FITTING INSTRUCTION FOR DOOR LEVERS ON 52mm ROUND OR SQUARE EUROPEAN PRIVACY ROSE WITH LATCH 4
1 For new doors. Select position on door as desired. Using template provided, mark position on door appropriate to back set size of latch supplied. Drill 12mm hole for spindle, ensuring the hole is horizontal.
6
2 Mark on door two hole positions on a vertical plane 38mm centres for round rose or 41mm centres for square rose from spindle position as per template provided. Drill 6mm holes, ensuring the holes are horizontal so through bolts align. (NB to avoid splintering on exit side use a block of wood to drill against). 3 Mark hole for privacy pin. Horizontally 18mm from spindle centre, as per template. Drill 9mm hole squarely from both sides. 4 Ensuring all lose timber is removed and holes are aligned, insert latch into 25mm bore hole correct way up as indicated by arrow. Move latch tongue to correct position according to swing of door and place face plate (2) over tongue. Mark around face plate and screw holes. Remove latch and face plate. Drill small pilot holes for screw holes and carefully chisel out face plate area so face plate will sit flush to door edge.
1
5 Remove Stop Screw (1) and keep safe, replace latch into bore hole, ensuring tongue is in correct position for handing, fix
2 3
6
face plate. Insert swivel spindle (3) into latch follower with open groove facing down and notched stop on exterior side of door.
8
6 On exterior side of door refit Stop screw (1) with small screwdriver. If door thickness requires, fix extension pin (8) to interior side of door.
5 9 7
TEST BEFORE CLOSING THE DOOR ! 1 Press privacy pin in to lock, exterior lever is rigid and will not depress 2 Depress interior lever to retract latch and pop out privacy pin. This releases exterior lever to operate ANTI LOCK OUT TEST – Before you close the door, push in privacy pin to lock, then depress the latch tongue with your thumb. The privacy pin should pop up and free exterior lever simultaneously.
FIXINGS LIST A
7 Carefully remove round roses (4) by twisting off and removing if design allows, (for designs that do not allow full removal slide to grip being careful not to mark grip). For square roses loosen grub screw on underside and remove. 8 Loosen grub screw on underside of door lever (5) to allow handles to fit over spindle and flush to door. Place 60mm through bolts (6) at 12 and 6 O’clock positions through un threaded, counter bored holes on inner rose. Check door thickness, if less than 44mm you will need to cut down each through bolt by appropriate amount to allow 6-8mm of bolt protruding out of door. NB for doors thicker than 45mm you will need extension kits, please contact Turnstyle to purchase these. 9 When bolts are correct length carefully align to find screw holes on opposite rose and tighten up with small flat faced screwdriver. 10 Test levers for free action, if satisfied replace rose covers, notch facing to floor on round roses, for square roses align squarely and tighten up firmly with grub screw. Tighten grub screws on door levers, and screw in privacy pin on interior of door.
(A) 2 of M4 x 60mm thru bolts
H G
(B) 1 of hex key B
11 Test levers and push button to satisfaction (see opposite). Then mark and chisel out for strike plate and dust box (7).
(D) 1 of M6 grub screw
D C
E
(C) 4 of #4 x 1” wood screw (E) 4 of #4 x ¾” wood screw
CONTACT
(F) 1 of 8mm square split spindle F
PART NUMBER : 35695
(G) 1 of privacy pin extension (H) 1 of privacy pin
T : +44 (0)1271 325 325 E : sales@turnstyledesigns.com
W : www.turnstyledesigns.com
Turnstyle Designs Ltd, Baron Way, Roundswell Business Park, Barnstaple, Devon, EX31 3TB, United Kingdom