spk007-2_im

SPK007 MARINE STEREO 6x9 2 WAY

COAXIAL SPEAKERS

T e c h n i c a l s p e c i f i c a t i o n s & C U T T IN G T E M PLA T E

A Division of Standard Communications Pty. Ltd. Head Office: Sydney- Locked Bag 2086, North Ryde, NSW 1670, Australia. Tel: +61 (0)2 9844 6666 Fax : +61 (0)2 9844 6600

MELBOURNE ADELAIDE PERTH 7 Micro Circuit Unit 1, 14 Phillips Street Unit 1, 10-12 Harvard Way DANDENONG STH 3165 THEBARTON 5031 CANNING VALE 6155 Tel: (03) 9798 0988 Tel: (08) 8234 2633 Tel: (08) 9455 5744 9798 0177 Fax: (08) 8234 5138 Fax: (08) 9455 3110

BRISBANE SYDNEY AUCKLAND Unit 1, 89-101 Factory Road Unit B, 22-24 College Street Unit 2, 24 Bishop Dunn Place OXLEY 4075 GLADESVILLE 2111 East Tamaki, MANUKAU 2013 Tel: (07) 3278 6444 Tel: (02) 9879 8888 Tel: (09) 274 0955Fax: (03) Fax: (07) 3278 6555 Fax: (02) 9816 4722 Fax: (09) 274 0959

For customers outside Australia and New Zealand please contact your local GME Distributor or email: export@gme.net.au www.gme.net.au

Part Number: 310436 Drawing Number: 44316-2

Mounting instructions

Speaker driver specifications

PRECAUTIONS

MOUNTING

1. Please avoid contact with inside speaker wire

1. When mounting the SPK007 in the kick panel, make sure there is a clearance of 90 mm (3.5”) behind the well.

2. Do not change the polarity of the speaker terminal assembly

SPK007 System Power (Watts) Tweeter - mm (inches) Efficiency (1W/1 M)

76.5 mm (3”)

Frequency Response Impedance (Ohms) Weight - kgs (lbs)

111.5 mm (4.4”) 86 mm 3. Make sure lead and speaker terminals do not contact metal.

4. When making connections, please refer to the instruction manual of marine stereo used.

CONNECTING 1. Attach the speaker wires (supplied) to the speaker terminals be sure to connect the correct spade connector to the correct size terminal.

To Amp /Stereo

2. Connect the other end of the speaker wires to your amplifier/stereo ensuring ‘+’ goes to ‘+’ and ‘–’ goes to ‘–’.

(3.4”) 2. Push out the template from this leaflet and use to mark the position of the mounting screws and the outline of the speaker hole.

Drill the mounting holes and cut the hole for the speaker.

Coaxial speaker 170 13.28 mm (½) Neo PEI Dome 90 db 60 Hz–22 kHz 4 1.69 (3.73)

WARRANTY GME limit this warranty to the original purchaser of the equipment.

GME warrant the SPK007 to be free from defects in material and workmanship for a period of thirty six (36) months from the date of purchase from their authorised retailer.

Should the product require servicing during this period, all labour and parts used to effect repairs will be supplied free of charge. GME reserve the right to determine whether damage has been occasioned by accident, misuse or improper installation whereby the warranty would be void, including equipment which has been damaged due to:

3. Place gasket around hole. Place speaker in hole and using screws supplied screw speaker into place.

(a) Incorrect or reverse polarity connection to a battery or power supply or to an incorrect supply voltage.

4. Cover screws with cover plugs supplied.

(b) Operation without an antenna or by connection to an antenna which has been incorrectly installed, resulting in damage to the speaker’s output circuit.

Procedure to be followed by claimant: In the event of a defect occurring during the warranty period, the original purchaser may return the defective unit along with suitable proof of purchase date (i.e. receipt, docket, credit card slip etc.) and a full description of the defect to the retailer from whom the unit was purchased. All freight charges incurred for transportation by the retailer or GME are the purchaser’s responsibility.

GME AFTER SALES SERVICE Your speaker is especially designed for the environment encountered in land and marine installations. The use of all solid state circuitry, careful design and rigorous testing, result in high reliability.

Should failure occur however, GME maintain a fully equipped service facility and spare parts stock to meet the customer’s requirements long after expiry of the warranty period.

(c) Effects of water or moisture penetration. (d) Non-factory modifications.

S PK0 07

TECHNICAL SPECIFICATION AND CUTTING TEM PLATE

g

h (Pus ole h r ake S pe

out)

Ou ter

e

Tear off here

eo dg

ker ea p fs

ut) ho s u (P rille

Mounting Template for SPK007 Please push out.

S PK0 07

TECHNICAL SPECIFICATION AND CUTTING TEM PLATE

SPK007 Cutting Template

S PK0 07

TECHNICAL SPECIFICATION AND CUTTING TEM PLATE