Air Interlacing DTY False-Twist Texturing Heberlein庐 SlideJet-FT15-2 The unique SlideJet-FT15-2 with new cutting edge jet plates for best interlacing at lowest air consumption The basic principle of the successful SlideJet system is also followed in the new SlideJet-FT15-2. The improved operation is new, as well as simplified service and a clear jet identification: Exchange of jet plates by the press of a button. The slider with jet plate is locked into the housing and unlocked without tools. Jet plates connected to the slider by bayonet locking and no screws. Compatibility of new and old jet plates in the old and new housings. Simple jet plate identification using 7 freely selectable slider colours. Cleaning of the complete jet by spray washing; cleaning of jet plates together with sliders by ultrasonic bath. Cutting edge jet plate range: New P142-2, P143-2, P243-2, P244-2, P246-2 and P247-2 series for extremely regular interlacing with maximum knot count at up to 1200 m/min yarn speed. High as well as low interlacing stabilities are possible depending on air pressure and overfeed. Regular interlacing even at low air pressure that saves energy and protects the yarn, the best preconditions for interlacing microfilament yarns. Proven P212-2, P213-2, P312-2, P412-2 series with vortex chamber, for less but highly stable knots and P310-2, P410-2 series for interlacing with lowest possible knot count.
Our product range Air jets Aspirating, cutting and splicing units Bearings and rollers Friction discs Friction units Spindles Certified Quality ISO 9001-2000
Oerlikon Heberlein Temco Wattwil Inc. Bleikenstrasse 11 路 9630 Wattwil, Switzerland T +41 71 987 44 44 路 F +41 71 987 44 45 www.components.oerlikontextile.com 路 info.heberlein@oerlikon.com
Air Interlacing DTY False-Twist Texturing Heberlein® SlideJet-FT15-2 Performance characteristics Count range [dtex] (den = 0,9 dtex)
Air usage [m3/h]*
Typical range
Formula applies from 0,8 bar pe = pressure [bar]
Special remarks
Jet in use
Very regular interlacing and high interlacing density up to 1200 m/min. Reduced air consumption by means of Air Twist Chamber (ATC).
P142-2
0,562 (pe+1)
P143-2
0,712 (pe+1)
P243-2
0,911 (pe+1)
P244-2
1,142 (pe+1)
P246-2
1,451 (pe+1)
P247-2
1,785 (pe+1)
P212-2
0,911 (pe+1)
P213-2
1,189 (pe+1)
P312-2
1,859 (pe+1)
P412-2
2,772 (pe+1)
P310-2
0,911 (pe+1)
P410-2
1,189 (pe+1)
Less but long interlacing knots, high stability, wide range of application
Lowest possible interlacing density
Limits of application
50
78
110 167 240 330 450 660 800 990 1200 1600
Air consumption
Dimensions and weight
qvn [m3/h]*
qvn [m3/h]*
14
22
P412
20
13
18
11
16
10
14
P312
12
P247
12
P246
9
P244
8 7
10 8
P213, P410
6
P212, P310
P243
6
P143
5
P142
4 3
4
2
2
1 0
0 0
1
2
3
4
5
6
0
1
pe [bar]
pe = Pressure (gauge) [bar] qvn = Air consumption [m3/h]*
SlideJet-FT15-2: Weight 58 g (without nipple and connector), dimensions in mm
2
3
4
5
6
pe [bar] psi = 14,7 x bar CFM = 0,588 x m3/h
* Under standard conditions according to DIN 1343: Temperature = 0 °C, pressure = 1,01325 bar, relative humidity = 0% (1 standard cubic metre = 1,293 kg) Losses in the compressed air system have not been considered
Compressed air requirements – Pressure fluctuations max. ± 0,1 bar – Temperature 25 °C ± 5 °C – Relative humidity < 40% – Residual oil content < 0,1 ppm ideally oil free (1 ppm ~ 1 mg/m3) – chemically neutral – free from active abrasive particles, particle size > 1.0 μm 100% to be removed Max. allowable air pressure 10 bar
Subject to change without prior notice · © 2011 Oerlikon Heberlein Temco Wattwil Inc., 9630 Wattwil, Switzerland 740281/07 This product is covered by property rights (patent, protected design). Further information see www.components.oerlikontextile.com