Saurer Laser SL4GT / SL5GT / SL6GT / SL8GTR Technical Data Machine types
Laser cutting and engraving system for the Saurer embroidery machines: • All Epoca (Epoca-III only SL8GTR) • Era Laser types: • SL4GT (2-axes-laser) • SL5GT (3-axes-laser) • SL6GT (3-axes-laser) for one embroidery machine • SL8GTR (3-axes-laser) rotatable; for two embroidery machines which needle sides stand opposite to each other
Scope of delivery: • Laser • Laser bridge • PC with control unit software • Safety devices on shuttle side: mechanical device (polycarbonate) and/or electrical device (light barriers) • Fume outlet • Cooling system Options: • Independent test field for laser tests
œrlikon sau rer
H
œrlikon saurer
Sau rer Epoca 05
SL4GT / SL5GT
Height (H)1)
SL6GT
SL8GTR 1)
·
·
·
œrlikon saure r
Saurer Epoca 05
SL8GTR
to the cross bar
2.05 m
total
approx. 2.75 m
Width (B)1)
1.00 - 2.00 m
Length1)
Embroidery length + 4 m
Distance of the fabric levels (D)
2600 - 3100 mm
Length
Embroidery length + 4 m
Depending on the construction of the laser bridge on site and on the laser type
Oerlikon Saurer Arbon Ltd. Textilstrasse 2 9320 Arbon, Switzerland Phone +41 71 447 51 11 Fax +41 71 447 54 11 www.saurer.oerlikontextile.com info@saurerarbon.com
D
Saurer Epoca 05
SL4GT / SL5GT / SL6GT
Dimensions
Saurer Epoca 05
B
Saurer Epoca 05
Saurer Epoca 05
Illustration
Saurer Laser SL4GT / SL5GT / SL6GT / SL8GTR Technical Data Specifications
Laser type
CO2
Nominal rating
50 W/100W
Wave length
10600 nm
Speed
General technical data
Cutting
max. 1000 mm/s
Engraving
max. 4000 mm/s
Engraving and cutting area
Embroidery length x embroidery height (minus approx. 120 mm)
Laser box
SL4GT
2-axes-laser
300 x 300 mm
SL5GT
3-axes-laser
500 x 500 mm
SL6GT
3-axes-laser
800 x 800 mm
SL8GTR
3-axes-laser
800 x 800 mm
Relative humidity: max. 60% at 35° C; max. 90% at 20° C (recommended: 55-65%) Environment temperature: 18 to 35° C (recommended: 20°-30° C) Max. fluctuations: ±2° C Room temperature must be the same as during machine installation! (Air conditioning system is recommended)
Control system
Operation: PC with Laser control unit software, integrated with machine control unit
Cooling system: Forced water cooling Inlet water temperature: min. 20° C, max. 25° C Water quality: Use only demineralised water! Water without contamination, impurity or deposits!
Data format: Saurer laser format (*.lsx), optimally supported with EmStudio up from V3.10
Data interface: LAN
Connections
Electrical supply: 3 x 400 VAC +/- 15% + neutral wire + PE 50/60 Hz Max. current 10 A Overvoltage protection in accordance with the document "Installation, Assembly and Operation Guide" is required.
DS0.0175.E01 07/08
Pre-fusing: 16 A time-delay 3 phases (supply wire gauge min. 5 x 2.5 mm2) If local regulations require the installation of RCCB's, use an RCCB with a sensitivity of 300 mA, selective, pulse-power stable and inverter proof.
Subject to technical modifications