to ensure that the motor cooling fins work efficiently. 3. Clean and lubricate the drive chains and cogs. 4. Generally inspect the machine for damage and loose or worn parts. Note. It is recommended that you use a Teflon-based lubricant. Drive belt replacement. Note. Disconnect the power to the machine before conducting any maintenance on the machine. 1. Remove the side cover to access the motor.
23
2. Loosen the motor clamping nuts as detailed earlier in the manual. 3. Remove the drive belts. 4. Fit the new belts. 5. Re-tension the belts. There should be a 3/16" deflection when the belt is pressed with moderate finger pressure. Tighten the motor clamping nuts. 6. The drive belts should be checked after running the machine for approximately 10 hours. The belts bed into the pulleys and will slacken off slightly. If they are not adjusted, slippage may accrue, and this will cause early belt failure. There should be a 3/16" deflection when the belt is pressed with moderate finger pressure. 7. Refit the side cover. Lubricating the machine. Note. All the bearings are sealed for life and do not require lubrication. If a bearing is noisy, do not try to re-lubricate but replace it. Note. It is recommended that you use a Teflon-based lubricant, as it tends to dry and therefore will attract less sawdust and dirt. Lubricate the drive chains and cogs.
Troubleshooting and fault finding. Problem Cause Motor will not start or 1. Emergency button fuses or circuit breakers depressed. blow. 2. Short circuit 3. Start capacitor faulty. 4. Motor thermal protection circuit breaker faulty, or motor is at fault. 5. Open circuit in motor or loose connections. Fuses or circuit breakers blow.
Motor will not develop full power or motor speed slows with load, over heats or stalls.
1. Motor drawing excessive current. 2. Cutter head or motor jammed. 3. Short circuit. 1. Motor run capacitor faulty.
2. Machine overloaded. 3. Motor overheating.
Corrective action 1. Reset the emergency button. 2. Repair or replace short circuit item. 3. Fit new capacitor. 4. Replace thermal protection circuit beaker in motor or replace motor. 5. Replace or repair motor or loose connection. 1. Repair or replace motor. 2. Remove jam. 3. Repair or replace short circuit item. 1. Replace the capacitor.
2. Take smaller cuts. 3. Clean motor, taking
24
4. Short circuit in motor or loose connections. Cutter head slows or belt squeals when cutting.
1. V-belts loose.
2. V-belts worn out. Loud noise coming from 1. Motor pulley set machine. screws or keys are missing or loose. 2. Drive belts are damaged. Tables are hard to adjust. 1. Table spindles are tight. Job stops or slows during 1. Taking too of a deep cut. cut. 2. Pitch or buildup on planer components. Chipping or marks 1. Knots or conflicting (consistent pattern). grain direction in wood.
Furry finish on the grain.
Lines or ridges that run along the board. Chatter marks across the face of the board. Uneven blade marks. Shiny finish.
2. Nicked or chipped blades. 3. Taking too of a deep cut. 1. Wood has high moisture content or surface wetness. 2. Blunt blades. 1. Nicked or chipped blades. 1. Worn cutter head bearings. 1. Blades are blunt. 2. Too fine a cut.
Chip marks, random pattern.
1. Chips not removed from cutter head.
Snipe.
1. Dull blades. 2. Inadequate support for long board. 3. Uneven feed roller
care to make sure that all the cooling fins are clean. 4. Repair or replace motor or loose connections. 1. Tighten V-belts. 2. Replace V-belts. 1. Replace or tighten if necessary. 2. Replace drive belts. 1. Clean and lubricate spindles. 1. Take smaller cuts. 2. Clean the tables and cutter head components 1. Inspect job for knots and grain direction; only use good material. 2. Replace affected blades. 3. Take smaller cuts. 1. Check moisture content and allow to dry. 2. Replace the blades. 1. Replace blades. 1. Replace cutter head bearings. 1. Replace the blades. 2. Increase the depth of cut. 1. Use a dust collection system or a stronger dust collection system 1. Replace blades. 2. Use support stand. 3. Reset feed rollers.
25
Torn grain.
Poor feeding of job.
Tapered cut.
Table difficult to adjust vertically.
tension. 1. Cut too deep. 2. Cutting against the grain. 3. Dull blades. 1. Low feed roller pressure. 2. Motor belt slippage. 3. Table dirty. 4. Feed rollers worn. 1. Table not parallel to cutter head. 2. Blades not adjusted correctly. 1. Cutter head not parallel to table.
1. Reduce cut. 2. Cut with the grain. 3. Replace the blades. 1. Reset feed rollers. 2. Re-tension drive belts. 3. Clean table. 4. Replace feed rollers. 1. Reset table to cutter head. 2. Reset blades. 1. Adjust table to cutter head.
26
Electrical drawing.
27
Exploded view drawings.
28
29
30
Copyright 2010 Laguna Tools, Inc ** Warning – no portion of these materials may be reproduced without written approval from Laguna Tools, Inc. All documentation subject to change without notice
31